4-Port Antenna B1 B2

Frequency Range 1710–2200 1710–2200

Dual Polarization X X
HPBW 65° 65°
Adjust. Electr. DT 0°–15° 0°–15°
Enhanced Sidelobe Suppression 18dB 18dB
Downtilt set by hand or by optional RCU (Remote Control Unit)

4-Port Antenna 1710–2200/1710–2200 65°/65° 18/18dBi 0°–15°/0°–15°T ESLS

Type No. 80010510V01
Highbands B1; B2
1710 – 2200
Frequency range MHz 1710 – 1880 1850 – 1990 1920 – 2170 2000 – 2200
Polarization ° +45, –45 +45, –45 +45, –45 +45, –45
Gain at 0° tilt dBi 17.5 17.6 17.7 17.8
Horizontal Pattern:
Half-power beam width ° 65 63 62 62
Front-to-back ratio (180°±30°) dB ≥ 30 ≥ 30 ≥ 30 ≥ 28
Cross polar ratio 0° 24 24 24 26
dB
Sector ±60° ≥9 ≥9 > 10 ≥ 10
Vertical Pattern:
Half-power beam width ° 7.9 7.5 7.2 6.9
Electrical tilt ° 0 – 15, continuously adjustable
Sidelobe suppression °T 0 ... 5 ... 10 ... 15 0 ... 5 ... 10 ... 15 0 ... 5 ... 10 ... 15 0 ... 5 ... 10 ... 15
– for first sidelobe above main beam dB ≥ 17 ... 20 ... 18 ... 17 ≥ 16 ... 20 ... 18 ... 18 ≥ 15 ... 19 ... 18 ... 17 ≥ 14 ... 18 ... 18 ... 16
– within 0°–20° sector above horizon ≥ 16 ... 18 ... 18 ... 16 ≥ 16 ... 17 ... 17 ... 16 ≥ 15 ... 17 ... 17 ... 16 ≥ 14 ... 16 ... 16 ... 15
Null-fill at 0° tilt dB 23 22 21 20
Impedance Ω 50
VSWR < 1.5
Isolation, between ports dB > 30
Intermodulation IM3 dBc < –153 (2 x 43 dBm carrier)
Max. power per input W 250 (at 50 °C ambient temperature)
Max. effective power per antenna W 800 (at 50 °C ambient temperature)

Mechanical specifications

Input 4 x 7-16 female

Connector position Bottom
Adjustment 2 x, Position bottom
mechanism continuously adjustable
Wind load (at Rated N | lbf Frontal: 580 | 130
Wind Speed: 150 km/h) Maximal: 635 | 148
Subject to alteration.

Max. wind velocity km/h 200

mph 124
Height / width / depth mm 1389 / 323 / 71
inches 54.7 / 12.7 / 2.8
Category of M (Medium)
mounting hardware
Weight kg 17 / 19.2 (clamps incl.)
lb 37.5 / 42.3 (clamps incl.)
936.4894/b

Packing size mm 1686 x 337 x 112

inches 66.4 x 13.3 x 4.4
Scope of supply Panel and 2 units of clamps
for 42 – 115 mm |
1.7– 4.5 inches diameter

All specifications are subject to change without notice.

The latest specifications are available at www.kathreinusa.com 80010510V01 Page 1 of 2

Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
Accessories
General Information

Accessories (order separately if required) 2)

3)

1)

4)
Remarks Weight approx. Units per
Type No. Description
mm | inches kg | lb antenna

731651 1 clamp Mast diameter: 28 – 60 | 1.1 – 2.4 0.8 | 1.8 2

85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 2
85010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 2
737978 1 downtilt kit Downtilt angle: 0° – 15° 2.3 | 5.1 1
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2

1636 | 64.4
1494 | 58.8
1436 | 56.5
1389 | 54.7
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Wall mounting: No additional mounting kit needed.

Material: Reflector screen: Tin-plated copper. Radiator: Tin-plated zinc.

Flat fiberglass radome: The max. radome depth is only 71 mm. Fiber-
glass material guarantees optimum performance with regards to stability,
stiffness, UV resistance and painting. The color of the radome is grey.
All screws and nuts: Stainless steel.

Grounding: The metal parts of the antenna including the mounting kit and the inner
conductors are DC grounded.

Correlation Table
Adjustment
Frequency range Array Connector mechanism
with integrated long neck
1710 – 2200 MHz B1 1–2 scale
1710 – 2200 MHz B2 3–4 1) 20 | 0.8

5)
2) 72 | 2.8
3) 64 | 2.5
4) 9 | 0.4
5) 35 – 42 | 1.4 –1.7

B1 B2
Left Right

Layout of interface:
254 | 10.0

48 | 1.9
71 | 2.8
41 | 1.6

98 | 3.9

Subject to alteration.

323 | 12.7
936.4894/b

Bottom view
All dimensions in mm | inches

Any previous data sheet issues have now become invalid.

All specifications are subject to change without notice.

Page 2 of 2 80010510V01 The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
 Mounting Hardware
Clamp included in the scope of supply

Suitable for mast diameter 50 – 115 mm

Antenna – mast distance F 18 – 26 mm
Number of pieces 1 clamp
Material of clamp and screws Hot-dip galvanized steel / stainless steel
Weight 1.0 kg

Torque MA = G

Torque:
M8 => MA = 20 Nm
M6 => MA = 8 Nm

A B C D E F G H
152 mm 40 mm 40 mm 50 –115 mm 93 mm 18 – 26 mm 20 Nm 125 mm

Washer
Subject to alteration.
936.4123

All specifications are subject to change without notice.

The latest specifications are available at www.kathreinusa.com Page 1 of 1

Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
 General Instructions
for Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

1
2

2
➀ Adjustment wheel with twist-lock ➀ Thread for fixing the protective To set the downtilt angle exactly,
function. cap or the RCU (Remote Control you must look horizontally at the
➁ Downtilt spindle with integrated Unit). scale. The lower edge of the gear-
scale. ➁ Gearwheel for RCU power drive. wheel must be used for alignment.

Manual adjustment procedure:

0° – max.°

max.° – 0°

Remove the protective cap. Set downtilt angle by rotating the Screw on the protective cap again.
adjustment wheel.

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

Subject to alteration.
936.4144

For a description of RCU installation please refer to the respective data sheet.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com Page 1 of 2

Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
General Instructions for Feederline Installation
on Panels with four Connectors
arranged on two Levels
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.
Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench
width.

Description of connector arrangement:

4 3

2 1

There are four interfaces for feeding the antenna The connectors are mounted at two levels in order to facilitate feederline
located at the bottom. installation.

Attachment of the feederline connector and RCU (optional):

In order to protect the adjustment mechanism the protective caps have to be attached during
feederline installation!

Start with the rearside located inter- After feederline installation the optional For a full description of RCU installation
face no. 1. remote control units (RCU) can be please refer to the respective data sheet.
mounted if required.
Place the connector carefully and fix the
nut using a torque-wrench (according to
the manufacturers guidelines).
Subject to alteration.

The further sequence for the installation

is: feederlines no. 2, 3, 4.
936.4144

Please note: Additional weather sealing of correctly installed feederline connector interfaces is not required,
nor is it recommended by the connector manufacturers.

All specifications are subject to change without notice.

Page 2 of 2 The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]