Pelconet Net350: Product Specification
Pelconet Net350: Product Specification
Pelconet Net350: Product Specification
PelcoNet™ NET350
IP NETWORK VIDEO TRANSMISSION WITH COMPACTFLASH® INTERFACE AND AUDIO
Product Features
• Send and Receive Live Video, Audio, and Control Data Over Ethernet
Networks
• Dual MPEG-4 Video Streams
• CompactFlash® Interface for Local Recording
• Full Integration with Pelco’s Matrices, Genex® Multiplexers,
Spectra® Domes, and Esprit® Positioning Systems
• Adjustable Bandwidth, Image Rate, and Quality
• View Video on PC, Analog Monitor, or Both
• NTSC and PAL
• Alarm Input and Relay Output
• Two Bidirectional Data Channels Via RS-232 and RS-232/422/485
Serial Ports
The NET350 can be used in three ways: The NET350 saves installation costs (no separate cabling required),
•Standalone – as a transmitter or receiver for a camera where BNC allows toll-free operation (intranets), and saves management costs
cable is not possible. This allows one-way video transmission for (single, uniform network). With minimal setup, the NET350 transmis-
fixed cameras or the option of sending control signals to a Spectra® sion system can be installed and running in minutes.
dome or Esprit® positioning system.
•Analog to Ethernet “Bridge” – as a way of using one or more When using a NET350T and a NET350R, connect a camera to a
NET350s connected to a system of Pelco matrices or Genex® mul- transmitter and an analog monitor to a receiver. Then connect the
tiplexers to view video from a vast number of camera analog inputs. transmitter and receiver to the network and configure IP addresses
In this application the analog device is being used as a “concentra- for the equipment using a standard terminal program or any Internet
tor” to allow viewing of hundreds of cameras without incurring the browser. If you need to control a camera (operate pan, tilt, and lens
cost of hundreds of encoders. functions, or do presets and patterns), an RS-232 data interface links
the keyboard controls to the network and then from the network to
•Complete Ethernet System – as a way of controlling an unlimited
the camera system.
number of cameras via NET350s by using Pelco’s VMX series of
matrix control software in a purely Ethernet or hybrid system. Ether-
Instead of (or in addition to) a receiver and monitor, an Internet
net systems involve using an encoder with each camera and using
browser can be used at the receiving end to display video on a PC. On-
the Ethernet as a virtual matrix. This is cost efficient for new instal-
screen keyboards in the NET350 let you control the following devices
lations or add-ons to existing installations. Using the VMX300 as
over the network: System 9760©/9740™ or CM6700/CM6800 matrix
control software for existing systems as well as new Ethernet por-
controller, Genex multiplexers, Spectra domes, and Esprit positioning
tions allows the user to build the industry’s only truly “hybrid” CCTV
systems.
system.
All recordings can be stored locally using a CompactFlash® card or
The NET350 can display video on a PC using Internet Explorer®, an
miniature disk drive (up to 1 GB capacity).
analog monitor, or both.
The NET350T, featuring CompactFlash and dual MPEG-4 video
PelcoNet™ transmits (NET350T) or receives (NET350R) live video,
streams, lets you use computer networks to interface your control
data, and audio across existing Ethernet networks. Sending video
and monitoring stations with remote camera sites, whether they are
and audio over computer networks yields significant cost savings by
in the same building, across the country, or around the world.
using an existing computer network to monitor a remote site.
DataFAX
SPEC: 22907
C US
MANUAL: Not Vailable through DataFAX International Organization
® for Standardization;
C2907 / REVISED 3-04 Registered ISO 9001
Sect12.fm Page 360 Tuesday, May 4, 2004 8:38 AM
TECHNICAL SPECIFICATIONS
MODELS INTERFACES
NET350T Network video transmitter that encodes Video Input or Output 1, BNC, PAL/NTSC, 75 ohms, 1 Vp-p
video, audio, and control data for Audio Input/Output 3.5 mm stereo jack ring contact
transmission over an IP network LAN Interface Ethernet 10/100BaseT autosensing, RJ-45
NET350R Network video receiver that decodes video, LAN Data Rate 9.6 Kbps to 1.5 Mbps
audio, and control data received from an IP Data Interface 1 RS-232/RS-422/RS-485, bidirectional
network (9-pin, D-sub) and 1 RS-232 (9-pin, D-sub)
Alarm Input 1 terminal, 30 V maximum
Minimum PC Requirements (as needed) Alarm Output 1 terminal, 30 V, 1 A
• PC (Pentium® 4 microprocessor, 1.6 GHz) with Windows ®98/2000/XP
or higher operating system VIDEO
• 256 MB of RAM Video Standard PAL, NTSC
• Gateway to the network Video Image Size 704 x 576 pixels (high resolution)
• 100 Mbit Ethernet card 352 x 288 pixels (CIF)
• Sound card if using audio application
• Microsoft® Internet Explorer 6.0 (or higher), or free serial interface AUDIO
and terminal program, or PelcoNet NET350R (receiver) and video Input Voltage 1 Vp-p (line level)
monitor Input Impedance 50 kohm
• DirectX® 8.1 or 9.0 application programming interface Input Frequency Range 300 Hz - 10 kHz
• Screen resolution of 1024 x 768 or higher, 16- or 32-bit pixel color Audio Distortion <1%
resolution Audio Signal-to-Noise Ratio >50 dB (maximum)
• Graphic Card: ATI RADEON™ 7500 or 8500, Matrox G 550 or Maximum Output Voltage 2.5 Vp-p
Parhelia™, or NVIDIA® GeForce 3 or 4 with MPEG-4 playback Maximum Output Power RMS 60 mW
Output Impedance 8, 16, 32 ohms
capability
POWER
RELATED PRODUCTS Type Plug power adapter
NET300 Network video system that transmits Operating Voltage 12-24 VDC, power supply included
(NET300T) or receives (NET300R) live video Power Consumption Approximately 10 W
and control data across Ethernet networks.
Features dual MPEG-4 video streams.
NET4001A IP network video transmission system that MISCELLANEOUS
transmits and receives live video, audio, and LED Displays 5 LEDs (alarm, relay, connection, data, power)
control data across Ethernet networks.
Provides DVD quality video in MPEG-2 or
MPEG-4 format.
ENVIRONMENTAL
VMX300 Video management system that provides Operating Temperature 32° to 122°F (0° to 50°C)
control and monitoring of both analog and Operating Humidity 80% maximum relative humidity, non-
digital video systems. Supports client-to- condensing
server, client-to-multiple servers, and server- Storage Temperature- 4° to 140°F (-20° to 60°C)
to-server configurations. Storage Humidity 95% maximum relative humidity, non-
NVR300 Network video recorder that records video condensing
and audio over TCP/IP networks. Through its
Ethernet interface, it can receive compressed GENERAL
data generated by the PelcoNet NET300, Dimensions 5.6" W x 1.3" H x 5.3" D (14.3 x 3.3 x 13.5 cm)
NET350, and NET4001A. The NVR300 indexes Unit Weight Approximately 0.9 lb (0.4 kg) without power
the data and then transfers it to an internal supply
storage unit. Storage can be expanded Shipping Weight Approximately 2 lb (0.9 kg)
externally.
Spectra®, Esprit®, Genex®, and System 9760® are registered trademarks of Pelco.
PelcoNet™ and System 9740™ are trademarks of Pelco.
Microsoft®, Windows®, Internet Explorer®, and DirectX® are
registered trademarks of Microsoft Corporation.
Pentium 4® is a registered trademark of Intel Corporation.
®
CompactFlash is a registered trademark of SanDisk Corporation.
Pelco Worldwide Headquarters: NVIDIA® is a registered trademark of NVIDIA Corporation.
3500 Pelco Way, Clovis, California 93612-5699 USA ATI RADEON™ is a trademark of ATI Technologies Inc.
USA & Canada Tel: (800) 289-9100 • FAX (800) 289-9150 • DataFAX (800) 289-9108 Parhelia™ is a trademark of Matrox Technologies Inc.
International Tel: (559) 292-1981 • FAX (559) 348-1120 • DataFAX (559) 292-0435 Specifications subject to change without notice.
® www.pelco.com ©Copyright 2004, Pelco. All rights reserved.