1. Which of the following is the largest size drill?

A. A B. Z C. X D. XX
2. The size of the drill is stamped on the:
A. Point B. margin C. shank D. flute
3. In threaded members which of the following represent N.F ?
A. National file B. neutral file C. national fine D. not found
4. What tool used in precision work to smooth or enlarge holes?
A. Round out B. reamer C. drift pin D. protractor
5. Which of the following chisels would be used for cutting oil grooves?
6. Which of the following is not a cut of file?
A. Smooth B. half-round C. second cut D. bastrad
7. How do you call the tool used for cleaning files?
A. File cleaner B. file oilstone C. file card D. scraper
8. Which of the following is the smallest size drill?
A. #80 B. #1 C. #60 D. #0
9. In threaded member ,which of the following defines N.C ?
A. Neutral cut B. national cut C. national coarse D. not center
10. It is the ability of the material to resist loads that are applied suddenly and often at high velocity.
A. Fatigue strength B. impact strength C. hardness D. shock strength
11. A steel of carbon range of 0.05 to 0.3 percent is considered as what type of steel?
A. Low carbon steel C. high carbon steel
B. medium carbon steel D. vey high carbon steel
12. a steel of carbon range of 0.30 to 0.45 percent considered as what type of steel ?
A. low carbon steel C. high carbon steel
B. medium carbon steel D. alloyed steel
13. A steel of carbon range of 0.45 to 0.75 percent considered as what type of steel ?
A. low carbon steel C. high carbon steel
B. medium carbon steel D. alloyed steel
14. a steel of carbon range of 0.75 to 1.7 percent considered as what type of steel ?
A. low carbon steel C. high carbon steel
B. medium carbon steel D. very high carbon steel
15. Which of the following alloying elements of steel will tend to increase its strength without decreasing its toughness or
ductility and with its large quantities the steel become tough but develop high resistance to corrosion and shock?
A. Chromium B. manganese C. molybdenum D. nickel
16. A white metal , almost as bright as silver and is malleable and ductile and can be welded.
A. Nickel B. aluminum C. white iron D. lead
17. It is a silvery dull, soft metal and second lightest of all metals used in industry.
A. Nickel B. Aluminum C. white iron D. lead
18. The least among iron ores for it contains many impurities , poor in iron content and commonly used in England.
A. Hematite B. magnetite C. limanite D. siderite
19. Which of the following is not considered to be precious metal?
A. Silver B. gold C. platinum D. steel
20. It is an alloy of copper and zinc . it is approximately 1/3 zinc and 2/3 copper.
A. Brass B. bronze C. munts metal D. silver
21. A white metal , almost as bright as silver and is malleable and ductile and can be welded
A. Nickel B. aluminum C. white iron D. lead
22. It is a silvery dull, soft metal and second lightest of all metals used in industry.
B. Nickel B. Aluminum C. white iron D. lead
23. The least among iron ores for it contains many impurities , poor in iron content and commonly used in England.
B. Hematite B. magnetite C. limanite D. siderite
24. Which of the following is not considered to be precious metal?
B. Silver B. gold C. platinum D. steel
25. It is an alloy of copper and zinc . it is approximately 1/3 zinc and 2/3 copper.
A. Brass B. bronze C. munts metal D. silver
26. It is the element whose chief function is to strengthen the ferrite . it is used wiyh tungsten to develop red
hardness or ability to remain hard when red hot.
A. Chromium B. cobalt C. molybdenum D. nickel
27. The ability of a material to resist loads that are applied suddenly and often at high velocity.
A. Fatigue strength
B. Bending strength
C. Comprehensive strength
D. Impact strength
28. The ability of the material to stretch , bend, or twist without breaking or cracking .
A. Ductility B. malleability C. hardness D. compressibility
29. Which of the following is considered to be the father of all machine tool?
A. Lathe machine B. boring machine C. drilling machine D. milling machine
30. If you wanted to check the face of pump slide valve or other flat –faced valve , oyu could check for trueness
on a :
 A. Flat board B. piece of glass C. surface plate D. bearing plate
31. It is a copper tin alloy and is named either bell metal or brown metal.
A. Brass B. bronze C. munts metal D. silver
32. It is furnace that converts pig iron into steel by oxidizing out the surplus carbon and using oxygen by throwing row iron
ore into the furnace.
A. Open-hearth furnace B. electric furnace C. cupola D. Bessemer
33. The most commonly used series in the bulk production of bolts ,screws , nuts and other general applications in the
coarse-thread series .
A. UNC B. UNF C. white iron D. lead
34. What is the actual torque ratio of a gear set deliver by its gear ratio?
A. Approach ratio B. clearance C. contact ratio D. efficiency
35. Which of the following has lo coefficient of expansion ,corrosion resist ant , weak in strength , and used for non-ferrous
applications as an alloying element?
A. Aluminum B. aluminum oxide C. copper oxide D. copper
36. Which of the following is abundant for ferrous metals?
A. Sulfur B. phosphorus C. manganese D. Carbon
37. What machine is used to flatten surface on a vertical , horizontal or even angular plane?
A. Shaper machine B. power saw C. boring machine D. drilling machine
38. All of these are classifications of ore; except what?
A. Magnetite B. hematite C. siderite D. Sulfurite
39. It refers to the internal resistance of a material to being deformed and is measured in terms of the applied load.
A. Stress B. strain C. ductility D. malleability
40. The property of a material which resist forecasting to pull the material apart.
A. Tensile strength C. bending strength
B. comprehensive strength D. torsional strength
41. The property of a material which resist forces from causing a member to bend or deflect in the direction in which the
load is applied.
A. Bending strength C. Tensile strength
B. Comprehensive strength D. Torsional strength
42. It is the element whose chief function is to strengthen the ferrite . it is used wiyh tungsten to develop red hardness or
ability to remain hard when red hot.
B. Chromium B. cobalt C. molybdenum D. nickel
43. It is also known as a strain drawing it is the process whereby certain degree of hardness is sacrificed in order to reduce
brittleness and increase the toughness of steel tool.
A. Tempering B. normalizing C. annealing D. quenching
44. It is the heat treatment of steel that produced extremely hard surface . the process consist of exposing the steel to hot
ammonia gas for some hours?
A. Nitriding B. cyaniding C. carburizing D. ammonia bath
45. How do you call the metals that contains large amount of carbon content .
A. Ferrous metal B. non-ferrous metal C. base metals D. precious metals
46. All of these are the basic kinds of cast iron , except:
A. Gray iron B. malleable iron C. white iron D. red iron
47. Which of the following basic kind of cast iron is harder and more difficult to machine because it contains carbon in
carbide state?
A. Gray iron B, malleable iron C. white iron D. wrought iron
48. Which of the following alloying elements of steel will produce the greatest hardening effect like carbon and at the same
time reduce the enlargement of its grain structure.
A. Chromium B. manganese C. molybdenum D. nickel
49. Which of the following alloying elements of steel will produce fine grain structure and promotes greater toughness and
ductility?
A. Chromium B. manganese C. molybdenum D. nickel
50. Whish of the following alloying elements of steel which makes it extremely hard and resistance to wear without
making brittle?
A. Chromium B. Manganese C. Molybdenum D. nickel
51. It is the element used mostly in steels designed for metal cutting tools. The steels added by this element are tough , hard
and very resistant to wear.
A. Chromium B.tungsten C. molybdenum D. nickel
52. A steel numbered SAE-AISI, C1035 when not rolled and contains 0.60% to 1.30% carbon and used when extra hardness is
required.
A. Low carbon steel C. high carbon steel
B. Medium carbon steel D. very high carbon steel
53. Which of the following alloying elements used in making high speed steel?
A. Molybdenum B. nickel C. manganese D. silicon
54. Which of the following alloying elements used in springs to make reliant.
A. Silicon B. tungsten C. hardness and resistance D. nickel
55. It refers to that property in steel which resist indention or penetration . it is usually expressed in forms of the area of an
indention made by a special ball under standard load , or the depth of a special indentor.
A. Hardness B. ductility C. malleability D. wear of resistance
56. The distance from point on a screw thread to the corresponding point on an adjacent thread , measured parallel to the
axis.
 A. Pitch B. crest C. lead D. thread
57. If you wanted to check the face of pump slide valve or other flat –faced valve , oyu could check for trueness on a :
B. Flat board B. piece of glass C. surface plate D. bearing plate
58. Which of the following is used to keep a metal clean while soldering?
A. Flax B. flux C. torch D. insulated
59. Before splicing electric wires ,they should be:
A. Tinned B. soldered C. cleaned and tinned D. insulated
60. To check the speed of a motor or other rotary machine , one would use a :,
A. Galvanometer B. tachometer C. micrometer D. Geiger counter
61. Before drilling a hole in a piece of metal , it should be ;
A. Mark with chalk B. scribed C. center-punched D. protracted
62. The top of the surface joining the two sides of a thread
A. Pitch B. crest C. lead D. space
63. The amount of variation permitted in the size of a part. It is the difference between the limit of the maximum and
minimum dimension of a given part . it may be expressed at plus , minus , or as both plus and minus.
A. Tolerance B. limits C. variation d. clearance
64. The instrument used to reshape a grinding wheel that is grooved or out of round is called
A. Wheel aligner B. wheel emery C. wheel dresser D. wheel cutter
65. The instrument used to remove old packing from packing glands and stuffing boxes are called
A. Packing tools B. gland box cleaners C. packing bits D. packing screws
66. When working on bearings and checking for spots ,it is customary to apply what?
A. White lead B. dykem blue C. red lead D. Prussian blue
67. A classification of iron ore which contain 70% iron when pure and 50 % iron when mined.
A. Hematite B. magnetite C. limanite D. siderite
68. A classification of iron ore which contains 72.5 % when pure and the remaining percentage are impurities.
A. Hematite B. magnetite C. limanite D. siderite
69. Which of the following iron ore also known as ‘’brown hematite’’or ferric oxide a yellowish brown powder?
A. Hematite B. magnetite C. limanite D. siderite
70. Which of the following represents manganese steel?
A. 13xx B. 40xx C. 50xx D. 10xx
71. It is another kind of furnace where cast iron is remelted to make into cast iron . the furnace is charge with layers of coke
and pig iron plus scrap iron.
A. Open-hearth furnace B. electric furnace C. cupola D. Bessemer
72. A furnace which consist of blowing a stream of air through a molten mass of iron pig. A stream of air is turned on
through the wind box and enters the converter at the bottom . manganese , carbon and other elements of varying
amounts are added to produced steel which is then poured and solidifies.
A. Open-hearth furnace B. electric furnace C. cupola D. bessemers
73. Which of the following is abundant for ferrous metals?
A. Sulfur B. phosphorus C. manganese D. Carbon
74. What machine is used to flatten surface on a vertical , horizontal or even angular plane?
A. Shaper machine B. power saw C. boring machine D. drilling machine
75. All of these are classifications of ore; except what?
A. Magnetite B. hematite C. siderite D. Sulfurite
76. It refers to the internal resistance of a material to being deformed and is measured in terms of the applied load
A. Stress B. strain C. ductility D. malleability
77. The property of a material which resist forecasting to pull the material apart.
A. Tensile strength C. bending strength
B. comprehensive strength D. torsional strength
78. The property of a material which resist forces from causing a member to bend or deflect in the direction in which the
load is applied.
A. Bending strength C. . Tensile strength
B. Comprehensive strength D. Torsional strength
79. A tap or die marked ¼ -20 indicates:
A. ¼ nradius -20 cm. long C. ¼ nradius -20 threads per in.
n
B. ¼ diameter -20 threads per in. D. ¼ nturn -20 times
80. After a piece ofpipe has cut , the hole is cleaned out with a:
A. Pipe reamer B. pipe taper C. pipe cleaner D. hole cleaner
81. How do you call the tool(s)used for cutting pipe threads?
A. Pipe cutter B. pipe threader C. pipe stock and die D. pipe ratcher cutter
82. How do you call the tool used when working with larger size of pipe?
A. Chain pipe wrench B. chain holder C. chain tongs D. A and B
83. What tool is used when preparing to put fittings on copper tubing ?
A. Tube spreader B. tube retarder C. flaring tool D. tube countersink
84. A steel numbered SAE-AISI, C1035 when not rolled and contains 0.60% to 1.30% carbon and used when extra
hardness is required.
A. Low carbon steel C. high carbon steel
C. Medium carbon steel D. very high carbon steel
85. Which of the following alloying elements used in making high speed steel?
A.Molybdenum B. nickel C. manganese D. silicon
86. Which of the following alloying elements used in springs to make reliant.
 A.Silicon B. tungsten C. hardness and resistance D. nickel
87. It refers to that property in steel which resist indention or penetration . it is usually expressed in forms of the area of
an indention made by a special ball under standard load , or the depth of a special indentor.
A. Hardness B. ductility C. malleability D. wear of resistance
88. The distance from point on a screw thread to the corresponding point on an adjacent thread , measured parallel to
the axis.
A. Pitch B. crest C. lead D. thread
89. A classification of iron ore which contain 70% iron when pure and 50 % iron when mined.
A.Hematite B. magnetite C. limanite D. siderite
90. A classification of iron ore which contains 72.5 % when pure and the remaining percentage are impurities.
A.Hematite B. magnetite C. limanite D. siderite
91. Which of the following iron ore also known as ‘’brown hematite’’or ferric oxide a yellowish brown powder?
A.Hematite B. magnetite C. limanite D. siderite
92. Which of the following represents manganese steel?
A.13xx B. 40xx C. 50xx D. 10xx
93. It is another kind of furnace where cast iron is remelted to make into cast iron . the furnace is charge with layers of
coke and pig iron plus scrap iron.
A.Open-hearth furnace B. electric furnace C. cupola D. Bessemer
94. A furnace which consist of blowing a stream of air through a molten mass of iron pig. A stream of air is turned on
through the wind box and enters the converter at the bottom . manganese , carbon and other elements of varying
amounts are added to produced steel which is then poured and solidifies.
A.Open-hearth furnace B. electric furnace C. cupola D. bessemers
95. What machine is used to flatten surface on a vertical , horizontal or even angular plane?
A.Shaper machine B. power saw C. boring machine D. drilling machine
96. All of these are classifications of ore; except what?
A.Magnetite B. hematite C. siderite D. Sulfurite
97. It refers to the internal resistance of a material to being deformed and is measured in terms of the applied load.
A.Stress B. strain C. ductility D. malleability
98. The property of a material which resist forecasting to pull the material apart.
A.Tensile strength B. comprehensive strength
C.bending strength D. torsional strength
99. The property of a material which resist forces from causing a member to bend or deflect in the direction in which the
load is applied.
A.Bending strength B. Comprehensive strength
C.Tensile strength D. Torsional strength
100.The least among iron ores for it contains many impurities , poor in iron content and commonly used in England.
A.Hematite B. magnetite C. limanite D. siderite