Dell EMC NetWorker

Version 18.1

VMware Integration Guide

302-004-429
REV 07
Copyright © 1990-2019 Dell Inc. or its subsidiaries. All rights reserved.

Published February 2019

Dell believes the information in this publication is accurate as of its publication date. The information is subject to change without notice.

THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS-IS.“ DELL MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND
WITH RESPECT TO THE INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. USE, COPYING, AND DISTRIBUTION OF ANY DELL SOFTWARE DESCRIBED
IN THIS PUBLICATION REQUIRES AN APPLICABLE SOFTWARE LICENSE.

Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be the property of their respective owners.
Published in the USA.

Dell EMC
Hopkinton, Massachusetts 01748-9103
1-508-435-1000 In North America 1-866-464-7381
www.DellEMC.com

2 NetWorker 18.1 VMware Integration Guide

CONTENTS

Figures 9

Tables 13

Preface 15

Chapter 1 Introduction to NetWorker VMware Protection with the vProxy

appliance 21
Introduction to NetWorker VMware Protection with vProxy appliance...... 22
Components in the NetWorker VMware Protection Solution with vProxy
appliance.................................................................................................... 22
System requirements..................................................................................23
Port requirements...................................................................................... 25
vProxy limitations and unsupported features.............................................. 27
Compatibility information........................................................................... 30
Recommendations and considerations........................................................30
Performance and scalability...........................................................30
NetWorker VMware Protection Solution best practices with the
vProxy appliance........................................................................... 32
Configuration checklist..................................................................35
Accessing Knowledge Base Articles............................................................36

Chapter 2 Deploy the vProxy appliance and configure the NetWorker

datazone 37
Deploying the vProxy appliance.................................................................. 38
Deploy the vProxy OVA on a vCenter server................................. 38
Deploy the vProxy OVA on an ESXi host....................................... 39
VMware vCenter server management......................................................... 41
Add the vCenter server using NMC's VMware View.......................41
Add the vCenter server using the NetWorker Management Web UI..
42
Configuring and registering the vProxy appliance.......................................44
Configure and register the vProxy in NMC.................................... 44
Add and configure the vProxy in the NetWorker Management Web
UI...................................................................................................46
Installing the vCenter plug-in...................................................................... 47
Install the vCenter plug-in using VMware View in NMC................. 47
Install the vCenter plug-in using the NetWorker Management Web
UI.................................................................................................. 50
Enable the Microsoft VM App Agent for SQL Server application-consistent
protection................................................................................................... 51
Additional vProxy backup configuration options......................................... 56
Configure a backup to support VMware encryption....................... 57
Configure a backup to support vSAN encryption........................... 58
Enabling or disabling Changed Block Tracking............................... 58

NetWorker 18.1 VMware Integration Guide 3

CONTENTS

Creating a dedicated vCenter user account and VM Backup and Recovery

role............................................................................................................. 59
Create vCenter user account.........................................................59
Create a customized role............................................................... 60
vSphere Client user accounts........................................................ 63
Adding a NIC for VMXNET 3 on the vProxy appliance................................ 65
Dual vNIC setup and configuration requirements........................................68
Verify vNIC connectivity............................................................................ 69
Migrating policies from VMware Backup appliance to vProxy appliance..... 70
Co-existence of the VMware Backup appliance and vProxy
appliance........................................................................................ 71
Migration pre-requisites.................................................................73
Policy migration to vProxy by using NMC...................................... 73
Policy migration to vProxy by using the command line...................74
Renaming a NetWorker 9.1 and later server with legacy VMware
Backup appliance........................................................................... 75
Updating the Microsoft VM App Agent and FLR Agent software................75
Updating the vProxy appliance................................................................... 75
Deleting the vProxy host ........................................................................... 76
Redeploying a vProxy................................................................................. 77
Un-registering and re-registering a vProxy after removal........................... 77
Resetting the admin account password ..................................................... 77

Chapter 3 Protecting virtual machines 79

Preparing the NetWorker data zone........................................................... 80
Configure the Data Domain System...............................................80
Creating VMware data protection policies in NMC for the vProxy appliance..
81
Overview of data protection policies.............................................. 81
Create a VMware policy.................................................................83
Creating a workflow.......................................................................84
Create or edit a VMware group......................................................89
VMware actions............................................................................. 91
Starting, stopping, and restarting policies.....................................101
Enabling a VMware group with Dynamic Association and applying
rules in NMC................................................................................. 101
Visual representation of VMware policy and associated actions... 105
VMware View in NMC.................................................................. 106
vProxy backup workflows in the vSphere Client's Dell EMC NetWorker
interface.................................................................................................... 112
Connect to the NetWorker server in the vSphere Client............... 112
Start a vProxy policy in the vSphere Client Dell EMC NetWorker
interface....................................................................................... 115
Add virtual machines to a vProxy policy in the vSphere Client Dell
EMC NetWorker interface............................................................ 116
vProxy workflows in the vSphere Web Client's VM Backup and Recovery
interface.................................................................................................... 118
Connect to the NetWorker server in the vSphere Web Client.......118
Starting a vProxy policy in the vSphere Web Client..................... 120
Adding virtual machines to a vProxy policy workflow in the vSphere
Web Client.................................................................................... 121
Troubleshooting Data Protection Policies................................................. 122
Backup operations........................................................................122
vProxy backup log files.................................................................126
NMC function to collect vProxy log bundle information............... 127

4 NetWorker 18.1 VMware Integration Guide

 CONTENTS

Logs for SQL application-consistent data protection................... 128

Chapter 4 Recover virtual machines and data 129

vProxy recovery in NMC........................................................................... 130
Entering management credentials for the Data Domain resource
(instant recovery and User mode file-level restore only).............. 130
File-level restore as a domain user................................................132
Recovering a virtual machine using the NMC Recovery wizard.... 134
vProxy recovery in the NetWorker Management Web UI.......................... 151
Revert (or rollback) a virtual machine backup.............................. 152
Recover to a new virtual machine.................................................153
Instant Restore of a virtual machine.............................................154
Virtual Disk (VMDK) recovery...................................................... 155
Emergency Recovery................................................................... 156
File Level recovery....................................................................... 158
Monitor recovery operations in the NetWorker Management Web UI
.....................................................................................................159
vProxy file-level restore and SQL restore in the Dell EMC Data Protection
Restore Client........................................................................................... 159
Pre-requisites for file-level restore and SQL restore.................... 160
File-level restore and SQL restore limitations...............................169
Using the Dell EMC Data Protection Restore Client for file-level
restore and SQL restore............................................................... 172
vProxy recovery in the vSphere Client's Dell EMC NetWorker interface...186
Connect to the NetWorker server in the vSphere Client.............. 186
Recovery to the original virtual machine.......................................189
Recovery to a new virtual machine............................................... 191
Virtual disk recovery (restore to an existing virtual machine)....... 193
Instant recovery of a virtual machine........................................... 195
vProxy recovery in the vSphere Web Client's VM Backup and Recovery
interface....................................................................................................197
Connect to the NetWorker server in the vSphere Web Client...... 198
Recovery to the original virtual machine.......................................199
Recovery to a new virtual machine...............................................201
Virtual disk recovery.................................................................... 202
Instant recovery of a virtual machine...........................................203
vProxy recovery log files.......................................................................... 205

Chapter 5 NetWorker VMware Protection with the VMware Backup

Appliance (legacy) 207
Introduction to NetWorker VMware Protection with the VMware Backup
appliance (legacy).................................................................................... 208
NetWorker VMware Protection tasks for the VMware Backup appliance. 208
System requirements............................................................................... 209
Port requirements......................................................................................211
Download and deploy the VMware Backup appliance................................ 214
Pre-installation requirements....................................................... 214
Downloading the OVAs for the VMware Backup appliance........... 216
Proxy assignment for backup and recovery.................................. 217
Deploy the VMware Backup appliance.......................................... 217
Deploy external proxy appliance in vCenter..................................219
Upgrade the VMware Backup Appliance and vCenter.................. 223
Creating a dedicated vCenter user account and VM Backup and Recovery
role........................................................................................................... 230

NetWorker 18.1 VMware Integration Guide 5

CONTENTS

Create vCenter user account.......................................................230

Create a customized role..............................................................231
vSphere Client user accounts...................................................... 233
Restrict mapping of datastores................................................................ 235
EMC Backup and Recovery Configuration Utility......................................235
Post-installation configuration..................................................................240
Starting and stopping services..................................................... 241
Changing the maintenance window............................................. 242
Adding or swapping a NIC for VMXNET 3 on the VMware Backup appliance
or external proxy...................................................................................... 243
Dual NIC support...................................................................................... 246
Dual vNIC setup and configuration requirements......................... 247
Verify vNIC connectivity...........................................................................248
Backing up the VMware environment using NMC.....................................249
Setting user privileges for the root user in the NetWorker server....
249
Accessing VMware Protection in NMC........................................250
VMware Backup Appliance monitoring and properties..................251
VMware data protection policies for the VMware Backup appliance
in NMC........................................................................................ 252
Decommissioning the VMware Backup Appliance in NMC........... 260
Managing the VMware environment using the vSphere Web Client......... 260
Benefits of EMC Backup and Recovery user interface in the
vSphere Web Client.....................................................................260
Deduplication store benefits.........................................................261
Image-level Backup and Restore.................................................. 261
Connecting to the EMC Backup and Recovery user interface in the
vSphere Web Client..................................................................... 262
Available tasks in the EMC Backup and Recovery user interface
(VMware Backup Appliance only)................................................ 263
Assigning virtual machines/VMDKs to a backup.......................... 273
Manually starting a workflow by using Backup Now.....................275
Stopping a workflow.................................................................... 275
Viewing workflow progress.......................................................... 275
Restoring the VMware environment......................................................... 276
FULLVM (Image-level) Restore................................................... 276
File-level restore.......................................................................... 282
Monitoring EMC Backup and Recovery activity........................................289
Viewing Recent Tasks in the vSphere Web Client........................290
Viewing Alarms............................................................................ 290
Viewing the Event Console...........................................................291
Shutdown and Startup Procedures...........................................................292
EMC Backup and Recovery Capacity Management.................................. 292
Impact of selecting thin or thick provisioned disks.......................292
Save set lifecycle.........................................................................293
Checkpoints and VMware Backup Appliance rollback............................... 293
Creating a checkpoint using the EMC Backup and Recovery user
interface...................................................................................... 294
Rolling back to a checkpoint........................................................ 294
Protecting checkpoints for the VMware Backup appliance..........295
Cross Sync............................................................................................... 295
Disaster Recovery.................................................................................... 296
Disaster Recovery Guidelines...................................................... 296
Disaster recovery without checkpoint..........................................297
Preparing the VMware Backup appliance for disaster recovery... 298

6 NetWorker 18.1 VMware Integration Guide

 CONTENTS

Performing a disaster recovery of the VMware Backup Appliance....

299
Complete disaster recovery of the VMware Backup Appliance and
the Data Domain or tape device...................................................300
Recovery from a secondary site.................................................. 302
Best practices and troubleshooting.......................................................... 303
Performance and scalability.........................................................303
VMware Backup Appliance best practices................................... 305
Limitations and unsupported features..........................................308
Configuration checklist................................................................ 310
IPv6 considerations.......................................................................311
VMware Backup Appliance installation.......................................... 311
AV-NetWorker Communicator (avnwcomm) timeout...................312
Log in to the EMC Backup and Recovery Console as admin instead
of root.......................................................................................... 312
Launching the Dell EMC Data Protection Restore Client after
upgrade on Mozilla Firefox browser..............................................313
Launching the EMC Backup and Recovery Configuration Utility
after upgrade on Mozilla Firefox browser..................................... 313
Restart the Enterprise Manager Web Application (emwebapp)....314
VMware Backup Appliance Log file locations................................314
NetWorker operations..................................................................315
vCenter server operations............................................................ 316
vSphere Client operations............................................................ 317
Backup operations........................................................................319
Restore operations....................................................................... 321
Adding external proxies................................................................322
Creating and analyzing crashes on Windows 2008 R2................. 322
Changing the Data Domain Boost password................................ 323
Accessing Knowledge Base Articles............................................. 323

Chapter 6 VADP Recovery (legacy) 325

Software and hardware requirements.......................................................326
Limitations and unsupported features.......................................................327
Limitations to vCenter on non-English versions of Windows........ 327
Limitation for VADP proxy host on non-English versions of Windows
.................................................................................................... 327
Transport modes...................................................................................... 328
Independent persistent disks cannot be recovered...................................328
Configuring the VADP proxy host and Hypervisor resource......................329
Creating a Hypervisor resource from the NetWorker server........329
Creating a NetWorker client for the VADP Proxy host by using the
Client properties windows........................................................... 330
Creating a VADP User role in vCenter....................................................... 331
Creating a VADP Proxy role..........................................................331
Assigning the VADP User role to the user specified in the
NetWorker Hypervisor resource.................................................. 332
Minimum vCenter permissions needed to recover using VADP.... 332
Recovering VADP Backups....................................................................... 334
File based recovery of a VM.........................................................334
Image level (single step) recovery of a full VM............................ 336
VADP Planning and Best Practices............................................................341
Recommendations and considerations for VADP recovery........... 341
Selection of physical vs. virtual proxy...........................................341
Recommendations for Data Domain systems............................... 342

NetWorker 18.1 VMware Integration Guide 7

CONTENTS

Network and Firewall port requirements...................................... 343

Support for tape drives in a virtual machine.................................344
Recommendations and considerations for transport modes.........345
VADP proxy access to LUNs........................................................ 347

Appendix A NetWorker VMware Protection in VMware Cloud on Amazon Web

Services 349
Introduction to NetWorker VMware Protection in VMware Cloud on AWS....
350
Prerequisites............................................................................................ 350
Deploy the vProxy OVA on a vCenter server in VMware Cloud on AWS... 352
NetWorker VMware Protection for VMware Cloud on AWS best practices....
354
Unsupported NetWorker operations.........................................................355

Appendix B Regular expressions for NetWorker vProxy dynamic policies rule

definitions 357
Regular expression syntax accepted by dynamic policy rule definition..... 358

Glossary 363

8 NetWorker 18.1 VMware Integration Guide

FIGURES

1 Components in a NetWorker VMware Protection Solution ........................................ 22

2 Port requirements for NetWorker VMware Protection with the vProxy appliance......26
3 Install vCenter Plugin in NMC.....................................................................................48
4 vCenter plug-in for Dell EMC NetWorker in the vSphere Client..................................48
5 vCenter plug-in for Dell EMC NetWorker in the vSphere Client.................................. 51
6 Hosts and Clusters in the vSphere Web Client........................................................... 64
7 Swap network for NICs in the Virtual Machine Properties window............................. 65
8 Change Adapter Type.................................................................................................66
9 Routing table with backup network gateway.............................................................. 67
10 Backup and production traffic with dual network adapters.........................................69
11 Migrating a VMware Backup appliance policy to vProxy in NMC................................ 74
12 Migrate Operation Results dialog................................................................................74
13 Data Protection Policy................................................................................................82
14 Platinum policy configuration..................................................................................... 83
15 Changing the Backup Optimization mode in the vProxy protection group...................91
16 Specify vProxy Options page......................................................................................94
17 Create a new rule to apply to a VMware group..........................................................104
18 VMware protection policy in the Protection window................................................. 105
19 VMware protection policy save sets in Media window...............................................106
20 Add a vCenter server to VMware View in NMC.........................................................106
21 Map view of VMware environment in NMC............................................................... 108
22 Cluster with child elements in VMware View............................................................. 109
23 Filtering results in VMware View................................................................................110
24 VMware table view.................................................................................................... 110
25 Add group in VMware View.........................................................................................111
26 Accessing Dell EMC NetWorker in the vSphere Client............................................... 113
27 NetWorker connection information in the vSphere Client.......................................... 113
28 Dell EMC NetWorker Basic Tasks pane......................................................................114
29 Policies pane with available vProxy policies............................................................... 115
30 Policy backup options................................................................................................ 116
31 Recent Tasks pane.....................................................................................................116
32 Policies pane with available vProxy policies................................................................117
33 Edit a vProxy policy................................................................................................... 117
34 Backup sources in the Editing backup policy dialog....................................................118
35 NetWorker connection information in the vSphere Web Client..................................119
36 Backup pane with vProxy policy.................................................................................121
37 Backup sources in the Editing backup policy window................................................ 122
38 NSR Data Domain Properties..................................................................................... 131
39 Add Domain FLR user................................................................................................ 133
40 Virtual machine recovery in the NMC Recovery wizard.............................................134
41 Select the Virtual Machine to Recover...................................................................... 135
42 Select the Target Backup (individual virtual machine)...............................................136
43 Select the Target Backup (multiple virtual machines)............................................... 136
44 Select the Virtual Machine Recovery method........................................................... 136
45 Choose Disks to Revert............................................................................................. 138
46 Select Alternate Recovery Sources...........................................................................139
47 Configure the Instant Recovery................................................................................ 140
48 Configure the virtual machine recovery.....................................................................142
49 Configure the Virtual Disk Recovery..........................................................................143
50 Configure the Emergency Recovery..........................................................................145
51 Select Alternate Recovery Sources for file level recovery......................................... 147
52 Mount the save set for file level recovery................................................................. 148
53 Select the files and folders to recover.......................................................................149

NetWorker 18.1 VMware Integration Guide 9

FIGURES

54 NSR Data Domain Properties.................................................................................... 163

55 Add Domain FLR user................................................................................................165
56 Manage Authentication service users........................................................................166
57 Application Administrators user group properties ..................................................... 167
58 VMware FLR Users user group properties................................................................. 167
59 Deploy FLR Agent if not found ................................................................................. 168
60 Select backups to restore from................................................................................. 174
61 Select restore location.............................................................................................. 174
62 Select items to restore.............................................................................................. 175
63 Restore Monitoring................................................................................................... 176
64 Select the backup(s) to restore from........................................................................ 177
65 Select restore location.............................................................................................. 178
66 Select items to restore.............................................................................................. 179
67 Total items available for recovery..............................................................................179
68 Restore Monitoring................................................................................................... 180
69 Select App Backups page.......................................................................................... 183
70 Restore Target page................................................................................................. 183
71 Restore Options page............................................................................................... 185
72 Restore Monitoring................................................................................................... 186
73 Accessing Dell EMC NetWorker in the vSphere Client.............................................. 187
74 NetWorker connection information in the vSphere Client......................................... 187
75 Dell EMC NetWorker Basic Tasks pane..................................................................... 188
76 Restore pane with available virtual machine backups................................................ 189
77 Select Restore from the Action drop-down...............................................................190
78 Restore to original location....................................................................................... 190
79 Restore pane with available virtual machine backups................................................. 191
80 Select Restore from the Action drop-down...............................................................192
81 Restore to new virtual machine................................................................................. 192
82 Restore pane with available virtual machine backups................................................ 193
83 Select Restore from the Action drop-down...............................................................194
84 Restore virtual disks to existing virtual machine........................................................ 194
85 Restore pane with available virtual machine backups................................................ 196
86 Select Restore from the Action drop-down...............................................................196
87 Instant Restore..........................................................................................................197
88 NetWorker connection information in the vSphere Web Client................................. 198
89 Virtual machines for recovery in the Restore pane................................................... 200
90 Select a restore point............................................................................................... 200
91 Restore to original location.......................................................................................200
92 Restore options for the new virtual machine recovery.............................................. 201
93 Select VMDK backup to restore............................................................................... 202
94 Set Restore Options for VMDK recovery..................................................................203
95 Set Instant Access restore options........................................................................... 204
96 Finish Instant Access recovery................................................................................. 205
97 Firewall configuration (VMware Backup appliance with internal proxy).....................212
98 Firewall configuration (VMware Backup appliance with external proxy)....................213
99 Selecting the OVA to deploy in vCenter/vSphere Web Client................................... 218
100 EMC Backup and Recovery registration ................................................................... 219
101 Registering proxy with the VMware Backup appliance..............................................222
102 Select vCenter registration in the EMC Backup and Recovery Configuration Utility.224
103 vCenter Configuration in the EMC Backup and Recovery Configuration Utility........ 224
104 Upgrading order for NetWorker components when upgrading the VMware Backup
appliance.................................................................................................................. 226
105 Take Snapshot in vSphere Client.............................................................................. 227
106 Connect to ISO in vSphere Client............................................................................. 228
107 Accessing online help during upgrade....................................................................... 228
108 Hosts and Clusters in the vSphere Web Client..........................................................234

10 NetWorker 18.1 VMware Integration Guide

 FIGURES

109 Welcome configuration page.................................................................................... 236

110 Network Settings configuration page....................................................................... 237
111 Time Zone configuration page...................................................................................237
112 EBR Credentials configuration page......................................................................... 238
113 vCenter Registration configuration page.................................................................. 238
114 NetWorker registration configuration page.............................................................. 239
115 Complete configuration page....................................................................................240
116 Complete progress page...........................................................................................240
117 Post VMware Backup Appliance configuration.......................................................... 241
118 Swap network for NICs in the Virtual Machine Properties window........................... 244
119 Change Adapter Type...............................................................................................245
120 Routing table with production network gateway.......................................................246
121 Sample backup and production network traffic flow................................................. 247
122 NMC Enterprise window...........................................................................................250
123 Protection window in the Administration window..................................................... 250
124 VMware Backup appliance health monitoring in the Devices window........................ 251
125 NSR VBA Server Properties window......................................................................... 251
126 VMware protection policy in the Protection window................................................ 254
127 VMware protection policy save sets in Media window.............................................. 254
128 Map view of VMware environment in NMC.............................................................. 256
129 Cluster with child elements in VMware View.............................................................257
130 Filtering results in VMware View...............................................................................257
131 VMware table view................................................................................................... 258
132 Add group in VMware View.......................................................................................259
133 Selecting the Backup Appliance................................................................................263
134 EMC Backup and Recovery user interface in the vSphere Web Client......................264
135 VMware Backup Appliance Backup tab.....................................................................265
136 VMware Backup Appliance Restore tab.................................................................... 266
137 VMware Backup appliance Reports tab.................................................................... 266
138 VMware Backup Appliance Configuration tab........................................................... 268
139 Log view .................................................................................................................. 270
140 Email configuration view............................................................................................271
141 Run Integrity Check option....................................................................................... 273
142 Selecting virtual machines in the Editing backup policy wizard................................. 274
143 Viewing workflow progress in the Task Console....................................................... 276
144 Restore tab in EMC Backup and Recovery user interface......................................... 277
145 Select a backup........................................................................................................ 279
146 Set instant access options........................................................................................280
147 Ready to complete................................................................................................... 280
148 Emergency Restore window..................................................................................... 282
149 EMC Data Protection Restore Client User Login...................................................... 284
150 Select the backups to restore from page..................................................................285
151 Select items to restore page.....................................................................................286
152 Select destination to restore to page........................................................................286
153 Accessing the restore monitor.................................................................................. 287
154 Restore Monitor panel.............................................................................................. 287
155 EMC Data Protection Restore Client Admin Login....................................................288
156 Select and log in to the destination client................................................................. 288
157 Accessing the restore monitor..................................................................................289
158 Restore Monitor panel.............................................................................................. 289
159 Running an integrity check....................................................................................... 294
160 Roll back to checkpoint............................................................................................ 295
161 Networker registration during new appliance configuration......................................298
162 Starting a VMware Backup Appliance disaster recovery...........................................300
163 Starting a VMware Backup Appliance disaster recovery........................................... 301
164 Entering appliance credentials.................................................................................. 302

NetWorker 18.1 VMware Integration Guide 11

FIGURES

165 Apps and Modules tab in NMC.................................................................................. 331

166 Recover Options dialog.............................................................................................335
167 VMware vCenter restore.......................................................................................... 338
168 Enable internet access for Forwarders..................................................................... 352
169 Add a vCenter Server to VMware View with Deployed in Cloud enabled...................354
170 NSR VMware Proxy Properties................................................................................ 355

12 NetWorker 18.1 VMware Integration Guide

TABLES

1 Revision history...........................................................................................................15
2 Style conventions........................................................................................................18
3 NetWorker VMware Protection with vProxy appliance requirements......................... 24
4 Incoming port requirements........................................................................................25
5 Outgoing port requirements....................................................................................... 26
6 Performance and scalability factors........................................................................... 30
7 MSVMAPPAGENT binaries called by vProxy..............................................................52
8 Supported characters in SQL database names........................................................... 55
9 Minimum required vCenter user account privileges ................................................... 60
10 Supported and unsupported VMware Backup appliance operations in a NetWorker 9.1
and later environment..................................................................................................71
11 Schedule icons........................................................................................................... 93
12 Schedule icons........................................................................................................... 98
13 Backup log files......................................................................................................... 126
14 FLR privilege requirements........................................................................................ 161
15 Recovery log files..................................................................................................... 205
16 NetWorker VMware Data Protection tasks...............................................................208
17 NetWorker VMware Protection requirements........................................................... 210
18 Incoming port requirements....................................................................................... 211
19 Outgoing port requirements — with external proxies................................................212
20 Recommended memory and swap space based on storage space utilization............. 216
21 Minimum required vCenter user account privileges .................................................. 231
22 Description of services running on the VMware Backup Appliance............................241
23 Backup tab column descriptions .............................................................................. 264
24 Task Failure column descriptions.............................................................................. 267
25 Job Details column descriptions................................................................................267
26 Unprotected Clients column descriptions................................................................. 268
27 Backup appliance detail descriptions........................................................................ 268
28 Email configuration field descriptions........................................................................ 271
29 EMC Backup and Recovery alarms .......................................................................... 290
30 Scalability Factors.................................................................................................... 303
31 Maximum concurrent sessions per VMware Backup Appliance................................. 304
32 Concurrency/parallelism recommendations .............................................................305
33 Application information values ................................................................................. 330
34 VADP recovery privileges ........................................................................................ 332

NetWorker 18.1 VMware Integration Guide 13

TABLES

14 NetWorker 18.1 VMware Integration Guide

Preface

As part of an effort to improve product lines, periodic revisions of software and

hardware are released. Therefore, all versions of the software or hardware currently in
use might not support some functions that are described in this document. The
product release notes provide the most up-to-date information on product features.
If a product does not function correctly or does not function as described in this
document, contact a technical support professional.

Note

This document was accurate at publication time. To ensure that you are using the
latest version of this document, go to the Support website at https://
support.emc.com.

Purpose
This document describes how to configure the NetWorker software to protect a
VMware environment.
Audience
This document is part of the NetWorker documentation set and is intended for use by
system administrators during the configuration of the NetWorker software.
Revision history
The following table presents the revision history of this document.

Table 1 Revision history

Revision Date Description

07 February 28, 2019 Added troubleshooting item "Increase the vCenter
query timeout before starting a VMware backup
action."
Updates to file-level restore limitations for user
requirements for FLR Agent installation on Linux, and
the local Linux account requirement for mounting a
virtual machine.
Updates to "NetWorker VMware Protection Solution
best practices with the vProxy appliance" for
recommendation to enable the vCenter server's
Datastore Browser feature.

06 February 5, 2019 Updates to vProxy incoming and outgoing port

requirements.

05 January 25, 2019 Updates to Prerequisites section of the appendix

"NetWorker VMware Protection in VMware Cloud on
Amazon Web Services."

04 January 7, 2019 Updates to "NetWorker VMware Protection Solution

best practices with the vProxy appliance" for
recommendations when installing third party tools/

NetWorker 18.1 VMware Integration Guide 15

Preface

Table 1 Revision history (continued)

Revision Date Description

applications in the virtual appliance, and the vCenter
server's Datastore Browser feature.
Updates to the section "Domain user setup required for
file-level recovery."

03 August 3, 2018 Added section "Renaming a NetWorker 9.1 and later

server with legacy VMware Backup appliance" for
upgrades from a NetWorker 8.2.x release to 9.1 and
later.

02 July 18, 2018 Removed troubleshooting item "Backups failing for

virtual machines containing both hotadd disks and disks
that do not support hotadd mode such as IDE and
SATA."

01 July 7, 2018 First release of this document for NetWorker 18.1.

Related documentation
The NetWorker documentation set includes the following publications, available on the
Support website:
l NetWorker Online Software Compatibility Matrix
Provides compatibility information, including specific software and hardware
configurations that NetWorker supports. To access the matrix, go to http://
compatibilityguide.emc.com:8080/CompGuideApp/.
l NetWorker Administration Guide
Describes how to configure and maintain the NetWorker software.
l NetWorker Network Data Management Protocol (NDMP) User Guide
Describes how to use the NetWorker software to provide data protection for
NDMP filers.
l NetWorker Cluster Integration Guide
Contains information related to configuring NetWorker software on cluster servers
and clients.
l NetWorker Installation Guide
Provides information on how to install, uninstall, and update the NetWorker
software for clients, storage nodes, and servers on all supported operating
systems.
l NetWorker Updating from a Previous Release Guide
Describes how to update the NetWorker software from a previously installed
release.
l NetWorker Release Notes
Contains information on new features and changes, fixed problems, known
limitations, environment and system requirements for the latest NetWorker
software release.
l NetWorker Command Reference Guide
Provides reference information for NetWorker commands and options.
l NetWorker Data Domain Boost Integration Guide
Provides planning and configuration information on the use of Data Domain
devices for data deduplication backup and storage in a NetWorker environment.

16 NetWorker 18.1 VMware Integration Guide

 Preface

l NetWorker Performance Optimization Planning Guide

Contains basic performance tuning information for NetWorker.
l NetWorker Server Disaster Recovery and Availability Best Practices Guide
Describes how to design, plan for, and perform a step-by-step NetWorker disaster
recovery.
l NetWorker Snapshot Management Integration Guide
Describes the ability to catalog and manage snapshot copies of production data
that are created by using mirror technologies on storage arrays.
l NetWorkerSnapshot Management for NAS Devices Integration Guide
Describes how to catalog and manage snapshot copies of production data that are
created by using replication technologies on NAS devices.
l NetWorker Security Configuration Guide
Provides an overview of security configuration settings available in NetWorker,
secure deployment, and physical security controls needed to ensure the secure
operation of the product.
l NetWorker VMware Integration Guide
Provides planning and configuration information on the use of VMware in a
NetWorker environment.
l NetWorker Error Message Guide
Provides information on common NetWorker error messages.
l NetWorker Licensing Guide
Provides information about licensing NetWorker products and features.
l NetWorker REST API Getting Started Guide
Describes how to configure and use the NetWorker REST API to create
programmatic interfaces to the NetWorker server.
l NetWorker REST API Reference Guide
Provides the NetWorker REST API specification used to create programmatic
interfaces to the NetWorker server.
l NetWorker 18.1 with CloudBoost 18.1 Integration Guide
Describes the integration of NetWorker with CloudBoost.
l NetWorker 18.1 with CloudBoost 18.1 Security Configuration Guide
Provides an overview of security configuration settings available in NetWorker and
Cloud Boost, secure deployment, and physical security controls needed to ensure
the secure operation of the product.
l NetWorker Management Console Online Help
Describes the day-to-day administration tasks performed in the NetWorker
Management Console and the NetWorker Administration window. To view the
online help, click Help in the main menu.
l NetWorker User Online Help
Describes how to use the NetWorker User program, which is the Windows client
interface, to connect to a NetWorker server to back up, recover, archive, and
retrieve files over a network.
Special notice conventions that are used in this document
The following conventions are used for special notices:

NOTICE

Identifies content that warns of potential business or data loss.

NetWorker 18.1 VMware Integration Guide 17

Preface

Note

Contains information that is incidental, but not essential, to the topic.

Typographical conventions
The following type style conventions are used in this document:

Table 2 Style conventions

Bold Used for interface elements that a user specifically selects or clicks,
for example, names of buttons, fields, tab names, and menu paths.
Also used for the name of a dialog box, page, pane, screen area with
title, table label, and window.

Italic Used for full titles of publications that are referenced in text.
Monospace Used for:
l System code
l System output, such as an error message or script
l Pathnames, file names, file name extensions, prompts, and
syntax
l Commands and options

Monospace italic Used for variables.

Monospace bold Used for user input.

[] Square brackets enclose optional values.

| Vertical line indicates alternate selections. The vertical line means or

for the alternate selections.

{} Braces enclose content that the user must specify, such as x, y, or z.

... Ellipses indicate non-essential information that is omitted from the

example.

You can use the following resources to find more information about this product,
obtain support, and provide feedback.
Where to find product documentation
l https://support.emc.com
l https://community.emc.com
Where to get support
The Support website at https://support.emc.com provides access to licensing
information, product documentation, advisories, and downloads, as well as how-to and
troubleshooting information. This information may enable you to resolve a product
issue before you contact Support.
To access a product specific Support page:
1. Go to https://support.emc.com/products.
2. In the Find a Product by Name box, type a product name, and then select the
product from the list that appears.
3. Click .
4. (Optional) To add the product to My Saved Products, in the product specific
page, click Add to My Saved Products.

18 NetWorker 18.1 VMware Integration Guide

 Preface

Knowledgebase
The Knowledgebase contains applicable solutions that you can search for by solution
number, for example, 123456, or by keyword.
To search the Knowledgebase:
1. Go to https://support.emc.com.
2. Click Advanced Search.
The screen refreshes and filter options appear.
3. In the Search Support or Find Service Request by Number box, type a solution
number or keywords.
4. (Optional) To limit the search to specific products, type a product name in the
Scope by product box, and then select the product from the list that appears.
5. In the Scope by resource list box, select Knowledgebase.
The Knowledgebase Advanced Search panel appears.
6. (Optional) Specify other filters or advanced options.
7. Click .
Live chat
To participate in a live interactive chat with a support agent:
1. Go to https://support.emc.com.
2. Click Chat with Support.
Service requests
To obtain in-depth help from Licensing, submit a service request. To submit a service
request:
1. Go to https://support.emc.com.
2. Click Create a Service Request.

Note

To create a service request, you must have a valid support agreement. Contact a sales
representative for details about obtaining a valid support agreement or with questions
about an account. If you know the service request number, then directly enter the
service request number in the Service Request field to get the valid details.

To review an open service request:

1. Go to https://support.emc.com.
2. Click Manage service requests.
Online communities
Go to the Community Network at https://community.emc.com for peer contacts,
conversations, and content on product support and solutions. Interactively engage
online with customers, partners, and certified professionals for all products.
How to provide feedback
Feedback helps to improve the accuracy, organization, and overall quality of
publications. You can send feedback to [email protected].

NetWorker 18.1 VMware Integration Guide 19

Preface

20 NetWorker 18.1 VMware Integration Guide

CHAPTER 1
Introduction to NetWorker VMware Protection
with the vProxy appliance

This chapter contains the following topics:

l Introduction to NetWorker VMware Protection with vProxy appliance.............. 22

l Components in the NetWorker VMware Protection Solution with vProxy
appliance............................................................................................................22
l System requirements......................................................................................... 23
l Port requirements.............................................................................................. 25
l vProxy limitations and unsupported features......................................................27
l Compatibility information................................................................................... 30
l Recommendations and considerations............................................................... 30
l Accessing Knowledge Base Articles................................................................... 36

Introduction to NetWorker VMware Protection with the vProxy appliance 21

Introduction to NetWorker VMware Protection with the vProxy appliance

Introduction to NetWorker VMware Protection with vProxy

appliance
NetWorker 18.1 releases provide you with the ability to perform virtual machine
protection and recovery by using the NetWorker VMware Protection solution with the
vProxy appliance, also known as NVP.
NVP features the following:
l Uses standalone data-mover proxy appliances, or vProxy appliances, to backup
and restore virtual machines that run in a virtualized infrastructure, with the ability
to offload the data mover from NetWorker and run the backup as a virtual
workload.
l NetWorker directly manages the vProxy appliances without the use of an external
node for proxy management and load balancing.
l Stores the virtual machine backups as raw virtual machine disk files (VMDKs) on
the Data Domain device, which reduces overhead. NetWorker does not convert
the backup to any backup streaming formats.
l Provides the ability to clone virtual machine backups. When you use streaming
devices such as tape, NetWorker converts the save set directories format (SSDF)
to Common Data Storage Format (CDSF) during a clone operation, and converts
back to SSDF on Data Domain for recovery from streaming devices.
l Provides user interfaces to perform image-level recovery or file-level recovery.

Note

If upgrading to NetWorker 18.1, you can continue to use the legacy NetWorker
VMware Protection Solution with the VMware Backup appliance (VBA) to run existing
VMware Backup appliance protection policies. However, you will not be able to create
any new policies using the VMware Backup Appliance, and you cannot recover
backups performed with the VMware Backup appliance by using the vProxy appliance.

Components in the NetWorker VMware Protection Solution

with vProxy appliance
The following section provides a high-level overview of the components in the
NetWorker VMware Protection Solution with the vProxy appliance.
Figure 1 Components in a NetWorker VMware Protection Solution

22 NetWorker 18.1 VMware Integration Guide

 Introduction to NetWorker VMware Protection with the vProxy appliance

The solution contains the following components:

l vProxy appliances—Provide the data movement services between the VMware
host and the target protection storage, for example Data Domain.
l NetWorker server—Provides the ability to manage vProxy appliances, configure
data protection policies for backup and clone operations. Integrates with file-level
restore to provide centralized management in a virtual environment.
l NMC server—Provides the ability to start, stop, and monitor data protection
policies and perform recovery operations.
l Dell EMC Data Protection Restore client—Provides the ability to perform file-level
restore by using a web interface.
l DDR1 and DDR2—Data Domain appliances that receive and clone backup data in
SSDF format.
l Tape device—Media that receives backup data in CDSF format.

System requirements
The following table lists the required components for NetWorker VMware Protection
with the vProxy appliance.
When you install or upgrade NetWorker and deploy the vProxy appliance, ensure that
the NetWorker server and storage node are at the same version, and that you use the
latest version of the vProxy appliance.

System requirements 23
Introduction to NetWorker VMware Protection with the vProxy appliance

Table 3 NetWorker VMware Protection with vProxy appliance requirements

Component Requirements
NetWorker NetWorker 18.1 server software with NMC.

Note

The NetWorker storage node should be the

same version as the NetWorker server.

vProxy Appliance Version 2.3.0-3 System requirements for the

vProxy include:
l CPU: 4 * 2 GHz (4 virtual sockets, 1 core
for each socket).
l Memory: 8GB.
l Disks: 2 disks (59 GB and 98 GB).
l Internet Protocol: IPv4 only; dual stack
and IPv6 not supported.
l SCSI controller: Maximum 4.
l NIC: One vmxnet3 NIC with one port.

vCenter server l Version 5.5, 5.5 U2, 5.5 U3a, 5.5 U3b, 5.5
U3d, 6.0, 6.0 U1b, 6.0 U2, 6.5, 6.50b.

Note

Version 6.5 and later is required to

perform Microsoft SQL Server
application-consistent protection.

l Linux or Windows platform, or VC

appliance.

ESX/ESXi server l Version 5.5, 5.5 U2, 5.5 U3a, 5.5 Ub, 6.0
U1, 6.0 U1b, 6.0 U2, 6.5, 6.50b.

Note

Version 6.5 and later is required to

perform Microsoft SQL Server
application-consistent protection.

l Automatically enables Changed Block

Tracking (CBT) on each virtual machine.

VMware Tools Version 10 or later.

Note

Version 10.1 and later is required to perform

Microsoft SQL Server application-consistent
protection.

24 NetWorker 18.1 VMware Integration Guide

 Introduction to NetWorker VMware Protection with the vProxy appliance

Table 3 NetWorker VMware Protection with vProxy appliance requirements (continued)

Component Requirements
Data Domain l A minimum of one configured DD Boost
device is required. Additionally, you must
specify one pool that contains the DD
Boost device.
l Data Domain system OS at DDOS version
5.7, 6.0.0.30, 6.0.1-10, or 6.1. If using
DDOS 5.7.x, 5.7.1 is recommended.

Note

The NetWorker compatibility matrix at

http://compatibilityguide.emc.com:
8080/CompGuideApp/ provides detailed
information on NetWorker and DD Boost
version compatibility.

l A Data Domain user account with

administrator privileges, which you will
use to manage file-level restore and
instant access restore.

Port requirements
The NetWorker VMware Protection solution requires the ports outlined in the
following tables.

Table 4 Incoming port requirements

From To Port Purpose

NetWorker server vProxy appliance 9090 NetWorker VMware
Protection web
service calls to initiate
and monitor backups,
image recoveries, and
granular recoveries.

NetWorker server vCenter server 443 VMware View in NMC

vCenter server NetWorker server 9090 vSphere Client's VM

Backup and Recovery
plug-in

Dell EMC Data NetWorker server 9090 File-level recovery in

Protection Restore the Dell EMC Data
Client interface Protection Restore
Client

ESXi servers Data Domain 111, 2049, 2052 File-level recovery

and instant recovery

Port requirements 25
Introduction to NetWorker VMware Protection with the vProxy appliance

Table 4 Incoming port requirements (continued)

From To Port Purpose

Virtual machines Data Domain 111, 2049 SQL application-
The NetWorker Data consistent backup
Domain Boost
Integration Guide also
provides information
about firewall ports
required for DD
Boost.

Table 5 Outgoing port requirements

From To Port Purpose

vProxy Appliance DNS 53 Name resolution

vProxy Appliance Data Domain 22, 111, 131, 161, 2049, Data Domain
2052 management

vProxy Appliance ESXi server 443, 902 Backup and recovery

operations

vProxy Appliance vCenter server 443 Backup and recovery

operations

Figure 2 Port requirements for NetWorker VMware Protection with the vProxy appliance

26 NetWorker 18.1 VMware Integration Guide

 Introduction to NetWorker VMware Protection with the vProxy appliance

vProxy limitations and unsupported features

Before you deploy the NetWorker VMware Protection Solution with the vProxy
appliance, review the following limitations and unsupported features.

Note

Review the VMware limitations:

l vSphere 5.5—https://www.vmware.com/pdf/vsphere5/r55/vsphere-55-
configuration-maximums.pdf
l vSphere 6.0—https://www.vmware.com/pdf/vsphere6/r60/vsphere-60-
configuration-maximums.pdf
l vSphere 6.5—https://www.vmware.com/pdf/vsphere6/r65/vsphere-65-
configuration-maximums.pdf

Limitations to SQL Server application consistent data protection

Review the SQL Server application-consistent protection support limitations in
the section Enable the Microsoft VM App Agent for SQL Server application-
consistent protection.

Network configuration settings do not get restored with virtual machine after
recovery of a vApp backup
Network configuration settings are not backed up with the virtual machine as part
of a vApp backup in NetWorker. As a result, when you restore a vApp backup, you
must manually reconfigure the network settings.

vProxy appliance configured with dual stack or IPv6 only is not supported
The vProxy appliance does not support dual stack (IPv4 and IPv6) or IPv6 only
addressing. If you want to run backups and restores using the vProxy appliance,
use IPv4 addressing for the vProxy and disable IPv6.

vCenter version not updated in RAP database after upgrade

When you upgrade vCenter, the vCenter version does not get updated
immediately in the RAP database since NetWorker does not periodically query
vCenter. After the upgrade, refresh VMware View in NMC's Administration
window for the vCenter version to update.

Concurrent vProxy workflows on the same virtual machine is not supported when not
using a vCenter server
NetWorker does not support running multiple vProxy workflows concurrently
(backup, image-level recovery, or file-level restore operations) on the same
virtual machine when not using a vCenter server in your environment.

Data Domain system requires REPLICATION license when clone of VMware backup
performed to same system as the backup
When cloning VMware backups using NetWorker VMware Protection with the
vProxy appliance, if the clone is performed to the same Data Domain system as
the backup, a REPLICATION license is required on the Data Domain system.

vProxy cannot perform recoveries from policies run with VMware Backup appliance
After upgrading to a NetWorker release with the vProxy appliance, any policies
run with the VMware Backup appliance cannot be recovered with the vProxy

vProxy limitations and unsupported features 27

Introduction to NetWorker VMware Protection with the vProxy appliance

appliance. If you want to recover these backups you must continue to use the
VMware Backup appliance.

No new policies can be created with VMware Backup appliance

After upgrading to a NetWorker release with the vProxy appliance, new policies
can only be created with the vProxy appliance. You can continue to run and edit
existing VMware Backup Appliance policies, but once you delete a VMware
Backup appliance policy, it is no longer available. A message appears each time
you run a VMware Backup Appliance policy recommending that you use the
vProxy appliance.

Virtual machine alert "VM MAC conflict" may appear after successful recovery of
virtual machine
After performing a successful recovery of a virtual machine through vCenter
version 6, an alert may appear indicating a "VM MAC conflict" for the recovered
virtual machine, even though the new virtual machine will have a different and
unique MAC address. You must manually acknowledge the alert or clear the alert
after resolving the MAC address conflict. Note that this alert can be triggered
even when the MAC address conflict is resolved.
The VMware release notes at http://pubs.vmware.com/Release_Notes/en/
vsphere/60/vsphere-vcenter-server-60u2-release-notes.html provide more
information.

Emergency recovery cannot be performed until vProxy registration event successful

with NetWorker
When deploying a new vProxy that is not yet registered with NetWorker, wait for
the registration event to complete successfully with NetWorker before
performing an emergency recovery in the NMC Recovery wizard. The event will
appear in the logs and in NMC.

Datastore names cannot contain special characters

Using special characters in datastore names can cause problems with the vProxy,
such as failed backups and restores. Special characters include the following: % &
* $ # @ ! \ / : * ? " < > | ;, and so on.

Backups fail for resource pools recreated with the same name as deleted pool
When you delete a resource pool in vCenter and then recreate a resource pool
with the same name, backups fail. Re-configure the protection group with the
newly created resource pool.

Data Domain Boost over fibre channel not supported

The NetWorker VMware Protection Solution does not support Data Domain Boost
over fibre channel (DFC).

Data Domain SMT not supported

The NetWorker VMware Protection Solution does not support Data Domain SMT.
You can create different DDBoost users to segregate access to specific DD Boost
devices. However DD Admin credentials are required for performing instant
access and file-level restore workflows.

Only hotadd and NBD transport modes supported

The NetWorker VMware Protection Solution supports only the hotadd and NBD
transport modes. The hotadd mode is the default transport mode. If you want to
use both modes, the maximum sessions value for each must be set to the same
non-zero value. For example, set hotadd = 13 and nbd = 13. If you only want to
use one transport mode, ensure that you set the maximum sessions value for the

28 NetWorker 18.1 VMware Integration Guide

 Introduction to NetWorker VMware Protection with the vProxy appliance

other transport mode to 0. For example, if you want to use hotadd mode only, set
hotadd = 25 and nbd = 0.

Note

If upgrading to NetWorker 18.1 from a previous release where the hotadd and nbd
transport modes were configured with different non-zero values for maximum
sessions, ensure that you change these settings to the same non-zero value.
Setting different non-zero values for both transport modes is not supported in
NetWorker 18.1.

Specify NBD for datastores if proxies should use NBD mode only
For proxies that only use NBD transport mode (proxies where you specify a value
greater than 0 for the NBD maximum sessions limit), you must also specify the
datastores for which you want the proxy to perform only NBD backups to ensure
that any backups of virtual machines running on these datastores are always
performed using NBD mode. This also ensures that the same NBD-only proxies
are never used for backups of virtual machines residing on any other datastores.

Backup of individual folders within a Virtual Machine is not supported

The NetWorker VMware Protection Solution only supports image-level backup
and disk-level backup. You cannot perform backups of individual folders within
the Virtual Machine.

VMware View in the NetWorker Administration map view does not display when
configuration for Virtual Machines within the vCenter is incomplete
When you use VMware View, the map view does not appear when the
configuration for one or more Virtual Machines in the vCenter is incomplete. To
avoid this issue, remove the incomplete Virtual Machine configurations from
vCenter.

I/O contention when all Virtual Machines on a single data store

I/O contention may occur during snapshot creation and backup read operations
when all Virtual Machines reside on a single datastore.

No automatic migration tool to move from previous solution to NetWorker VMware

Protection with the vProxy appliance
An automatic migration tool to move from the previous virtual machine backup
solution to the NetWorker VMware Protection with vProxy appliance solution
does not exist.

VMware snapshot for backup is not supported for independent disks

When using independent disks you cannot perform VMware snapshot for backup.

Cannot select a vProxy or the cloned vProxy when you create a VMware group
When you create a new protection group, you cannot select vProxy or clones of
the vProxy from the hosts list. To use the clone vProxy as a normal virtual
machine, clear the annotation string This is EMC Backup and Recovery
vProxy Appliance in the Notes section of the cloned vProxy virtual machine.

Restricted data zones not supported

NetWorker VMware Protection with the vProxy appliance does not currently
support the protection of virtual machines within a Restricted Data Zone. When
you create a VMware policy in NMC, ensure that you leave the Restricted Data
Zone field blank.

vProxy limitations and unsupported features 29

Introduction to NetWorker VMware Protection with the vProxy appliance

Compatibility information
The NetWorker Online Compatibility matrix provides software compatibility
information for the NetWorker release, which includes NetWorker VMware Protection
with the vProxy appliance.
The guide is available at http://compatibilityguide.emc.com:8080/CompGuideApp/.

Note

For compatibility information related to the Microsoft VM App Agent for SQL Server
application-consistent protection, refer to the NMM support matrix.

Recommendations and considerations

This section provides information about performance and scalability, best practices,
and a configuration checklist.

Performance and scalability

Performance and scalability of the NetWorker VMware Protection Solution depends
on several factors, including the number of vCenter servers and proxies and the
number of concurrent virtual machine backups. The following table provides
information on these scalability factors and maximum recommendations, in addition to
concurrency recommendations for sessions created from backups of the vProxy
appliance. The count of sessions is driven by the number of proxies, clone jobs, and
other backups running through this server. Each vProxy Appliance can run up to 25
sessions.

Table 6 Performance and scalability factors

Component Maximum Recommended Notes

limit count
Number of concurrent 25 13 It is recommended to use 13 hotadd sessions to
hotadd backups per proxy achieve optimal performance.

Number of concurrent NBD 25 It is recommended to use hotadd transport mode for

backups per proxy optimal performance. When using VMware NBD mode,
use of 10G network is recommended.

Number of concurrent NBD 50 (10G VMware uses Network File Copy (NFC) protocol to
backups per vCenter server network) read VMDK using NBD transport mode. You need one
VMware NFC connection for each VMDK file being
backed up. The VMware Documentation provides more
information on vCenter NFC session connection limits.

Virtual machines concurrent 100 100 Can be achieved with a combination of the number of
backups per vCenter server proxies multiplied by the number of configured hotadd
sessions per vProxy.

Number of proxies per 8 8 proxies with 12-13 hotadd sessions on each proxy can
vCenter protect 100 virtual machines concurrently. If more than
8 proxies are required per vCenter, configure the
hotadd limits on the proxies to ensure that no more

30 NetWorker 18.1 VMware Integration Guide

 Introduction to NetWorker VMware Protection with the vProxy appliance

Table 6 Performance and scalability factors (continued)

Component Maximum Recommended Notes

limit count
than 100 proxy streams run concurrently against any
given vCenter.

Number of workflows per 64 8 Ensure that you do not to exceed 2000 virtual
VMware policy machines per VMware policy.

Number of virtual machines 2000 Ensure that you do not to exceed 2000 virtual
per workflow machines per VMware policy.
Note that the maximum of 2000 virtual machines per
workflow is only applicable to the first FULL backup to
Data Domain, and does not apply to CBT-based
incremental backups of the virtual machines.
However, ensure that you do not exceed 100
connections per vCenter at any time during the backup
window.

Number of vCenter servers 5 3 Per policy you can use 5 vCenter servers in the
per policy respective workflows and trigger concurrent backups.

Number of concurrent 50 It is recommended to use hotadd transport mode for

recoveries recoveries. For large concurrent restores, it is highly
recommended that multiple target datastores are used
for optimal performance

Number of files/directories 20000 or less File-level recovery is recommended for quickly

per file level recovery (User recovering a small set of files. Image-level or VMDK-
and Admin mode) level recoveries are optimized and recommended for
recovering a large set of files/folders.

Number of parallel instant 32 You can perform up to 32 parallel instant recovery

access sessions sessions using nsrvproxy_recover, provided that
you satisfy the following prerequisites:
l For the backups being restored, you must select
Performance backup optimization mode during
VMware type group creation in NMC.
l Data Domain OS version 6.0.0.30 is supported.
l Data Domain platforms supported include DD6300
(EOS-T2), DD6800 (EOS-T3), DD9300 (EOS-T4),
and DD9800.
l The ESXi host requires the following default values
to be updated to the maximum supported:
Under NFS, update NFS.MaxVolumes.

Under Net, update Net.TcpipHeapSize.

Under Net, update Net.TcpipHeapMax.

The VMware knowledgebase article at https://
kb.vmware.com/kb/2239 provides more information.
Additionally, refer to the VMware Documentation for
concurrent virtual machine migration limits.

Performance and scalability 31

Introduction to NetWorker VMware Protection with the vProxy appliance

Table 6 Performance and scalability factors (continued)

Component Maximum Recommended Notes

limit count
Total number of virtual 2000 1000 You can run multiple vProxy policies concurrently as
machines in a single long as the total number of concurrent backup streams
NetWorker policy does not exceed the vCenter limits indicated in this
table.
In the case of a single vCenter, stagger the schedules
for policies to ensure that all the backups for a policy
complete before the backups of the next policy begin.

Backup Optimization modes During creation of a VMware type group in NMC, you
can select a backup optimization mode of either
Capacity or Performance. Performance mode
results in additional space use on the Data Domain
device (around 20%) but significantly improves
random I/O performance for instant access restores.

NetWorker VMware Protection Solution best practices with the vProxy

appliance
Observe the following best practices when using the NetWorker VMware Protection
Solution with the vProxy appliance.
Software recommendations
Review the following software recommendations:
l Ensure that the NetWorker server and storage node are at the same version, and
that all the vProxy appliances you deploy are compatible with this version.
l Install VMware Tools on each virtual machine by using the vSphere Web Client.
VMware Tools adds additional backup and recovery capabilities that quiesce
certain processes on the guest operating system prior to backup.
l Installation of third-party tools or applications in the virtual appliance for the
purposes of monitoring the appliance status and protecting the appliance from
computer viruses can have a negative impact on system performance. Therefore,
it is recommended that you do not install any additional tools or applications in the
appliance.
Configuration recommendations
l Ensure that the vCenter server's Datastore Browser feature is enabled, which
allows you to browse all datastores associated with the vSphere environment.
NetWorker VMware Protection requires this feature to download configuration
files for a virtual machine during backup and recovery operations.
This feature is enabled by default, but you can verify the feature status by opening
the vpxd.cfg file within your vCenter configuration, and ensuring that the entry
for enableHttpDatastoreAccess is either set to true or is not contained in the
file. Information on how to locate the vpxd.cfg file within your vCenter
configuration is provided in the VMware documentation.
l vProxy remote site configurations with a storage node communication latency
greater than 50 ms require a storage node in the remote site.
l Avoid deploying VMs with IDE virtual disks; using IDE virtual disks degrades
backup performance. Use SCSI virtual disks instead whenever possible.

32 NetWorker 18.1 VMware Integration Guide

 Introduction to NetWorker VMware Protection with the vProxy appliance

Note

You cannot use hotadd mode with IDE Virtual disks and therefore backup of these
disks will be performed using NBD mode.
l For best practices related to SQL Server application-consistent protection, review
the software and security requirements in the section Enable the Microsoft VM
App Agent for SQL Server application-consistent protection.
l During policy configuration, assign virtual machines to a protection group based on
logical grouping to allow for better scheduling of backups that will help you avoid
resource contention and create more organized logs for review.
l When you plan the backups, ensure that NetWorker VMware Protection supports
the disk types that you use in the environment. Currently, NetWorker VMware
Protection does not support the following disk types:
n Independent (persistent and non-persistent)
n RDM Independent - Virtual Compatibility Mode
n RDM Physical Compatibility Mode
l The vProxy Appliance leverages Changed Block Tracking (CBT) by default. If CBT
is disabled on the virtual machine, then it will enable CBT automatically. If you add
a disk to the virtual machine after the first full backup, for the next policy run a full
backup will be performed automatically for the newly added disk, and an
incremental backup will be performed for the existing disk. For information on
disabling CBT, refer to the section Enabling or disabling Changed Block Tracking.
l When backing up thin-provisioned Virtual Machines or disks for Virtual Machines
on NFS datastores, an NFS datastore recovery does not preserve thin
provisioning. VMware knowledge base article 2137818 at http://
kb.vmware.com/kb/2137818 provides more information.
l It is recommended that you set an appropriate NetWorker server/storage
parallelism value, according to the available resources, to reduce queuing. For
example, 5 vProxy appliances with backup and clone operations will require more
than 125 parallel sessions. Therefore, setting the parallelism for the NetWorker
server to 128 or higher (while also setting the server with 32+ GB memory and 8+
CPUs) will suit such an environment. The NetWorker Performance Optimization
Planning Guide provides more details.
If you require a larger number of parallel image backups, also consider setting the
maximum number of vCenter SOAP sessions to larger value. Note that this
requires careful planning and additional resources on the vCenter Server You can
configure this by modifying the following line in the vCenter vpxd.cfg file:
<vmacore><soap><maxSessionCount> N </maxSessionCount></soap></
vmacore>
This applies specifically to SDK sessions as opposed to VI client sessions:
l Each Virtual Machine backup to a Data Domain system consumes more than one
session on the Data Domain device. The default device configuration is target
sessions=20 and max session=60, however it is recommended that you
configure additional devices for more than 10 parallel backups.
l Virtual Machines with extremely high IO may face hangs during consolidation due
to the ESXi forced operation called synchronous consolidate. Plan your backups of
such Virtual Machines according to the amount of workload on the Virtual
Machine.

NetWorker VMware Protection Solution best practices with the vProxy appliance 33
Introduction to NetWorker VMware Protection with the vProxy appliance

l When you work with the vCenter database either directly or by using scripts, do
not change the name attribute for the vmfolder object. VMware knowledge base
article at https://support.emc.com/kb/190755 provides more information.
l Resource contention can occur at various points during the backup cycle. When
NetWorker runs larger policies, issues due to contention of resources can occur,
which impact all running operations. Adjust your resources and times for other
larger policies to avoid overlaps, and avoid resource contention.
For example, you configure one pool named Bronze, with one device. If you set up
a policy where every day at 10 pm two policies called 'Bronze1' and 'Bronze2' with
400 virtual machines each start writing to the device in the 'Bronze' pool, then the
long wait for device availability may cause unexpected delays or timeouts. To fix
this, set the policy start times 4 hours apart and add more devices, to allow for
stable backups.
Transport mode recommendations
Review the following recommendations for transport mode settings:
l Use hotadd transport mode for faster backups and restores and less exposure to
network routing, firewall, and SSL certificate issues. The vProxy appliance
currently supports a maximum of 25 concurrent hotadd sessions. To support
hotadd mode, deploy the vProxy on an ESXi host that has a path to the storage
that holds the target virtual disk(s) for backup.

Note

Hotadd mode requires VMware hardware version 7 or later. Ensure that all virtual
machines that you back up with Hotadd mode are using Virtual Machine hardware
version 7 or later.

For sites that contain a large number of virtual machines that do not support
hotadd requirements, NBD transport mode will be used. This can cause congestion
on the ESXi host management network. Plan your backup network carefully for
large scale NBD installs. You may consider configuring one of the following
options:
n Set up Management network redundancy.
n Set up backup network to ESXi for NBD.
n Set up storage heartbeats. http://www.vmware.com/files/pdf/techpaper/
vmw-vsphere-high-availability.pdf provides more information.
l If you have vFlash-enabled disks and are using hotadd transport mode, ensure that
you configure the vFlash resource for the vProxy host with sufficient resources
(greater than or equal to the virtual machine resources), or migrate the vProxy to
a host with vFlash already configured. Otherwise, backup of any vFlash-enabled
disks will fail with the error "VDDK Error: 13: You do not have access rights to this
file," and the error "The available virtual flash resource '0' MB ('0' bytes) is not
sufficient for the requested operation" on the vCenter server.
l If you only want to use one transport mode, ensure that you set the maximum
sessions value for the other transport mode to 0. For example, if you want to use
hotadd mode only set hotadd = 25 and nbd = 0. If you want to use NBD mode only,
set hotadd = 0 and nbd = 10.
l In order for backup and recovery operations to use Hotadd mode on a VMware
Virtual Volume (VVol) datastore, the vProxy should reside on the same VVol as the
virtual machine.

34 NetWorker 18.1 VMware Integration Guide

 Introduction to NetWorker VMware Protection with the vProxy appliance

Configuration checklist
The following configuration checklist provides best practices and troubleshooting tips
that might help resolve some common issues.

Basic configuration
l Synchronize system time between vCenter, ESX/ESXi/vSphere, and the vProxy
appliance
l Assign IPs carefully — do not reuse any IP address
l Use FQDNs (Fully Qualified Domain Names) everywhere
l For any network related issue, confirm that forward and reverse DNS lookups
work for each host in the datazone.

Data Domain system configuration

l Upgrade all Data Domain systems to use DDOS version 5.7, 6.0.0.30, 6.0.1-10, or
6.1. The Data domain Retention Lock feature is also supported for vProxy backup
and clone actions but requires DDOS 6.1.
l Ensure that the Data Domain system does not reach the MTree limit and max-
streams limit.
l Ensure that only devices from the same Data Domain system host appear in Data
Domain system pool when used in any Action.
l Check the NFS settings. By default, only NFS v3 is enabled from the ESXi host. If
using NFS v4, you might be required to disable and use NFS v3 instead in order to
avoid issues with file-level restore operations.
l For virtual machines within in application-consistent data protection policy,
network zoning must be configured to enable network connectivity between the
virtual machines and the Data Domain system.

NetWorker configuration
l Ensure that the relevant devices are mounted.
l Ensure that vProxy IP addresses are populated in DNS, and that the NetWorker
server has name resolution for the vProxy host names.
l Wait until you successfully configure a policy before you run the policy.
l A message appears after successful vProxy registration in NMC.

Virtual machine configuration

l Ensure that the virtual machine network is zoned for access to Data Domain.
l Ensure that the virtual machine has name resolution for the Data Domain system,
if applicable.
l Ensure that the virtual machine firewall has port rules for Data Domain.
l Ensure that Microsoft SQL Server instances are enabled for data protection using
a SYSTEM account, as described in the software and security requirements
section of the topic Enable the Microsoft VM App Agent for SQL Server
application-consistent protection.

Configuration checklist 35
Introduction to NetWorker VMware Protection with the vProxy appliance

Accessing Knowledge Base Articles

Additional troubleshooting information is available through the Featured VMware
Documentation Sets website at https://www.vmware.com/support/pubs/. Select
Support > Search Knowledge Base.

36 NetWorker 18.1 VMware Integration Guide

CHAPTER 2
Deploy the vProxy appliance and configure the
NetWorker datazone

This chapter contains the following topics:

l Deploying the vProxy appliance......................................................................... 38

l VMware vCenter server management.................................................................41
l Configuring and registering the vProxy appliance.............................................. 44
l Installing the vCenter plug-in............................................................................. 47
l Enable the Microsoft VM App Agent for SQL Server application-consistent
protection...........................................................................................................51
l Additional vProxy backup configuration options.................................................56
l Creating a dedicated vCenter user account and VM Backup and Recovery role
...........................................................................................................................59
l Adding a NIC for VMXNET 3 on the vProxy appliance....................................... 65
l Dual vNIC setup and configuration requirements............................................... 68
l Verify vNIC connectivity.................................................................................... 69
l Migrating policies from VMware Backup appliance to vProxy appliance.............70
l Updating the Microsoft VM App Agent and FLR Agent software....................... 75
l Updating the vProxy appliance...........................................................................75
l Deleting the vProxy host ................................................................................... 76
l Redeploying a vProxy......................................................................................... 77
l Un-registering and re-registering a vProxy after removal...................................77
l Resetting the admin account password ............................................................. 77

Deploy the vProxy appliance and configure the NetWorker datazone 37

Deploy the vProxy appliance and configure the NetWorker datazone

Deploying the vProxy appliance

You can deploy the vProxy appliance from either of the following:
l The vCenter server.
l The ESXi host.
Registration and configuration of the vProxy appliance must then be completed in the
NMC NetWorker Adminstration window's VMware Proxy Configuration wizard, or
the NetWorker Management Web UI.

Deploy the vProxy OVA on a vCenter server

When deploying the vProxy OVA on a vCenter server, configure the host with a
trusted SSL certificate, and then perform the following steps to deploy the OVA for
the vProxy host from a vCenter server by using the vSphere Web Client.
Before you begin
Install or upgrade to the latest version of the VMware Client Integration Plug-in. This
plug-in is required to run the vSphere Web Client. Download information is provided in
the knowledgebase article at https://kb.vmware.com/selfservice/microsites/
search.do?language=en_US&cmd=displayKC&externalId=2145066.
Procedure
1. Log in to the vSphere Client with an administrator account.
2. In the Main menu, expand vCenter and then expand Hosts.
3. Right-click the ESXi host on which you will deploy the OVA and select Deploy
OVF template.
4. On the Source window, type a URL path to the OVA package or click Browse
and navigate to the OVA package location, and then click Next.
5. On the Review details window, review the product details such as the product
name, version, vendor, publisher, and download size, and then click Next.
6. On the Accept License Agreements window, the EULA appears. Review the
EULA and then click Accept.
7. On the Select name and folder window, specify a name for the virtual
appliance, and optionally the inventory location, for example a datacenter or VM
folder. Click Next.
8. On the Select storage window, select disk format and the destination
datastore on which to store the virtual appliance files and then click Next.
It is recommended that you select Thick Provision Lazy Zeroed to ensure that
amount of storage space allocated to the virtual appliance is available.
9. (Optional) On the Select resource window, select the host, vApp, or resource
pool in which to deploy the OVA, and then click Next.
10. On the Setup networks window, select the Source and Destination networks to
use with the appliance, and then click Next.
11. On the Customize template window, specify the following attributes, and then
click Next.
a. Expand Networking properties, and then perform the following tasks:
l In the Network IP address field, specify the IP address for the vProxy
appliance.

38 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

l In the Default gateway field, specify the IP address of the gateway host.
l In the Network Netmask/Prefix field, specify the netmask for an IPv4
Network IP address. vProxy backups do not support the use of IPv6
Network IP addresses.

b. Expand DNS settings, and then perform the following tasks:

l In the DNS field, specify the IP address of the DNS servers, separated by
commas.
l In the FQDN field, specify the fully qualified domain name of the vProxy
appliance.

c. Expand Timezone settings and in the Timezone setting field, select the
timezone.

Note

To set a timezone outside of the list supported by the vProxy appliance, you
need to change the timezone manually. SSH into the vProxy appliance using
root credentials and run the following command: /usr/bin/timedatectl
set-timezone new-timezone

d. Expand Password settings, and then perform the following tasks:

l In the Root password field, specify a password for the root account or
leave the field blank to use the default password. The default password is
changeme.
l In the Admin password field, specify a password for the admin account
or leave the field blank to use the default password. The default
password is a3dp@m8n.

12. On the Ready to Complete window, review the deployment configuration

details. If you will immediately configure the appliance, select Power on after
deployment, and then click Finish.
The Deploying window appears and provides status information about the
deployment.

Deploy the vProxy OVA on an ESXi host

Perform the following steps to deploy the OVA for the vProxy host from an ESXi host.
Before you begin
Download the vProxy OVA package specific to your platform from the NetWorker
downloads page at https://support.emc.com/downloads/1095_NetWorker.
Procedure
1. Log into the ESXi host with an administrator account.
2. From the File menu, select Deploy OVF Template.
3. On the Source window, type a URL path to the OVA package or click Browse
and navigate to the OVA package location, and then click Next.
4. On the OVF Template Details window, review the product details such as the
product name, version, vendor, publisher, and download size, and then click
Next.

Deploy the vProxy OVA on an ESXi host 39

Deploy the vProxy appliance and configure the NetWorker datazone

5. On the Accept License Agreements window, the EULA appears. Review the
EULA and then click Accept.
6. On the Name and Location window, specify a name for the virtual appliance,
and optionally the inventory location, for example a datacenter or VM folder.
Click Next.
7. If the location you selected in the previous step has more than one available
host, the Host / Cluster window appears. Select the ESXi host or cluster on
which you want to deploy the virtual appliance, and then click Next.
8. On the Resource Pool window, perform one of the following tasks, and then
click Next.
l When you deploy the virtual appliance in a cluster with multiple hosts, select
the specific host in the cluster on which to deploy the virtual appliance.

Note

If DRS is enabled, the target host is automatically selected.

l When you deploy the virtual appliance on a host with a resource pool or
vApp, select the resource pool or vApp on which to deploy virtual appliance.

9. On the Storage window, select the destination datastore on which to store the
virtual appliance files, and then click Next.
10. On the Disk Format window, select the disk format.
EMC recommends that you select Thick Provision Lazy Zeroed to ensure that
amount of storage space allocated to the virtual appliance is available.
11. On the Network Mapping window, select the Source and Destination networks
to use with the appliance, and then click Next.
12. On the Ready to Complete window, review the deployment configuration
details. If you will immediately configure the appliance, select Power on after
deployment, and then click Finish.
The Deploying window appears and provides status information about the
deployment.

Configure the network settings

After you deploy the vProxy appliance on the ESXi host, configure the network
settings from a console window.
Procedure
1. From the vSphere Client application, open a console window on the vProxy
appliance or use ssh to connect to the appliance from a host that has network
access to the vProxy appliance.
2. Log in to the appliance with the root account.
The default password for the root account is changeme.
3. Use the /opt/emc/vproxy/bin/config_network.sh command to
configure the network settings.
For example: /opt/emc/vproxy/bin/config_network.sh fqdn IP address
netmask gateway "dns_server1, dns_server2, ... dns_serverN"
where:
l fqdn is the Fully Qualified Domain Name of the appliance.

40 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

l IP address is the IP address of the appliance.

l netmask is the netmask of the appliance.
l gateway is the name or IP address of the gateway host.
l " dns_server1, dns_server2, ... dns_serverN" is a comma-separated list of IP
addresses or hostnames for the DNS servers, enclosed in quotes.
The config_network.sh man page provides more information about how to
use the config_network.sh command.

Note

After you configure these settings, any subsequent network configuration

changes, including DNS name resolution, require a restart of all vProxy services.

VMware vCenter server management

Add the vCenter server to create the client resource for configuring vProxy backups.
Networker provides two options to add, edit or delete the vCenter server:
l VMware View in NMC's NetWorker Administration window.
l The NetWorker Management Web UI.
When you add a vCenter server, the NetWorker server also creates a client resource
for the vCenter server. You will use this client resource to configure VMware backups.

Add the vCenter server using NMC's VMware View

You can also use VMware View in NMC's NetWorker Administration window to add
a vCenter server. To add the vCenter server, perform the following.
Procedure
1. In the NetWorker Administration window, click Protection.
2. In the left navigation pane, expand the NetWorker server, right-click VMware
View, and then select Add vCenter.
The Add vCenter window appears.
3. In the Host Name field, specify the FQDN of the vCenter server.
4. In the User Name field, specify a vCenter user account that has permissions to
perform backups.
5. In the Password field, specify the password for the account for the vCenter
server.
6. If the vCenter server is deployed in the Cloud, select the Deployed in Cloud
checkbox, and then click OK.

Note

When you select Deployed in Cloud, a parameter displays in the backup action
logs that indicates HypervisorMode: VMC. When the checkbox is not
selected, the parameter indicates HypervisorMode: vSphere.

7. Click OK.

VMware vCenter server management 41

Deploy the vProxy appliance and configure the NetWorker datazone

Edit a vCenter server using VMware View in NMC

You can also use VMware View in NMC's NetWorker Administration window to edit
a vCenter server that has been registered with NetWorker to update the credentials
stored in the vCenter resource.
Procedure
1. In the left pane of the Protection window, expand VMware VIew to view the
vCenter servers.
2. Right-click the desired vCenter server and select Modify vCenter.
The Modify vCenter dialog displays, with the Hostname field greyed out as
this field cannot be changed in this dialog.
3. In the Username field, specify a new vCenter user account that has permissions
to perform backups.
4. In the Password field, specify the password for this vCenter user account.
5. If the vCenter server is deployed in the Cloud and this option is currently
unselected, select the Deployed in Cloud checkbox.

Note

When you select Deployed in Cloud, a parameter will appear in the backup
action logs that indicates HypervisorMode: VMC. When the checkbox is not
selected, the parameter indicates HypervisorMode: vSphere.

6. Click OK.
Results
The changes will appear automatically in the visual representation of the vCenter in
the right pane of VMware View.

Note

If you want to delete a vCenter resource from NetWorker, right-click the vCenter
under VMware View and select Remove.

Add the vCenter server using the NetWorker Management Web UI

You can use the NetWorker Management Web UI to add a vCenter server to perform
data protection of vProxy virtual machines and objects, edit an existing vCenter
server's configuration options, or delete a vCenter server. To add the vCenter server,
perform the following.
Procedure
1. If not already logged in to the NetWorker Management Web UI, open a web
browser and type an address that points to the NetWorker server or NetWorker
Management Console IP and indicates nwui, for example, https://<NetWorker
server IP address>:9090/nwui.

The NetWorker login page displays.

2. In the NetWorker login page:
a. Type the Username and password credentials for the administrator user.
b. Type the NetWorker server IP address.

42 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

c. Type the port that will be used for communication between the NetWorker
server and the vCenter server.
d. Click Log in.
The landing page displays options for Monitoring, Protection, and Recovery in
the left pane.
3. Select Protection > VMware vCenters.
4. In the Protection window's VMware vCenters pane, click the + icon.
The Add vCenter dialog displays.
5. In the Hostname field, specify the FQDN or IP address of the vCenter server.
6. In the Username field, specify a vCenter user account that has permissions to
perform backups.
7. In the Password field, specify the password for the vCenter user account.
8. If the vCenter server is deployed in the Cloud, select the Deployed in Cloud
checkbox.

Note

When you select Deployed in Cloud, a parameter will appear in the backup
action logs that indicates HypervisorMode: VMC. When the checkbox is not
selected, the parameter indicates HypervisorMode: vSphere.

9. Click Save.
An entry for the added vCenter server will appear automatically in the
Protection window's VMware vCenters pane. If an entry for the added
vCenter does not appear, click the Refresh icon. You can also use the Refresh
icon to refresh the vCenter inventory.
Results
When you select one of the available vCenter resources, the vCenter inventory
displays in the right pane of the window in a tree structure that allows you to view all
virtual machines and entities, and select individual items to view the entity's
properties. Additionally, you can toggle a switch to displays all entities (protected and
unprotected) in the tree, display only entries that are currently protected by a policy,
or display only unprotected entities. An entity that is already protected appears blue
and bolded.

Edit a vCenter server using the NetWorker Management Web UI

You can also use the NetWorker Management Web UI to edit a vCenter server that
has been registered with NetWorker to update the credentials stored in the vCenter
resource.
Procedure
1. Select Protection > VMware vCentersin the left pane.
2. In the Protection window's VMware vCenters pane, click the + icon.
The Edit vCenter dialog displays, with the Hostname field greyed out as this
field cannot be changed in this dialog.
3. In the Username field, specify a new vCenter user account that has permissions
to perform backups.
4. In the Password field, specify the password for this vCenter user account.

Add the vCenter server using the NetWorker Management Web UI 43

Deploy the vProxy appliance and configure the NetWorker datazone

5. If the vCenter server is deployed in the Cloud and this option is currently
unselected, select the Deployed in Cloud checkbox.

Note

When you select Deployed in Cloud, a parameter will appear in the backup
action logs that indicates HypervisorMode: VMC. When the checkbox is not
selected, the parameter indicates HypervisorMode: vSphere.

6. Click Save.

Results
The changes will appear automatically in the VMware vCenters pane. If the changes
do not appear, click the Refresh icon.

Note

If you want to delete a vCenter resource from NetWorker, select the entry in the
VMware vCenters pane and click the Delete icon.

Configuring and registering the vProxy appliance

Networker provides multiple options to configure and register a deployed vProxy
appliance:
l The NMC NetWorker Administration window's VMware Proxy Configuration
wizard.
l The NetWorker Management Web UI.

Configure and register the vProxy in NMC

To complete the configuration of a vProxy OVA that was deployed on an ESXi host or
a vCenter server, use the NMC NetWorker Administration window's VMware Proxy
Configuration wizard wizard.
Note that you can also use the procedure described in the section Additional method
to add and configure the vProxy in NMC.
Procedure
1. Log in to the NMC GUI as an administrator of the NetWorker server.
2. On the taskbar, click the Enterprise icon .
3. In the navigation tree, highlight a host:
a. Right-click NetWorker.
b. Select Launch Application. The NetWorker Administration window
appears.
4. On the taskbar, click the Devices button .
5. In the Device window's left navigation pane, right-click VMware Proxies and
select New VMware Proxy Wizard.
The VMware Proxy Configuration wizard wizard opens on the Select the
Configuration Method page.
6. On the Select the Configuration Method page, select Register VMware
Proxies, and then select the vCenter/ESXi server. Click Next.

44 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

The Select the VMware Proxies to Configure and Register page displays. On
this page, the VMware Proxy Selection pane displays the location of the
deployed but unregistered vProxy appliance(s) within the vCenter/ESXi server.
7. Select the checkbox next to the vProxy appliance(s) you want to configure.
8. (Optional) If you want to override the common configuration options for the
selected vProxy, click the Edit button to open the Configure VMware Proxy
dialog. When finished, click OK to save the settings.
9. Click Next.
The VMware Proxies Configuration and Registration Summary page
displays.
10. Verify that the details are correct, and then click Configure.
Results
The jobs created for all vProxy registrations display in a table on the Check Results
page, where you can view the status, as well as the logs, for each entry. If you want to
close the wizard, you can also monitor the progress in the Monitoring pane of the
Devices window. To view the details of the job at any time, right-click an entry in the
Monitoring pane and select View Log.

Additional method to add and configure the vProxy in NMC

You can also use the following method in NMC to add and configure the deployed
VMware proxy host as a device on the NetWorker server. Note that this procedure is
not required if you already configured the vProxy by using the VMware Proxy
Configuration wizard.
Procedure
1. Log in to the NMC GUI as an administrator of the NetWorker server.
2. On the taskbar, click the Enterprise icon .
3. In the navigation tree, highlight a host:
a. Right-click NetWorker.
b. Select Launch Application. The NetWorker Administration window
appears.
4. On the taskbar, click the Devices button .
5. In the expanded left navigation pane, right-click VMware Proxies and select
New.
The Create NSR VMware Proxy dialog displays.
6. On the General tab, specify the FQDN of the vProxy appliance in the Name
field.
7. On the Configuration tab, configure the following options:
a. From the vCenter menu, select the vCenter server on which you deployed
the vProxy appliance.
b. In the User ID field, specify the admin user account.
c. In the Password field, specify the password for the admin user account on
the vProxy appliance. The default password is a3dp@m8n.
d. Specify a value in the Maximum NBD sessions or Maximum hotadd
sessions attribute, using the guidelines in the section "Performance and
Scalability."

Configure and register the vProxy in NMC 45

Deploy the vProxy appliance and configure the NetWorker datazone

l Maximum NBD sessions—Defines the maximum virtual machine

sessions that the vProxy appliance supports when you use the NBD
transport. Datastores should be defined in the vProxy properties when
using this setting to restrict NBD to these datastores only.
l Maximum hotadd sessions—Defines the maximum number of virtual
disks that NetWorker can concurrently hotadd to the vProxy appliance.
The default value is 13. The maximum value for this attribute is 25.

When specifying the maximum sessions value for the transport modes,
ensure that at least one transport mode is set to a value greater than 0. If
you want to enable only one of the transport modes, set the maximum
sessions for the transport mode you do not want to use to 0.
8. Click OK.

Add and configure the vProxy in the NetWorker Management Web UI

After deploying the OVA for the vProxy host, perform the following steps to add and
configure the vProxy by using the NetWorker Management Web UI.
Before you begin
Before adding the vProxy, ensure that you add the vCenter server by using the steps
in the section Add the vCenter server using the NetWorker Management Web UI.
Procedure
1. In the NetWorker Management Web UI, select Protection in the left pane, and
then select VMware Proxies.
The VMware Proxies pane opens on the Proxies tab, which displays any
vProxies that have already been configured. You can choose to display hidden
columns by clicking the blue icon in the lower left corner of the table.
2. In the Proxies tab, click the + icon and select Actions > Add Proxies.
3. On the Selection page, ensure that the correct vCenter is selected.
All vProxies in that vCenter inventory will display.
4. Use the Select Proxies field to select one or more vProxies, and then click
Next.
5. On the Configuration page, configure the host names for the vProxies you
want to register and specify the following configuration options:
a. Select the vCenter server on which you deployed the vProxy appliance.
b. Specify the admin user account.
c. Specify the password for the admin user account on the vProxy appliance.
The default password is a3dp@m8n.
d. Specify a value in the Maximum NBD sessions or Maximum hotadd
sessions attribute, using the guidelines in the section "Performance and
Scalability."
l Maximum NBD sessions—Defines the maximum virtual machine
sessions that the vProxy appliance supports when you use the NBD
transport. Datastores should be defined in the vProxy properties when
using this setting to restrict NBD to these datastores only.
l Maximum hotadd sessions—Defines the maximum number of virtual
disks that NetWorker can concurrently hotadd to the vProxy appliance.
The default value is 13. The maximum value for this attribute is 25.

46 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

When specifying the maximum sessions value for the transport modes,
ensure that at least one transport mode is set to a value greater than 0. If
you want to enable only one of the transport modes, set the maximum
sessions for the transport mode you do not want to use to 0.
6. Click Finish.
Results
When vProxy registration is initiated, a notification displays at the top of the window
that a request was submitted. You can monitor the status and progress of the
registration from the Tasks tab on this page.
Once registration is complete, you can use the vProxy for backups of VMware
protection policies. You can also edit the configuration settings for the vProxy by
clicking the Edit icon, or remove the vProxy by clicking the Delete icon.

Installing the vCenter plug-in

After you add the vCenter host, install either the HMTL5 or flash-based vCenter plug-
in to enable virtual machine backup and recovery in the vSphere Client or vSphere
Web Client.
NetWorker provides two options to install the vCenter plug-in:
l The NetWorker Management Web UI.
l VMware View in NMC's NetWorker Administration window.

Install the vCenter plug-in using VMware View in NMC

You can also use VMware View in NMC to install either the HMTL5 or flash-based
vCenter plug-in to enable virtual machine backup and recovery in the vSphere Client
or vSphere Web Client. Perform the following steps.
Procedure
1. In the NetWorker Administration window, click Protection.
2. In the left navigation pane, expand the NetWorker server and click VMware
View.
3. In VMware View, right-click on the vCenter you added and select Install
vCenter plugin.
The vCenter Plugin Install dialog displays.

Installing the vCenter plug-in 47

Deploy the vProxy appliance and configure the NetWorker datazone

Figure 3 Install vCenter Plugin in NMC

4. If a security warning appears, click Continue to dismiss the warning.

5. Select the Plugin Type that you want to install. HTML5 will install the Dell
EMC NetWorker interface in the vSphere Client, which is introduced in
NetWorker 18.1. FLASH will install the VM Backup and Recovery interface in
the vSphere Web Client, which was introduced in NetWorker 9.1.
6. Provide the required HTTP and HTTPS ports that are configured for the
vCenter server, or leave the default values 80 and 443.
7. Click Install.
Results
When the vCenter plug-in is validated, log in to the vSphere Client for the vCenter to
verify the installation. If the installation was successful, depending on the plug-in type
selected an entry for Dell EMC NetWorker or VM Backup and Recovery appears in
the Menu drop-down in the task bar, as shown in the following, and also appears in
the left navigation pane when you select Home.
Figure 4 vCenter plug-in for Dell EMC NetWorker in the vSphere Client

48 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Note

If you installed the HTML-5 based plug-in, you can use the vcui log file available
at /nsr/authc/logs/vcui.log to assist with troubleshooting issues with the Dell
EMC NetWorker interface. If you installed the flash-based plug-in, you can use the
ebr-server log file available at /nsr/authc/logs/ebr-server.log to assist
with troubleshooting issues with the VM Backup and Recovery interface.

Remove and reinstall the HTML5-based vCenter plug-in from the vSphere Client
In vSphere version 6.5 and later and NetWorker 18.1, the html-5 based vCenter plug-in
appears as Dell EMC NetWorker in the vSphere Client. If you need to remove the
HTML5-based plug-in and then reinstall the plug-in, perform the following steps.
Procedure
1. Stop the vSphere Client services.
2. Log into vCenter Server's MOB at http://vcenter-server/mob.
3. Click the content link.
4. Click the ExtensionManager link.
5. Click the UnregisterExtension link.
6. Enter the value com.dell.emc.nw and click the Invoke Method link.
7. Enter the value com.emc.networker.backup and click the Invoke Method link.
8. Enter the value com.emc.networker.recover and click the Invoke Method
link.
9. On the vCenter server, manually remove the plug-in from the /vsphere-
client-serenity folder. The path is /etc/vmware/vsphere-
client/vc-packages/vsphere-client-serenity on Linux, and C:
\ProgramData\VMware\vCenterServer\cfg\vsphere-client\vc-
packages\vsphere-client-serenity on Windows.
10. Restart the vSphere Client services.
11. Perform the steps in the section Install the vCenter plug-in for the vSphere
Client to re-install the HTML5-based plug-in, and verify that the Dell EMC
NetWorker interface appears in the vSphere Client.

Remove the flash-based vCenter plug-in from the vSphere Web Client
In NetWorker 9.2.x and earlier versions, the vCenter plug-in for vProxy backup and
recovery is a flash-based plug-in that appears as VM Backup and Recovery in the left
pane of the vSphere Web Client. vSphere versions 6.5 and later and NetWorker 18.1
support both this plug-in and the html-5 based vCenter plug-in that appears as Dell
EMC NetWorker in the vSphere Web Client. If upgrading to NetWorker 18.1 and you
no longer require the flash-based plug-in, perform the following steps in order to
manually remove VM Backup and Recovery from the vSphere Web Client.
Procedure
1. Stop the vSphere Web Client services.
2. Log into vCenter Server's MOB at http://vcenter-server/mob.
3. Click the content link.
4. Click the ExtensionManager link.
5. Click on the UnregisterExtension link.

Install the vCenter plug-in using VMware View in NMC 49

Deploy the vProxy appliance and configure the NetWorker datazone

6. Enter the value com.emc.networker and click the Invoke Method link.
7. Enter the value com.emc.networker.backup and click the Invoke Method link.
8. Enter the value com.emc.networker.recover and click the Invoke Method
link.
9. On the vCenter server, manually remove the plug-in from the /vsphere-
client-serenity folder. On vCenter 6.0 and 6.5, the path is /etc/
vmware/vsphere-client/vc-packages/vsphere-client-serenity
on Linux, and C:\ProgramData\VMware\vCenterServer\cfg\vsphere-
client\vc-packages\vsphere-client-serenity on Windows.
10. Restart the vSphere Web Client services.

Install the vCenter plug-in using the NetWorker Management Web UI

You can use the NetWorker Management Web UI to install either the HMTL or flash-
based vCenter plug-in to enable virtual machine backup and recovery in the vSphere
Client or vSphere Web Client. Perform the following steps.
Procedure
1. Select Protection > VMware vCentersin the left pane.
2. In the Protection window's VMware vCenters pane, click the Install icon.
The Install vCenter Plugin dialog displays.
3. Select the Plugin Type that you want to install. HTML will install the Dell EMC
NetWorker interface in the vSphere Client, which is introduced in NetWorker
18.1 for vSphere version 6.5. Flash will install the flash-based VM Backup and
Recovery interface in the vSphere Web Client, which was introduced in
NetWorker 9.1 for vSphere versions 6 and earlier.
4. Provide the required HTTPS port that is configured for the vCenter server, or
leave the default value 443.
5. Type the username and password for the NetWorker administrator user.
6. Click Install.
Results
When the vCenter plug-in is validated, log in to the vSphere Client for the vCenter to
verify the installation. If the installation was successful, depending on the plug-in type
selected an entry for Dell EMC NetWorker or VM Backup and Recovery appears in
the Menu drop-down in the task bar, as shown in the following, and also appears in
the left navigation pane when you select Home.

50 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Figure 5 vCenter plug-in for Dell EMC NetWorker in the vSphere Client

Note

If you installed the HTML-5 based plug-in, you can use the vcui log file available
at /nsr/authc/logs/vcui.log to assist with troubleshooting issues with the Dell
EMC NetWorker interface. If you installed the flash-based plug-in, you can use the
ebr-server log file available at /nsr/authc/logs/ebr-server.log to assist
with troubleshooting issues with the VM Backup and Recovery interface.

Enable the Microsoft VM App Agent for SQL Server

application-consistent protection
The Microsoft Virtual Machine Application Agent (MSVMAPPAGENT) is a component
of the vProxy data protection solution that is bundled with the vProxy appliance OVA.
MSVMAPPAGENT is automatically deployed by the vProxy during a virtual machine
application-consistent backup and, if required, when restoring Microsoft SQL
databases and SQL instance backups to running virtual machines. After installation,
the MSVMAPPAGENT package appears in the Windows installer Add-Remove
programs list.
The MSVMAPPAGENT allows for advanced application data protection of workloads
residing on a VMware ESXi server. This includes adding SQL virtual machines to an
advanced application-consistent protection policy to perform the following operations:
l SQL Server FULL backup to Data Domain—Configure a NetWorker policy's
VMware backup action with the Advanced Application Consistency option to
perform SQL Server backup to a Data Domain device as part of a VMware image-
level backup. The SQL Server FULL backup is performed during the in-guest
quiesce by VMware Tools. After running the policy, the catalog and index
information for the SQL server backup is stored on the Data Domain device. When
the backup is performed as part of the VMware image-level backup, the SQL data
files are backed up as part of the VMDKs during the vProxy image backup. The
sections Creating a VMware backup action and Creating an action for Microsoft
SQL Server application-consistent protection provide more information.
l Transaction log backup—When configuring a NetWorker policy's workflow and
VMware backup action with the Advanced Application Consistency option, select
Transaction log backup to enable transaction log backups for SQL Instances
running in the virtual machine, and set the Interval attribute in the backup policies
workflow properties to specify the frequency of backups. Backups are written

Enable the Microsoft VM App Agent for SQL Server application-consistent protection 51
Deploy the vProxy appliance and configure the NetWorker datazone

directly to Data Domain under the SDSF backup folder that was created by the
NetWorker save set session. Transaction log backup is only performed for
databases in the proper state, otherwise databases are skipped. The sections
Creating a VMware backup action, Creating a workflow provide more information.
l Restore of SQL Server instance or individual SQL Server databases—The Dell
EMC Data Protection Restore Client includes an App mode that allows you to
restore an entire SQL Server instance to the original virtual machine and original
instance, and restore individual SQL Server databases to the original database on
the original virtual machine, to multiple instances on the same virtual machine, or
to an alternate location (different virtual machines/SQL instances on the same or
a different vCenter), as well as the ability to roll-forward transaction log backups.
The section Restoring SQL Server application-consistent backups provides more
information.
During advanced application-consistent backup for both SQL Server FULL backup and
transaction log backup, vProxy installs or upgrades the vProxy Agent and
MSVMAPPAGENT software packages. On a new virtual machine without these
software packages installed, the vProxy Agent uses the VM Administrator Credentials
from the backup action to install the vProxy Agent, using the vCenter VIX API to copy
packages into the guest virtual machine and run the install. Once the vProxy Agent is
installed in the virtual machine, vProxy communicates with the vProxy Agent to install
the MSVMAPPAGENT package.
On a system with vProxy and MSVMAPPAGENT already installed, vProxy performs a
version check of the MSVMAPPAGENT by running the
Msvmagent_discovery.exe program to report the installed program version and, if
necessary, perform an upgrade if the vProxy software repository contains a later
version.

Note

Ensure that you manually uninstall in-guest agents (VM app agent for Microsoft
Applications) from an alternate virtual machine that is not protected by a SQL
application-consistent backup workflow. Also, if you are restoring to an alternate
virtual machine that is not protected by a SQL application-consistent workflow, note
that the agents will not be automatically uninstalled once the restore is complete. If
you want to remove these agents, you must manually uninstall the agents.

The following table provides a list of the MSVMAPPAGENT binaries that are called by
the vProxy, and the operations these binaries perform.
Table 7 MSVMAPPAGENT binaries called by vProxy

Binary Purpose When called

Msvmagent_discovery.exe Provides functions for listing program Called by vProxy to report agent version
version and for validating that SQL is and determine if an upgrade is required.
installed and for listing SQL Instances Also called by vProxy to validate that
and databases. SQL Server services are running in the
virtual machine. Also called by vProxy to
report running SQL instances and
databases to support SQL alternate
restore selection.

52 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Table 7 MSVMAPPAGENT binaries called by vProxy (continued)

Binary Purpose When called

Note

If Msvmagent_discovery.exe does
not find running SQL Server services,
the program returns a failure to the
vProxy and the overall NetWorker
Application Consistent backup workflow
cannot proceed. To resolve the issue,
remove virtual machines that do not
have SQL from the NetWorker
Application Consistent workflow. You
can also use the action logs to diagnose
the failure, and contact Dell EMC
support if required.

Msvmagentcatsnap.exe Catalogs the SQL VSS Full backup that Called by vProxy once the virtual
was performed by VMware Tools as an machine image snapshot has completed.
App Agent VSS Full backup of SQL
Server instances. Catalog is written to
Data Domain.

Msvmagent_appbackup.exe Performs transaction log backup. Called by vProxy for transaction log
backup workflows.
The Msvmagent_appbackup.exe
program will back up all SQL instances in
the virtual machine.
Msvmagent_appbackup.exe
performs transaction log backup only,
and does not create a virtual machine
image backup.

Msvmagent_snapshotrestore.exe Performs restore of SQL VSS Full Called by vProxy during restore of SQL
backup. Database FULL backup.
Prior to the restore, the virtual machine
image backup is mounted on the target
virtual machine. The
Msvmagent_snapshotrestore.exe
copies the VSS manifest documents
from the backup, and uses those
documents to perform a VSS-aware
restore of the SQL database. The SQL
database files are copied from the
mounted backup VMDK to the original
location of the database, and during the
VSS post restore, the SQL VSS Writer
completes recovery of the backup. If
transaction logs are to be restored, or if
the NORECOVERY option has been
specified, the database will be left in a
NORECOVERY state. The
msvmagent_snapshotrestore.exe

Enable the Microsoft VM App Agent for SQL Server application-consistent protection 53
Deploy the vProxy appliance and configure the NetWorker datazone

Table 7 MSVMAPPAGENT binaries called by vProxy (continued)

Binary Purpose When called

command also supports SQL Alternate
restore and instructs SQL the SQL
instance to be restored and to change
database name and file locations as
selected by the customer.

Msvmagent_apprestore.exe Performs restore of individual SQL Called by vProxy during restore of the
transaction log backup. transaction log backup.
For each transaction log restore,
Msvmagent_apprestore.exe
receives the Data Domain path for the
backup and performs a SQL VDI restore
of the transaction log backup. For
intermediate transaction logs, the
database is left in the NORECOVERY
state. For the final transaction log
restore, the database is either recovered
or left in the NORECOVERY state if you
specify this option. The STOPAT feature
may also be used for the final
transaction log restore if you specify this
option. The msvmagent_apprestore.exe
command also supports SQL Alternate
restore and instructs SQL the SQL
instance to be restored and to change
database name and file locations as
selected by the customer.

MSVMAPPAGENT binaries are installed to C:\Program Files\DPSAPPS

\MSVMAPPAGENT\bin. Logs are located in C:\Program Files\DPSAPPS
\MSVMAPPAGENT\log.
Software and security requirements
In order to perform SQL Server application-consistent data protection for virtual
machines, the MSVMAPPAGENT requires the following:
l TheMSVMAPPAGENT runs under the SYSTEM account for data protection
operations. Configure all SQL Server instances in the virtual machine to grant NT
AUTHORITY\SYSTEM account rights to perform SQL database backup and
recovery operations:
Add SYSTEM account to SQL logins.
Grant SYSTEM account the sysadmin role.
l Network connectivity, host name resolution, and firewall ports between the Data
Domain device and the virtual machines that are part of SQL Server application-
consistent protection policies and restore to alternate operations. This
connectivity is required to allow MSVMAPPAGENT to perform client direct
operations to Data Domain.
l VMware vCenter server version 6.5 and later.
l VMware ESXi server version 6.5 and later.
l VMware Tools version 10.1 and later.

54 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

l Enable the UUID attribute (disk.EnableUUID=TRUE) in the vSphere Client.

l The virtual machine must use SCSI disks only, and the number of available SCSI
slots must at least match the number of disks. For example, a virtual machine with
7 disks will only require one SCSI controller, but a virtual machine with 8 disks will
require 2 SCSI controllers.
l The vProxy requires live network connectivity to the ESXi where the targeted SQL
virtual machine resides.

Note

The MSVMAPPAGENT does not require installation of the NetWorker client.

The following table provides a list of special characters known to be supported in SQL
database names for English and non-English locales.
Table 8 Supported characters in SQL database names

Special character FULL and transaction log FULL and transaction log
backup restore
~ Tilde Supported Supported

- Hyphen Supported Supported

! Exclamation mark Supported Supported

{ Open curly bracket Supported Supported

% Percentage Supported Supported

} Close curly bracket Supported Supported

) Close parenthesis Supported Supported

( Open parenthesis Supported Supported

` Accent grave Supported Supported

@ At the rate Supported Supported

# Hash Supported Supported

_ Underscore Supported Supported

& Ampersand Supported Supported

^ Caret Supported Supported

\ Backslash Supported Supported

' Apostrophe Supported Supported

Note

Restore to an alternate
location for a SQL database
with an apostrophe in the file
name or destination file path
will fail to restore.

$ Dollar Supported Supported

: Colon Supported Supported

Enable the Microsoft VM App Agent for SQL Server application-consistent protection 55
Deploy the vProxy appliance and configure the NetWorker datazone

Table 8 Supported characters in SQL database names (continued)

Special character FULL and transaction log FULL and transaction log
backup restore
. Period Supported Supported

Unsupported features and configurations

The following features and configurations are not supported for SQL application-
consistent protection:
l The MSVMAPPAGENT only supports stand-alone SQL Server instances, and does
not support SQL Server Always-On Availability Group and SQL Server Clustered
Failover instances.
l The MSVMAPPAGENT does not support interoperability with other backup
agents, including SQL backup products from Dell EMC. If another backup product
is running at the same time as MSVMAPPAGENT, the MSVMAPPAGENT has
safeguards to prevent issues. For example, if another product is performing in-
guest backups, MSVMAPPAGENT may skip databases for transaction log
backups.
l If using the VM Backup and Recovery user interface in the vSphere Web Client
for vSphere versions earlier than 6.5, backup and recovery operations are not
supported for SQL Server advanced application-consistent protection policies. For
SQL backups, perform these operations from the NMC NetWorker
Administration window or the Dell EMC NetWorker user interface in the
vSphere Client. For SQL recoveries, perform these operations from the Dell EMC
Data Protection Restore Client.
Additionally, the following items are not supported due to VMware restrictions and
feature limitations:
l Changing pools between backup actions, for example, between a SQL full and
transaction log backup.
l Application-consistent quiescing for virtual machines with IDE disks.
l Dynamic disks on the virtual machine.
l Read-only volumes mounted on the SQL virtual machine.
l VMware encrypted virtual machines.
l VMware Fault Tolerant virtual machines.
l RDM storage.
The vProxy appliance performs validation of the environment for these VMware
restrictions. If validation fails, the VMware policy with SQL Server application-
consistent data protection will not run.

Additional vProxy backup configuration options

The following section provides additional configuration options for vProxy backups.

56 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Configure a backup to support VMware encryption

NetWorker 18.1 supports encrypted virtual machine backups. When configuring a
virtual machine backup with VMware encryption, perform the following steps.
Before you begin
Review the known limitations for configuring a backup to support VMware encryption.
To backup or restore encrypted virtual machines, ensure that the vProxy appliance is
also encrypted, and that the vProxy is manually mapped to the backup policy.
The VMware vSphere Security Guide provides more information about virtual machine
encryption.
Procedure
1. Establish encryption for the virtual machine.
a. Set up the Key Management Service (KMS).
b. Create a VM encryption policy.
c. Assign the encryption policy to the virtual machine(s) you want to encrypt.
2. Encrypt the vProxy appliance.
3. Open the /opt/emc/vproxy/conf/VixDiskLib.config file with a Linux
text editor.
4. In the file, search for vixDiskLib.transport.hotadd.NoNFCSession and change
the value to 0.
Changing this value to 0 overrides a VMware VDDK bug that inhibits hot-adding
an encrypted virtual machine. The VMware Release Notes provide more
information.
5. Save and close the file.
6. Run the following:
systemctl restart vbackupd.service
7. Set the following additional permissions for the vCenter user account role,
which is described in the section Create a customized role:
Cryptographic operations > Add disk

Cryptographic operations > Direct access

Cryptographic permissions- Register VM

VMware encryption support limitations

The following limitations apply to backups with VMware encryption enabled.
l As a result of disabling NoNFCSession, backup and restore in VMware Cloud on
Amazon Web Services (AWS) is not supported. This VMware limitation is
addressed in the VDDK update.
l When restoring from an encrypted virtual machine backup, the restored data is
unencrypted.
l Restoring virtual machines requires that the target vCenter is configured for the
same Key Management Service (KMS) host as the source vCenter.

Configure a backup to support VMware encryption 57

Deploy the vProxy appliance and configure the NetWorker datazone

l Application-consistent quiesce snapshot backups on an encrypted virtual machine

will fail back to a file system-consistent snapshot. This process generates an error
message in vCenter, which can be ignored. This is a VMware limitation.
l When restoring a virtual machine as a new image, by default, new virtual machines
are not encrypted. If you want to apply encryption to the new virtual machine,
apply the required storage policy.
In cases where a boot order other than the default was implemented before the
image-level backup was performed, the original boot order is not restored. In this
instance, you must select the correct boot device after the restore completes.
Alternatively, you can enter the non-default boot order to the VMX file so that the
restored virtual machine starts without any reconfiguration. This limitation does
not affect virtual machines that use the default boot order.

Configure a backup to support vSAN encryption

NetWorker 18.1 supports all backup and recovery functionality for encrypted vSAN
virtual machines, including the restore of an encrypted vSAN virtual machine to a
different vCenter that has a non-encrypted datastore.
When performing backups or restores of virtual machines residing on vSAN
datastores, it is highly recommended to deploy the vProxy on a vSAN datastore. A
vProxy deployed on any one vSAN datastore can be used for backing up virtual
machines from other vSAN or non-vSAN datastores (encrypted or non-encrypted) by
using hotadd or nbdssl transport modes, as applicable. Both Capacity and
Performance Optimization modes are fully supported for vSAN encrypted virtual
machines.
The VMware Administering VMware VSAN Guide provides more information about VSAN
encryption.
When configuring a virtual machine backup with vSAN encryption, perform the
following steps.
Procedure
1. Set the following permissions for the vCenter user account role, which is
described in the section Create a customized role:
Cryptographic operations > Add disk

Cryptographic operations > Direct access

2. Create the backup group.

Note

To back up the vSAN virtual machine, use the vProxy deployed in the vSAN
datastore.

Enabling or disabling Changed Block Tracking

The vProxy appliance uses changed block tracking (CBT) automatically upon the first
virtual machine backup so that only changed disk areas on the virtual machine get
backed up. Some virtual machines, however, do not support CBT and you may be
required to disable CBT for those virtual machines.
A vCenter administrator can control the application of CBT by using the custom field
EMC vProxy Disable CBT. You can set this custom field to true to disable CBT, or
false to enable CBT. If you do not set this field for a virtual machine, or the field is not
present, CBT is enabled by default for that virtual machine.

58 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

To set CBT for virtual machines, perform the following:

1. Log into the vSphere Client (vSphere versions 6 and earlier) or vSphere Web
Client (vSphere versions 6.5 and later) as an administrator.
2. Click on a virtual machine in the vCenter tree, and then click the Summary tab.
3. Edit the virtual machine attributes:
l In vSphere versions 6.x and earlier, click Edit in the Annotation box.
l In vSphere versions 6.5 and later, click Edit under Custom Attributes.
4. Locate the EMC vProxy Disable CBT field, or create a string for EMC vProxy
Disable CBT. The string must match the field name exactly and is case-sensitive.
5. Set the value to true to disable CBT on the virtual machine, or to false (or leave
the field blank) to enable CBT on the virtual machine. Setting or resetting the field
for one virtual machine does not affect the other virtual machines in the vCenter.
6. Refresh VMware View in the NMC NetWorker Administration window.
Fixing CBT if corrupted on virtual machine
If CBT becomes corrupted on the virtual machine, warnings similar to the following
appear in the backup logs:

WARN: Change block tracking needs to be reset.

WARN: Change Block Tracking could not be reset, causing full backup:
Second attempt failed.
NOTICE: Change block tracking cannot be reset by proxy. Please
remediate VM.

If these messages appear, you can use PowerCLI commands to disable and then
enable CBT without powering off the virtual machines as described in the VMware
knowledgebase article at https://kb.vmware.com/selfservice/search.do?
cmd=displayKC&docType=kc&docTypeID=DT_KB_1_1&externalId=1031873, or
perform the following steps to clean up CBT:
1. Power down the virtual machine.
2. Remove CBT flags.
3. Delete CTK files from the datastore.
4. Power ON the virtual machine.

Creating a dedicated vCenter user account and VM Backup

and Recovery role
It is strongly recommended that you set up a separate vCenter user account at the
root level of the vCenter that is strictly dedicated for use with NetWorker VMware
Protection. Use of a generic user account such as “Administrator” might make future
troubleshooting efforts difficult as it might not be clear which “Administrator” actions
are actually interfacing, or communicating, with the NetWorker server. Using a
separate vCenter user account ensures maximum clarity if it becomes necessary to
examine vCenter logs.

Create vCenter user account

Procedure
1. From a web browser, type the following:
https://<IP_address_vCenter_Server>:5480

Creating a dedicated vCenter user account and VM Backup and Recovery role 59
Deploy the vProxy appliance and configure the NetWorker datazone

The VMware vCenter Server Appliance login page appears.

2. Enter the vCenter root user credentials to log in.
3. In the VMware vCenter Server Appliance Console, click the Summary tab,
and then click the Stop button next to the Server service in the vCenter pane.
4. Click the SSO tab, and then select Embedded from the SSO deployment type
drop-down list.
5. Assign a password, and click Save settings.
6. Click the Summary tab, and then click the Start button next to the Server
service in the vCenter pane.
7. Log out of the session.
8. From a web browser, enter the following to connect to the vSphere Web Client:
https://<IP_address_vCenter_Server>:9443/vSphere-client/

9. Login as user [email protected] with the password you created in

step 5.
10. Navigate to Home > Administration > SSO Users and Groups.
11. On the Users tab, click the green +.
The New User window appears.
12. In the Username field, specify a username (for example, VM Backup and
Recovery).
13. In the Password and Confirm Password fields, specify a password.
You can leave the First name, last name and password fields blank.
14. Click OK.

Create a customized role

Procedure
1. In the vSphere Web Client, open Administration > Role Manager and click on
the green +.
The Create Role dialog appears.

2. Type the name of this role (for example, Admin1).

3. Select all the privileges listed in the following table and click OK. This vCenter
user account must have these privileges at a minimum.

Table 9 Minimum required vCenter user account privileges

Setting vCenter 5.5 and later required

privileges
Alarms l Create alarm
l Modify alarm

Datastore l Allocate space

l Browse datastore
l Configure datastore

60 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Table 9 Minimum required vCenter user account privileges (continued)

Setting vCenter 5.5 and later required

privileges

l Low level file operations

l Move datastore
l Remove datastore
l Remove file
l Rename datastore

Extension l Register extension

l Unregister extension
l Update extension

Folder l Create folder

Global l Cancel task

l Disable methods
l Enable methods
l Licenses
l Log event
l Manage custom attributes
l Settings
l Set custom attribute

Host l Configuration > Storage partition

configuration

Note

Not applicable to vCenter 5.5.

Network l Assign network

l Configure

Resource l Assign virtual machine to resource pool

l Migrate powered off virtual machine
l Migrate powered on virtual machine

Sessions l Validate session

Tasks l Create task

l Update task

vApp l Export
l Import
l vApp application configuration

Create a customized role 61

Deploy the vProxy appliance and configure the NetWorker datazone

Table 9 Minimum required vCenter user account privileges (continued)

Setting vCenter 5.5 and later required

privileges
Virtual Machine

Configuration l Add existing disk

l Add new disk
l Add or remove device
l Advanced
l Change CPU count
l Change resource
l Configure managed by
l Disk change tracking
l Disk Lease
l Extend virtual disk
l Host USB device
l Memory
l Modify device settings
l Raw device
l Reload from path
l Remove disk
l Rename
l Reset guest information
l Set annotation
l Settings
l Swapfile placement
l Upgrade virtual machine compatibility

Guest Operations l Guest operation modifications

l Guest operation program execution
l Guest operation queries

Interactions l Configure CD media

l Console interaction
l Device Connection
l Guest operating system management by
VIX API
l Power off
l Power on
l Reset
l VMware Tools install

62 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Table 9 Minimum required vCenter user account privileges (continued)

Setting vCenter 5.5 and later required

privileges
Inventory l Create new
l Register
l Remove
l Unregister

Provisioning l Allow disk access

l Allow read-only disk access
l Allow virtual machine download
l Mark as Template

Snapshot Management l Create snapshot

l Remove Snapshot
l Revert to snapshot

vSphere Client user accounts

Before you can use the vCenter user account with NetWorker VMware Protection, or
before you can use the Single Sign-on (SSO) admin user with the vProxy appliance,
you must add these users as administrator on the vCenter root node. Users who
inherit permissions from group roles are not valid.

Note

In high-security environments, you can restrict the vCenter user account permissions
required to configure and administer the vProxy appliance. Table 9 on page 60
provides the account permission categories.

The following steps allow you to configure a VM Backup and Recovery user or SSO
admin user by using the vSphere Web Client.
Procedure
1. From a web browser, access the vSphere Web Client using the following URL:
https://<Ip_address_vCenter_server>:9443/vsphere-client/

2. Log in with administrative rights.

3. In the left panel of the vSphere Web Client window, select vCenter > Hosts
and Clusters.

vSphere Client user accounts 63

Deploy the vProxy appliance and configure the NetWorker datazone

Figure 6 Hosts and Clusters in the vSphere Web Client

4. Select the Manage tab and then click Permissions.

Note

When assigning permissions, the vSphere Web Client places the curser in the
location last used. Depending on what level was selected the last time you used
this window, permissions might not get applied to the root level of the vCenter.
For example, if the last item you selected in this window was Cluster Name,
permissions will be assigned at the Cluster level. Review carefully to ensure that
permissions get assigned at the root level of the vCenter.

5. Click the Add permission ( ) icon.

The Add Permission dialog box opens.
6. In the Users and Groups pane, click Add....
The Select Users/Groups dialog box appears.

7. From the Domain drop-down list, select domain, server, or SYSTEM-DOMAIN.

8. Select the user that will administer VM Backup and Recovery, or the SSO admin
user, and then click Add.
If the VM Backup and Recovery user belongs to a domain account, the account
appears in the format “SYSTEM-DOMAIN\admin” format. If the user name
appears in the format “admin@SYSTEM-DOMAIN”, then tasks related to the
backup job may not appear on the Running tab of the Recent Tasks window.

9. Click OK.
10. From the Assigned Role drop-down list, select the role you created.
11. Confirm that the Propagate to children box is checked.
12. Click OK.

64 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Adding a NIC for VMXNET 3 on the vProxy appliance

The following section describes how to set up a virtual network interface card (vNIC)
of type VMXNET 3 for the vProxy appliance. You can also use this procedure to swap
a NIC to VMXNET 3 on the vProxy appliance.
Before you begin
This procedure is required for custom setup using dual NIC, but is otherwise optional
for vProxy appliances unless you are swapping a NIC.
If setting up dual NIC, review the section Dual vNIC setup and configuration
requirements, and then use the following steps to configure the appliance before the
steps outlined in the section Configuring the vProxy in NetWorker.
Procedure
1. Log in to the vProxy appliance console in the vSphere Client.
2. Right-click the vProxy appliance and select Power > Shutdown Guest.
3. Add the second NIC to the vProxy appliance:
a. Right click the vProxy appliance, and then select Edit Settings. The Virtual
Machine Properties window appears.
Figure 7 Swap network for NICs in the Virtual Machine Properties window

b. (Optional, to be performed when swapping a NIC) In the Hardware tab,

select Network adapter 1 in the list, and then click Remove.
c. In the Hardware tab, click Add.
The Add Hardware wizard opens.
d. In the Device Type page, select Ethernet Adapter and click Next.

Adding a NIC for VMXNET 3 on the vProxy appliance 65

Deploy the vProxy appliance and configure the NetWorker datazone

e. In the NetWork Type page, change the value in the Adapter Type field to
VMXNET 3, and assign this vNIC to the appropriate virtual machine port
group. Select the Connect at power on checkbox if it is not selected.
Figure 8 Change Adapter Type

f. Select the appropriate virtual machine port group for the production
network/VLAN, and then click Next.
g. In the Ready to Complete page, verify the information and then click
Finish.
4. Right click the vProxy appliance and select Power > Power On.
5. Configure the second NIC on the vProxy appliance:
a. After you power on the vProxy appliance, log in as root to the vProxy
appliance Console by using the vSphere Client.
b. Type yast2 to invoke the YaST configuration tool.
c. Select Network Devices and press Enter.
The Network Devices dialog appears.
d. Select Network Settings and press Enter.
The Network Settings dialog appears.
e. In the Overview tab, select the Second Ethernet Adapter labeled eth1.
f. Use the tab key to select Edit and press Enter.
g. From the Network Card Setup, use the tab key to access Statically
assigned IP Address and select using the spacebar. Use the tab key to
select IP Address and enter the IP Address, the Subnet Mask, and the host
name of the vProxy appliance. Ensure that these settings come from the
production network/VLAN.
h. Use the tab key to select Edit, and then press Enter.
i. (Optional when setting up second NIC) From Network Settings, use the tab
key to select Overview. Use the right-arrow key to select Hostname/DNS.
Use the tab key to select and then specify the following fields:

66 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

l Host name
l Domain name for the production network
l Policy for DNS configuration
l Name Server 1 for production network
l Name Server 2 for backup network
l Domain Search for both production and backup network.

When setting up a second NIC, carefully review the following sections

including operating system routes since you may need to be define these
routes as custom routes.

j. From Network Settings, use the tab key to select Hostname/DNS.Use the
right-arrow key to select Routing, and update the routing table by setting
the Default Gateway to the gateway/address for the backup network, if not
already set.
Figure 9 Routing table with backup network gateway

k. Use the tab key to select Add to the Routing table.

l. Add the following entry to the Routing table:
l Destination: IP address for the vCenter Server
l Device: eth1
l Gateway: gateway/address for your production network
l Netmask: Same as the netmask for eth1 entered earlier

m. Use the tab key to select OK, and then press Enter.
n. Use the tab key to select Quit, and then press Enter.
6. Restart the vProxy appliance.
7. Login to the vProxy appliance and confirm that you can ping the vCenter
production network IP.
You can now proceed with registering the vProxy appliance with the NetWorker
server on the backup subnet/VLAN. This will require selecting the vCenter
server running on the production network in the drop-down.

Adding a NIC for VMXNET 3 on the vProxy appliance 67

Deploy the vProxy appliance and configure the NetWorker datazone

Dual vNIC setup and configuration requirements

This section outlines NetWorker support for enabling the vProxy appliance to support
dual vNIC. Enabling dual vNIC on the vProxy appliance can provide the following
benefits:
l You can separate the backup data traffic going to the back-end from the
production network so that backups do not negatively impact performance in your
environment.
l You can use a separate private or isolated physical network infrastructure for your
backup network and send the backup data in this isolated network unencrypted,
leading to performance gains.
l You can dedicate a NIC to backup traffic so that you do not impact production
performance if using an older host with a slower physical NIC.
Along with the configuration required when downloading and deploying the vProxy
appliance, the vProxy appliance requires the following for dual vNIC setup. Review
these items before performing the steps in the section Adding a NIC for VMXNET 3 on
the vProxy appliance:
l During deployment of the vProxy appliance, ensure that you assign an IP address
from the backup subnet/VLAN that follows the normal rules for a proxy appliance
(for example, has a DNS server, associated PTR on that DNS server, and so on).
l Before registering the vProxy appliance with the NetWorker server on the backup
subnet/VLAN, add static routes for the production network/VLAN. This is
required for communicating with the vCenter server.
l Power on the vProxy appliance, and when you log in, ensure that you can perform
nslookup for the backup subnet FQDN of the vProxy and the NetWorker server.
l In order to use Instant Access restore, emergency restore, and file-level restore
with dual NIC configured, the destination ESXi requires a VMkernel port
connected to the backup subnet/VLAN. You can configure the vmkernel port on a
separate VLAN by using the steps in the following knowledegbase article:
https://kb.vmware.com/selfservice/microsites/search.do?
language=en_US&cmd=displayKC&externalId=2001426.
l Configure the two vNICs with separate and unique subnets in order to facilitate
the direction of network traffic. All backup traffic will flow out of the first vNIC. All
production traffic (which includes vCenter Server traffic, VMTools requests used
by file-level restore, and so on) will flow out of the second vNIC. Further details
for vProxy appliance NIC connectivity are provided in the bullets below.
l Proxies with multiple NICs rely on the operating system routes and require reliable
bi-directional communications with the respective subnets on which the NICs are
configured with Data Domain systems.

Note

You may be required to define operating system routes as custom routes.

l Set up the NetWorker server with dual network adapters, with eth0 connected to
the backup subnet/VLAN and eth1 connected to the production network/VLAN.

68 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Figure 10 Backup and production traffic with dual network adapters

You can use a non-routable private address space for the subnet used for the backup
traffic/data, providing that:
l All devices/vNICs using a private IP address exist on the same physical switch, and
l There is a DNS server on the non-routed private network so that the proxies can
perform a reverse lookup for its host name.

Note

A private address space-based network is an optional example and not a requirement.

Verify vNIC connectivity

You can verify that the vNIC is associated to the correct network by running a test
using ping or traceroute against the IP of the NetWorker server and/or vCenter and
other required components. If the IP is not reachable, you may need to swap the
network for NICs.
1. Right-click the vProxy appliance and select Edit Settings.
2. in the Hardware tab of the Virtual Machine Properties window, select Network
adaptor and Network connection on the right of the screen.
3. In the Network connection page, select the correct network label.
4. Click OK to complete the configuration change.
For systems with swapped NICs or dual vNIC configurations, you can use the
proxycp.jar command line utility on the vProxy appliance to test connectivity.
To download the proxycp.jar command line utility:
1. Log into the vProxy appliance by using the vSphere Client or a putty session.
2. If required, run sudo su - to switch to the root user.
3. In a command prompt, use which curl. For example:

blrv071b219:~ # which curl

/usr/bin/curl
blrv071b219:~ #

Verify vNIC connectivity 69

Deploy the vProxy appliance and configure the NetWorker datazone

4. Run the following command:

curl -O ftp://valid_ftp_needed/software/scripts/proxycp.jar

For sites where direct download using curl is unavailable, use WinSCP to transfer
the script to the VMware Backup appliance or external proxy.
5. Change the permissions on proxycp.jar:

chmod 755 /usr/local/avamar/bin/proxycp.jar

After downloading proxycp.jar, you can use the following command tools to test
connectivity:
l proxycp.jar --vctest --dryrun—Tests connectivity to vCenter and
returns many details of the vCenter.
l proxycp.jar --testconn—connects to vCenter to perform tests at set
intervals, similar to "ping tests".
l proxycp.jar --testwebservice—Tests connectivity to the Avamar MC
SDK.
l proxycp.jar --portcheck [--timeout <Num> ] - Tests proxy
connectivity to vCenter by discovering all nodes and hosts in the environment and
then checking connectivity of each proxy to every single ESX host. Also checks
for Data Domain in the environment and checks connectivity from the proxy. If
running in a slower environment you can change the timeout value from the
default of 10 seconds to 60 seconds.
Dual NIC configuration, and particularly operating system routes, can be very complex
and require careful planning by the administrator. When complete the setup and
verified working functionality of the configuration, make note of the configuration
details including NIC Type, IPs, operating system routes and any other custom
settings since these may be required if you need to recreate the OVA for operations
such as proxy upgrades and storage failures.

Migrating policies from VMware Backup appliance to vProxy

appliance
New installations of NetWorker 18.1 use the NetWorker VMware Protection solution
with the vProxy appliance. When you upgrade from a NetWorker 9.0.x and earlier
release, you can continue to use the VMware Backup appliance, migrate to use only
the vProxy appliance, or use a combination of the VMware Backup appliance and
vProxy appliance. If you choose to use the vProxy appliance only, workflow migration
is required to convert existing VMware Backup appliance policies to vProxy appliance
policies.
This migration involves two stages—a check that occurs prior to migration to ensure
all the compatibility prerequisites are satisfied, and then the actual migration to
convert existing VMware Backup appliance protection groups and policies to the
vProxy appliance. You can initiate the policy migration by using the command line or
NMC.

Note

NetWorker does not support the migration of workflows and policies from a VMware
Backup appliance deployed in a NetWorker release previous to NetWorker 9.0 that
uses GSAN internal storage.

70 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Co-existence of the VMware Backup appliance and vProxy appliance

After upgrading to a NetWorker 9.1.x or 9.2 release and migrating from the VMware
Backup appliance to the vProxy appliance, you might still require the VMware Backup
appliance. For example, if you want to recover from a backup performed with the
VMware Backup appliance that has not expired, you must keep the VMware Backup
appliance and at least one of the VMware Backup appliance's external proxies.
If you plan to continue using the VMware Backup appliance, make note of the
following information:
l NetWorker 9.1 and later releases require the same version of the VMware Backup
appliance as NetWorker 9.0.1, which is 1.5.1.7. If you are upgrading from
NetWorker 9.0.1, you do not need to upgrade the VMware Backup appliance
version. If you are upgrading from an earlier release, for example, from NetWorker
8.2.3 with version 1.1.3.7, you will need to upgrade the VMware Backup appliance
version to 1.5.1.7 after upgrading the NetWorker server to 9.1 and later.
l Backups run with VMware Backup appliance policies cannot be recovered using
the vProxy appliance. These backups must be recovered with the VMware Backup
appliance.
l You cannot create new policies with the VMware Backup appliance. You can only
run or edit existing policies.
l You cannot run policies with VMware Backup appliance GSAN internal storage.
l Different plug-ins are available in the vSphere Web Client for VMware Backup
appliance policies and vProxy appliance policies. For the VMware Backup
appliance, this is the EMC Backup and Recovery plug-in. For the vProxy
appliance, this is the VM Backup and Recovery plug-in. The two plug-ins can co-
exist on the same vCenter.
It is recommended to migrate all VMware Backup appliance policies to the vProxy
appliance. Note that you can still use the EMC Backup and Recovery plug-in within
the vSphere Web Client for operations that are related to the backup of still-to-be
migrated VMware Backup appliance policies, or for image-level recovery of any
backups performed with the VMware Backup appliance. However, after a policy has
been migrated to the vProxy appliance, it is no longer accessible from the VMware
Backup appliance. You must manage all such migrated policies as native NetWorker
vProxy policies from NMC, or by using the VM Backup and Recovery plug-in within
the vSphere Web Client for NetWorker 9.1 and later vProxy-based policies.
Additionally, for file-level recovery in the EMC Data Protection Restore Client, you
must use vProxy appliance backups after migrating. Recovery from older backups that
were created using the VMware Backup appliance can still be performed using the
EMC Backup and Recovery plug-in, but you must retain at least one external proxy
node.
The following table provides a list of supported and unsupported VMware Backup
appliance operations in an upgraded NetWorker 9.1 and later environment.
Table 10 Supported and unsupported VMware Backup appliance operations in a NetWorker 9.1
and later environment

Supported operations Unsupported operations

l Scheduled backups of VMware Backup appliance policies l Create new VMware Backup appliance protection policies
that were created before upgrading to NetWorker 9.1 or
9.2

Co-existence of the VMware Backup appliance and vProxy appliance 71

Deploy the vProxy appliance and configure the NetWorker datazone

Table 10 Supported and unsupported VMware Backup appliance operations in a NetWorker 9.1
and later environment

Supported operations Unsupported operations

l On demand (adhoc) backups of virtual machines l Image-level recovery of VMware Backup appliance
protected by a VMware Backup appliance from NMC's backups by using the VM Backup and Recovery plug-
Protection window in in the vSphere Web Client
l On demand (adhoc) backups of virtual machines l Image-level recovery of VMware Backup appliance
protected by a VMware Backup appliance from the EMC backups by using the NMC Recovery wizard
Backup and Recovery plug-in in the vSphere Web l File-level recovery from VMware Backup appliance
Client backups by using the NMC Recovery wizard
l Edit existing VMware Backup appliance protection l File-level recovery from VMware Backup appliance
policies (for example, to modify an existing action to point
backups by using the Dell EMC Data Protection
to a different VMware Backup appliance)
Restore Client (vProxy)
l Modify the VMware Backup appliance protection group to
l Manage VMware Backup appliance policies by using the
add virtual machines to an existing group or remove
virtual machines from an existing group VM Backup and Recovery plug-in in the vSphere
Web Client
l Image-level recovery (to a new virtual machine, revert,
VMDK-level and instant access) from VMware Backup l Manage vProxy policies by using the VM Backup and
appliance backups run before or after the upgrade by Recovery plug-in in the vSphere Web Client
using the EMC Backup and Recovery plug-in in the
vSphere Web Client
l File-level recovery from VMware Backup appliance
backups run before or after the upgrade by using the Dell
EMC Data Protection Restore Client (VBA)
l Emergency restore from VMware Backup appliance
backups run before or after the upgrade
l Create checkpoints after the upgrade by running an
integrity check using the EMC Backup and Recovery
plug-in in the vSphere Web Client
l Rollback to a desired checkpoint (to checkpoints taken
after the upgrade)
l Deploy and manage VMware Backup appliance external
proxies after the upgrade by selecting a desired VMware
Backup appliance
l Resurrect VMware Backup appliance backups run before
or after the upgrade by using the EMC Backup and
Recovery plug-in in the vSphere Web Client
l Disaster recovery of VMware Backup appliance in case of
a VMware Backup appliance failure
l Restore to the same vCenter with a newly deployed
VMware Backup appliance by using the EMC Backup
and Recovery plug-in in the vSphere Web Client
l Recovery of VMware Backup appliance backups from a
secondary site (restore to a different vCenter) with a
newly deployed VMware Backup appliance by using the

72 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Table 10 Supported and unsupported VMware Backup appliance operations in a NetWorker 9.1
and later environment

Supported operations Unsupported operations

EMC Backup and Recovery plug-in in the vSphere

Web Client

Migration pre-requisites
When you migrate a VMware Backup appliance policy to a vProxy policy, a pre-check
occurs automatically to determine that compatibility requirements are met.
These requirements include verification of the following items:
l The Data Domain OS (DD-OS) is DDOS version 5.7, 6.0.0.30, 6.0.1-10, or 6.1. Note
that use of the DD Retention Lock feature on vProxy backup and clone actions
requires DDOS 6.1.
l The NetWorker server and storage node version is NetWorker 18.1.
l The vProxy is available on the vCenter server and is version 2.1.0.17 for NetWorker
18.1.
l The vCenter server is a minimum of version 5.5.
If this check discovers any compatibility issues that can cause problems migrating all
policies, the issues are reported and migration is cancelled. If using the command line
to migrate policies, you can specify a force flag (-f) to ignore these errors and
proceed with the migration to correct any issues afterwards, however it is
recommended that the pre-check requirements be met prior to proceeding with the
migration. Issues discovered during the pre-check will be logged and displayed even
when using the force flag.
Additionally, if you used IPv6 only or dual stack (IPv4 and IPv6) for the VMware
Backup appliance and are migrating to use the vProxy appliance, ensure that you
switch to IPv4 only. The vProxy appliance does not support either IPv6 or dual stack
(IPv4 and IPv6), and so the migration from the VMware Backup appliance to the
vProxy appliance will not work with these configurations. If you previously used IPv4
only, no configuration change is necessary.

Policy migration to vProxy by using NMC

You can use the NetWorker Management Console (NMC) Administration window to
migrate VMware Backup appliance policies and workflows to vProxy, or perform a pre-
check before migrating.
Procedure
1. In the NMC Administration window, click Protection.
2. In the left pane, expand Policies to view the VMware policy.
3. (Optional) Right-click the vmware policy and select Policy Migration >
Analyze from the drop-down if you want to perform a compatibility pre-check
before migration.
4. Right-click the vmware policy and select Policy Migration > Migrate to start
the migration.

Migration pre-requisites 73
Deploy the vProxy appliance and configure the NetWorker datazone

Figure 11 Migrating a VMware Backup appliance policy to vProxy in NMC

Note

If a pre-check failure occurs upon initiating the migration, a prompt appears to

confirm that you want to ignore the errors and proceed. It is recommended that
you resolve any pre-check errors, including unsupported software versions,
before completing the migration in order for backups to complete successfully.

Results
A Migrate Operation Results dialog box opens which provides a real-time report of
the analyzation and the migration until the process completes. You can then choose to
export a log of the analyzation or migration as a report by clicking Export Log File.
Figure 12 Migrate Operation Results dialog

Policy migration to vProxy by using the command line

You can also migrate VMware Backup appliance policies and workflows to vProxy by
using the nsrvbaupgrade command line utility, which additionally allows you to

74 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

perform a pre-migration check before migrating. The command line supports multiple
policies for each run.
Before you begin
To perform a pre-check only before migrating, run nsrvbaupgrade -c. It is
recommended that you resolve any pre-check errors, including unsupported software
versions, before completing the migration in order for backups to complete
successfully.
Procedure
1. Open a command prompt.
2. Specify the nsrvbaupgrade command in the following format:
nsrvbaupgrade –p policy [-c] [-f] [-v] where:
l -p policy specifies one or more policies to migrate
l -c runs the pre-check only
l -f forces the migration to ignore a pre-check failure
l -v specifies verbose mode

Renaming a NetWorker 9.1 and later server with legacy VMware Backup
appliance
When a NetWorker 8.2.x release is upgraded to NetWorker 9.1 and later, if you plan to
change the NetWorker server name or domain name, restore of legacy backups using
the VMware Backup appliance will fail. This occurs because when you change the
name, the NetWorker sever is in the new domain and the VMware Backup appliance is
in the old domain.
In order to ensure that the new domain can access the legacy VMware Backup
appliance backups, perform the Disaster Recovery procedures for the VMware Backup
appliance specified in the section Disaster Recovery.

Updating the Microsoft VM App Agent and FLR Agent

software
The Microsoft VM App Agent and FLR Agent software required to perform advanced
application-consistent data protection and file-level restore operations on the client
will be automatically updated on the target virtual machine by the vProxy appliance
during the file-level restore operation. The vProxy detects the available software on
the client and updates the Agent software with the new version of software from its
repository. If the update does not occur automatically, contact a Dell EMC technical
support professional for a procedure to update the vProxy software repository with
the latest version of the Agent software packages.

Updating the vProxy appliance

When you upgrade the NetWorker server to NetWorker 18.1, you must also upgrade
the vProxy appliance to the latest version for NetWorker 18.1. There is no procedure
to automatically update the vProxy appliance version. To update the vProxy appliance,

Renaming a NetWorker 9.1 and later server with legacy VMware Backup appliance 75
Deploy the vProxy appliance and configure the NetWorker datazone

you must delete the currently deployed appliance from NMC and vCenter, and then
deploy and register the new vProxy appliance on the same vCenter.
Procedure
1. Delete the vProxy appliance from NMC, as described in the section Deleting the
vProxy host.
2. Log in to the vCenter server by using the vSphere Client.
3. Remove the vProxy appliance from the vCenter by powering off the appliance
and then deleting the vProxy virtual machine from the disk.
4. Deploy the new vProxy appliance and configure the network settings, as
described in the section "Deploy the vProxy appliance".

Note

When upgrading to NetWorker 18.1 from a previous release, if the hotadd and
nbd transport modes were configured with different non-zero values for
maximum sessions, ensure that you change these settings to the same non-zero
value. Setting different non-zero values for both transport modes is not
supported in NetWorker 18.1.

5. Add the newly deployed vProxy appliance to the NetWorker server and
configure the appliance, as described in the section Configuring the vProxy in
NetWorker.
6. After vProxy appliance registration completes, verify that a valid certificate
appears in the NMC NetWorker Administration window by enabling diagnostic
mode and adding the column VM vProxy certificate.

Deleting the vProxy host

Perform the following steps to delete the resource for the vProxy appliance in
NetWorker.
Procedure
1. Log in to the NMC GUI as an administrator of the NetWorker server.
2. On the taskbar, click the Enterprise icon .
3. In the navigation tree, highlight a host:
a. Right-click NetWorker.
b. Select Launch Application. The NetWorker Administration window
appears.
4. On the taskbar, click the Devices button .
5. In the expanded left navigation pane, select VMware Proxies,
6. In the right pane, right-click on the VMware proxy, and then select Delete.
7. When prompted, click Yes to delete the VMware proxy.
After you finish
When you delete a vProxy resource after failed registration, a warning appears to
manually unregister the vProxy appliance.

76 NetWorker 18.1 VMware Integration Guide

 Deploy the vProxy appliance and configure the NetWorker datazone

Redeploying a vProxy
The procedure to redeploy a vProxy appliance requires you to perform the same steps
that you performed when you deployed the original vProxy host.
After you deploy the vProxy appliance, perform the following steps:
Procedure
1. Delete the vProxy by performing the steps in the section "Deleting the vProxy
host".
2. Deploy the vProxy by performing the procedures in the section "Deploy the
vProxy appliance".
3. Configure the vProxy using the steps in the section "Configuring the vProxy in
NetWorker".

Un-registering and re-registering a vProxy after removal

When registration fails for a vProxy appliance that was previously registered to a
NetWorker server but was removed due to a disaster recovery, or because the
previous removal did not complete successfully, you must un-register the vProxy
appliance manually before you can re-register the appliance.
Procedure
1. Start the nsradmin utility.
2. In Visual mode, select the NSR VMWare proxy resource.
3. In the Options menu, select the Hidden item view.
4. Press the ESC key to return to the NSR VMWare proxy resource view, and then
select Edit from the Options menu.
5. Navigate to operation property and select Unregister.
6. Press the ESC key and then confirm that you want to save the changes to the
resource.
7. Select Edit from the Options menu and repeat step 5, only this time selecting
Register.
8. Press the ESC key and then confirm that you want to save the changes to the
resource.
Results
The vProxy registration starts. You can now exit the nsradmin utility.

Resetting the admin account password

The vProxy appliance locks the admin account when you try to log in to the appliance
with an incorrect password three consecutive times.
Perform the following steps to unlock the admin account and reset the password.
Procedure
1. From the vSphere Client application, open a console window on the vProxy
appliance or use ssh to connect to the appliance from a host that has network
access to the vProxy appliance.

Redeploying a vProxy 77
Deploy the vProxy appliance and configure the NetWorker datazone

2. Log in to the appliance with the root account.

The default password for the root account is changeme.
3. Use the pam_tally2 command to unlock the admin account.
For example:

pam_tally2 --user admin --reset

Output similar to the following appears:

Login Failures Latest failure From
admin 5 04/22/13 21:22:37 123.456.789

4. Use the passwd command to reset the admin password

For example:

passwd admin

The pam_tally2 man page provides more information about the pam_tally2
command and how to configure the maximum number of login attempts for a user
account.

78 NetWorker 18.1 VMware Integration Guide

CHAPTER 3
Protecting virtual machines

This chapter contains the following topics:

l Preparing the NetWorker data zone...................................................................80

l Creating VMware data protection policies in NMC for the vProxy appliance...... 81
l vProxy backup workflows in the vSphere Client's Dell EMC NetWorker interface
.......................................................................................................................... 112
l vProxy workflows in the vSphere Web Client's VM Backup and Recovery
interface............................................................................................................118
l Troubleshooting Data Protection Policies......................................................... 122

Protecting virtual machines 79

Protecting virtual machines

Preparing the NetWorker data zone

Review the following requirements.
l Before you configure backup and clone operations, create a DD Boost device and
configure the Data Domain management host in NetWorker.
l Before you use file-level restore and instant access restore, enable NFS on the
Data Domain System.

Configure the Data Domain System

The Data Domain system must be configured with DD Boost and NFS before
configuring vProxy policies.
Procedure
1. Use a web browser to log in to the Data Domain System Manager as the
system administrator user.
2. In the left navigation pane, select Protocols > DD Boost.
3. On the Settings tab that is located near the top of the page, perform the
following tasks:
a. Ensure that the DD Boost Status is Enabled.
b. If it does not appear, add the appliance to the Allowed Clients table:
a. Click the + (Add) button that is located above the table and to the right.
b. In the Client field, specify the fully qualified domain name (FQDN) of the
host.
c. In the Authentication mode list, select None.
d. In the Encryption Strength list, select None.
e. Click OK.

Note

By default, all clients (*) are allowed to access DD Boost.

c. If it does not exist, add the DD Boost user to the Users with DD Boost
Access table:
a. Click the + (Add) button that is located above the table and to the right.
b. In the User list, select an existing local user, or select Create a new
Local User and then create a user account.
c. Click Add, and then click Close.

4. For file-level restore and instant access restore only, on Protocols, select NFS,
ensure that NFS status is enabled, and then click OK.
The vProxy appliance dynamically creates and deletes the NFS shares, as
required.

80 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Creating VMware data protection policies in NMC for the

vProxy appliance
You can use the NMC NetWorker Administration window to create VMware
protection policies for the vProxy appliance, and then schedule backups of these
policies.
Setting up and configuring data protection policies for the vProxy appliance in
NetWorker involves the following tasks:
l Creating a policy.
l Creating a workflow.
l Creating a VMware protection group.
l Creating an action.

Overview of data protection policies

Data protection policy is a concept that provides you with the ability to design a data
protection solution for the environment at the data level instead of at the host level.
With a data protection policy, each client in the environment is a backup object and
not simply a host.
Data protection policies enable you to back up and manage data in a variety of
environments, as well as to perform system maintenance tasks on the NetWorker
server.
A data protection policy solution encompasses the configuration of the following key
NetWorker resources:
Policies
Policies provide you with the ability to develop a service-catalog approach to the
configuration of a NetWorker datazone. Policies enable you to manage all data
protection tasks and the data protection lifecycle from a central location.
Policies provide an organizational container for the workflows, actions, and groups
that support and define the backup, clone, management, and system maintenance
actions that you want to perform.
Workflows
Workflows define the start time for a series of actions, the frequency in which the
actions run, the order of actions in a sequence, and the protection group to which the
workflow applies.
A workflow can be as simple as a single action that applies to a finite list of Client
resources, or a complex chain of actions that apply to a dynamically changing list of
resources. In a workflow, some actions can be set to occur sequentially, and others
can occur concurrently.
You can create multiple workflows in a single policy. However, each workflow can
belong to only one policy. When you add multiple workflows to the same policy, you
can logically group data protection activities with similar service level provisions
together, to provide easier configuration, access, and task execution.
Protection groups
Protection groups define a set of static or dynamic Client resources or save sets to
which a workflow applies. There are also dedicated protection groups for backups in a
VMware environment or for snapshot backups on a NAS device. Review the following
information about protection groups:

Creating VMware data protection policies in NMC for the vProxy appliance 81
Protecting virtual machines

l Create one protection group for each workflow. Each group can be assigned to
only one workflow.
l You can add the same Client resources and save sets to more than one group at a
time.
l You can create the group before you create the workflow, or you can create the
group after you create the workflow and then assign the group to the workflow
later.
Actions
Actions are the key resources in a workflow for a data protection policy and define a
specific task, for example, a backup, clone, or snapshot. NetWorker uses a work list to
define the task. A work list is composed of one or several work items. Work items
include client resources, virtual machines, save sets, or tags. You can chain multiple
actions together to occur sequentially or concurrently in a workflow. All chained
actions use the same work list.
When you configure an action, you define the days on which to perform the action, as
well as other settings specific to the action. For example, you can specify a destination
pool, a retention period, and a target storage node for the backup action, which can
differ from the subsequent action that clones the data.
You can create multiple actions for a single workflow. However, each action applies to
a single workflow and policy.
The following figure provides a high level overview of the components that make up a
data protection policy in a datazone.
Figure 13 Data Protection Policy

Default data protection policies

NetWorker provides you with preconfigured data protection policies that you can use
immediately to protect the environment, modify to suit the environment, or use an
example to create resources and configurations. To use these preconfigured data
protection policies, you must add clients to the appropriate group resource.

Note

NetWorker also includes a preconfigured Server Protection policy to protect the

NetWorker and NMC server databases.

Platinum policy
The Platinum policy provides an example of a data protection policy for an
environment that contains supported storage arrays or storage appliances and
requires backup data redundancy. The policy contains one workflow with two actions,
a snapshot backup action, followed by a clone action.

82 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Figure 14 Platinum policy configuration

Gold policy
The Gold policy provides an example of a data protection policy for an environment
that contains virtual machines and requires backup data redundancy.
Silver policy
The Silver policy provides an example of a data protection policy for an environment
that contains machines where file systems or applications are running and requires
backup data redundancy.
Bronze policy
The Bronze policy provides an example of a data protection policy for an environment
that contains machines where file systems or applications are running.

Create a VMware policy

If you do not want to use the default "Gold" policy for the protection of virtual
machines, you can create a new VMware policy by using the following procedure.
Procedure
1. On the Administration window, click Protection.
2. In the expanded left pane, right-click Policies, and then select New.
The Create Policy dialog box appears.
3. On the General tab, in the Name field type a name for the policy.
The maximum number of characters for the policy name is 128.

Note

This name cannot contain spaces or special characters such as + or %. After

you create a policy, the Name attribute is read-only.

4. In the Comment box, type a description for the policy.

5. From the Send Notifications list, select whether to send notifications for the
policy:
l To avoid sending notifications, select Never.
l To send notifications with information about each successful and failed
workflow and action after all the actions in the policy complete, select On
Completion.
l To send a notification with information about each failed workflow and
action after all the actions in the policy complete, select On Failure.
6. In the Send notification attribute, when you select the On Completion option
or On failure option, the Command box appears. Use this box to configure how
NetWorker sends the notifications. You can use the nsrlog command to send
the notifications to a log file or you can send an email notification.
The default notification action is to send the information to the
policy_notifications.log file. By default, the

Create a VMware policy 83

Protecting virtual machines

policy_notifications.log file is located in the /nsr/logs directory on

Linux and in the C:\Program Files\EMC NetWorker\nsr\logs folder on
Windows.
Use the default mailer program on Linux to send email messages or the
smtpmail application on Windows:
l To send notifications to a file, type the following command, where
policy_notifications.log is the name of the file:

nsrlog -f policy_notifications.log
l On Linux, to send an email notification, type the following command:

mail -s subject recipient

l For NetWorker Virtual Edition (NVE), to send an email notification, type the
following command:

/usr/sbin/sendmail -v recipient_email "subject_text"

l On Windows, to send a notification email, type the following command:

smtpmail -s subject -h mailserver recipient1@mailserver

recipient2@mailserver...

where:
n -s subject—Includes a standard email header with the message and
specifies the subject text for that header. Without this option, the
smtpmail program assumes that the message contains a correctly
formatted email header and nothing is added.
n -h mailserver—Specifies the hostname of the mail server to use to
relay the SMTP email message.
n recipient1@mailserver—Is the email address of the recipient of the
notification. Multiple email recipients are separated by a space.

7. In the Restricted Data Zones tab, leave the Restricted Data Zone field blank.
NetWorker VMware Protection with the vProxy appliance does not currently
support the protection of virtual machines within a Restricted Data Zone.
8. Click OK.
After you finish
You can now create the workflow, group, and actions for the policy.

Creating a workflow
The policy workflow defines a list of actions to perform sequentially or concurrently, a
schedule window during which the workflow can run, and the client resource or save
set group to which the workflow applies. You can create a workflow when you create a
new policy, or you can create a workflow for an existing policy.

Create a workflow in a new policy

Procedure
1. In the Administration window, click Protection.
2. In the left pane, expand Policies, and then select the policy that you created.
3. In the right pane, select Create a new workflow.

84 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

4. In the Name field, type the name of the workflow.

The maximum number of allowed characters for the Name field is 64. This name
cannot contain spaces or special characters such as + or %.
5. In the Comment box, type a description for the workflow.
The maximum number of allowed characters for the Comment field is 128.
6. From the Send Notifications list, select how to send notifications for the
workflow:
l To use the notification configuration that is defined in the policy resource to
specify when to send a notification, select Set at policy level.
l To send notifications with information about each successful and failed
workflow and action, after the workflow completes all the actions, select On
Completion.
l To send notifications with information about each failed workflow and
action, after the workflow completes all the actions, select On Failure.
7. In the Send notification attribute, when you select the On Completion option
or On failure option, the Command box appears. Use this box to configure how
NetWorker sends the notifications. You can use the nsrlog command to send
the notifications to a log file or you can send an email notification.
The default notification action is to send the information to the
policy_notifications.log file. By default, the
policy_notifications.log file is located in the /nsr/logs directory on
Linux and in the C:\Program Files\EMC NetWorker\nsr\logs folder on
Windows.
Use the default mailer program on Linux to send email messages, or use the
smtpmail application on Windows:
l To send notifications to a file, type the following command, where
policy_notifications.log is the name of the file:

nsrlog -f policy_notifications.log
l On Linux, to send an email notification, type the following command:

mail -s subject recipient

l For NetWorker Virtual Edition (NVE), to send an email notification, type the
following command:

/usr/sbin/sendmail -v recipient_email "subject_text"

l On Windows, type the following command:
smtpmail -s subject -h mailserver recipient1@mailserver
recipient2@mailserver...

where:
n -s subject—Includes a standard email header with the message and
specifies the subject text for that header. Without this option, the
smtpmail program assumes that the message contains a correctly
formatted email header and nothing is added.
n -h mailserver—Specifies the hostname of the mail server to use to
relay the SMTP email message.
n recipient1@mailserver—Is the email address of the recipient of the
notification. Multiple email recipients are separated by a space.

Creating a workflow 85
Protecting virtual machines

8. In the Running section, perform the following steps to specify when and how
often the workflow runs:
a. To ensure that the actions that are contained in the workflow run when the
policy or workflow starts, in the Enabled box, leave the option selected. To
prevent the actions in the workflow from running when the policy or
workflow that contains the action starts, clear this option.
b. To start the workflow at the time that is specified in the Start time
attribute, on the days that are defined in the action resource, in the
AutoStart Enabled box, leave the option selected. To prevent the workflow
from starting at the time that is specified in the Start time attribute, clear
this option.
c. To specify the time to start the actions in the workflow, in the Start Time
attribute, use the spin boxes.
The default value is 9:00 PM.

d. To specify how frequently to run the actions that are defined in the
workflow over a 24-hour period, use the Interval attribute spin boxes. If you
are performing transaction log backup as part of application-consistent
protection, you must specify a value for this attribute in order for
incremental transaction log backup of SQL databases to occur.
The default Interval attribute value is 24 hours, or once a day. When you
select a value that is less than 24 hours, the Interval End attribute appears.
To specify the last start time in a defined interval period, use the spin boxes.

e. To specify the duration of time in which NetWorker can manually or

automatically restart a failed or canceled workflow, in the Restart Window
attribute, use the spin boxes.
If the restart window has elapsed, NetWorker considers the restart as a new
run of the workflow. NetWorker calculates the restart window from the start
of the last incomplete workflow. The default value is 24 hours.
For example, if the Start Time is 7:00 PM, the Interval is 1 hour, and the
Interval End is 11:00 PM., then the workflow automatically starts every hour
beginning at 7:00 PM. and the last start time is 11:00 PM.

9. To create the workflow, click OK.

After you finish
Create the actions that will occur in the workflow, and then assign a group to the
workflow. If a workflow does not contain a group, a policy does not perform any
actions.

Create a workflow in an existing policy

A policy can contain one or more unique workflows.
Before you begin
l Create a policy for the workflow.
l (Optional but recommended) Create a group of client resources or save sets to
assign to the workflow.
Procedure
1. In the Administration window, click Protection.

86 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

2. In the expanded left pane, select Policies.

3. Select the policy for the workflow.
4. In the right pane of the window, select the Workflows tab.
5. Right-click an empty area of the Workflows tab and select New.
The New Workflow dialog box appears.
6. In the Name field, type the name of the workflow.
The maximum number of allowed characters for the Name field is 64. This name
cannot contain spaces or special characters such as + or %.
7. In the Comment box, type a description for the workflow.
The maximum number of allowed characters for the Comment field is 128.
8. From the Send Notifications list, select how to send notifications for the
workflow:
l To use the notification configuration that is defined in the policy resource to
specify when to send a notification, select Set at policy level.
l To send notifications with information about each successful and failed
workflow and action, after the workflow completes all the actions, select On
Completion.
l To send notifications with information about each failed workflow and
action, after the workflow completes all the actions, select On Failure.
9. In the Send notification attribute, when you select the On Completion option
or On failure option, the Command box appears. Use this box to configure how
NetWorker sends the notifications. You can use the nsrlog command to send
the notifications to a log file or you can send an email notification.
The default notification action is to send the information to the
policy_notifications.log file. By default, the
policy_notifications.log file is located in the /nsr/logs directory on
Linux and in the C:\Program Files\EMC NetWorker\nsr\logs folder on
Windows.
Use the default mailer program on Linux to send email messages or the
smtpmail application on Windows:
l To send notifications to a file, type the following command, where
policy_notifications.log is the name of the file:

nsrlog -f policy_notifications.log
l On Linux, to send an email notification, type the following command:

mail -s subject recipient

l On Windows, type the following command: smtpmail -s subject -h
mailserver recipient1@mailserver recipient2@mailserver...
where:
n -s subject—Includes a standard email header with the message and
specifies the subject text for that header. Without this option, the
smtpmail program assumes that the message contains a correctly
formatted email header and nothing is added.
n -h mailserver—Specifies the hostname of the mail server to use to
relay the SMTP email message.

Creating a workflow 87
Protecting virtual machines

n recipient1@mailserver—Is the email address of the recipient of the

notification. Multiple email recipients are separated by a space.

10. In the Running section, perform the following steps to specify when and how
often the workflow runs:
a. To ensure that the actions that are contained in the workflow run when the
policy or workflow starts, in the Enabled box, leave the option selected. To
prevent the actions in the workflow from running when the policy or
workflow that contains the action starts, clear this option.
b. To start the workflow at the time that is specified in the Start time
attribute, on the days that are defined in the action resource, in the
AutoStart Enabled box, leave the option selected. To prevent the workflow
from starting at the time that is specified in the Start time attribute, clear
this option.
c. To specify the time to start the actions in the workflow, in the Start Time
attribute, use the spin boxes.
The default value is 9:00 PM.

d. To specify how frequently to run the actions that are defined in the
workflow over a 24-hour period, use the Interval attribute spin boxes. If you
are performing transaction log backup as part of application-consistent
protection, you must specify a value for this attribute in order for
incremental transaction log backup of SQL databases to occur.
The default Interval attribute value is 24 hours, or once a day. When you
select a value that is less than 24 hours, the Interval End attribute appears.
To specify the last start time in a defined interval period, use the spin boxes.

e. To specify the duration of time in which NetWorker can manually or

automatically restart a failed or canceled workflow, in the Restart Window
attribute, use the spin boxes.
If the restart window has elapsed, NetWorker considers the restart as a new
run of the workflow. NetWorker calculates the restart window from the start
of the last incomplete workflow. The default value is 24 hours.
For example, if the Start Time is 7:00 PM, the Interval is 1 hour, and the
Interval End is 11:00 PM., then the workflow automatically starts every hour
beginning at 7:00 PM. and the last start time is 11:00 PM.

11. In the Groups group box, specify the protection group to which the workflow
applies.
To use a group, select a protection group from the Groups list. To create a
protection group, click the + button that is located to the right of the Groups
list.
12. The Actions table displays a list of actions in the workflow. To edit or delete an
action in the workflow, select the action and click Edit or Delete. To create one
or more actions for the workflow, click Add.
The Actions table organizes the information in sortable columns. Right-click in
the table to customize the attributes that appear.
13. To create the workflow, click OK.

88 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Create or edit a VMware group

A VMware group allows you to define the virtual machines or virtual disk files to back
up within the policy/workflow.
Before you begin
Ensure that you perform the steps in the section Adding the vCenter host to VMware
View and creating the vCenter client resource, and confirm that the map appears.
Procedure
1. In the Administration window, click Protection.
2. In the expanded left pane, right-click Groups and select New from the drop-
down, or right-click an existing group and select Edit from the drop-down.
The Create Group or Edit Group dialog box appears, with the General tab
selected.
3. In the Name attribute, type a name for the group.
The maximum number of characters for the group name is 64. This name cannot
contain spaces or special characters such as + or %.

Note

After you create a group, the Name attribute is read-only.

4. From the Group Type list, select VMware.

5. From the Sub-Type list, select ALL.
NetWorker does not support other sub-types in this configuration.
6. From the Optimization drop-down, select a backup optimization mode.
Capacity is for variable segment sizing, while Performance is for fixed segment
sizing.
7. In the Comment field, type a description of the group.
8. From the Policy-Workflow list, select the workflow that you want to assign the
group to.

Note

You can also assign the group to a workflow when you create or edit a
workflow.

9. (Optional) Select the Dynamic Association checkbox if you plan to apply rules
that will determine which virtual machines and containers are dynamically
included in the group based upon the rule criteria. The section xxx provides
more information on enabling a policy/group with Dynamic Association and
applying rules.
10. From the vCenter drop-down, select the vCenter server that contains the
VMware objects that you want to protect, and then select the objects
(Datacenter, ESX host, virtual machine, resource pool, vApp, or disk) to include
in this group. Any objects selected here will be considered static objects, which
means that the items will be included in the group until unselected, even when
Dynamic Association is enabled.

Create or edit a VMware group 89

Protecting virtual machines

Note

If the vCenter list is empty, cancel the task and, using the NMC Protection
window, right-click VMware View in the left pane, and select Refresh.

11. (Optional) If the group as Dynamic Association enabled, from the Rule drop-
down, select a pre-defined rule that you want to apply for any VMware objects
that will be dynamically included in the group based upon the rule criteria, or
click + to open the Create Rule window and create a new rule. The section xxx
provides more information on associating a VMware group with rules.
12. Click Preview All Virtual Machines to view a list of the static and dynamic
virtual machines and objects that have been added to the group. In this window,
you can also unselect a virtual machine or VMDK to exclude the item from the
backup. When an object is unselected, an entry for the object appears in the
Excluded VM list.
13. Click OK to exit the Preview Virtual Machines window, and then click OK to
finish creating or editing the group.

vProxy backup optimization modes

NetWorker supports two types of backup optimization modes for vProxy backup to
Data Domain systems—Optimized for Capacity, and Optimized for Performance.
You can apply the optimization mode to vProxy protection groups during backup.
The Optimized for Capacity mode uses variable size segmentation, which produces
more overhead in data processing due to the higher deduplication rate, but reduces
the capacity consumed on the Data Domain system. Virtual machines backed up prior
to NetWorker 9.1 use the Optimized for Capacity mode.
Optimized for Performance provides performance improvements when you back up
virtual machines using Changed Block Tracking (CBT) and replicate data to a Data
Domain system, and is particularly effective when backing up large VMDK files.
Although Optimized for Performance results in additional space use on the Data
Domain device (around 20%), this mode significantly improves random I/O
performance for instant access restores.
New and upgraded installations of NetWorker use the Optimized for Capacity mode
by default. For a vProxy protection group, you can change this setting to Optimized
for Performance by using NMC, nsradmin, or nsrpolicy. The following figure
displays the backup optimization setting within a vProxy protection group in NMC.

90 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Figure 15 Changing the Backup Optimization mode in the vProxy protection group

Software and storage requirements for Optimized for Performance mode

Using Optimized for Performance requires DDOS version 5.7.x or version 6.0.0.30
and later. If using a DDOS 5.7 version, DDOS 5.7.1 or later is recommended for this
mode. When you request Optimized for Performance mode but it is not supported by
the DDOS version, the backup automatically falls back to using Optimized for
Capacity. A warning log message will be generated. Also, cloning of Optimized for
Performance save sets is supported only between DDOS platforms that natively
support this mode (DDOS version 5.7 and later).
Requirements when changing backup optimization modes
Changing a virtual machine from one backup optimization mode to another (for
example, from Optimized for Capacity to Optimized for Performance) requires
performing a new full level-zero backup as the starting point for subsequent backups.
Ensure that the Data Domain device has sufficient capacity. Since backups for each
optimization mode must coexist during this period, backups will consume twice the
usual storage capacity until the last Optimized for Capacity backup expires, as
defined by the retention period. After this, storage consumption will return to normal.

VMware actions
Actions are the key resources in a workflow for a data protection policy. An action is
the task that occurs on the client resources in the group assigned to the workflow.
You can chain multiple actions together to occur sequentially or concurrently in a
workflow.
When you create an action for a policy that is associated with the virtual machine
backup, you can select one of the following data protection action types:
l Backup (Backup Subtype—VMware (vProxy))—Performs a backup of virtual
machines in vCenter to a Data Domain system. You can only perform one VMware

VMware actions 91
Protecting virtual machines

backup action per workflow. The VMware backup action must occur before clone
actions.
l Clone—Performs a clone of the VMware backup on a Data Domain system to any
clone device that NetWorker supports (including Data Domain system or tape
targets). You can specify multiple clone actions. Clone actions must occur after
the Backup action.

Creating a VMware backup action

A VMware backup is a scheduled backup of virtual machines within a vCenter. The
following section provides details for creating a VMware backup action for vProxy.
The NetWorker Administration Guide provides information about other action types.
Before you begin
Create the policy and workflow that contain the action.
Procedure
1. In the expanded left pane, select the policy's workflow, and then perform one of
the following tasks in the right pane to start the Policy Action wizard:
l If the action is the first action in the workflow, select Create a new action.
l If the workflow has other actions, right-click an empty area of the Actions
pane, and then select New.
The Policy Action wizard opens on the Specify the Action Information page.
2. In the Name field, type the name of the action.
The maximum number of characters for the action name is 64.
3. In the Comment field, type a description for the action.
4. To ensure that the action runs when the policy or workflow that contains the
action is started, in the Enabled box, select the option. To prevent the action
from running when the policy or workflow that contains the action is started,
clear this option.

Note

When you clear the Enabled option, actions that occurs after a disabled action
do not start, even if the subsequent options are enabled.

5. From the Action Type list, select Backup.

6. From the secondary action list, select VMware (vProxy).
7. If you create the action as part of the workflow configuration, the workflow
appears automatically in the Workflow box and the box is dimmed.
8. Specify the order of the action in relation to other actions in the workflow:
l If the action is part of a sequence of actions in a workflow path, in the
Previous box, select the action that should precede this action.
l If the action should run concurrently with an action, in the Previous box,
select the concurrent action, and then select the Concurrent checkbox.
9. Specify a weekly or monthly schedule for the action:
l To specify a schedule for each day of the week, select Weekly by day.
l To specify a schedule for each day of the month, select Monthly by day.
10. Click the icon on each day to specify the backup level to perform.

92 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Backup levels for NetWorker VMware Protection include the following.

Note

Any backup level that displays in the wizard but is not identified in this table is
not supported for VMware.

Table 11 Schedule icons

Icon Label Description

Full Perform a full backup on this
day. Full backups include all
files, regardless of whether
the files changed. In the case
of virtual machine backup,
this is a virtual machine disk
(VMDK) backup to Data
Domain.

Incr Uses the previous backup and

leverages changed block
tracking to write only
incremental blocks to a new
backup that is independent of
other backups.

Note

Since the backup is

performed to Data Domain,
the resulting backup on the
target device is a new full
backup because NetWorker
uses Data Domain virtual
synthetics technology to
create a synthetic full backup.

Skip Do not perform a backup on

this day.

To perform the same type of backup on each day, select the backup type from
the list and click Make All.

Note

A full backup is required initially if performing application-consistent backup of

virtual machines as part of this action.

11. Click Next.

The Specify vProxy Options page appears.

VMware actions 93
Protecting virtual machines

Figure 16 Specify vProxy Options page

12. From the Destination Storage Node box, select the storage node that contains
the devices where you want to store the backup data.

Note

When you deploy the vCenter server in the Cloud, a parameter displays in the
backup action logs that indicates HypervisorMode: VMC. When not deployed
in the Cloud, the parameter indicates HypervisorMode: vSphere.
13. From the Retention spin boxes, specify the amount of time to retain the
backup data.
After the retention period expires, the save set is removed from the client file
index and marked as recyclable in the media database during an expiration
server maintenance task.

14. Select the Apply DD Retention Lock checkbox to enable retention lock for the
virtual machines included in this backup action. Note that the device used for
backing up these virtual machines must also have DD Retention lock enabled in
the NMC Device Properties window, or DD Retention Lock must be enabled
during device creation.
15. In the DD Retention Lock Time box, specify the duration the virtual machines
will remain on the Data Domain device before the retention lock expires. During
this time, these virtual machine backups cannot be overwritten, modified, or
deleted for the duration of the retention period, although the backups can be
mounted and unmounted. The retention time period set here must fall within the
minimum and maximum values set for the Data Domain Mtree, and should be
lower than or equal to the NetWorker Retention Period.

94 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

16. In the vProxy section, select one of the following options:

l Auto vProxy Selection—Select this option to allow NetWorker to choose
the vProxy host for backups.
l Manual vProxy Selection—Specify this option to define the vProxy host
that NetWorker users for backups. Provide the name of the vProxy host in
the vProxy Name field.
17. From the Destination Pool box, select the media pool in which to store the
backup data.
Only pools configured with a DDBoost device appear in the drop-down.
18. In the Application Consistency section, select the Quiesce Application
checkbox to enable application-consistent protection as part of the policy
backup action, which includes protection of the Microsoft SQL Server. You can
then select from the Basic and Advanced options.
l Select the Basic option to create a backup copy for applications during
virtual machine quiescing. No additional processing is performed.
l Select the Advanced option to create an SQL server application-consistent
backup during virtual machine quiescing, and optionally create a transaction
log backup for all SQL Server instances.
When you select the option, the following fields display:
l Transaction Log Backup—Select this checkbox if you want to perform a
transaction log backup of SQL databases in the virtual machine as part of
the policy backup action. Note that if you enable transaction log backup, you
must also set a value for the Interval attribute in the Workflow properties
for this action, as specified in the section "Creating a workflow in a new
policy."

Note

During SQL Server configuration, the NT AUTHORITY\SYSTEM login must

be granted SQL login and SQL sysadmin role rights in order to perform
transaction log backups.
l Quiesce Timeout—Specify the amount of time, in minutes, to wait for the
quiesce operation on the virtual machine to time out before failing. If not
selected, the backup action will proceed even if quiescing was not
performed, unless a validation problem occurs. If an application-consistent
backup cannot complete due to a problem with validation, the backup action
will fail even if this checkbox is not selected.
l System Administrator Username and Password—Specify the virtual
machine credentials for a user with administrative privileges. All virtual
machines in the workflow should use the same System Administrator
username/password.

VMware actions 95
Protecting virtual machines

Note

Selecting the Advanced option will apply application-consistent processing for

all virtual machines within the parent workflow. When selecting this option,
ensure that the policy's workflow and client groups are provisioned specifically
for virtual machines that require advanced application-consistent protection.
NetWorker will always attempt to perform advanced application processing for
virtual machines in a workflow that contains a backup action with advanced
application processing enabled. The section Creating an action for application-
consistent data protection provides more information.

19. Click Next.

The Specify the Advanced Options page appears.
20. Although the Retries, Retry Delay, and the Inactivity Timeout options appear,
this action does not support these options and you can ignore these values.
21. In the Parallelism field, specify the maximum number of concurrent operations
for the action.
22. From the Soft Limit list, select the amount of time after the action starts to
stop the initiation of new activities. The default value of 0 (zero) indicates no
amount of time.
23. From the Hard Limit list, select the amount of time after the action starts to
begin terminating activities. The default value of 0 (zero) indicates no amount
of time.
24. (Optional) Configure overrides for the task that is scheduled on a specific day.
To specify the month, use the navigation buttons and the month list box. To
specify the year, use the spin boxes. You can set an override in the following
ways:
l Select the day in the calendar, which changes the action task for the
specific day.
l Use the action task list to select the task, and then perform one of the
following steps:
n To define an override that occurs on a specific day of the week, every
week, select Specified day, and then use the lists. Click Add Rules
based override.
n To define an override that occurs on the last day of the calendar month,
select Last day of the month. Click Add Rules based override.

Note

n You can edit or add the rules in the Override field.

n To remove an override, delete the entry from the Override field.

25. From the Send Notifications list box, select whether to send notifications for
the action:
l To use the notification configuration that is defined in the Policy resource to
send the notification, select Set at policy level.
l To send a notification on completion of the action, select On Completion.
l To send a notification only if the action fails to complete, select On Failure.

96 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

26. Click Next.

The Action Configuration Summary page appears.
27. Review the settings that you specified for the action, and then click Configure.
After you finish
(Optional) Create a clone action to automatically clone the save sets after the backup.
A clone action is the only supported action after a backup action in a workflow.

Creating a clone action

A clone action creates a copy of one or more save sets. Cloning allows for secure
offsite storage, the transfer of data from one location to another, and the verification
of backups.
Procedure
1. In the expanded left pane, select the policy's workflow, and then perform one of
the following tasks in the right pane to start the Policy Action wizard:
l If the action is the first action in the workflow, select Create a new action.
l If the workflow has other actions, right-click an empty area of the Actions
pane, and then select New.
The Policy Action wizard opens on the Specify the Action Information page.
2. In the Name field, type the name of the action.
The maximum number of characters for the action name is 64.
3. In the Comment field, type a description for the action.
4. To ensure that the action runs when the policy or workflow that contains the
action is started, in the Enabled box, select the option. To prevent the action
from running when the policy or workflow that contains the action is started,
clear this option.

Note

When you clear the Enabled option, actions that occurs after a disabled action
do not start, even if the subsequent options are enabled.

5. From the Action Type list, select Clone.

6. If you create the action as part of the workflow configuration, the workflow
appears automatically in the Workflow box and the box is dimmed.
7. Specify the order of the action in relation to other actions in the workflow:
l If the action is part of a sequence of actions in a workflow path, in the
Previous box, select the action that should precede this action.
l If the action should run concurrently with an action, in the Previous box,
select the concurrent action, and then select the Concurrent checkbox.
8. Specify a weekly or monthly schedule for the action:
l To specify a schedule for each day of the week, select Weekly by day.
l To specify a schedule for each day of the month, select Monthly by day.
9. Specify the days to perform cloning:
l To clone on a specific day, click the Execute icon on the day.

VMware actions 97
Protecting virtual machines

l To skip a clone on a specific day, click the Skip icon on the day.
l To check connectivity every day, select Execute from the list, and then click
Make All.
The following table provides details on the icons.

Table 12 Schedule icons

Icon Label Description

Execute Perform cloning on this day.

Skip Do not perform cloning on

this day.

10. Click Next.

The Specify the Clone Options page appears.
11. In the Data Movement group box, define the volumes and devices to which
NetWorker sends the clone data.
a. From the Destination Storage Node list, select the storage node with the
devices on which to store the cloned save sets.
b. In the Delete source save sets after clone completes, select the option to
instruct NetWorker to remove the source save set information from the
client file index, and to mark the save set as recyclable in the media database
during a Server expiration maintenance action. Clear this option to allow the
source save sets to expire based on the defined retention time.
c. From the Destination Pool list, select the target media pool for the cloned
save sets.
d. From the Retention list, specify the amount of time to retain the cloned
save sets. After the retention period expires, the save sets are marked as
recyclable during an expiration server maintenance task.
12. Click Next.
The Specify the Advanced Options page appears.
13. Configure advanced options, including notifications and schedule overrides.

Note

Although the Retries, Retry Delay, or the Inactivity Timeout options appear,
the clone action does not support these options and ignores the values.

14. In the Parallelism field, specify the maximum number of concurrent operations
for the action. This value should not exceed 25.
15. From the Failure Impact list, specify what to do when a job fails:
l To continue the workflow when there are job failures, select Continue.
l To abort the entire workflow if there is a failure with one of the jobs in the
action, select Abort workflow.

98 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Note

If any of the actions fail in the workflow, the workflow status does not appear
as interrupted or cancelled. NetWorker reports the workflow status as failed.

16. From the Send Notifications list box, select whether to send notifications for
the action:
l To use the notification configuration that is defined in the Policy resource to
send the notification, select Set at policy level.
l To send a notification on completion of the action, select On Completion.
l To send a notification only if the action fails to complete, select On Failure.

17. From the Soft Limit list, select the amount of time after the action starts to
stop the initiation of new activities. The default value of 0 (zero) indicates no
amount of time.
18. From the Hard Limit list, select the amount of time after the action starts to
begin terminating activities. The default value of 0 (zero) indicates no amount
of time.
19. Optional, in Start Time specify the time to start the action.
Use the spin boxes to set the hour and minute values, and select one of the
following options from the drop-down list:
l Disabled—Do not enforce an action start time. The action will start at the
time defined by the workflow.
l Absolute—Start the action at the time specified by the values in the spin
boxes.
l Relative—Start the action after the period of time defined in the spin boxes
has elapsed after the start of the workflow.

20. (Optional) Configure overrides for the task that is scheduled on a specific day.
To specify the month, use the navigation buttons and the month list box. To
specify the year, use the spin boxes. You can set an override in the following
ways:
l Select the day in the calendar, which changes the action task for the
specific day.
l Use the action task list to select the task, and then perform one of the
following steps:
n To define an override that occurs on a specific day of the week, every
week, select Specified day, and then use the lists. Click Add Rules
based override.
n To define an override that occurs on the last day of the calendar month,
select Last day of the month. Click Add Rules based override.

Note

n You can edit or add the rules in the Override field.

n To remove an override, delete the entry from the Override field.

21. Click Next.

VMware actions 99
Protecting virtual machines

The Action Configuration Summary page appears.

22. Review the settings that you specified for the action, and then click Configure.
After you finish
(Optional) Create a clone action to automatically clone the save sets again after this
clone action. Another clone action is the only supported action after a clone action in a
workflow.

Creating an action for Microsoft SQL Server application-consistent protection

You can create a backup action with SQL Server application-consistent protection of
virtual machines by using the Policy Action wizard in NMC. When you enable a
VMware backup action with this feature, you can run full backups of SQL databases as
part of the VMware image-level backup, and also perform incremental backups of the
transaction log.
SQL Server application-consistent protection is enabled in the Specify the vProxy
and Application Protection Options page of the Policy Action wizard by selecting
the Application Protection checkbox and then selecting an Application Protection
Type, as outlined in the steps for Create a VMware backup action.
SQL Server application-consistent protection enables the following backup
operations:
l SQL Server backup—Select this option in the Policy Action wizard in NMC to
perform image-level (FULL) backup with application-consistent processing. This
backup will request VMware Tools to perform a FULL quiesce type for applications
running in the virtual machine in order to provide a full backup of the Microsoft
SQL Server instances within the virtual machine. Upon completion of the virtual
machine image snapshot, the Microsoft VM App Agent is called to catalog this
backup, writing the catalog to the Data Domain system.
l Transaction log backup—Select this option in the Policy Action wizard in NMC to
perform transaction log backups of SQL Server databases for all SQL Server
Instances in the virtual machine. Note that if you perform transaction log backup,
you must also set the Interval attribute in the policy's Workflow Properties
window in NMC. The transaction log backup of SQL databases is separate from
the virtual machine image-level backup, as no virtual machine image-level backup
occurs during the transaction log backup. Transaction log backup files will be
saved to the backup folder for the current save set on the Data Domain system.
Databases that do not support transaction log backup are filtered out.
The process for creating a policy with SQL Server application-consistent protection of
virtual machines in NMC is very similar to creating a policy with the VMware backup
action, with the following exceptions:
l You must provision a new policy and workflow exclusively for SQL clients that
require SQL Server application-consistent protection.
l You must provision a new policy and workflow exclusively for SQL clients that
have different security accounts, for example, system administrator username
and/or password.
l It is recommended that the virtual machines included in the group for the
dedicated workflows are not contained within multiple workflows.
Creating a workflow with an SQL Server application-consistent backup action will
perform a full image-level backup. Ad-hoc (on demand) runs of this workflow will also
create full backups, even when started at off-schedule times. If you also select
transaction log backup in the Policy Action wizard, the transaction log backup will

100 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

occur as part of incremental backups after the initial full backup, at the interval set in
the workflow properties.

Starting, stopping, and restarting policies

The workflows in a policy can run automatically, based on a schedule. You can also
manually start, stop, and restart specific workflows by using the the NMC NetWorker
Administration Monitoring window.
You can restart any failed or canceled workflow. Note, however, that the restart must
occur within the restart window that you specified for the workflow. Additionally, for a
VMware backup, if you cancel a workflow from NetWorker Administration and then
want to restart the backup, ensure that you restart the workflow from the NetWorker
Administration window. If a workflow that was started from NetWorker
Administration is restarted from the vSphere Web Client, the backup fails.
Procedure
1. In the Monitoring window, select the workflow or actions.
2. Right-click and then select Start, Stop, or Restart.
A confirmation message appears.

Note

You cannot stop, restart, or start individual actions.

3. Click Yes.

Enabling a VMware group with Dynamic Association and applying rules in

NMC
When you create or edit a VMware protection group in NMC, enabling the Dynamic
Association option for the group will allow you to assign rules. Rules can be used to
determine which virtual machines and containers will be protected by the group in
addition to any objects that have been manually selected for inclusion. Note that you
can only use the NMC NetWorker Administration window to create rules and assign
rules to a group. These operations are not supported from the command line or the
vCenter plug-in.

A VMware group with Dynamic Association enabled can include both static and
dynamic objects:
l Virtual machines and containers from the vCenter that are manually selected when
you create or edit the group in NMC are known as static objects, because their
inclusion in the group does not change unless you unselect an item.
l Virtual machines and containers that are only included in the group according to
the rules assigned when you create or edit the group in NMC are known as
dynamic objects, because their inclusion in the group can change over time based
on whether the items continue to match the rule criteria.
When creating or editing the group, you can preview both static and dynamic contents
to ensure that the protection policy will include all the virtual machines and containers
that you want protect in the backup. Additionally, you can specify a virtual machine
exclusion list for the VMware protection group to exclude particular virtual machines
or VMDKs from being backed up as part of the group.
When a VMware protection group is associated with one or more rules, the rules are
executed against the vCenter inventory when the policy backup is started in order to
filter the group contents according to the rule criteria.

Starting, stopping, and restarting policies 101

Protecting virtual machines

Creating and viewing tags in the vSphere Web Client

In order to support the dynamic selection of VMware objects based on the user-
defined rules created in NMC, virtual machine tags in the vSphere Web Client allow
you to attach metadata to the objects in the vSphere inventory to make these objects
easier to sort and search. Tags are supported in vSphere versions 6.5 and later.
When you create a tag in the vSphere Web Client, the tag can be assigned to a
category in order to group related tags together. When defining a category, you can
also specify the object types the tags will be applied to, and whether more than one
tag in the category can be applied to an object. Within a single rule, there is a
maximum limit of 50 rule definitions applicable to tags and categories, as shown in the
following example where Category is the category name and Bronze is the tag name:
l Category:Category1,Tag:Bronze1
l Category:Category2,Tag:Bronze2
l Category:Category3,Tag:Bronze3
l and so on up to Category:Category50,Tag:Bronze50
In the above example, if the number of characters associated with category name or
tag name are more than 9 or 7 characters respectively, then the maximum limit for
rule definitions in a single rule will be further reduced from 50. Exceeding the
maximum limit for rule definitions will result in no virtual machines being backed up as
part of this group, since there will be no members associated with the group. As a best
practice, it is recommended to keep the number of rule definitions within a single rule
to 10 or less and, in cases where there are a large number of rule definitions within a
single rule, it is also recommended to keep the number of characters in category/tag
names to 10 or less.
The vSphere Web Client displays any tags that have been created for the vCenter
under Tags & Custom Attributes in the left pane. When you click Tags & Custom
Attributes, select the Tags tab. A table lists the available tags. Click on a tag link in
the table to view the virtual machines associated with this particular tag.

Note

Once virtual machines are associated with tags, the association will not be reflected in
the NMC NetWorker Administration window's VMware View until the timeout
period has completed. The default timeout for NetWorker to fetch the latest inventory
from vCenter is 15 minutes.

Rules in the NMC NetWorker Administration window

Rules are used to automatically map VMware objects (virtual machines and
containers) to a group by using one or more filtering mechanisms, according to the
following supported rule criteria:
l Type: The VMware object type. Available selections include VM, VApp, VM Folder,
Datacenter, Cluster, or Resource Pool.
l Properties: The object type properties that the rule uses to determine a match.
These properties include the object's name, path or a tag that you've created, and
available properties depend on the object type, as specified below.
Cluster - Path, tag
VMfolder - Name, path, tag
Datacenter - Name, path, tag
ResourcePool - Path, tag
VirtualMachine - Name, tag
vApp - Name, tag

102 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

l Operator: Uses the object type properties to further define how a match is made.
Available selections include Equals, DoesNotEqual, StartsWith, DoesNotStartWith,
Contains, DoesNotContain, EndsWith, DoesNotEndWith, or Regular expression.
For example, for an object type VirtualMachine with the Name property selected, you
can select "equals" to create a rule where the virtual machine will only be included in
the group when the entire name is specified, or "contains" to include the virtual
machine in the group whenever a specific text string appears in the virtual machine
name.
Additionally, if you create multiple rules, you can select All from the Match type drop-
down if the item has to meet all of the rules criteria in order to be included in the
group, or select Any from the drop-down to include the item if the item meets any of
the criteria.

Note

Rule definitions for NetWorker vProxy policies with dynamic association enabled can
contain regular expressions. The appendix Regular expressions for NetWorker vProxy
dynamic policies rule definitionsdescribes the acceptable rules, syntax, and grammar
to use when writing such regular expressions.

Create a rule in NMC and associate the rule to a VMware group

To create a rule or access existing rules in NMC, and apply these rules to a VMware
group, perform the following.
Before you begin
Create the VMware group and associate the group with a policy/workflow, as outlined
in the previous sections.
Rules can only be applied to VMware groups in NMC when you enable the Dynamic
Association option. When a group is enabled with Dynamic Association, rules are
executed against the vCenter inventory to determine which VMware objects will be
dynamically added to the VMware protection group's contents, based on matching the
rule criteria.
Procedure
1. In the NetWorker Administration window, click Protection, and then select
Rules in the left navigation pane.
Any rules that have already been created appear in the right pane.
2. Right-click Rules and select New from the drop-down.
The Create Rule window displays.

Enabling a VMware group with Dynamic Association and applying rules in NMC 103
Protecting virtual machines

Figure 17 Create a new rule to apply to a VMware group

3. In the General tab, type a name for the rule, and select the Datastore Type
from the drop-down. The default Datastore Type is VMware.
4. In the Rule Definition pane, click Add.
5. In the Rule Definition pane:
a. For the Type column's drop-down, select the object type, for example,
VirtualMachine.
b. For the Property column's drop-down, select from one of the available
options, for example, Tag.
c. For the Operator column's drop-down, select from one of the available
options, for example, Equals.
d. Click Browse to display a list of all the categories and tags that have been
created on that vCenter server. Select the tag you want to apply to the rule
and click OK to exit the dialog.

Note

Tags are only supported in vSphere versions 6.5 and later.

6. Repeat steps 2 through 5 for any additional rules you want to create.

Note

If adding multiple rules, in order to specify whether to apply more than one rule
to the group, select either All or Any from the Match Type drop-down.

7. When finished adding rules, return to the Protection window and right-click the
desired group in the left pane, and then select Properties from the drop-down.
The Edit Group window displays.
8. If not already selected, select the Dynamic Association checkbox, and then
select any virtual machine(s) in this workflow that you want to include in the
group regardless of the rules applied. These objects are known as static objects.

104 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

9. Select the desired rule from the Rule drop-down that you want to apply to the
other virtual machines in the workflow to determine which objects will be
dynamically included.
10. Click Preview All Virtual Machines to view a list of the static and dynamic
virtual machines and objects that have been added to the group. In this window,
you can also unselect a virtual machine or VMDK to exclude the item from the
backup. When an object is unselected, an entry for the object appears in the
Excluded VM list.
11. Save the changes in the Edit Group window, and close the window.
Results
When you select the specific VMware group in the Protection window, the vCenter
Objects Selected field displays the list of virtual machines that are statically selected.
Similarly, Protected VMs in VMware View only displays the virtual machines that are
statically protected.

Visual representation of VMware policy and associated actions

A visual representation of the VMware backup policy with its associated workflow and
actions appears in the lower panel of the Protection window.
Figure 18 VMware protection policy in the Protection window

The Media window displays the save sets contained within the policy. If the save sets
are additionally part of an application-consistent policy, a green check mark appears in
the VM App Consistent column.

Visual representation of VMware policy and associated actions 105

Protecting virtual machines

Figure 19 VMware protection policy save sets in Media window

VMware View in NMC

VMware View provides an overview of the vCenter environment. You can access
VMware View from the NetWorker Administration Protection window.
If you have not yet added a vCenter server to VMware View, right-click VMware
View in the right pane, and select Add vCenter from the drop-down. The Add
vCenter dialog displays.
Figure 20 Add a vCenter server to VMware View in NMC

In the Host Name field, type the IP address of the host, and provide the vCenter
Server username and password credentials. Additionally, if the vCenter server is
deployed in the Cloud, select the Deployed in Cloud checkbox, and then click OK.

Note

When you select Deployed in Cloud, a parameter displays in the backup action logs
that indicates HypervisorMode: VMC. When the checkbox is not selected, the
parameter indicates HypervisorMode: vSphere.

106 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

When you add the vCenter server to VMware View, the following actions occur:
l A visual (map) or tabular representation of the vCenter environment appears in
the VMware View window.
l A client resource is created for the vCenter server with the vProxy backup type.
Using VMware View, you can also assign the policies you created in "VMware data
protection policies in NMC." to the vCenter objects.
The following sections describe the options that are available in VMware View.

Map view of the VMware environment

When you expand VMware View, a hierarchical display of the VMware environment
appears. The following containers appear:
l vCenters
l DataCenters within the vCenter
l Clusters within the DataCenter
l ESX servers
l Folders above the DataCenters and folders above ESX hosts/clusters
l vApps
l Resource Pools
You can use several operations to navigate within the map view:
l To zoom in and out of the map view, select the zoom icons on the map view icon
bar or click on the right details pane and scroll with the mouse wheel. You can also
click the Zoom Area button to select an area to zoom into, or click the Fit
Content button to fit the entire display into the right details pane. These
operations are also available when you right-click the details pane.
l To move the graphical display, left-click in the details pane and drag the mouse
cursor.
l To expand or collapse any container in the map view to display or hide the child
elements associated with the container, double-click the container.
l To display an overview of the map view, select the Overview tab within the
Overview pane. The overview of the map view is particularly useful for large maps
and allows you to quickly drill down to specific areas in the map.
l To limit items displayed and search for specific items in the map view, use the
Filter VM by and Show functions, available from the Filter tab within the
Overview pane.
When you click on any container, the hierarchical tree provides a detailed map view of
that container and all of its children. For example, select the top level virtualization
node to display a complete view of your VMware environment across all configured
vCenters, or select an individual ESX server or Cluster in the hierarchy to display the
resource pool with all child elements associated with that ESX server or Cluster
including VMs, VMDKs, the vProxy appliance, and any associated VMware backup
policies to the right of these containers.
Lines connect each child element to the parent element, with child elements
proceeding hierarchically from left to right in the display, as shown in the following
figure.

VMware View in NMC 107

Protecting virtual machines

Figure 21 Map view of VMware environment in NMC

To refine items displayed in the right details pane, select containers in the
Virtualization node hierarchy in the left pane. For example, if an individual Cluster is
selected in the Virtualization node, only child elements associated with that Cluster
display.

108 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Figure 22 Cluster with child elements in VMware View

To filter the visible items to show only protected VMs, unprotected VMs, or
overprotected VMs, click the links located above the right pane, as shown in the
following figure.

Note

When you enable a VMware group with Dynamic Association, the protected VMs
reflect those virtual machines that are statically protected, and does not include
virtual machines that get dynamically added to the group after rules are applied.

VMware View in NMC 109

Protecting virtual machines

Figure 23 Filtering results in VMware View

Table view of the VMware environment

To switch to a view of the VMware environment in table form, right-click anywhere in
the details pane and select Table. The Table view functions like other table views in
the Administration window.

Note

Table view only displays information for virtual machines. It does not show any details
about VMDKs. You must use Map view to display those details.

Figure 24 VMware table view

110 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

The filtering function works the same in Table view as in Map view. Links provided
above the details pane allow you to display only overprotected virtual machines,
unprotected virtual machines, or all virtual machines in the environment. The
NetWorker Administration Guide provides general information on using tables in the
Administration window.

Note

In Table view, the Host field contains an undefined value for virtual machines or
containers that are part of a cluster. The Map view provides a link to the cluster.

Assigning protection groups to virtual machines

From within the map or table view of the VMware environment, you can assign
protection groups at any level, for example, you can assign a group to the entire
datacenter, a cluster, a resource pool, a virtual machine, or even a VMDK by using
VMware View.
Procedure
1. Right-click on any container, or expand the container, and then right-click on an
element within VMware View.
2. Select Add to Group.
The available groups display, as shown in the following figure.
Figure 25 Add group in VMware View

3. Select a group, and click OK.

VMware View refreshes and displays the new association.
4. To assign a group at the VMDK level, expand a virtual machine, right-click the
VMDK that you want to associate to the group, and select Add to Group.

Assigning a group to a disconnected ESX server

When you disconnect an ESX host from the vCenter server, the ESX still appears in
VMware View. You can assign a group to an ESX host that is disconnected from the

VMware View in NMC 111

Protecting virtual machines

vCenter server, however, if you start the group, the group will remain in “interrupted”
state until you reconnect the ESX back to the vCenter server and run the group again.

Note

Disconnecting an ESX server from a vCenter server only temporarily disconnects the
server and does not remove the server. To permanently remove the ESX server from
the vCenter inventory, use the Remove command from vCenter.

vProxy backup workflows in the vSphere Client's Dell EMC

NetWorker interface
The NetWorker vProxy workflows can only be created in NMC, however, you can
perform virtual machine backups of these vProxy workflows, and add virtual machines
to the vProxy workflows, by using the Dell EMC NetWorker interface within the
vSphere Client.
Dell EMC NetWorker appears in the left navigation pane of the vSphere Client after
you install the vCenter plug-in. The section Installing the vCenter plug-in provides
instructions.

Note

Backup and recovery operations in the vSphere Client Dell EMC NetWorker
interface are not supported for SQL Server advanced application-consistent
protection policies. Perform these operations from the NMC NetWorker
Administration window or the Dell EMC Data Protection Restore Client.

Connect to the NetWorker server in the vSphere Client

You must establish a connection to the NetWorker server before performing any
vProxy backup and recovery operations in the vSphere Client.
Before you begin
Dell EMC NetWorker only appears in the vSphere Client after you install the vCenter
plug-in. The section Installing the vCenter plug-in provides instructions.
Procedure
1. Login to the vSphere Client as an administrator, or as a non-administrator
Active Directory user that you created using the steps in the section Using the
vCenter plug-in as a non-administrator Active Directory user.
2. In the vSphere Client, select Menu > Dell EMC NetWorker, or select Dell
EMC NetWorker in the left pane.

112 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Figure 26 Accessing Dell EMC NetWorker in the vSphere Client

A prompt displays in the right pane with fields required to connect to the
NetWorker server.
3. For the NetWorker server, type the following information:
a. In the Username field, type the NetWorker administrator username.
b. In the Password field, type the NetWorker administrator password.
c. In the NetWorker Server field, type the IP address of the NetWorker
server.
d. In the Port field, type 9090.
Figure 27 NetWorker connection information in the vSphere Client

4. Click Log in.

Results
When a connection to the NetWorker server is established, the Basic Tasks pane
appears, as shown in the following.

Connect to the NetWorker server in the vSphere Client 113

Protecting virtual machines

Figure 28 Dell EMC NetWorker Basic Tasks pane

Accessing the vCenter plug-in as a non-administrator Active Directory user

You can only access the vCenter plug-in (the Dell EMC NetWorker interface) in the
vSphere Client if you are an NetWorker administrator or a non-administrator Active
Directory user associated with appropriate privileges in NetWorker. The following
procedure describes how to access the plug-in as a non-administrator Active Directory
user.
Before you begin
Install the vCenter plug-in. The section Installing the vCenter plug-in provides
instructions.
Procedure
1. Create a vmwareAdmin group in NetWorker that contains the following
privileges at a minimum:
l View Security Settings
l View Application Settings
l Remote Access All Clients
l Operate NetWorker
l Monitor NetWorker
l Operate Devices and Jukeboxes
l Recover Local Data
l Recover Remote Data
l Backup Local Data

2. Create an Active Directory user within your desired security group.

3. Add the user and group to the NetWorker Management Console's External
Roles attribute. For example:
CN=VMwareTeam,CN=Users,DC=vproxy,DC=com

114 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

cn=VMwareUser,cn=Users,dc=vproxy,dc=com
where VMwareTeam is the security group name, and VMwareUser is the Active
Directory user name.
4. Log in to the vSphere Web Client as the Active Directory user, in the format
<tenant>\<domain>\<userid>. For example:

default\vproxy\VMwareUser

Results
The Active Directory user that you create using these steps will only have access to
the vSphere Client Dell EMC NetWorker interface, and cannot be used to log in to
NetWorker Management Console. If you also need to provide access to NMC, then
add those required privileges accordingly.

Start a vProxy policy in the vSphere Client Dell EMC NetWorker interface
To start a vProxy backup policy by using the Dell EMC NetWorker interface in the
vSphere Client, perform the following steps.
Procedure
1. In the vSphere Client, if not already selected, click Dell EMC NetWorker in the
left pane.
When a connection to the NetWorker server is established, links to Basic Tasks
appear in the right pane.
2. From the Basic Tasks pane, click Assign Backup Policy, or click the Protection

icon in the vertical navigation bar.

The vCenter server hosts associated with the NetWorker server display. When
you select one of these entries, a list of available vProxy policies that were
created in NMC displays in the right pane.
Figure 29 Policies pane with available vProxy policies

3. Click the arrow to the left of a policy to expand and view the policy and
workflow details. You can click the Items link under the Workflow to display the
virtual machines protected by this workflow.

Start a vProxy policy in the vSphere Client Dell EMC NetWorker interface 115
Protecting virtual machines

4. If you do not need to add or remove any virtual machines from the workflow,
click the three dots next to the policy and select Backup all sources or Backup
only out of date sources from the drop-down.
Figure 30 Policy backup options

Results
A dialog displays indicating that the policy was successfully started. To close the
dialog, click OK. You can then click the blue arrows in the lower right corner of the
window to monitor the progress of the policy in the Recent Tasks pane.
Figure 31 Recent Tasks pane

Add virtual machines to a vProxy policy in the vSphere Client Dell EMC
NetWorker interface
Perform the following steps to edit a vProxy policy to add virtual machines to a
workflow by using the Dell EMC NetWorker interface in the vSphere Client.
Procedure
1. In the vSphere Client, if not already selected, click Dell EMC NetWorker in the
left pane.
When a connection to the NetWorker server is established, links to Basic Tasks
appear in the right pane.
2. Click Assign Backup Policy.
A list of available vProxy policies that were created in NMC displays in the right
pane.

116 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Figure 32 Policies pane with available vProxy policies

3. Click the arrow to the left of a policy to expand and view the policy and
workflow details. You can click the Items link under the Workflow to display the
virtual machines protected by this workflow.
4. To add virtual machines to the workflow, click the three dots next to the policy
and select Edit from the drop-down.
Figure 33 Edit a vProxy policy

The Editing backup policy dialog displays with available backup sources.
5. Select any virtual machines or VMDKs in the inventory you want to protect with
this workflow, and then click Finish.

Add virtual machines to a vProxy policy in the vSphere Client Dell EMC NetWorker interface 117
Protecting virtual machines

Figure 34 Backup sources in the Editing backup policy dialog

Results
Any virtual machines or VMDKs added to the workflow now appear when you click the
Items link under the workflow in the Policies pane.

vProxy workflows in the vSphere Web Client's VM Backup

and Recovery interface
The flash-based vCenter plug-in, which displays as the VM Backup and Recovery
interface in the vSphere Web Client, was introduced in NetWorker 9.1. New and
upgraded users of NetWorker version 18.1 can still use this plug-in to run virtual
machine backups from the vProxy workflows created in NMC, and add virtual
machines to those vProxy workflows.
VM Backup and Recovery appears in the left navigation pane of the vSphere Web
Client when you install the flash-based vCenter plug-in. The section Installing the
vCenter plug-in provides instructions.

Note

Backup and recovery operations in the vSphere Web Client VM Backup and
Recovery interface are not supported for SQL Server advanced application-
consistent protection policies. Perform these operations from the NMC NetWorker
Administration window or the Dell EMC Data Protection Restore Client.

Connect to the NetWorker server in the vSphere Web Client

After installing the vCenter plug-in, you must establish a connection to the NetWorker
server before performing any vProxy operations in the vSphere Web Client.
Procedure
1. Log in to the vSphere Web Client as an administrator, or as a non-
administrator Active Directory user that you created using the steps in the
section Using the vCenter plug-in as a non-administrator Active Directory user.
2. In the vSphere Web Client, click VM Backup and Recovery in the left pane.
The required NetWorker connection information appears in the right pane.

118 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Figure 35 NetWorker connection information in the vSphere Web Client

3. Enter the following information for the NetWorker server:

a. In the Host field, type the IP address of the NetWorker server.
b. In the Port field, type 9090.
c. In the User field, type the NetWorker administrator username.
d. In the Password field, type the NetWorker administrator password.
4. Click Connect.
Results
When a connection to the NetWorker server is established, the Getting Started pane
appears.

Accessing the vCenter plug-in as a non-administrator Active Directory user

You can only access the vCenter plug-in (the VM Backup and Recovery interface) in
the vSphere Web Client if you are an NetWorker administrator or a non-administrator
Active Directory user associated with appropriate privileges in NetWorker . The
following procedure describes how to access the plug-in as a non-administrator Active
Directory user.
Before you begin
Install the vCenter plug-in. The section Installing the vCenter plug-in provides
instructions.
Procedure
1. Create a vmwareAdmin group in NetWorker that contains the following
privileges at a minimum:
l View Security Settings
l View Application Settings
l Remote Access All Clients
l Operate NetWorker
l Monitor NetWorker
l Operate Devices and Jukeboxes
l Recover Local Data
l Recover Remote Data

Connect to the NetWorker server in the vSphere Web Client 119

Protecting virtual machines

l Backup Local Data

2. Create an Active Directory user within your desired security group.

3. Add the user and group to the NetWorker Management Console's External
Roles attribute. For example:
CN=VMwareTeam,CN=Users,DC=vproxy,DC=com
cn=VMwareUser,cn=Users,dc=vproxy,dc=com
where VMwareTeam is the security group name, and VMwareUser is the Active
Directory user name.
4. Log in to the vSphere Web Client plug-in as the Active Directory user, in the
format <tenant>\<domain>\<userid>. For example:
default\vproxy\VMwareUser

Results
The Active Directory user that you create using these steps will only have access to
the vSphere Web Client VM Backup and Recovery interface, and cannot be used to
log in to NetWorker Management Console. If you also need to provide access to NMC,
then add those required privileges accordingly.

Starting a vProxy policy in the vSphere Web Client

Perform the following steps to start a vProxy policy and workflow created in NMC by
using the vSphere Web Client.
Procedure
1. In the vSphere Web Client, click VM Backup and Recovery in the left pane.
When a connection to the NetWorker server is established, the Getting
Started pane appears.
2. Click the Backup tab to open the Backup pane.
Any vProxy policies created in NMC display.

120 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Figure 36 Backup pane with vProxy policy

3. Highlight the policy and workflow you want to run and click Backup now in the
top-right corner.

Results
You can monitor the progress of the backup in the Running tab of the Recent Tasks
pane.

Note

If you cancel a workflow from the vSphere Web Client and then want to restart the
backup, ensure that you restart the workflow from the vSphere Web Client. If a
workflow that was started from the vSphere Web Client is restarted from the NMC
NetWorker Administration window, the backup fails.

Adding virtual machines to a vProxy policy workflow in the vSphere Web

Client
Perform the following steps to add virtual machines to a vProxy workflow created in
NMC by using the vSphere Web Client.
Procedure
1. In the vSphere Web Client, click VM Backup and Recovery in the left pane.
When a connection to the NetWorker server is established, the Getting
Started pane appears.
2. Click the Backup tab to open the Backup pane.
Any vProxy policies created in NMC display.
3. Highlight the policy whose workflow you want to add virtual machines to and
click Edit in the top-right corner.
The Editing backup policy window displays with available backup sources.

Adding virtual machines to a vProxy policy workflow in the vSphere Web Client 121
Protecting virtual machines

Figure 37 Backup sources in the Editing backup policy window

4. Select any virtual machines or VMDKs in the inventory you want to protect with
this workflow and click Finish.
Results
Any virtual machines or VMDKs added to the workflow appear under Sources in the
bottom of the Backup pane.

Troubleshooting Data Protection Policies

This section provides information about issues related to configuring Data Protection
Policy resources and with backup and recovery operations.

Backup operations
The following troubleshooting items provide some direction on how to identify and
resolve common issues with NetWorker VMware Protection backups for the VMware
Backup Appliance (VBA).

SQL Server application-consistent backups fail with error "Unable to find VSS metadata files in
directory"
SQL Server application-consistent virtual machine backups might fail with the
following error when the disk.enableUUDI variable for the virtual machine is set to
False.
Unable to find VSS metadata files in directory C:\Program Files
\DPSAPPS\MSVMAPPAGENT\tmp\VSSMetadata.xxxx.
To resolve this issue, ensure that the disk.enableUUDI variable for the virtual machines
included in an SQL Server application-consistent backup is set to True.

Failed to lock Virtual Machine for backup: Another EMC vProxy operation 'Backup' is active on
VM
This error message appears when a backup fails for a virtual machine, when previous
backups of the virtual machine was abruptly ended and the VM annotation string was
not cleared.
To resolve this issue, clear the annotation string value for the virtual machine.

122 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

1. Connect to the vCenter server and navigate Home > Inventory > Hosts and
Clusters.
2. Select the virtual machine, and then select the Summary tab.
3. Clear the value that appears in the EMC Proxy Session field.

“Loading backup job data”

This message can appear for up to five minutes when you select a large number of
VMs (approximately 100 VMs) for a single backup job. This issue can also apply to
lock/unlock, refresh, or delete actions for large jobs. This is expected behavior when
you select a very large number of jobs. This message disappears when the action is
completed, which can take up to five minutes.

“The following items could not be located and were not selected {client name}.”
This error can occur when the backed up VM(s) cannot be located during Edit of a
backup job. This is a known issue.

Windows 2008 R2 VMs may fail to backup with “disk.EnableUUID” configured to “true.”
Windows 2008 R2 backups may fail if the VM is configured with the disk.EnableUUID
parameter set to true. To correct this problem, manually update the vmx configuration
parameter disk.EnableUUID to false by using the vSphere Web Client:
1. Shut down the VM by right clicking the VM and selecting Shut Down Guest OS.
2. Right click the VM and select Edit Settings.
3. Click VM Options.
4. Expand the Advanced section and click Edit Configuration.
5. Locate the name disk.EnableUUId and set the value to false.
6. Click OK on the next two pages.
7. Right click the VM and select Power On.
After you update the configuration parameter, the backups of the Windows 2008 R2
VM should succeed.

When VMs are moved in or out of different cluster groups, associated backup sources may be
lost
When you move hosts into clusters with the option to retain the resource pools and
vApps, the containers get recreated, not copied. As a result, the container is no longer
the same container even though the name is the same. To resolve this issue, validate
or recreate any backup jobs that protect containers after moving hosts in or out of a
cluster.

vMotion operations are not allowed during active backup operations

The vSphere vMotion feature enables the live migration of running virtual machines
from one physical server to another. You cannot run vMotion operations on the vProxy
appliance or VMware Backup appliance during active backup operations. This is
expected behavior. Wait until all backup operations have completed prior to
performing a vMotion operation.

Backup operations 123

Protecting virtual machines

Backups fail if certain characters are used in the virtual machine name, datastore, folder, or
datacenter names
When you use spaces or special characters in the virtual machine name, datastore,
folder, or datacenter names, the .vmx file is not included in the backup. The vProxy
appliance and VMware Backup appliance do not back up objects that include the
following special characters, in the format of character/escape sequence:
l & %26
l + %2B
l / %2F
l = %3D
l ? %3F
l % %25
l \ %5C
l ~ %7E
l ] %5D

NSRCLONE failed for one or more savesets

This message appears during a clone action and NetWorker does not clone all save
sets.
Error messages similar to the following also appear:
[CLONE SKIPPED SAVESETS]
ssid/cloneid;
Action clone 'name' with job id 5 is
exiting with status 'failed', exit code 1
NSRCLONE failed for one or more savesets

To resolve this issue, increase the values in the max target sessions and target
sessions attributes for the clone device. The NetWorker Administration Guide describes
how to modify the properties of a device.

Lock placed on virtual machine during backup and recovery operations continues for 24 hours if
vProxy appliance fails
During vProxy backup and recovery operations, a lock is placed on the virtual machine.
If a vProxy appliance failure occurs during one of these sessions, the lock gets
extended to a period of 24 hours, during which full backups and transaction log
backups will fail with the following error until the lock is manually released:
Cannot lock VM 'W2K8R2-SQL-2014' (vm-522): Another EMC vProxy
operation 'Backup' is active on VM vm-522.

Workaround
To manually release the lock on the virtual machine:
1. Open the vSphere Web Client.
2. Click on the virtual machine and select Summary.
3. Select Custom attribute and click Edit.

124 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

4. Remove the attribute EMC vProxy Session.

Trailing spaces not supported in SQL database names

Due to a VSS limitation, you cannot use trailing spaces within the names of SQL
databases protected by a NetWorker application-consistent data protection policy.

SQL databases skipped during virtual machine transaction log backup

When an advanced application-consistent policy is enabled with transaction log
backup, the msvmagent_appbackup.exe program evaluates databases to
determine if transaction log backup is appropriate.
If transaction log backup is not appropriate for a database, the database will
automatically be skipped. Databases are skipped for the following reasons:
Case Description
Database has When a database has been restored, this database will be skipped during
been restored transaction log backup because there is no Backup Promotion.

System System databases are automatically skipped for transaction log backup.
Database

Database State Database is not in a state that allows backup. For example, the database is in
the NORECOVERY state.

Recovery Database is in SIMPLE recovery model, which does not support transaction
Model log backup

Other Backup Most recent backup for the database was performed by a different backup
Product product.

New Database Database was created after most recent full backup.

Backup Failure Database was in state to allow backup, backup was attempted, but backup
failed.

All skipped databases will be backed up as part of the next full backup. Also, a skipped
database will not result in msvmagent_appbackup.exe failure. The only instance in
which msvmagent_appbackup.exe would potentially fail is if all databases failed to
back up.
The msvmagent_appbackup.exe program generates a history report of the
databases, if the database backup status was success/skipped/failed, and a reason if
they were skipped or failed if applicable. This history report is visible in the action logs
for the vProxy, which are available on the NetWorker server and also available on the
client as part of the appbackup logs.

Note

For SQL virtual machine application-consistent data protection, the SQL and
operating system versions follow the NMM support matrix available at http://
compatibilityguide.emc.com:8080/CompGuideApp/.

Increase the vCenter query timeout before starting a VMware backup action
Before starting a VMware backup action, NetWorker queries the vCenter server to
determine if any changes have occurred in the items selected for backup. You can

Backup operations 125

Protecting virtual machines

increase the timeout value by setting the

NSR_HYPERVISOR_QUERY_REQUEST_TIMEOUT environment variable.
The amount of time for the query to complete depends on several factors, including
the network response time, the size of the vCenter, and the number of resources free
on the NetWorker server. The default timeout of the query is 30 minutes, after which
the backup fails with the following error:
nsrvproxy_save NSR warning Dispatcher: Request timed out
Perform the following steps to set the
NSR_HYPERVISOR_QUERY_REQUEST_TIMEOUT environment variable to a higher
timeout value. Note that the timeout value is in seconds. In this example, a value of
2700 (or 45 minutes) is used.
1. Set up the environment variable:
l On Linux, add the following lines to the /nsr/nsrrc file:
NSR_HYPERVISOR_QUERY_REQUEST_TIMEOUT=2700
export NSR_HYPERVISOR_QUERY_REQUEST_TIMEOUT
l On Windows, add a new variable called
NSR_HYPERVISOR_QUERY_REQUEST_TIMEOUT under Environment
variables > System variables, and specify a value of 2700.
2. On the NetWorker server, connect to nsradmin:
nsradmin -p nsrexec
3. Select/Print the 'NSRLA' resource:
p type: nsrla
4. Append to the attribute:
append environment variable names:
NSR_HYPERVISOR_QUERY_REQUEST_TIMEOUT
5. Select/Print the 'NSRLA' resource again to verify your changes:
p type: nsrla
The last attribute should display as environment variable names:
NSR_HYPERVISOR_QUERY_REQUEST_TIMEOUT.

vProxy backup log files

You can use vProxy session log files to troubleshoot backup failures.
The following table provides information about the vProxy backup log files. located
in /opt/emc/vproxy/runtime/logs/vbackupd/ on the vProxy host. Note that
old daemon and session logs are located in /opt/emc/vproxy/runtime/logs/
recycle/.

Table 13 Backup log files

Log file Log location Description

Session <session-uuid>.log Contains processing details for a session. Sessions
logs display as “Recycled” when the session is deleted. The
log level is configured in the session request.

Daemon <daemon>- Records requests and problem events which may

logs engine.log require administrative action in vProxy or vCenter.
Error and Panic messages from the session logs are
also recorded in the daemon log. The log level is set

126 NetWorker 18.1 VMware Integration Guide

 Protecting virtual machines

Table 13 Backup log files (continued)

Log file Log location Description

in /usr/lib/systemd/system/
<daemon>.service, for example, "--engine-log-level
<level>".

DD Boost <daemon>-boost.log The log level is set in /usr/lib/systemd/

backup system<daemon>.service, for example, "--boost-
log log-level <level>"

VDDK <daemon>-vddk.log The log level is set in /opt/emc/vproxy/conf/

backup VixDiskLib.config (vixDiskLib.transport.LogLevel
log = <level>)

On the NetWorker server, the location of log files for individual backups differ on
Windows and LINUX:
l Linux—/nsr/logs/policy/policy_name
l Windows—C:\Program Files\EMC NetWorker\logs\policy
\policy_name
where policy_name is the name of the policy resource associated with the backup
action.
Additional logging with the VMBackup broker
Debug logging of the vmbackup broker of nsrd is disabled by default. To turn on
additional logging, you can touch an empty file at <nsr>/tmp/vmbackup_logging.
Enabling of additional logging can be performed while other operations are in progress,
and a NetWorker restart is not required. To turn off additional logging, you can
remove the same file.

NMC function to collect vProxy log bundle information

NetWorker 18.1 features an NMC function to collect vProxy log bundle information
from a virtual machine. To collect log bundle information, perform the following steps
in NMC:
1. From NMC's NetWorker Administration, open the Devices window.
2. From the left pane, select VMware Proxies to display the virtual machine proxy
devices.
3. Right-click the virtual machine that you want to collect log bundle information
from, and then from the menu, click Log Bundle.

Note

If you are accessing NMC from a remote machine that cannot communicate with
vProxy, NMC fails to collect the log bundle.

NMC function to collect vProxy log bundle information 127

Protecting virtual machines

Logs for SQL application-consistent data protection

The following section provides location information for all logs associated with SQL
application-consistent data protection.

Note

In order to increase the debug level for SQL application-consistent virtual machine
(MSVMAPPAGENT) backups, use dbgcommand, For example, dbgcommand -p
<nsrd-pid> Debug=9. Once you complete the debugging session, ensure that you
reset the debug level of nsrd to zero by running dbgcommand <nsrd-pid>
Debug=0.

MSVMAPPAGENT logs
You can access logs related to MSVMAPPAGENT from the following locations:
l Discovery log: C:\Program Files\DPSAPPS\MSVMAPPAGENT\logs
\msvmagent_discovery.log
l FULL backup: C:\Program Files\DPSAPPS\MSVMAPPAGENT\logs
\msvmcatsnap.log
l Transaction log backup: C:\Program Files\DPSAPPS\MSVMAPPAGENT\logs
\msvmagent_appbackup.log
l Restore of FULL backup: C:\Program Files\DPSAPPS\MSVMAPPAGENT
\logs\msvmagent_snapshotrestore.log
l Restore of transaction log backup: C:\Program Files\DPSAPPS
\MSVMAPPAGENT\logs\msvmagent_apprestore.log
vProxy logs
You can access these vProxy logs from the following locations:
l FULL and transaction log backups: /opt/emc/vproxy/runtime/logs/
vbackupd/BackupVmSessions-sessionnumber.log
l InspectBackup logs: /opt/emc/vproxy/runtime/logs/vsessionsd/
inspectBackup-sessionnumber.log
l Mount session logs: /opt/emc/vproxy/runtime/logs/vflrd/mount-
sessionnumber.log
l Browse session logs: /opt/emc/vproxy/runtime/logs/vflrd/browse-
sessionnumber.log
l Recover App sessions logs: /opt/emc/vproxy/runtime/logs/vflrd/
application-sessionnumber.log. Note that a few minutes after
completion, these logs are moved to /opt/emc/vproxy/runtime/logs/
recycle/.

128 NetWorker 18.1 VMware Integration Guide

CHAPTER 4
Recover virtual machines and data

This chapter contains the following topics:

l vProxy recovery in NMC...................................................................................130

l vProxy recovery in the NetWorker Management Web UI.................................. 151
l vProxy file-level restore and SQL restore in the Dell EMC Data Protection
Restore Client...................................................................................................159
l vProxy recovery in the vSphere Client's Dell EMC NetWorker interface.......... 186
l vProxy recovery in the vSphere Web Client's VM Backup and Recovery interface
..........................................................................................................................197
l vProxy recovery log files..................................................................................205

Recover virtual machines and data 129

Recover virtual machines and data

vProxy recovery in NMC

You can use the Recovery wizard in NMC to perform image level recovery, which
allows you to recover full virtual machines and VMDKs. You can also use the Recovery
wizard to perform file-level restore from a primary or cloned backup on a Data Domain
device, but only as an administrator.
In NMC's NetWorker Administration window, click Recover. From the Recover
window, launch the Recovery wizard by selecting Recover > New.

Entering management credentials for the Data Domain resource (instant

recovery and User mode file-level restore only)
Before you perform an instant recovery of a virtual machine or file-level restore (User
mode), ensure that you provide the management credentials for the Data Domain
resource. For instant recovery, these credentials are required when performing the
recovery using the NMC Recover wizard or the VM Backup and Recovery interface
in the vSphere Web Client.
Procedure
1. In the NMC Administration window, click Devices.
The Devices window displays.
2. In the expanded left navigation pane, select Data Domain Systems.
3. In the right details pane, right-click the Data Domain system, and then select
Properties.
The NSR Data Domain Properties window displays.

130 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 38 NSR Data Domain Properties

4. In the Access pane, type the management credentials.

a. In the Management host field, specify the hostname of the Data Domain
system that is used for management commands.
b. In the Management user field, specify the username for a Data Domain user
that has admin access. For example, sysadmin. The Management user should
have Data Domain administrator privileges.
c. In the Management password field, specify the password of the
management user.
d. In the Management port field, specify the management port. By default, the
port is 3009.

Note

The NetWorker Data Domain Boost Integration Guide provides information about
the Cloud unit field and use of the Cloud tier device.

5. If required, in the Configuration pane, update the export path. It is

recommended that you leave this field blank, which sets the export path to the
default path. The short name of the NetWorker server is the default path.
If you do type a path in this field, ensure that the path has NFS permissions.
When you log in to the Data Domain resource, browse to the NFS section and
add the Mtree device path (the path to the NetWorker backup device) as a
valid NFS path.
6. To save the changes, click OK.

Entering management credentials for the Data Domain resource (instant recovery and User mode file-level restore only) 131
Recover virtual machines and data

File-level restore as a domain user

To perform a file-level restore as a domain user in the NMC NetWorker
Administration window's Recovery wizard or the Dell EMC Data Protection
Restore Client, you need to register a tenant user and provide the FLR Domain user
permissions by performing the following steps.

Note

Steps 1 through 3 provide high level information for running authc_config. More
detailed steps might be required if configuring AD authentication in the NetWorker
environment. The NetWorker Security Configuration Guide provides more information.

Procedure
1. Create a tenant user on NetWorker by running the authc_config command.
For example, open a command prompt and cd to C:\Users\Administrator,
and then type authc_config -u administrator -e add-tenant -D
tenant-name=FLR -D tenant-alias FLR -p password
2. Obtain the tenant ID by running the following command:

authc_config -u administrator -e find-tenant -D tenant-

name=FLR -p password
Tenant Id : 4
Tenant Name : FLR
Tenant Alias : FLR
Tenant Details:

3. Register the domain user by running the following command:

authc_config -u administrator -e add-config -D config-tenant-

id=3 -D config-name=FLRtest
-D config-server-address=ldap://10.63.60.31:389/
OU=vproxy,DC=v12nblr,DC=com -D config-domain=v12nblr
-D config-user-
dn=CN=flruser01,OU=users,OU=vproxy,DC=v12nblr,DC=com -D
config-user-dn-password=password
-D config-user-object-class=inetOrgPerson -D config-user-
search-path=OU=users -D config-user-id-attr=cn
-D config-group-search-path=OU=users -D config-group-name-
attr=cn -D config-group-object-class=group
-D config-group-member-attr=member -D config-active-
directory=y -p password

4. Launch the NetWorker Management Console.

5. In the NetWorker Management Console, click Setup to open the Setup
window.
6. Under Users and Roles in the left navigation pane, select NMC Roles. The
roles display in the right pane.
7. For the Console Application Administrator, Console Security Administrator
and Console User NMC roles, perform the following
a. From the right pane, right-click NMC role and select Properties.

132 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

b. In the Edit NMC Role dialog, add the Domain FLR user by typing
cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com in the External
roles field, and then click OK.
Figure 39 Add Domain FLR user

8. Navigate to the NMC Enterprise window, right-click the server and select
Launch Application... to open the NMC Administration window.
9. Click Server to open the Server window.
10. In the left navigation pane, select User Groups to display the users in the right
pane.
11. Type the Domain FLR user details in the External Roles field for the following
User groups:
l Application Administrators:
cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com
l Users: cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com
l VMware FLR Users:
cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com

12. Type the Domain FLR user details in the External Roles field for the following
User group:
l VMware FLR Users:
cn=flrusergroup,ou=users,ou=vproxy,dc=v12nblr,dc=com
In the example, the Domain FLR user
"cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com" is part of the Domain
FLR group "cn=flrusergroup,ou=users,ou=vproxy,dc=v12nblr,dc=com" in Active
Directory.

13. After registering the user as external domain, log in to the virtual machine as a
domain user.
14. Re-launch the NMC NetWorker Administration window or the Dell EMC Data
Protection Restore Client with the Domain FLR user in the following format:
l In NetWorker Administration, v12nblr\flruser01

File-level restore as a domain user 133

Recover virtual machines and data

l In the Dell EMC Data Protection Restore Client, FLR\v12nblr\flruser01

Results
You can now perform file level recovery in the NetWorker Administration Recovery
wizard or the Dell EMC Data Protection Restore Client as a domain user.

Recovering a virtual machine using the NMC Recovery wizard

When you click Recover in NMC's NetWorker Administration window and select
Recover > New from the menu, the Recovery wizard launches. Virtual Machine
Recovery is the second recovery type displayed.
Figure 40 Virtual machine recovery in the NMC Recovery wizard

After selecting the Virtual Machine Recovery type, you can perform recovery of
individual virtual machines, or (for revert and virtual machine recovery options)
recovery from multiple virtual machines.
Procedure
1. In the Select the Recovery Type page, select Virtual Machine Recovery, and
then select a vCenter server to recover from using the Source vCenter server
drop-down. Click Next.
2. In the Select the Virtual Machine to Recover page, enter the name of the
source virtual machine(s) to recover from, or perform a search for the virtual
machine. Additionally, you can use the tabs on this page to choose a single
virtual machine or multiple virtual machines from a selected backup, or browse
the source vCenter to determine the required virtual machine source. When you
locate and choose the desired virtual machine(s), click Next.

134 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 41 Select the Virtual Machine to Recover

3. In the Select the Target Backups page, select the virtual machine backup(s)
you want to restore from the Available Backups pane. This pane lists both
primary backups and, if available, clone copies. If you selected recovery from
multiple virtual machines, you can switch between virtual machines to browse
each machine's available backups by using the Virtual Machine Name drop-
down. Click Next.

Recovering a virtual machine using the NMC Recovery wizard 135

Recover virtual machines and data

Figure 42 Select the Target Backup (individual virtual machine)

Figure 43 Select the Target Backup (multiple virtual machines)

4. In the Select the Virtual Machine Recovery method page, select from one of
the available recovery options:
l Revert (or rollback) a virtual machine
l Instant Recovery of a virtual machine (direct restore from a Data Domain
device)
l Virtual Machine recovery (recovery to a new virtual machine)
l Virtual Disk recovery (recover VMDKs to an existing virtual machine)
l Emergency recovery (recovery to an ESX host)
l File Level recovery (recover files from VMDKs to a file system, or as a
download).
Figure 44 Select the Virtual Machine Recovery method

136 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Results
Subsequent wizard options change based on the recovery option selected, as
described in the following sections.

Revert (or rollback) a virtual machine backup

The first virtual machine recovery option available in the NMC Recovery wizard is to
revert, or rollback, a virtual machine backup. With a Revert a virtual machine backup
recovery, you use an existing virtual machine to rollback the VMDKs as a virtual
machine.

Note

When you revert a virtual machine, the current virtual machine is removed in the
process. You cannot use the Revert a Virtual Machine recovery option when the
ESXi has been removed from the vCenter and then added back to the vCenter. In this
case, use the Virtual Machine recovery option instead.

To complete the Recovery wizard with the reverting a virtual machine method,
perform the following.
Procedure
1. In the Select the Virtual Machine Recovery Method page:
a. Select Revert a Virtual Machine.
b. Click Next.
The Select Options to Revert a Virtual Machine page displays
2. In the Revert Type pane of the Select Options to Revert a Virtual Machine
page:
a. Select Revert both VM configuration and data to revert both the
configuration information (such as operating system, virtual machine size)
and data for a virtual machine. When you select this revert type, the Delete
existing disk on disk configuration mismatch option appears in the Revert
Options pane to allow you to overwrite an existing disk if a configuration
mismatch occurs.
b. Select Revert VM Data Only to revert only the virtual machine data without
changing the virtual machine configuration.
3. In the Revert Options pane of the Select Options to Revert a Virtual
Machine page, choose from the following options
a. Select Revert all disks on this virtual machine to rollback all VMDKs, or
select Revert one or more disks only and then select a specific disk drive to
rollback only that disk.
b. Select the Power on virtual machine checkbox to power on the virtual
machine after the restore.
c. Select Delete existing disk on disk configuration mismatch if you want to
be presented with the option of deleting the existing disk if a disk
configuration mismatch is detected. Note that this option only appears when
you select the Revert both VM configuration and data revert type in step
two.
d. Click Next.

Recovering a virtual machine using the NMC Recovery wizard 137

Recover virtual machines and data

Note

If the virtual machine is currently powered on, a dialog displays requesting

confirmation to power off the virtual machine. Additionally, if a change has
occurred in the virtual machine configuration since the backup, a warning
message displays.

Figure 45 Choose Disks to Revert

Note

The entire VMDK will be rolled back unless you have CBT enabled, in which case
only the changed blocks will be moved.

4. In the Select Alternate Recovery Sources page:

a. Select the original backup or a clone copy if one is available.
b. If recovering from a clone that is not on a Data Domain device, or recovering
from a Data Domain Cloud Tier device, specify the DD Boost clone pool.
c. Click Next.

138 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 46 Select Alternate Recovery Sources

5. In the Perform the Recovery page:

a. Specify a name for the recovery and check the summary at the bottom of
the page to ensure all the details are correct.
b. Click Run Recovery.
Results
The Check the Recovery Results page will display the duration of the recovery, and a
log file entry when the reversion is complete.

Instant Recovery of a virtual machine

The next virtual machine recovery option available in the NMC Recovery wizard is
instant recovery of a virtual machine backup. With instant recovery, the virtual
machine backup is read directly from the Data Domain device and the VMDKs will be
restored directly on a Data Domain device. You can perform one instant recovery
session at a time.
Before you begin
Before you begin, make note of the following:
l For the Data Domain resource, ensure that you provide the management
credentials and, if required, enter the export path appropriately.
l Ensure that the free space on the Data Domain system is equal to or greater than
the total disk size of the virtual machine being restored, as the restore does not
take into account the actual space required after deduplication occurs. If there is
insufficient disk space, an error appears indicating "Insufficient disk space on
datastore," and creation of the target virtual machine fails.
l Ensure that you have at least one proxy that is not restricted to a specific
datastore. For the vProxy, select Properties and then select Configuration, and
verify that datastores is left blank.
l Do not perform an instant recovery of virtual machines in resource pools and other
similar containers that are part of a currently running protection group.
To complete the Recovery wizard with the instant recovery method, perform the
following steps:

Recovering a virtual machine using the NMC Recovery wizard 139

Recover virtual machines and data

Procedure
1. In the Select the Virtual Machine Recovery Method page:
a. Select Instant Recovery.
b. Click Next.
2. In the Configure the Instant Recovery Options page:
a. Select the location where you want to restore the virtual machine in the
vCenter environment.
This does not have to be the original location, and can also be on a different
vCenter server.

b. Ensure that you select the Power on virtual machine and Reconnect to
network options.
c. Click Next.
Figure 47 Configure the Instant Recovery

3. In the Select Alternate Recovery Sources page:

a. Select the original backup, or a clone copy if one is available.
b. If recovering from a clone that is not on a Data Domain device, or recovering
from a Data Domain Cloud Tier device, specify the DD Boost clone pool.
c. Click Next.
4. In the Perform the Recovery page:
a. Specify a name for the recovery.
b. Check the summary at the bottom of the page to ensure all the details are
correct.
c. Click Run Recovery.
Results
The Check the Recovery Results page will display the duration of the recovery, and a
log file entry when the instant recovery is complete. When the instant recovery is
complete and ready for use, you can then storage vMotion the virtual machine to a
datastore, or perform a file level recovery to the target file system, and then stop the
completed instant recovery to free up those resources.
To stop an instant recovery in NMC:

140 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

1. Navigate to the Recover window.

2. Right-click the entry for the recovery within the Recover sessions pane.
3. Select Stop from the drop-down.

Note

To optimize use of NetWorker and Data Domain resources, it is strongly recommended

that you stop the instant recovery session once you satisfy your recovery objectives.

Virtual machine recovery

The next virtual machine recovery option available in the NMC Recovery wizard is to
perform a recovery of a virtual machine backed up with the vProxy Appliance to a new
virtual machine.

Note

Recoveries of virtual machines backed up with the VMware Backup Appliance should
still be performed with the EMC Backup and Recovery user interface in the vSphere
Web Client.

To complete the Recovery wizard with the virtual machine recovery method, perform
the following.
Procedure
1. In the Select the Virtual Machine Recovery Method page:
a. Select Virtual Machine Recovery.
b. Click Next.
2. In the Configure the Virtual Machine Recovery page, select the location
where you want to restore the virtual machine in the vCenter environment
a. In the Destination pane, select the option to recover the new virtual
machine to the original location, or browse to select a new location on the
same vCenter server or a different vCenter server.
b. In the Recovery Options pane, choose a vProxy for the virtual machine
recovery from the Select vProxy drop-down, specify the name of the new
virtual machine, and then optionally select the virtual machine file datastore
and folder where you want to recover the files. You can recover the virtual
machine to a Blue folder by using the VM Folder drop-down, as shown in the
following figure. The folder can be the default folder, or a new folder.

Recovering a virtual machine using the NMC Recovery wizard 141

Recover virtual machines and data

Figure 48 Configure the virtual machine recovery

If you have a single disks, or multiple disks with multiple datastores, you can
perform the following:
l Choose to recover a collection of all the available hard drives.
l Select a different datastore than the original datastore.
l Select a different datatore for each disk you want to recover.
l Specify the datastore where the virtual machine configuration files reside.
Optionally, select the Power on virtual machine and Reconnect to network
options to power on and reconnect after the recovery, and then click Next.

3. In the Select Alternate Recovery Sources page:

a. Select the original virtual machine backup, or a clone copy if one is available.
b. If recovering from a clone that is not on a Data Domain device, or recovering
from a Data Domain Cloud Tier device, specify the staging pool.
c. Click Next.

Note

If selecting a clone from Select Alternate Recovery Sources, additionally

review the "Selecting alternate recovery sources" section.

4. In the Perform the Recovery page:

a. Specify a name for the recovery and check the summary at the bottom of
the page to ensure all the details are correct.
b. Click Run Recovery.

142 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Results
The Check the Recovery Results page will display the duration of the recovery, and a
log file entry when the virtual machine recovery is complete.

Virtual Disk Recovery

The next virtual machine recovery option available in the NMC Recovery wizard is to
perform a virtual disk, or VMDK, recovery. With VMDK recovery, the disks from the
virtual machine backup are recovered to an existing virtual machine.
To complete the Recovery wizard with the virtual disk recovery method, perform the
following.
Procedure
1. In the Select the Virtual Machine Recovery Method page:
a. Select Virtual Disk Recovery.
b. Click Next.
2. In the Configure the Virtual Disk Recovery page:
a. Select the virtual machine where you want to restore the VMDKs. This can
be the original virtual machine, or another existing virtual machine.
b. Select the desired disks from the Recovery Data pane, and select a
datastore.
c. Click Next.
Figure 49 Configure the Virtual Disk Recovery

3. In the Select Alternate Recovery Sources page:

a. Select the original virtual disk backup, or a clone copy if one is available.
b. If recovering from a clone that is not on a Data Domain device, or recovering
from a Data Domain Cloud Tier device, specify the staging pool.

Recovering a virtual machine using the NMC Recovery wizard 143

Recover virtual machines and data

c. Click Next.
4. In the Perform the Recovery page:
a. Specify a name for the recovery.
b. Check the summary at the bottom of the page to ensure all the details are
correct.
c. Click Run Recovery.
Results
The Check the Recovery Results page will display the duration of the recovery, and a
log file entry when the disk recovery is complete.

Note

When you start a VMDK recovery, the virtual machine will be powered off
automatically without issuing a warning message.

Emergency Recovery
The next virtual machine recovery option available in the NMC Recovery wizard is an
Emergency Recovery. An Emergency Recovery is required when you need to restore
the virtual machine to an ESXi host.
Before you begin
Emergency Recovery requires a vProxy set up on the ESXi host prior to running the
recovery.
Additionally, ensure that you disconnect the ESXi host from the vCenter server.

Note

During an Emergency Recovery, the vProxy gets associated with the ESXi host and is
unavailable for other operations on the vCenter server. Wait until the recovery
completes before initiating any other operations on the vProxy.

To complete the Recovery wizard with the Emergency Recovery method, perform the
following:
Procedure
1. In the Select the Virtual Machine Recovery Method page:
a. Select Emergency Recovery.
b. Click Next.
2. In the Configure the Emergency Recovery page:
a. Specify the target ESXi server in the vCenter environment.
b. Click Connect.

144 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 50 Configure the Emergency Recovery

The Proxy Selection and Recovery Data panes get populated with the ESXi
server details.
3. In the Proxy Selection pane, if a proxy is not discovered, add a new proxy
which is deployed in vCenter but not added to NetWorker.
4. For the disks in the Recovery Data pane:
a. Select a datastore.
b. Optionally, select the Power on virtual machine and Reconnect to
network options.
c. Click Next.
5. In the Select Alternate Recovery Sources page:
a. Select the original disk backup, or a clone copy if one is available.
b. If recovering from a clone that is not on a Data Domain device, or recovering
from a Data Domain Cloud Tier device, specify the staging pool.
6. In the Perform the Recovery page:
a. Specify a name for the recovery and check the summary at the bottom of
the page to ensure all the details are correct.
b. Click Run Recovery.
Results
The Check the Recovery Results page will display a progress bar with the duration of
the recovery, and a log file entry when the Emergency Recovery is complete.

Note

The progress bar may not update correctly when you perform an Emergency Recovery
directly to the ESXi host.

Recovering a virtual machine using the NMC Recovery wizard 145

Recover virtual machines and data

File Level recovery (Admin mode only)

The final virtual machine recovery option available in the NMC Recovery wizard is File
Level recovery. With file level recovery, you can recover individual files from backups
of virtual machines or VMDKs to a primary or secondary vCenter server, and for
application-consistent backups, you can also restore the transaction log from Data
Domain to the SQL database.
Before you begin
NetWorker only supports file level recovery operations from a primary or cloned
backup if the save set is on a Data Domain device. If a cloned backup does not exist on
the Data Domain device, you must manually clone a save set from the tape device to
Data Domain before launching the Recovery wizard.
For the Data Domain resource, ensure that you provide the management credentials
and, if required, type the export path appropriately. The section Entering management
credentials for the Data Domain resource (instant recovery and User mode file-level
restore only) provides detailed steps.
Additionally, if recovering to a virtual machine on a secondary vCenter, ensure that a
vProxy appliance has been deployed on the secondary vCenter server and configured
with the NetWorker server.
File level recovery in the NMC Recovery wizard can only be performed by an
administrator.

Note

For file-level recovery of high-density file systems (more than few hundred files/
folders), it is recommended to use either the NetWorker Management Web UI or the
Dell EMC Data Protection Restore Client (User or Admin mode, as applicable)
instead of the NMC Recovery wizard.

To complete the Recovery wizard with the file level recovery method, perform the
following:
Procedure
1. In the Select the Virtual Machine Recovery Method page:
a. Select File Level recovery.
b. Click Next.
2. In the Select Alternate Recovery Sources page:
a. Select the primary backup to recover from, or select the Recover the
Virtual machine from a clone on a Data Domain device option.
b. Select the clone copy that you want to recover files from.
c. Click Next.

Note

If selecting a clone from Select Alternate Recovery Sources, additionally

review the section "Selecting alternate recovery sources".

146 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 51 Select Alternate Recovery Sources for file level recovery

3. In the Select the target Virtual Machine page:

a. Select the virtual machine that you want to recover the files to.
By default, the virtual machine that you selected for recovery in the Select
the Virtual Machine to Recover page is displayed.

b. To recover to another virtual machine in the vCenter, or recover to a virtual

machine on a secondary vCenter, select Browse the vCenter server to
select a Virtual Machine to recover to, and choose a vCenter from the
drop-down to browse that vCenter's tree and select a different virtual
machine.
c. Click Next.

Note

Cross-platform recovery, for example from a Windows to a Linux virtual

machine, is not supported.

4. In the Mount The Saveset page:

a. Provide the username and password of the virtual machine where the files
will be restored to.
b. Click Start Mount.
c. If performing file level recovery as a domain user, provide the AD user details
—no operating system or local account is required if you have configured
the AD/domain user.

Recovering a virtual machine using the NMC Recovery wizard 147

Recover virtual machines and data

Figure 52 Mount the save set for file level recovery

When the Mount Results pane shows that the mount has succeeded, click
Next.

Note

This user should have privileges to install the FLR Agent, which is required to
perform file level recovery. For Linux virtual machines, this requires the root
user account.

5. In the Select the Files and Folders to Recover page:

a. Browse through the folder structure to select the files you want to recover.
b. Click Next.

148 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 53 Select the files and folders to recover

6. In the Select the Restore Location page:

a. Select the folder that you want to recover the files to, or create a folder.
b. Click Next.

Note

NetWorker does not currently support creating folders with spaces in the folder
name.

7. In the Perform the Recovery page:

a. Specify a name for the recovery.
b. To ensure all the details are correct, check the summary at the bottom of
the page
c. Click Run Recovery.

Results
The Check the Recovery Results page displays the duration of the recovery, and a
log file entry when the file level recovery is complete.

Selecting alternate recovery sources in the NMC Recovery wizard

The NMC Recovery wizard contains a step for each virtual machine recovery method
where you can select an alternate source to recover from, for example, a clone copy
on a Data Domain or non-Data Domain device. If the primary source is present, it is
recommended that you recover from the primary source. However, if both the primary
source and clone copies are present and enabled and you want to recover from a clone
copy, perform the following.

Recovering a virtual machine using the NMC Recovery wizard 149

Recover virtual machines and data

Procedure
1. In the Select Alternative Recovery Sources page, select the clone you want to
recover from, either a clone on a Data Domain device or non-Data Domain
device.
Additionally, make note of the name indicated in the Volume column for all of
the volumes you do not want to recover from, as you will require this
information in steps 5 and 6.
2. Click Close to display the Save Progress dialog, and then specify a name for
the recover and click Save to save your progress.
3. In the NMC Administration window, click Devices to display the Devices
window.
4. In the left navigation pane, select Devices. The list of devices displays in the
right pane.
5. For each volume you do not want to recover from that you made note of in step
1, locate the corresponding device, and make note of that device name.
6. For each device you identify as corresponding with those volumes, right-click
the device and select Unmount from the drop-down, and then also select
Disable from the drop-down.

Note

Ensure that no backups are currently running to these devices prior to

unmounting.

7. In the NMC Administration window, click Recover to display the Recover

window, and locate the saved recovery
8. Right-click the saved recovery and select Open Recover.
The Recovery wizard re-opens on the Select Alternative Recovery Sources
page.
9. In the Recovery Source pane of the Select Alternative Recovery Sources
page, select either Recover the virtual machine from a clone on a Data
Domain device, or Recover the virtual machine from a clone on a non-Data
Domain device. Click Next.

Note

If you want to recover from a clone on a non-Data Domain device, manually

change the staging pool to a different pool, and ensure that your selected pool
does not already contain copies for this backup. If the primary source is present
and you select a clone to recover from using the same staging pool that
contains the existing copy, the recovery may become unresponsive.

10. In the Perform the Recovery page, specify a name for the recovery and check
the summary at the bottom of the page to ensure all the details are correct.
Click Run Recovery.
The Check the Recovery Results page will display the duration of the
recovery, and a log file entry when the recovery is complete.
11. In the NMC Administration window, click Devices to return to the Devices
window, and in the left navigation pane, select Devices to display the list of
devices in the right pane.

150 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

12. For each device that you unmounted and disabled in step 6, right-click the
device and select Enable from the drop-down, and then select Mount from the
drop-down.

Monitoring and verifying Virtual Machine recoveries

After selecting Run Recovery to complete the Recovery wizard, there are multiple
ways you can monitor the progress of the virtual machine recovery, and then verify
when the recovery is complete.
NMC Recover and Monitoring windows
To monitor the progress of the virtual machine recovery, use the Recover sessions
pane in the Monitoring window, or the Currently Running pane of the Recover
window.
To verify that the virtual machine recovery is complete, use the Configured Recovers
pane in the Recover window.
Check the Recovery results in the NMC Recovery wizard
The final step of the Recovery wizard also allows you to check the recovery results.
Upon completion of the virtual machine recovery, an entry for the log file appears in
the Recovery log pane. Click Export log to save and view the log file.
Recovery configuration information storage
When you create a recover configuration by using the Recovery wizard, NetWorker
saves the configuration information in an NSR recover resource in the resource
database of the NetWorker server. NetWorker uses the information in the NSR
recover resource to perform the recover job operation.
When a recover job operation starts, NetWorker stores:
l Details about the job in the nsrjobsd database.
l Output sent to stderr and stdout in a recover log file. NetWorker creates one log
file for each recover job.

NOTICE

NetWorker removes the recover log file and the job information from the job
database based on value of the Jobsdb retention in hours attribute in the
properties of the NetWorker server resource. The default jobsdb retention is 72
hours.

vProxy recovery in the NetWorker Management Web UI

The NetWorker Management Web UI contains the same vProxy recovery functionality
that is available in the NetWorker Management Console through the Recovery
wizard, including support for all image-level recovery types and file-level recovery.
When logged in to the NetWorker Management Web UI, the landing page displays
options for Monitoring, Protection, and Recovery in the left pane. If not already
selected, select Recover, and then select VMware Recovery.
In the VMware Recovery window's Select vCenter drop-down, choose the vCenter
server that contains the virtual machines or objects that you want to recover. Then,
select List and Search to view only the available virtual machine backups, or Browse
vCenter to navigate to the location within the vCenter that contains the virtual
machine or objects that you want to recover. When you select an item, the backup
details display in a table within the right pane. You can choose to display hidden

vProxy recovery in the NetWorker Management Web UI 151

Recover virtual machines and data

columns such as the virtual machine UUID by clicking the blue icon in the lower left
corner of the table.
From the Backups and Clones pane, select from one of the available primary or
cloned backups, and then select the Recovery drop-down to choose from one of the
image-level recovery types available, or file level recovery. Additionally, ensure that
you specify the correct time range of the backup(s) that you want to recover.

Revert (or rollback) a virtual machine backup

Select Revert to rollback one or more virtual machine disks (VMDKs) as a virtual
machine to the original virtual machine. Additionally, you can rollback the virtual
machine configuration.

Note

You cannot use the Revert recovery type when the ESXi has been removed from the
vCenter and then added back to the vCenter. In this case, use the Virtual Machine
recovery method instead.

Procedure
1. In the VMware Recovery window's Backups and Clones pane, select from one
of the available primary or cloned backups, and then select the Recovery drop-
down.
2. From the Image Level drop-down, select Revert.
The Recover wizard launches.
3. In the Configuration page:
a. From the Proxy drop-down, select Automatic to use the default vProxy
appliance, or choose another vProxy.
b. Select Power On to power on the virtual machine after the recovery
completes.

Note

If the virtual machine is currently powered on, a dialog displays requesting

confirmation to power off the virtual machine. Additionally, if a change has
occurred in the virtual machine configuration since the backup, a warning
message will display on the Summary page.

c. Select Revert VM configuration to restore the virtual machine with the

same configuration details used at the time of backup. Additionally, select
the Delete existing disk on config mismatch option if you want to continue
with the removal of the existing disk if the configuration details do not
match. If you do not select Revert VM configuration, the recovery will
revert only the virtual machine data without changing the virtual machine
configuration.
d. If required, set a Debug level if you want to enable debug logs. The default
level is 0.
e. Click Next.
The Disk Selection page displays
4. In the Disk Selection page, choose one or more of the available hard disks, and
then click Next.

152 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Note

The entire VMDK will be rolled back unless you have CBT enabled, in which case
only the changed blocks will be moved.

The Summary page displays.

5. In the Summary page, review the recovery details and then click Finish.
Results
The wizard exits and a message displays along the top of the VMware Recovery
window to indicate that a recovery request was submitted. Select Monitoring in the
left pane to view the duration and status of the recovery operation.

Recover to a new virtual machine

Select New Virtual Machine to recover a virtual machine backed up with the vProxy
appliance to a new virtual machine.
Procedure
1. In the VMware Recovery window's Backups and Clones pane, select from one
of the available primary or cloned backups, and then select the Recovery drop-
down.
2. From the Image Level drop-down, select New Virtual Machine.
The Recover wizard launches.
3. In the Configuration page:
a. From the Destination vCenter drop-down, select a different destination
vCenter server if required, or leave the default selection of the same
vCenter server.
b. From the Proxy drop-down, select Automatic to use the default vProxy
appliance, or choose another vProxy.
c. In the Virtual Machine Name field, specify the name of the new virtual
machine.
d. Select Power On to power on the virtual machine after the recovery
completes.
e. Select Reconnect NIC to reconnect the network interface card after the
recovery completes.
f. If required, set a Debug level if you want to enable debug logs. The default
level is 0.
g. Click Next.
The Destination Location page displays.
4. In the Destination Location page, select the location where you want to
recover the virtual machine. If the target location contains a specific folder that
you need to select, select the desired folder from the VM Folder drop-down.
Click Next.
The Disk Selection page displays.
5. In the Disk Selection page, choose one or more of the available hard disks, and
select a Destination Datastore for each selected disk. The default Destination
Datastore selected is the original datastore, however, you can select a different
datastore for each disk you want to recover. Additionally, you can use the VM

Recover to a new virtual machine 153

Recover virtual machines and data

Configuration Files drop-down to select the datastore where the virtual

machine configuration files will reside. Click Next.

Note

The entire VMDK will be rolled back unless you have CBT enabled, in which case
only the changed blocks will be moved.

The Summary page displays.

6. In the Summary page, review the recovery details and then click Finish.
Results
The wizard exits and a message displays along the top of the VMware Recovery
window to indicate that a recovery request was submitted. Select Monitoring in the
left pane to view the duration and status of the recovery operation.

Instant Restore of a virtual machine

When you select Instant Restore, the virtual machine backup is read directly from the
Data Domain device and the VMDKs will be restored directly on a Data Domain device.
You can perform one instant recovery session at a time.
Before you begin
Before you begin, make note of the following:
l For the Data Domain resource, ensure that you provide the management
credentials and, if required, enter the export path appropriately.
l Ensure that the free space on the Data Domain system is equal to or greater than
the total disk size of the virtual machine being restored, as the restore does not
take into account the actual space required after deduplication occurs. If there is
insufficient disk space, an error appears indicating "Insufficient disk space on
datastore," and creation of the target virtual machine fails.
l Ensure that you have at least one proxy that is not restricted to a specific
datastore. For the vProxy, select Properties and then select Configuration, and
verify that datastores is left blank.
l Do not perform an instant recovery of virtual machines in resource pools and other
similar containers that are part of a currently running protection group.
Procedure
1. In the VMware Recovery window's Backups and Clones pane, select from one
of the available primary or cloned backups, and then select the Recovery drop-
down.
2. From the Image Level drop-down, select Instant Restore.
The Recover wizard launches.
3. In the Configuration page:
a. From the Destination vCenter drop-down, select a different destination
vCenter server if required, or leave the default selection of the same
vCenter server.
b. From the Proxy drop-down, select Automatic to use the default vProxy
appliance, or choose another vProxy.
c. In the Virtual Machine Name field, specify the name of the new virtual
machine.

154 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

d. Select Power On to power on the virtual machine after the recovery

completes.
e. Select Reconnect NIC to reconnect the network interface card after the
recovery completes.
f. If required, set a Debug level if you want to enable debug logs. The default
level is 0.
g. Click Next.
The Destination Location page displays.
4. In the Destination Location page, select the location in the vCenter server
where you want to recover the virtual machine, and then click Next.
The Summary page displays.
5. In the Summary page, review the recovery details and then click Finish.
Results
The wizard exits and a message displays along the top of the VMware Recovery
window to indicate that a recovery request was submitted. Select Monitoring in the
left pane to view the duration and status of the recovery operation.
Note that the status might not update to "Completed" or "Succeeded" upon a
successful instant recovery. If this occurs, cancel the corresponding NetWorker
restore task in the vSphere Client and the status will update correctly in the
NetWorker Management Web UI.

Note

To optimize use of NetWorker and Data Domain resources, it is strongly recommended

that you stop the instant recovery session once you satisfy your recovery objectives.

Virtual Disk (VMDK) recovery

Select Virtual Disk to recover the disks from the virtual machine backup to an existing
virtual machine.
Procedure
1. In the VMware Recovery window's Backups and Clones pane, select from one
of the available primary or cloned backups, and then select the Recovery drop-
down.
2. From the Image Level drop-down, select Virtual Disk.
The Recover wizard launches.
3. In the Configuration page:
a. From the Destination vCenter drop-down, select a different destination
vCenter server if required, or leave the default selection of the same
vCenter server.
b. From the Proxy drop-down, select Automatic to use the default vProxy
appliance, or choose another vProxy.
c. Select Power On to power on the virtual machine after the recovery
completes.
d. If required, set a Debug level if you want to enable debug logs. The default
level is 0.

Virtual Disk (VMDK) recovery 155

Recover virtual machines and data

e. Click Next.
The Virtual Machine Selection page displays.
4. In the Virtual Machine Selection page, select the location of the virtual
machine in the vCenter server where you want to recover the virtual disk(s),
and then click Next.

Note

This location can be the original virtual machine, or another existing virtual
machine.

The Disk Selection page displays.

5. In the Disk Selection page, choose one or more of the available hard disks, and
select a Destination Datastore for each selected disk. The default Destination
Datastore selected is the original datastore, however, you can select a different
datastore for each disk you want to recover. Click Next.
The Summary page displays.
6. In the Summary page, review the recovery details and then click Finish.
Results
The wizard exits and a message displays along the top of the VMware Recovery
window to indicate that a recovery request was submitted. Select Monitoring in the
left pane to view the duration and status of the recovery operation.

Note

When you start a Virtual Disk recovery, the virtual machine will be powered off
automatically without issuing a warning message.

Emergency Recovery
Select Emergency when you need to restore the virtual machine to an ESXi host.
Before you begin
Emergency recovery requires a vProxy set up on the ESXi host prior to running the
recovery.
Additionally, ensure that you disconnect the ESXi host from the vCenter server.

Note

During an Emergency Recovery, the vProxy gets associated with the ESXi host and is
unavailable for other operations on the vCenter server. Wait until the recovery
completes before initiating any other operations on the vProxy.

To complete the Recovery wizard with the Emergency Recovery method, perform the
following:
Procedure
1. In the VMware Recovery window's Backups and Clones pane, select from one
of the available primary or cloned backups, and then select the Recovery drop-
down.
2. From the Image Level drop-down, select Emergency.
The Recover wizard launches.

156 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

3. In the Configuration page:

a. From the ESX Server drop-down, select the IP of the ESX server in the
vCenter environment where you want to restore the virtual machine backup.
b. Specify the root Username and Password for the ESX Server.
c. In the Virtual Machine Name field, specify the name of the new virtual
machine.
d. Select Power On to power on the virtual machine after the recovery
completes.

Note

If the virtual machine is currently powered on, a dialog displays requesting

confirmation to power off the virtual machine. Additionally, if a change has
occurred in the virtual machine configuration since the backup, a warning
message displays.

e. Select Reconnect NIC to reconnect the network interface card after the
recovery completes.
f. If required, set a Debug level if you want to enable debug logs. The default
level is 0.
g. Click Next.
The VMware Proxy Configuration page displays.
4. In the VMware Proxy Configuration page:
a. For Proxy Selection Type, if the desired proxy has been discovered, select
an existing vProxy for the recovery. Alternatively, you can use a new vProxy
that is deployed in the vCenter but not yet added in NetWorker by selecting
Register a new VMware Proxy.
b. From the Select Proxy drop-down, select one of the registered vProxies.
c. Click Next.
The Disk Selection page displays.
5. In the Disk Selection page, choose one or more of the available hard disks, and
select a Destination Datastore for each selected disk. The default Destination
Datastore selected is the original datastore, however, you can select a different
datastore for each disk you want to recover. Additionally, you can use the VM
Configuration Files drop-down to select the datastore where the virtual
machine configuration files will reside. Click Next.
The Summary page displays.
6. In the Summary page, review the recovery details and then click Finish.

Results
The wizard exits and a message displays along the top of the VMware Recovery
window to indicate that a recovery request was submitted. Select Monitoring in the
left pane to view the duration and status of the recovery operation.

Note

The progress bar may not update correctly when you perform an Emergency Recovery
directly to the ESXi host.

Emergency Recovery 157

Recover virtual machines and data

File Level recovery

Select File Level to recover individual files from backups of virtual machines or
VMDKs to a primary or secondary vCenter server.
Before you begin
NetWorker only supports file level recovery operations from a primary or cloned
backup if the save set is on a Data Domain device. If a cloned backup does not exist on
the Data Domain device, you must manually clone this save set to Data Domain before
launching the Recovery wizard.
For the Data Domain resource, ensure that you provide the management credentials
and, if required, type the export path appropriately. The section Entering management
credentials for the Data Domain resource (instant recovery and User mode file-level
restore only) provides detailed steps.
Additionally, if recovering to a virtual machine on a secondary vCenter, ensure that a
vProxy appliance has been deployed on the secondary vCenter server and configured
with the NetWorker server.

Note

File level recovery in the NetWorker Management Web UI can only be performed by
an administrator.

Procedure
1. In the VMware Recovery window's Backups and Clones pane, select from one
of the available primary or cloned backups, and then select the Recovery drop-
down.
2. Select File Level.
The Recover wizard launches.
3. In the Configuration page:
a. From the Destination vCenter drop-down, select a different destination
vCenter server if required, or leave the default selection of the same
vCenter server.
b. From the Proxy drop-down, select Automatic to use the default vProxy
appliance, or choose another vProxy.
c. Select Overwrite to overwrite files in the destination location that have the
same name as files being recovered.
d. Select Terminate mount session to release the disk mount after the
recovery completes.
e. If required, set a Debug level if you want to enable debug logs. The default
level is 0.
f. Click Next.
The Destination Virtual Machine page displays.
4. In the Destination Virtual Machine page, the location of the original virtual
machine backup displays by default in blue. If you do not want to recover to the
original location, navigate to the desired virtual machine in the vCenter server
where you want to recover the objects, and click Next.
The Mount Configuration page displays.

158 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

5. In the Mount Configuration page, type the user credentials to access the
virtual machine that you want to recover objects to in order to initiate the disk
mount. This user should have privileges to install the FLR Agent, which is
required to perform file level recovery. For Linux virtual machines, this requires
the root user account. Optionally, select Keep FLR agent after installation if
you do not want to remove the FLR Agent from the virtual machine upon
recovery completion. Click Mount.
The disk mount initializes and a progress bar displays.

Note

You cannot browse the contents of the virtual machine backup until the
mounting of the destination virtual machine completes successfully.
6. When the mount completes successfully, click Next.
The Source Data page displays.
7. In the Source Data page, select individual folders to browse the contents of the
backup, and select the objects you want to recover. You can select all objects in
a folder by clicking the checkbox to the left of the Name field in the Contents
pane.
When any objects in a folder are selected, that folder is highlighted in blue in the
Folders pane. After selecting the objects that you want to recover, click Next.
The Destination Location page displays.
8. In the Destination Location page, browse the folder structure of the
destination virtual machine to select the folder where you want to recover the
objects. Click Next.
The Summary page displays.
9. In the Summary page, review the recovery details and then click Finish.
Results
The wizard exits and a message displays along the top of the VMware Recovery
window to indicate that a recovery request was submitted. Select Monitoring in the
left pane to view the duration and status of the recovery operation.

Monitor recovery operations in the NetWorker Management Web UI

After initiating a recovery operation in the NetWorker Management Web UI, select
Monitoring in the left pane to view the status and progress of the recovery in the
right pane.
In addition to the progress and completion status of individual recovery operations, a
column displays the recovery type. You can choose to display hidden columns by
clicking the blue icon in the lower left corner of the table.
If you need to troubleshoot recovery operations, you can view the vProxy logs by
clicking the menu in the first column and selecting View Messages from the drop-
down.

vProxy file-level restore and SQL restore in the Dell EMC

Data Protection Restore Client
You can also use the Dell EMC Data Protection Restore Client to perform granular
recovery from a primary or cloned vProxy backup on a Data Domain device. The Dell

Monitor recovery operations in the NetWorker Management Web UI 159

Recover virtual machines and data

EMC Data Protection Restore Client allows you to restore specific files and folders
from virtual machines in User and Admin modes, and also restore individual SQL
databases from SQL server application-aware backups. The Dell EMC Data
Protection Restore Client is part of the NetWorker client installation.

Note

Before you start a file-level restore, review the prerequisites in the section File-level
restore prerequisites, as well as File-level restore and SQL restore limitations to
ensure that you can perform file-level restores in your configuration.

Pre-requisites for file-level restore and SQL restore

Review the following information before performing a file-level restore or SQL restore
in the Dell EMC Data Protection Restore Client.

File-level restore and SQL database/instance level restore only supported from primary or clone
backup on a Data Domain device
NetWorker only supports file-level restore and SQL database/instance level restore
operations from a primary or cloned backup when the save set is on a Data Domain
device.
If a cloned backup does not exist on the Data Domain device, you must manually clone
a save set from the tape device to Data Domain before launching the Dell EMC Data
Protection Restore Client.
If backups reside on a non-Data Domain Device such as Cloud Boost, tape, Cloud Tier,
or AFTD, the backups do not display in the Dell EMC Data Protection Restore
Client. In this case, use NMC to identify and clone the save sets back to the Data
Domain device.

Supported platform versions

The Dell EMC Data Protection Restore Client supports file-level restore for the
following platforms and operating system versions:
l RedHat Enterprise Linux versions 6.x and 7.x
l SuSE Linux Enterprise Server versions 11.x and 12.x
l Debian version 9.1
l Ubuntu version 17.10
l CentOS version 7.2
l OEL version 7.2
l Windows 64-bit platforms

Supported browser versions

Use of the Dell EMC Data Protection Restore Client may require upgrading your
browser to the latest version.
For example, the Dell EMC Data Protection Restore Client does not work on Mozilla
FireFox unless you install a minimum version of 43.0.3.
If you notice an error when logging in to the Dell EMC Data Protection Restore
Client or are unable to login, ensure your browser is up-to-date and then retry the
login.

160 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Support for Debian or Ubuntu operating system

vProxy file-level restore is supported on the Debian/Ubuntu operating system. To
configure the Debian or Ubuntu guest operating system for file-level restore, perform
the following steps.

Note

File-level restore is not supported on Debian/Ubuntu ext4 file systems.

Procedure
1. Log in to the system console as a non-root user.
2. Run the sudo passwd root command.
Enter the new password twice to set a password for the root account.
3. Run the sudo passwd -u root command to unlock the root account.
4. Specify the root user credentials in the Dell EMC Data Protection Restore
Client and proceed to complete the file-level restore operation at least once.
While performing the file-level restore operation for the first time, remember to
select Keep FLR agent.
5. After performing the above steps at least once, you can revert the root account
to the locked state and use non-root account for future file-level restore
requests. Non-root user can lock the root account with the sudo passwd -l
root command.

NetWorker privileges required by File-level restore and SQL database/instance level restore
users
A new user group, VMware FLR Users, requires NetWorker privileges for User and
Admin logins to perform file-level restore and SQL database/instance level restore
operations in the Dell EMC Data Protection Restore Client.
Specify the following privileges for the VMware FLR Users group by using the NMC
NetWorker Administration window or nsradmin.

Table 14 FLR privilege requirements

User Admin
Remote Access All Clients Remote Access All Clients

Operate NetWorker Operate NetWorker

Monitor NetWorker Monitor NetWorker

Operate Devices and Jukeboxes Operate Devices and Jukeboxes

Recover Local Data Recover Local Data

Backup Local Data Backup Local Data

View Security Settings

Operating system utilities required for file-level restore

On Linux and Windows, the installed operating system must include several standard
utilities in order to use file-level restore. Depending on the target operating system for

Pre-requisites for file-level restore and SQL restore 161

Recover virtual machines and data

restore and the types of disks or file systems in use, some of these standard utilities,
however, may not be included.
The following utilities and programs may be required for performing file-level restore.
On Windows:
l msiexec.exe
l robocopy.exe
l diskpart.exe
l cmd.exe
On Linux:
l blkid
l udevadm
l readlink
l rpm
l rsync
l bash

Note

On Linux LVM, LVM2 rpm version 2.02.117 or later is required. Also, additional binaries
required on Linux LVM include dmsetup, lvm, and vgimportclone.

Entering management credentials for the Data Domain resource (instant recovery and User
mode file-level restore only)
Before you perform an instant recovery of a virtual machine or file-level restore (User
mode), ensure that you provide the management credentials for the Data Domain
resource. For instant recovery, these credentials are required when performing the
recovery using the NMC Recover wizard or the VM Backup and Recovery interface
in the vSphere Web Client.
Procedure
1. In the NMC Administration window, click Devices.
The Devices window displays.
2. In the expanded left navigation pane, select Data Domain Systems.
3. In the right details pane, right-click the Data Domain system, and then select
Properties.
The NSR Data Domain Properties window displays.

162 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 54 NSR Data Domain Properties

4. In the Access pane, type the management credentials.

a. In the Management host field, specify the hostname of the Data Domain
system that is used for management commands.
b. In the Management user field, specify the username for a Data Domain user
that has admin access. For example, sysadmin. The Management user should
have Data Domain administrator privileges.
c. In the Management password field, specify the password of the
management user.
d. In the Management port field, specify the management port. By default, the
port is 3009.

Note

The NetWorker Data Domain Boost Integration Guide provides information about
the Cloud unit field and use of the Cloud tier device.

5. If required, in the Configuration pane, update the export path. It is

recommended that you leave this field blank, which sets the export path to the
default path. The short name of the NetWorker server is the default path.
If you do type a path in this field, ensure that the path has NFS permissions.
When you log in to the Data Domain resource, browse to the NFS section and
add the Mtree device path (the path to the NetWorker backup device) as a
valid NFS path.
6. To save the changes, click OK.

Pre-requisites for file-level restore and SQL restore 163

Recover virtual machines and data

File-level restore as a domain user

To perform a file-level restore as a domain user in the NMC NetWorker
Administration window's Recovery wizard or the Dell EMC Data Protection
Restore Client, you need to register a tenant user and provide the FLR Domain user
permissions by performing the following steps.

Note

Steps 1 through 3 provide high level information for running authc_config. More
detailed steps might be required if configuring AD authentication in the NetWorker
environment. The NetWorker Security Configuration Guide provides more information.

Procedure
1. Create a tenant user on NetWorker by running the authc_config command.
For example, open a command prompt and cd to C:\Users\Administrator,
and then type authc_config -u administrator -e add-tenant -D
tenant-name=FLR -D tenant-alias FLR -p password
2. Obtain the tenant ID by running the following command:

authc_config -u administrator -e find-tenant -D tenant-

name=FLR -p password
Tenant Id : 4
Tenant Name : FLR
Tenant Alias : FLR
Tenant Details:

3. Register the domain user by running the following command:

authc_config -u administrator -e add-config -D config-tenant-

id=3 -D config-name=FLRtest
-D config-server-address=ldap://10.63.60.31:389/
OU=vproxy,DC=v12nblr,DC=com -D config-domain=v12nblr
-D config-user-
dn=CN=flruser01,OU=users,OU=vproxy,DC=v12nblr,DC=com -D
config-user-dn-password=password
-D config-user-object-class=inetOrgPerson -D config-user-
search-path=OU=users -D config-user-id-attr=cn
-D config-group-search-path=OU=users -D config-group-name-
attr=cn -D config-group-object-class=group
-D config-group-member-attr=member -D config-active-
directory=y -p password

4. Launch the NetWorker Management Console.

5. In the NetWorker Management Console, click Setup to open the Setup
window.
6. Under Users and Roles in the left navigation pane, select NMC Roles. The
roles display in the right pane.
7. For the Console Application Administrator, Console Security Administrator
and Console User NMC roles, perform the following
a. From the right pane, right-click NMC role and select Properties.
b. In the Edit NMC Role dialog, add the Domain FLR user by typing
cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com in the External
roles field, and then click OK.

164 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 55 Add Domain FLR user

8. Navigate to the NMC Enterprise window, right-click the server and select
Launch Application... to open the NMC Administration window.
9. Click Server to open the Server window.
10. In the left navigation pane, select User Groups to display the users in the right
pane.
11. Type the Domain FLR user details in the External Roles field for the following
User groups:
l Application Administrators:
cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com
l Users: cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com
l VMware FLR Users:
cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com

12. Type the Domain FLR user details in the External Roles field for the following
User group:
l VMware FLR Users:
cn=flrusergroup,ou=users,ou=vproxy,dc=v12nblr,dc=com
In the example, the Domain FLR user
"cn=flruser01,ou=users,ou=vproxy,dc=v12nblr,dc=com" is part of the Domain
FLR group "cn=flrusergroup,ou=users,ou=vproxy,dc=v12nblr,dc=com" in Active
Directory.

13. After registering the user as external domain, log in to the virtual machine as a
domain user.
14. Re-launch the NMC NetWorker Administration window or the Dell EMC Data
Protection Restore Client with the Domain FLR user in the following format:
l In NetWorker Administration, v12nblr\flruser01
l In the Dell EMC Data Protection Restore Client, FLR\v12nblr\flruser01

Pre-requisites for file-level restore and SQL restore 165

Recover virtual machines and data

Results
You can now perform file level recovery in the NetWorker Administration Recovery
wizard or the Dell EMC Data Protection Restore Client as a domain user.

Create a user in the NetWorker authentication service (User mode file-level restore only)
When performing file-level restore in User Mode, you must create a user in the
Networker Management Console (NMC) using the Manage Authentication Service
Users option, and make note of the password as you will require this information when
logging in to the Dell EMC Data Protection Restore Client.
Before you begin
For file-level restores on Linux virtual machines, the root account credentials are
required for the target virtual machine in order to install the FLR Agent. During the
file-level restore session, if non-root credentials are provided for the target virtual
machine, the FLR Agent installation fails, even if this user has privileges similar to a
root user. To perform a file-level restore using a non-root user, ensure that the FLR
Agent has already been installed on the target virtual machine using the root user
account.
For file-level restores on Windows virtual machines, if the provided credentials for the
target virtual machine do not have administrative privileges, theFLR Agent installation
fails. To perform a file-level restore using a non-administrator user, ensure that the
FLR Agent is already installed on the target machine using administrative privileges.
Procedure
1. In the NMC NetWorker Administration window, click Server to open the
Server window.
2. In the left navigation pane, highlight User Groups, and then right-click and
select Manage Authentication Service Users.
Figure 56 Manage Authentication service users

3. In the Manage Authentication Service Users dialog box, click Add.

4. For the new user user1, provide a username, password and other details, and
then select the checkbox next to Users in the Group field and click OK.

166 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

5. Right-click Application Administrators and select Properties. In the User

Group Properties, create an entry for the user created in step 4 (for example,
user1), in the format user=user1,host=NW server FQDN.
Figure 57 Application Administrators user group properties

6. Right click VMware FLR Users and select Properties. In the User field, create
an entry for the user created in step 4 (for example, user1), in the format
user=user1,host=NW server FQDN.

Figure 58 VMware FLR Users user group properties

Results
You can now use this new user to log into the Dell EMC Data Protection Restore
Client.

Pre-requisites for file-level restore and SQL restore 167

Recover virtual machines and data

FLR Agent is required for file-level restore

The FLR Agent is required for file-level restore operations and gets installed
automatically on the target virtual machine when you initiate a file-level restore and
provide the virtual machine credentials.
The FLR Agent installation on Linux virtual machines requires that you use the root
account. If non-root credentials are provided for the target virtual machine, the FLR
Agent installation fails, even if this user has privileges similar to a root user. Once the
FLR Agent installation is completed by a root user, you can perform file-level restore
operations as a non-root user.
FLR Agent installation on Windows virtual machines requires that you use
administrative privileges. If the provided credentials for the target virtual machine do
not have administrative privileges, theFLR Agent installation fails.
If the request to install the FLR Agent was not successful and you initiate a file-level
restore, the following message appears.
Figure 59 Deploy FLR Agent if not found

This message provides an option to deploy the FLR Agent by providing the appropriate
credentials.
On Linux, to perform a file-level restore using a non-root user, ensure that the FLR
Agent has already been installed on the target virtual machine using the root user
account. Otherwise, ensure that you are using a supported platform and the root user
is specified, and click OK. For Linux, file-level restore is only supported on Red Hat
Enterprise Linux versions 6 and 7, and SuSE Linux Enterprise Server versions 11 and
12.
On Windows, to perform a file-level restore using a non-administrator user, ensure
that the FLR Agent is already installed on the target machine using administrative
privileges. Otherwise, ensure that an administrative user is specified, and click OK.
FLR Agent installation on Windows virtual machines with User Account Control
(UAC) enabled
Performing the FLR Agent installation on UAC-enabled Windows virtual machine
requires you to either provide the credentials of the administrator user, or to disable
UAC during the FLR Agent installation, and then re-enable on completion.
On Windows versions 7, 8, and 10, the administrator account is disabled by default. To
enable the account, complete the following steps:
1. To activate the account, open a command prompt in administrative mode, and
then type net user administrator /active: yes.
2. To set a password for the administrator account, go to Control Panel > User
Accounts and select the Advanced tab. Initially, the account password is blank.

168 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

3. In the User Accounts pane, right-click the user and select Properties, and then
clear the Account is disabled option.
To disable UAC during the FLR Agent installation and then re-enable on completion of
the installation, complete the following steps:
1. Log in to the Dell EMC Data Protection Restore Client as an administrator user
to initiate a request to launch the FLR Agent installation window.
2. In the FLR Agent installation window, select the Keep vProxy FLR on target
virtual machine option.
3. Open regedit and change the EnableLUA registry key value at HKLM\SOFTWARE
\Microsoft\Windows\CurrentVersion\Policies\System to
0x00000000. By default, this is set to 1.
4. Proceed with the FLR Agent installation.
5. Open regedit and reset the EnableLUA registry key to the previous value to re-
enable UAC.

File-level restore and SQL restore limitations

This section provides a list of limitations that apply to file-level restore and individual
SQL database and instance restore.
Compatibility requirements and unsupported configurations
Review the following limitations related to file-level restore compatibility requirements
and unsupported configurations.
l File-level restore and SQL instance restore in the Dell EMC Data Protection
Restore Client is only supported on the platforms and versions identified in the
section Supported platform versions. The online compatibility guide, available at
https://elabnavigator.emc.com/eln/modernHomeDataProtection, provides more
software compatibility information.
l Update your web browser to the latest version. It is recommended that you use
the Chrome or Mozilla browser for file-level restore operations.
l Install VMware Tools version 10 or later. For best results, ensure that all virtual
machines run the latest available version of VMware Tools. Older versions are
known to cause failures when you perform browse actions during file-level restore
or SQL restore operations.
l You can perform file-level restore across vCenters as long as the vCenters are
configured in the same NetWorker server, and the source and target virtual
machine have the same guest operating system. For example, Linux to Linux, or
Windows to Windows.
l File-level restore from a Data Domain Cloud Tier device is not supported. To
perform file-level restores of data that resides only on this device, first clone the
data to a Data Domain device, and then recover the data from the Data Domain
device.
l File-level restore does not support the following virtual disk configurations:
n LVM thin provisioning
n Unformatted disks
n FAT16 file systems
n FAT32 file systems
n Extended partitions (Types: 05h, 0Fh, 85h, C5h, D5h)

File-level restore and SQL restore limitations 169

Recover virtual machines and data

n Two or more virtual disks mapped to single partition

n Encrypted partitions
n Compressed partitions
Platform-specific limitations
Review the following limitations specific to Linux and Windows operating systems.
l You can only restore files and/or folders from a Windows backup to a Windows
machine, or from a Linux backup to a Linux machine.
l When you enable Admin Approval Mode (AAM) on the operating system for a
virtual machine (for example, by setting Registry/
FilterAdministratorToken to 1), the administrator user cannot perform a
file-level restore to the end user's profile, and an error displays indicating "Unable
to browse destination." For any user account control (UAC) interactions, the
administrator must wait for the mount operation to complete, and then access the
backup folders located at C:\Program Files (x86)\EMC\vProxy FLR
Agent\flr\mountpoints by logging into the guest virtual machine using
Windows Explorer or a command prompt.
l The FLR Agent installation on Linux virtual machines requires you to use the root
account. If credentials for any other user are provided for the target virtual
machine, the FLR Agent installation fails, even if this user has privileges similar to
a root user. Once the FLR Agent installation is completed by a root user, you can
perform file-level restore operations as a non-root user.
l Mounting a Linux virtual machine for file-level restore requires a local Linux
account with permissions to the file system files.
l When you perform file-level restore on Ubuntu/Debian platforms, you must enable
the root account in the operating system. By default, the root account will be in
locked state.
l File-level restore is not supported on Ubuntu/Debian ext4 file systems.
l When running the NetWorker server on Windows platforms, file-level restore
session logs are not kept.
l For file-level restores on Windows 2012 R2 virtual machines, the volumes listed
under the virtual machine display as "unknown." File-restore operations are not
impacted by this issue.
l File-level restore of virtual machines with Windows dynamic disks is supported
with the following limitations:
n The restore can only be performed when recovering to a virtual machine
different from the original. Also, this virtual machine cannot be a clone of the
original.
n The restore can only be performed by virtual machine administrator users.
n If Windows virtual machines were created by cloning or deploying the same
template, then all of these Windows virtual machines may end up using the
same GUID on their dynamic volumes.
l File-level restore of Windows 8, Windows Server 2012 and Windows Server 2016
virtual machines is not supported on the following file systems:
n Deduplicated NTFS
n Resilient File System (ReFS)
n EFI bootloader

170 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Restore operations and performance limitations

Review the following limitations related to file-level restore operations and
performance considerations.
l When a file-level restore or SQL restore operation is in progress on a virtual
machine, no other backup or recovery operation can be performed on this virtual
machine. Wait until the file-level restore session completes before starting any
other operation on the virtual machine.
l When the backup chain for an SQL instance restore contains 30 or more
transaction log backups, a message indicating the required permissions to
complete this action does not display in the Dell EMC Data Protection Restore
Client. Check the flr-server log for an error message similar to the following
to determine what additional privileges are required:
ERROR c.e.f.u.ProcessRestores - Failed restore attempt:
Recover request failed: Permission denied, user does not
have 'Create Application Settings' or 'Configure NetWorker'
privilege to create this resource - NSR recover.
l SQL instance restore fails in the Dell EMC Data Protection Restore Client when
the backup chain contains more than 75 transaction log backups. In such
scenarios, ensure that you perform a SQL database restore for each database in
the SQL instance one at a time.
l When you switch between different Data Domain devices for backup and clone
operations, the SQL transaction log backup does not get promoted to FULL on the
primary backup device. As a result, the transaction log backup fails with the error
Previous backup path must be specified for Transaction Log
backup. Note that this issue does not occur when the same Data Domain device
is used for the backup and clone.
If relabelling of the primary device has occurred, or you added a new Data Domain
device, unselect the Tlog backup option for the Backup Action, and then run the
SQL application-consistent workflow. After the FULL backup and clone
completion, re-select the Tlog backup option for the Backup Action and run the
SQL application-consistent workflow again. Subsequent transaction log backups
and clones will complete successfully.
l For file-level restore of high-density file systems (more than few hundred files/
folders), it is recommended to use either the NetWorker Management Web UI or
the Dell EMC Data Protection Restore Client (User or Admin mode, as
applicable) instead of the Recovery wizard in the NMC NetWorker
Administration window.
l A restore of individual SQL Server databases or instances in the Dell EMC Data
Protection Restore Client will overwrite the existing database, even if your
NetWorker version provides an option where you can unselect Overwrite the
existing DB.
l A SQL database restore to alternate is only supported for restoring from a lower
SQL version to a higher SQL version.
l The Dell EMC Data Protection Restore Client incorrectly allows you to select a
VMware Backup appliance as a destination client for file-level restore.
l After migrating from the VMware Backup appliance to the vProxy appliance, the
Dell EMC Data Protection Restore Client may continue to display VMware
Backup appliance backups along with the new vProxy backups for virtual
machines. Note, however, that you will only be able to perform file-level restore
from the new vProxy backups.
l After migrating from the VMware Backup appliance to the vProxy appliance, new
vProxy backups of virtual machines that were previously backed up with the

File-level restore and SQL restore limitations 171

Recover virtual machines and data

VMware Backup appliance will not be visible in the Dell EMC Data Protection
Restore Client in Admin mode. You must log in using User mode to view and
recover from these backups.
l You cannot use clone volumes for file-level restore when the primary backup
volume is unmounted or unavailable. The restore will fail looking for backup
volumes. If this occurs, dynamic staging allows you to use the secondary copy by
staging the requested virtual machine backups from the clone to an available
backup volume and then recovering the virtual machine.
l Browsing a large number of files at once may cause Internet Explorer to become
slow or unresponsive. The Chrome and Mozilla browsers issue a warning when
encountering a difficulty handling many files, but Internet Explorer does not.
l In a large environment where many virtual machines appear in the Dell EMC Data
Protection Restore Client, the navigation buttons (Back, Next, Finish) may
appear very small, requiring you to zoom in to see the options. It is recommended
that you use the latest versions of the Chrome or Firefox browsers to avoid the
issue.
l File-level restore supports direct restore from a cloned backup only if the clone
copy is on a Data Domain device.
l File-level restore does not restore or browse symbolic links.
l When you create partitions, fill the lower ordered indices first. For example, you
cannot create a single partition and place it in the partition index 2, 3, or 4. You
must place the single partition in partition index 1.

Using the Dell EMC Data Protection Restore Client for file-level restore and
SQL restore
The Dell EMC Data Protection Restore Client, which you access through a web
browser, allows you to select specific virtual machine backups as file systems, and
then browse the file system to locate the directories and files you want to restore. The
browser also allows you to restore individual SQL databases and instances.
The login page of the Dell EMC Data Protection Restore Client features two tabs—
an FLR tab for virtual machine file and folder restore, and an App tab for SQL
database and instance restore.
Additionally, the Dell EMC Data Protection Restore Client operates in one of two
user modes:
l User—For file-level restore, a user account that can restore folders or files to the
original virtual machine, as described in the section Restoring specific folders or
files to the original virtual machine (User mode).
For SQL restore, a user account that can restore individual SQL databases and
instances to the original machine from the virtual machine you are logged into.
This user can be an Authentication Service user, as described in the section
Restore of SQL Server application-consistent backups.
l Admin—For file-level restore, a NetWorker administrator account or
Authentication Service user that can restore folders or files from a different virtual
machine to any available destination client, as described in the section Restoring
specific folders or files from a different virtual machine (Admin mode).
For SQL restore, a NetWorker administrator account or Authentication Service
user that can restore individual SQL databases and instances to the original
machine from any virtual machine you have access to that contains an SQL Server
application-consistent backup, or restore to a different virtual machine, as
described in the section Restore of SQL Server application-consistent backups.

172 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Note

When a file-level restore operation is in progress on a virtual machine, no other backup

or recovery operation can be performed on this virtual machine. Wait until the file-
level restore session completes before starting any other operation on the virtual
machine.

Restoring specific folders or files to the original virtual machine in User mode
To restore specific folders and files to the original virtual machine on Windows and
Linux virtual machines, select the User tab in the Dell EMC Data Protection Restore
Client login page. In this mode, you connect to the Dell EMC Data Protection
Restore Client from a virtual machine that has been backed up by the vProxy
Appliance.
Before you begin
For the Data Domain resource, ensure that you provide the management credentials
and, if required, enter the export path appropriately. The section Entering
management credentials for the Data Domain resource (instant recovery and User
mode file-level restore only)provides detailed steps.
Additionally, you must create a user in the NetWorker Authentication Service by using
the NetWorker Management Console (NMC), as described in the section Create a
user in the NetWorker authentication service (User mode file-level restore only).
Procedure
1. Open a browser from the virtual machine that the restored files will be
recovered to, and enter a URL that points to the NetWorker server host and
indicates file-level restore. For example:

https://NetWorker server:9090/flr

Note

For User recoveries, you must connect to the NetWorker server from a web
browser on the virtual machine that will receive file-level restore data.

The Dell EMC Data Protection Restore Client login window appears.
2. Select the User tab and the FLR tab, and then log in to the Dell EMC Data
Protection Restore Client with the user credentials of the virtual machine to
which you are logged in. This user account should also belong to the NetWorker
user group "VMware FLR Users" in order to be authorized to perform file-level
restore. The section NetWorker privileges required by File-level restore users
provides more information.
When you log in, the Select Backups page displays with a list of backups for
the local virtual machine.
3. On the Select Backups page, use the drop-down list to view the available
backups. You can set the backup filter to view backups on a specific day or
within a specific date range. Highlight a backup and double-click or drag and
drop to move the backup to the Selected Items pane. Click Next.

Using the Dell EMC Data Protection Restore Client for file-level restore and SQL restore 173
Recover virtual machines and data

Figure 60 Select backups to restore from

Note

When you click Next, if a folder hierarchy does not appear, the Dell EMC Data
Protection Restore Client may not support the file system in use on the virtual
machine. The section File-level restore limitations provides more information.

4. On the Restore Options page, navigate to the file system drive where you want
to restore the items and select an existing folder, or specify a new folder name
in the restore destination, and then click Next.
Figure 61 Select restore location

Note

Additionally, you can select the Overwrite existing files and folders option if
you want to replace the existing files with the recovered files.

5. On the Select items to restore page, browse and select the files and folders
available for recovery. Note that you can sort items by Name, File size, or Date,

174 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

and you can also search for a specific file or folder name. To mark an item for
recovery, double-click the item, or drag and drop the item into the Selected
Items pane.
Figure 62 Select items to restore

6. When finished selecting items, click Finish.

7. Click Yes when you are prompted to continue the restore.
8. To enable the polling feature so that you can monitor the status of the restore,
click the hourglass icon located in the upper right-hand corner of the window
and set to ON. By default, the polling feature is set to OFF due to the memory
consumption that occurs when the server is queried every few seconds for the
restore status.
9. Once the polling feature is enabled, you can monitor the status of the restore by

clicking the icon located in the upper right-hand corner of the window.

When you click the icon, the Restore Detail pane slides into view on the
right side of the window, displaying the ongoing restore operations. Clicking the
entry displays the progress of the restore and a recovery logs download option.

Using the Dell EMC Data Protection Restore Client for file-level restore and SQL restore 175
Recover virtual machines and data

Figure 63 Restore Monitoring

Restoring specific folders or files from different virtual machines in Admin mode
To restore specific folders or files from a different virtual machine, select the Admin
tab in the Dell EMC Data Protection Restore Client login page. Once connected, you
can browse, select, and restore files and folders from any virtual machine that you
backed up with the vProxy Appliance. You can then restore items to the virtual
machine on which you are currently logged in, or to any available destination virtual
machine.
Procedure
1. Open a browser and specify a URL that points to the NetWorker server and
indicates FLR, as in the following example:
https://NetWorker server:9090/flr
The Dell EMC Data Protection Restore Client login window appears.
2. Click the Admin tab and the FLR tab, and then log in to the Dell EMC Data
Protection Restore Client with the NetWorker Authentication Service User
credentials.

Note

When using Admin mode, ensure that the user you specify for the NetWorker
server login has the correct privileges to use this option.

When you log in, the Select Backups page appears with a list of all the virtual
machines that were backed up by using the vProxy Appliance. The available
backups appear under each virtual machine, as shown in the following.

176 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 64 Select the backup(s) to restore from

Note

After migrating from the VMware Backup appliance to the vProxy appliance,
new vProxy backups of virtual machines that were previously backed up with
the VMware Backup appliance will not be visible in the Dell EMC Data
Protection Restore Client in Admin mode. You must log in using User mode to
view and recover these backups.

3. On the Select Backups page, use the arrows to the right of the entry to view
the available backups. You can set the backup filter to view backups on a
specific day or within a specific date range. Highlight a backup and double-click
or drag and drop to move the backup to the Selected Items pane. Click Next.
4. On the Restore Options page, select a destination virtual machine.
A login dialog box similar to the following figure appears for the restore
destination.

Using the Dell EMC Data Protection Restore Client for file-level restore and SQL restore 177
Recover virtual machines and data

Figure 65 Select restore location

5. Log in to the destination virtual machine to initiate the mounting of the backup.
6. After you successfully log in, select the restore location. If desired, specify a
new folder name in this location. Click Next.

Note

Additionally, you can select the Overwrite existing files and folders option if
you want to replace the existing files with the recovered files.

7. On the Select items to restore page, browse and select the files and folders
available for recovery. Note that you can sort items by Name, File size, or Date,
and you can also search for a specific file or folder name. To mark an item for
recovery, double-click the item, or drag and drop the item into the Selected
Items pane.

178 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 66 Select items to restore

Within this window, you can also discover and select the total number of items
available for recovery by scrolling to the far right of the directory structure and
right-clicking the icon located on the vertical scroll bar, as shown in the
following figure.
Figure 67 Total items available for recovery

8. When finished selecting items, click Finish.

9. Click Yes when you are prompted to continue with the restore.
10. To enable the polling feature so that you can monitor the status of the restore,
click the hourglass icon located in the upper right-hand corner of the window
and set to ON. By default, the polling feature is set to OFF due to the memory
consumption that occurs when the server is queried every few seconds for the
restore status.
11. Once the polling feature is enabled, you can monitor the status of the restore by

clicking the icon located in the upper right-hand corner of the window.

When you click the icon, the Restore Detail pane slides into view on the
right side of the window, displaying the ongoing restore operations. Clicking the
entry displays the progress of the restore and a recovery logs download option.

Using the Dell EMC Data Protection Restore Client for file-level restore and SQL restore 179
Recover virtual machines and data

Figure 68 Restore Monitoring

Restoring SQL Server application-consistent backups (Windows platforms only)

NetWorker 18.1 allows you to restore an individual SQL database or an entire SQL
instance for a virtual machine that was backed up as part of a SQL Server application-
consistent protection policy. You can perform this restore to a running virtual
machine, providing you with operational recovery of SQL databases and disaster
recovery of SQL instances. Additionally, alternate restore allows you to restore to a
database copy. Once you restore SQL database FULL backups, you can also apply
SQL database transaction log backups to those databases. The individual database or
instance restore target location can be the original location, or a new location on
either the original virtual machine or a different virtual machine, with the ability to
select the SQL instance where the database will be restored, the option to change the
database name, and the option to select specific folder locations for file and log
placement. Note that the ability to select a different virtual machine is only possible
for individual SQL database restore. When performing SQL instance restore, you are
restricted to selecting the original virtual machine and original instance.
SQL restore functionality is provided in the Dell EMC Data Protection Restore Client
by using the App mode button on the login page. In App restore mode, the display of
virtual machines and their primary backups is limited to virtual machines that have
application consistent backups. Once a primary backup is selected, an additional index
is loaded that allows you to browse and select the SQL instances, databases, and the
database backup versions.
The Backup Versions pane displays the database backup versions on the original
virtual machine, with a cumulative history of FULL and transaction log backups for
that database for one cycle of the backup policy. The Backup Versions pane
refreshes with each full backup, and each subsequent transaction log backup adds the
transaction log backup versions. The cumulative backup history allows you to select a
database and associated backup regardless of the primary backup that is selected.
When you select a SQL instance or SQL database to restore and do not select a
specific backup version, the most recent backup version of the selected primary
backup will be restored automatically.
The Dell EMC Data Protection Restore Client requires the virtual machine
administrative credentials during mounting of the primary FULL backup on the original
virtual machine. During the mount, NetWorker also installs or upgrades the FLR Agent
and Microsoft VM App Agent, if required, on the selected virtual machine
The Dell EMC Data Protection Restore Client will discover and display the SQL
instance on the target virtual machine once the mount completes. If the target virtual

180 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

machine does not have any running SQL Instances, an error will be displayed. You may
select the SQL instance from this where you want to restore the database. The ability
to select a different SQL Instance is only possible for individual database restore, and
when performing SQL Instance restore you are restricted to selecting the original SQL
Instance.
NetWorker automates the complete restore of SQL databases, restoring the database
FULL and any transaction log backups as a single operation according to the following
sequence:
l The primary FULL database backup is identified, mounted on the original virtual
machine, and the SQL database files from the FULL backup are restored to the
original database.
l If a transaction log backup was selected, the series of transaction logs that
occurred after the FULL backup to the selected transaction log are restored in
sequence.
NetWorker automates the complete restore of SQL instances according to the
following sequence:
l The master database is restored first, then msdn, then model. During this
restore, the SQL instance restarts in single-user mode as required by the
Microsoft SQL Server to restore the master database. When the restore
completes, the SQL services restart in multi-user mode.
l Each remaining database is restored individually, and includes the backup versions
present in the currently selected backup.
The Dell EMC Data Protection Restore Client provides the ability to monitor the
restore operations while in progress by enabling the Polling feature, which is disabled

by default. Once enabled, when you click the icon, the Restore Detail pane slides
into view on the right side of the window, displaying the ongoing restore operations.
Clicking the entry displays the progress of the restore and a recovery logs download
option.

Restore specific SQL databases and instances to a running virtual

machine (Windows platforms only)
To restore specific SQL instances and databases to a running virtual machine in the
Dell EMC Data Protection Restore Client, select the App button, and then select
User or Admin. In User mode, you can log in and connect to the virtual machine that
was backed up as part of a SQL Server application-consistent protection policy to
restore to the original virtual machine. In Admin mode, you can browse, select, and
restore from any virtual machine that you backed up as part of a SQL Server
application-consistent protection policy. In both modes, you can restore the virtual
machine's SQL instance(s) to the original SQL instance, or an alternate SQL instance.
Before you begin
When planning to restore to an alternate instance between virtual machines in
different domains, ensure that DNS is resolved.
For the Data Domain resource, ensure that you provide the management credentials
and, if required, enter the export path appropriately. The section Entering
management credentials for the Data Domain resource (instant recovery and User
mode file-level restore only)provides detailed steps.
Additionally, if not using the NMC Administrator account to log in, you must create a
user in the NetWorker Authentication Service by using the NetWorker Management
Console (NMC), as described in the section Create a user in the NetWorker
authentication service (User mode file-level restore only), and you must configure

Using the Dell EMC Data Protection Restore Client for file-level restore and SQL restore 181
Recover virtual machines and data

Microsoft SQL Server instances in the original virtual machine to allow SYSTEM
account login and membership in the SQL sysadmin role.
Procedure
1. Open a browser from the virtual machine that the SQL databases or instances
will be recovered to, and enter a URL that points to the NetWorker server host
and indicates file-level restore. For example:

https://NetWorker server IP:9090/flr

The Dell EMC Data Protection Restore Client login window appears.

2. Select the User or Admin tab, and then select the App tab.

Note

For User mode recoveries, you must connect to the NetWorker server from a
web browser on the virtual machine that the SQL database or instance will be
restored to.

3. Type the user credentials, and then click Login.

l For User mode, type the NetWorker credentials. These can be your NMC
credentials, or the user account credentials specified for the NetWorker user
group VMware FLR Users. This user must belong to the VMware FLR
Users group in order to be authorized to perform SQL database or instance
restore. The section NetWorker privileges required by File-level restore
users provides more information.
l For Admin mode, type the NetWorker credentials. When using this mode,
ensure that the user you specify for the NetWorker server login has the
correct privileges to use this option.
When you log in, the Select App Backups page displays with a list of virtual
machines that were backed up by the SQL Server application-consistent
protection policy. The available backups (primary backups) appear under each
virtual machine, and include the virtual machine FULL and transaction log
backups, depending on the application-consistent policy settings. For User
mode, this will be limited to a list of backups for the local virtual machine.

Note

The polling feature, which enables monitoring of in-progress restore operations,

is turned off by default. To turn on the polling feature, click the hourglass icon
located in the upper right-hand corner of the window and set to ON.

4. On the Select App Backups page, use the arrows to the right of the entry to
browse and select from the available SQL Server application-consistent
backups, including all SQL instances, databases, and backup versions.
To select a backup version, expand the SQL instance and database to display
the backup versions pane, and then click the backup version item once or drag
and drop the item to move the backup to the Selected Items pane. You may be
required to scroll right to view the backup versions.

To select a SQL database or instance, drag and drop the entry to move the item
to the Selected Items pane. Note that you cannot drag and drop the SQL
database or instance when the entry has been expanded to view its children. If

182 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

you expanded the entry, reselect the virtual machine, and then select the SQL
database or instance to enable drag-and-drop.

Note

The backup filter is set to the last seven days by default. You can expand the
date range further back if desired.

Figure 69 Select App Backups page

When finished, click Next. The Restore Target page displays.

5. On the Restore Target page, select the running virtual machine to which you
want to restore the items. For an individual SQL database restore in User mode,
you can only select the original virtual machine as the restore target. For an
individual SQL database restore in Admin mode, you can select the original
virtual machine or a different virtual machine as the restore target. For SQL
instance restore, you must select the original virtual machine as the restore
target.
The Dell EMC Data Protection Restore Client prompts you to provide the
system administrative credentials of the target virtual machine to initiate the
mount of the backup and to verify that the vProxy FLR Agent and Microsoft VM
App Agent are installed on this virtual machine.
Figure 70 Restore Target page

Using the Dell EMC Data Protection Restore Client for file-level restore and SQL restore 183
Recover virtual machines and data

When the mount completes, all SQL instances running on the selected virtual
machine display in this window.

Note

If the SQL Server is not installed, or there are no SQL instances running, an
error displays. If this occurs, log out of the Dell EMC Data Protection Restore
Client to cancel the mount.

6. Select the SQL instance where you want to restore the database, and then click
Next.
The Restore Options page displays.
7. On the Restore Options page, set the Diagnostic logging level, if required.
The default level is 0.
8. Select Leave the DB in recovery state if you want to activate the SQL Server
NORECOVERY database restore option, which places the database in a
recovering state upon completion of the restore and is useful for special
situations such as restoring transaction log backups taken by third-party
applications. Note that this option is not available for SQL instance restore. This
option also overwrites the database and then leaves the database in restoring
state.
9. In the Target Database Name field, you can type a new name if you want to
change the name of the database, or leave the current name. By default, this
field displays the name of the database at the time of backup.

Note

If you change the database name, the new name must comply with the
Microsoft SQL Server rules for database naming. Also, if you change the name
and another database with the same name already exists on the target virtual
machine and SQL instance, a warning displays that this database will be
overwritten if you proceed.

10. For the restore location, select from one of the following options under Restore
files to:
l Original Location—Select this option to restore the database files to the
original, or current, location. This option is only available if the original virtual
machine and SQL instance were selected as the restore target. By default,
the files are restored to the database location as it was at the time of
backup. Note, however, that if the database file locations were changed
after the backup, the files will be restored to the changed location.
l Default data path—Select this option to restore the database files to the
default data path for the target SQL Server instance. Each SQL Server
instance has a configuration variable for the default database data path and
log file path. When you select this option, all SQL data files will be restored
to the default data path, and all log files will be restored to the default log
path.
l Folder —Allows you to specify the folders where you want to restore the
database and log files. With this option, you can specify two folder locations
on the target virtual machine; one folder to store all the data files for the
database, and another folder to store all the log files for the database. Click
Browse to navigate the file system on the target virtual machine and select
the desired folders. By default, both folder locations are populated with the

184 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

SQL default data paths for the target SQL Server instance. Note that you
can only select an existing folder and cannot create a new folder using the
Dell EMC Data Protection Restore Client.
Figure 71 Restore Options page

11. Select Restore Stop At Time if you want to restore transaction logs from the
backup version that occurred before the specified restore date and time. This
option is only available when you select a specific transaction log backup.
12. Click Restore.

Note

A restore of individual SQL Server databases or instances in the Dell EMC Data
Protection Restore Client will overwrite the existing database.

13. In the Restore Confirmation dialog, click Yes to continue the restore and
overwrite the existing database, or No to exit the restore.
If you changed the name of the database and another database with the same
name already exists on the target virtual machine and SQL instance, an
additional warning displays that this database will be overwritten if you proceed.
If you changed the name of the database and the name does not match any
available databases on the target virtual machine and SQL instance, an
additional warning displays indicating that a new database will be created.
14. To enable the polling feature so that you can monitor the status of the restore,
click the hourglass icon located in the upper right-hand corner of the window
and set to ON. By default, the polling feature is set to OFF due to the memory
consumption that occurs when the server is queried every few seconds for the
restore status.
15. Once the polling feature is enabled, you can monitor the status of the restore by

clicking the icon located in the upper right-hand corner of the window.

When you click the icon, the Restore Detail pane slides into view on the
right side of the window, displaying the ongoing restore operations. Clicking the
entry displays the progress of the restore and a recovery logs download option.
For SQL database restore, a single line displays. For SQL instance restore, one
line per database displays. In both cases, the Target field indicates the database
associated with the progress line.

Using the Dell EMC Data Protection Restore Client for file-level restore and SQL restore 185
Recover virtual machines and data

Figure 72 Restore Monitoring

vProxy recovery in the vSphere Client's Dell EMC

NetWorker interface
You can also perform virtual machine image-level recoveries of vProxy backups by
using the vSphere Client HTML-5 based Dell EMC NetWorker interface. Recoveries
can be performed to the original virtual machine or to a new virtual machine.
Dell EMC NetWorker appears in the left navigation pane of the vSphere Client after
you install the vCenter plug-in. The section Installing the vCenter plug-in provides
instructions.

Note

Backup and recovery operations in the vSphere Client Dell EMC NetWorker
interface are not supported for SQL Server advanced application-consistent
protection policies. Perform these operations from the NMC NetWorker
Administration window or the Dell EMC Data Protection Restore Client.

Connect to the NetWorker server in the vSphere Client

You must establish a connection to the NetWorker server before performing any
vProxy backup and recovery operations in the vSphere Client.
Before you begin
Dell EMC NetWorker only appears in the vSphere Client after you install the vCenter
plug-in. The section Installing the vCenter plug-in provides instructions.
Procedure
1. Login to the vSphere Client as an administrator, or as a non-administrator
Active Directory user that you created using the steps in the section Using the
vCenter plug-in as a non-administrator Active Directory user.
2. In the vSphere Client, select Menu > Dell EMC NetWorker, or select Dell
EMC NetWorker in the left pane.

186 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 73 Accessing Dell EMC NetWorker in the vSphere Client

A prompt displays in the right pane with fields required to connect to the
NetWorker server.
3. For the NetWorker server, type the following information:
a. In the Username field, type the NetWorker administrator username.
b. In the Password field, type the NetWorker administrator password.
c. In the NetWorker Server field, type the IP address of the NetWorker
server.
d. In the Port field, type 9090.
Figure 74 NetWorker connection information in the vSphere Client

4. Click Log in.

Results
When a connection to the NetWorker server is established, the Basic Tasks pane
appears, as shown in the following.

Connect to the NetWorker server in the vSphere Client 187

Recover virtual machines and data

Figure 75 Dell EMC NetWorker Basic Tasks pane

Accessing the vCenter plug-in as a non-administrator Active Directory user

You can only access the vCenter plug-in (the Dell EMC NetWorker interface) in the
vSphere Client if you are an NetWorker administrator or a non-administrator Active
Directory user associated with appropriate privileges in NetWorker. The following
procedure describes how to access the plug-in as a non-administrator Active Directory
user.
Before you begin
Install the vCenter plug-in. The section Installing the vCenter plug-in provides
instructions.
Procedure
1. Create a vmwareAdmin group in NetWorker that contains the following
privileges at a minimum:
l View Security Settings
l View Application Settings
l Remote Access All Clients
l Operate NetWorker
l Monitor NetWorker
l Operate Devices and Jukeboxes
l Recover Local Data
l Recover Remote Data
l Backup Local Data

2. Create an Active Directory user within your desired security group.

3. Add the user and group to the NetWorker Management Console's External
Roles attribute. For example:
CN=VMwareTeam,CN=Users,DC=vproxy,DC=com

188 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

cn=VMwareUser,cn=Users,dc=vproxy,dc=com
where VMwareTeam is the security group name, and VMwareUser is the Active
Directory user name.
4. Log in to the vSphere Web Client as the Active Directory user, in the format
<tenant>\<domain>\<userid>. For example:

default\vproxy\VMwareUser

Results
The Active Directory user that you create using these steps will only have access to
the vSphere Client Dell EMC NetWorker interface, and cannot be used to log in to
NetWorker Management Console. If you also need to provide access to NMC, then
add those required privileges accordingly.

Recovery to the original virtual machine

To start a vProxy image-level recovery to the original virtual machine by using the Dell
EMC NetWorker interface in the vSphere Client, perform the following steps.
Before you begin
Ensure that the virtual machine you want to restore to is in powered OFF state.
Procedure
1. In the vSphere Client, if not already selected, click Dell EMC NetWorker in the
left pane.
When a connection to the NetWorker server is established, links to Basic Tasks
appear in the right pane.
2. From the Basic Tasks pane, click Restore Backup, or click the Restore icon

in the vertical navigation bar.

A list of existing virtual machine client backups for the selected vCenter server
host displays in the Client pane.
Figure 76 Restore pane with available virtual machine backups

Note

If this list does not contain a virtual machine that was recently backed up,
refresh the window.

Recovery to the original virtual machine 189

Recover virtual machines and data

3. From the Client pane, click the radio button next to the virtual machine that
you want to recover.
A list of available restore points for that virtual machine displays in the right
pane. You can also specify a date range to view only the virtual machine
backups that were performed within that range.
4. Within the Restore pane, click the radio button next to the desired restore
point.
5. In the top-right of the Restore pane, click the Action icon and select Restore
from the drop-down.
Figure 77 Select Restore from the Action drop-down

The Restore wizard opens on the Basic Config page.

6. From the Destination drop-down, leave the default Restore to original
location selected.
Figure 78 Restore to original location

7. (Optional) Select from the following options:

a. Power on vm—Select this checkbox to automatically power on the virtual
machine after the restore completes.
b. Reconnect nic—Select this checkbox to automatically reconnect the
network interface card after the restore completes.
8. Click Next.
9. In the Summary page, review the information and then click Finish to start the
recovery.

190 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Results
You can monitor the progress of the recovery in the Recent Tasks pane. Once the
recovery completes successfully, power ON the virtual machine to validate the
recovery.

Recovery to a new virtual machine

To start a vProxy image-level recovery to a new virtual machine by using the Dell
EMC NetWorker interface in the vSphere Client, perform the following steps.
Procedure
1. In the vSphere Client, if not already selected, click Dell EMC NetWorker in the
left pane.
When a connection to the NetWorker server is established, links to Basic Tasks
appear in the right pane.
2. From the Basic Tasks pane, click Restore Backup, or click the Restore icon

in the vertical navigation bar.

A list of existing virtual machine client backups for the selected vCenter server
host displays in the Client pane.
Figure 79 Restore pane with available virtual machine backups

Note

If this list does not contain a virtual machine that was recently backed up,
refresh the window.

3. From the Client pane, click the radio button next to the virtual machine that
you want to recover.
A list of available restore points for that virtual machine display in the right
pane. You can also specify a date range to view only the virtual machine
backups that were performed within that range.
4. Within the Restore pane, click the radio button next to the desired restore
point.
5. In the top-right of the Restore pane, click the Action icon and select Restore
from the drop-down.

Recovery to a new virtual machine 191

Recover virtual machines and data

Figure 80 Select Restore from the Action drop-down

The Restore wizard opens on the Basic Config page.

6. From the Destination drop-down, select Restore to new Virtual Machine.
Figure 81 Restore to new virtual machine

7. (Optional) Select from the following options:

a. Restore Virtual Machine Configuration—Select this checkbox to restore
this virtual machine with the existing configuration settings.
b. Power on vm—Select this checkbox to automatically power on the virtual
machine after the restore completes.
c. Reconnect nic—Select this checkbox to automatically reconnect the
network interface card after the restore completes.
8. Click Next.
The Advanced Config page displays.
9. From the vCenter drop-down, select the destination vCenter server, and then
specify a name for the new virtual machine. Click Next.
The Location page displays.
10. Expand the vCenter server tree and select a destination for recovery within the
vCenter server, and then click Next.
The Host/Cluster page displays.
11. Select a host within the destination datacenter, and then click Next.
The Resource Pool page displays.
12. Select a resource pool, and then click Next.
The Datastore page displays.

192 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

13. From the Destination Datastore drop-down, select a datastore that is

compatible with the virtual machine, and then click Next.
14. In the Summary page, review the information and then click Finish to start the
recovery.
Results
You can monitor the progress of the recovery in the Recent Tasks pane. Once the
recovery completes successfully, power ON the virtual machine to validate the
recovery.

Virtual disk recovery (restore to an existing virtual machine)

To start a VMDK recovery to an existing virtual machine by using the Dell EMC
NetWorker interface in the vSphere Client, perform the following steps.
Procedure
1. In the vSphere Client, if not already selected, click Dell EMC NetWorker in the
left pane.
When a connection to the NetWorker server is established, links to Basic Tasks
appear in the right pane.
2. From the Basic Tasks pane, click Restore Backup, or click the Restore icon

in the vertical navigation bar.

A list of existing virtual machine client backups for the selected vCenter server
host displays in the Client pane.
Figure 82 Restore pane with available virtual machine backups

Note

If this list does not contain a virtual machine that was recently backed up,
refresh the window.
3. From the Client pane, click the radio button next to the virtual machine that
you want to recover.
A list of available restore points for that virtual machine displays in the right
pane. You can also specify a date range to view only the virtual machine
backups that were performed within that range.
4. Within the Restore pane, click the radio button next to the desired restore
point.

Virtual disk recovery (restore to an existing virtual machine) 193

Recover virtual machines and data

The Content pane displays the virtual disks available for recovery.
5. Select the checkbox next to the disk(s) in the Content pane that you want to
recover. When selected, the disk will appear in the Restore Selection pane.
6. Click the Action icon and select Restore from the drop-down.
Figure 83 Select Restore from the Action drop-down

The Restore wizard opens on the Basic Config page.

7. From the Destination drop-down, select Restore to different (existing)
virtual machine.
Figure 84 Restore virtual disks to existing virtual machine

8. (Optional) Select from the following options:

a. Reconnect nic—Select this checkbox to automatically reconnect the
network interface card after the restore completes.
b. Power on vm—Select this checkbox to automatically power on the virtual
machine after the restore completes.
9. Click Next.
The Advanced Config page displays.
10. In the Host/Cluster pane, select the location in the datacenter of the existing
virtual machine(s). A list of virtual machines for this location displays in the
Virtual Machines pane. You can click the + icon next to a virtual machine to
view more details.
11. Click Next.
The Datastore page displays.
12. For each virtual disk listed in the Datastore pane, select a Destination
Datastore from the drop-down, and then click Next.

194 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

13. In the Summary page, review the information and then click Finish to start the
recovery.

WARNING

When you start a VMDK recovery, the virtual machine will be powered off
automatically without issuing a warning message.

Results
You can monitor the progress of the recovery in the Recent Tasks pane. Once the
recovery completes successfully, power ON the virtual machine to validate the
recovery.

Instant recovery of a virtual machine

To start an instant recovery to a new virtual machine by using the Dell EMC
NetWorker interface in the vSphere Client, perform the following steps.
Before you begin
Note the following before performing an instant recovery in the Dell EMC NetWorker
interface:
l Ensure that you provide the management credentials for the Data Domain
resource before you initiate the recovery. If you do not configure the management
credentials in NMC prior to the recovery, the recovery will fail silent without an
error message. The section Entering management credentials for the Data Domain
resource (instant recovery and User mode file-level restore only) provides
instructions.
l Ensure that you do not perform an instant recovery of virtual machines in resource
pools and other similar containers that are part of a currently running protection
group.
l Ensure that the free space on the Data Domain system is equal to or greater than
the total disk size of the virtual machine being restored, as the restore does not
take into account the actual space required after deduplication occurs. If there is
insufficient disk space, an error appears indicating "Insufficient disk space on
datastore," and creation of the target virtual machine fails.
Procedure
1. In the vSphere Client, if not already selected, click Dell EMC NetWorker in the
left pane.
When a connection to the NetWorker server is established, links to Basic Tasks
appear in the right pane.
2. From the Basic Tasks pane, click Restore Backup, or click the Restore icon

in the vertical navigation bar.

A list of existing virtual machine client backups for the selected vCenter server
host displays in the Client pane.

Instant recovery of a virtual machine 195

Recover virtual machines and data

Figure 85 Restore pane with available virtual machine backups

Note

If this list does not contain a virtual machine that was recently backed up,
refresh the window.

3. From the Client pane, click the radio button next to the virtual machine that
you want to recover.
A list of available restore points for that virtual machine display in the right
pane. You can also specify a date range to view only the virtual machine
backups that were performed within that range.
4. Within the Restore pane, click the radio button next to the desired restore
point.
5. Click the Action icon and select Restore from the drop-down.
Figure 86 Select Restore from the Action drop-down

The Restore wizard opens on the Basic Config page.

6. From the Destination drop-down, select Instant Restore.

196 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 87 Instant Restore

7. Click Next.
The Advanced Config page displays.
8. Specify a name for the new virtual machine, and then click Next.
The Location page displays.
9. Expand the vCenter server tree and select a destination for recovery within the
vCenter server, and then click Next.
The Host/Cluster page displays.
10. Select a host within the destination datacenter, and then click Next.
The Resource Pool page displays.
11. Select a resource pool, and then click Next.
12. In the Summary page, review the information and then click Finish to start the
recovery.
Results
You can monitor the progress of the recovery in the Recent Tasks pane. Once the
instant restore completes, use storage vMotion to save the virtual machine, and then
cancel the vSphere NetWorker Recovery task to delete the datastore. Power ON the
virtual machine to validate the recovery.

vProxy recovery in the vSphere Web Client's VM Backup

and Recovery interface
If using a vSphere version prior to 6.5, you can still use the vSphere Web Client's
flash-based VM Backup and Recovery interface to perform image-level recoveries to
the original virtual machine or to a new virtual machine.
In the vSphere Web Client, click VM Backup and Recovery in the left navigation
pane. Once you establish a connection to the required NetWorker server, click the
Restore tab to open the Restore pane.

vProxy recovery in the vSphere Web Client's VM Backup and Recovery interface 197
Recover virtual machines and data

Connect to the NetWorker server in the vSphere Web Client

After installing the vCenter plug-in, you must establish a connection to the NetWorker
server before performing any vProxy operations in the vSphere Web Client.
Procedure
1. Log in to the vSphere Web Client as an administrator, or as a non-
administrator Active Directory user that you created using the steps in the
section Using the vCenter plug-in as a non-administrator Active Directory user.
2. In the vSphere Web Client, click VM Backup and Recovery in the left pane.
The required NetWorker connection information appears in the right pane.
Figure 88 NetWorker connection information in the vSphere Web Client

3. Enter the following information for the NetWorker server:

a. In the Host field, type the IP address of the NetWorker server.
b. In the Port field, type 9090.
c. In the User field, type the NetWorker administrator username.
d. In the Password field, type the NetWorker administrator password.
4. Click Connect.
Results
When a connection to the NetWorker server is established, the Getting Started pane
appears.

Accessing the vCenter plug-in as a non-administrator Active Directory user

You can only access the vCenter plug-in (the VM Backup and Recovery interface) in
the vSphere Web Client if you are an NetWorker administrator or a non-administrator
Active Directory user associated with appropriate privileges in NetWorker . The
following procedure describes how to access the plug-in as a non-administrator Active
Directory user.
Before you begin
Install the vCenter plug-in. The section Installing the vCenter plug-in provides
instructions.
Procedure
1. Create a vmwareAdmin group in NetWorker that contains the following
privileges at a minimum:

198 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

l View Security Settings

l View Application Settings
l Remote Access All Clients
l Operate NetWorker
l Monitor NetWorker
l Operate Devices and Jukeboxes
l Recover Local Data
l Recover Remote Data
l Backup Local Data

2. Create an Active Directory user within your desired security group.

3. Add the user and group to the NetWorker Management Console's External
Roles attribute. For example:
CN=VMwareTeam,CN=Users,DC=vproxy,DC=com
cn=VMwareUser,cn=Users,dc=vproxy,dc=com
where VMwareTeam is the security group name, and VMwareUser is the Active
Directory user name.
4. Log in to the vSphere Web Client plug-in as the Active Directory user, in the
format <tenant>\<domain>\<userid>. For example:
default\vproxy\VMwareUser

Results
The Active Directory user that you create using these steps will only have access to
the vSphere Web Client VM Backup and Recovery interface, and cannot be used to
log in to NetWorker Management Console. If you also need to provide access to NMC,
then add those required privileges accordingly.

Recovery to the original virtual machine

In the vSphere Web Client's VM Backup and Recovery interface, use the following
procedure to perform an image-level recovery to the original virtual machine.
Before you begin
Ensure that the virtual machine you want to restore to is in powered OFF state.
Procedure
1. Login to the vSphere Web Client as an administrator.
2. In the vSphere Web Client, click VM Backup and Recovery in the left pane.
When a connection to the NetWorker server is established, the Getting
Started pane appears.
3. Click Restore to open the Restore pane.
A list of virtual machines available for recovery displays.

Recovery to the original virtual machine 199

Recover virtual machines and data

Figure 89 Virtual machines for recovery in the Restore pane

If you do not see the virtual machine backup listed, refresh the window.
4. Browse the list of virtual machines and select the virtual machine backup you
want to recover. You can expand the virtual machine backup to view a list of
restore points from which to select.
Figure 90 Select a restore point

5. Select one of the restore points by clicking the checkbox next to the backup
time, and then click Restore.
The Restore Backup wizard launches.
6. In the Set Restore Options page of the Restore Backup wizard, leave the
default Restore to original location selected and click Next.
Figure 91 Restore to original location

7. In the Ready to Complete page, click Finish to start the recovery.

200 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Results
You can monitor the progress of the recovery in the Running tab of the Recent Tasks
pane. Once the recovery completes successfully, power ON the virtual machine to
validate the recovery.

Recovery to a new virtual machine

In the vSphere Web Client's VM Backup and Recovery interface, use the following
procedure to perform an image-level recovery to a new virtual machine.
Procedure
1. Login to the vSphere Web Client as an administrator.
2. In the vSphere Web Client, click VM Backup and Recovery in the left pane.
When a connection to the NetWorker server is established, the Getting
Started pane appears.
3. Click the Restore tab to open the Restore pane.
If you do not see the virtual machine backup listed, refresh the window.
4. Browse the list of virtual machines and select the virtual machine backup you
want to recover. You can expand the virtual machine backup to view a list of
restore points from which to select.
5. Select one of the restore points by clicking the checkbox next to the backup
time, and then click Restore.
The Restore Backup wizard launches.
6. In the Set Restore Options page of the Restore Backup wizard, uncheck the
default Restore to original location.
7. Specify a name for the new virtual machine, and select a destination for
recovery in the vCenter server. You are not required to select the Choose
button and can ignore the text New or Existing.
Figure 92 Restore options for the new virtual machine recovery

8. Specify a datastore for the virtual machine, and then click Next.
9. In the Ready to Complete page, click Finish to start the recovery.

Recovery to a new virtual machine 201

Recover virtual machines and data

Results
You can monitor the progress of the recovery in the Running tab of the Recent Tasks
pane. Once the recovery completes successfully, power ON the virtual machine to
validate the recovery.

Virtual disk recovery

In the vSphere Web Client's VM Backup and Recovery interface, use the following
procedure to perform a VMDK recovery to an existing virtual machine.
Procedure
1. Log in to the vSphere Web Client as an administrator.
2. In the vSphere Web Client, click VM Backup and Recovery in the left pane.
When a connection to the NetWorker server is established, the Getting
Started pane displays.
3. Click the Restore tab to open the Restore pane.
If you do not see the virtual machine backup listed, refresh the window.
4. Browse the list of virtual machines and select the virtual machine backup that
contains the VMDK you want to recover. You can expand the virtual machine
backup to view a list of restore points from which to select.
5. Double-click one of the restore points to view the list of available VMDKs for
the virtual machine.
6. Select the VMDK you want to restore by selecting the checkbox next to the
VMDK, and then click Restore.
The Restore Backup wizard launches.
Figure 93 Select VMDK backup to restore

7. In the Select Backup page, verify that the correct VMDK is selected and click
Next.
8. In the Set Restore Options page, uncheck the default Restore to original
location and then click Next.
9. Click Choose to browse the existing virtual machine where the VMDK needs to
be restored in the vCenter.

202 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 94 Set Restore Options for VMDK recovery

10. Specify a datastore for the VMDK, and then click Next.
11. In the Ready to Complete page, click Finish to start the recovery.
Results
You can monitor the progress of the recovery in the Running tab of the Recent Tasks
pane.

Note

When you start a VMDK recovery, the virtual machine will be powered off
automatically without issuing a warning message.

Instant recovery of a virtual machine

In the vSphere Web Client's VM Backup and Recovery interface, use the following
procedure to perform an instant access recovery to a new virtual machine.
Before you begin
Note the following before performing an instant access recovery in the VM Backup
and Recovery plug-in:
l Ensure that you provide the management credentials for the Data Domain
resource before you initiate the recovery. If you do not configure the management
credentials in NMC prior to the recovery, the recovery will fail silent without an
error message. The section Entering management credentials for the Data Domain
resource (instant recovery and User mode file-level restore only) provides
instructions.
l Ensure that you do not perform an instant recovery of virtual machines in resource
pools and other similar containers that are part of a currently running protection
group.
l Ensure that the free space on the Data Domain system is equal to or greater than
the total disk size of the virtual machine being restored, as the restore does not
take into account the actual space required after deduplication occurs. If there is
insufficient disk space, an error appears indicating "Insufficient disk space on
datastore," and creation of the target virtual machine fails.
Procedure
1. Log in to the vSphere Web Client as an administrator.

Instant recovery of a virtual machine 203

Recover virtual machines and data

2. In the vSphere Web Client, click VM Backup and Recovery in the left pane.
When a connection to the NetWorker server is established, the Getting
Started pane displays.
3. Click the Restore tab to open the Restore pane.
If you do not see the virtual machine backup listed, refresh the window.
4. Browse the list of virtual machines and select the virtual machine backup you
want to recover. You can expand the virtual machine backup to view a list of
restore points from which to select.
5. Select one of the restore points by selecting the checkbox next to the backup
time, and then click Instant Access.
The Restore Backup wizard launches.
6. In the Set Instant Access Options page, specify a name for the new virtual
machine, and select a destination for recovery in the vCenter server, and then
click Next. You can ignore the text New or Existing.
Figure 95 Set Instant Access restore options

7. In the Ready to Complete page, click Finish to start the recovery.

204 NetWorker 18.1 VMware Integration Guide

 Recover virtual machines and data

Figure 96 Finish Instant Access recovery

Results
You can monitor the progress of the recovery in the Running tab of the Recent Tasks
pane. Once the instant access recovery completes, use storage vMotion to save the
virtual machine, and cancel the vSphere NetWorker Recovery task to delete the
datastore. Power ON the virtual machine to validate the recovery.

vProxy recovery log files

The vProxy appliance contains log files, which you can configure to display debug
information.
The following table provides information about the vProxy recovery log files and how
to enable debugging.
Table 15 Recovery log files

Log file Log location and name Logging levels

Primary For image level To modify the logging level:
recovery log recoveries, /opt/emc/
1. Edit the /usr/lib/systemd/system/
vrproxy/runtime/
vrecoverd.service file.
logs/vrecoverd/
vrecoverd- 2. Search for the for the ExecStart= string.
engine.log.
3. Edit the --program-log-level= argument with
For file-level recoveries or one of the following values:
SQL application-consistent
recoveries, /opt/emc/ l warn
vrproxy/runtime/ l info
logs/vflrd/vflrd-
l trace
engine.log.
l debug
4. Reload the unit config file into systemd:
systemctl daemon-reload

vProxy recovery log files 205

Recover virtual machines and data

Table 15 Recovery log files (continued)

Log file Log location and name Logging levels

5. Restart the recovery engine: systemctl

restart vrecoverd.service

DD Boost For image level To modify the logging level:

recovery log recoveries, /opt/emc/
1. Edit the /usr/lib/systemd/system/
vrproxy/runtime/
vrecoverd.service file.
logs/vrecoverd/
vrecoverd-boost.log. 2. Search for the for the ExecStart= string.
For file-level recoveries or 3. Edit the --boost-log-level= argument with one
SQL application-consistent of the following values:
recoveries, /opt/emc/
vrproxy/runtime/ l none
logs/vflrd/vflrd- l error
boost.log.
l warn
l info
l trace
l debug
l all
4. Reload the unit config file into systemd:
systemctl daemon-reload
5. Restart the recovery engine: systemctl
restart vrecoverd.service

VDDK /opt/emc/vrproxy/ To modify the logging level:

recovery log runtime/logs/
1. Edit the /opt/emc/vproxy/conf/
vrecoverd/
VixDiskLib.config file.
vrecoverd-vddk.log
2. Edit the vixDiskLib.transport.LogLevel = to
specify one of the following values:
l 0—No logging
l 1—Errors only
l 2—Warnings and Errors
l 3—Important information messages, errors
and warnings
l 4 —All messages, including debug
messages.
3. Restart the recovery engine: systemctl
restart vrecoverd.service

206 NetWorker 18.1 VMware Integration Guide

CHAPTER 5
NetWorker VMware Protection with the
VMware Backup Appliance (legacy)

This chapter contains the following topics:

l Introduction to NetWorker VMware Protection with the VMware Backup

appliance (legacy)............................................................................................208
l NetWorker VMware Protection tasks for the VMware Backup appliance.........208
l System requirements....................................................................................... 209
l Port requirements............................................................................................. 211
l Download and deploy the VMware Backup appliance........................................214
l Creating a dedicated vCenter user account and VM Backup and Recovery role
.........................................................................................................................230
l Restrict mapping of datastores........................................................................ 235
l EMC Backup and Recovery Configuration Utility............................................. 235
l Post-installation configuration......................................................................... 240
l Adding or swapping a NIC for VMXNET 3 on the VMware Backup appliance or
external proxy.................................................................................................. 243
l Dual NIC support..............................................................................................246
l Verify vNIC connectivity.................................................................................. 248
l Backing up the VMware environment using NMC............................................ 249
l Managing the VMware environment using the vSphere Web Client................. 260
l Restoring the VMware environment.................................................................276
l Monitoring EMC Backup and Recovery activity............................................... 289
l Shutdown and Startup Procedures.................................................................. 292
l EMC Backup and Recovery Capacity Management..........................................292
l Checkpoints and VMware Backup Appliance rollback.......................................293
l Cross Sync.......................................................................................................295
l Disaster Recovery............................................................................................ 296
l Best practices and troubleshooting..................................................................303

NetWorker VMware Protection with the VMware Backup Appliance (legacy) 207
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Introduction to NetWorker VMware Protection with the

VMware Backup appliance (legacy)
NetWorker VMware Protection with the VMware Backup appliance is a NetWorker-
integrated VMware backup, monitoring and recovery solution introduced in NetWorker
8.x. This solution allows you to assign backup and cloning policies for a VMware
Backup appliance to Datacenters, Clusters, virtual machines and VMDKs within NMC's
NetWorker Administration window. You can also perform image-level, VMDK, or file-
level recoveries of those backups.
This solution becomes available when you deploy the VMware Backup appliance in the
vSphere server and register the appliance with NetWorker and vCenter. After running
policy workflows, you can then perform full recoveries or VMDK-level recoveries of
these backups from the vSphere Web Client EMC Backup and Recovery plug-in, or
file-level recoveries from the Dell EMC Data Protection Restore Client user
interface.

Note

NetWorker 18.1 does not support the creation of new VMware Backup appliance
policies. After upgrading to NetWorker 18.1, you can only schedule a backup of
existing VMware Backup appliance policies created in NetWorker 9.0.x releases, or
modify what contents are included in the existing policies. For the creation of new
policies, use the vProxy appliance.

It is strongly recommended to upgrade both the NetWorker server and storage node
to the latest NetWorker release, and use the latest available VMware Backup
appliance. NetWorker 18.1 does not feature a new version of the VMware Backup
appliance, but supports the OVA and proxy version compatible with Networker 9.0 and
9.0.1 for running existing VMware Backup appliance policies.

NetWorker VMware Protection tasks for the VMware

Backup appliance
The following table compares tasks in NMC's NetWorker Administration window
with tasks in the vSphere Web Client and the Dell EMC Data Protection Restore
client for NetWorker VMware Protection with the VMware Backup appliance.

Table 16 NetWorker VMware Data Protection tasks

Program/Role Task
NMC NetWorker Administration window l Modify Data Protection policies to
perform actions such as backup, clone,
and checkpoint backup for disaster
recovery.
l Assign a checkpoint discover policy to the
VMware Backup appliance.
l Assign virtual machines/VMDKs to the
policy.

208 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 16 NetWorker VMware Data Protection tasks (continued)

Program/Role Task

l Start or schedule a group/policy to run

any backup and clone actions associated
with the group/policy.
When you start a policy from the
NetWorker Administration window,
you can perform both backups and
clones, based on the actions defined in
the policy.

EMC Backup and Recovery user interface in l Assign VMs/VMDKs to a VMware Backup
the VMware vSphere Web Client appliance policy workflow.
l Start an on-demand (ad-hoc) backup
using Backup Now, which runs the
entire workflow with associated backup
and clone actions, and Backup only out
of date sources options.
l Restore a FULL virtual machine (image-
level) backup.
l Restore a VMDK backup.
l Instant restore from a Data Domain
system.

Dell EMC Data Protection Restore Client l Perform file-level restores.

CLI l Perform FULL VM and VMDK-level

backup and restore.
l Perform file-level restores.
l Perform external proxy deployment.

System requirements
The following table lists the required components for NetWorker VMware Protection
with the VMware Backup appliance.
After upgrading to NetWorker 18.1, in order to continue using the VMware Backup
appliance to run or modify existing policies, ensure that the NetWorker server and
storage node are at the same version, and that you install or upgrade to the latest OVA
version of the VMware Backup appliance, which is version 1.5.1.7.

Note

The VMware Backup appliance is available in two capacities — a 0.5 TB and 4 TB

OVA. You only need to download one of these appliances, based on your system
requirements.

System requirements 209

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 17 NetWorker VMware Protection requirements

Component Requirements
NetWorker NetWorker 18.1 server software with NMC.
NetWorker VMware Protection only supports
the following NetWorker server architectures:
l Windows 64-bit
l Linux x86_64

VMware Backup appliance (0.5 TB OVA) l Version 1.5.1.7

l CPU: 4 * 2 GHz
l Memory: 8GB
l Disks: 3* 250 GB
l Backup storage capacity: 0.5 TB
l OS: 250 GB
l Internet Protocol: IPv4 only, IPv6 only, or
dual stack

VMware Backup appliance (4 TB OVA) l Version 1.5.1.7

l CPU: 4 * 2 GHz
l Memory: Refer to Table 20 on page 216
l Disks: 6 * 1 TB
l Backup storage capacity: 4 TB
l OS: 250 GB
l Internet Protocol: IPv4 only, IPv6 only, or
dual stack

Proxy appliance l Version 1.5.1.7

l CPU: 4 * 2 GHz
l Memory: 4 GB
l Disks: 2 disks (16 GB and 1 GB)
l Internet Protocol: IPv4 only, IPv6 only, or
dual stack

vCenter server l Version 5.5.x and 6.0.x

l Linux or Windows platform, or VC
appliance
l vSphere Web Client (the VMware website
provides information for supported web
browsers). In order to access the EMC
Backup and Recovery user interface in
the vSphere Web Client, you must enable
web browsers with Adobe Flash Player
version 11.5 or later. Since Linux platforms
only support up to Adobe Flash Player
version 11.2, only Windows platforms can

210 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 17 NetWorker VMware Protection requirements (continued)

Component Requirements

access the EMC Backup and Recovery

user interface.

ESX/ESXi server l Version 5.5.x and 6.0.x

l Changed Block Tracking (CBT) enabled

Note

Adding containers or virtual machines to a

policy will automatically enable CBT.

Data Domain l Data Domain system OS at DDOS 5.7 and

later

Note

The compatibility guide, available at

http://compatibilityguide.emc.com:
8080/CompGuideApp/, provides detailed
information on NetWorker and DD Boost
version compatibility.

l DDBoost user requires administrator

privileges

Port requirements
The NetWorker VMware Protection solution with the VMware Backup appliance
requires the ports outlined in the following tables.

Table 18 Incoming port requirements

From To Port Purpose

Data Domain VMware Backup 161 SNMP traps
appliance

NetWorker server VMware Backup 8543 NetWorker VMware

appliance Protection web
service calls to initiate
and monitor backups

NetWorker server VMware Backup 7937-9936 (RPC) Checkpoint backups

appliance

ESX server VMware Backup 902 NBD backups

appliance and external
proxy

Dell EMC Data VMware Backup 8543 File-level restore

Protection Restore appliance (FLR)
Client

Port requirements 211

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 18 Incoming port requirements (continued)

From To Port Purpose

EMC Backup and VMware Backup 8580, 8543 VMware Backup
Recovery appliance appliance
Configuration Utility configuration

vCenter server VMware Backup 7778, 7779, 8509, EMC Backup and
appliance 9443 Recovery user
interface in the
vSphere Web Client

The following diagram shows the incoming firewall port configuration with the
VMware Backup appliance.
Figure 97 Firewall configuration (VMware Backup appliance with internal proxy)

Table 19 Outgoing port requirements — with external proxies

From To Port Purpose

VMware Backup DNS 53 Name resolution
appliance

VMware Backup NetWorker server 8080 Initiate operations in

appliance NetWorker

VMware Backup NetWorker server 7937-9936 (RPC) NetWorker client

appliance and external communications
proxy

VMware Backup Data Domain 7, 22, 80, 111, 131, 163, Data Domain
appliance and external 2049, 2052 management
proxy

212 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 19 Outgoing port requirements — with external proxies (continued)

From To Port Purpose

VMware Backup vCenter 443 vCenter integration
appliance and external
proxy

VMware Backup ESX servers 443, 111, 902 Backup and recovery
appliance and operations
External Proxy

VMware Backup External proxy 28002-28009 (pre- MCS to proxy

appliance NetWorker 8.2); communications
28009 (NetWorker
8.2 and later)

External proxy VMware Backup 28001, 27000, 29000 External proxy to

appliance MCS and GSAN

The following diagram shows the outgoing firewall port configuration with the VMware
Backup appliance.
Figure 98 Firewall configuration (VMware Backup appliance with external proxy)

To communicate with the VMware Backup appliance, the NetWorker server VM web
services (nsrvmwsd) listen on port 8080 by default. Ensure that no other services,
such as HBA, use port 8080. To check port usage for 8080 outside of NetWorker:
l On Windows, run netstat -anbo | findstr 8080
l On Linux, run netstat -anp | grep 8080
l On Solaris, run lsof -i :8080
If any software other than NetWorker listens on this port, you can change the
NetWorker web services port in NMC's NetWorker Administration window.

Port requirements 213

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

To change the port, right-click the server in the Server window and select
Properties. The VMWS port field is located under the Miscellaneous tab.

Download and deploy the VMware Backup appliance

The NetWorker 18.1 release does not provide a new version of the VMware Backup
appliance. NetWorker 18.1 supports the most recent OVA and proxy version
compatible with NetWorker 9.0.x.
If you plan to continue using Networker VMware Protection with the VMware Backup
appliance in Networker 18.1, ensure that you have upgraded the VMware Backup
appliance to the NetWorker 9.0.1 version, which 1.5.1.7.

Pre-installation requirements
Before you upgrade to NetWorker 18.1, review the pre-installation requirements in this
section.

VMware Backup appliance requirements

Review the following requirements specific to using NetWorker with the VMware
Backup appliance before you install or upgrade to NetWorker 18.1.
l Ensure that the NetWorker server and storage node are at the same version, and
that you use the latest VMware Backup appliance. For example, for NetWorker
18.1, install or upgrade to the latest OVA version, 1.5.1.7.
When you upgrade NetWorker and the VMware Backup appliance, upgrade in the
following order:
n NetWorker server to NetWorker 18.1.
n NetWorker storage node to NetWorker 18.1.
n VMware Backup appliance along with external proxies to version 1.5.1.7.
l Note that you cannot create new policies and workflows with the VMware Backup
appliance in NetWorker 18.1. For new policies and workflows, you must use the
vProxy appliance.
l Ensure that the DDOS version is compatible with the NetWorker server and
VMware Backup appliance version. The VMware Backup appliance version 1.5.1.7
supports DDOS 5.7 and later.
The Data Domain Boost Compatibility Guide, available at http://
compatibilityguide.emc.com:8080/CompGuideApp/DataDomainBoost.jsp,
provides detailed information on NetWorker and DD Boost version compatibility.
l You must provide an unused IP for the VMware Backup appliance server so that it
does not conflict with the IP for another virtual machine in the environment, even
if these hosts are not physically connected.
l For registration of the VMware Backup appliance with the vCenter server, it is
recommended to use a Service account.
l Deploy the VMware Backup appliance on shared VMFS5 or higher to avoid block
size limitations.
l For better performance, it is recommended to use a dedicated datastore for the
VMware Backup appliance.

214 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l Keep the default values for annotations for the VMware Backup appliance node
and external proxy.

DNS Configuration
The DNS server plays a very important role during the VMware Backup Appliance
configuration and backup/restore operations. You must add an entry to the DNS
Server for the VMware Backup Appliance IP address and Fully Qualified Domain
Names (FQDNs).
The DNS server must support both forward and reverse lookup for the following:
l VMware Backup Appliance
l External Proxy
l NetWorker server
l Data Domain device
l vCenter and ESXi hosts

NOTICE

Failure to set up DNS properly can cause many runtime or configuration issues. Do not
manually change entries in the /etc/hosts file on the VMware Backup appliance.

You can set details for the DNS server and network IP during deployment of the
VMware Backup Appliance in the Deploy OVF Template window, as described in the
section Deploy the VMware Backup Appliance.
To confirm your DNS configuration, open a command prompt and run the following
commands from the vCenter Server.
Procedure
1. To verify DNS configuration, type the following:
nslookup VMware_Backup_Appliance_IP_address DNS_IP_address

2. To verify that the FQDN of the VMware Backup appliance resolves to the
correct IP address, type the following:
nslookup VMware_Backup_Appliance_FQDN DNS_IP_address
Ensure this is the same IP as the previous command.

3. To verify that the FQDN of the vCenter Server resolves to the correct IP
address, type the following:
nslookup vCenter_FQDN DNS_IP_address
If the nslookup commands return the proper information, then close the
command prompt; if not, correct the DNS configuration. If you configure short
names for the DNS entries, then perform additional look-ups for the short
names.

NOTICE

After deployment, check for DNS resolution (forward and reverse) from the
VMware Backup appliances and proxies for vCenter and the NetWorker hosts.

Pre-installation requirements 215

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

NTP Configuration
The VMware Backup Appliance leverages VMware Tools to synchronize time through
NTP by using the Sync guest OS time with host option by default.
On ESXi hosts, the vCenter server, and the NetWorker server, you must configure
NTP properly. Since the VMware Backup Appliance obtains the correct time through
VMware Tools, the appliance does not require configuration with NTP. However, you
must ensure that the time on the vCenter server and the ESX that hosts the VMware
Backup Appliance are as close as possible, for example, within 30 seconds of each
other. This will occur when the vCenter server is on same host as the ESX that hosts
the VMware Backup Appliance, but when this is not the case, you should configure
NTP on the VMware Backup Appliance in order to keep host times in sync.

Note

If you configure NTP directly in the EMC Backup and Recovery Configuration
Utility window, then time synchronization errors occur.

ESXi and vCenter Server documentation provides more information about configuring
NTP.

Downloading the OVAs for the VMware Backup appliance

You can obtain the VMware Backup appliance by downloading the VMware bundles,
which appear as OVAs. The OVAs are available from the same location you download
the NetWorker software.

Note

It is not recommended to configure a NetWorker 9.0.1 VMware Backup appliance with

a VMware Backup appliance earlier than NetWorker 9.0.1 in the same vCenter.

Three VMware bundles and one ISO update are available. Each fulfills a specific
requirement:
l 0.5 TB OVA
l 4 TB OVA
l EBR-Proxy OVA — download the external proxy appliance when performing more
than eight concurrent backups, or to improve performance in certain situations.
For example, you may need to deploy an external proxy to an ESX server in order
to perform hotadd backups of VMs on that server. The section Deploy an
external proxy appliance in vCenter provides the steps required to deploy an
external proxy.
l EBRUpgrade — download this ISO if you need to update the deployed VMware
Backup appliance to the latest version.
The following table provides recommendations on provisioning memory and swap
space based on the storage space in use.

Table 20 Recommended memory and swap space based on storage space utilization

Utilization Physical Memory Swap Space

less than 25% (1.0 TB) 12 GB 16 GB

less than 65% (2.5 TB) 18 GB 16 GB

216 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 20 Recommended memory and swap space based on storage space utilization (continued)

Utilization Physical Memory Swap Space

up to 100% (4.0 TB) 24 GB 16 GB

Other system requirements for the appliances are provided in System requirements.
Download the desired OVA and place in shared storage.

Proxy assignment for backup and recovery

When you have more than 8 virtual machines to protect, backup and recover
operations require the deployment of proxy virtual machines.
The OVA described in the following section has 8 internal proxies that allow you to
backup 8 virtual machines concurrently. To back up more than 8 virtual machines
concurrently, you must deploy an external proxy virtual machine that encompasses 8
internal proxies. The section Deploy external proxy appliance in vCenter describes how
to deploy the external proxy OVA.
A proxy is selected from the proxy pool based on its availability and periodically
refreshes the Proxy to datastore association.

Deploy the VMware Backup appliance

These deployment steps apply to each OVA, including the proxy OVA. Once you
download the .ova files to shared storage, open the vSphere Web Client.
Before you begin

Note

The VMware Backup appliance does not include security roll-ups. As a result, you may
also be required to manually install a security roll-up after you complete the appliance
deployment. You can access the latest version of the ESA for the security roll-up,
titled "EMC Avamar and NetWorker Security Update for Multiple Components", from
the NetWorker advisories page at https://support.emc.com/products/
1095_NetWorker/Advisories/. Scroll to the bottom of the page to view Security
Advisories. The Link to remedies section of the ESA provides instructions on how to
install the roll-up on the appliance.

To deploy the .ova:

Procedure
1. In the vSphere Web Client, navigate to Home > vCenter > Hosts and
Clusters.
2. Right-click the vCenter server and select Deploy OVF template.
3. In the Select source window, select Local file and then click Browse, as shown
in the following figure.

Proxy assignment for backup and recovery 217

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 99 Selecting the OVA to deploy in vCenter/vSphere Web Client

4. In the filetype drop-down, select OVA Packages then navigate to the directory
that contains the ova files. Select the file and then click Open.
5. On the Deploy OVF Template window, click Next.
6. On the Review Details window, click Next.
7. Accept the EULA and click Next.
8. Specify a name for the VMware Backup appliance, and then select the folder or
datacenter to which you want to deploy the appliance. Click Next.
9. Select the resource where you want to deploy the VMware Backup appliance,
then click Next.
10. Select Storage, then select the virtual disk format and click Next. It is
recommended to use thin provisioning disk format.
11. On Setup Networks, select the destination network from the drop-down, then
click Next.
12. Provide the networking properties, including the correct IP (static IP), DNS,
and so on. Verify this information is correct, otherwise the appliance will not
work. Click Next.
13. In the Ready to Complete window, ensure that the Power-on after
deployment option is selected, then click Finish.
Results
After a few minutes a screen similar to the following figure appears in the console of
the VMware Backup Appliance in vCenter.

218 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 100 EMC Backup and Recovery registration

Note

The VMware Backup appliance version 1.5.1.7 supports vCenter server versions 5.5
Update 3e, 5.5 Update 3g, 6.0 Update 2a, 6.0 Update 3b, and vCenter 6.0 Update 3d,
but only with the workaround described at https://support.emc.com/kb/489490.

Deploy external proxy appliance in vCenter

This topic describes how to deploy the proxy appliance in the vCenter.
Before you begin

Note

The external proxy appliance does not include security roll-ups. As a result, you may
also be required to manually install a security roll-up after you complete the external
proxy appliance deployment. You can access the latest version of the ESA for the
security roll-up, titled "EMC Avamar and NetWorker Security Update for Multiple
Components", from the NetWorker advisories page at https://support.emc.com/
products/1095_NetWorker/Advisories/. Scroll to the bottom of the page to view
Security Advisories. The Link to remedies section of the ESA provides instructions on
how to install the roll-up on the proxies.

Procedure
1. Launch the vSphere client and log in to the vCenter server.
The vSphere Client window appears.

2. Select File > Deploy OVF Template.

The Deploy OVF Template wizard appears.

3. In the Source screen, complete the following.

a. Select Deploy from file or URL and click Browse.
The Open dialog box appears.

Deploy external proxy appliance in vCenter 219

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

b. Select Ova files (*.ova) from the Files of Type list.

c. Browse to the proxy OVA file that was previously downloaded in
Downloading the OVAs for the VMware Backup appliance on page 216.
d. Select the proxy appliance template file and click Open.
The Open dialog box closes.
The full path to the appliance template file appears in the Deploy from file
field.

e. Click Next.
The OVF Template Details screen appears.

4. In the OVF Template Details screen, complete the following.

a. Ensure that the template information is correct.
b. Click Next.
The End User License agreement appears.

5. Accept the agreement, and then click Next.

The Name and Location screen appears.

6. In the Name and Location screen, complete the following.

a. Type a unique fully-qualified hostname in the Name field.
A Proxy can potentially have three different names:
l The name of the ESX on which the proxy runs. This is also the name
managed and visible within vCenter.
l The DNS name assigned to the proxy VM.
l The VMware Backup appliance hostname after the proxy registers and
activates with the server.
As a best practice, EMC strongly recommends that you consistently use
the same fully-qualified hostname for this proxy in all contexts.

b. Select a datacenter and folder location for this proxy in the Inventory tree.
c. Click Next.
The Host / Cluster screen appears.

7. In the Host / Cluster screen, complete the following.

a. Select an ESX server or cluster.
b. Click Next.
If you selected a cluster, the Specific Host screen appears.

8. In the Specific Host screen, complete the following.

a. Select a specific ESX server from the Host Name list.
b. Click Next.
The Resource pool screen appears.

220 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

9. In the Resource pool screen, complete the following.

a. Select a resource pool for this proxy.
b. Click Next.
The Storage screen appears.

10. In the Storage screen, complete the following.

a. Select a storage location for this proxy.
b. Click Next.
The Disk Format screen appears.

11. In the Disk Formatscreen, complete the following.

a. Accept the suggested default setting for Available Space (GB).
b. Accept the suggested default provisioning setting (Thin Provision).
c. Click Next.
The Network Mapping screen appears.

12. In the Network Mapping screen, complete the following.

a. Select a destination network from list.
b. Click Next.
The Networking Properties screen appears.

NOTICE

Proxy network settings are difficult to change after you register and activate
the Proxy. Therefore, ensure that you type the correct settings in this
screen.

13. In the Networking Properties screen, complete the following.

a. In the Default Gateway field, type the default gateway IP address for your
network.
b. Enter one or more Domain Name Server (DNS) hostnames or IP addresses in
the DNS field. Separate multiple entries with commas.
c. Enter a valid routable IP address on your network in the Network IP
Address field.
d. Type the correct netmask/prefix for your network in the Network Netmask
field.
14. Click Next.
The Ready To Complete screen appears.

15. Ensure that the information is correct.

16. Click Finish.
The Deploy OVF Template wizard closes.

17. Wait for the deployment operation to complete.

This might take several minutes.

Deploy external proxy appliance in vCenter 221

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

A confirmation message appears.

18. Click Close to dismiss the confirmation message.

Once you deploy the proxy, navigate to the console of the VM in the vSphere
client.
Figure 101 Registering proxy with the VMware Backup appliance

19. Follow the prompts to register the proxy, as shown in the figure above.
a. Press 1 to register the proxy.
b. At the Enter the EMC Backup and Recovery Appliance address prompt,
type the FQDN of the VMware Backup appliance server name.
c. At the Enter the server domain [clients]: prompt, press enter and do not
modify.
d. Provide the VMware Backup appliance password if using a non-default
password.
e. Wait for the Attempting to connect to the appliance...Connection
successful message.
20. Validate the registration in the NMC Devices tab by ensuring that the external
proxy host appears under the External Proxy Hosts column of the VMware
Backup appliance that it is registered to.

Note

When you upgrade the VMware Backup appliance, you need to deploy a new
proxy appliance. After rebooting the VMware Backup Appliance, you do not
need to re-register the external proxy.

After you deploy external Proxy hosts, each Proxy provides all of the following
capabilities:

222 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l Backup of Microsoft Windows and Linux VMs. This includes entire images or
specific drives.
l Restore of Microsoft Windows and Linux VMs. This includes entire images or
specific drives.
l Selective restore of individual folders and files to Microsoft Windows and
Linux VMs.
Although you can restore data across datacenters by using a proxy deployed in
one datacenter to restore files to a VM in another datacenter, the restores will
take noticeably longer than if the proxy and the target VM are both located in
the same datacenter. Therefore, for best performance, deploy at least one
proxy in each datacenter you are protecting.

Add DNS Entries

When you deploy a Proxy appliance, as described in Deploy external proxy appliance in
vCenter on page 219, you must specify a unique IP address and name to each proxy
VM. The vCenter server performs name resolution lookups to ensure that the host can
resolve the name and IP address. For best results, configure all required DNS entries
for the proxies you plan to deploy before performing the following steps.

Re-registering the proxy with a different server

After deploying the external proxy appliance in vCenter, if you need to re-register the
proxy with a different server perform the following.
Procedure
1. Launch the EMC Backup and Recovery Console in the vSphere Client, then
log in to the proxy.
2. Run the following command:
/usr/local/avamarclient/etc/initproxyappliance.sh start
3. Provide details for the new VMware Backup Appliance/server to re-register the
proxy.

Upgrade the VMware Backup Appliance and vCenter

The following section provides considerations and instructions for upgrading the
VMware Backup Appliance and the vCenter server to the latest version.

Upgrade the vCenter server software

NetWorker VMware Protection in NetWorker requires a minimum version of vCenter
5.5, and supports up to vCenter 6.0. The following sections provide considerations
and instructions when upgrading to a supported vCenter version.

Upgrading vCenter from version 5.1 to 5.5

The following considerations apply if upgraded your vCenter version from vCenter 5.1
to vCenter 5.5.
l If you created a non-root user (for example, test) in vCenter 5.1 using the
minimum required privileges, this user cannot log in to vCenter after you upgrade
to vCenter 5.5 because the username must now contain the full domain/path, in
the form DOMAIN\test. Use the domain that was assigned during the creation of
the user in vCenter 5.1.

Upgrade the VMware Backup Appliance and vCenter 223

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l If you deployed and configured a VMware Backup Appliance with this non-root
user test in vCenter 5.1, you must perform the following steps in order to connect
to the VMware Backup Appliance after upgrading to vCenter 5.5:
1. From a web browser, type the following URL:
https://<IP_address_VMware_Backup_appliance>:8543/ebr-configure
The EMC Backup and Recovery Configuration Utility window appears with a
tool icon from which you can select three options—Time zone, password, and
vCenter registration.
Figure 102 Select vCenter registration in the EMC Backup and Recovery Configuration
Utility

2. From the tool drop-down, select vCenter registration to unlock the vCenter
registration.
The vCenter Registration window opens
3. From the vCenter Registration window, select vCenter Configuration.
Figure 103 vCenter Configuration in the EMC Backup and Recovery Configuration
Utility

4. Change the username to DOMAIN\test, and then click Next.

5. In the Ready to Complete tab, click Finish and then reboot the appliance.

224 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Upgrading vCenter to version 6.0

If using vCenter version 5.1 or 5.5 and a VMware Backup Appliance previous to
NetWorker 9.0.1, perform the following steps to upgrade the vCenter server to
version 6.0 and the VMware Backup Appliance to the latest available version, which is
version 1.5.1.7 for NetWorker 9.0.1.

Note

In the example provided, a dedicated non-root user test has been set up with the
domain name system-domain and configured with a VMware Backup Appliance
previous to NetWorker 9.0.1. You will need to change the domain of the dedicated
non-root user from system-domain to vsphere.local by using the vSphere Web
Client, and change the vCenter username in the EMC Backup and Recovery
Configuration Utility window from test@system-domain to [email protected]
to re-register the VMware backup Appliance with vCenter.

Procedure
1. Upgrade vCenter 5.1 or vCenter 5.5 to vCenter version 6.0.
2. Open the vSphere Web Client for vCenter 6.0 with
[email protected] as the username and use the password you
set during the vCenter upgrade procedure, and perform the following:
a. In the left pane, select Administration > Users and Groups, and then click
the + sign to create a new user, test1.
b. In the Administration pane, select Roles.
c. Right-click on the role which you assigned to the user test and select Clone
to create a new role, test1role.
d. Select vCenter > Hosts and Clusters > Manage > Permissions, and then
click the + sign.
e. In the Users and Groups pane, click Add and select the user test1 with the
domain vsphere.local. Assign the role as test1Role and click Add.
3. Open the EMC Backup and Recovery Configuration Utility window as shown
in the figure above, and change the vCenter username from test@system-
domain to [email protected] to re-register the VMware backup Appliance
with vCenter, and then restart the appliance to apply the changes.
4. Upgrade the VMware Backup Appliance to version 1.5.1.7.

Upgrade the VMware Backup Appliance and vCenter 225

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Considerations prior to upgrading

When you upgrade the VMware Backup appliance, first upgrade the NetWorker
version, then upgrade the Data Domain operating system (DDOS), and then upgrade
the appliance.
Figure 104 Upgrading order for NetWorker components when upgrading the VMware Backup
appliance

Before upgrading, also review the following considerations:

l VMware Backup appliance version 1.5.1.7 is only compatible with NetWorker 9.0.1
and later.

Note

When you upgrade to NetWorker 9.0.1 and later, you must also upgrade the
VMware Backup appliance to version 1.5.1.7.
l If the internal proxy is disabled before you upgrade the Virtual Backup appliance,
the proxy is reset to enabled when you reboot the appliance. However, NMC still
shows the internal proxy's state as disabled. If this happens, run the following
command on the NetWorker server:
nsrim -X -S -h <VBA hostname> -f

Note

Do not attempt to enable the proxy manually, because it could result in NetWorker
server connection issues with the appliance.
l You only need to upgrade to DDOS 5.7 or later if you upgrade the VMware Backup
appliance to version 1.5.1.7 and plan to use Networker 18.1.
l You cannot run backup and recovery operations during an appliance upgrade.
Before performing the upgrade, ensure that you complete any policies running or
disable active policies.
l You cannot upgrade external proxies. If using a previous version of the external
proxy and you want to upgrade, you must redeploy the external proxy.

Upgrade the VMware Backup appliance

Use the following procedure to upgrade the VMware Backup appliance.
Procedure
1. Verify that the account connecting to vCenter has the required level of
permissions, particularly if a non-admin user. The section Create a customized
role provides a list of permissions.
If the permissions are not correct before the upgrade, then the upgrade process
may fail or leave the system in an inconsistent state.

226 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

2. If you made any changes to the /etc/hosts file, remove these changes. It is
not recommended to manually change entries in the /etc/hosts file on the
VMware Backup appliance.
3. Create and validate a checkpoint of the existing VMware Backup appliance by
running an integrity check.
a. Select the Configuration tab.
b. Select the Run integrity Check option, as shown in Running an integrity
check on page 273.
c. Make sure that the integrity check passes successfully.
4. Shut down the VMware Backup appliance, and then create a snapshot of the
EMC Backup and Recovery virtual machine by right-clicking the virtual machine
in the vSphere Client and selecting Snapshot > Take Snapshot..., as shown in
the following figure.
Figure 105 Take Snapshot in vSphere Client

5. Restart the appliance.

6. Verify the md5 checksum of the upgrade package.
7. Attach the ISO to the VMware Backup appliance by selecting Connect to ISO
image on local disk in the vSphere Client and selecting the ISO, as shown in
the following figure.

Upgrade the VMware Backup Appliance and vCenter 227

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 106 Connect to ISO in vSphere Client

8. Open the EMC Backup and Recovery Configuration Utility window. Post-
installation configuration on page 240 provides more information.
9. Navigate to the Upgrade tab and click Check Upgrades. The available upgrade
package appears.
10. Navigate to the Status tab to ensure all services are running.
11. Return to the Upgrade tab and click Upgrade EBR.

Note

If you want to access the EMC Backup and Recovery Configuration Utility
online help, click the Help Documentation link located on the Upgrade tab.

Figure 107 Accessing online help during upgrade

When the upgrade completes, the VMware Backup appliance shuts down
automatically.
12. Power on the VMware Backup appliance.
When you launch the EMC Backup and Recovery user interface in the
vSphere Web Client, and then connect to the upgraded appliance and navigate
to the Configuration tab, the new version appears.

228 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Note

To see the new version of the appliance in the VMware console, log out and
then log back in. The previous version is shown in the console until you do this.

13. When you complete a successful upgrade and verify that all backup and restore
functionality is working as expected, return to the vSphere Client and delete
the snapshot taken in step 4.
14. Disconnect from the ISO image used for the upgrade by unmounting or
removing the image.

Note

To upgrade a 8.2.x/9.0 VMware Backup appliance to the 9.0.1 VMware Backup

appliance version 1.5.1.7 with vCenter server versions 5.5 Update 3e, 5.5
Update 3g, 6.0 Update 2a, 6.0 Update 3b and vCenter 6.0 Update 3d, refer to
the knowledgebase article at https://support.emc.com/kb/493777.

Enable VMware View in NMC's Administration window after upgrading by creating a NSR
Hypervisor resource
When you upgrade the NetWorker server to NetWorker 18.1 and upgrade to the latest
VMware Backup appliance(s), VMware View may not appear in NMC's Administration
window until you create a NSR Hypervisor resource.
To create the NSR Hypervisor resource, download and deploy a NetWorker 9.0.1
VMware Backup Appliance (version 1.5.1.7) from vCenter, following the registration
steps described in EMC Backup and Recovery Configuration Utility on page 235, or
perform the following to manually create a NSR Hypervisor resource by using the
nsradmin program.
1. Start the NetWorker administration program by running nsradmin. Use the help
command for help, or the visual command to enter full-screen mode.
2. Type the following:

nsradmin> create type:NSR Hypervisor;name:vCenter_FQDN_or_IP

nsradmin> vi
Select type: NSR hypervisor;
name: esx3-vc1.lss.emc.com;
comment: ;
service: [VMware VirtualCenter];
endpoint: "https://esx3-vc1.lss.emc.com/sdk";
username: "ajayads\\nemo"; ======================> vCenter info
password: *******;
command: nsrvim;
proxy: nemo220-3.lss.emc.com; ============> NW Server

Note

If using NetWorker VMware Protection with the VMware Backup Appliance, ensure
that the vCenter FQDN or IP for the NSR Hypervisor resource matches what you
specified in the vCenter Registration page of the EMC Backup and Recovery
Configure window. You must use only FQDN or only IP in both instances, not a
combination of the two.

Upgrade the VMware Backup Appliance and vCenter 229

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Creating a dedicated vCenter user account and VM Backup

and Recovery role
It is strongly recommended that you set up a separate vCenter user account at the
root level of the vCenter that is strictly dedicated for use with NetWorker VMware
Protection. Use of a generic user account such as “Administrator” might make future
troubleshooting efforts difficult as it might not be clear which “Administrator” actions
are actually interfacing, or communicating, with the NetWorker server. Using a
separate vCenter user account ensures maximum clarity if it becomes necessary to
examine vCenter logs.

Create vCenter user account

Procedure
1. From a web browser, type the following:
https://<IP_address_vCenter_Server>:5480

The VMware vCenter Server Appliance login page appears.

2. Enter the vCenter root user credentials to log in.
3. In the VMware vCenter Server Appliance Console, click the Summary tab,
and then click the Stop button next to the Server service in the vCenter pane.
4. Click the SSO tab, and then select Embedded from the SSO deployment type
drop-down list.
5. Assign a password, and click Save settings.
6. Click the Summary tab, and then click the Start button next to the Server
service in the vCenter pane.
7. Log out of the session.
8. From a web browser, enter the following to connect to the vSphere Web Client:
https://<IP_address_vCenter_Server>:9443/vSphere-client/

9. Login as user [email protected] with the password you created in

step 5.
10. Navigate to Home > Administration > SSO Users and Groups.
11. On the Users tab, click the green +.
The New User window appears.
12. In the Username field, specify a username (for example, VM Backup and
Recovery).
13. In the Password and Confirm Password fields, specify a password.
You can leave the First name, last name and password fields blank.
14. Click OK.

230 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Create a customized role

Procedure
1. In the vSphere Web Client, open Administration > Role Manager and click on
the green +.
The Create Role dialog appears.

2. Type the name of this role (for example, Admin1).

3. Select all the privileges listed in the following table and click OK. This vCenter
user account must have these privileges at a minimum.

Table 21 Minimum required vCenter user account privileges

Setting vCenter 5.5 and later required

privileges
Alarms l Create alarm
l Modify alarm

Datastore l Allocate space

l Browse datastore
l Configure datastore
l Low level file operations
l Move datastore
l Remove datastore
l Remove file
l Rename datastore

Extension l Register extension

l Unregister extension
l Update extension

Folder l Create folder

Global l Cancel task

l Disable methods
l Enable methods
l Licenses
l Log event
l Manage custom attributes
l Settings
l Set custom attribute

Host l Configuration > Storage partition

configuration

Create a customized role 231

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 21 Minimum required vCenter user account privileges (continued)

Setting vCenter 5.5 and later required

privileges

Note

Not applicable to vCenter 5.5.

Network l Assign network

l Configure

Resource l Assign virtual machine to resource pool

l Migrate powered off virtual machine
l Migrate powered on virtual machine

Sessions l Validate session

Tasks l Create task

l Update task

vApp l Export
l Import
l vApp application configuration

Virtual Machine

Configuration l Add existing disk

l Add new disk
l Add or remove device
l Advanced
l Change CPU count
l Change resource
l Configure managed by
l Disk change tracking
l Disk Lease
l Extend virtual disk
l Host USB device
l Memory
l Modify device settings
l Raw device
l Reload from path
l Remove disk
l Rename
l Reset guest information
l Set annotation

232 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 21 Minimum required vCenter user account privileges (continued)

Setting vCenter 5.5 and later required

privileges

l Settings
l Swapfile placement
l Upgrade virtual machine compatibility

Guest Operations l Guest operation modifications

l Guest operation program execution
l Guest operation queries

Interactions l Configure CD media

l Console interaction
l Device Connection
l Guest operating system management by
VIX API
l Power off
l Power on
l Reset
l VMware Tools install

Inventory l Create new

l Register
l Remove
l Unregister

Provisioning l Allow disk access

l Allow read-only disk access
l Allow virtual machine download
l Mark as Template

Snapshot Management l Create snapshot

l Remove Snapshot
l Revert to snapshot

vSphere Client user accounts

Before you can use the vCenter user account with NetWorker VMware Protection, or
before you can use the Single Sign-on (SSO) admin user with the vProxy appliance,

vSphere Client user accounts 233

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

you must add these users as administrator on the vCenter root node. Users who
inherit permissions from group roles are not valid.

Note

In high-security environments, you can restrict the vCenter user account permissions
required to configure and administer the vProxy appliance. Table 9 on page 60
provides the account permission categories.

The following steps allow you to configure a VM Backup and Recovery user or SSO
admin user by using the vSphere Web Client.
Procedure
1. From a web browser, access the vSphere Web Client using the following URL:
https://<Ip_address_vCenter_server>:9443/vsphere-client/

2. Log in with administrative rights.

3. In the left panel of the vSphere Web Client window, select vCenter > Hosts
and Clusters.
Figure 108 Hosts and Clusters in the vSphere Web Client

4. Select the Manage tab and then click Permissions.

Note

When assigning permissions, the vSphere Web Client places the curser in the
location last used. Depending on what level was selected the last time you used
this window, permissions might not get applied to the root level of the vCenter.
For example, if the last item you selected in this window was Cluster Name,
permissions will be assigned at the Cluster level. Review carefully to ensure that
permissions get assigned at the root level of the vCenter.

5. Click the Add permission ( ) icon.

The Add Permission dialog box opens.

234 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

6. In the Users and Groups pane, click Add....

The Select Users/Groups dialog box appears.

7. From the Domain drop-down list, select domain, server, or SYSTEM-DOMAIN.

8. Select the user that will administer VM Backup and Recovery, or the SSO admin
user, and then click Add.
If the VM Backup and Recovery user belongs to a domain account, the account
appears in the format “SYSTEM-DOMAIN\admin” format. If the user name
appears in the format “admin@SYSTEM-DOMAIN”, then tasks related to the
backup job may not appear on the Running tab of the Recent Tasks window.

9. Click OK.
10. From the Assigned Role drop-down list, select the role you created.
11. Confirm that the Propagate to children box is checked.
12. Click OK.

Restrict mapping of datastores

You can perform VM backups by using one of two methods:
l Hotadd—The VMware Backup Appliance or External proxy directly mounts the
VM's hard disk to read the backup data. This mode requires that the proxy has
direct access to the datastore of the VM that you want to back up.
l NBD—The VMware Backup Appliance or External proxy will connect to the ESX
server that the VM is running on over the IP network, and data will be transferred
over the IP network to the proxy. As a result, NBD mode is typically slower than
hotadd mode.
By default, hotadd mode is used. If the proxy does not have direct access to the
datastore that the VM is running on, it will fall back to using NBD mode to improve the
chances of obtaining a successful backup.
In certain environments, you may want to prevent fallback to NBD backups to ensure
no backup traffic occurs across the IP network. In such cases, you can configure your
system to use an alternate mode where backup jobs will only be given to proxies that
have the ability to perform a hotadd backup of the VM. When configuring this mode,
you must deploy an external proxy on an ESX server that has access to the datastore
that the VM resides on. Failure to do so results in the backup failing with the error “No
Proxy.”
To configure this mode of operation, you can select the option in the NSR VBA Server
Properties window, described in the section VMware Backup Appliance monitoring and
properties on page 251.

EMC Backup and Recovery Configuration Utility

Complete the VMware Backup Appliance registration and configuration by using the
EMC Backup and Recovery Configuration Utility window.
Procedure
1. Open an internet browser and type the URL to connect to the VMware Backup
Appliance. The URL will be similar to the following:

http://VMware Backup appliance IP:8580/ebr-configure

Restrict mapping of datastores 235

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

The EMC Backup and Recovery Configuration Utility window opens.

Note

The EMC Backup and Recovery Configuration Utility requires Adobe Flash
Player version 11.5 or later. If you do not have the appropriate version of Adobe
Flash Player installed, a message appears with a link to download it. If you are
still unable to connect after installing Adobe Flash Player, then check the
network configuration (IP address, DNS, and so on) by logging into the VMware
Backup Appliance registration screen. If any of the network information was
incorrectly entered, you must re-deploy.

2. Log in with the userid root, and create a password that is a minimum of 9
characters long and contains a combination of one more more upper and lower-
case letters, one or more numbers from 0-9, and at least one special character.

Note

You can use the previous default password 8RttoTriz or a password without
special characters only if you apply a hotfix to the OVA version 1.5.1.7 prior to
running the EMC Backup and Recovery Configuration Utility. The hotfix is
available in the same download location as the OVA.

The Welcome page displays.

Figure 109 Welcome configuration page

3. Click Next.
The Network Settings page displays.

236 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 110 Network Settings configuration page

4. Verify the network settings, and click Next.

The Time Zone page displays.
Figure 111 Time Zone configuration page

5. Set the time zone to match that of the vCenter appliance, and click Next.

Note

If the time zone does not match that of the appliance, you may encounter
issues connecting with EMC Backup and Recovery from the vCenter. The
default time zone for vCenter is UTC.

The EBR Credentials page displays.

EMC Backup and Recovery Configuration Utility 237

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 112 EBR Credentials configuration page

6. Specify a new EMC Backup and Recovery password for the root account, and
click Next.
The vCenter Registration page displays.
Figure 113 vCenter Registration configuration page

7. Type the details required to connect to the appliance.

Note

When you use the FQDN or IP to register the vCenter server in this window and
with the NetWorker server, ensure that you specify only the FQDN or only the
IP in both instances, not a combination of the two.

8. Click Test connection.

You should see a message that the connection test completed successfully.
9. Ensure that Use vCenter for SSO authentication remains selected , and click
Next.

Note

If the vCenter server host is different from the vSphere web server host, use
admin@system/domain as the user name along with the appropriate password.

238 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

The NetWorker registration page displays.

Figure 114 NetWorker registration configuration page

10. Type the details required to connect to the NetWorker server:

l NetWorker username = VMUser (default).
l NetWorker password = changeme (default)
l NetWorker hostname: type the IP address or FQDN of the NetWorker
server
l NetWorker port = 8080 (default)

Note

To change the default name VMUser, in NMC go to NetWorker

Administration > NetWorker server properties > Miscellaneous, and
change both the user name and password. Ensure that when you change the
user name and password in NMC that you specify the new values in the
NetWorker registration page.

Note

If you are performing a disaster recover, select the Override NetWorker

registration check option if the VMware Backup Appliance has registered to
the NetWorker server.

11. Click Test NetWorker connection.

You should see a message that the connection test completed successfully.
12. Click Next.
The Complete page appears.

EMC Backup and Recovery Configuration Utility 239

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 115 Complete configuration page

13. Click Complete and Finish.

Configuration begins, and the progress is shown.
Figure 116 Complete progress page

Post-installation configuration
You can confirm that the installation process successfully registered and configured
the VMware Backup Appliance in NetWorker.
Procedure
1. Ensure that the Log window in NMC's Administration window displays the
following information:
NetWorker server, 'server_name' registration succeeded for
VMware Backup Appliance VBA_hostname
2. Log in to the EMC Backup and Recovery Configuration Utility window at the
following URL by using the new EMC Backup and Recovery password that you
defined during configuration:
http://VMware_Backup_appliance_IP:8580/ebr-configure

You should see the following window, in which you can verify information about
your configuration and ensure that required services are running. You can also
see a summary of storage and capacity usage, and perform tasks such as rolling

240 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

back the VMware Backup appliance to a known validated checkpoint, upgrading

the appliance, executing emergency restore, editing Networker configuration,
and downloading client and VMware Backup appliance logs.
Figure 117 Post VMware Backup Appliance configuration

Starting and stopping services

The Configuration tab lists all of the services required by EMC Backup and Recovery
and the current status of each service. The following table describes these services.

Table 22 Description of services running on the VMware Backup Appliance

Service Description
Core Comprise the backup engine of the appliance.
If these services are disabled no backup jobs
(either scheduled or “on demand”) will run,
and no restore activities can be initiated.

Management Stop these services only under the direction

of technical support.

Maintenance services Perform maintenance tasks (for example,

evaluating whether retention periods of
backups have expired). Services will start up
at the Start Time for the first maintenance
window after 24 hours have elapsed. For
example, if the system was deployed at
10.20am on Thursday, then 24 hours after this
would be 10.20am on Friday. The next
maintenance window would then start at 8am
on Saturday. The maintenance window is
scheduled by default to start at 8am each day.
You can make changes to the default
maintenance window by using the command
line.

Starting and stopping services 241

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 22 Description of services running on the VMware Backup Appliance (continued)

Service Description
Backup Scheduler Allow mounting of backups for file-level
restore operations.

File level restore Support the management of file-level restore

operations.

Backup Recovery Support the management of backup and

recovery operations.

To stop a service, click Stop next to the service on the Configuration tab of EMC
Backup and Recovery Configuration Utility window. In general, you should only stop
running services under the direction of Technical Support.
If you stop a service, you can attempt to restart it by clicking Start. In some cases,
additional troubleshooting steps may be required for the service to work properly.

Note

When any service stops running, the action triggers an alarm on the vCenter server.
When the service restarts, vCenter clears the alarm. A delay of up to 10 minutes can
occur before vCenter clears or triggers an alarm.

Click the refresh icon to update the status display.

If all services are stopped, then start the services in the following order:
1. Core
2. Management
3. Maintenance
4. Backup Scheduler
5. File Level Restore
6. Backup Recovery

Changing the maintenance window

Use the following procedure if you want to change the backup schedule (maintenance
window) settings. This example demonstrates how to change the maintenance
window from the default (8 PM to 8 AM the following day) to a custom value (6 PM
to 2 PM the following day):
Procedure
1. Check the current schedule by running the following from the command line:
admin@ebr169:/usr/local/avamar/bin/>: status.dpn

The end of the output indicates the current settings for backup window and
maintenance window start times.
Next backup window start time: Sat Sep 28 20:00:00 2013
IST
Next maintenance window start time: Sat Sep 28 08:00:00
2013 IST

242 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

2. Change the backup start time (in format HHMM) and duration (in format
HHMM) by running:

admin@ebr169:/usr/local/avamar/bin/>: avmaint sched window --

backup-start=1800 --backup-duration=2000 --ava

3. Verify the change by running:

admin@ebr169:/usr/local/avamar/bin/>: status.dpn

The end of the output indicates the new backup window and maintenance
window start times:
Next backup window start time: Sat Sep 28 18:00:00 2013
IST
Next maintenance window start time: Sat Sep 28 14:00:00
2013 IST

Adding or swapping a NIC for VMXNET 3 on the VMware

Backup appliance or external proxy
The following section describes how to set up a virtual network interface card (vNIC)
of type VMXNET 3 for the VMware Backup appliance and/or external proxy appliance.
Before you begin
This procedure is required for custom setup using dual NIC as described in the section
Dual vNIC Setup and configuration requirements, but is otherwise optional for most
VMware Backup appliances and external proxy appliances.
Performing this setup requires that you download and deploy the VMware Backup
appliance or external proxy appliance, and then use the following steps to configure
the appliance before the steps outlined in the section EMC Backup and Recovery
Configure window setup. When you deploy the VMware Backup Appliance, configure
the vNIC, or eth0, with an IP address from the production subnet/VLAN.
Procedure
1. Log in to the VMware Backup appliance console in the vSphere Client.
2. Right-click the VMware Backup appliance and select Power > Shutdown
Guest.
3. Add the second NIC to the VMware Backup Appliance:
a. Right click the VMware Backup appliance, and then select Edit Settings.
The Virtual Machine Properties window appears.

Adding or swapping a NIC for VMXNET 3 on the VMware Backup appliance or external proxy 243
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 118 Swap network for NICs in the Virtual Machine Properties window

b. (Optional when swapping NIC) In the Hardware tab, select Network

adapter 1 in the list, and then click Remove.
c. In the Hardware tab, click Add.
The Add Hardware wizard opens.
d. In the Device Type page, select Ethernet Adapter and click Next.
e. In the NetWork Type page, change the value in the Adapter Type field to
VMXNET 3, and assign this vNIC to the appropriate virtual machine port
group. Select the Connect at power on checkbox if it is not selected.

244 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 119 Change Adapter Type

f. Select the appropriate virtual machine port group for the production
network/VLAN, and then click Next.
g. In the Ready to Complete page, verify the information and then click
Finish.
4. Right click the VMware Backup appliance and select Power > Power On.
5. Configure the second NIC on the VMware Backup Appliance:
a. After you power on the VMware Backup appliance, log in as root to the
VMware Backup appliance Console by using the vSphere Client.
b. Type yast2 to invoke the YaST configuration tool.
c. Select Network Devices and press Enter.
The Network Devices dialog appears.
d. Select Network Settings and press Enter.
The Network Settings dialog appears.
e. In the Overview tab, select the Second Ethernet Adapter labeled eth1.
f. Use the tab key to select Edit and press Enter.
g. From the Network Card Setup, use the tab key to access Statically
assigned IP Address and select using the spacebar. Use the tab key to
select IP Address and enter the IP Address, the Subnet Mask, and the host
name of the VMware Backup appliance for the backup network.
h. Use the tab key to select Edit, and then press Enter.
i. (Optional when setting up second NIC) From Network Settings, use the tab
key to select Overview. Use the right-arrow key to select Hostname/DNS.
Use the tab key to select and then specify the following fields:
l Host name
l Domain name for the production network

Adding or swapping a NIC for VMXNET 3 on the VMware Backup appliance or external proxy 245
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l Policy for DNS configuration

l Name Server 1 for production network
l Name Server 2 for backup network
l Domain Search for both production and backup network.

When setting up a second NIC, carefully review the following sections

including operating system routes since you may need to be define these
routes as custom routes.

j. From Network Settings, use the tab key to select Hostname/DNS.Use the
right-arrow key to select Routing, and update the routing table by setting
the Default Gateway to the gateway/address for the production network, if
not already set, as shown in the following figure.
Figure 120 Routing table with production network gateway

k. Use the tab key to select OK, and then press Enter.
l. Use the tab key to select Quit, and then press Enter.
6. (Optional) If setting up vNIC on the external proxy, follow the instructions in
the section Re-registering the proxy with a different server.

Dual NIC support

This section outlines NetWorker support for enabling the VMware Backup appliance
and external proxy appliance to support dual vNIC.
Enabling a second vNIC on the VMware Backup appliance and the external proxy
appliance can provide the following benefits:
l You can separate the backup data traffic going to the back-end from the
production network so that backups do not negatively impact performance in your
environment.
l You can use a separate private or isolated physical network infrastructure for your
backup network and send the backup data in this isolated network unencrypted,
leading to performance gains.

246 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l You can dedicate a NIC to backup traffic so as not to impact production

performance if using an older host with a slower physical NIC.

Dual vNIC setup and configuration requirements

Along with the requirements specified in the sections Pre-installation requirements
and Download and deploy the VMware Backup Appliances, the VMware Backup
Appliance and external proxy appliance require the following:
l Manually add a new vNIC of type VMXNET 3 according to the instruction in step
3b of the section "Adding or swapping a NIC on the VMware Backup appliance or
external proxy."
l Configure the two vNICs with two separate and unique subnets in order to
facilitate the direction of production traffic (which includes vCenter Server traffic,
VMTools requests used by file-level restore, and so on) on the first vNIC. All
backup traffic will flow out of the second vNIC on the backup network. Further
details for VMware Backup appliance NIC connectivity are provided in the bullets
below.
l Internal proxies must be disabled.
l In order to use Instant Access restore, which will mount a NFS Data-store on the
ESX, the backup network on the ESX may require a VMkernel port configured.
l Proxies with multiple NICs rely on the operating system routes and require reliable
bi-directional communications with the respective subnets on which the NICs are
configured with Data Domain systems.

Note

You may be required to define operating system routes as custom routes.

l The VMware Backup Appliance and external proxy appliance must have eth0
belong to the production network and contained within the same subnet which
includes your vCenter Server eth0. Also, for the VMware Backup Appliance and
external proxy appliance, eth1 must belong to the backup network and contained
within the same subnet as the Data Domain device.
Figure 121 Sample backup and production network traffic flow

Dual vNIC setup and configuration requirements 247

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

You can use a non-routable private address space for the subnet used for the backup
traffic/data, providing that:
l All devices/vNICs using a private IP address exist on the same physical switch, and
l There is a DNS server on the non-routed private network so that the proxies can
perform a reverse lookup for its host name.

Note

A private address space-based network is an optional example and not a requirement.

Verify vNIC connectivity

You can verify that the vNIC is associated to the correct network by running a test
using ping or traceroute against the IP of the NetWorker server and/or vCenter and
other required componenets. If the IP is not reachable, you may need to swap the
network for NICs.
1. Right-click the VMware Backup appliance and select Edit Settings.
2. in the Hardware tab of the Virtual Machine Properties window, select Network
adaptor and Network connection on the right of the screen.
3. In the Network connection page, select the correct network label.
4. Click OK to complete the configuration change.
For systems with swapped NICs or dual vNIC configurations, you can use the
proxycp.jar command line utility on the VMware Backup appliance to test
connectivity.
To download the proxycp.jar command line utility:
1. Log into the VMware Backup appliance by using the vSphere Client or a putty
session.
2. If required, run sudo su - to switch to the root user.
3. In a command prompt, cd to usr/local/avamar/bin/.
4. Run the following command:

curl -O ftp://avamar_ftp:[email protected]/software/scripts/
proxycp.jar

For sites where direct download using curl is unavailable, use WinSCP to transfer
the script to the VMware Backup appliance or external proxy.
5. Change the permissions on proxycp.jar:

chmod 755 /usr/local/avamar/bin/proxycp.jar

After downloading proxycp.jar, you can use the following command tools to test
connectivity:
l proxycp.jar --vctest --dryrun—Tests connectivity to vCenter and
returns many details of the vCenter.
l proxycp.jar --testconn—connects to vCenter to perform tests at set
intervals, similar to "ping tests".
l proxycp.jar --testwebservice—Tests connectivity to the Avamar MC
SDK.

248 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l proxycp.jar --portcheck [--timeout <Num> ] - Tests proxy

connectivity to vCenter by discovering all nodes and hosts in the environment and
then checking connectivity of each proxy to every single ESX host. Also checks
for Data Domain in the environment and checks connectivity from the proxy. If
running in a slower environment you can change the timeout value from the
default of 10 seconds to 60 seconds.
Dual NIC configuration, and particularly operating system routes, can be very complex
and require careful planning by the administrator. When complete the setup and
verified working functionality of the configuration, make note of the configuration
details including NIC Type, IPs, operating system routes and any other custom
setttings since these may be required if he has to re-create the OVA for situations like
proxy upgrades, storage failures, etc

Backing up the VMware environment using NMC

Once the OVA for the VMware Backup appliance has been successfully deployed, you
can run an existing VMware protection policy with a workflow for VMware backup
within the NMC NetWorker Administration window, and assign virtual machines and
VMDKs to the workflows for backup and recovery.

Setting user privileges for the root user in the NetWorker server
Before you access the VMware Protection solution in NMC to create and assign
policies, you must assign the appropriate user privileges to the root user in a user
group of the NetWorker server.
Procedure
1. Run nsradmin from a Windows command line or UNIX terminal.
2. Type the following command:
create type:NSR usergroup; name:user defined user group

3. When prompted with the question "Create?", type Y, and then exit from
nsradmin.
4. From NMC, navigate to NetWorker Administration > Server > User Groups.
5. Select the created user group for the root user and type the following in the
Users field:
username@VBA node
where username is the name of a user with root privileges.

6. Assign the following privileges in the Privileges field:

l Monitor NetWorker
l View Application Settings.

Backing up the VMware environment using NMC 249

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Accessing VMware Protection in NMC

When you connect to the NMC server, the NMC GUI's Enterprise window appears.
Figure 122 NMC Enterprise window

Procedure
1. In the left panel of the Enterprise window, select the appropriate server.
2. Right-click the server, and select Launch Application.
The Administration window opens.
Figure 123 Protection window in the Administration window

You can access many of the options for the VMware Protection solution in the
Protection window.

250 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

VMware Backup Appliance monitoring and properties

In the Devices window, select VMware Backup Appliances and the available VMware
Backup Appliances appear in the right pane. From the right pane, you can monitor the
state of the VMware Backup appliance, as shown in the following figure.
Figure 124 VMware Backup appliance health monitoring in the Devices window

To view more VMware Backup Appliance related properties, right-click an appliance

resource and select Properties, or double-click an appliance. The NSR VBA Server
Properties window displays.
Figure 125 NSR VBA Server Properties window

NetWorker automatically retrieves information about the VMware Backup Appliance,

including the following details and health information:
l vCenter host
l Policies pushed to the VMware Backup Appliance
l List of External proxy hosts

VMware Backup Appliance monitoring and properties 251

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l Total internal storage capacity

l Used internal storage capacity
l Last Validated checkpoint
l Online/Offline
l Configuration Error
l State
In addition to the fields that NetWorker populates automatically based on the current
settings, the NSR VBA Server Properties window includes the following fields that
you can edit:
l VBA Internal Proxies—When set to Enabled, the internal proxy is active and
available. Setting to Disabled shuts down the internal proxies and limits proxy
availability to the external proxy, which is required for EXT4 and LVM support.
This is set to Enabled by default.
l VBA Adhoc Backups—When set to Enabled, this setting allows you to run a
workflow that includes any associated backup and clone actions immediately from
the Administration window or the vSphere Web Client. When set to Disabled,
you can only perform adhoc backups from the Administration window, and the
Backup Now functionality in the vSphere Web Client is not available. This is set
to Enabled by default.
l VBA Restrict Transport Mode to Hotadd Only—When set to Enabled,
NetWorker will use only Hotadd transport mode for policy backups, and fallback to
NBD mode (backups over IP) will not occur, even if Hotadd mode is not available.
When set to Disabled, NetWorker will use Hotadd mode, and fallback to NBD
mode if Hotadd mode is not available. This is set to Disabled by default.

Note

When you restrict the transport mode to Hotadd only, backups will fail for any VM
that does not meet the Hotadd criteria as outlined in the VMware knowledgebase
article 2048138. When such a failure occurs, the backup policy only reports that
the backup was “Interrupted.” The correct status displays when you run the
following command:

mccli activity show | grep Eligible

Output similar to the following displays:

9139905687058209 No Eligible Proxies 0 2014-05-03 00:24 IST

00h:00m:00s 2014-05-03 00:24 IST On-Demand Backup 0 bytes 0%
VM-Local

VMware data protection policies for the VMware Backup appliance in NMC
You can use the NMC NetWorker Administration window to schedule a backup of
existing VMware protection policies for the VMware Backup appliance that were

252 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

created in NetWorker 9.0.x releases, or to modify what contents are included in the
existing policies.

Note

NetWorker 18.1 does not support the creation of new VMware Backup appliance
policies. For the creation of new policies, use the vProxy appliance.

The sections Overview of data protection policies and Default data protection policies
provide more information about protection policies in NMC.

Starting, stopping, and restarting policies

The workflows in a policy can run automatically, based on a schedule. You can also
manually start, stop, and restart specific workflows by using the the NMC NetWorker
Administration Monitoring window.
You can restart any failed or canceled workflow. Note, however, that the restart must
occur within the restart window that you specified for the workflow. Additionally, for a
VMware backup, if you cancel a workflow from NetWorker Administration and then
want to restart the backup, ensure that you restart the workflow from the NetWorker
Administration window. If a workflow that was started from NetWorker
Administration is restarted from the vSphere Web Client, the backup fails.
Procedure
1. In the Monitoring window, select the workflow or actions.
2. Right-click and then select Start, Stop, or Restart.
A confirmation message appears.

Note

You cannot stop, restart, or start individual actions.

3. Click Yes.

VMware data protection policies for the VMware Backup appliance in NMC 253
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Visual representation of VMware policy and associated actions

A visual representation of the VMware backup policy with its associated workflow and
actions appears in the lower panel of the Protection window.
Figure 126 VMware protection policy in the Protection window

The Media window displays the save sets contained within the policy. If the save sets
are additionally part of an application-consistent policy, a green check mark appears in
the VM App Consistent column.
Figure 127 VMware protection policy save sets in Media window

254 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

VMware View in NMC

The VMware view provides an overview of the vCenter environment.
After detecting VMware environments, the Administration window provides a visual
representation of these environments when you select VMware View in the left pane
of the Protection window. Using VMware View, you can also assign policies.
The following sections describe the options that are available in VMware View.

Note

After upgrading to NetWorker 18.1, VMware View may not be visible.

Map view of the VMware environment

When you expand VMware View, a hierarchical display of the VMware environment
appears. The following containers display:
l vCenters
l DataCenters within the vCenter
l Clusters within the DataCenter
l ESX servers
l vApps
l Resource Pools
l Folders
You can use several operations to navigate within the map view:
l To zoom in and out of the map view, select the zoom icons on the map view icon
bar or click on the right details pane and scroll with the mouse wheel. You can also
click the Zoom Area button to select an area to zoom into, or click the Fit
Content button to fit the entire display into the right details pane. These
operations are also available when you right-click the details pane.
l To move the graphical display, left-click in the details pane and drag the mouse
cursor.
l To expand or collapse any container in the map view to display or hide the child
elements associated with the container, double-click the container.
l To display an overview of the map view, select the Overview tab within the
Overview pane. The overview of the map view is particularly useful for large maps
and allows you to quickly drill down to specific areas in the map.
l To limit items displayed and search for specific items in the map view, use the
Filter VM by and Show functions, available from the Filter tab within the
Overview pane.
When you click on any container, the hierarchical tree provides a detailed map view of
that container and all of its children. For example, select the top level virtualization
node to display a complete view of your VMware environment across all configured
vCenters, or select an individual ESX server or Cluster in the hierarchy to display the
resource pool with all child elements associated with that ESX server or Cluster
including VMs, VMDKs, VMware Backup Appliances, external proxies, along with any
associated VMware backup policies to the right of these containers.
Lines connect each child element to the parent element, with child elements
proceeding hierarchically from left to right in the display, as shown in the following
figure.

VMware data protection policies for the VMware Backup appliance in NMC 255
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 128 Map view of VMware environment in NMC

To refine items displayed in the right details pane, select containers in the
Virtualization node hierarchy in the left pane. For example, if an individual Cluster is
selected in the Virtualization node, only child elements associated with that Cluster
display.

256 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 129 Cluster with child elements in VMware View

To filter the visible items to show only protected VMs, unprotected VMs, or
overprotected VMs, click the links located above the right pane, as shown in the
following figure.
Figure 130 Filtering results in VMware View

VMware data protection policies for the VMware Backup appliance in NMC 257
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table view of the VMware environment

To switch to a view of the VMware environment in table form, right-click anywhere in
the details pane and select Table. The Table view functions like other table views in
the Administration window.

Note

Table view only displays information for virtual machines. It does not show any details
about VMDKs. You must use Map view to display those details.

Figure 131 VMware table view

The filtering function works the same in Table view as in Map view. Links provided
above the details pane allow you to display only overprotected virtual machines,
unprotected virtual machines, or all virtual machines in the environment. The
NetWorker Administration Guide provides general information on using tables in the
Administration window.

Note

In Table view, the Host field contains an undefined value for virtual machines or
containers that are part of a cluster. The Map view provides a link to the cluster.

Assigning groups within VMware View

You can assign groups at any level, for example, you can assign a group to the entire
datacenter, a cluster, a resource pool, a virtual machine, or even a VMDK by using
VMware View.
Procedure
1. Right-click on any container, or expand the container, and then right-click on an
element within VMware View.

258 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

2. Select Add to Group.

The available groups display, as shown in the following figure.
Figure 132 Add group in VMware View

3. Select a group, and click OK.

VMware View refreshes and displays the new association.
4. To assign a group at the VMDK level, expand a virtual machine, right-click the
VMDK that you want to associate to the group, and select Add to Group.

Overprotected and unprotected virtual machines in VMware View

NMC uses a warning icon within VMware View to show virtual machines that are
overprotected (when a particular virtual machine is protected by two different groups,
or two different VMware Backup appliances) or unprotected (when there are no
groups assigned to protect a particular virtual machine or container).
Overprotection can only occur when you use the EMC Backup and Recovery user
interface in the vSphere Web Client and NMC to assign groups to virtual machines/
VMDKs. When overprotection occurs, you can remove a group. Right-click the object
and select Remove Group. When you unselect the additional group in the resulting
dialog, the warning sign disappears.
You can use the filter links, as shown in Figure 130 on page 257, to narrow your view
to only overprotected or only unprotected virtual machines.

Assigning a group to a disconnected ESXi server in VMware View

When you disconnect an ESXi host from the vCenter server, the ESXi is removed from
the EMC Backup and Recovery user interface in the vSphere Web Client, but still
appears in NMC's VMware View. You can assign a group to an ESX host that is
disconnected from the vCenter server, however, if you start the group, the group will
remain in “interrupted” state until you connect the disconnected ESXi back to the
vCenter server and run the group again.

Note

Disconnecting an ESXi server from a vCenter server only temporarily disconnects the
server and does not remove the server. To permanently remove the ESXi server from
the vCenter inventory, use the Remove option from vCenter.

VMware data protection policies for the VMware Backup appliance in NMC 259
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Decommissioning the VMware Backup Appliance in NMC

Decommissioning should be done only with the help of EMC Support.

Managing the VMware environment using the vSphere Web

Client
The vSphere Web Client provides access to the EMC Backup and Recovery user
interface. The EMC Backup and Recovery user interface functions as a plug-in within
the vSphere Web Client that connects to the VMware Backup Appliance, allowing you
to perform several operations including:
l Assign VMs/VMDKs to policies created in NMC

Note

Since this same functionality, described in the section Assigning groups within
VMware View on page 258, is available within NMC, EMC recommends that you
only use NMC to assign VMs/VMDKs to policies.
l Backups (Ad-hoc VM backups, also known as Backup Now and Backup only out
of date sources)
l Recoveries (FULLVM image-level recoveries, VMDK recoveries, and instant
access recovery)
l View reports and log files for policies run
l Configuration options such as email notifications

Note

You cannot use the VMware Backup Appliance without a vCenter Server. In linked
mode, the appliance works only with the associated vCenter server.

Benefits of EMC Backup and Recovery user interface in the vSphere Web
Client
The EMC Backup and Recovery user interface provides the following benefits:
l Provides fast and efficient data protection for all of your virtual machines/VMDKs,
even those migrated between ESX hosts.
l Significantly reduces disk space consumed by backup data by using patented
variable-length deduplication with every backup operation. The section
Deduplication store benefits on page 261 provides more information.
l Reduces the cost of backing up virtual machines and minimizes the backup
window by using Changed Block Tracking (CBT) and virtual machine snapshots.
l Allows for easy backups without the need for third-party agents installed in each
virtual machine.
l Uses a simple, straight-forward installation as an integrated component within
EMC Backup and Recovery, which is managed by a web portal.
l Provides direct access to EMC Backup and Recovery configuration integrated into
the vSphere Web Client.

260 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l Protects backups with checkpoint and rollback mechanisms.

l Provides simplified recovery of Windows and Linux files with end-user initiated file
level recoveries from a web-based interface.

Deduplication store benefits

Enterprise data is highly redundant, with identical files or data stored within and
across systems. For example, OS files or documents sent to multiple recipients. Edited
files also have tremendous redundancy with previous versions. Traditional backup
methods magnify this by storing all of the redundant data repeatedly. EMC Backup
and Recovery uses a patented deduplication technology to eliminate redundancy at
both the file and the subfile data segment level.

Variable vs. Fixed-Length Data Segments

A key factor in eliminating redundant data at a segment (or subfile) level is the method
used to determine the segment size. Snapshots and some deduplication technologies
commonly use fixed-block or fixed-length segments to determine the segment size.
Unfortunately, even small changes to a dataset, for example, inserting data at the
beginning of a file, can change all fixed-length segments in a dataset, despite the fact
that very little of the dataset has been changed. EMC Backup and Recovery uses an
intelligent variable-length method to determine the segment size, which examines the
data to determine logical boundary points and increases efficiency.

Logical Segment Determination

EMC Backup and Recovery uses a patented method to determine the segment size
that yields optimal efficiency across all systems. The algorithm analyzes the binary
structure of a data set to determine the context-dependent segment boundaries.
Variable-length segments average 24 KB in size and EMC Backup and Recovery
further compresses the segments to an average size of 12 KB.
EMC Backup and Recovery works for all file types and sizes and intelligently
deduplicates the data by analyzing the binary structure within the VMDK files.

Image-level Backup and Restore

EMC Backup and Recovery creates VADP-integrated image-level backups. This
integration offloads the backup processing overhead from the virtual machine to the
EMC Backup and Recovery appliance. The EMC Backup and Recovery appliance
communicates with the vCenter Server to make a snapshot of a virtual
machine’s .vmdk files. Deduplication takes place within the appliance using a patented
variable-length deduplication technology.
To support the large scale and continually expanding size of many environments, each
EMC Backup and Recovery appliance can simultaneously back up to eight virtual
machines. All virtual machines must belong to the vCenter that is dedicated to EMC
Backup and Recovery.
To increase the efficiency of image-level backups, EMC Backup and Recovery utilizes
the VMware Changed Block Tracking (CBT) feature. CBT enables EMC Backup and
Recovery to only back up disk blocks that have changed since the last backup. This
greatly reduces the backup time of a given virtual machine image and provides the
ability to process a large number of virtual machines within a particular backup
window.
By leveraging CBT during restores, EMC Backup and Recovery offers fast and
efficient recoveries when you restore virtual machines to their original location. During

Deduplication store benefits 261

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

a restore process, EMC Backup and Recovery queries VADP to determine which
blocks have changed since the last backup, and then only recovers or replaces those
blocks during a recovery. This reduces data transfer within the EMC Backup and
Recovery environment during a recovery operation and reduces the recovery time.
Additionally, EMC Backup and Recovery automatically evaluates the workload
between both restore methods (full image restore or a recovery leveraging CBT) and
performs the method that results in the fastest restore time. This is useful in scenarios
where the change rate since the last backup in a virtual machine being restored is very
high and the overhead of a CBT analysis operation would be more costly than a direct
full-image recovery.
The advantages of image-level backups are:
l Provides full image backups of virtual machines, regardless of the guest operating
system
l Utilizes the efficient transport method SCSI hotadd when available and properly
licensed, which avoids copying the entire VMDK image over the network
l Provides file-level recovery from image-level backups
l Deduplicates within and across all .vmdk files protected by the EMC Backup and
Recovery appliance
l Uses CBT for faster backups and recoveries
l Eliminates the need to manage backup agents in each virtual machine
l Supports simultaneous backup and recovery for superior throughput

Connecting to the EMC Backup and Recovery user interface in the vSphere
Web Client
Perform the following to connect to the EMC Backup and Recovery user interface
within the vSphere Web Client.
Procedure
1. From a web browser, open the vSphere Web Client:
https://IP_address_vCenter_Server:9443/vsphere-client/

Note

If you receive an SSL certificate error in your web browser, refer to the
VMware knowledgebase article 1021514 at the following link:

http://kb.vmware.com/selfservice/microsites/search.do?
language=en_US&cmd=displayKC&externalId=1021514

2. In the Credentials window, type the vCenter user name and password for the
dedicated EMC Backup and Recovery user you created and then click Login.
3. In the vSphere Web Client, select EMC Backup and Recovery.
4. In the Welcome to EMC Backup and Recovery window, select an appliance
from the drop-down. This drop-down lists all the VMware Backup appliances
registered in the vCenter.
Each vCenter Server supports up to 10 appliances. The EBR Appliance field, as
shown in the following figure, displays the appliance names alphabetically in a
drop-down list. In the EMC Backup and Recovery user interface, the name of

262 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

the active appliance displays on the left pane, and the appliance name in the
drop-down list is the first in the list of available appliances.
Figure 133 Selecting the Backup Appliance

5. Click Connect.

Note

The maximum retry attempts for the VMware Backup appliance to connect to
the vCenter is two. Further attempts to connect to the vCenter requires
restarting the EMC Backup and Recovery server by typing the command

ebrserver.pl --restart.

Available tasks in the EMC Backup and Recovery user interface (VMware
Backup Appliance only)
The EMC Backup and Recovery user interface in the vSphere Web Client allows you
to configure and manage the VMware Backup Appliance.
When you connect to the vSphere Web Client and then click EMC Backup and
Recovery in the left pane, the following page displays.

Available tasks in the EMC Backup and Recovery user interface (VMware Backup Appliance only) 263
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 134 EMC Backup and Recovery user interface in the vSphere Web Client

The EMC Backup and Recovery user interface consists of five tabs:
l Getting Started—Provides an overview of functionality within the EMC Backup
and Recovery user interface along with quick links to assign virtual machines to a
workflow and to perform restores.
l Backup—Provides a list of scheduled backup workflows and details about each
workflow created in NMC. This window enables you to add the virtual machines/
VMDKs that you want protected to the workflows, and to run workflows on
demand.
l Restore—Provides a list of successful backups that you can restore.
l Reports—Provides backup status reports for the virtual machines on the vCenter
Server that you added to the workflow.
l Configuration—Displays EMC Backup and Recovery configuration information
and allows you to edit email settings. It also allows you to run integrity checks (for
example, checkpoint creation and validation).

Backup
The Backup tab displays information about available backup policies.

Table 23 Backup tab column descriptions

Column Description
Name The name of the backup policy.

State Whether the policy is enabled or disabled. Disabled backup policies will
not run. Also, a “No Schedule” state displays when you disable
Autostart in NMC for a policy.
Type The type of backup specified in the policy; for example, Image.

Last Start Time The last time the policy was started.

Duration The length of time the policy took to complete the last time it ran.

Next Run Time The next time the policy is scheduled to run.

264 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 23 Backup tab column descriptions (continued)

Column Description
Success Count The number of virtual machines that were backed up successfully the
last time the policy ran. This number updates after each backup.
Changes to a policy between backups will not be reflected in this
number until after the policy runs again. For example, if a backup
reports that 10 virtual machines successfully backed up, and then you
edit the policy so that only one virtual machine remains, this number
remains at 10 until the policy runs again and, if successful, the number
changes to one.

Failure Count The number of virtual machines that did not back up successfully the
last time the policy ran. This number updates after each backup.
Changes to a policy between backups will not be reflected in this
number until after the policy runs again. For example, if a backup
reports that 10 virtual machines failed to back up, and then you edit the
policy so that only one virtual machine remains, this number remains at
10 until the policy runs again and, if the backup fails, the number
changes to one.

Destination The location specified in the policy for the backup.

The following figure displays three example backup policies.

Figure 135 VMware Backup Appliance Backup tab

Available tasks in the EMC Backup and Recovery user interface (VMware Backup Appliance only) 265
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Restore
The Restore tab displays a list of virtual machines that were backed up using the
VMware Backup Appliance. By navigating through the list of backups, you can select
and restore specific backups.
Figure 136 VMware Backup Appliance Restore tab

Over time, the information displayed on the Restore tab may become out of date. To
view the most up-to-date information on backups available for restore, click Refresh.
More information on restore is provided in the section Restoring the VMware
environment on page 276.

Reports
On the Reports tab, you can view lists of task failures, job details, and unprotected
clients. You can also export report information to a CSV file by selecting Actions >
Export to CSV.
The following figure shows the Reports tab with the Job Details report selected.
Figure 137 VMware Backup appliance Reports tab

266 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Task Failures
The Task Failures tab lets you list all of the tasks that have failed, or filter the failed
tasks by Error, Job, or Client. When filtering task failures, select the options that
display depending on the type of failure you select.
You can rerun a failed task by selecting the task, and clicking Actions > Rerun Task.
The information displayed on the Task Failure tab is described in the following table.

Table 24 Task Failure column descriptions

Column Description
Failure Time The date and time that the task failed.

Reason The reason the task failed.

Client/Source The name of the client for which the task failed.
Name

Job Name The name of the job that failed.

Job Type The type of job that failed.

Next Run Time The next time the job is scheduled to run.

Job Details
The Job Details tab lets you display information about backup and restore jobs that
have occurred and that are scheduled. You can view information about all backup or
restore jobs, or filter the jobs by Client, Last Execution, and Next Execution. When
filtering jobs, select the options that display depending on the type of job you select.
The information displayed on the Job Details tab is described in the following table.

Table 25 Job Details column descriptions

Column Description

Client Information
Client Name The name of the client on which the job ran.

Type The type of job: Image, MS SQL, MS Exchange, MS SharePoint

Jobs The name of the job.

Last Execution
Job Name The name of the job that ran.

Completion The date and time the job completed. If the job has not run, this column
contains Never.

Result The result of the job: Success or Failure.

Next Execution
Job Name The name of the job that is scheduled to run.

Scheduled The date and time the job is scheduled to run again.

Available tasks in the EMC Backup and Recovery user interface (VMware Backup Appliance only) 267
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Unprotected Clients
The Unprotected Clients tab lets you display information about the clients the are
currently unprotected by the VMware Backup Appliance. You can list all unprotected
clients, or you can filter by Name, IP Address, or VM Path. When filtering clients,
select the options that display, and type the filter criteria in the text box.
The information displayed on the Unprotected Clients tab is described in the
following table.

Table 26 Unprotected Clients column descriptions

Column Description
Client Name The name of the client on which the job ran.

IP Address The client's IP address.

VM Path The client's VM path.

Configuration
The Configuration tab allows you to manage the maintenance tasks for the VMware
Backup Appliance.
Figure 138 VMware Backup Appliance Configuration tab

Viewing VMware Backup Appliance details

The Backup Appliance view on the Configuration tab shows you how the VMware
Backup Appliance is configured.
The details that are displayed are described in the following table.

Table 27 Backup appliance detail descriptions

Detail Description
Display name The name of the VMware Backup Appliance in the vCenter.

268 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 27 Backup appliance detail descriptions (continued)

Detail Description
Product name The name of the product.

IP Address The IP address of the VMware Backup Appliance.

Major Version The main version number of the VMware Backup Appliance.

Minor Version The build version of the VMware Backup Appliance.

Status The status of the VMware Backup Appliance.

Host The hostname of the VMware Backup Appliance.

vCenter server The IP address of the vCenter managing the VMware Backup Appliance.

NetWorker The IP address of the NetWorker server on which the VMware Backup
server Appliance is managed.

EBR backup user The user name used to log in to the vSphere Web Client.

EBR appliance The current time in the time zone set on the VMware Backup Appliance.
time

Time zone The time zone in which the VMware Backup Appliance is running.

You can configure these options during the VMware Backup Appliance installation. You
can also edit these options by using the EMC Backup and Recovery Configuration
utility as described in Post-installation configuration on page 240.

Viewing and exporting logs

The Log view on the Configuration tab displays a log that lists the activities that have
been initiated with the user interface and that identifies some key status items. You
can export the log information as a .log file if needed.
Procedure
1. On the Configuration tab, click Log.
A high-level log is displayed.

Available tasks in the EMC Backup and Recovery user interface (VMware Backup Appliance only) 269
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 139 Log view

2. Scroll through the log information, using the scroll bar and the Show next 2000
lines and Show all navigation buttons as needed.
3. Click Export View if you want to save the details that are displayed on the
screen to a file on the machine where your browser is running.
The Save As dialog box opens, and you can select where to save the file.

Configuring email
The Email view on the Configuration tab lets you configure EMC Backup and
Recovery to send SMTP email reports to specified recipients.
Procedure
1. On the Configuration tab, click Email.
The Email configuration screen displays.

270 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 140 Email configuration view

2. Click Edit.
3. Select the Enable email reports checkbox.
The configuration fields are enabled so that you can enter information.
4. Supply information in the fields using the definitions shown in the following
table.
Red asterisks indicate required information.

Table 28 Email configuration field descriptions

Field name Description

Outgoing mail Enter the name of the SMTP server that want to use to send email. This
server name can be entered as an IP address, a host name, or a fully qualified
domain name. The EMC Backup and Recovery appliance needs to be
able to resolve the name entered. The default port for non-
authenticated email servers is 25. The default port of authenticated mail
servers is 587. You can specify a different port by appending a port
number to the server name. For example, to specify the use of port
8025 on server "emailserver" enter: emailserver:8025

My server requires Check this box if your SMTP server requires authentication.
me to log in

Username Enter the username you want to authenticate with.

Password Enter the password associated with the username. (EMC Backup and
Recovery does not validate the password in any way; the password
entered is passed directly to the email server.)

From address Enter the email address you would like the email report to be from. This
can only be a single address.

To address(es) Enter a comma separated list of up to 10 email addresses.

Available tasks in the EMC Backup and Recovery user interface (VMware Backup Appliance only) 271
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 28 Email configuration field descriptions (continued)

Field name Description

Send time From the drop-down list choose the time you want EMC Backup and
Recovery to email reports.

Send day(s) Check the days you want the reports sent.

Report Locale From the drop-down list choose the locale for the email reports.

Enable CSV Select this option to enable the email to attach a CSV file.
Attachment

5. To test the email configuration, click Send test email.

Results
EMC Backup and Recovery reports sent by email will contain information similar to
that shown below.

Example-6.2.30.40 - (10.5.123.45)
--------------------------------------------------------------------
-
Report Date: February 27, 2012 - 15:12
Last Report Date: February 27, 2012 - 14:45

Appliance Status: Normal

Byte Capacity: 498.945 GiB
Bytes Free: 498.196 GiB
Used Capacity: 0.50%
Bytes Protected: 8 GiB
Bytes Deduped: 0.748 GiB
Integrity Check Status: Normal
Recent Successful Backups: 1
Recent Failed Backups: 1

Backup Jobs Summary

--------------------------------------------------------------------
Backup Job: another-one-with-vm-315
Backup Sources: VM-315
Last Start Time: February 27, 2012 - 15:07
Next Run Time: February 27, 2012 - 20:00
Last Successful Backups: 0
Last Failed Backups: 1
Backup Job: VM-315
Backup Sources: VM-315
Last Start Time: February 27, 2012 - 15:01
Next Run Time: February 27, 2012 - 20:00
Last Successful Backups: 1
Last Failed Backups: 0

Virtual Machines Summary

------------------------------------------------------------------
Virtual Machine: @#_+-&<>.
State: poweredOff
Backup Jobs:
Last Backup Job:
Last Successful Backup: Never
Last Backup Job Date: Never

Virtual Machine: VM-315

State: poweredOff
Backup Jobs: VM-315, another-one-with-
vm-315
Last Backup Job: another-one-with-vm-315

272 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Last Successful Backup: February 27, 2012 - 15:03

Last Backup Job Date: February 27, 2012 - 15:09

Running an integrity check

When EMC Backup and Recovery performs an integrity check, the appliance evaluates
whether the contents are internally consistent. You can run an integrity check from
any view on the Configuration tab.
Procedure
1. Select the EMC Backup and Recovery appliance's Configuration tab.
2. Click the gear icon, and select Run integrity check.
The following figure shows how to run an integrity check.
Figure 141 Run Integrity Check option

3. In the Confirm dialog box, click Yes.

A message displays that inform you that the integrity check was successfully
initiated.
4. Click OK.

Assigning virtual machines/VMDKs to a backup

Note

Even though you can use the EMC Backup and Recovery user interface in the
vSphere Web Client to assign virtual machines or VMDKs to a workflow that you
created in NMC, EMC recommends that you use NMC for this functionality.

You can assign collections of virtual machines (such as all virtual machines in a
datacenter), individual virtual machines, and VMDKs to be included in a policy's
workflow that you created in NMC using the EMC Backup and Recovery user
interface in the vSphere Web Client. If you select an entire resource pool, host,
datacenter, or folder, then subsequent backups will include any new virtual machines
in the container. If you select a virtual machine, then NetWorker includes any disk
added to the virtual machine in the backup. If you move the virtual machine from the
selected container to another unselected container, then the virtual machine is no
longer part of the backup.
You can also manually select a virtual machine for back up, which ensures that
NetWorker will back up the virtual machine, even when you move the virtual machine.
EMC Backup and Recovery will not back up the following specialized virtual machines:
l VMware Backup Appliances
l VMware Data Protection (VDP) Appliances
l Templates
l Secondary fault tolerant nodes
l Proxies

Assigning virtual machines/VMDKs to a backup 273

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l Avamar Virtual Edition (AVE) Servers

The wizard allows you to select these virtual machines; however, when you click
Finish, the wizard displays a warning that the job does not contain these special
virtual machines.
Procedure
1. Select EMC Backup and Recovery in the vSphere Web Client.
2. On the Getting Started tab, select Assign Backup Policy.
The Backup tab displays, which shows the available policy workflows in the
upper half of the window, and the workflow details in the lower half.

The description matches the description of the policy workflow in NMC.

3. Select the workflow to which you want to add a virtual machine or VMDK, and
then click Edit.
The Editing backup policy wizard opens, and displays all of the virtual
machines in the vCenter.
4. Click the checkboxes to select the virtual machines that you want to include in
the selected workflow, as shown in the following figure, or expand the virtual
machines to select VMDKs. You can also select other inventory objects, for
example, Resource Pools or Clusters in addition to specific virtual machines.

Note

You can only assign virtual machines and VMDKs to the workflows that you
create in NMC.

The following figure provides an example of how to select virtual machines in

the wizard.
Figure 142 Selecting virtual machines in the Editing backup policy wizard

5. Click Finish.
A message indicates that the policy workflow was saved successfully.
6. Click the Refresh button to refresh your screen.
You may have to click Refresh more than once. When the editing process has
completed, the Backup and Edit buttons become active again.

274 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Results
To see which backup sources are protected by a policy workflow, click Show items
next to Sources in the Backup policy details panel.

Manually starting a workflow by using Backup Now

Within the EMC Backup and Recovery user interface in the vSphere Web Client,
you can manually start the policy workflow that you created in NetWorker by using
the Backup tab.
Procedure
1. On the Backup tab, select the policy that you want to run.
2. Click Backup now, and select one of the following options:
l Backup all sources
l Backup only out of date sources
When you start the workflow, any clone actions associated with the workflow
will also run.

Note

If you disabled the Backup Now functionality in the NSR VBA Server
Properties window in NetWorker, as described in the section VMware Backup
Appliance monitoring and properties on page 251, a message displays when you
click this button indicating that Backup Now is locked and not available.

Otherwise, you can wait for NetWorker to start the workflow based on the
scheduled start time.

Stopping a workflow
Procedure
1. Select the Backup tab.
2. in the Recent Tasks pane, click the circular x symbol associated with the
workflow.

Viewing workflow progress

To view the progress for a policy's workflow, select Tasks in the left pane of the
vSphere Web Client.
The Task Console displays, as shown in the following figure.

Manually starting a workflow by using Backup Now 275

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 143 Viewing workflow progress in the Task Console

After the backup completes, you can recover the virtual machine in the vSphere Web
Client or use the EMC Data Protection Restore Client to perform a file-level
restore.

Restoring the VMware environment

The NetWorker VMware Protection solution provides two levels of restore
functionality:
l A FULLVM (image-level) restore will restore an entire backup image or selected
drives to the original VM, another existing VM, or a new VM. These restores are
less resource intensive and are best used for restoring large amounts of data
quickly.
l File-level restores will restore specific folders or files from an image backup. These
restores are more resource intensive and are best used to restore a relatively small
amounts of data.

FULLVM (Image-level) Restore

When the backup completes, you can perform an image-level restore of full virtual
machines by selecting either of the following options in the EMC Backup and
Recovery user interface:
l Click Restore Backup on the Getting Started tab.
l Select the Restore tab.
When you select the Restore tab, available virtual machines for the selected appliance
display. Additionally, you can select a different appliance from the Restore points
from drop-down, as described in the section Recovering from a secondary site. For
every clone, a backup appears under the restore point.

276 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 144 Restore tab in EMC Backup and Recovery user interface

Image-level restore with resurrection

Restores from devices will be slow if resurrection is required. Resurrection is a type of
recovery in which the primary backup (or snapup) in the VMware Backup Appliance is
no longer available. Resurrection is not supported for VMDK-level backups, and you
can only perform resurrection when you associate a client with the policy.
For Data Domain devices, resurrection only occurs when restoring a cloned backup.
For AFTD and tape devices, resurrection requires a local Data Domain device on the
NetWorker server. For a Cloud Boost device, a resurrection restore can take more
than an hour depending on the virtual machine size, during which time the only
progress that displays is message within ebrserver.log showing a save set copy is in
progress.

Note

If there is no staging pool available when resurrecting from an AFTD, the restore does
not fail automatically after timing out. You must manually cancel the restore operation.

Performing a FULLVM restore

Procedure
1. If restoring the VM to its original location, power off each virtual machine that
you want to restore.

Note

Power off is not required if restoring the VM to a new location.

2. In EMC Backup and Recovery, on the Restore tab, use the Restore points
from drop-down to select the appliance from which you want to restore.
EMC Backup and Recovery displays the virtual machines that are available to
restore.
3. Click the virtual machine that you want to restore to expand its backups.
Use the Filter drop-down to display a specific VM and related items. You can
also click a backup to display the VMDK level and select a single VMDK for
restore, if you only want to restore that disk.
4. Select a backup, and then click Restore.
The Restore Backup wizard launches.
5. On the Select Backup page, verify that the list of backups is correct. Remove
any backup that you want to exclude, and click Next.
6. On theSet Restore Options page, perform one of the following tasks:

FULLVM (Image-level) Restore 277

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l Select the Restore to original location option to restore the backup to its
original location. If the VMDK file still exists at the original location, the
restore process overwrites the file.
l Unselect the Restore to original location option, and specify a new name
and destination where the virtual machine or VMDK will be restored.
7. Optionally, select Advanced options to set the VM to Power On and
Reconnect NIC after the restore process completes.

Note

Reconnect NIC is enabled by default and greyed out. Only when you select
Power On are you given the option to clear the Reconnect NIC option.

8. Click Next.
9. On the Ready to complete page, verify the selections. The wizard displays a
summary of the number of machines that will be replaced (restore to the
original location) and the number of machines that will be created (restore to a
new location).
10. To change any of the settings for your restore request, either use the Back
button to return to the appropriate screen, or click the appropriate numbered
step title to the left of the wizard. If the settings are correct, then click Finish.
The Restore Backup wizard displays a message that the restore process
initiated successfully.
11. Click OK.
You can monitor the restore progress by using the Recent Tasks pane.

Note

If you selected Reconnect NIC during the restore process, then confirm the
network configuration for the newly-created virtual machine. Once the restore
completes, the new virtual machine NIC might use the same IP address as the
original virtual machine, which will cause conflicts.

Results
When the recovery starts, a recovery session also displays in NMC. Any activities that
occur on the vCenter side are visible on the NMC side.

Canceling a FULLVM restore

To cancel a restore at any time during setup, click the circular x symbol associated
with the restore job in the Recent Tasks pane.

Instant Access restore (for Data Domain systems only)

If your primary backup is located on a Data Domain system, clicking the Instant
Access button on the Restore tab allows you to perform a quick restore of these
backups, the same as you would perform a typical FULLVM restore. No further
configuration is required to use this feature.
The Instant Access restore operation has the following limitations:
l The free space on the Data Domain system must be equal to or greater than the
total disk size of the VM being restored, as the restore does not take into account
the actual space required after deduplication occurs. If there is insufficient disk

278 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

space, an error appears indicating "Insufficient disk space on datastore," and

creation of the target VM fails.
l You cannot use the Instant Access button when you select more than one
different Data Domain system backup for multiple VMs.
l You can perform only one Instant Access restore at a time. Ensure that you
vMotion the VM to a different datastore and that you unmount the datastore
before performing another instant access restore for the Data Domain system.
l You cannot recover multiple save sets concurrently using Instant Access restore.
Procedure
1. In the EMC Backup and Recovery user interface, select the Restore tab.
EMC Backup and Recovery displays the virtual machines that are available to
restore.
2. Click a virtual machine to expand the list of available backups, from which to
restore.

Note

You cannot browse and select backup data at the disk level.

3. Select the backup that you want to restore, and click Instant Access.
The Instant Access wizard opens to the Select Backup page.
Figure 145 Select a backup

4. Verify that the list of backups is correct, remove any backups that you want to
exclude from the restore, and click Next.
The Set Instant Access Options page displays.

FULLVM (Image-level) Restore 279

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 146 Set instant access options

5. Specify a new name and destination for the restore, and click Next.
The Ready to complete page displays.
Figure 147 Ready to complete

6. Review the restore request, and click Finish.

You should see a message that indicates that the instant access operation was
successfully completed.

Restore from last backup

The vSphere Web Client also provides an option to perform a VMware Backup
Appliance restore from the last successful backup. This option is available when you
right-click the VM and select All EBR actions > Restore from last backup.

Note

Before you use this option, make sure that you establish a connection to the VMware
Backup Appliance by selecting the EMC Backup and Recovery user interface in the
vSphere Web Client.

280 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Direct to host recovery

You can recover image-level backups directly to an ESX host without requiring a
vCenter server by using the Emergency Restore tab EMC Backup and Recovery
Configure window. Direct to host recovery is available only for VMs that you back up
to a VMware Backup appliance.
Before performing an emergency restore, ensure that you meet the following
requirements:
l The VM you want to restore must have a VMware Hardware version that is
supported by the ESX host running the VMware Backup Appliance (VMware
Hardware version 7 or later).
l A vSphere host that is currently managed by the vCenter Server must be
temporarily disassociated from the vCenter Server to perform the emergency
restore. To disassociate the vCenter Server, use the vSphere Client (not the
vSphere Web Client) connected directly to the vSphere host.
l You must have adequate free space in the target datastore to accommodate the
entire VM. The target VMFS datastore to which the VM is being restored must
support the VMDK file size.
l Network connectivity must be available for the restored VMs from the ESX host
running the VMware Backup Appliance.
l You must have at least one local account with administrator privileges on the ESX
host running the VMware Backup Appliance.

Note

You can only perform an emergency restore from a primary backup; you cannot use a
cloned backup.

Procedure
1. Log in to the EMC Backup and Recovery Configure window at the following
URL using the EMC Backup and Recovery username and password credentials
that you defined during configuration:
http://VMware_Backup_appliance_IP:8580/ebr-configure

2. Select the Emergency Restore tab.

3. Click Refresh to view the most recent available VM backups.
4. Click the arrow beside a restore point to display its backups.
5. Select the backup that you want to restore, and then click Restore.
The following figure provides an example of the Emergency Restore window.

FULLVM (Image-level) Restore 281

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 148 Emergency Restore window

File-level restore
Where FULLVM restore allows you to restore backups in their entirety using the EMC
Backup and Recovery user interface in the vSphere Web Client, file-level restore
(FLR) allows you to restore specific files and folders from virtual machines by using
the EMC Data Protection Restore Client, or from a command prompt by using the
nsrvbaflr command, which is part of the base NetWorker client install.
The following text is an example of how to use the nsrvbaflr command:
nsrvbaflr --vba 10.7.77.200 --adminuser [email protected] --
adminpass pw123 --sourceclient /10.7.84.219/VirtualMachines/jinTest4
--targetclient /10.7.77.227/VirtualMachines/lava12204-win --targetpath
C: --targetuser Administrator --targetpass pw456 --recover [Disk#1]

Note

If you plan to use the nsrvbaflr command, you must copy the nsrvbaflr java
script (nsrvbaflr.exe on Windows) to the virtual machine you want to restore from.
The NetWorker Command Reference Guide provides information about how to use the
nsrvbaflr command.

The EMC Data Protection Restore Client, which you access through a web browser,
allows you to select specific virtual machine backups as file systems, and then browse
the file system to locate the directories and files you want to restore.
The Restore Client operates in one of two modes:
l User—A local user account with administrative privileges that can restore folders
or files to the original virtual. The section Restoring specific folders or files to the
original virtual machine (User mode) provides more information.
l Admin—A vCenter administrator account that can restore folders or files from a
different VM to any available destination client. The section Restoring specific
folders or files from a different virtual machine (Admin mode) provides more
information.

282 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Note

Before you start a file-level restore, review the limitations specified in the section FLR
limitations to ensure that you can perform FLR in your configuration.

File-level restore limitations

This section provides a list of limitations that apply to file-level restore.

Note

Before performing a file-level restore, make sure that your browser is updated to the
latest version.

l In a large environment where many virtual machines appear in the EMC Data
Protection Restore Client, the navigation buttons (Back, Next, Finish) may
appear very small, requiring you to zoom in to see the options. If this occurs, it is
recommended that you use the latest versions of the Chrome or Firefox browsers
to avoid the issue.
l You can only restore files and/or folders from a Windows backup to a Windows
machine, or from a Linux backup to a Linux machine.
l You must install VMware Tools to use file-level restore. For best results, ensure
that all virtual machines run the latest available version of VMware Tools. Older
versions are known to cause failures when you perform browse actions during the
file-level restore operation.
l You can perform file-level restore across vCenter servers as long as the vCenter
servers are configured in the same NetWorker server, and the source and target
virtual machine have the same guest operating system. For example, Linux to
Linux, or Windows to Windows.
l File-level restore does not support the following virtual disk configurations:
n Dynamic disks
n Unformatted disks
n FAT16 file systems
n FAT32 file systems
n Extended partitions (Types: 05h, 0Fh, 85h, C5h, D5h)
n Two or more virtual disks mapped to single partition
n Encrypted partitions
n Compressed partitions
n Btrfs
n XFS
l File-level restore does not restore or browse symbolic links.
l When you create partitions, fill the lower ordered indices first. For example, you
cannot create a single partition and place it in the partition index 2, 3, or 4. You
must place the single partition in partition index 1.
l File-level restore of Windows 8 and Windows Server 2012 virtual machines is not
supported on the following file systems:
n Windows Dynamic Disks

File-level restore 283

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

n Deduplicated NTFS
n Resilient File System (ReFS)
n EFI bootloader
l File-level restore of ext4 file systems is supported only with external proxies. To
perform FLR of ext4 file systems, you must disable the internal proxies from the
NSR VBA Server Properties window in NMC. VMware Backup Appliance
monitoring and properties on page 251 provides more information.
l File-level restore does not support a direct restore from a cloned backup. To
recover individual files from a clone, you must first perform an image-level
recovery of the clone. This creates a primary copy on the VMware Backup
appliance, from which you can then perform file-level restore.
l File-level restore does not restore ACLs.
l File-level restore cannot restore more than 5,000 folders or files in the same
restore operation.
l File-level restore cannot browse more than 14,498 folders or files in the same
restore operation.

Restoring specific folders or files to the original virtual machine in User mode
Select the User tab in the EMC Data Protection Restore Client login page to restore
specific folders and files to the original virtual machine on Windows and Linux virtual
machines. In this mode, you connect to the Restore Client from a virtual machine that
has been backed up by NetWorker VMware Protection.
Procedure
1. Connect to the host that will receive the file-level restore with a user that is a
member of the administrations group.
2. Open a browser and enter a URL that points to the VMware Backup Appliance
and indicates file-level restore. For example:

http://VMware_Backup_Appliance_host:8580/flr

The following figure provides an example of the user login window.

Figure 149 EMC Data Protection Restore Client User Login

284 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Note

You must connect to the VMware Backup Appliance from a web browser on the
virtual machine that the files will be restored to.

3. Select the User tab, and then log in to the Restore Client with the local
administrative credentials of the virtual machine to which you are logged in.
When you log in, the Select the backup(s) to restore from page displays with
a list of backups for the local virtual machine.
4. Use the drop-down list to view the available backups. You can view all backups,
or only backups on a specific date or within a specific range. Highlight a backup
and double-click or drag and drop to move the backup to the Select Items
pane. Click Next.
The following figure provides an example of the Select the backups to restore
from page.
Figure 150 Select the backups to restore from page

Note

When you click Next, if a folder hierarchy does not appear, the file system in
use on the virtual machine may not support file-level restore. The section File-
level restore limitations on page 283 provides more information.

5. On the Select items to restore page, browse and select the files and folders
available for recovery. You can sort items by Name, Date, and so on. Items
marked for restore appear in the Selected Items pane. To mark an item for
recovery, double-click the item, or drag and drop the item into the Selected
Items pane.

File-level restore 285

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 151 Select items to restore page

6. On the Select destination to restore to page, select the folder to which you
want to restore the items, and then click Finish.
The following figure provides an example of the Select destination to restore
to page.
Figure 152 Select destination to restore to page

7. Click Yes when you are prompted to continue the restore.

The restore begins.
8. To monitor the progress of the restore operation, click the arrow button located
at the lower right-hand corner of the restore client screen.

286 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

The following figure provides an example of the arrow button.

Figure 153 Accessing the restore monitor

When you select the arrow button, the Restore Monitor panel slides up. The
following figure provides an example of the Restore Monitor panel.
Figure 154 Restore Monitor panel

Click the Refresh button on the right-hand side of the panel to refresh the
contents as the restore occurs.

Restoring specific folders or files from a different virtual machine in Admin mode
To restore specific folders or files from a different virtual machine, use Admin mode in
the EMC Data Protection Restore Client login page. Once connected, you can
browse, select, and restore files and folders from any virtual machine that you backed
up by using NetWorker VMware Protection. You can then restore items to the virtual
machine on which you are currently logged in, or to any available destination virtual
machine.
Procedure
1. Open a browser and specify the URL that points to the EMC Backup and
Recovery appliance and indicates file-level restore (FLR), as in the following
example:
http://VMware_Backup_Appliance_host:8580/flr

Ensure that you launch the EMC Data Protection Restore Client from a virtual
machine that you backed up using the NetWorker VMware Protection solution.
2. Click Admin, and then log in to the Restore Client with the vCenter
administrative credentials that you used to register the VMware Backup
appliance to the vCenter Server.
The following figure provides an example of the Admin login window.

File-level restore 287

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 155 EMC Data Protection Restore Client Admin Login

Note

When you use Admin mode, ensure that the user you specify for the vCenter
login has the correct privileges to use this option.

When you log in, the Select the backup(s) to restore from page appears with
a list of all the virtual machines that were backed up by using NetWorker
VMware Protection. The available backups appear under each virtual machine.
3. Use the drop-down list to view the available backups. You can view all backups,
or only backups on a specific date or within a specific range. Highlight a backup
and double-click or drag and drop to move the backup to the Select Items
pane. Click Next.
4. On the Select items to restore page, browse and select the files and folders
available for restore. You can sort items by Name, Date, and so on. Items
marked for restore appear in the Selected Items pane. To mark an item for
recovery, double-click the item, or drag and drop the item into the Selected
Items pane.
5. In the Select Restore Client page, select a destination virtual machine.
A login dialog box similar to the following figure appears for the destination
client.

Figure 156 Select and log in to the destination client

6. Log in to the client.

7. Select the destination location where you want to restore the file.
8. Click Finish.
9. Click Yes when you are prompted to continue with the restore.
The restore begins.

288 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

10. To monitor the progress of the restore operation, click the arrow button located
at the lower right-hand corner of the restore client screen.
The following figure provides an example of the arrow button.
Figure 157 Accessing the restore monitor

When you select the arrow button, the Restore Monitor panel slides up. The
following figure provides an example of the Restore Monitor panel.
Figure 158 Restore Monitor panel

Click the Refresh button on the right-hand side of the panel to refresh the
contents as the restore occurs.

Monitoring EMC Backup and Recovery activity

You can monitor backup and recovery activities from the EMC Backup and Recovery
user interface in the vSphere Web Client, with the EMC Data Protection Restore
Client and from the command line.
Most EMC Backup and Recovery tasks, events, and alarms are prefaced by “EBR:”
Note that some of the tasks and events that occur as part of EMC Backup and
Recovery processes are performed by the vCenter Server and do not have this prefix.
For example, if EMC Backup and Recovery runs a scheduled backup job for a running
virtual machine, the following task entries are created:
l Create a VM snapshot (vCenter acting on the VM to be backed up).
l EMC Backup and Recovery: Scheduled Backup Job (EMC Backup and Recovery
starting the backup job).
l Reconfigure the VM (the VMware Backup appliance requesting services from
vCenter).
l Remove snapshot (vCenter acting on the VM that has completed backing up).
To see only EMC Backup and Recovery-generated tasks or events in the Tasks or
Event console, click Event in the left pane, and type EMC Backup and Recovery: in
the Filter field.

Monitoring EMC Backup and Recovery activity 289

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Viewing Recent Tasks in the vSphere Web Client

The EMC Backup and Recovery user interface in the vSphere Web Client displays task
entries in the Recent Tasks window when you perform the following operations:
l Backups
l Restores
l Integrity Checks
Click on a task entry in the Recent Tasks window to display task details in the pane at
the bottom of the window. You can also display task details by clicking the link next to
the VM icon on the Running tab in the Recent Tasks section.
To cancel tasks from the Running tasks pane, click the Delete icon.

Viewing Alarms
EMC Backup and Recovery can trigger the following alarms:

Table 29 EMC Backup and Recovery alarms

Alarm Name Alarm Description

EBR: [001] The most recent checkpoint for From the Configuration tab of the EMC
the VMware Backup appliance is outdated. Backup and Recovery user interface, click the
All Actions icon, and then select Run
integrity check.
EBR: [002] The VMware Backup appliance is The VMware Backup Appliance is nearly out
nearly full. of disk space for additional backups. You can
free disk space on the appliance by manually
deleting unnecessary or older backups and by
changing retention policies on backup jobs, to
shorten the backup retention time.

EBR: [003] The VMware Backup appliance is The VMware Backup Appliance does not have
full. any disk space for additional backups. The
appliance will run in read-only (or restore-
only) mode until you make additional space
available. You can free space on the appliance
by manually deleting unnecessary or older
backups and by changing retention policies on
backup jobs to shorten the backup retention
time.

EBR: [004] The VMware Backup appliance The datastore that contains the disks
datastore is approaching maximum capacity. provisioned for the VMware Backup Appliance
is approaching maximum capacity. When
datastore reaches the maximum capacity, the
VMware Backup Appliance will be suspended.
The appliance cannot be resumed until
additional space is made available on the
datastore.

EBR: [005] Core services are not running. The Core services are not running. Start the
Core services by using the EMC Backup and
Recovery Configure window.

290 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 29 EMC Backup and Recovery alarms (continued)

Alarm Name Alarm Description

EBR: [006] Management services are not The Management services are not running.
running. Start Management services by using the EMC
Backup and Recovery Configure window.

EBR: [007] File system services are not The File system services are not started. Start
running. the File system services by using the EMC
Backup and Recovery Configure window.
Note

This alarm does not apply to EBR version

1.5.1.7.

EBR: [008] File level restore services are not The File level restore services are not started.
running. Start the File level restore services by using
the EMC Backup and Recovery Configure
Note window.
This alarm does not apply to EBR version
1.5.1.7.

EBR: [009] Maintenance services are not The Maintenance services are not running.
running. Start Maintenance services by using the EMC
Backup and Recovery Configure window.

EBR: [010] Backup scheduler is not running. The Backup scheduler is not running. Start
Backup scheduler by using the EMC Backup
and Recovery Configure window.

Viewing the Event Console

EMC Backup and Recovery can generate info, error, and warning events. For example:
l Info— “EMC Backup and Recovery: Critical VMs Backup Job created.”
l Warning— “EMC Backup and Recovery: Unable to add Host123 client to backup
job Critical VMs because . . .”
l Error— “EMC Backup and Recovery: Appliance has changed from Full Access to
Read Only.”
EMC Backup and Recovery generates events on all state changes in the appliance. As
a general rule, state changes that degrade the capabilities of the appliance are labeled
errors, and state changes that improve the capabilities are labeled informational. For
example, when starting an integrity check, EMC Backup and Recovery generates an
event that is labeled an error because the appliance is set to read-only before
performing the integrity check. After the integrity check, EMC Backup and Recovery
generates an informational event because the appliance changes from read-only to full
access.
Select an event entry to display the details of that event, which includes a link to
Show related events.

Viewing the Event Console 291

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Shutdown and Startup Procedures

If you need to shut down the VMware Backup Appliance, use the Shut Down Guest OS
action. This action automatically performs a clean shutdown of the appliance. If you
power off the appliance without using the Shut Down Guest OS action, corruption
might occur. It can take up to 30 minutes to shut down and restart the VMware
Backup Appliance. You can monitor the status through the EMC Backup and Recovery
Console in the vSphere Client. After vSphere shuts down the appliance, use the
Power On action to restart the appliance.
If the appliance does not shutdown properly, then a rollback to the last validated
checkpoint action occurs during the restart. This means that any changes to backup
policies or backups that occur between the checkpoint and the unexpected shutdown
will be lost. This is expected behavior and is used to ensure system corruption does
not occur from unexpected shutdowns.
The VMware Backup Appliance is designed to run 24x7, to support maintenance
operations and to provide the ability to perform restore operations. EMC does not
recommend that you shutdown the appliance, unless there is a specific reason for the
shutdown.

EMC Backup and Recovery Capacity Management

This section focuses on EMC Backup and Recovery capacity management and
includes the following topics:
l Impact of selecting thin or thick provisioned disks on page 292
l Save set lifecycle on page 293

Impact of selecting thin or thick provisioned disks

This section describes the advantages and disadvantages of selecting a thin or thick
disk partitioning for the EMC Backup and Recovery datastore.
Thin provisioning uses virtualization technology to allow the appearance of more disk
resources than what might be physically available. Use thin provisioning when an
administrator actively monitors disk space and can allocate additional physical disk
space as the thin disk grows. If you do not monitor and manage disk space and the
EMC Backup and Recovery datastore is on a thin provisioned disk that cannot allocate
space, the VMware Backup appliance fails. When this occurs, you can rollback to a
validated checkpoint. Any backups and configuration changes that occurred after the
checkpoint will be lost.
Thick provisioning allocates all of the required storage when the disk is created. The
best practice for the EMC Backup and Recovery datastore is to create a thin
provisioned disk when the EMC Backup and Recovery appliance is deployed (this
allows for rapid deployment), and then convert the disk from thin provisioning to thick
provisioning after deployment.

Note

See the VMware documentation for details on inflating thin provisioned disks to thick
provisioned disks. This procedure requires that you shut down the VMware Backup
appliance. This may take several hours to complete.

292 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Save set lifecycle

The NetWorker server exclusively manages the lifecycle of save sets created by
VMware Backup Appliance nodes.

Deletion and expiration of save sets and metadata

The following sections describe how to delete and expire save sets and metadata on
the NetWorker server.

Expiring save sets from NetWorker

NetWorker manages the retention period for the VMware Backup Appliance backups.
When a save set for the appliance expires in NetWorker, NetWorker deletes the
corresponding backup data from the storage on the appliance.

Manual deletion of save sets from NetWorker

Use the nsrmm command to delete EMC Backup and Recovery Appliance backups
from the media database on the NetWorker server.
For example:

nsrmm -d -S ssid/cloneid

where ssid/cloneid is the SSID and cloneID of the save set that you want to delete.
When you delete a save set from NetWorker server, NetWorker will also remove the
corresponding backup from the EMC Backup and Recovery Appliance.

Data Domain backup

If a Data Domain backup has multiple clones, then deleting the primary clone only
deletes the copy on the EMC Backup and Recovery appliance.
Deleting a Data Domain volume
You can delete a user-defined Data Domain device volume that contains VMware
Backup Appliance backups after you unmount the devices. If NetWorker cannot delete
the backups from the VMware Backup appliance, then the volume deletion operation
fails.
Relabeling a Data Domain volume
You can relabel a user-defined Data Domain volume that the VMware Backup
Appliance uses in the same method as any other volume. The relabel operation deletes
all the VMware Backup Appliance backups that belong to the volume associated with
the device from both NetWorker and the VMware Backup Appliance server. If
NetWorker cannot delete the backups from the VMware Backup Appliance, then the
device relabel operation fails.

Checkpoints and VMware Backup Appliance rollback

The maintenance services for EMC Backup and Recovery start between 24 to 48
hours after booting up, and maintenance services are responsible for creating
checkpoints. A checkpoint is initiated within the vSphere Web Client and captures a
point in time snapshot of the VMware Backup Appliance for disaster recovery
purposes. In the event that you need to recover the VMware Backup Appliance, a
rollback setting within the EMC Backup and Recovery Configure window allows the
VMware administrator to automatically roll back to the last validated checkpoint.

Save set lifecycle 293

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

By default, checkpoints are automatically scheduled during the maintenance window.

In addition to the twice daily checkpoints, you can also create and validate additional
EMC Backup and Recovery server checkpoints at any time.
Checkpoint validation might take several hours, depending on the amount of data in
the NetWorker server. You can configure each validation operation individually to
perform all checks (full validation) or perform a partial “rolling” check, which fully
validates all new and modified stripes, then partially checks a subset of unmodified
stripes. You can also delete checkpoints to reclaim server storage capacity.

Creating a checkpoint using the EMC Backup and Recovery user interface
You can create a validated checkpoint by using the command line or the EMC Backup
and Recovery user interface in the vSphere Web Client. The section Preparing the
VMware Backup appliance for disaster recovery on page 298 provides information on
creating and validating checkpoints from the command line.
Procedure
1. In the EMC Backup and Recovery user interface, select the Configuration tab.
2. Click the gear icon, and then select Run integrity Check as shown in the
following figure.
Figure 159 Running an integrity check

Rolling back to a checkpoint

Rollback is a setting in the EMC Backup and Recovery Configure window that allows
you to automatically roll back to the last validated checkpoint when performing a
disaster recovery.
Procedure
1. Log in to the appliance at http://VMware Backup appliance FQDN:8580/
ebr-configure.
2. Select the Rollback tab.
The following figure provides an example of the Rollback tab.

294 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 160 Roll back to checkpoint

Note

NetWorker does not support disaster recovery from a checkpoint backup that
was performed with a VMware Backup Appliance version earlier than the
currently installed version. For example, if you upgrade to a NetWorker 18.1
server and VMware Backup Appliance version 1.5.1.7 from NetWorker 8.2 SP1
and VMware Backup Appliance version 1.1.1.50, you cannot perform a disaster
recovery from a checkpoint backup created with OVA 1.1.1.50. Backup and
restore operations will hang in "Waiting: Queued" state.

3. Click Unlock to enable the rollback operation.

4. When prompted, type the appliance password, and then click OK.
5. Select a validated checkpoint, and then click Perform EBR rollback to
selected checkpoint.
6. On the EBR Rollback window, click OK.

Protecting checkpoints for the VMware Backup appliance

To protect the appliance with checkpoints, add the VBA checkpoint discover and VBA
checkpoint backup actions to a data protection policy.

You should run backups once or twice daily that occur a couple hours after checkpoint
creation, to secure the checkpoint files on the NetWorker media. Preparing the
VMware Backup appliance for disaster recovery on page 298 provides a list of
checkpoint locations.

Cross Sync
A cross sync operation synchronizes the VMware Backup Appliance and NetWorker
databases for backups and configurations. A VMware Backup Appliance rollback
automatically starts a cross sync operation on the NetWorker server. You can also
perform a cross sync manually from the command line to check the consistency of the

Protecting checkpoints for the VMware Backup appliance 295

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

NetWorker metadata. Before you perform a cross sync, ensure that the VMware
Backup Appliance is online.
Use the following command to manually perform cross sync from the command line of
the NetWorker server:
nsrim -X -S -h EMC_Backup_and_Recovery_appliance_hostname -t last
checkpoint time -f
where:
l -S initiates the VMware Backup appliance cross sync.
l -h specifies the VMware Backup appliance server name.
l -t is an optional parameter that specifies the last checkpoint time. EMC Backup
and Recovery performs a cross sync for the backups that occur only after the
specified time. Specify the time in a format that NetWorker accepts. The
nsr_getdate man page provides information on acceptable formats.
l -f synchronizes the entire database and deletes out of sync backups. If the
backups exist only on the VMware Backup appliance, then you can only delete the
backups by using this option.
To cross sync the entire database, specify -f without specifying the time.
If you do not specify a time when you perform a manual cross sync, NetWorker
retrieves the most recent validated checkpoint from the VMware Backup appliance
and performs a cross-sync starting from that time.
If you perform a cross sync on an entire database and the database is very large, the
synchronization process may take longer than normal.
Cross sync generates the following NMC events:
l “Cross sync with appliance name VMware Backup Appliance is
started.”
l “Cross sync with appliance name VMware Backups Appliance is
successful for configuration and backups.”

Disaster Recovery
In the event of failure, as a first course of action, NetWorker VMware Protection will
perform a rollback to a known validated checkpoint. To recover from a VMware
Backup Appliance failure, refer to the following disaster recovery guidelines.

Disaster Recovery Guidelines

Review these guidelines before performing a disaster recovery:
l When you set the save set retention policy, ensure that the save sets in the media
database are active and not expired and recycled.
l Ensure that the checkpoint backup that you plan to use was created with the same
VMware Backup Appliance version as the version currently installed. NetWorker
does not support disaster recovery from a checkpoint backup created using a
previously installed VMware Backup Appliance version. For example, if you
upgrade to a NetWorker 18.1 server and VMware Backup Appliance version 1.5.1.7
from NetWorker 8.2 and VMware Backup Appliance version 1.1.0.149, you cannot
perform a disaster recovery from a checkpoint backup created with OVA 1.1.0.149.
Backup and restore operations will hang in the "Waiting: Queued" state.

296 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l Although the 0.5TB appliance contains 3 * 256 GB disks and the 4TB appliance
contains 6 * 1TB disks, NetWorker only creates one checkpoint save set for all the
disks. Ensure that you know which VMware Backup Appliance (0.5 or 4TB) that
you deployed before you perform a disaster recovery. This information is not
required when performing the checkpoint backup, but you will require this
information during the re-deployment of the appliance. To help identify the
deployed appliance and verify the checkpoint backup, you can review the log
messages that appear in the daemon.raw file on the NetWorker server, and
within the policy logs. The location of the logs files differ on a Windows and Linux
NetWorker server.
n Linux—By default the daemon.raw file appears in the /nsr/logs directory.
The policy log files appear in the /nsr/logs/policy directory.
n Windows—By default the daemon.raw file appears in the C:\Program
Files\EMC NetWorker\nsr\logs folder. The policy log files appear in the
C:\Program Files\EMC NetWorker\nsr\logs\policy folder.
l Before you shut down the VMware Backup Appliance, verify that there are not any
backup or maintenance tasks running. Depending on the backup method used and
how long it takes, schedule your checkpoint backup during a time when no tasks
are scheduled. For example, if your backup window is eight hours and backups only
take one hour to complete, you have an additional seven hours before maintenance
tasks are scheduled. This is an ideal time to shut down and backup the appliance.
l To shutdown the appliance, use the vSphere Client to perform a Shut Down
Guest OS task on the virtual machine. Do not use a Power Off task, which is the
equivalent to unplugging the power cord on a physical server and may not result in
a clean shut down process. Shutdown and Startup Procedures on page 292
provides more information.

Disaster recovery without checkpoint

Use the following procedure to perform a disaster recovery of the VMware Backup
Appliance without using checkpoints.

Note

When you perform a disaster recovery for a VMware Backup Appliance without using
checkpoints, you can only perform a FULL VM (image-level) restore. VMDK, FLR, and
instant access restores are not supported in this case. You can, however, perform
these types of restore after a resurrection restore.

Procedure
1. Deploy a new VMware Backup Appliance and specify the same IP address that
was used at the time of the backup, from which you are recovering.
EMC Backup and Recovery Configuration Utility on page 235 provides
instructions.
2. Configure the new VMware Backup Appliance.
During the NetWorker Registration step, select the Override NetWorker
registration check and the Force cross sync with NetWorker after re-
deployment options.

The following figure provides an example of the NetWorker Registration page.

Disaster recovery without checkpoint 297

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 161 Networker registration during new appliance configuration

3. Click Next, and finish the configuration.

Results
Once the VMware Backup Appliance configuration completes, the following events
appear in NMC:
Cross sync with appliance name VMware Backup Appliance is
started.
Cross sync with appliance name VMware Backups Appliance is
successful for configuration and backups.

You can then perform a resurrection restore of previous backups.

Preparing the VMware Backup appliance for disaster recovery

Perform the following steps to prepare for a disaster recovery of the VMware Backup
appliance.

Note

When you use ssh to connect to or log in to the EMC Backup and Recovery console,
ensure that you log in with admin account instead of the root account. Log in to the
EMC Backup and Recovery Console as admin instead of root on page 312 provides
more information.

Procedure
1. If you do not have a recent checkpoint or want to create a new checkpoint
backup, create the checkpoint by running the following command:
# mccli checkpoint create --override_maintenance_scheduler

2. Use the mccli command to verify that you have created a successful
checkpoint by running:
mccli checkpoint show
An output similar to the following displays:
Tag Time Validated Deletable
----------------- ----------------------- ---------
---------
cp.20130206170045 2013-02-06 09:00:45 PST Validated Yes

298 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

3. Use the mccli command to validate the checkpoint:

mccli checkpoint validate --cptag=cp.20130206170045 --
override_maintenance_scheduler
Validation takes some time to complete. Keep checking the status by running
mccli checkpoint show.

4. Use the NetWorker Administration GUI to add two actions to a workflow for the
VMware Protection Policy, in the following order:
a. VMware checkpoint discover action.
b. VMware checkpoint backup action.

Note

Checkpoint backup is a traditional NetWorker backup that you can perform

to any NetWorker-supported pool. The pool can include Data Domain
devices and AFTDs.

Optionally, add a clone action after the checkpoint backup action to clone
the checkpoint backup to a Data Domain system, AFTD, or tape.

5. Start or schedule the policy.

Performing a disaster recovery of the VMware Backup Appliance

Note

For any disaster recovery, you must repeat any changes previously made to the
configuration files. For example, the changes performed in the section Restrict
mapping of datastores on page 235.

Procedure
1. Redeploy the VMware Backup Appliance with the same network configuration
that was used at the time of the checkpoint. Use the Override button within
the EMC Backup and Recovery Configure window.

Note

Ensure that the password for the system that you plan to recover to matches
the password that was defined for the system when the checkpoint was taken.

2. Re-register the proxies with the redeployed VMware Backup Appliance by

running the following command from each external proxy, or reboot the external
proxy:
/usr/local/avamarclient/etc/initproxyappliance.sh start

3. Use NMC to connect to the NetWorker server, and then select the Devices tab
in Administration GUI.
4. In the left pane, select VMware Backup Appliance.
The backup appliances display in the right pane.
5. In the right pane, right-click the VMware Backup Appliance that you want to
recover, and then select Start VBA Recover for Checkpoints, as shown in the
following figure.

Performing a disaster recovery of the VMware Backup Appliance 299

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Figure 162 Starting a VMware Backup Appliance disaster recovery

A list of checkpoint backups displays.

6. Select the checkpoint backup to which you want to roll back, and then click OK.
After you click OK, the following events occur:
l The status of the VMware Backup Appliance changes to recover pending,
and the recovery takes 10-15 minutes to complete.
l Upon successful recovery, the status of the VMware Backup Appliance
changes to query pending.
l After 10 minutes, Cross sync generates the following events in NMC:
Cross sync with appliance name VMware Backup Appliance
is started.
Cross sync with appliance name VMware Backups Appliance
is successful for configuration and backups.
l The status of the VMware Backup Appliance changes to Success.

7. Check for restores of old backups and that the policies are intact as per the
checkpoint.

Complete disaster recovery of the VMware Backup Appliance and the Data
Domain or tape device
The following sections describe the steps that are required to a complete disaster
recovery, where you need to restore both the connection to the VMware Backup
Appliance, and the Data Domain or tape device that has completely failed.

Prerequisites for performing a complete disaster recovery

You can only run a complete disaster recovery after performing the following
prerequisites:
l Create regular checkpoint backups of the VMware Backup Appliance, as described
in the section Preparing the VMware Backup appliance for disaster recovery on
page 298.
l Clone the backups to a secondary Data Domain or tape device.

300 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Performing a complete disaster recovery

The following steps describe how to perform a complete disaster recovery of the
VMware Backup Appliance.
Procedure
1. Redeploy the VMware Backup Appliance with the same network configuration
that was used at the time of the checkpoint. Use the Override button within
the EMC Backup and Recovery Configure window.

Note

Ensure that the password for the system that you plan to recover to matches
the password that was defined for the system when the checkpoint was taken.

2. Re-register the proxies with the redeployed VMware Backup Appliance by

running the following command from each external proxy, or reboot the external
proxy:
/usr/local/avamarclient/etc/initproxyappliance.sh start

3. Use NMC to connect to the NetWorker server, and then select the Devices tab
in Administration GUI.
4. In the left pane, select VMware Backup Appliance.
The backup appliances display in the right pane.
5. In the right pane, right-click the VMware Backup Appliance that you want to
recover, and then select Start VBA Recover for Checkpoints, as shown in the
following figure.
Figure 163 Starting a VMware Backup Appliance disaster recovery

A list of checkpoint backups displays.

6. Select the checkpoint backup that you want to rollback to, and click OK.
7. Unmount the volumes pointing to the primary Data Domain device that has
failed.

Results
After performing these steps, you can now replace the primary Data Domain device
and either configure NetWorker Data Domain Boost devices the same way you set up

Complete disaster recovery of the VMware Backup Appliance and the Data Domain or tape device 301
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

the devices prior to the failure, or create new Data Domain Boost devices and adapt
your VMware policy and pools accordingly.

Recovery from a secondary site

When you clone a VM or VMDK backup to a secondary site with its own vCenter and
VMware Backup appliance, and the secondary site shares the same NetWorker server
as the primary site, you can recover data from the secondary site. This procedure is
particularly useful to recover data to a different vCenter when the primary site
becomes unavailable, or when restoring backups on the same vCenter using a
different VMware Backup Appliance.
This feature allows you to perform restores for all backups using any available VMware
Backup Appliance on any available vCenter as long as they are connected to the same
NetWorker server where the backup was performed.
Procedure
1. Select the Restore tab in the EMC Backup and Recovery user interface in the
vSphere Web Client.
2. From the Restore points from list, select the VMware Backup Appliance that
contains the required backup(s).
The Appliance Credentials dialog displays.
Figure 164 Entering appliance credentials

3. Type the username and password for the VMware Backup Appliance, and click
OK.
4. Browse restores from the VMware Backup Appliance and select the VMs/
VMDKs that you want to restore to the new location. Performing a FULLVM
restore on page 277 provides more information.

302 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Best practices and troubleshooting

This section provides best practices and troubleshooting information for the
NetWorker VMware Protection solution.

Performance and scalability

Performance and scalability of the NetWorker VMware Protection solution depends
on several factors, including which VMware Backup Appliance you deploy, the number
of vCenter servers and proxies, and whether you perform a large number of
concurrent Virtual Machine backups. The following table provides these scalability
factors.

Table 30 Scalability Factors

Component Recommended count Notes

VMs per VMware Backup 800-1000 VMs Given an average size of
appliance (Data Domain 20-30 GB per Virtual
backup, no external proxy) Machine, the 0.5 TB OVA can
accommodate a maximum of
800-1000 Virtual Machines,
when you back up to a Data
Domain device. One VMware
Backup Appliance can run 8
sessions in parallel.
Considering the Virtual
Machine size and data change
rate, a VMware Backup
Appliance can complete a
backup of 800-1000 Virtual
Machines within 24 hours.

VMs per VMware Backup VMware Backup Appliance

appliance (Data Domain + 5 external proxies can
backup + 5 external proxies, backup 1000 Virtual Machines
48 concurrent sessions in approximately 8 hours.

VMware Backup appliance per 3 or lower Better performance is

vCenter observed with a single
vCenter processing 48
concurrent sessions. When
you perform backups from
multiple VMware Backup
Appliances, EMC
recommends that you stagger
the backup to reduce the load
on vCenter.

Proxies per vCenter 5 Each VMware Backup

Appliance has one internal
proxy that can handle 8
concurrent sessions, and the
external proxy adds 8 more
concurrent sessions.

Best practices and troubleshooting 303

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 30 Scalability Factors (continued)

Component Recommended count Notes

Therefore, use 1 VMware
Backup Appliance and 5
external proxies.

Note

EMC recommends that you

disable the internal proxy for
the VMware Backup
Appliance if you will back up
more than 100 Virtual
Machines.

VMs per policy 200 or lower A single policy can scale up to

200 Virtual Machines. If more
than 48 Virtual Machines per
policy, the remaining Virtual
Machines will be queued
during backup.

VMs per restore 16 More than 16 Virtual

Machines may result in NBD
based restore due to VMware
API limitations.

Files/directories per FLR Maximum of 5000 FLR restore may be

significantly impacted when
there are more than 5000
files to be restored.

A VMware Backup Appliance can backup up to 8 Virtual Machines in parallel. If you

want to run up to 48 Virtual Machines backups in parallel, then add up to 5 external
proxies. Each external proxy can backup up to 8 Virtual Machines.
To achieve the best concurrent backup performance in a setup that requires additional
vCenters, VMware Backup Appliances or proxies, EMC recommends using 1 VMware
Backup Appliance + 5 External proxies per vCenter. The following tables provide
information on expected performance for different setups.

Table 31 Maximum concurrent sessions per VMware Backup Appliance

Deployed per vCenter Maximum concurrent sessions

1 VMware Backup Appliance 8

1 VMware Backup Appliance (internal proxy disabled) 8

+ 1 External Proxy

1 VMware Backup Appliance (internal proxy disabled) 16

+ 2 External proxies

1 VMware Backup Appliance (internal proxy disabled) 24

+ 3 External proxies

1 VMware Backup Appliance (internal proxy disabled) 32

+ 4 External proxies

304 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Table 31 Maximum concurrent sessions per VMware Backup Appliance (continued)

Deployed per vCenter Maximum concurrent sessions

1 VMware Backup Appliance (internal proxy disabled) 40
+ 5 External proxies

2 VMware Backup Appliance (internal proxy disabled) 16

+1 External proxy

Backups from the VMware Backup Appliance and external proxy create sessions with
NetWorker devices. The count of sessions is driven by the number of appliances,
external proxies, clone jobs and other backups running through this server. Every
VMware Backup Appliance and external proxy can run up to 8 sessions. If using
external proxies, EMC recommends that you disable the internal proxy on the VMware
Backup Appliance. The values calculated in the table above reflects a disabled internal
storage.

Table 32 Concurrency/parallelism recommendations

Component Concurrency count Notes

vCenter 50 concurrent sessions EMC recommends a maximum
of 50 concurrent virtual
machine backups per
vCenter.

External proxy 8 concurrent hotadd sessions External proxy has one SCSI
of VMDKs controller which limits the
concurrent hotadd sessions to
8 per external proxy.

Proxies per vCenter 6 vCenter achieves good

performance with 50
concurrent sessions as
indicated in the
recommendation above. Each
external proxy adds 8
concurrent sessions.
Therefore, using one VMware
Backup appliance (with
internal proxies disabled) and
6 external proxies will enable
you to reach 48 concurrent
sessions.

VMware Backup Appliance best practices

Observe the following best practices when using NetWorker with the VMware Backup
Appliance.

Note

For more best practices related specifically to the deployment of the VMware Backup
Appliance in new or upgraded installations of NetWorker, review the section VMware
Backup Appliance requirements.

VMware Backup Appliance best practices 305

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

l Ensure that the NetWorker server and storage node are at the same version, and
that the VMware Backup Appliance you deploy is compatible with this version, for
example, NetWorker 18.1 with OVA 1.5.1.7.
l Use Hotadd transport mode for faster backups and restores and less exposure to
network routing, firewall, and SSL certificate issues. To support Hotadd mode,
deploy the VMware Backup Appliance on an ESXi host that has a path to the
storage that holds the target virtual disk(s) for backup. In environments that use
the older VMFSv3 format datastore, deploy the proxy on the datastore with the
largest block size.

Note

Hotadd mode requires VMware hardware version 7 or later. Ensure all Virtual
Machines that you want to back up are using Virtual Machine hardware version 7
or later.

For sites that contain a large number of Virtual Machines that do not support
Hotadd requirements, NBD backups will be used. This can cause congestion on the
ESXi host management network. Plan your backup network carefully for large
scale NBD installs. You may consider configuring one of the following options:
n Set up Management network redundancy.
n Set up backup network to ESXi for NBD.
n Set up storage heartbeats. http://www.vmware.com/files/pdf/techpaper/
vmw-vsphere-high-availability.pdf provides more information.
l Avoid deploying VMs with IDE virtual disks; using IDE virtual disks degrades
backup performance. Use SCSI virtual disks instead whenever possible.

Note

You cannot use hotadd mode with IDE Virtual disks and therefore backup of these
disks will be performed using NBD mode.
l During policy configuration, assign clients to a policy based on logical grouping to
allow for better scheduling of backups that will help you avoid resource contention
and create more organized logs for review.
l It is recommended that you perform regular checkpoint backups to protect the
VMware metadata in your environment. You can schedule daily checkpoint
discover and checkpoint backup actions for a VMware Protection Policy, within
NetWorker.
l When you plan the backups, ensure that NetWorker VMware Protection supports
the disk types that you use in the environment. Currently, NetWorker VMware
Protection does not support the following disk types:
n Independent (persistent and non-persistent)
n RDM Independent - Virtual Compatibility Mode
n RDM Physical Compatibility Mode
l When you enable Change Block Tracking (CBT) NetWorker can achieve faster
incremental backup performance. The default VMware Backup Appliance
configuration has a threshold of 25% change per client, which means that if the
particular Virtual Machine has changed more than 25% since the last backup,
NetWorker will perform a level full backup. In order to support Changed Block
Tracking (CBT):
n Ensure that all Virtual Machines run VMware hardware version 7 or higher.

306 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

n If you add a disk or dynamically expand a disk on a Virtual Machine, you must
take a new full backup for CBT to function.
For Incremental backups with CBT, remove any existing snapshots of a Virtual
Machine before you add the VMware Backup Appliance.

Note

Adding containers or Virtual Machines to a policy will automatically enable CBT.

l When backing up thin-provisioned Virtual Machines or disks for Virtual Machines
on NFS datastores, an NFS datastore recovery does not preserve thin
provisioning. VMware knowledge base article 1035096 at http://
kb.vmware.com/kb/1035096 provides more information.
l Install VMware Tools on each Virtual Machine that you want to back up by using
the EMC Backup and Recovery user interface in the vSphere Web Client. VMware
Tools adds additional backup capability that quiesces certain processes on the
guest OS prior to backup. Some features in File Level Restore also require VMware
Tools.
l Conflicting vSphere Web Client plug-ins can cause unexpected behavior with the
EMC Backup and Recovery user interface in the vSphere Web Client. Examples
include the VDP plug-in, and the HP Insight Manager plug-in. VMware knowledge
base article 1025360 at http://kb.vmware.com/kb/1025360 provides the
instructions to remove conflicting plugins.
l EMC recommends that you set an appropriate NetWorker server/storage
parallelism value, according to the available resources, to reduce queuing. For
example, a VMware Backup Appliance with 5 external proxies and clones requires
more than 64 parallel sessions. Therefore, setting the parallelism for the
NetWorker server to 128 or higher (while also setting the server with 32+ GB
memory and 8+ CPUs) will suit such an environment. The NetWorker Performance
Optimization Planning Guide provides more details.
If you require a larger number of parallel image backups, also consider setting the
maximum number of vCenter SOAP sessions to larger value. Note that this
requires careful planning and additional resources on the vCenter Server You can
configure this by modifying the following line in the vCenter vpxd.cfg file:
<vmacore><soap><maxSessionCount> N </maxSessionCount></soap></
vmacore>
This applies specifically to SDK sessions as opposed to VI client sessions:
l Each Virtual Machine backup to a Data Domain system consumes more than one
session on the Data Domain device. The default device configuration is target
sessions=6 and max session=60, however EMC recommends that you
configure additional devices for more than 10 parallel backups.
l Virtual Machines with extremely high IO may face hangs during consolidation due
to the ESXi forced operation called synchronous consolidate. Plan your backups of
such Virtual Machines according to the amount of workload on the Virtual
Machine.
l When you work with the vCenter database either directly or by using scripts, do
not change the name attribute for the vmfolder object. VMware knowledge base
article at https://support.emc.com/kb/190755 provides more information.
l When you set up multiple devices locally on the NetWorker server, this can lead to
resource contention. Large VMware environments will have more stability when
most backup devices are set up on a remote storage node.

VMware Backup Appliance best practices 307

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

When you mount a backup or clone pool volume on a remote storage node, then
modify the client properties for the VMware Backup Appliance resource in
NetWorker to add the remote storage node names to the Storage nodes attribute
on the Globals (2 of 2) tab.
l Resource contention can occur at various points during the backup cycle. When
NetWorker runs larger policies issues due to contention of resources can occur,
which impact all running operations. Adjust your resources and times for other
larger policies to avoid overlaps, and avoid resource contention.
For example, you configure one pool named Bronze, with one device. If you set up
a policy where every day at 10 pm two policies called 'Bronze1' and 'Bronze2' with
400 clients each start writing to the device in the 'Bronze' pool, then the long wait
for device availability may cause unexpected delays or timeouts. To fix this, set the
policy start times 4 hours apart and add more devices, to allow for stable backups.

Limitations and unsupported features

Before you deploy the NetWorker VMware Protection solution with the VMware
Backup appliance, review the following limitations and unsupported features.

Note

Review the VMware limitations:

l vSphere 5.5—https://www.vmware.com/pdf/vsphere5/r55/vsphere-55-
configuration-maximums.pdf
l vSphere 6.0—https://www.vmware.com/pdf/vsphere6/r60/vsphere-60-
configuration-maximums.pdf

VMware Backup appliance versions must be the same when deploying multiple
VMware Backup appliances in same vCenter
When you deploy more than one VMware Backup appliance in your environment and
the appliances are registered to the same vCenter, then these VMware Backup
appliance versions must be the same.
Incremental backups across Data Domain systems not supported
Performing incremental backups across Data Domain systems is not supported for
VMware Backup appliance policies.
Recovery of virtual machine configured with EFI firmware fails to find operating
system during virtual machine startup
When a virtual machine is configured with EFI firmware, backup and recovery
completes successfully. However, when the restore is performed and the virtual
machine is powered on, the virtual machine fails to find an operating system during
startup. To work around this issue, perform an Instant Access recovery of the virtual
machine.
Cannot add Actions to workflows that have the same name in different policies
For traditional workflows, VMware allows you to use the same workflow name in
different policies. However, if you add such a workflow to a policy, you cannot add
actions to the workflow.
Datastore names cannot contain special characters
Using special characters in datastore names can cause problems with the Virtual
Backup appliance, such as failed backups and restores. Special characters include the
following: % & * $ # @ ! \ / : * ? " < > | ;, etc.

308 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

External proxy appliance must be at same version as VMware Backup appliance

Performing an image level recovery in the vSphere Web Client fails with error code
10002 when the external proxy is running an older awncomm version than the VMware
Backup appliance, due to the addition of the NW_VBA_NAME flag in later versions.
Ensure that the external proxy appliance is at the same version as the VMware Backup
appliance and if not, upgrade the external proxy. If you require an immediate recovery
in an environment with mixed versions, temporarily shut down all of the external
proxies while you start the Virtual Machine restore. This will ensure that the recovery
gets assigned to the VMware Backup appliance internal proxy. Knowledge base article
457952 available at http://support.emc.com provides more information.
Avamar image backups to Data Domain fail if proxies not added to DD Boost
Access list
Avamar VMware image backups to Data Domain fail with errors when you do not add
the proxies to the DD Boost access list.
To add the proxies to the DD Boost access list, run the following command: ddboost
access add clients client-list. Knowledge base article 453486 available at
http://support.emc.com provides more information.
FLR browse in EMC Data Protection Restore Client may not display second of
three disks
When you use the EMC Data Protection Restore Client to browse disks for FLR, the
second of three disks may not display due to partition detection failing for this specific
disk. The disk will display properly from the command line.
Knowledge base article 457783 at http://support.emc.com provides possible
workarounds and more information on this issue.
Data Domain SMT not supported
The NetWorker VMware Protection Solution does not support Data Domain SMT. You
can create different DDBoost users to segregate access to specific DD Boost devices.
However, DD Admin credentials are required for performing instant access and file-
level restore workflows.
Backups to Data Domain device over WAN may fail if TLS used
Backups to a DDBoost device over WAN occasionally fail when you use TLS. DDBoost
fails to establish a TLS connection to the Data Domain device due to an SSL
Handshake Failure. DDBoost can successfully connect to the same Data Domain
device when TLS is not used.
Do not use combination of FQDN and IP when registering vCenter server
When you register the vCenter server with the VMware Backup appliance and the
NetWorker server, ensure that you specify only the FQDN or only the IP in all
instances. Do not use a combination of the two.
VMware Backup appliance must be deployed to an ESX host managed by the
same vCenter you register the appliance to when using multiple vCenters
When you have multiple vCenters, you must deploy the VMware Backup appliance to
an ESX host that is managed by the same vCenter you register the appliance to.
Otherwise, a connection error message similar to the following appears: “Unable to
find this EBR in the vCenter inventory.”
Only hotadd and NBD transport modes supported
The NetWorker VMware Protection solution supports only the hotadd and NBD
transport modes. The hotadd mode is the default transport mode.

Limitations and unsupported features 309

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Higher default target session and max session values for VMware Backup
appliance
NetWorker creates the default VMware Backup appliance with the values target
session=50 and max session=200. These values are higher than normal default values
for a device created in NetWorker because each appliance or external proxy comes
with 8 proxy agents.
Backup of individual folders within a Virtual Machine is not supported
The NetWorker VMware Protection solution only supports image-level backup and
disk-level backup. You cannot perform backups of individual folders within the Virtual
Machine.
VMware View in the NetWorker Administration map view does not display when
configuration for Virtual Machines within the vCenter is incomplete
When you use VMware View, the map view does not appear when the configuration
for one or more Virtual Machines in the vCenter is incomplete. To avoid this issue,
remove the incomplete Virtual Machine configurations from vCenter.
I/O contention when all Virtual Machines on a single data store
I/O contention may occur during snapshot creation and backup read operations when
all Virtual Machines reside on a single datastore.
No automatic migration tool to move from previous solution to NetWorker
VMware Protection
An automatic migration tool to move from the previous Virtual Machine backup
solution to the NetWorker VMware Protection solution does not exist.
Only English keyboards supported in vSphere Web Client's EMC Backup and
Recovery user interface
The EMC Backup and Recovery user interface in the vSphere Web Client only
supports English language keyboards.

Configuration checklist
The following configuration checklist provides best practices and troubleshooting tips
that may help resolve some common issues.

Basic configuration
l Synchronize system time between vCenter, ESX/ESXi/vSphere, and the vProxy
appliance
l Assign IPs carefully — do not reuse any IP address
l Use FQDNs (Fully Qualified Domain Names) everywhere
l For any network related issue, confirm that forward and reverse DNS lookups
work for each host in the datazone.

Data Domain system configuration

l Upgrade all Data Domain systems to use DDOS version 5.6 and later.
l Ensure that the Data Domain system does not reach the MTree limit and max-
streams limit.
l Ensure that only devices from the same Data Domain system host appear in Data
Domain system pool when used in any Action.

310 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

NetWorker configuration
l Ensure that the relevant devices are mounted
l Wait until you successfully configure a policy before you run the policy.
l A message appears after successful registration in NMC.

VMware Backup Appliance configuration

l Supports configuration on thin disks.
l Use the EMC Backup and Recovery Configuration Utility to confirm that all
services on the VMware Backup Appliance except the backup scheduler are
running. Note that maintenance services will start between 24 to 48 hours after
booting up, or you can start maintenance services manually.
l To avoid slower recovery times , do not add more than 500 VMs to a VMware
Backup Appliance.
l Ensure that the VMware Backup Appliance still has space left for backups.
l VMware snapshot for backup is not supported for independent disks.

IPv6 considerations
The following considerations apply when using IPv6 instead of IPv4 for NetWorker
VMware Protection.
Register with FQDN instead of IP in EMC Backup and Recovery Configuration
Utility
During registration of the VMware Backup Appliance in the EMC Backup and
Recovery Configuration Utility window, if using IPv6 do not specify the IPv6
address. Use the FQDN of the vCenter server to register the appliance instead.
Additional zeros display in IPv6 address in EMC Backup and Recovery
Configuration Utility
The IPv6 static address tab in the EMC Backup and Recovery Configuration Utility
window displays additional zeros in the address.
Remove the extra zeros, or re-type the correct IPv6 address prior to clicking Next.
Emergency restore (Direct to host recovery) unavailable
Emergency restore, also referred to as Direct to host recovery, is currently unavailable
in an IPv6 environment.

VMware Backup Appliance installation

If you have problems with the VMware Backup Appliance installation:
l Confirm that all of the software applications meet the minimum software
requirements. System requirements on page 209 provides more information.
l Confirm that the hardware meets the minimum hardware requirements (see
System requirements on page 209 provides more information.
l Confirm that DNS is properly configured for the VMware Backup Appliance (see
Pre-installation requirements on page 214 provides more information.

IPv6 considerations 311

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

AV-NetWorker Communicator (avnwcomm) timeout

The default timeout for avnwcomm communication between the proxy and the
NetWorker server is two minutes.
During the backup window, the following issues may cause a delayed response from
NetWorker, leading to failures during backup and restore operations:
l Devices unavailable
l Low server parallelism
l Peer information issues
l DNS problems
l Offsite deployments where the VMware Backup appliance node or proxy are on a
different site from the NetWorker server
For sites experiencing delays, you can tune the avnwcomm.cmd inactivity timeout to
allow for longer wait times, for example 5 minutes, using the following procedure.
1. Run the following command to verify the version. /usr/local/
avamarclient/bin/avnwcomm --version
2. Create a file on the VMware Backup appliance node and external proxy called
avnwcomm.cmd under /usr/local/avamarclient/var/.
3. Edit avnwcomm.cmd to add the following: --nw_init_timeout=300
4. Ensure you have the correct permissions by running: chmod 755 /usr/local/
avamarclient/var/avnwcomm.cmd

Log in to the EMC Backup and Recovery Console as admin instead of root
When you use ssh to connect or login to the EMC Backup and Recovery Console,
ensure that you login as the admin user instead of root. Direct login as the root user is
not permitted.
EMC does not recommend that you modify the ssh configuration file in /etc/ssh so
that a user can ssh into the appliance directly as root. Changes this file can result in
future upgrade failures.
After you ssh to the Console as admin, you can then switch to the root user, as
shown in the following example:

# ssh <VBA-host> -l admin

Password:
#su
Password:

If you use the vSphere Client to connect to the EMC Backup and Recovery Console,
you can log in as the root user.

Note

The password for the admin user is the same as the password that you specified in the
EMC Backup and Recovery Configure window during the initial installation of the
VMware Backup Appliance.

312 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Launching the Dell EMC Data Protection Restore Client after upgrade on
Mozilla Firefox browser
After upgrading the VMware Backup Appliance from a NetWorker 8.2 release to
NetWorker 9.0 and later, the Dell EMC Data Protection Restore Client window
might not launch when using the Mozilla Firefox browser.
If you cannot launch the Dell EMC Data Protection Restore Client window, run the
following commands on the VMware Backup Appliance as the root user:
l /usr/java/latest/bin/keytool -delete -alias tomcat -storepass
changeit
l /usr/java/latest/bin/keytool -genkeypair -v -alias tomcat -keyalg
RSA -sigalg SHA256withRSA -keystore /root/.keystore -storepass
changeit -keypass changeit -validity 3650 -dname
"CN=localhost.localdom, OU=Avamar, O=EMC, L=Irvine, S=California,
C=US"
l emwebapp.sh --restart
If you use the Mozilla Firefox browser on a Linux machine and are unable to browse
the backups even after you upgrade the browser to the latest version, an error
message similar to the following might appear: sec_error_ca_cert_invalid
issue
To resolve this issue, perform the following steps:
1. Open the Mozilla Firefox browser.
2. In the Location bar, type about:config and press Enter.
You may see a warning that says This might void your warranty!
Click I'll be careful, I promise! to continue to the about:config page.
3. Set security.use_mozillapkix_verification to True, if the value is set to False.

Launching the EMC Backup and Recovery Configuration Utility after upgrade
on Mozilla Firefox browser
After upgrading the VMware Backup Appliance from a NetWorker 8.2 release to
NetWorker 9.0.1 and later, the EMC Backup and Recovery Configuration Utility
window may not launch when using the Mozilla Firefox browser.
If you cannot launch the EMC Backup and Recovery Configuration Utility window,
perform the following:
1. Login via SSH to the VMware Backup Appliance Console as the admin user.
2. Switch to the root user by running the following command:

su -
Password:
3. Run the following commands on the VMware Backup Appliance:

/usr/java/latest/bin/keytool -delete -alias tomcat -storepass

changeit /usr/java/latest/bin/keytool -genkeypair -v -alias tomcat
-keyalg RSA -sigalg
SHA256withRSA -keystore /root/.keystore -storepass changeit -
keypass changeit -validity 3650 -dname "CN=localhost.localdom,

Launching the Dell EMC Data Protection Restore Client after upgrade on Mozilla Firefox browser 313
NetWorker VMware Protection with the VMware Backup Appliance (legacy)

OU=Avamar, O=EMC, L=Irvine, S=California, C=US"emwebapp.sh --

restart

Restart the Enterprise Manager Web Application (emwebapp)

Use the following steps to restart emwebapp.
1. Log into the Console, and then type:

emwebapp.sh --stop
emwebapp.sh --start
2. Restart the EMC Backup and Recovery database by running:

emwebapp.sh --stop
su – admin
ebrdbmaint.pl --startdb
exit
emwebapp.sh --start
3. Patch the EMC Backup and Recovery server by running:

emwebapp.sh --stop
cd /usr/local/avamar/lib/ebr
mv ebr-server.war ebr-server.war.orig
4. Use SFTP to upload the new war file to this location:
emwebapp.sh --start*

Note

When you use ssh to connect or log in to the EMC Backup and Recovery Console in
the vSphere Client, ensure that you login as admin instead of root. Log in to the EMC
Backup and Recovery Console as admin instead of root on page 312 provides more
information.

VMware Backup Appliance Log file locations

Review the following VMware Backup Appliance log file locations:
l Tomcat logs—/usr/local/avamar-tomcat/logs catalina.out for HTTP
request and respond at high level
l EMC Backup and Recovery server logs—/usr/local/avamar/var/ebr/
server_log/ebr-server.log for specific EMC Backup and Recovery
activities
l MC logs—/usr/local/avamar/var/mc/server_log
l MC Soap service logs—/usr/local/avamar/var/mc/server_log/
axis2.log
l Boot logs—/usr/local/avamar/var/av_boot.log
/usr/local/avamar/var/av_boot_err.log
l EMC Backup and Recovery configure or registration with EMC Backup and
Recovery appliance logs—/usr/local/avamar/var/ebr/server_log/
ebr-configure.log
l File Level Recovery logs—/usr/local/avamar/var/flr/server_log
l NetWorker log file location—/nsr/logs/

314 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

Collecting log files

To collect all log files on the EMC Backup and Recovery appliance:
1. Connect to the EMC Backup and Recovery Configure window, as shown in Post-
installation configuration on page 240.
2. Open the Log Collector tab.
Three sections appear:
l All EBR appliance logs
l Client logs
l Configurations
3. On the Status tab, click Collect Logs.
4. Click Download to save the log files to the local machine that you used to open
the EMC Backup and Recovery Configure window.

Enabling low-level logging of NetWorker web server on Windows systems

To enable low-level logging, log into the NetWorker server and perform the following
steps:
1. Open a command prompt and run cmd.exe.
2. Use Task Manager to get the pid of nsrvmwsd.
3. CD to networker-install-dir > \nsr\bin.
4. Run dbgcommand -p > <nsrvmwsd-pid > > Debug=11.

NetWorker operations
The following troubleshooting items provide some direction on how to identify and
resolve common issues with NetWorker and VMware Protection Policies.

VMware Protection Policy fails for manually created client resource with DataDomain backup
attribute enabled
When you manually create a client resource and enable the DataDomain backup
attribute (using nsradmin or the NMC Client Properties window), the default VMware
Protection Policy fails with the following error:

NWP_LOG_OUTPUT: NW Client Plugin: ABORT session operation

successful. Reason for abort: nwp_start_backup_session_helper: no
matching IP interface data domain devices for save of client
clientname; check storage nodes, devices or pools

If this occurs, unselect/disable the DataDomain backup attribute on the manually

created client resource.

“No proxies running on VBA {appliance name} for backing up VM {VM name}”
When the avagent is not running, or no proxies are running, this error appears in the
VMware Protection Policy details window in NMC.
If you see this error, log in as root from the EMC Backup and Recovery Console in the
vSphere Client and invoke service avagent restart:
/etc/init.d/avagent restart

NetWorker operations 315

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

NetWorker web services timeout

Due to the extended time required to perform larger operations such as cross-sync,
NetWorker web services may time out.
For example, web services may request a clean-up of a large amount of data on the
VMware Backup Appliance, for which the time required to complete the operation
exceeds the timeout setting. When a VMware Backup Appliance communication
timeout occurs, an "operation timed out" error message appears.
To fix VMware Backup Appliance communication timeouts, you can set two
environment variables on the NetWorker server -- one for connection attempts to the
VMware Backup Appliance, and the other for requests.
NSR_VBA_CONNECT_TIMEOUT=900
NSR_VBA_REQUEST_TIMEOUT=2400
If your timeout values are lower than these numbers, it is recommended to these
values.

Note

Values are in seconds. The maximum value permitted for

NSR_VBA_CONNECT_TIMEOUT is 1200 and the maximum value permitted for
NSR_VBA_REQUEST_TIMEOUT is 3600.

Changes to these values may depend on the operating system of the NetWorker
server. The sections "Setting environment variables on UNIX" and "Setting
environment variables on Windows systems" in the NetWorker Administration Guide
provide more information. If VMware Backup Appliance registration fails with the
Networker server after the initial deployment and registration, you can also set
NSR_VBA_CONNECT_TIMEOUT at the operating system level for successful
registration.
On Linux, login to the NetWorker server and perform the following:
1. Run # printenv | grep NSR_VBA_CONNECT_TIMEOUT export
NSR_VBA_CONNECT_TIMEOUT=900.
2. Restart NetWorker services by using the command /etc/init.d/networker
restart.
3. Run emwebapp.sh --restart on the VMware Backup Appliance.
To re-register the VMware Backup Appliance on Windows:
1. Right-click My Computer > Select Environment Variables.
2. Add a new variable NSR_VBA_CONNECT_TIMEOUT with the value 900.
3. Restart NetWorker services on the NetWorker server and run emwebapp.sh --
restart on the VMware Backup Appliance.

vCenter server operations

The following troubleshooting items provide some direction on how to identify and
resolve common issues from the vCenter server.

Clear All EMC Backup and Recovery plug-ins

1. Log into vCenter Server's MOB at http://vcenter-server/mob.

316 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

2. Click on the content link.

3. Click on ExtensionManager link.
4. Click on the UnregisterExtension link.
5. Enter the value com.emc.networker.ebr and click the Invoke Method link.

Enable HTTP access from EMC Backup and Recovery

1. Log in to the vCenter server console, then type:
vi /var/lib/vmware/vsphere-client/webclient.properties
2. Ensure that the output contains a line similar to allowHttp=true.

vSphere Client operations

The following troubleshooting items describe how to identify and resolve common
issues that occur with EMC Backup and Recovery Console from the vSphere Client, or
the EMC Backup and Recovery user interface in the vSphere Web Client.

Time synchronization error

A time synchronization error can occur when launching the EMC Backup and
Recovery user interface in the vSphere Web Client in the following scenarios:
l When you configure the EMC Backup and Recovery appliance to synchronize its
time with the ESX server on which the appliance runs.
l When the vCenter server is a VM, and runs on an ESX server that differs from the
ESX server that hosts the EMC Backup and Recovery appliance.
In such environments, if the times differ on the two ESX servers, and the vCenter
server is not set up to synchronize with the ESX server it runs on, then the following
errors appear in the vSphere Web Client interface:

The most recent request has been rejected by the server.

The most common cause for this error is that the times on the EMC
Backup and Recovery appliance and your SSO server are not in sync

To fix this issue:

1. Verify that the times match on all the ESX servers in your environment. You can
configure the time settings in the vCenter UI. EMC recommends that you
configure the time settings to use NTP. The VMware knowledgebase article
2012069 provides details on configuring NTP on ESX/ESXi hosts using the
vSphere Client.
2. On your vCenter system, ensure that it is configured to synchronize its time with
the ESX server it is running on by running the following:
vmware-toolbox-cmd timesync enable
3. Verify that the time on your EMC Backup and Recovery appliance and your
vCenter server are the same by running the date command on each.

Note

Allow a couple of minutes after making the changes for times to merge.

vSphere Client operations 317

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

4. Log in to the vSphere Web Client. If the time synchronization message does not
appear when you launch the EMC Backup and Recovery user interface, the times
have been synchronized successfully.

Restart vSphere Web Client Server

To restart the vSphere Web Client server:
1. Log into the vCenter server console, then type:
cd /usr/lib/vmware-vsphere-client
2. Run ./vsphere-client stop.
3. Run ./vsphere-client start.

Start user interface does not display as available in vSphere Web Client
If the user interface does not display as available in the vSphere Web Client, log into
vCenter and restart the vSphere Client Services by running the following from a
command prompt:

cd /usr/lib/vmware-vsphere-client
./vsphere-client stop
./vsphere-client start

When you deploy a VM, do not change the default network (VM Network) provided by
the wizard. After the deployment completes and prior to powering on the VM,
reconfigure the VM to use the appropriate network if VM Network is not correct. If
you change the network in the wizard, EMC Backup and Recovery looks for eth1
instead of eth0, and network connectivity fails.

Launching the Console in the vSphere Web Client to reboot the VM

When you log into the vSphere Web client and launch the Console for the EMC
Backup and Recovery appliance, a delay of several minutes may occur while the VM
reboots. A message similar to the following appears in the output:

Identity added: /home/dpn/.ssh/dpnid (/home/dpn/.ssh/dpnid)

If you see this message, do not shutdown the VM, and allow time for the reboot to
complete.

The EMC Backup and Recovery appliance is not responding. Please try your request again
If you were previously able to connect to EMC Backup and Recovery and this message
appears, check the following:
l Confirm that the user name or password used to validate EMC Backup and
Recovery to the vCenter Server has not changed. Only one user account and
password are used for EMC Backup and Recovery validation. This is configured
through the EMC Backup and Recovery Configure window.
l Confirm that the name and IP address of the appliance have not changed since the
initial EMC Backup and Recovery installation. DNS Configuration on page 215
provides additional information.

Integrity Check
After you start an integrity check, a delay of several seconds may occur before the
“EBR: Integrity Check” task shows up in the Recent Tasks pane of the EMC Backup

318 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

and Recovery user interface in the vSphere Web Client. Similarly, when you cancel an
integrity check, a delay of several seconds may occur before the task is cancelled.
In some cases (for example, when the integrity check progress is above 90%), the
integrity check may actually complete before the cancel operation completes. Even
when the integrity check completes successfully, the Task Console may still show an
error indicating that the integrity check was cancelled.
If you knew that the Integrity Check Status of the appliance (shown on the Reports
tab) was “Out of Date” before you started the integrity check, then you can look at
the status immediately after you cancel the job to see if the cancel operation
succeeded. If the Integrity Check Status is “Normal,” then the check was successful.
If the status is “Out of Date,” then the check was cancelled.

Backup operations
The following troubleshooting items provide some direction on how to identify and
resolve common issues with NetWorker VMware Protection backups for the VMware
Backup Appliance (VBA).

Backups fail with external proxy after upgrading from NetWorker 8.1.x to 18.1
Backups may fail with the external proxy after an upgrade from NetWorker 8.1.x to
version 18.1 has occurred.
If this happens, delete the peer information for the external proxy from the NetWorker
server.

Backups fail when EMC Backup and Recovery plug-in registers with an incorrect version string
in vCenter
Backups may fail when the EMC Backup and Recovery plug-in registers with an
incorrect version string in vCenter. Additionally, EMC Backup and Recovery cannot
co-exist with VMware VDP or any third-party backup plug-in in the same vCenter. If a
conflict occurs, then unregister the EMC Backup and Recovery plug-in extension from
the managed object browser (MOB):
1. Navigate to http://vcenter-ip/mob.
2. In the Properties table, select the content link.
3. Select Extension Manager and verify that the Properties table lists
“com.vmware.ebr2”.
4. From the Methods table, select UnregisterExtension.
5. Type com.vmware.ebr2 and select Invoke Method.

Note

This name will be different if removing VDP or a third party backup plug-in.
6. Verify in Extension Manager that the plug-in is no longer listed in the Properties
table, and then restart vCenter services or the vCenter server.
7. Restart emwebapp on the EMC Backup and Recovery appliance by using the
command emwebapp.sh --restart.

“Loading backup job data”

This message can appear for up to five minutes when you select a large number of
VMs (approximately 100 VMs) for a single backup job. This issue can also apply to
lock/unlock, refresh, or delete actions for large jobs. This is expected behavior when

Backup operations 319

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

you select a very large number of jobs. This message disappears when the action is
completed, which can take up to five minutes.

“Unable to add client {client name} to the EMC Backup and Recovery appliance while creating
backup job {backupjob name}.”
This error can appear when there is a duplicate client name on the vApp container or
the ESX/ESXi host. In this case only one backup job is added. Resolve any duplicate
client names.

“The following items could not be located and were not selected {client name}.”
This error can occur when the backed up VM(s) cannot be located during Edit of a
backup job. This is a known issue.

Windows 2008 R2 VMs may fail to backup with “disk.EnableUUID” configured to “true.”
Windows 2008 R2 backups may fail if the VM is configured with the disk.EnableUUID
parameter set to true. To correct this problem, manually update the vmx configuration
parameter disk.EnableUUID to false by using the vSphere Web Client:
1. Shut down the VM by right clicking the VM and selecting Shut Down Guest OS.
2. Right click the VM and select Edit Settings.
3. Click VM Options.
4. Expand the Advanced section and click Edit Configuration.
5. Locate the name disk.EnableUUId and set the value to false.
6. Click OK on the next two pages.
7. Right click the VM and select Power On.
After you update the configuration parameter, the backups of the Windows 2008 R2
VM should succeed.

Backup fails if EMC Backup and Recovery does not have sufficient datastore capacity
Scheduled backups fail at 92% complete if there is insufficient datastore capacity. If
you configured the EMC Backup and Recovery datastore with thin provisioning and
maximum capacity has not been reached, then add additional storage resources. If you
configured the EMC Backup and Recovery datastore with thick provisioning and it is
at full capacity, see EMC Backup and Recovery Capacity Management on page 292.

Backup fails if VM is enabled with VMware Fault Tolerance

When you enable Fault Tolerance for a VM, the backup fails. This is expected
behavior; EMC Backup and Recovery does not support backing up VMs with Fault
Tolerance enabled.

When VMs are moved in or out of different cluster groups, associated backup sources may be
lost
When you move hosts into clusters with the option to retain the resource pools and
vApps, the containers get recreated, not copied. As a result, the container is no longer
the same container even though the name is the same. To resolve this issue, validate
or recreate any backup jobs that protect containers after moving hosts in or out of a
cluster.

320 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

After an unexpected shutdown, recent backup jobs and backups are lost
When an unexpected shutdown occurs, the VMware Backup appliance performs a
rollback to the last validated checkpoint. This is expected behavior.

vMotion operations are not allowed during active backup operations

The vSphere vMotion feature enables the live migration of running virtual machines
from one physical server to another. You cannot run vMotion operations on the vProxy
appliance or VMware Backup appliance during active backup operations. This is
expected behavior. Wait until all backup operations have completed prior to
performing a vMotion operation.

Backups fail if certain characters are used in the virtual machine name, datastore, folder, or
datacenter names
When you use spaces or special characters in the virtual machine name, datastore,
folder, or datacenter names, the .vmx file is not included in the backup. The vProxy
appliance and VMware Backup appliance do not back up objects that include the
following special characters, in the format of character/escape sequence:
l & %26
l + %2B
l / %2F
l = %3D
l ? %3F
l % %25
l \ %5C
l ~ %7E
l ] %5D

Restore operations
The following troubleshooting items describe how to identify and resolve some
common issues with restores.

Restore to new virtual machine not available for backups that included physical RDM disks
When you back up a virtual machine that contains both virtual disks and physical Raw
Device Mapping (RDM) disks, the backup successfully processes the virtual disks and
bypasses the RDM disks, which are not supported for backup. However, when you
restore data from one of these backups, you cannot restore the data to a new virtual
machine because data residing on the physical RDM disks that were bypassed during
the backup cannot be restored.
If you need to restore the data to a new virtual machine, perform the following:
1. Manually create a new virtual machine in vCenter. This new virtual machine must
contain the same number of virtual disks as the original virtual machine from which
the backup was taken.
2. Manually add the new virtual machine to NetWorker.

Restore operations 321

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

3. Restore the data to this virtual machine.

Restore tab shows backups taken after checkpoint backup as "not available"
When you complete a successful disaster recovery of the VMware Backup appliance,
and then attempt to restore a backup performed after the last checkpoint backup, the
Restore tab in the EMC Backup and Recovery user interface in the vSphere Web
Client displays these backups as "not available." This occurs because no account for
these backups exists, since the client or VM was added to the policy after the
checkpoint backup.
When you add the client or VM back into a policy, backups display correctly with a
valid path in the Restore tab.

Message appears during FLR indicating “error finding vm by ipAddr” when you do not install
VMware Tools
You must install VMware Tools to perform FLR. When you do not install VMware
Tools, a message appears indicating the restore client is unable to find a backup of a
VM by IP.

Message appears indicating “Login failed. Cannot locate vm in vCenter.”

This error can occur when you attempt to connect to the EMC Data Protection
Restore Client from a host that has not been backed up by the VMware Backup
appliance
Log into a virtual machine that has been backed up by the VMware Backup appliance,
and then connect to the restore client.

Restore tab shows a “Loading backups” message and is slow to load

It typically takes two seconds per VM backup to load each of the backups on the
Restore tab. This is expected behavior.

Restore tab is slow to load or refresh

If there is a large number of VMs, then the Restore tab may be slow to load or refresh.
For example, when you have approximately 100 VMs, the Restore tab can take up to
four and a half minutes to load.

Adding external proxies

The VMware Backup appliance has 8 internal proxies. A proxy can only do one backup
or restore at a time.
If you need more proxies, then deploy an external proxy OVA. The section Proxy
assignment for backup and recovery on page 217 provides information.

Creating and analyzing crashes on Windows 2008 R2

1. Update the registry with the new key provided at http://msdn.microsoft.com/en-
us/library/bb787181(VS.85).aspx.
Using the recommended values, the dump file gets created in C:\Users
\Administrator\AppData\Local\CrashDumps
2. Enable full crash dumps.

322 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection with the VMware Backup Appliance (legacy)

3. File an Open dump file in windbg.

4. To retrieve the full information, type analyze --v in the bottom command window.

Changing the Data Domain Boost password

When you change the password of the Data Domain Boost user, perform the following
steps to ensure you also make the change on the VMware Backup appliance.
1. Update the password in the NMC Device Properties window, or in the Device
Configuration wizard, for all devices belonging to the Data Domain host for which
the password was changed.
2. Run the following command on the EMC Backup and Recovery Console in the
vSphere Client:
mccli dd edit --name=fqdn --password=newpassword --password-
confirm=newpassword --user-name=boostuser

Accessing Knowledge Base Articles

Additional troubleshooting information is available through the Featured VMware
Documentation Sets website at https://www.vmware.com/support/pubs/. Select
Support > Search Knowledge Base.

Changing the Data Domain Boost password 323

NetWorker VMware Protection with the VMware Backup Appliance (legacy)

324 NetWorker 18.1 VMware Integration Guide

CHAPTER 6
VADP Recovery (legacy)

Note

NetWorker 18.1 releases do not feature a new version of the VADP proxy. For VADP,
NetWorker 18.1 only supports recoveries that were configured in a previous release.
The NetWorker Online Compatibility Guide available on the Dell EMC Online Support
site at https://support.emc.com/products/1095_NetWorker provides the most up-
to-date compatibility information.

This chapter contains the following topics:

l Software and hardware requirements.............................................................. 326

l Limitations and unsupported features.............................................................. 327
l Transport modes.............................................................................................. 328
l Independent persistent disks cannot be recovered.......................................... 328
l Configuring the VADP proxy host and Hypervisor resource............................. 329
l Creating a VADP User role in vCenter...............................................................331
l Recovering VADP Backups...............................................................................334
l VADP Planning and Best Practices................................................................... 341

VADP Recovery (legacy) 325

VADP Recovery (legacy)

Software and hardware requirements

The software and hardware requirements for VADP include the following.
l One or more VADP proxy systems running any of the following 64-bit operating
systems (English versions only):
n Windows 2008 R2
n Windows 2012
l One or more vCenter servers running any of the following versions:
n vSphere 5.5 with ESX 5.5 and vCenter 5.5
n vSphere 6.0 with ESX 6.0 and vCenter 6.0

Note

NetWorker supports VMware vCenter appliance versions 5.5 and 6.0.

l You must perform the following prerequisites on the NetWorker server/proxy
machine in order to run vSphere version 5.5 and 6.0:
1. Since the registry key for SSL verification is not set by default, add the
following keypath in the registry:

'HKEY_LOCAL_MACHINE/SOFTWARE/Wow6432Node/VMware, Inc./VMware
Virtual Disk Development Kit'

Add a DWORD VerifySSLCertificates and set it to zero

('VerifySSLCertificates=0'). This will disable SSL verification for all VDDK
Hotadd operations.
2. Install .NET framework 3.5.1 or later on the proxy. In Windows 2008 R2, even
though the .NET framework is bundled with the operating system, ensure that
you enable the framework under Server Manager- > features.
3. Install VC++ runtime 9.0 (VC++2008 SP1) on the proxy. The following link
provides more details:
http://www.microsoft.com/en-us/download/details.aspx?id=2092
l Network connectivity must be available between the VADP proxy server and the
vCenter Server managing the ESX server cluster. It also requires connection to
the ESX server system.
l To connect to a Fibre Channel (FC) SAN, the VADP proxy requires a FC host bus
adapter (HBA).
l You must install the NetWorker 9.0.x or later client software on the VADP Proxy
host.
l The NetWorker server requires NetWorker 18.1 software.
l The VADP proxy host must have access to the LUNs required for supported VMs.
Considerations vary depending on the environment, for example, physical and
virtual Compatibility RDMs are not supported and therefore do not require proxy
access. The section VADP proxy access to LUNs on page 347 provides more
information.

326 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

Limitations and unsupported features

The following limitations apply to the VADP solution with NetWorker:
l NetWorker supports the recovery of non-English versions of guest operating
systems for virtual machines. However, if using non-English versions of the
Windows operating system for the vCenter or VADP proxy host, note the
limitations in the sections Limitations to vCenter on non-English versions of
Windows on page 327 and Limitation for VADP proxy host on non-English
versions of Windows on page 327.
l Global directives (both encryption and compression directives) are not supported
by NetWorker for VADP recovery.
l Image-level recovery from a CBT-based incremental backup is not supported.

Limitations to vCenter on non-English versions of Windows

The following limitations apply to non-English versions of the Windows operating
system using vCenter for VADP:
l The following names should always contain only English characters:
n Backup VM display name in the left pane of vCenter
n Backup VM hostname/FQDN
n vCenter Datacenter name
n vCenter Resource pool name
n ESX datastore names containing the VM configuration files and virtual disks.
l You can only restore VMs to the same language OS vCenter that you perform the
backup from. For example, you cannot recover a VM backed up from a Japanese
OS vCenter onto an English OS vCenter.
l You can only perform VADP recovery using the NetWorker User program. A
command line recovery of the entire image will not work for backups from a non-
English vCenter.

Limitation for VADP proxy host on non-English versions of Windows

The following limitation applies to non-English versions of the Windows operating
system for the VADP proxy host:
On the machine where you launch the VADP recovery, install the NetWorker package
in English only without any language packages. You must unselect all the other
language packages explicitly during the NetWorker installation.

Note

Attempting to launch the VADP recovery dialog without following this procedure
results in the overwriting of the local system files, which can lead to machine
corruption.

Limitations and unsupported features 327

VADP Recovery (legacy)

Transport modes
The VADP proxy host supports advanced transport modes for image-level recovery.
You can set the configured network transport mode to the following values during
recovery:
l SAN (Storage Area Network)—Selecting this mode completely offloads the CPU,
memory or I/O load on the virtual infrastructure. The I/O is fully offloaded to the
storage layer where the data is read directly from the SAN or iSCSI LUN.

SAN mode requires a physical proxy with SAN access, and the VMs need to be
hosted on either Fibre Channel or iSCSI-based storage. The corresponding VMFS
volumes must be visible in the Microsoft Windows Disk Management snap-in of
the VADP proxy host.
l Hotadd—In this mode, the I/O happens internally through the ESX I/O stack using
SCSI hot-add technology. This provides better I/O rates than NBD/NBDSSL.
However, selecting this mode places CPU, memory and I/O load on the ESX
hosting the VADP proxy.

Hotadd mode requires a virtual proxy, and the ESX hosting the virtual proxy should
have access to all the datastores where the VMs are hosted So, if the datastores
are SAN/iSCSI/NFS and if the ESX server where the VADP proxy resides is
separate from the ESX server where the VMs are hosted, then:
n In the case of SAN LUNs the ESX hosting the proxy and the ESX hosting the
VMs should be part of the same fabric zones.
n In the case of iSCSI LUNs the ESX hosting the proxy and the ESX hosting the
VMs should be configured for the same iSCSI-based storage targets.
n In the case of NFS datastores, the ESX hosting the proxy and the ESX hosting
the VMs should be configured for the same NFS mount points.
l NBD (Network Block Device): in this mode, the CPU, memory and I/O load gets
directly placed on the ESX hosting the production VMs, because the data has to
move through the same ESX and reach the proxy over the network. NBD mode
can be used either for physical or virtual proxy, and also supports all storage types.
l NBDSSL (Network Block Device with SSL): NBDSSL transport mode is the same
as NBD except that the data transferred over the network is encrypted. Data
transfer in NBDSSL mode can therefore be slower and use more CPU due to the
additional load on the VADP host from SLL encryption/decryption.

You can set multiple transport modes to be used by the VADP proxy host using the
pipe symbol “|” (for example, san|nbd|nbdssl).
By default, the transport mode field in the NetWorker User program is blank. Specify
one transport mode to use for recovery.
More information on configuring transport modes is provided in Configuring the VADP
proxy host and Hypervisor resource. The transport modes are outlined in the table
Table 33 on page 330.

Independent persistent disks cannot be recovered

VADP does not support the recovery of independent persistent disks. If NetWorker
detects these disks, they are skipped and a message is logged that indicates the disks

328 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

were skipped. If using independent persistent disks, you must use traditional
NetWorker recovery.

Configuring the VADP proxy host and Hypervisor resource

A NetWorker client must be created for the VADP proxy host when configuring the
virtual clients for recovery. The VADP proxy NetWorker client will be referred to by
VM clients during VADP recovery operations.
You can create a NetWorker client for the VADP proxy host manually by using the
nsradmin command.

Note

If multiple client instances of the same VADP proxy host exist in the NetWorker
server, ensure that all the instances have the same application information attributes
related to VADP. Manually copy the application information attributes into all the
VADP proxy client instances. Note, however, that when a virtual proxy is used, it
cannot be created by copying the template of other VMs that are being protected.

If vCenter is configured in the environment, there must be a Hypervisor resource for

the vCenter server hosting the VMs that use VADP. You may also need to create a
Hypervisor resource if you cannot use VMware View in the NetWorker VMware
Protection solution, as indicated in the section Enable VMware View in NMC's
Administration window after upgrading by creating a NSR Hypervisor resource on
page 229.
If vCenter is not configured in the environment, there must be a Hypervisor resource
created for each server in the environment.
You must create the corresponding Hypervisor resource in the NetWorker server prior
to starting the VADP recovery.

Creating a Hypervisor resource from the NetWorker server

Procedure
1. Start the NetWorker administration program by running nsradmin. Use the
help command for help, or the visual command to enter full-screen mode.
2. Type the following:

nsradmin> create type:NSR Hypervisor;name:vCenter_FQDN_or_IP

nsradmin> vi
Select type: NSR hypervisor;
name: esx3-vc1.lss.emc.com;
comment: ;
service: [VMware VirtualCenter];
endpoint: "https://esx3-vc1.lss.emc.com/sdk";
username: "ajayads\\nemo"; ======================> vCenter
info
password: *******;
command: nsrvim;
proxy: nemo220-3.lss.emc.com; ============> NW Server

Configuring the VADP proxy host and Hypervisor resource 329

VADP Recovery (legacy)

Creating a NetWorker client for the VADP Proxy host by using the Client
properties windows
Table 33 Application information values

Attribute name Description Default value

VADP_HYPERVIS Specify the hostname of the VC server
OR configured as part of the NSR Hypervisor
This attribute is resource. If there are multiple VC servers
mandatory. configured as part of the NSR hypervisor
resource, specify their hostnames here.
For example:
VADP_HYPERVISOR=any.vc
VADP_HYPERVISOR=another.vc
VADP_TRANSPO Specify the transport mode to transfer Blank. If left blank, the default
RT_MODE data from a VMFS data store to a VADP values are selected in the
proxy server. The following options are order of the description list.
supported: You can specify multiple
modes by inserting a pipe ( | )
l SAN – Virtual disk data is read
symbol between each value as
directly off a shared storage device
shown in the following
that the virtual disk resides on. This
example:
requires VMFS storage on SAN or
VADP_TRANSPORT_MODE=
iSCSI and the storage device has to
san | Hotadd | nbdssl | nbd.
be accessible from both ESX and the
The order in which modes are
VADP proxy.
specified dictate the priority in
l Hotadd – This mode can be used which they are attempted. In
when VADP is used in a virtual proxy. the above example, the san
Because it uses the ESX I/O stack to mode is attempted first; if
move data, Hotadd is more efficient that fails the Hotadd mode is
than the transport mode NBD. attempted, and so on.
l NBDSSL – This mode is the same as
nbd except that the data transferred
over the network is encrypted. The
data transfer in nbdssl mode can be
slower and use more CPU than in the
nbd transport mode.
l NBD – VADP will use an over-the-
network protocol to access the
virtual disk. Data is read from the
storage device by the ESX host and
then sent across an unencrypted
network channel to the VADP proxy.
Please note that this mode does not
provide the offload capabilities of the
san mode (because data is still
transferred from the ESX host across
the network). However, nbd does not
require shared storage and also
enables VADP to be run inside a VM.

330 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

Procedure
1. In the NMC NetWorker Administration Protection window, right-click
Clients, and select New.
The Create Client dialog box displays.
2. Select the General tab.
3. In the Name attribute field, type the name of the proxy.
4. Select the Apps and Modules tab, shown in the following figure.
Figure 165 Apps and Modules tab in NMC

5. In the Application Information field, type the following:

VADP_HYPERVISOR=any.vc
VADP_HYPERVISOR=another.vc
VADP_BACKUPROOT=G:\mnt
VADP_TRANSPORT_MODE=Hotadd

6. Click OK.

Creating a VADP User role in vCenter

The following section provides the steps required to create a VADP User role in the
vCenter server. Although it is possible to run VADP backup/recovery using
Administrator privileges on vCenter, this is not recommended from a security
perspective. It is recommended to create a new role specific to VADP in the vCenter
server and assign it to the user specified in the Hypervisor resource.

Creating a VADP Proxy role

The section Minimum vCenter permissions needed to recover using VADP on page
332 provides more information.
Procedure
1. Log in to the vCenter Server with Administrator privileges using vSphere Client.

Creating a VADP User role in vCenter 331

VADP Recovery (legacy)

2. From the vCenter Server, select View > Administration > Roles.
3. Click Add Role.
4. Name the role VADP User.
5. Assign the required permissions to the VADP User role and click OK.

Assigning the VADP User role to the user specified in the NetWorker
Hypervisor resource
Note

Refer the appropriate VMware Basic System Administration or Datacenter

Administration Guide documentation for steps to assign a role to user.

VMware documentation can be found at http://www.vmware.com/support/pubs/

Procedure
1. Log in to the vCenter Server with Administrator privileges using vSphere Client.
2. Select the vCenter server in the left pane.
3. Click the Permissions tab in the right pane.
4. Right-click inside the right pane and select Add Permission.
5. Add the NetWorker Hypervisor user and assign the VADP User role.
6. Ensure Propagate to Child Objects is enabled and click OK.

Minimum vCenter permissions needed to recover using VADP

It is recommended to create a single VADP User role with the recovery privileges
specified in the following tables. You can then use the associated user for VADP
recovery operations.
The following table provides VADP recovery privileges.

Table 34 VADP recovery privileges

Setting Privileges
Global l Cancel task
l Licenses
l Log Event
l Settings

Resource l Assign virtual machine to resource pool

Datastore l Allocate space

l Browse datastore
l Low level file operations
l Remove file
l Update virtual machine files (only found in
4.1 and later)

332 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

Table 34 VADP recovery privileges (continued)

Setting Privileges
Virtual machine > Inventory l Create new
l Register
l Remove
l Unregister

Virtual machine > Configuration l Add existing disk

l Add new disk
l Add or Remove device
l Advanced
l Change CPU count
l Change Resource
l Disk change Tracking
l Disk Lease
l Extend virtual disk
l Host USB device
l Memory
l Modify device settings
l Raw device
l Reload from path
l Remove disk
l Rename
l Reset guest information
l Settings
l Swapfile placement
l Upgrade virtual machine compatibility

Virtual machine > Interaction l Power Off

l Power On
l Reset

Virtual machine > Provisioning l Allow disk access

l Allow read-only disk access
l Allow virtual machine download

Virtual machine > State l Create snapshot

l Remove snapshot
l Revert to snapshot

Network l Assign network

Minimum vCenter permissions needed to recover using VADP 333

VADP Recovery (legacy)

Table 34 VADP recovery privileges (continued)

Setting Privileges

l Configure

Session l Validate session

Tasks l Create task

l Update task

Recovering VADP Backups

This section covers these topics:
l File based recovery of a VM on page 334
l Image level (single step) recovery of a full VM on page 336

File based recovery of a VM

File-level recovery (FLR) is supported only on VMs that have a Windows operating
system with the NTFS file system. FLR is not supported in the following
configurations:
l Windows 8 and Windows Server 2012 VMs with Resilient File System (ReFS)
l VM operating system containing GPT or dynamic disks
l VM operating system containing uninitialized disks
l VM operating system containing unformatted partitions
l VM operating system containing partitions without drive letters
l VM configuration with Virtual IDE Disk Devices (only SCSI)
l VM configuration with independent disk mode

Performing a file based recovery on the local host

File based recovery on the local host running a VM client requires that the NetWorker
client is installed on the VM client.
To perform a file based recovery on the local host:
Procedure
1. Launch the NetWorker User program on the VM client.
2. Follow the procedure outlined in the NetWorker Administration Guide’s
Recovery chapter. Make sure to specify the restore path using the Recover
Options dialog, illustrated in the following figure.
If you click OK without specifying a restore path in the Recover Options dialog,
a warning message displays, indicating that restoring data to the proxy storage
node from the VM image can result in overwriting system files. To ensure
overwriting of files does not occur, enter a restore path prior to clicking OK.

334 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

Figure 166 Recover Options dialog

Performing a file based recovery using CIFS share

Before you begin
Ensure that the remote access list of the VM client includes either user@server or
user@proxy and that you add the proxies to the DD Boost access list. To add a client
to the DDBoost access list, run the following command from the DDBoost command
line:

ddboost access add clients (- Add clients to a DD Boost access

list)
ddboost access add clients client-list

Procedure
1. Launch the NetWorker User program on the NetWorker server or VADP proxy.
2. Browse the file system for the VM client and select file to recover, as outlined in
the NetWorker Administration Guide’s Recovery chapter.
3. Set the destination directory to the CIFS share of the VM client.
4. Recover the files onto the CIFS share.
5. At the VM client, move the files from the CIFS share to the appropriate
directory.

Performing a file based recovery using directed recovery

File based recovery using directed recovery requires that the NetWorker client is
installed on the VM client.
Procedure
1. Launch the NetWorker User program on the NetWorker server or VM client.

File based recovery of a VM 335

VADP Recovery (legacy)

Note

The user must have the Remote Access All Clients privilege.

2. Select the VM client as the source client.

3. Select the target client as VM-client.
4. Select a destination folder.
5. Follow the procedure in the NetWorker Administration Guide’s Recovery
chapter to select files for recovery and perform the recovery.

Image level (single step) recovery of a full VM

This section describes how to perform an image level recovery (disaster recovery) of
the full VM. There are two methods of recovering a full VM:
l Performing an image level recovery from the NetWorker User program on page
337
l Performing an image level recovery from the command line on page 338

Recommendations and considerations

The following considerations apply when performing an image level recovery of a full
VMware virtual machine:
l For a remote VADP proxy client, image level recovery requires the members of the
VADP proxy client’s administrator group to be part of the remote access list of the
VM clients or the member should have the “Remote access all clients” privilege.
l The user must have VMware privileges to register or create VMs.
l Recovery of the full VM is only supported using save set recovery.
l Only level FULL of FULLVM save sets are supported for VM image recovery.
l The VADP proxy system must be running one of the following:
n Microsoft Windows 2008 R2
n Microsoft Windows 2012
l If any hardware level changes such as a new disk partition, are made to the VM,
you must perform a level full backup before you can perform an image level
recovery of the full VM.
l The VM can recover to the same VMware ESX server or VMware vCenter (VC)
taken at the time of backup or to a different ESX or VC. Recovery to different
resource pools and different datastores are also supported. A different datastore
can be specified for each disk and a configuration datastore can be specified to
restore the configuration files.
l During the recovery of a full VM (FULLVM save set), the recovered VM will start
in forceful powered off state because of a VADP snapshot limitation.
l For non-Windows VMs: If using traditional NetWorker client-based backups along
with VADP image based backups for the same VM client, ensure that the browse
policy for the client-based backups does not exceed the frequency of VADP image
based backups. This practice is recommended because the indices of client-based
backups may have to be removed prior to image-level recovery.

336 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

For example, a Linux client has a schedule of daily level FULL client-based backups
along with monthly VADP image based backups. In this case, it is recommended to
set the browse policy of the client-based backups to a maximum of 1 month.
l If the image level backup of the VM being recovered was performed with the
Encryption directive, the current Datazone pass phrase by default is automatically
used to recover the VM image. If the current Datazone pass phrase was created
after a password-protected backup was performed, you must provide the
password that was in effect when the VM image was originally backed up.

Performing an image level recovery from the NetWorker User program

This procedure is supported on Windows XP and later Windows platforms only.
To perform an image level recovery of a full VM to the VMware ESX server or VMware
vCenter server:
Procedure
1. Launch the NetWorker User program on the NetWorker client or VADP proxy.
2. From the Operation menu, select Save Set Recover.
3. In the Source Client dialog box, select the VM client from where the save set
originated and click OK.
4. In the Save Sets dialog box, select the Save Set name for the full VM backup
client (FULLVM) and select a level FULL backup. Click OK.

Note

Only level full of FULLVM save sets are supported for VM image restore.

5. In the VADP Restore dialog box, type the following information depending on
the type of recovery and then click the Start button.
Restore to VMware vCenter (VC):

l VM DISPLAY NAME- Specify a new VM name to restore the backed up VM.

l vCenter Server - Specify the fully qualified domain name (FQDN) or the IP
address of the VC server.
l Data Center Name - Specify the name of the Data Center to use.
l ESX Server - Specify the fully qualified domain name (FQDN) or the IP
address of the ESX Server on which to perform the restore. By default, the
source ESX server is displayed in this field.
l Config Data Store - Specify the name of the datastore to which the VM
configuration data will be restored.
l Resource Pool Name - Specify the resource pool to use for the restore.
Leave this field empty to use the default pool.
l Transport Mode - Specify the transport mode for recovery (SAN, Hotadd
or NBD).
l Data Store — Specify the name of the datastore for each disk on the VM.
Results
The following figure depicts a VADP Restore dialog box that is set up for a VMware
vCenter restore.

Image level (single step) recovery of a full VM 337

VADP Recovery (legacy)

Figure 167 VMware vCenter restore

Performing an image level recovery from the command line

The following describes how to perform a command line recover of a full VM to the
VMware ESX server or VMware vCenter (VC) server.
Procedure
1. Use the mminfo command to determine the save set ID of the level FULL
FULLVM backup, for example:
mminfo -avot -q "name=FULLVM,level=full"

Note

Only level FULL of FULLVM save sets are supported for VM image recovery.

2. Recover the full VM using the recover command, for example:

recover -S ssid [-d staging-location] -o VADP:host=VC
hostname[:port];VADP:transmode=transport
mode;VADP:datacenter=datacenter name;VADP:resourcepool=resource pool
name; VADP:hostsystem=ESX hostname;VADP:datastore=datastores
where

l ssid is the save set identifier of the FULLVM.

l staging-location is the staging location path to recover the FULLVM image
to the proxy. This value is needed only for a recovery to staging location and
applies only to backups taken before NetWorker 7.6 SP2.
l VC hostname is the VMware VC name that is used to perform the restore.
l port is the port used to log in to the web server of the VC host. If no value is
entered, the default port number is used.
l transport mode is the transport mode to use for recovery. For example,SAN.
l datacenter name is the data center name where the VM is restored to.
l resource pool name is the resource pool that the restored VM is connected
to.
l ESX hostname is the VMware ESX server machine name where the VMware
VM needs to be restored.

338 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

l datastores is the list of datastores that need to be associated with the

configuration and the disks of the VM that is being restored. They are
name / value pairs separated with hash (#) symbols. For example:

VADP:datastore=”config=stor1#disk1=stor2#disk2=stor3”

The following command depicts a command to recover the FULLVM with a

ssid of 413546679. The recovery is directed to the ESX server named
esxDemo1.emc.com. Default values are used for the datacenter, resource
pool, and datastores.

recover.exe -S 413546679 -o
VADP:host=esxDemo1.emc.com;
VADP:transmode=Hotadd

Recover VMs that have a mix of VADP image-level and traditional guest based backups
If your VMs have a mix of both VADP image level backups and traditional guest based
(also known as client based) backups, you may have to use the following recovery
procedure.

Unable to browse guest based backups on non NTFS file systems

Traditional guest based (client based) backups are not browsable in the recovery GUI
for VMs that are running a non NTFS file system and that have a mix of VADP and
guest based backups. This issue does not apply to Windows VMs that are using NTFS.
Additionally, save set recoveries are not affected and can be performed in the usual
way.
To work around the issue, a command line recovery that specifies the backup time
must be performed. Run the following commands from a command line on the VADP
proxy or the VM:
To find the backup time:

mminfo -av -s networker_server -q "client=virtual_client"

To perform the recovery:

recover -t backup_time -s networker_server -c virtual_client

Example
The following VM (host name mars) has a mix of both VADP and traditional guest
based backups. This example shows how to recover a traditional backup save set on
the VM by first locating the time of the backup save set using the mminfo command
and then by using that time with the recover command. The host name of the
NetWorker server in this example is jupiter.

C:\mminfo -av -s jupiter -q "client=mars"

volume type client date time size ssid fl lvl name
kuma-1 Data Domain mars 5/24/2011 10:38:39 PM 281 MB 1658578527 cb
full /root
kuma-1.RO Data Domain mars 5/24/2011 10:38:39 PM 281 MB 1658578527 cb
full /root
kuma-6 Data Domain mars 5/24/2011 10:59:22 PM 5243 MB 1440475890 cb

Image level (single step) recovery of a full VM 339

VADP Recovery (legacy)

full FULLVM
kuma-6.RO Data Domain mars 5/24/2011 10:59:22 PM 5243 MB 1440475890
cb full FULLVM
C:\recover -t "5/24/2011 10:38:39 PM" -s jupiter -c mars

Notice that in the previous example output from the mminfo command, the first two
lines listed are for traditional backup and the last two lines are for a VADP backup,
which is denoted with the save set name, FULLVM. The NetWorker Command
Reference Guide provides more information about using the recover command to mark
(select) files and to perform the recovery.

Image level recovery to a different FARM or vCenter

When recovering to a different server within the same vCenter environment, or when
recovering to a different server within a different vCenter environment, you must
select whether to keep the same UUID, or create a new UUID.

Recovering a VM using SAN or Hotadd transport mode on Windows 2008

When recovering a VM using either the SAN or Hotadd transport mode on a Windows
2008 system, perform the following one-time configuration on the proxy host before
initiating the recovery:
Procedure
1. Open a command prompt on the proxy host.
2. Run the following command:

DISKPART

3. Enter SAN and check for the SAN policy.

4. If the policy indicates offline, enable the policy by entering the following:

SAN POLICY=OnlineALL

Note

After the recovery is successful, SAN POLICY can be changed back to the
default value (SAN POLICY=offline or SAN POLICY=offlineshared).

5. Restart the proxy for the change to take effect.

Results
You can now initiate the VM recovery using SAN or Hotadd mode.

Note

If recovery is initiated from a Windows machine other than the proxy, these steps
need to be performed on the machine where the recovery is initiated.

340 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

VADP Planning and Best Practices

This section covers topics related to best practices when using VADP.

Recommendations and considerations for VADP recovery

Be aware of the following recommendations and considerations before performing
VADP recovery.
l Ensure that VC and ESX/ESXi are updated to the latest released update.
l VADP supports recovery via VMware VirtualCenter or vCenter. The section
Software and hardware requirements on page 326 provides more information on
supported vCenter versions.

Note

Recovery directly to a standalone ESX/ESXi host is not supported. The ESX/ESXi

must be connected to either VirtualCenter or vCenter.
l VADP does not support IPv6. Instructions for disabling IPv6 and using IPv4 are
provided in the section Network and Firewall port requirements on page 343.
l It is recommended to keep the vCenter and VADP proxy as separate machines to
avoid contention of CPU and memory resources.
l The vSphere Client does not need to be installed on the NetWorker server.
l Ensure the path specified in VixDisklib and VixMountAPI config files are enclosed
in double quotes as below:

tempDirectory="C:\Program Files\EMC NetWorker\nsr\plugins\VDDK

\tmp"

These files are stored in the following location by default:

<NetWorker install folder>\nsr\plugins\VDDK\

Note

Double quotes should be specified in the path even though the path is already
present.
l It is recommended to use the VADP proxy host as the storage node. This provides
the optimal configuration for any given transport mode as data transfer occurs
directly from the ESX/ESXi datastore to the storage node.
l If reattaching RDM disks after recovery, make note of all LUNs that are zoned to
the protected VMs.

Selection of physical vs. virtual proxy

NetWorker supports the use of both physical proxy hosts and virtual proxy hosts for
VMware environments. Whether to use a physical or virtual proxy should be
determined based on performance requirements, and available hardware.

VADP Planning and Best Practices 341

VADP Recovery (legacy)

Proxy node sizing and performance considerations

The following proxy node sizing and performance considerations apply when using
physical and virtual proxies.
Note that there are no observed performance differences between physical and virtual
proxies when running on similar hardware.
l The maximum number of concurrent sessions when using a physical proxy is higher
than that of a virtual proxy. The section Recommendations and considerations for
transport modes on page 345 provides more information on concurrent sessions
for specific transport modes.
l Recommendations for a physical proxy is 4 CPU cores with 8GB of RAM.
Recommendations for a virtual proxy is 4 vCPUs and 8GB vRAM per proxy, where
each vCPU is equal to or greater than 2.66 GHz.
l Number of virtual proxies per ESX host depends only on the type of hardware on
which the ESX has been installed.
l For lower-end ESX hosts, it is recommended not to mix I/O load on ESX (with the
virtual proxy and VMs residing on a single ESX), but to have a separate ESX for
the virtual proxy.
l For high-end ESX hosts, it is recommended to have a maximum of 5 virtual proxies
concurrently running on a single ESX host.

Recommendations for Data Domain systems

The following are recommendations for deploying NetWorker and Data Domain
systems to back up the virtualized environment.
l When using DD VTLs, SAN transport mode is required; as a result, the proxy host
cannot be a virtual machine.
l For DD Boost enabled VADP backups:
n The best CPU load and performance is observed with 4 concurrent backups per
device. However, a NetWorker 8.x DD Boost library supports a greater number
of concurrent backups (target sessions).
n Setting a lower number of parallel sessions to a single device does not result in
optimal performance.
n Setting a higher number of parallel sessions to a single device increases the
CPU load without any improvements to performance.
n It is recommended to have at least 400MB to 500MB of RAM for each virtual
machine being backed up if small to medium sized virtual machines are in use
(virtual machines with less than 100GB virtual disks attached). If the largest
virtual machine being backed up has more than 100GB of virtual disks attached,
the RAM can be further increased.
l Better throughput is observed with DD Boost when there is less commonality
between the virtual machines being backed up. As a best practice, it is
recommended that virtual machines related to the same parent virtual machine
template/clone should be part of different backup groups, and these backup
groups should have different start times.
l In the case of both Hotadd and SAN modes, a 20-40% improvement is observed in
the backup throughput for every additional proxy, provided the back-end storage
where the virtual machines reside is not a bottleneck.

342 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

l If using Hotadd mode:

n Refer to the section Recommendations and considerations for transport modes
on page 345 for memory requirements. These requirements may increase
depending on the size of the virtual machine's virtual disks, as described in the
RAM recommendation above.
n Virtual proxy parallelism should not be set to a value greater than 12. This limit
can further be decreased if the virtual machines have more than one disk
attached. More information related to best practices when using Hotadd mode
is provided in the section Recommendations and considerations for transport
modes on page 345.
n In the case of multiple virtual proxies, it is recommended to consolidate all
virtual proxies under dedicated ESX/ESXi host(s) in the environment to
minimize the impact on production VMs during the backup window. These
ESX/ESXi hosts should not be running any other VMs.
n A maximum of 5 virtual proxies per one standalone ESX is recommended.
n A maximum of 3 virtual proxies per ESX is recommended in a DRS cluster for
proxies.

Network and Firewall port requirements

Be aware of the following firewall and network requirements:
l If there is a firewall between the VADP proxy host and the servers that run VMs
that you plan to back up from the VADP proxy host, ensure that bi-directional
TCP/IP connections can be established on port 902 between the VADP proxy host
and the servers.
l If the Virtual Center or vCenter server uses a port other than the default port of
443, specify the port in the endpoint attribute of NSRhypervisor field. Configuring
the VADP proxy host and Hypervisor resource on page 329 provides more
information.
l VADP does not support IPv6. If vCenter is installed in a Windows 2008 system
with IPv6 enabled (IPv6 is enabled by default) and the same system is also used as
the VADP proxy, VADP backups will hang.
Ensure that IPv6 is disabled on the following:
n vCenter
n ESX/ESXi
n VADP-Proxy

Note

ESX/ESXi refers to the actual host system and not the VMs to be backed up.

Disable IPv6 using Network Connections in the Control Panel, then add an IPv4
entry like the following to the hosts file on the system where vCenter is
installed:

<IPv4 address> <vCenter FQDN> <vCenter hostname>

After this entry has been added, run the following command in the VADP proxy
host to verify that the IPv4 address is being resolved:

Network and Firewall port requirements 343

VADP Recovery (legacy)

C:\Users\Administrator>ping <vCenter hostname>

Support for tape drives in a virtual machine

In order to use tape drives (physical and virtual tape drives) in a virtual machine,
specific compatible hardware and VMware ESX/ESXi versions are required, and the
drives must be configured using VMDirectPath.
VMDirectPath allows device drivers in guest operating systems to directly access and
control physical PCI and PCIe devices connected to the ESX host in a hardware pass-
through mode, bypassing the virtualization layer.
The following section requires a working knowledge of VMware vSphere ESX/ESXi
and virtual machine configuration.

VMDirectPath requirements and recommendations

The following requirements and recommendations apply when using VMDirectPath:
l VMDirectPath requires Intel Virtualization Technology for Directed I/O (VT-d) or
AMD IP Virtualization Technology (IOMMU). You may need to enable this option in
the BIOS of the ESX/ESXi system.
l The VM should be Hardware version 7. For example, vmx-07.
l The optimal VMDirectPath PCI/PCIe devices per ESX/ESXi host is 8.
l The optimal VMDirectPath PCI/PCIe devices per VM is 4.

VMDirectPath restrictions
The following restrictions apply during the configuration of VMDirectPath:
l The ESX host must be rebooted after VMDirectPath is enabled.
l The VM must be powered down when VMDirectPath is enabled in order to add the
PCI/PCIe device directly to the VM.
l Using Fibre Channel tape drives in a VM is not supported without VMDirectPath in
production environments due to the lack of SCSI isolation. Tape drives can be
configured and used without VMDirectPath, but the support is limited to non-
production environments.
The VMware knowledge base article http://kb.vmware.com/kb/1010789 provides
information on configuring VMDirectPath.
The following features are not available for a VM configured with VMDirectPath, as
the VMkernel is configured without the respective device under its control when
passed to a VM:
l vMotion
l Storage vMotion
l Fault Tolerance
l Device hot add (CPU and memory)
l Suspend and resume
l VADP Hotadd transport mode (when used as virtual proxy)

Note

If using VMDirectPath in a NetWorker VADP virtual proxy host, then the transport
modes are limited to either NBD or NBDSSL. This is due to a VMware limitation.

The following technical note provides additional information on VMDirectPath:

344 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

http://www.vmware.com/pdf/vsp_4_vmdirectpath_host.pdf

Considerations for VMDirectPath with NetWorker

The following are considerations apply when using VMDirectPath with NetWorker:
l For virtual environments that must run backups to Fibre Channel connected tape
devices where there is a large amount of data in the VM, VMDirectPath can be
used with NetWorker.
l 1 vCPU is sufficient to process 500 GB of data as long as the other VMs are not
sharing the physical core on the underlying ESX/ESXi hardware, and the vCPU
has exclusive access to the single core.
l If other VMs that reside on the same ESX/ESXi are sharing the underlying
hardware (physical CPU), it may be required to add more vCPU and dedicating
underlying hardware by using CPU affinity settings.
l To achieve optimal performance, it is recommended that the guest VM acting as
the DSN has a minimum of 4 GB of memory available with 2 vCPUs allocated.
l If multiple target sessions are needed in each device and 4 or more vCPUs are
assigned to the VM, ensure that there are enough devices available for backup
operations. An insufficient amount of devices can result in less throughput due to
CPU scheduling overhead of the Hypervisor.
l Ensure that the device drivers for the HBA are updated on the guest operating
system.

Recommendations and considerations for transport modes

Following are recommendations for SAN, Hotadd and NBD/NBDSSL transport modes.

SAN transport mode considerations

The following recommendations and considerations apply when one of the VADP
transport modes is set to SAN (VADP_TRANSPORT_MODE=SAN):
l Prior to connecting the VADP proxy host to the SAN fabric, perform the steps in
the section Diskpart utility for SAN and Hotadd transport modes on page 348.
l Memory usage per DD BOOST device should be approximately 500 MB.

Hotadd transport mode considerations

The following recommendations and considerations apply when one of the VADP
transport modes is set to Hotadd (VADP_TRANSPORT_MODE=Hotadd):
l Prior to running VADP backups using the virtual proxy host, perform the steps in
the section Diskpart utility for SAN and Hotadd transport modes on page 348.
l A minimum of 4 vCPUs must be allocated per virtual proxy, with 8GB vRAM per
proxy and each vCPU equal to or greater than 2.66 GHz.
l Memory usage per DD BOOST device should be approximately 300MB.
l The ESX server must be running ESX 3.5 update 4 or later.
l If there are multiple virtual proxies, it is recommended to host all the virtual proxies
in a dedicated ESX/ESXi server. This would keep the virtual proxy resource
consumption of CPU and memory isolated within that ESX/ESXi environment
without impacting the production VMs.

Recommendations and considerations for transport modes 345

VADP Recovery (legacy)

l VMs having IDE virtual disks are not supported for Hotadd mode. Instead, nbd
mode is recommended for these.
l The VM to restore and the VM where the restore is initiated must reside in the
same VMware datacenter.
l The virtual proxy might fail to unmount Hotadd disks. In such cases, you must
manually unmount the Hotadd disks from the virtual proxy. If any of the client VM
disks are still attached to the virtual proxy, perform the following:
1. Right-click the virtual proxy and go to Edit Settings.
2. Select each of the Hotadd disks and choose Remove.

Note

Ensure that you select Remove from virtual machine and not Remove and
delete… when unmounting.

NBD/NBDSSL transport mode considerations

The following recommendations and considerations apply when one of the VADP
transport modes is set to NBD or NBDSSL (for example,
VADP_TRANSPORT_MODE=NBD):
l You can only run a concurrent backup of 20 virtual disks against a given ESX/
ESXi. The limit refers to the maximum number of virtual disks and is per ESX/ESXi
host, irrespective of the number of proxies being used in the environment.
Due to this limitation, it is recommended to apply the following best practices:
n If the ESX is not part of a VMware cluster or is part of a DRS-disabled VMware
cluster, then apply one of the following:
– When using a single proxy to backup a given ESX via NBD/NBDSSL, set the
client parallelism of the VADP proxy Client resource such that the limit of 20
concurrent disk connections per ESX host is not exceeded.
– When using multiple proxies to backup a given ESX via NBD/NBDSSL, then
the client parallelism on each VADP proxy should be calibrated such that the
total concurrent disk connections per ESX host does not exceed 20.
n If ESX is part of a DRS-enabled VMware cluster, then apply one of the
following best practices:
– When using a single proxy to backup via NBD/NBDSSL, set the client
parallelism of the VADP proxy Client resource such that the limit of 20
concurrent disk connections per cluster is not exceeded.
– When using multiple proxies to backup via NBD/NBDSSL, then the client
parallelism on each VADP proxy should be calibrated such that the total
concurrent disk connections per cluster does not exceed 20.

Note

In the following examples, the backup group parallelism would take effect
only if the VADP proxy host client parallelism is set to an equal or higher
number.

One proxy in the environment, all VMs on the same ESX (no cluster)
In the following example, there is a single proxy in the environment and 11 VMs need to
be backed up via NBD/NBDSSL. All 11 VMs are hosted on the same ESX, which is not
part of a cluster, and both of these jobs have to be run at the same time:

346 NetWorker 18.1 VMware Integration Guide

 VADP Recovery (legacy)

l 8 VMs from ESX contains 2 disks disk.

l 3 VMs from same ESX contains 3 disks each.
Use one of the following best practices:
l Set the client parallelism of the proxy to 8.
l Create a single backup group containing all 11 VMs from the given ESX and set the
group parallelism to 8.
Either of the above would ensure that at any given time, the maximum number of disks
being backed up from that ESX will not exceed 20.
Two proxies in the environment, all VMs on the same ESX on DRS-disabled cluster
In the following example, there are two proxies in the environment to back up 11 VMs
via NBD/NBDSSL. All 11 VMs are hosted on the same ESX, which is part of a DRS-
disabled cluster, and both of these jobs have to be run at the same time:
l Proxy1 has been assigned to backup 8 VMs, each VM contains 2 disks.
l Proxy2 has been assigned to backup 3 VMs, each VM contains 3 disks.
Use one of the following best practices:
l Set the client parallelism of Proxy1 and Proxy2 to 5 and 2 respectively.
l Create a single backup group containing all 11 VMs from the given ESX and set the
group parallelism to 8.
Either of the above would ensure that at any given time, the maximum number of disks
being backed up from that ESX will not exceed 20.
Two proxies in the environment, all VMs hosted on DRS-enabled cluster
In the following example, there are two proxies in the environment to back up 11 VMs
via NBD/NBDSSL. All 11 VMs are hosted on one DRS-enabled cluster:
l Proxy1 has been assigned to backup 8 VMs, each VM contains 2 disks.
l Proxy2 has been assigned to backup 3 VMs, each VM contains 3 disks.
Both these jobs have to be run at the same time.
Use one of the following best practices:
l Set the client parallelism of Proxy1 and Proxy2 to 5 and 2 respectively.
l Create a single backup group containing all 11 VMs from the given cluster and set
the group parallelism to 8.
Either of the above would ensure that at any given time, the maximum number of disks
being backed up from that cluster will not exceed 20.

VADP proxy access to LUNs

The following considerations apply when using the following transport modes to
access LUNs.

SAN transport mode

For SAN mode, the VADP proxy requires read access to the SAN LUNs hosting the
VMs.
For image recovery via SAN mode, ensure that the VADP proxy has read-write access
to the SAN LUNs hosting the VMs. To ensure read-write access, add the VADP proxy
to the same fabric zones to which the ESX server system belongs.

VADP proxy access to LUNs 347

VADP Recovery (legacy)

Hotadd transport mode

For Hotadd mode, the ESX server (where the VADP proxy VM resides) must have
access to the datastores of the VMs. For example, if the datastores are from SAN
LUNs and the ESX server where the VADP proxy resides is separate from the ESX
server where the VMs are located, then the ESX hosting the proxy should be part of
the same fabric zones to which the ESX hosting the VMs belongs.

NBD/NBDSSL transport modes

For nbd/nbdssl, no zoning is required since access to the datastore is always by way
of LAN. Only network connectivity to ESX/ESXi is required for access to the
datastore.

Diskpart utility for SAN and Hotadd transport modes

When an RDM NTFS volume is being used for any of the VMs on the VADP proxy
host, Windows will automatically attempt to mount the volume and assign drive letters
to VM disks. This may lead to data corruption on the VMs.
To prevent Windows from automatically assigning drive letters to the RDM NTFS,
perform the following steps.

Note

Steps 1 and 2 are only applicable in the case of SAN transport mode where SAN fabric
zoning is already in place such that the VADP proxy host is already displaying the SAN
LUNs in Windows disk management. If this does not apply, skip to Step 3.

1. Shut down the Windows proxy.

2. Disconnect the Windows proxy from the SAN or mask all the LUNs containing
VMFS volumes or RDM for VMs.
3. Start the proxy and log into an account with administrator privileges.
4. Open a command prompt and run the diskpart utility by entering the following:
diskpart
The diskpart utility starts and prints its own command prompt.
5. Disable automatic drive letter assignment to newly discovered volumes by entering
the following in the diskpart command prompt:
automount disable
6. Clean out entries of previously mounted volumes in the registry by entering the
following in the diskpart command prompt:
automount scrub

348 NetWorker 18.1 VMware Integration Guide

APPENDIX A
NetWorker VMware Protection in VMware
Cloud on Amazon Web Services

This appendix includes the following topics:

l Introduction to NetWorker VMware Protection in VMware Cloud on AWS...... 350

l Prerequisites....................................................................................................350
l Deploy the vProxy OVA on a vCenter server in VMware Cloud on AWS...........352
l NetWorker VMware Protection for VMware Cloud on AWS best practices..... 354
l Unsupported NetWorker operations................................................................ 355

NetWorker VMware Protection in VMware Cloud on Amazon Web Services 349

NetWorker VMware Protection in VMware Cloud on Amazon Web Services

Introduction to NetWorker VMware Protection in VMware

Cloud on AWS
NetWorker 18.1 supports NetWorker VMware Protection in VMware Cloud on Amazon
Web Services (AWS).
Using NetWorker to protect virtual machines running in VMware Cloud on AWS is
similar to how you protect the virtual machines in an on-premises datacenter. This
appendix provides information on network configuration prerequisites, VMware Cloud
on AWS best practices for NetWorker, and NetWorker operations that are currently
unsupported for VMware Cloud on AWS
A NetWorker with CloudBoost environment can be useful for storing backups in
Amazon S3 cloud object storage, including short term backups for operational
recovery and long term retention backups for compliance. This capability is currently
available with both in-guest filesystem agents as well as a broad range of application
modules for NetWorker. NetWorker vProxy backups are currently not supported with
CloudBoost, however cloning of vProxy backups to cloud object storage is supported
via the CloudBoost appliance.
Additional information on NetWorker VMware Protection in VMware Cloud on AWS,
including setup and configuration instructions, is provided in the whitepaper on
https://support.emc.com/products/1095_NetWorker/Documentation/.

Prerequisites
Domain Name System (DNS) resolution is critical for NetWorker deployment and
configuration. All infrastructure components should be resolvable through a fully
qualified domain name (FQDN). This is especially important for the NetWorker Server,
NetWorker vProxy, Data Domain appliance, and CloudBoost appliance. Resolvable
means that components are accessible through both forward (A) and reverse (PTR)
look-ups.
Review the following prerequisites prior to configuring NetWorker in a VMware Cloud
on AWS. Also, ensure that you plan your firewall according to these prerequisites.
VMware Cloud on AWS web portal console
In the VMware Cloud on AWS web portal console, note the following requirements:
l If using NSX-T, configure the DNS to resolve to the internal IP address of the
vCenter server. Navigate to SDDC Management > Settings > vCenter FQDN and
select the Private vCenter IP address so that you can directly access the
management network over the built-in firewall. Additionally, ensure that you open
TCP port 443 of the vCenter server in both the management gateway and the
compute gateway.
l By default, there is no external access to the vCenter Server system in your SDDC
(Software Defined Data Center). You can open access to your vCenter Server
system by configuring a firewall rule. Set the firewall rule in the compute gateway
of VMware Cloud on AWS to enable communication to the vCenter public IP
address from the desired logical network of your SDDC. The NetWorker server will
not allow you to add the vCenter Server if this firewall rule is not configured in the
SDDC.
l The default compute gateway firewall rules prevent all virtual machine traffic from
reaching the internet. To allow your NetWorker Server virtual machine to connect
to the internet, you need to create a compute gateway firewall rule to allow

350 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection in VMware Cloud on Amazon Web Services

outbound traffic on the logical network that your NetWorker Server virtual
machine is connected to.
l Configure DNS to allow machines in your SDDC to resolve fully-qualified domain
names (FQDNs) to IP addresses belonging to the internet. The NetWorker Server
will not allow you to add the vCenter Server using the server's public FQDN or IP
address if the DNS server is not configured in your SDDC.
l It is recommended that you deploy the Data Domain system as a virtual appliance
in the Amazon VPC (Virtual Private Cloud) of your choice. During the SDDC
creation, ensure that you connect your SDDC to an AWS account, and select a
VPC and subnet within that account.
l The Data Domain system running in your Amazon VPC must be connected to your
VMware SDDC by using the VMware Cloud Elastic Network Interfaces (ENIs),
allowing your SDDC and services in the AWS VPC and subnet in your AWS
account to communicate without requiring the routing of traffic through the
internet gateway. The same ENI channel is recommended for access to Data
Domain systems (for the vProxy solution) and access to cloud object storage (for
the CloudBoost solution). Detailed steps on configuring ENI are provided by
VMware at https://vmc.vmware.com/console/aws-link.
l Ensure that you configure the inbound and outbound firewall rules of your
compute gateway for Data Domain connectivity if DDVE is running in your Amazon
VPC.
Amazon AWS web portal
In the AWS web portal, note the following requirements:
l Configure the inbound and outbound firewall rules of your Amazon VPC security
group to provide connectivity between the VMware SDDC compute gateway and
Data Domain connectivity if Data Domain is running in your Amazon VPC.
l If cloning from one Data Domain system to another, ensure that you configure the
inbound rule for the security group in AWS to allow all traffic from the respective
private IPs of Data Domain Virtual Editions running in your Amazon VPC.
l If you have more than one Data Domain running in AWS to perform cloning, then
ensure that both Data Domain systems can ping each other using the FQDNs.
vCenter server inventory
In the vCenter Server inventory of your SDDC, note the following requirements:
l An internal DNS name lookup server must be running inside the vCenter inventory.
This will be referenced by all the workloads running in the VMware SDDC.
l The internal DNS server must have Forwarders enabled to access the internet.
This is required in order to resolve the vCenter Server's public FQDN

Prerequisites 351
NetWorker VMware Protection in VMware Cloud on Amazon Web Services

Figure 168 Enable internet access for Forwarders

Deploy the vProxy OVA on a vCenter server in VMware

Cloud on AWS
Perform the following steps to deploy the OVA for the vProxy host from a vCenter
server by using the HTML5 vSphere Web Client.
Before you begin
Review the Pre-requisites section.
Procedure
1. Log in to the HTML5 vSphere Web Client with the cloudadmin account
credentials.
2. From the top-left of the window, select Menu, and then select Hosts and
Clusters from the drop-down.
3. In the left inventory pane, expand the vCenter, and then expand the compute
resource pool inside your SDDC cluster.
4. Right-click the resource pool where you want to deploy the OVA and select
Deploy OVF template.
5. On the Select an OVF template window, type a URL path to the OVA package,
or click Choose Files and navigate to the OVA package location, and then click
Next.
6. On the Select a name and folder window, specify a name for the virtual
appliance, and the inventory location (for example a virtual machine folder).
Click Next.
7. On the Select a compute resource window, select the vApp or resource pool
where you want to deploy the OVA, and then click Next.

352 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection in VMware Cloud on Amazon Web Services

8. On the Review details window, review the product details such as the product
name, version, vendor, publisher, and download size, and then click Next.
9. On the License agreements window, review and accept the EULA, and then
click Next.
10. On the Select storage window, select the disk format and the destination
datastore where the virtual appliance files will be stored, and then click Next.
It is recommended that you select Thick Provision Lazy Zeroed to ensure that
amount of storage space allocated to the virtual appliance is available.
11. On the Select networks window, select the Destination Network. Provide the
IP address in the text box and click Next.
12. On the Customize template window, expand Networking properties, and then
specify the following attributes:
a. In the Network IP address field, specify the IP address for the vProxy
appliance.
b. In the Default gateway field, specify the IP address of the gateway host.
c. In the Network Netmask/Prefix field, specify the netmask for an IPv4
Network IP address. vProxy backups do not support the use of IPv6
Network IP addresses.
d. In the DNS field, specify the IP address of the DNS servers, separated by
commas.
e. In the FQDN field, specify the fully qualified domain name of the vProxy
appliance.
13. Expand Timezone settings, and then perform the following tasks:
a. in the Timezone setting field, select the time zone.
b. SSH into the vProxy appliance using root credentials and run the following
command: /usr/bin/timedatectl set-timezone new-timezone.

Note

To set a time zone outside of the list supported by the vProxy appliance, you
need to change the time zone manually.

14. Expand Password settings, and then perform the following tasks:
a. In the Root password field, specify a password for the root account or leave
the field blank to use the default password. The default password is
changeme.

b. In the Admin password field, specify a password for the admin account or
leave the field blank to use the default password. The default password is
a3dp@m8n.
15. Click Next.
The Ready to Complete window displays.
16. On the Ready to Complete window, review the deployment configuration
details, and then click Finish.

Deploy the vProxy OVA on a vCenter server in VMware Cloud on AWS 353
NetWorker VMware Protection in VMware Cloud on Amazon Web Services

Results
The Deploying template task appears in the vCenter and provides status information
about the deployment.

NetWorker VMware Protection for VMware Cloud on AWS

best practices
Observe the following best practices when using NetWorker to protect virtual
machines running in VMware Cloud on AWS:
l When deploying or configuring the NetWorker Server or vProxy, ensure that you
specify the DNS server IP that points to the internal DNS server running in the
vCenter inventory.
l Ensure that both forward and reverse lookup entries in the internal DNS server are
in place for all of the required components, such as the NetWorker Server,
NetWorker vProxy appliance, Data Domain Virtual Edition (DDVE), and
CloudBoost appliance.
l When adding the vCenter Server to NMC's VMware View, ensure that you select
the Deployed in Cloud checkbox. Note that this setting is required for any
vCenter Servers running in VMware Cloud on AWS, If you do not select this
option, then some NetWorker operations will fail in the VMware Cloud on AWS.
Figure 169 Add a vCenter Server to VMware View with Deployed in Cloud enabled

l Add the vCenter Server to the NetWorker Server using either the public FQDN of
the vCenter Server or the public IP address of the vCenter Server. It is
recommended to use the FQDN.
l When adding the vCenter Server to the NetWorker Server, specify the login
credentials for the cloudadmin user
l When configuring the vProxy in the NetWorker Server, set the Maximum NBD
sessions for the vProxy to zero. VMware Cloud on AWS does not support NBD
transport mode.

354 NetWorker 18.1 VMware Integration Guide

 NetWorker VMware Protection in VMware Cloud on Amazon Web Services

Figure 170 NSR VMware Proxy Properties

Unsupported NetWorker operations

NetWorker VMware Protection in VMware Cloud on AWS does not currently support
the following operations:
l File-level restore from an image-level backup.
l Instant access recovery of an image-level backup.
l Emergency restore (image-level restore directly to an ESXi host, bypassing the
vCenter).
l Image-level backups and restores using NBD or NBDSSL transport mode.
l vProxy appliance configured with dual stack or IPv6 only is not supported.
l Application-consistent data protection for MS-SQL with the vProxy appliance.
l If the datacenter is placed inside a folder in the SDDC, image backup and restore is
not supported

Unsupported NetWorker operations 355

NetWorker VMware Protection in VMware Cloud on Amazon Web Services

356 NetWorker 18.1 VMware Integration Guide

APPENDIX B
Regular expressions for NetWorker vProxy
dynamic policies rule definitions

This appendix includes the following topic:

l Regular expression syntax accepted by dynamic policy rule definition............. 358

Regular expressions for NetWorker vProxy dynamic policies rule definitions 357
Regular expressions for NetWorker vProxy dynamic policies rule definitions

Regular expression syntax accepted by dynamic policy rule

definition
Rule definitions for NetWorker vProxy policies with dynamic association enabled can
contain regular expressions.
The following tables list the acceptable rules, syntax, and grammar to use when
writing such regular expressions.
Types of single-character expressions Examples
Any character, possibly including newline .
(s=true)

character class [xyz]

negated character class [^xyz]

Perl character class \d

negated Perl character class \D

ASCII character class [[:alpha:]]

negated ASCII character class [[:^alpha:]]

Unicode character class (one-letter name) \pN

Unicode character class \p{Greek}

negated Unicode character class (one-letter \PN

name)

negated Unicode character class \P{Greek}

Composites
xy x followed by y

x|y x or y (prefer x)

Repetitions
x* zero or more x, prefer more

x+ one or more x, prefer more

x? zero or one x, prefer one

x{n,m} n or n+1 or ... or m x, prefer more

x{n,} n or more x, prefer more

x{n} exactly n x

x*? zero or more x, prefer fewer

x+? one or more x, prefer fewer

x?? zero or one x, prefer zero

x{n,m}? n or n+1 or ... or m x, prefer fewer

x{n,}? n or more x, prefer fewer

358 NetWorker 18.1 VMware Integration Guide

 Regular expressions for NetWorker vProxy dynamic policies rule definitions

Repetitions
x{n}? exactly n x

Note

The counting forms x{n,m}, x{n,}, and x{n} reject forms that create a minimum or
maximum repetition count above 1000. Unlimited repetitions are not subject to this
restriction.

Grouping
(re) numbered capturing group (submatch)

(?P<name>re) named & numbered capturing group

(submatch)

(?:re) non-capturing group

(?flags) set flags within current group; non-capturing

(?flags:re) set flags during re; non-capturing

Flags
i case-insensitive (default false)

m multi-line mode: ^ and $ match begin/end line

in addition to begin/end text (default false)

s let . match \n (default false)

U ungreedy: swap meaning of x* and x*? , x+

and x+? , etc (default false)

Flag syntax is xyz (set) or -xyz (clear) or xy-z (set xy , clear z ).

Empty strings
^ at beginning of text or line ( m =true)

$ at end of text (like \z not \Z ) or line ( m

=true)

\A at beginning of text

\b at ASCII word boundary ( \w on one side and

\W , \A , or \z on the other)

\B not at ASCII word boundary

\z at end of text

Escape sequences
\a bell ( ≡ \007 )

\f form feed ( ≡ \014 )

\t horizontal tab ( ≡ \011 )

\n newline ( ≡ \012 )

\r carriage return ( ≡ \015 )

Regular expression syntax accepted by dynamic policy rule definition 359

Regular expressions for NetWorker vProxy dynamic policies rule definitions

Escape sequences
\v vertical tab character ( ≡ \013 )

\* literal * , for any punctuation character *

\123 octal character code (up to three digits)

\x7F hex character code (exactly two digits)

\x{10FFFF} hex character code

\C match a single byte even in UTF-8 mode

\Q...\E literal text ... even if ... has punctuation

Character class elements

x single character

A-Z character range (inclusive)

\d Perl character class

[:foo:] ASCII character class foo

\p{Foo} Unicode character class Foo

\pF Unicode character class F (one-letter name)

Named character classes as character

class elements
[\d] digits ( ≡ \d )

[^\d] not digits ( ≡ \D )

[\D] not digits ( ≡ \D )

[^\D] not not digits ( ≡ \d )

[[:name:]] named ASCII class inside character class ( ≡

[:name:] )

[^[:name:]] named ASCII class inside negated character

class ( ≡ [:^name:] )

[\p{Name}] named Unicode property inside character

class ( ≡ \p{Name} )

[^\p{Name}] named Unicode property inside negated

character class ( ≡ \P{Name} )

Perl character classes (all ASCII-only)

\d digits ( ≡ [0-9] )

\D not digits ( ≡ [^0-9] )

\s whitespace ( ≡ [\t\n\f\r ] )

\S not whitespace ( ≡ [^\t\n\f\r ] )

\w word characters ( ≡ [0-9A-Za-z_] )

\W not word characters ( ≡ [^0-9A-Za-z_] )

360 NetWorker 18.1 VMware Integration Guide

 Regular expressions for NetWorker vProxy dynamic policies rule definitions

ASCII character classes

[[:alnum:]] alphanumeric ( ≡ [0-9A-Za-z] )

[[:alpha:]] alphabetic ( ≡ [A-Za-z] )

[[:ascii:]] ASCII ( ≡ [\x00-\x7F] )

[[:blank:]] blank ( ≡ [\t ] )

[[:cntrl:]] control ( ≡ [\x00-\x1F\x7F] )

[[:digit:]] digits ( ≡ [0-9] )

[[:graph:]] graphical ( ≡ [!-~] ≡ [A-Za-z0-9!"#$%&'()*+,

\-./:;<=>?@[\\\]^_`{|}~] )

[[:lower:]] lower case ( ≡ [a-z] )

[[:print:]] printable ( ≡ [ -~] ≡ [ [:graph:]] )

[[:punct:]] punctuation ( ≡ [!-/:-@[-`{-~] )

[[:space:]] whitespace ( ≡ [\t\n\v\f\r ] )

[[:upper:]] upper case ( ≡ [A-Z] )

[[:word:]] word characters ( ≡ [0-9A-Za-z_] )

[[:xdigit:]] hex digit ( ≡ [0-9A-Fa-f] )

Unicode character class names--

general category
C other

Cc control

Cf format

Co private use

Cs surrogate

L letter

Ll lowercase letter

Lm modifier letter

Lo other letter

Lt titlecase letter

Lu uppercase letter

M mark

Mc spacing mark

Me enclosing mark

Mn non-spacing mark

N number

Nd decimal number

Nl letter number

Regular expression syntax accepted by dynamic policy rule definition 361

Regular expressions for NetWorker vProxy dynamic policies rule definitions

Unicode character class names--

general category
No other number

P punctuation

Pc connector punctuation

Pd dash punctuation

Pe close punctuation

Pf final punctuation

Pi initial punctuation

Po other punctuation

Ps open punctuation

S symbol

Sc currency symbol

Sk modifier symbol

Sm math symbol

So other symbol

Z separator

Zl line separator

Zp paragraph separator

Zs space separator

Vim character classes

\d digits ( ≡ [0-9] ) VIM

\D not \d VIM

\w word character VIM

\W not \w VIM

362 NetWorker 18.1 VMware Integration Guide

GLOSSARY

This glossary contains terms related to disk storage subsystems. Many of these terms
are used in this manual.

backup 1. Duplicate of database or application data, or an entire computer system, stored

separately from the original, which can be used to recover the original if it is lost or
damaged.
2. Operation that saves data to a volume for use as a backup.

Backup proxy The system designated as the off-host backup system. This is a host with NetWorker
client package installed and the VADP software.

changed block tracking A VMkernel feature that keeps track of the storage blocks of virtual machines as they
change over time. The VMkernel keeps track of block changes on virtual machines,
which enhances the backup process for applications that have been developed to take
advantage of VMware’s vStorage APIs.

checkpoint A system-wide backup, taken only after 24 hours (and at the time of the checkpoint
after that first 24 hours have elapsed), that is initiated within the vSphere Web Client
and captures a point in time snapshot of the EMC Backup and Recovery appliance for
disaster recovery purposes.

client Host on a network, such as a computer, workstation, or application server whose data
can be backed up and restored with the backup server software.

client file index Database maintained by the NetWorker server that tracks every database object, file,
or file system backed up. The NetWorker server maintains a single index file for each
client computer. The tracking information is purged from the index after the browse
time of each backup expires.

Console server See NetWorker Management Console (NMC).

datastore A virtual representation of a combination of underlying physical storage resources in the

datacenter. A datastore is the storage location (for example, a physical disk, a RAID, or
a SAN) for virtual machine files.

NetWorker 18.1 VMware Integration Guide 363

Glossary

EMC Backup and The EMC Backup and Recovery appliance (or VMware Backup Appliance) is an
Recovery Appliance appliance that, when deployed, enables VMware backup and clone policy creation in
NMC, and enables the EMC Backup and Recovery plug-in in the vSphere Web Client to
assign VMs to those policies.

EMC Data Protection A browser that allows for file-level restores, where specific folders and files are
Restore Client restored to the original virtual machine on Windows and Linux virtual machines.

file index See client file index.

file-level restore (FLR) Allows local administrators of protected virtual machines to browse and mount backups
for the local machine. From these mounted backups, the administrator can then restore
individual files. FLR is accomplished using the EMC Data Protection Restore Client. See
“Using File Level Restore” on page 63 for additional information on FLR.

Guest OS An operating system that runs on a virtual machine.

hotadd A transport mode where the backup related I/O happens internally through the ESX I/O
stack using SCSI hot-add technology. This provides better backup I/O rates than NBD/
NBDSSL.

image level backup and Used in the case of a disaster recovery.

recovery

inactivity timeout Time in minutes to wait before a client is considered to be unavailable for backup.

JAR (Java Archive) A file that contains compressed components needed for a Java applet or application.

label Electronic header on a volume used for identification by a backup application.

364 NetWorker 18.1 VMware Integration Guide

 Glossary

managed application Program that can be monitored or administered, or both from the Console server.

media database Database that contains indexed entries of storage volume location and the life cycle
status of all data and volumes managed by the NetWorker server.

metadata VSS-defined information that is passed from the writer to the requestor. Metadata
includes the writer name, a list of VSS components to back up, a list of components to
exclude from the backup, and the methods to use for recovery. See writer and See VSS
component.

NBD A transport mode over LAN that is typically slower than hotadd mode. In NBD mode,
the CPU, memory and I/O load gets directly placed on the ESX hosting the production
VMs, since the backup data has to move through the same ESX and reach the proxy
over the network. NBD mode can be used either for physical or virtual proxy, and also
supports all storage types.

NBDSSL A transport mode that is the same as NBD except that the data transferred over the
network is encrypted. Data transfer in NBDSSL mode can therefore be slower and use
more CPU due to the additional load on the VADP host from SLL encryption/
decryption.

NetWorker administrator NetWorker server user who may add, change, or delete NetWorker server users.

NetWorker client See client.

NetWorker Management Software program that is used to manage NetWorker servers and clients. The NMC
Console (NMC) server also provides reporting and monitoring capabilities for all NetWorker processes.

NetWorker server Computer on a network that runs the NetWorker server software, contains the online
indexes, and provides backup and restore services to the clients and storage nodes on
the same network.

NetWorker storage node See storage node.

online indexes Databases located on the NetWorker server that contain all the information pertaining
to the client backups (client file index) and backup volumes (media index).

recover To restore data files from backup storage to a client and apply transaction (redo) logs
to the data to make it consistent with a given point-in-time.

NetWorker 18.1 VMware Integration Guide 365

Glossary

SAN (storage area A transport mode that, when used, completely offloads the backup related CPU,
network) memory or I/O load on the virtual infrastructure. The backup I/O is fully offloaded to
the storage layer where the data is read directly from the SAN or iSCSI LUN. SAN
mode requires a physical proxy.

save NetWorker command that backs up client files to backup media volumes and makes
data entries in the online index.

save set 1. Group of tiles or a file system copied to storage media by a backup or snapshot
rollover operation.
2. NetWorker media database record for a specific backup or rollover.

single step backup and See image level backup and recovery.
recovery

storage node Computer that manages physically attached storage devices or libraries, whose backup
operations are administered from the controlling NetWorker server. Typically a
“remote” storage node that resides on a host other than the NetWorker server.

update enabler Code that updates software from a previous release. It expires after a fixed period of
time.

VADP An acronym for vStorage APIs for Data Protection. VADP enables backup software to
perform centralized virtual machine backups without the disruption and overhead of
running backup tasks from inside each virtual machineVADP supersedes the VCB
framework for VMware backups.

vCenter An infrastructure management tool that provides a central point for configuring,
provisioning, and managing virtualized IT environments, and is part of the VMware
Virtual Infrastructure package.

Virtual machine Software that creates a virtualized environment between the computer platform and its
operating system, so that the end user can install and operate software on an abstract
machine.

VM An acronym for virtual machine.

VMDK Virtual Machine Disk (VMDK) is a file or set of files that appears as a physical disk drive
to a guest operating system. These files can be on the host machine or on a remote file
system. These files are commonly called VMDK files because of the .vmdk extension
that VMware adds to these files.

VMware Backup The VMware Backup Appliance (or EMC Backup and Recovery appliance) is an
Appliance appliance that, when deployed, enables VMware backup and clone policy creation in
NMC, and enables the EMC Backup and Recovery plug-in in the vSphere Web Client to
assign VMs to those policies.

366 NetWorker 18.1 VMware Integration Guide

 Glossary

VMware Tools Installed inside each virtual machine, VMware Tools enhance virtual machine
performance and add additional backup-related functionality.

VSS (Volume Shadow Microsoft technology that creates a point-in-time snapshot of a disk volume.
Copy Service) NetWorker software backs up data from the snapshot. This allows applications to
continue to write data during the backup operation, and ensures that open files are not
omitted.

VSS component A subordinate unit of a writer. See writer.

writer Database, system service, or application code that works with VSS to provide metadata
about what to back up and how to handle VSS components and applications during
backup and restore. See VSS (Volume Shadow Copy Service).

NetWorker 18.1 VMware Integration Guide 367

Glossary

368 NetWorker 18.1 VMware Integration Guide