0% found this document useful (0 votes)
333 views1 page

Metric: Hex Nut Style 2 Class 9

This document provides specifications for metric hex nuts in Style 2, including nominal sizes from M5 to M36. It lists the maximum and minimum dimensions for width across flats, width across corners, and thickness for each size. Style 2 nuts are approximately 10% thicker than Style 1 nuts of the same diameter. Class 9 nuts are intended for use with bolts of property classes 4.6 to 9.8 and are made of steel meeting specified chemical composition and hardness requirements. Proof load standards are provided for each size range. Plating information is referenced in Appendix A.

Uploaded by

Ratendra kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
333 views1 page

Metric: Hex Nut Style 2 Class 9

This document provides specifications for metric hex nuts in Style 2, including nominal sizes from M5 to M36. It lists the maximum and minimum dimensions for width across flats, width across corners, and thickness for each size. Style 2 nuts are approximately 10% thicker than Style 1 nuts of the same diameter. Class 9 nuts are intended for use with bolts of property classes 4.6 to 9.8 and are made of steel meeting specified chemical composition and hardness requirements. Proof load standards are provided for each size range. Plating information is referenced in Appendix A.

Uploaded by

Ratendra kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Hex Nut Style 2

Nuts METRIC Class 9

F H

METRIC - HEX NUTS , STYLE 2 ISO 4033

F G H

Nominal Size Thread Pitch Width Across Flats Width Across Corners Thickness

Max Min Min Max Min


M5 0.8 8 7.78 8.79 5.1 4.8
M6 1 10 9.78 11.05 5.7 5.4
M8 1.25 13 12.73 14.38 7.5 7.14
M10 1.5 16 15.73 17.77 9.3 8.94
M12 1.75 18 17.73 20.03 12 11.57
M14 2 21 20.67 23.35 14.1 13.4
M16 2 24 23.67 26.75 16.4 15.7
M20 2.5 30 29.16 32.95 20.3 19
M24 3 36 35 39.55 23.9 22.6
M30 3.5 46 45 50.85 28.6 27.3
M36 4 55 53.8 60.79 34.7 33.1

A six-sided internally threaded, non-heat treated fastener with a metric thread pitch which, as a Style 2 nut, is approximately 10% thicker
Description than a Style 1 nut of the same nominal diameter. Nuts M16 and smaller are chamfered on the top and the bearing surface. Nuts M18
and larger may be either double chamfered, or have a washer face on one side and a chamfered surface on the opposite side.
Applications/
Class 9 nuts are intended for use with screws and bolts of property classes 4.6, 4.8, 5.8, 8.8 or 9.8.
Advantages
Class 9 nuts shall be made of a steel which conforms to the following chemical composition-- Carbon: 0.58% maximum;
Material
Manganese: 0.25% minimum; Phosphorus: 0.060% maximum; Sulfur: 0.150% maximum.
Diameters M1.6 through M4: Rockwell B85 - C30 (Vickers HV 170 - 302)
Hardness Diameters M5 through M39: Rockwell B89 - C30 (Vickers HV 188 - 302)
Diameters M1.6 through M4: 900 N/mm2
Diameters M5 through M7: 915 N/mm2
Proof Load Diameters M8 through M10: 940 N/mm2
Diameters M12 through M16: 950 N/mm2
Diameters M18 through M39: 920 N/mm2
Plating See Appendix-A for plating information

You might also like