Operation Manual

Rev: 2.0.0
 CONTENTS
Chapter 1. Introduction ..................................................................................................................... 1
Chapter 2. Preparing for configuration ............................................................................................. 1
2.1 Equipment Required ........................................................................................................... 1
2.2 Installing Agile Suite ........................................................................................................... 1
Chapter 3. Generating configuration files ......................................................................................... 2
3.1 General Config .................................................................................................................... 2
3.2 Specific Config ................................................................................................................... 4
3.3 Logo Config and Favicon Config ....................................................................................... 6
Chapter 4. Upgrading the devices ..................................................................................................... 7
4.1 Topology ............................................................................................................................. 7
4.2 Upgrading process............................................................................................................... 7
Chapter 5. FAQ ................................................................................................................................. 9
Chapter 1. Introduction

Agile Config is a function that simplifies WISP customization process, it can be used to customize
the default configurations of devices in batches. Flexible settings include logo, WAN connection
type, SSID, password, time zone, language, and so on.
Agile Config consists of four major modules——General Config, Specific Config, Logo Config
and Favicon Config. General Config is used to upgrading the common configurations of devices
with same HW&SW version to the format required by WISP. Specific Config is used to set specific
configurations for each device according to its MAC address. Logo Config and Favicon Config are
used to change the ISP logo and Favicon as you want.
You can learn how to use Agile Config function from this file, and feel freely to contact us if you
have any problems.

Chapter 2. Preparing for configuration

2.1 Equipment Required

 Hardware required: one PC, one switch and one router (or device) which supports Agile Config
function.

 Supported operating systems: Windows 7/ Windows 10 (NET Framework 3.5 or later needed).

 Software required: Excel 2007 or later; Agile Config 2.0 Suite.

2.2 Installing Agile Suite

You will receive Agile suite which contains the items below:

Figure 2-1

 Note: The password of this two installers is “Tplinkonly1”.

1
 Figure 2-2

2) Install ISP Generator Setup.exe according to the guidelines, and you will get the MAC.bin gen.

Figure 2-3

Chapter 3. Generating configuration files

3.1 General Config

General Config is available for multiple devices with the same software, for General Config, you
need a standard prototype.

1. Plug the PC to the LAN port of the standard prototype via an Ethernet cable, and login the web
management page.

2
 Note:
a) The IP address of your PC should be obtained automatically here.

b) Please find the login informations from the label on the bottom of the standard prototype.

2. Set the configuration items as WISP required and save them. All the items you can find on the
Web UI are supported to be changed as you want.

Figure 3-1

3. You can obtain the configuration file in the Backup & Restore page by clicking “Backup”.
The configuration file will be downloaded right away by the browser, and you can find it in
the download path.

3
 Figure 3-2

 Note:
a) The exported configuration file is one “xxxxx.bin” file based on model name, usually it is
named as “model+version.bin”.
b) If the backup file is “conf.bin”, that means your device does not support Agile config
function.

3.2 Specific Config

Specific Config only supports changing several parameters now, including Network Name (SSID)
and Wireless password, the username and password of Web management interface, username and
password of PPPoE connection, IP address, subnet mask and gateway address of static IP connection.

Here is a typical example: A WISP bought 100 pcs of our products, and they want to set PPPoE as
connection type. Each device have different PPPoE username and password, we can set and record
them as default configuration via the tool.

1. Run ISP generater.exe as administrator.

4
 Figure 3-3

2. If you want to obtain random parameters by the tool, click and select the parameters you want.
Otherwise, do not select anything and click “Create MACBIN.xls”.

We assume that the username and password of PPPoE is composed of 8 bit random characters.
Select them and enter a digit such as 8, input the total number of configuration files such as 100.
Click “Create MACBIN.xls”.

Figure 3-4

3. Open the relevant MACBIN.xls, and input the MAC addresses of the 100pcs devices. You can
find the coloums of PPPoE Username and Password was filled out with random values. Save
after completion.

Figure 3-5

 Note: You can get the list of MAC address from manufacture.
5
4. Click the “Completed MACBIN.xls” button and select the excel table you just saved, then
click and select “MAC.bin output path”, the “MAC.bin” file will be automatically produced
in the folder you choosed.

Figure 3-6

 Note:
a) The exported configuration file is one “xxxxx.bin” file based on MAC address, such as
“7C8BCA5718DC.bin”. One file for one device.
b) For PPPoE and Static IP, need to build up one PPPoE or Static IP connection in general
config mode first, then can set PPPoE account and static IP parameters in specific config
mode.

3.3 Logo Config and Favicon Config

You can change your ISP logo and Favicon by Logo Config and Favicon Config.

Figure 3-7

Prepare the Favicon and Logo file you want to change. The Logo file must be named as logo-
icon.png and the Favicon file must be named as favicon.ico.

 Note: The Favicon and Logo file can not exceed 6KB.
6
Chapter 4. Upgrading the devices

Create a new folder on the computer, such as D:\TP-Link Agile Config. Import all the configuration
files into the folder.

4.1 Topology

Figure 4-1

 Note: Plug the PC to the switch first, then plug the WAN port of the device to the switch,
the device will be upgraded automatically.

4.2 Upgrading process

1. IP Address setting

Set the IP address and subnet mask as “192.168.66.10, 255.255.255.0”, and click Save.

2. Import the configuration file by clicking the buttons and selecting the files.

7
 Figure 4-2

3. Plug the WAN port of the device to the switch, power the device on, then the device will be
upgraded automatically. It supports upgrading the devices in batches, according to amount of
the ports on switch.

 Note:
a) All LEDs are lit to indicate the Agile Config has started.
b) All LEDs flashes indicate the Agile Config is successful.

8
Chapter 5. FAQ

1. How to reconfigure a configured device?

a) Power the device on and connect to one PC.

b) Run a chat cmd.exe on the PC, enter “telnet 192.168.0.1”(LAN IP address of the device)
to login the device within 10 minutes of the device being powered on.

c) Enter “reset” for password, then the cmd.exe will show “You can reset to TP-Link Config
now.”

d) Press the reset button on the device for more than 5s. The device will reboot, once the
reset process is completed, the device will have the default TP-Link factory configuration.
Then you can configure the device again via Agile Config.

2. How do you configure the device's SSID to be formatted with MAC address?
If the SSID of each device needs to be unique based on their MAC addresses, please set the
SSID as “WISP_XXXX_2G” in General Config. Here, XXXX will be replaced with the last
N bits of the MAC address (N is the number of Xs you enter). For example, when the MAC
address is 8D6C7298D0A and the SSID is set as WISP_XXXX_2G, the new SSID will be
WISP_8D0A_2G. If the SSID is WISP_XXXXXX, it will be WISP_298D0A.
3. How to configure the Wireless password of each device to be unique?
Please set the wireless password to be “?undefined?” in General Config, the password of each
device will be the same as its PIN after set by Agile Config.