Winstar LCD Display Module

Mikroe Part Number: Mikroe-4

Manufacturer: Winstar Display Co., LTD

Module Number: WDG0151-TMI-V#N00

 Winstar Display Co., LTD
華凌光電股份有限公司
住址: 407 台中市中清路 163 號 WEB: http://www.winstar.com.tw
No.163 Chung Ching RD., E-mail: [email protected]
Taichune, Taiwan, R.O.C Tel:886-4-24262208 Fax：886-4-24262207

SPECIFICATION

CUSTOMER :

MODULE NO.: WDG0151-TMI-V#N00

APPROVED BY:

( FOR CUSTOMER USE ONLY ) PCB VERSION: DATA:

SALES BY APPROVED BY CHECKED BY PREPARED BY

VERSION DATE REVISED SUMMARY

PAGE NO.
0 2009/11/10 First issue

Page 1 of 30
 Winstar Display Co., LTD MODLE NO：
華凌光電股份有限公司
DOC. FIRST ISSUE
RECORDS OF REVISION

REVISED
VERSION DATE SUMMARY
PAGE NO.
0 2009/11/10 First issue

Page 2 of 30
Contents

1.Module classification information

2.Precautions in Use of LCM

3.General Specification

4.Absolute Maximum Ratings

5.Electrical Characteristics

6.Optical Characteristics

7.Interface Pin Function

8.Counter Drawing & Block Diagram

9.Timing Characteristics

10.Display Control Instruction

11.Detailed Explanation

12.Reliability

13.Backlight Information

14.Inspection specification

15.Material List of Components for RoHs

Page 3 of 30
1.Module Classification Information
W D G 0151－ T M I－ V# N00

   

Brand：WINSTAR DISPLAY CORPORATION

 Custom：D

 Display Type：H→ Character Type ; G→ Graphic Type N → LCD Display

 Model serials no.0000 - ZZZZ

 Backlight Type： N→ Without backlight P→ LED, Blue

B→ EL, Blue green A→ LED, Amber

D→ EL, Green R→ LED, Red

W→ EL, White O→ LED, Orange

F→ CCFL, White G→ LED, Green

Y→ LED, Yellow Green T→ LED, White

 LCD Mode： B→ TN Positive, Gray T→ FSTN Negative

N→ TN Negative,

G→ STN Positive, Gray

Y→ STN Positive, Yellow Green

M→ STN Negative, Blue

F→ FSTN Positive

 LCD Polarizer A→ Reflective, N.T, 6:00 H→ Transflective, W.T,6:00

Type/ D→ Reflective, N.T, 12:00 K→ Transflective, W.T,12:00

Temperature G→ Reflective, W. T, 6:00 C→ Transmissive, N.T,6:00

range/ View J→ Reflective, W. T, 12:00 F→ Transmissive, N.T,12:00

direction B→ Transflective, N.T,6:00 I→ Transmissive, W. T, 6:00

E→ Transflective, N.T.12:00 L→ Transmissive, W.T,12:00

 Special Code V：Build in Negative Voltage N：IC NT7107，NT7108C

# : Fit in with the ROHS Directions and regulations;

0:Sales code 0:Version

Page 4 of 30
2.Precautions in Use of LCD Module
(1)Avoid applying excessive shocks to the module or making any alterations or modifications to it.

(2)Don’t make extra holes on the printed circuit board, modify its shape or change the components of

LCD Module.

(3)Don’t disassemble the LCM.

(4)Don’t operate it above the absolute maximum rating.

(5)Don’t drop, bend or twist LCM.

(6)Soldering: only to the I/O terminals.

(7)Storage: please storage in anti-static electricity container and clean environment.

(8). Winstar have the right to change the passive components

(9). Winstar have the right to change the PCB Rev.

3.General Specification
ITEM STANDARD VALUE UNIT

Number of dots 128 ×64 dots

Outline dimension 78.0 (W) ×70.0 (H) ×14.3 (T) mm

View area 62.0(W) ×44.0(H) mm

Active area 56.3(W) ×38.38(H) mm

Dot size 0.42(W) ×0.58(H) mm

Dot pitch 0.44(W) ×0.60(H) mm

LCD type STN Negative, Blue, Transmissive

(In LCD production, It will occur slightly color difference. We can
only guarantee the same color in the same batch.)
View direction 6 o’clock

Backlight LED , White

Page 5 of 30
4.Absolute Maximum Ratings
ITEM SYMBOL MIN. TYP. MAX. UNIT

Operating Temperature TOP -20 － +70 ℃

Storage Temperature TST -30 － +80 ℃

Input Voltage VI 0 － VDD V

Supply Voltage For Logic VDD-VSS 0 － 6.5 V

Supply Voltage For LCD VDD-VLCD 0 － 17.0 V

5.Electrical Characteristics
ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT

Logic Voltage VDD-VSS － 4.5 5.0 5.5 V

Supply Voltage For Ta=-20℃ － － － V

LCD Ta=25℃
VDD-VO 7.62 8.51 9.26 V
*Note
Ta=+70℃ － － － V

Input High Volt. VIH － 2.0 － VDD V

Input Low Volt. VIL － 0 － 0.8 V

Output High Volt. VOH － 2.4 － VDD V

Output Low Volt. VOL － 0 － 0.4 V

Supply Current IOP 5.0 2.8 3.1 3.4 mA

* Note: Please design the VOP adjustment circuit on customer's main board

Vdd
LCM
VR Vo
10K~20K Module
Vee

Page 6 of 30
6.Optical Characteristics
ITEM SYMBAL CONDITION MIN TYP MAX UNIT
(V)θ CR≧ 2 20 － 40 deg.
View Angle
(H)φ CR≧ 2 -30 － 30 deg.

Contrast Ratio CR － － 3 － －

T rise － － 200 300 ms

Response Time
T fall － － 150 200 ms
6.1 Definitions

( Visual angle direction )

Z Brightness at selected state ( BS )
CR =
Brightness at non-selected state ( Bns )
Selected state
Brightness (%)

Non-selected state

X φ
Bs

Bns
θY Operating voltage for LCD driving

■ View Angles ■ Contrast Ratio

■ Response time

Nonselected Condition Selected Condition Nonselected Condition

90 %
Brightness

100 %

10 %

tr Page 7 of 30 td
Rise Time Decay Time ( fall time tf )
7.Interface Pin Function
Pin No. Symbol Level Description

1 CS1 L Select Segment 1 ~ Segment 64

2 CS2 L Select Segment 65 ~ Segment128

3 Vss 0V Ground

4 VDD 5.0V Supply voltage for logic

5 VO (Variable) Operating voltage for LCD

6 D/I H/L H: Data , L: Instruction

7 R/W H/L H: Read(MPU Module) , L :Write(MPU→ Module)

8 E H Enable signal

9 DB0 H/L Data bus line

10 DB1 H/L Data bus line

11 DB2 H/L Data bus line

12 DB3 H/L Data bus line

13 DB4 H/L Data bus line

14 DB5 H/L Data bus line

15 DB6 H/L Data bus line

16 DB7 H/L Data bus line

17 RST L Reset the LCM

18 VEE Negative Voltage Output

19 A Power supply for B/L(+)

20 K Power supply for B/L(-)

Page 8 of 30
8.Counter Drawing & Block diagram

7 8 .0 0 .5 1 CS1
2 .0 7 4 .0 2 CS2
8 .0 6 2 .0 (V A ) 3 V ss
1 0 .8 5 5 6 .3 (A A ) 4 VDD
1 3 .0 P 2 .5 4 * 1 9 = 4 8 .2 6
1 4 .3 M a x 5 Vo

2.54

2.54
1 .8 2 0 - 1 .0 P T H 9 .7 6 D /I
2 0 - 2 .0 P A D 7 R /W
7.4

8 E
13.0

15.81

1 20
9 DB0
10 DB1
11 DB2
12 DB3
38.38(AA)
70.0 0.5

44.0(VA)

1 2 8 X 6 4 D o ts

64.92
55.2

13 DB4
14 DB5
15 DB6
16 DB7
17 RST
18 VEE
19 A
4 - 2 .5 P T H 1 .6
5 .0 6 8 .0 4 - 5 .0 P A D 20 K
L E D B /L

0 .4 4
0 .4 2 T h e n o n -sp e cified to le ran c e o f d im e n sio n is 0 .3 m m .
0.58
0.6

D O T S IZ E
S C A L E 1 0 /1

Page 9 of 30
 NT7107C

Com Driver
Com1~64
128X64 DOT

FR,M,CL,CLK1,CLK2
NT7108C NT7108C
Seg1~64 Seg65~128
Seg Driver Seg Driver

Power Circuit
Vdd

Bias and
E VO VR
MPU Vss 10K or 20K
D/I
R/W
80 series
or DB0~DB7
68 series Vee

Generator
CS1

N.V.
CS2
RST
Power on
Optional
reset circuit

External contrast adjustment.

Page 10 of 30
9.Timing Characteristics
MPU Interface (T=25℃, VDD=+5.0V±0.5)

Characteristic Symbol Min Typ Max Unit

E cycle tcyc 1000 － － ns
E high level width twhE 450 － － ns
E low level width twlE 450 － － ns
E rise time tr － － 25 ns
E tall time tf － － 25 ns
Address set-up time tas 140 － － ns
Address hold time tah 10 － － ns
Data set-up time tdsw 140 － － ns
Data delay time tddr － － 320 ns
Data hold time (write) tdhw 10 － － ns
Data hold time (read) tdhr 20 － － ns

Page 11 of 30
Page 12 of 30
10.Display Control Instruction
The display control instructions control the internal state of the NT7108. Instruction is received from

MPU to NT7108 for the display control. The following table shows various instructions.

Page 13 of 30
11.Detailed Explanation

The display data appears when D is 1 and disappears when D is 0. Though the data is not on the

screen with D=0, it remains in the display data RAM. Therefore, you can make it appear by

changing D=0 into D=1.

SET ADDRESS (Y ADDRESS)

Y address (AC0-AC5) of the display data RAM is set in the Y address counter. An address is set by

instruction and increased by 1 automatically by read or write operations of display data.

SET PAGE (X ADDRESS)

X address (AC0-AC2) of the display data RAM is set in the X address register. Writing or reading to

or from MPU is executed in this specified page until the next page is set.

DISPLAY START LINE (Z ADDRESS)

Z address (AC0-AC5) of the display data RAM is set in the display start line register and displayed

at the top of the screen. When the display duty cycle is 1/64 or others (1/32-1/64), the data of total
line number of LCD screen, from the line specified by display start line instruction, is displayed.

Page 14 of 30
STATUS READ

BUSY

When BUSY is 1, the Chip is executing internal operation and no instructions are accepted.

When BUSY is 0, the Chip is ready to accept any instructions.

ON/OFF

When ON/OFF is 1, the display is OFF.

When ON/OFF is 0, the display is ON.

RESET

When RESET is 1, the system is being initialized.

In this condition, no instructions except status read can be accepted.

When RESET is 0, initializing has finished and the system is in usual operation condition.

WRITE DISPLAY DATA

Writes data (D0-D7) into the display data RAM. After writing instruction, Y address is increased by

1automatically.

READ DISPLAY DATA

Reads data (D0-D7) from the display data RAM. After reading instruction, Y address is increased by

1 automatically.

Page 15 of 30
12.RELIABILITY
℃)
Content of Reliability Test (wide temperature, -20℃~70℃

Environmental Test
Test Item Content of Test Test Condition Note
High Temperature Endurance test applying the high storage 80℃ 2
storage temperature for a long time. 200hrs
Low Temperature Endurance test applying the high storage -30℃ 1,2
storage temperature for a long time. 200hrs
Endurance test applying the electric stress
High Temperature 70℃
(Voltage & Current) and the thermal stress to ——
Operation 200hrs
the element for a long time.
Low Temperature Endurance test applying the electric stress -20℃ 1
Operation under low temperature for a long time. 200hrs
The module should be allowed to stand at 60
℃,90%RH max
High Temperature/ For 96hrs under no-load condition excluding 60℃,90%RH
1,2
Humidity Operation the polarizer, 96hrs
Then taking it out and drying it at normal
temperature.
The sample should be allowed stand the
following 10 cycles of operation

Thermal shock -20℃ 25℃ 70℃

-20℃/70℃ ——
resistance 10 cycles
30min 5min 30min
1 cycle
Total fixed amplitude :
1.5mm
Vibration Frequency :
Endurance test applying the vibration during
Vibration test 10~55Hz 3
transportation and using.
One cycle 60 seconds to
3 directions of X,Y,Z
for Each 15 minutes

Endurance test applying the electric stress to VS=800V,RS=1.5k

Static electricity test CS=100pF ——
the terminal.
1 time

Note1: No dew condensation to be observed.

Note2: The function test shall be conducted after 4 hours storage at the normal
Temperature and humidity after remove from the test chamber.

Page 16 of 30
Note3: Vibration test will be conducted to the product itself without putting it in a container.

Page 17 of 30
 13.Backlight Information
PARAMETER SYMBOL MIN TYP MAX UNIT TEST CONDITION

Supply Current ILED 57.6 64 100 mA V=3.5V

Supply Voltage V 3.4 3.5 3.6 V

Reverse Voltage VR － － 5 V

Luminous Intensity IV 282 344 － CD/M2 ILED=64mA

LED Life Time － 50K － Hr. ILED 64mA

(For Reference ℃,50-60%RH,
25℃
only) (Note 1)

Color White

Note: The LED of B/L is drive by current only, drive voltage is for reference only.

drive voltage can make driving current under safety area (current between

minimum and maximum).

Note1 :50K hours is only a estimate for reference.

2.Drive from pin19,pin20

R
A
B/L
K

LCM

Page 18 of 30
14. Inspection specification
NO Item Criterion AQL

1.1 Missing vertical, horizontal segment, segment contrast defect.

1.2 Missing character , dot or icon.
1.3 Display malfunction.
Electrical 1.4 No function or no display.
01 0.65
Testing 1.5 Current consumption exceeds product specifications.
1.6 LCD viewing angle defect.
1.7 Mixed product types.
1.8 Contrast defect.

Black or white 2.1 White and black spots on display 0.25mm, no more than
02 spots on LCD three white or black spots present. 2.5
(display only) 2.2 Densely spaced: No more than two spots or lines within 3mm

3.1 Round type : As following drawing

2.5

LCD black
spots, white
03 spots,
contamination
(non-display)

3.2 Line type : (As following drawing)

Length Width Acceptable Q TY
--- W Accept no dense
L 0.02 W 2.5
2
L 0.03 W
--- 0.05 W As round type

Page 19 of 30
 If bubbles are visible, Size Acceptable Q TY
judge using black spot
specifications, not easy Accept no dense
to find, must check in
Polarizer specify direction.
04 2.5
bubbles 3
2
0
Total Q TY 3

Page 20 of 30
NO Item Criterion AQL
05 Scratches Follow NO.3 LCD black spots, white spots, contamination

Symbols Define:
x: Chip length y: Chip width z: Chip thickness
k: Seal width t: Glass thickness a: LCD side length
L: Electrode pad length:

6.1 General glass chip :

6.1.1 Chip on panel surface and crack between panels:

C C C

Chipped
06 2.5
glass

C C C

Page 21 of 30
NO Item Criterion AQL

x: Chip length y: Chip width z: Chip thickness

k: Seal width t: Glass thickness a: LCD side length
L: Electrode pad length
6.2 Protrusion over terminal :
6.2.1 Chip on electrode pad :

C C C

Glass
06 cra 2.5
ck

C C C

Page 22 of 30
 L

Page 23 of 30
NO Item Criterion AQL
07 Cracked glass LCD 2.5

0.65
Backlight 2.5
08
elements LCD
0.65

2.5
09 Bezel
0.65

C 2.5
2.5
0.65
C C
The height of the COB should not exceed the height indicated in the 2.5
assembly diagram.
10.4 There may not be more than 2mm of sealant outside the seal area on 2.5
the PCB. And there should be no more than three places. 0.65
10.5 No oxidation or contamination PCB terminals.
10 PCB COB 10.6 Parts on PCB must be the same as on the production characteristic
chart. There should be no wrong parts, missing parts or excess 0.65
parts.
10.7 The jumper on the PCB should conform to the product characteristic 2.5
chart.
10.8 If solder gets on bezel tab pads, LED pad, zebra pad or screw hold 2.5
pad, make sure it is smoothed down.
10.9 The Scraping testing standard for Copper Coating of PCB

X
Y
X * Y<=2mm2
2.5
C 2.5
2.5
0.65

11 Soldering
C
C

Page 24 of 30
NO Item Criterion AQL

2.5
L C

L C 0.65

2.5

2.5
C C 2.5

2.5
General
12
appearance
2.5

0.65

0.65

0.65
LCD

0.65

Page 25 of 30
Page 26 of 30
15. Material List of Components for
RoHS

1. WINSTAR Display Co., Ltd hereby declares that all of or part of products (with the mark

“#”in code), including, but not limited to, the LCM, accessories or packages, manufactured

and/or delivered to your company (including your subsidiaries and affiliated company)

directly or indirectly by our company (including our subsidiaries or affiliated companies) do

not intentionally contain any of the substances listed in all applicable EU directives and

regulations, including the following substances.

Exhibit A：The Harmful Material List

Material (Cd) (Pb) (Hg) (Cr6+) PBBs PBDEs

Limited 100 1000 1000 1000 1000 1000

Value ppm ppm ppm ppm ppm ppm

Above limited value is set up according to RoHS.

2.Process for RoHS requirement：

(1) Use the Sn/Ag/Cu soldering surface the surface of Pb-free solder is rougher than we used before.

(2) Heat-resistance temp.：

Reflow：250 ,30 seconds Max.

Connector soldering wave or hand soldering：320 , 10 seconds max.

(3) Temp. curve of reflow, max. Temp.：235±5

Recommended customer’s soldering temp. of connector：280 , 3 seconds.

Page 27 of 30
Page 28 of 30
 winstar LCM Sample Estimate Feedback Sheet
：
Module Number： Page: 1
1 Panel Specification：
1. Panel Type： Pass NG ,
2. View Direction： Pass NG ,
3. Numbers of Dots： Pass NG ,
4. View Area： Pass NG ,
5. Active Area： Pass NG ,
6. Operating Temperature： Pass NG ,
7. Storage Temperature： Pass NG ,
8. Others：
2 Mechanical Specification：
1. PCB Size： Pass NG ,
2. Frame Size： Pass NG ,
3. Materal of Frame： Pass NG ,
4. Connector Position： Pass NG ,
5. Fix Hole Position： Pass NG ,
6. Backlight Position： Pass NG ,
7. Thickness of PCB： Pass NG ,
8. Height of Frame to PCB： Pass NG ,
9. Height of Module： Pass NG ,
10. Others： Pass NG ,
：
3 Relative Hole Size：
1. Pitch of Connector： Pass NG ,
2. Hole size of Connector： Pass NG ,
3. Mounting Hole size： Pass NG ,
4. Mounting Hole Type： Pass NG ,
5. Others： Pass NG ,
4 Backlight Specification：
1. B/L Type： Pass NG ,
2. B/L Color： Pass NG ,
3. B/L Driving Voltage (Reference for LED Type)： Pass NG ,
4. B/L Driving Current： Pass NG ,
5. Brightness of B/L： Pass NG ,
6. B/L Solder Method： Pass NG ,
7. Others： Pass NG ,
Go to page 2

29 30
 winstar
Module Number： Page: 2

5 Electronic Characteristics of Module：

1. Input Voltage： Pass NG ,

2. Supply Current： Pass NG ,

3. Driving Voltage for LCD： Pass NG ,

4. Contrast for LCD： Pass NG ,

5. B/L Driving Method： Pass NG ,

6. Negative Voltage Output： Pass NG ,

7. Interface Function： Pass NG ,

8. LCD Uniformity： Pass NG ,

9. ESD test： Pass NG ,

10. Others： Pass NG ,

6 Summary：

：
Sales signature：

：
Customer Signature： ：
Date： / /

30 30