Scribd Logo
Upload

Welcome to Scribd!

  • 218 views

    Swipguard: Installation Guide

    Uploaded by

    fasihul
    The document provides specifications for the Tempress SwipGuard type P1360 pressure switch, including: - Three versions with different pressure ranges and repeatability of ±0.5-1% FS. - Response time less than 4ms and maximum switch frequency of 30/min. - Lifetime of over 100,000 cycles mechanically and 1,000,000 cycles electrically. - Electrical specifications including SPDT contact arrangement and load capacity. - Mechanical specifications like materials, connections, and weight of 0.4kg. - Environmental conditions of -10°C to +70°C operating temperature.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Swipguard: Installation Guide

    Uploaded by

    fasihul
    218 views2 pages
    The document provides specifications for the Tempress SwipGuard type P1360 pressure switch, including: - Three versions with different pressure ranges and repeatability of ±0.5-1% FS. - Response time less than 4ms and maximum switch frequency of 30/min. - Lifetime of over 100,000 cycles mechanically and 1,000,000 cycles electrically. - Electrical specifications including SPDT contact arrangement and load capacity. - Mechanical specifications like materials, connections, and weight of 0.4kg. - Environmental conditions of -10°C to +70°C operating temperature.

    Original Title

    000907m_Rev_E

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides specifications for the Tempress SwipGuard type P1360 pressure switch, including: - Three versions with different pressure ranges and repeatability of ±0.5-1% FS. - Response time less than 4ms and maximum switch frequency of 30/min. - Lifetime of over 100,000 cycles mechanically and 1,000,000 cycles electrically. - Electrical specifications including SPDT contact arrangement and load capacity. - Mechanical specifications like materials, connections, and weight of 0.4kg. - Environmental conditions of -10°C to +70°C operating temperature.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    218 views2 pages

    Swipguard: Installation Guide

    Uploaded by

    fasihul
    The document provides specifications for the Tempress SwipGuard type P1360 pressure switch, including: - Three versions with different pressure ranges and repeatability of ±0.5-1% FS. - Response time less than 4ms and maximum switch frequency of 30/min. - Lifetime of over 100,000 cycles mechanically and 1,000,000 cycles electrically. - Electrical specifications including SPDT contact arrangement and load capacity. - Mechanical specifications like materials, connections, and weight of 0.4kg. - Environmental conditions of -10°C to +70°C operating temperature.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    P1360 Specifikations

    Standard ranges Ver. 1 +1 +10 bar


    Ver. 2 +7 +35 bar
    Ver. 3 +25 +125 bar
    Repeatability ± 0.5% FS (typical)
    ± 1% FS (max. allowable)
    Response time
    Max. switch frequency
    Life time Mechanical
    < 4 ms
    30/min. (0.5 Hz)
    > 100.000 cycles at 80 °C
    SwipGuard
    Electrical at max. > 1.000,000 cycles Type P1360
    contact load
    Pressure Ver.1 Ver.2
    Max. operating pressure 10bar 35bar
    Test pressure 15bar 53bar
    Burst pressure >40bar >140bar
    Electrical specifications
    Switches Contact arrangement SPDT
    Contact load DC resistive 5 A, 24V
    DC inductive 4 A, 24V
    Leakage signal. Capacitive NPN Max. 100 MA, 24 V
    Mechanical specifications
    Pressure connection Thread or Dimension & design acc. to
    diaphragm seal order
    Electrical connection Plug IEC529, IP65, M20x1.5
    Internal material Bellow Bronze
    O-ring NBR
    External material Housing AISI304
    Plug fixture Glass filled polyamide, PA 6.6
    Weight 0.4 kg
    Environmental conditions
    Temperature Ambient and Operation,
    only with liquid. -10 to +70°C

    Enclosure
    Transport -40 to +80°C
    IEC529, IP65
    Installation guide
    Vibration stability, 4 g, 25 Hz – 100 Hz IEC60028-2-6
    sinusoidal
    Hysteresis Typical 5-10 % Not less than 3% T20
    Nordlandsvej 64-66,
    Not less than 5% T70 DK-8240 Risskov
    Tel. +45 89 32 52 00
    Fax. +45 89 32 52 13
    E-mail: [email protected] 0038
    Item: 000907-001. Rev. E. Date: 2017-01-03.

    Thank you for choosing Tempress’ SwipGuard, type P1360.


    Please make sure the set point corresponds to your
    specifications. Also check that the operating span corresponds A B
    to the maximum pressure expected for the installation.
    Mechanical
    To comply with the PED requirements for redundancy the
    equipment must be installed in such a way that two
    mechanical independent switches are attached to the same
    pressure carrying system. This set-up is shown in fig. 1. The
    CE marking is only valid when the installation is made to Fig. 1 – mechanical installation
    comply with this principle.
    Electrical security circuitry
    To comply with the requirements for incorporating the signal in
    the security circuitry, the two switches must be connected in
    series. This set-up is shown in fig. 2. The CE marking is only
    valid when the installation is made to comply with this
    principle.

    Electrical process circuitry


    The switch is fitted with a second switch, which can be used
    as a process surveillance switch. This set-up is shown in fig.
    3. This switch can be delivered as NO (normally open) or NC
    (normally closed). The actual setting will appear on the label.
    The internal leakage surveillance appears as a NPN signal. Fig. 2 – part of security circuitry
    Maintenance
    To make sure that the switches operate as intended, the
    preset switch point should be tested once a year by means of
    a controlled pressure. Either after a cleaning process in place,
    or by moving the switches to a test-rig. The housing resists
    common cleaning agents and should be dried after cleaning.
    The top cover is never to be removed! Tampering with the
    sealing will void any and all guarantee of setting as well as
    approval according to the PED. Note that a readjustment can
    only take place at Tempress A/S.
    The switches should not be exposed to mechanical impact. Fig. 3 – part of process surveillance circuitry
    The electrical connection is IP65.
    P1360 Specifikationer
    Standard anvendelse Ver. 1 +1 +10 bar
    Ver. 2 +7 +35 bar
    Ver. 3 +25 +125 bar
    Gentagelses nøjagtighed ± 0.5% FS (typisk)

    Reaktionstid
    Max. kontakt frekvens
    ± 1% FS (max. tilladt)
    < 4 ms
    30/min. (0.5 Hz)
    SwipGuard
    Levetid Mekanisk > 100.000 gange ved 80 Type P1360
    Elektrisk ved max. °C
    kontakt belastning > 1.000,000 gange
    Tryk Ver.1 Ver.2
    Max. arbejdstryk 10bar 35bar
    Prøvetryk 15bar 53bar
    Sprængningstryk >40bar >140bar
    Elektriske specifikationer
    Kontakter Kontakt arrangement SPDT
    Kontakt belastning DC modstand 5 A, 24V
    DC induktiv 4 A, 24V
    Lækage signal. kapasitiv NPN Max. 100 MA, 24 V
    Mekaniske specifikationer
    Tryktilslutning Gevind eller Dimension & design efter
    trykformidler ordre
    Elektrisk tilslutning Stik IEC529, IP65, M20x1,5
    Indvendigt materiale Bælg Bronze
    O-ring NBR
    Udvendig materiale Hus AISI304
    Stik Glasfyldt polyamid, PA 6.6
    Vægt 0,4 kg
    Installationsbetingelser
    Temperatur Omgivelse og drift,
    kun med væske.
    Transport
    -10 to +70°C
    -40 to +80°C
    Installationsvejledning
    Tæthed IEC529, IP65
    Vibrations stabilitet, 4 g, 25 Hz – 100 Hz IEC60028-2-6
    sinuskurve Nordlandsvej 64-66,
    Hysterese Typisk 5-10 % Ikke mindre end 3% T20 DK-8240 Risskov
    Ikke mindre end 5% T70 Tel. +45 89 32 52 00
    Fax. +45 89 32 52 13
    E-mail: [email protected] 0038
    Item: 000907-001. Rev. D. Date: 2007-01-05.

    Tak fordi I valgte Tempress’ SwipGuard, type P1360. Undersøg


    venligst at set-punktet stemmer overens med specifikationerne.
    A B
    Ligeledes undersøg at operationsområdet stemmer overens med
    det forventede maksimale tryk for installationen.

    Mekanisk
    For at overholde kravene i PED for redundans skal Tempress’
    SwipGuard Type P1360 installeres således, at to mekanisk
    uafhængige switche er monteret på det samme trykbærende
    rørsystem. Den principielle montage er vist i fig. 1. CE Fig. 1 – mekanisk installation
    mærkningen er kun gyldig, når installationen er gennemført i
    overensstemmelse med de nævnte principper.

    Elektrisk sikkerhedskreds
    For at overholde kravene i PED for samling af signal i
    sikkerhedskredsen skal de to switche forbindes i serie. Dette er
    vist i
    fig. 2. CE mærkningen er kun gyldig, når installationen er
    gennemført i overensstemmelse med de nævnte principper.

    Elektrisk proceskreds
    Switchene er udstyret med endnu en switch, som kan anvendes
    til overvågning af processen. Dette er vist i fig. 3. Switchen kan
    leveres som NO (normal åben) eller NC (normal lukket). Den
    aktuelle indstilling vil fremgå af label. Den interne Fig. 2 – del af sikkerhedskredsløb
    lækageovervågning fremkommer som et ”NPN” signal.

    Vedligeholdelse
    For at sikre at switchene virker som tilsigtet, skal switch-punkt
    afprøves én gang pr. år ved hjælp af et kontrolleret tryk. Dette kan
    udføres enten i forbindelse med ”CIP” eller ved at demontere
    switchene og gennemføre testen i en prøveopstilling. Instrumentet
    tåler de fleste rengøringsmidler og bør aftørres efter rengøring.
    Topdæksel må IKKE demonteres! Bemærk at al garanti for
    justering, indstilling og myndighedsgodkendelse bortfalder, hvis
    plomberingen er brudt. Bemærk desuden at genjustering kun kan
    finde sted hos Tempress. Switchene bør ikke udsættes for Fig. 3 – del af procesovervågningskredsløb
    mekanisk overlast. IP tætheden er 65.

    You might also like