Service: Non Corrosive Hydrocarbons - Glycol - Blow Down Vents - Drains (T 120°C)

Download as pdf or txt
Download as pdf or txt
You are on page 1of 1

SERVICE: NON CORROSIVE HYDROCARBONS –

ITEM 3A1 CORR.ALLOWANCE 1.5 mm


GLYCOL – BLOW DOWN VENTS – DRAINS (T ≤ 120°C)

CODES-Design: ASME B31.4/B16.5/B16.34


Rating & Facing 300 # RF
DESIGN CONDITIONS
REFERANCE SPECIFICATIONS : ---- T1 : 0 to 55 °C T2 : 70 °C T3 : 93 °C
---- ---- P1 : 49.6 bar P2 : 48.3 bar P3 : 46.5 bar
S.W. FITTINGS A 105 / 6000# SW ---

THDD FITTINGS A 105 / 3000# NPT ---

NORMAL (from pipe) API 5L Gr.B / SMLS ---


NIPPLES

SWAGES (from pipe) API 5L Gr.B / SMLS

SCHEDULE N° -- 160 160 160 160 160

NOMINAL SIZE INCH -- 1/2” 3/4" 1” 11/2” 2” 21/2” 3” 4” 6” 8” 10” 12” 14” 16” 18” 20” 24” 30” 36”

WALL THK. mm -- 4,78 5,56 4,55 5,08 5.54 5,16 5,49 6,02 7,11 6.35 6.35 6.35 7.92 7.92 9.43 --- --- --- ---
PIPES

SCHEDULE N° -- 160 160 80 80 80 40 40 40 40 20 20 20 20 20 STD --- --- --- ---

0 MATERIAL ASTM A 106Gr. B


MANIFACTURE SMLS ERW

WELDING NECK A 105 / 300# - RF


SOCKET WELD A 105 / 300# - RF
FLANGES

THREADED A 105 / 300# - RF

SLIP ON
LAP JOINT
BLIND A 105 / 300# - RF
Spiral Wound, 304 S.S. With Soft Steel Centering Ring
GASKETS
STUD BOLTS & NUTS A 193 Gr.B7 / A 194 Gr.2H (ZINC COATED ) (NOTE 1)

RED.THDD FLG.S A 105


COMPONENTS

RED.S.O.FLG.S
DRIP RINGS A 105
SPECTACLE BLINDS A 105
SPACERS & BLIND A 105
TEMP.STRAINERS AISI 316
VB 04 – NPT/SW VB 02 – RF
BALL VALVE
VB 02 – RF VBF 02 – RF (NOTE 2)
VGT 04 –NPT/SW VGT 02 – RF
GATE VALVE
VGT 02 – RF
VALVES

VGL 04 –NPT/SW VGL 02 – RF


GLOBE VALVE
VGL 02 – RF

NEEDLE VALVE VN 04 – NPT

BUTERFLY VALVE VBS 02 – RF


VPC 04 – NPT/SW VSC 02 – RF
CHECK VALVE
VWC 02 – RF

“ Y “ STRAINERS FT 04 – NPT/SW FT 02 – RF

90°-45° ELBOWS A 234 Gr.WPB


ECC.CONC.REDUCTIONS A 234 Gr.WPB
1/2 (3)(5) ELLIPT.CAPS A 234 Gr.WPB
3/4 (3)(5) L.J STUB ENDS
1 (4)(6) (3)(5) PIPE BENDS

11/2 (3)(5) Mark Components Material Mark Components Material


2 (1) (1) STRAIGHT BW TEE A 234 Gr.WPB (7) SWEEPOLETS
3 (1) (2) REDUCTION BW TEE A 234 Gr.WPB (8) WELDOLETS A 105

4 (1) (3) STRAIGHT THDD TEE A 105 (9) THREDOLETS A 105


DN” HEADER SIZE

6 (1) (4) REDUCTION THDD TEE A 105 (10) SOCKOLETS A105


8 (1) (5) STRAIGHT SW TEE A105 (11) NIPOLETS THDD A 105
10 (1) (6) REDUCTION SW TEE A105 (12) PIPE TO PIPE
(9) NOTES:
12 (1)
(10) 1) All carbon steel bolting on flanges, valves & “Y” strainers shall be
14 (1)
(11) zinc coating (hot-dip) to ASTM A-153.
16 (8) (2) (1) 2) To be used where required by P&I drawings only.

18 (1) 3) Threaded Ends and connections are allowed for instrument taps only.

20 (1)
24 (1)
30

36

1/2 3/4 1 11/2 2 3 4 6 8 10 12 14 16 18 20 24 30 36

DN” BRANCH SIZE

You might also like