Scribd Logo
Upload

Welcome to Scribd!

  • 51 views

    Controll Innerseal - NOORS - For Printshop

    Uploaded by

    Mohamed Abdel-Monem

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Controll Innerseal - NOORS - For Printshop

    Uploaded by

    Mohamed Abdel-Monem
    51 views2 pages

    Original Title

    Controll Innerseal -NOORS- For Printshop

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    51 views2 pages

    Controll Innerseal - NOORS - For Printshop

    Uploaded by

    Mohamed Abdel-Monem

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    technical data sheet

    CONTROLL®INNERSEAL
    Professional Waterproofing

    PRODUCT DESCRIPTION: GENERAL USE: HEAVY DUTY AREAS*:


    Controll®INNERSEAL is a waterborne potassium Garages Agricultural areas
    and sodium silicate specially designed for extremly Roads, Bridges, Tunnels Aquaculture areas
    deep penetration and crystalisation in concrete Potable water areas Biogas silos
    micro pores, capillaries, and micro cracks.
    Warehouses Cold storage rooms
    It’s used for permanent sealing, waterproofing,
    Industry facilities Parking areas
    dustproofing and hardening (increase 35%) of
    concrete surfaces. Prevents damages caused Ports, Marinas Manure deposits / yards
    by penetration of water, salt, acids, sulfur, oil Foundations, Facades Sewage disposal plants
    and other damaging liquids. For rehabilitaion Walkways, Stairs Slaughterhouses
    Controll®INNERSEAL has unique properties to Waste recycling areas
    strenghten concrete, stop/slow down the process of KEY BENEFITS: *In combination with
    carbonation and corrosion on reinforcement. Easy application Controll®INNERSEAL Plus (+)
    Controll®INNERSEAL penetrates deep into the Cost effective
    concrete surface and reacts by producing hard and No peel off or film lift COMPLIES WITH:
    dense calcium silicate hydrate (CSH) into the pore- EN 1504-2 Surface protection
    No efflorescence
    and capillary system. systems for concrete
    No VOC’s
    Because the result of the reaction is embed- DIN 11622-2 Chemical
    ded into the concrete, a treatment with Prolongs concrete lifetime resistance for biogas plants
    Controll®INNERSEAL will outlast traditional Resists stains & dust
    Nuclear powerplant cls
    synthetic surface sealers and ordinary film coat- Easier to clean Green 2 - use in wetwell
    ings and will never break nor flake. Deep penetration UNE-EN ISO 12873-2: 2005
    Controll®INNERSEAL can be used as a complete Seals and densify contact with drinking water
    single treatment. In particularly vulnerable areas
    such as parking garages, manure storage, agricul-
    ture, silos, waste processing etc. we recommend a EN 1504-2: Surface protection systems for concrete
    rich top application of Controll®INNERSEAL Plus (+) Abrasion resistance: 35,4% (> 30 %)
    as a final por/crack filler. Absorption/permeability: 0,09 kg/m2h 0,5 (< 0,09 kg/m2h 0,5)
    Impact resistance: Class II: ≥10 Nm (Class I: ≥4 Nm)
    Controll®INNERSEAL holds no VOC’s, is harmless
    to health, can be used in contact with drinking Adhesion/pull-off test: 2,4 N/mm2 (H: ≥1,0 V: ≥ 1,5)
    water and is environmental friendly. Depth of penetration: 17 mm (≥ 5 mm)

    technical data sheet


    1:2

    Controll Innerseal - NOORS.indd 1 2013-05-02 02:34:17


    technical data sheet

    CONTROLL®INNERSEAL
    Professional Waterproofing

    APPLICATION:
    Controll®INNERSEAL is delivered ready to use and
    is not to be diluted or mixed with other fluids. The
    surface must be free of dust, old paint, oil, waxes
    or other substance that may obstruct absorption.
    Defect concrete/larger cracks must be profes-
    sional prepared in advance. Adjacent polished
    surfaces (e.g. glass, aluminium, tiles, and varnished
    surfaces) should be covered. In case of spray on
    such surfaces, flush/wash immediately using clean
    water. Stir or shake the product.
    Appearance . . . . . . . . . Slightly clouded liquid
    Apply Controll®INNERSEAL with low-pressure
    sprayer. Disperse any pool forming with a soft bris- Active ingredients . . . 100% of total solids
    tle broom, and keep surface evenly and continu- pH. . . . . . . . . . . . . . . . . . 11.4
    ously wet for at least 20 minutes. Add more material VOC content. . . . . . . . . 0 g/L
    where needed. Do not continue to brush or spread Density . . . . . . . . . . . . . 1,135 g/cm3
    out Controll®INNERSEAL if the product begins
    Flash point . . . . . . . . . . No true flash
    to dry. Do not allow excess Controll®INNERSEAL
    puddles to dry on the floor, as it can result in white Freeze point. . . . . . . . . 0° C
    residues. If this still occurs, remove immediately Fire. . . . . . . . . . . . . . . . . Not flammable/not combustible
    with scrubbing. Do not apply in direct sunlight.
    Do not use cleaners with pH < 7.
    WARRANTY:
    DRYING TIME: We have designed, formulated and manufactured
    The surface is ready for foot traffic when dry. Allow Controll®INNERSEAL for optimum performance
    6 hours before exposure to rain/flowing water. and durability. Our commitment to quality is the
    foundation for the extended guarantee coverage we
    COVER RANGE: provide.
    Cover range is 1-4 m2 per litre depending on the Furthermore we guarantee that our product is
    surface suction characteristics. of consistent and high quality, manufactured from
    well tested and proven components supplied by
    TEMPERATURE: renowned ISO-certified contractors and of Norwe-
    gian origin. Controll®INNERSEAL has been tested
    Do not apply Controll®INNERSEAL if temperature
    according to all relevant standards for described
    is below 5°C or above 40°C.
    range of application.
    CLEANING
    Tools: Water. Skin: Water and regular soap.
    MANUFACTURER / DISTRIBUTOR
    ENVIRONMENT:
    Maynor A/S, Kleppsto, NORWAY /
    Controll®INNERSEAL is nontoxic, biodegradable
    Komsol International S.A. SPAIN
    and holds no VOC’s.
    WEB: www.komsol.eu
    SAFETY & HEALTH:
    Make sure of sufficient ventilation in closed areas, UNITED ARAB EMIRATES REPRESENTATIVE:
    due to mist that may irritate airways. Harmful ef-
    Noors Engineering W.L.L.
    fects have not been noted. Nevertheless it is always
    recommended to wear gloves, goggles and boots PO Box 12750
    during application. In general, always remember to Doha, QATAR
    consult the Material Safety Data Sheet before use. TLF: +974 4444-0950
    FAX: +974 4442-8756
    PACKAGING AND STORAGE
    MAIL: [email protected]
    Controll®INNERSEAL is delivered in 20 litre
    WEB: www.noorseng.com
    cans and 1000 litre IBC containers. Storage life is
    minimum 36 months. Ensure can/container is kept
    closed.

    technical data sheet


    2:2

    Controll Innerseal - NOORS.indd 2 2013-05-02 02:34:17

    You might also like