Scribd
Upload
440 views21 pages

Technological Institute of The Philippines - Manila: Signature

1) The document provides problems and solutions related to principles of steel design and plastic moment analysis. 2) Problem 1 involves computing the available strength and maximum service load of a W21x48 beam considering flexure and shear strength. 3) Problem 2 asks to determine the maximum permissible value of a service live load P on a W14x61 beam with continuous lateral support. 4) Problem 5 involves determining the critical net area of a 1/2 inch thick plate with circular cutouts considering different failure modes.

Uploaded by

Platoon Nicart Bejer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
440 views21 pages

Technological Institute of The Philippines - Manila: Signature

1) The document provides problems and solutions related to principles of steel design and plastic moment analysis. 2) Problem 1 involves computing the available strength and maximum service load of a W21x48 beam considering flexure and shear strength. 3) Problem 2 asks to determine the maximum permissible value of a service live load P on a W14x61 beam with continuous lateral support. 4) Problem 5 involves determining the critical net area of a 1/2 inch thick plate with circular cutouts considering different failure modes.

Uploaded by

Platoon Nicart Bejer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 21

TECHNOLOGICAL INSTITUTE OF THE PHILIPPINES – MANILA

COLLEGE OF ENGINEERING AND ARCHITECTURE


CIVIL ENGINEERING DEPARTMENT

PRINCIPLES OF STEEL DESIGN


CE 306

PLATE # 4
Plastic Moment Analysis

RATING

SUBMITTED BY:
1810587 PLATOON N. BEJER SIGNATURE

CE32S2

SUBMITTED TO:
ENGR. JOEVANNIE EMMANUEL C. LUMAGAS

JUNE 1, 2021
PROBLEM 1

A W21 × 48 is used as a simply supported, uniformly loaded beam with a


span length of 50 feet and continuous lateral support. The yield stress,
P. N. A.Fy is
60 ksi. If the ratio of live load to dead load is 3, compute the available
strength and determine the maximum total service load (D+L), in kips/ft, that
can be supported considering the flexure and shear strength of the beam.

a. Use LRFD.

b. Use ASD
SOLUTION:

Properties of W21x48
PROBLEM 2

The beam shown in Figure P5.5-1 is a W14 × 61 of A992 steel and has
continuous lateral support. The load P is a service live load. What is the
maximum permissible value of P?

15’ 15’

FIGURE P5.5-1

a. Use LRFD

b. Use ASD
SOLUTION:

Properties of W14x61

100 mm

10 mm

466.09 mm

For Flange: For Web:

bf 9.99 h 10.875
λ= = =7.4 λ= = =29
2tf 2( 0.675) tw 0.375

E 29,000 E 29,000
λ p=0.38
√ Fy
=0.38
√ 50
=9.152 λ p=3.76
√ Fy
=3.76
√ 50
=90.553

Since λ < λ p, COMPACT Since λ < λ p, COMPACT


PROBLEM 3

50
SOLUTION:

Properties of W14x61
PROBLEM 4

A T-section having a cross section shown has a span of 3.6 m. The location

200mm

40mm

160mm

3.6m
SOLUTION:
PROBLEM 4

A compression member is built up from a W14 X 90 and a W10 x 49, both


A992 steel.

7’’

a. Compute rx and ry for the built-up shape.

b. Compute the available strength for KxL = KyL = 30 feet. Using LRFD and ASD
design.
SOLUTION:

Properties of W14x90 from AISC Properties of W10x49 from AISC


Steel Table: Steel Table:
Moment of Inertia , Ix=∑ ( I + A d 2 )

For Strong Axis: For Strong Axis:

kL kL
=30 ft ¿ ¿ =30 ft ¿ ¿
r r

Slenderness Ratio=69.658 Slenderness Ratio=77.293


Therefore,
PROBLEM 5

Determine the critical net area of the ½ in thick plate shown in the figure

BEJER, PLATOON N.

CONSIDERING FAILURE ABCD

B SOLVING FOR An

An= Ag− A hole

C 1 3 1
An= ( ( ))
2
11−2 +
4 8

An=4.625 i n2

D
CONSIDERING FAILURE ABEF

B SOLVING FOR An

BEJER, PLATOON N. An= Ag− A hole +


S2t
4g

1 3 1 32
( ( )
An= 11−2 + +
2 4 8 4 (6) )
E An=4.813 i n2

CONSIDERING FAILURE ABCEF

B SOLVING FOR An

S2t
An= Ag− A hole +
4g
C
1 3 1 32
An=
2( ( )
11−3 + +
4 8 4 (3) )
E
An=4.563 i n2

F
PROBLEM 5

Determine the critical net area of the ½ in thick plate shown in the figure

BEJER, PLATOON N. 1 ½ ‘’

2 ½ ‘’

1 ½ ‘’

1 ½ ‘’ 3’’ 3’’ 1 ½ ‘’

SECTION FAILED SECTION FAILED


DUE TO SHEAR DUE TO TENSION
SOLVING FOR STRESSES:

BEJER, PLATOON N.

You might also like