Huawei Prep4sure H12-211 v2021-04-28 by Jude 227q

H12-211
Number: H12-211
Passing Score: 800
Time Limit: 120 min
File Version: 1
H12-211
https://www.gratisexam.com/
885CB989129A5F974833949052CFB2F2
Exam A
QUESTION 1
Which of the following authentication methods are supported for Telnet users? (Choose three)
A. Password authentication
B. AAA local authentication

C. MD5 authentication
D. No authentication
Correct Answer: ABD

Section: (none)
Explanation
Explanation/Reference:
QUESTION 2
Refer to the configuration output. RTA has been configured using AAA as shown, and associated with the “huawei” domain. For users in the huawei domain, which
authentication-scheme will be used?
A. au1
B. au2
C. au1 will be used. When au1 is deleted, users will use au2
D. au2 will be used. When au2 is deleted, users will use au1
Correct Answer: B
885CB989129A5F974833949052CFB2F2
Section: (none)
Explanation
QUESTION 3
A user accesses a server supporting AAA, for which the authorization mode on the AAA server has been configured using the command “authorization-mode
hwtacacs if-authenticated”.
Which of the following statements regarding this command are true? (Choose three).
A. If the hwtacacs server fails to respond, the user will be authenticated using local authentication.
B. If the hwtacacs server fails to respond, the user will be authenticated using remote authentication.
C. If the hwtacacs server fails to respond, the user will bypass authentication.
D. The hwtacacs server will authorize the user.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 4
Which of the following descriptions regarding eSight is not correct?
A. eSight is used to monitor and manage enterprise networks.

B. eSight supports only Huawei devices.
C. eSight supports WLAN management and monitoring of hotspot coverage.
D. eSight supports the backup of configuration files and network traffic analysis.
Correct Answer: B
Section: (none)
Explanation
QUESTION 5
885CB989129A5F974833949052CFB2F2
Which of the following parameters is not used by Advanced ACL?
A. Source interface
B. Destination port number
C. Protocol number
D. Time-range
Correct Answer: A
Section: (none)
Explanation
QUESTION 6
Refer to the configuration output. Which of the following statements regarding ACL 2001 is correct?
A. Packets from network 10.0.1.0/24 network will be denied.

B. Packets from network 10.0.1.0/24 network will be permitted.
C. Packets destined for network 10.0.1.0/24 will be denied.
D. Packets destined for network 10.0.1.0/24 will be permitted.
Correct Answer: B
Section: (none)
Explanation
QUESTION 7
Refer to the configuration output. Which of the following statements is correct regarding the configuration of the ACL on RTA?
885CB989129A5F974833949052CFB2F2
A. Packets from network 20.1.1.0/24 network will be denied.
B. Packets from network 20.1.1.0/24 network will be permitted.
C. Packets destined for network 20.1.1.0/24 will be denied.
D. Packets destined for network 20.1.1.0/24 will be permitted.
Correct Answer: A
Section: (none)
Explanation
QUESTION 8
Refer to the configuration output. Which of the following statements are correct regarding the configuration of the ACL on RTA? (Choose two).
A. Packets from network 172.16.1.1/32 will be denied.

B. Packets from network 172.16.1.0/24 will be denied.
C. Packets from network 172.17.1.0/24 will be denied.
D. Packets from network 172.18.0.0/16 will be denied.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 9
The network administrator wants to improve the performance of network transmission, what steps can the administrator take? (Choose two)
885CB989129A5F974833949052CFB2F2
A. Change the work mode to full duplex of each end station.
B. Link the end stations together using a switch.
C. Change the work mode to half duplex of each end station.
D. Link the end stations together using a hub.
Correct Answer: AB
Section: (none)
Explanation
QUESTION 10
The network administrator wishes to transmit data between two end stations. The network interface cards of both devices operates at 100Mbps however one
supports half duplex while the other uses full duplex mode.
What will occur as a result?
A. The end stations cannot communicate.

B. The end stations can communicate, but data may be lost during transmission of large amounts of traffic.
C. The end stations will operate normally
D. The end stations can communicate, but speed is different during transmission of large amounts of traffic.
Correct Answer: B
Section: (none)
885CB989129A5F974833949052CFB2F2
Explanation
QUESTION 11
While inspecting packets in the network, a network administrator discovers a frame with the destination MAC address of 01-00-5E-A0-B1-C3.
What can the administrator determine from this?
A. The MAC address is a unicast address.

B. The MAC address is a broadcast address
C. The MAC address is a multicast address.
D. The MAC address is incorrect.
Correct Answer: C
Section: (none)
Explanation
QUESTION 12
According to OSI reference model, which layer is responsible for end to end error checking and flow control?
A. Physical layer
B. Data link layer
C. Network layer
D. Transport layer
Correct Answer: D
Section: (none)
Explanation
QUESTION 13
Which of the following mechanisms are used for flow control? (Choose three)
885CB989129A5F974833949052CFB2F2
A. Acknowledgement
B. Buffering
C. Source quench messages
D. Windowing
Correct Answer: BCD

Section: (none)
Explanation
QUESTION 14
An Ethernet frame is captured by wireshark and the value of Type/Length field is 0x0800.
Which of the following statements about the frame are correct? (Choose two)
A. The frame format is Ethernet_II

B. The frame format is IEEE802.3
C. Its upper layer protocol is IP
D. Its upper layer protocol is IPX
Correct Answer: AC
Section: (none)
Explanation
QUESTION 15
Which of the following descriptions regarding the TTL field of the IP packet is correct?
A. The TTL defines how many packets the source can send.
B. The TTL defines the duration during which the source can send packets.
C. The TTL value will decrement by 1 each time the packet is routed.
D. The TTL value will increment by 1 each time the packet is routed.
Correct Answer: C
Section: (none)
885CB989129A5F974833949052CFB2F2
Explanation
QUESTION 16
Which of the following statements are correct about TTL field in IP packet? (Choose two)
A. The maximum value of TTL is 65535.

B. Normally, it's impossible for a router to receive a packet whose TTL is zero.
C. The main purpose of TTL is to prevent IP packets from circulating endlessly in a network which can consume a lot of bandwidth.
D. TTL value will be decremented as a packet is passed through the network devices such as hub, LAN switch and router.
Correct Answer: BC
Section: (none)
Explanation
QUESTION 17
To provide the information about the IP addresses that a user packet traverses along the path to the destination, which of the following does Tracert record in each
expired ICMP TTL packet?
A. Destination port
B. Source port
C. Destination IP address
D. Source IP address
Correct Answer: D
Section: (none)
Explanation
QUESTION 18
A network administrator recently used tracert to trace the path to the destination IP address of an external website, however the trace path displayed only a timeout
result.
885CB989129A5F974833949052CFB2F2
Which of the following statements correctly explains the reason for this? (Choose two)
A. The source router had shutdown the ICMP function.

B. This destination IP address does not exist.
C. The gateway cannot find a route to the destination.
D. This is a normal phenomenon.
Correct Answer: BC
Section: (none)
Explanation
QUESTION 19
A network administrator uses the ping command to test connectivity to the destination 10.0.0.2 on a Huawei AR series router.
Which statement regarding the output is correct?
A. The network administrator used the command ping -c 2 -s 800 10.0.0.2

B. The network administrator used the command ping -a 2 -v 800 10.0.0.2
C. The path between the source and destination is not OK.
D. The network administrator changed the default TTL value.
Correct Answer: A
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 20
An ARP request is sent by host A to obtain the destination MAC address of host D.
Which statement is true about regarding the ARP reply?
A. The destination MAC address of this frame is the MAC address of Switch A.
B. The destination IP address of this packet is the VLANIF1 IP address of Switch A.
C. The destination MAC address of this frame is the MAC address of Host A.
D. The destination IP address of this packet is a broadcast IP address.
Correct Answer: C
Section: (none)
Explanation
QUESTION 21
How many probe packets are sent for each TTL value by default when "tracert" is used to detect the path along which packet is sent from source to destination?
A. 3
B. 4
C. 6
D. 8
Correct Answer: A
Section: (none)
Explanation
QUESTION 22
A router functioning as a Proxy receives an ARP request packet, but finds that the destination address in the packet is not intended for itself. In this case, what will
the router do? (Choose two)
A. Discard the packet.

B. Check for a route that matches the destination address.
C. Forward its MAC address to the ARP request sender after finding that a route to the destination address is available.
885CB989129A5F974833949052CFB2F2
D. Broadcast the ARP request packet.
Correct Answer: BC
Section: (none)
Explanation
QUESTION 23
What will the destination MAC address be at the moment a frame is transmitted by the host, when the router is the IP destination?
A. The MAC address of the switch.

B. The MAC address of the router interface G0/0/0.
C. The MAC address of the host.
D. The destination MAC address will be a broadcast MAC address.
Correct Answer: D
Section: (none)
Explanation
QUESTION 24
Which of the following statements about gratuitous ARP packets are true? (Choose two)
A. A system can determine whether conflicting IP addresses are used by sending a gratuitous ARP packet
B. A gratuitous ARP packet uses the same format as an ARP request packet.
C. A gratuitous ARP packet can help to update an IP address.
D. A gratuitous ARP packet uses the same format as an ARP reply packet.
Correct Answer: AB
Section: (none)
Explanation
QUESTION 25
885CB989129A5F974833949052CFB2F2
UDP is connectionless oriented, which of the following must be used in order to ensure reliability?
A. Internet Protocol
B. Application Layer Protocol
C. Network Layer Protocol
D. Transmission Control Protocol
Correct Answer: B
Section: (none)
Explanation
QUESTION 26
Refer to the graphic.
The administrator has configured an IP address for Host A and Host B, but had forgotten to configure a default gateway.
What effect will this have on the hosts?
A. Neither host will be affected, and therefore will be able to communicate with the peer.
B. Host A will be unable to connect to the router’s G0/0/0 interface.
C. Hosts will be unable to communicate unless arp-proxy is enabled on the router.
D. The host will be unable to reach neither the local nor remote network destinations.
Correct Answer: C
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 27
The administrator uses the ping command on the host to test connectivity to the website www.huawei.com.
The command line shows a request time out. The administrator displays the ARP entries for the host.
Which entry will be found in the ARP cache table of the host?
A. The MAC address of the destination www.huawei.com will exist in the ARP cache.
B. The MAC address of the switch will exist in the ARP cache.
C. The IP address of the destination www.huawei.com will exist in the ARP cache.
D. The MAC address of router interface G0/0/0, will exist in the ARP cache.
Correct Answer: D
Section: (none)
Explanation
QUESTION 28
When R2 forwards data to R3 from R1, which of the following items will change? (Choose two)
A. The source MAC address

B. The destination MAC address
C. The source IP address
D. The destination IP address
Correct Answer: AB
Section: (none)
Explanation
QUESTION 29
If Host B also configured the IP address as “192.168.1.1/24”, an IP address config will occur.
885CB989129A5F974833949052CFB2F2
What will happen as a result?
A. Host B will send an ICMP request to the destination with the configured IP address. If a reply is received, the host will notify of an address conflict.
B. Host A will send a gratuitous ARP request to resolve the MAC address of the destination 192.168.1.1, for which Host B will reply.
C. Host B will send a gratuitous ARP request to resolve the MAC address of the destination 192.168.1.1, for which Host A will reply.
D. Host A will ignore any received ARP request intended for destination 192.168.1.1.
Correct Answer: C
Section: (none)
Explanation
QUESTION 30
An administrator connects two switches together in a local enterprise network. The ports of one switch support Fast Ethernet, while the ports of the other switch
support Gigabit Ethernet. Hosts connected to one switch are able to communicate, however communication between the two switches fails.
What is the possible reason for this?
A. The ports have disabled auto-negotiation.

B. One port is supporting auto-negotiation, while auto-negotiation is disabled on the port of the other switch.
C. The port of one switch is operating using half duplex mode, while the port of the other switch is using full duplex mode.
D. A Fast Ethernet port cannot communicate directly with a Gigabit Ethernet port.
Correct Answer: A
Section: (none)
Explanation
QUESTION 31
A layer 2 LAN switch generates CAM table entries according to the ( ) of the received frame.
A. Source MAC address

B. Destination MAC address
C. Source IP address
D. Destination IP address
885CB989129A5F974833949052CFB2F2
Correct Answer: A
Section: (none)
Explanation
QUESTION 32
Which of the following statements regarding layer-2 switch is incorrect?
A. The switch learns MAC addresses automatically.

B. The layer-3 header is modified before the received packet is transmitted.
C. The layer-2 header is modified before the received packet is transmitted.
D. The layer-2 LAN switch operates at data link layer.
Correct Answer: B
Section: (none)
Explanation
QUESTION 33
Which of the following are routed protocols? (Choose all that apply.)
A. IP
B. OSPF
C. BGP
D. IPX
Correct Answer: AD
Section: (none)
Explanation
QUESTION 34
Which of the following statements regarding the routing table are correct? (Choose all that apply.)
885CB989129A5F974833949052CFB2F2
A. The next hop in the routing table is redundant because the outgoing interface can be used for packet forwarding.
B. The routes from generated by different protocols have different preferences.
C. The metrics of different routing protocols are comparable.
D. The metrics of different routing protocols are not comparable
Correct Answer: BD
Section: (none)
Explanation
QUESTION 35
Which of the following commands can be used to display the routing table on a Quidway router?
A. display ip path
B. display ip routing-table
C. display interface
D. display current-configuration
Correct Answer: B
Section: (none)
Explanation
QUESTION 36
The administrator cannot use telnet to manage the AR2200. The administrator is able to verify connectivity to the router and has been informed that other
administrators have no difficulties using telnet.
Which statements describe the possible reasons for this problem? (Choose all that apply.)
A. The user’s status has been blocked

B. The user’s privilege level has been changed to 0.
C. The user has been deleted.
D. The telnet service in the AR2200 router has been disabled.
885CB989129A5F974833949052CFB2F2
Correct Answer: AC
Section: (none)
Explanation
QUESTION 37
The users who log on the router through Telnet are not permitted to configure IP address.
What is the possible reason?
A. Communication failures occur between the user and the router.

B. The authentication mode of Telnet is set incorrectly.
C. Privilege level of Telnet is set incorrectly.
D. SNMP parameters are set incorrectly.
Correct Answer: C
Section: (none)
Explanation
QUESTION 38
On the interface serial 1/0/1 of RTA, the command “ip address unnumbered interface loopback 0” has been configured.
Which following statements are correct? (Choose two).
A. The IP address of interface serial 1/0/1 is 10.1.1.1/24

B. The IP address of interface serial 1/0/1 is 10.1.1.1/32
C. The route entry 10.1.1.0/24 exists in RTA’s routing-table
885CB989129A5F974833949052CFB2F2
D. The route entry 10.1.1.0/24 does not exist in RTA’s routing-table
Correct Answer: BD
Section: (none)
Explanation
QUESTION 39
The host has a problem establishing a telnet connection with the router attached to interface G0/0/0. Which of the following steps can be used to help the
administrator identify the problem? (Choose two)
A. Check whether the host has configured the gateway IP address.

B. Check whether the switch has configured the gateway IP address.
C. Use the ping tool to check connectivity between host and router.
D. Check the telnet server configuration is right on the router.
Correct Answer: CD
885CB989129A5F974833949052CFB2F2
Section: (none)
Explanation
QUESTION 40
Which of the following methods are supported by VRP platform to configure the router? (Choose three)
A. Through the Console port

B. Through Telnet
C. Through the AUX port
D. Through FTP
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 41
The administrator wishes to update the configuration file of an AR2200 router using a USB cable.
How can this be achieved? (Choose all that apply.)
A. The administrator should connect the USB cable between the terminal and the mini USB port of the AR2200 router.
B. The administrator should connect the USB cable between the terminal and the USB port of the AR2200 router.
C. The AR2200 router cannot support configuration updates through a USB cable.
D. The administrator should install the mini USB drivers on the terminal after connecting the USB.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 42
Whilst configuring a device, an administrator experiences trouble remembering certain commands.
885CB989129A5F974833949052CFB2F2
Which of the following will help support the administrator? (Choose two)
A. TAB
B. question mark
C. ctrl+b
D. ctrl+c
Correct Answer: AB
Section: (none)
Explanation
QUESTION 43
Which of the following is abbreviation of VRP?
A. Versatile Routine Platform

B. Virtual Routing Platform
C. Virtual Routing Plane
D. Versatile Routing Platform
Correct Answer: D
Section: (none)
Explanation
QUESTION 44
Which of the following must be used to establish the configuration environment when a router is powered on for the first time?
A. SSL
B. SSH
C. Console port
D. Telnet
Correct Answer: C
885CB989129A5F974833949052CFB2F2
Section: (none)
Explanation
QUESTION 45
Which of the following parameter settings for terminal emulation are correct when configuring a Huawei router through the Console port?
A. 4800bps, 8 data bits,1 stop bits, odd parity check, and no flow control
B. 9600bps, 8 data bits, 1 stop bits, no parity check, and no flow control
C. 9600bps, 8 data bits, 1 stop bits, even parity check, and hardware flow control
D. 19200bps, 8 data bits, 1 stop bits, no parity check, and no flow control
Correct Answer: B
Section: (none)
Explanation
QUESTION 46
Which of the following commands is used to enter the system-view from the user view on a Huawei router?
A. system-view
B. enable
C. configure terminal
D. interface system
Correct Answer: A
Section: (none)
Explanation
QUESTION 47
On Huawei VRP platform, which of the following can be used to invoke the history command saved by the command line interface? (Choose two)
A. Up cursor key < >
885CB989129A5F974833949052CFB2F2
B. Left cursor key < >
C. Ctrl+P
D. Ctrl+U
Correct Answer: AC
Section: (none)
Explanation
QUESTION 48
The administrator wishes to change name of the router. Under which view should the administrator be in order to achieve this?
A. User-view
B. System-view
C. Interface-view
D. Protocol-view
Correct Answer: B
Section: (none)
Explanation
QUESTION 49
Which of the following commands can switch a view from the system view to the user view?
A. System-view
B. Router
C. Quit
D. User-view
Correct Answer: C
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 50
<Huawei>
Warning: Auto-Config is working. Before configuring the device, stop Auto-Config. If you perform configurations when Auto-Config is running, the DHCP, routing,
DNS, and VTY configurations will be lost. Do you want to stop Auto-Config? [y/n]:
When an administrator first initializes the router, a warning is displayed. Which statement regarding this warning is correct?
A. If Auto-Config is required, the administrator should select ‘y’.

B. If Auto-Config is not required, the administrator should select ‘n’, for which subsequent configuration of the DHCP server, routing, DNS server and VTY user
configuration is lost.
C. When a device is started for the first time, the Auto-Config function is active.
D. When a device is started for the first time, the Auto-Config function is inactive.
Correct Answer: C
Section: (none)
Explanation
QUESTION 51
An AR2200 router in the company network cannot boot. In order to resolve this, the administrator wishes to update the VRP software.
What should he/she do?
A. The administrator should use a console cable to connect the router and host, and directly upgrade the device.
B. The administrator should use FTP to transfer the VRP software, by configuring the AR2200 router as an FTP client.
C. The administrator should use DHCP to boot the AR2200, and then use the AR2200 router as a TFTP client to download the VRP software from the server.
D. The administrator should use the telnet command on the client to remote access the device, and upgrade the VRP software.
Correct Answer: B
Section: (none)
Explanation
QUESTION 52
885CB989129A5F974833949052CFB2F2
An end system is unable to communicate with a DHCP server following the startup process.
Which IP address may be used by the client?
A. 0.0.0.0
B. 127.0.0.1
C. 169.254.2.33
D. 255.255.255.255
Correct Answer: C
Section: (none)
Explanation
QUESTION 53
Refer to the configuration output. The administrator wishes to configure the DHCP server pool in order to assign an IP address to the customer’s terminal device.
Which command should be included in the configuration to provide the minimal lease period for IP addresses?
A. dhcp select relay

B. lease day 1
C. lease 24
D. lease 0
Correct Answer: B
Section: (none)
Explanation
QUESTION 54
A DHCP server in the enterprise network is being used to allocated IP addresses to hosts. An administrator discovers however that some hosts are obtaining IP
885CB989129A5F974833949052CFB2F2
addresses outside of the scope of the DHCP server’s address pool.
What are the possible reasons for this? (Choose three).
A. Another DHCP server exists in the network and is allocating IP addresses to hosts that happen to be within a closer proximity than the authorized DHCP server.
B. The hosts were unable to discover a DHCP server and therefore generated their own address in the 169.254.0.0 address range.
C. The hosts were unable to discover a DHCP server and therefore generated their own address in the 127.254.0.0 address range.
D. All addresses from the DHCP pool have been assigned.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 55
Refer to the configuration output. Following configuration, a host is connected to the interface Gigabit Ethernet 0/0/1 of the router. Which IP address will the client
obtain?
A. An IP address from network 10.10.10.0/24 will be assigned.

B. An IP address from network 10.20.20.0/24 will be assigned.
C. The host will be unable to obtain an IP address.
D. An IP address may be assigned from either 10.10.10.0/24 or 10.20.20.0/24.
Correct Answer: A
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 56
The IP addresses of clients in the network are deployed via a DHCP server. When a host reboots, which message will the host first send to the DHCP server?
A. DHCP DISCOVER
B. DHCP REQUEST
C. DHCP OFFER
D. DHCP ACK
Correct Answer: B
Section: (none)
Explanation
QUESTION 57
A DHCP Unique Identifier (DUID) in DHCPv6 can be configured in VRP using which formats? (Choose two).
A. DUID-LL
B. DUID-LLT
C. DUID-EN
D. DUID-LLC
Correct Answer: AB
Section: (none)
Explanation
QUESTION 58
What is the default authentication mode for the default_admin domain?
A. None
B. Local
885CB989129A5F974833949052CFB2F2
C. Radius
D. 802.1X
Correct Answer: B
Section: (none)
Explanation
QUESTION 59
How many domains can be configured on a Huawei router?
A. 30
B. 31
C. 32
D. 33
Correct Answer: A
Section: (none)
Explanation
QUESTION 60
An authenticator router has been configured with two domains named “Area1” and “Area2”, following which a user is created with the username “huawei” and the
password ”hello” for authentication. Which domain does this user belongs to?
A. Area1 domain
B. Area2 domain
C. default domain
D. default_admin domain
Correct Answer: C
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 61
Which of the following protocols is used in Frame Relay to map the address to DLCI dynamically?
A. ARP protocol
B. RARP protocol
C. InARP protocol
D. Map protocol
Correct Answer: C
Section: (none)
Explanation
QUESTION 62
Which of the following parameters must be specified when configuring static mapping for Frame Relay network? (Choose two)
A. Local DLCI
B. Remote DLCI
C. Local network layer protocol address
D. Remote network layer protocol address
Correct Answer: AD
Section: (none)
Explanation
QUESTION 63
Which of the following regarding Frame Relay DLCI are correct? (Choose three)
A. DLCI is locally significant

B. DLCI is allocated by DTE
C. The range of DLCI value that can be used is from 16-1007
D. The same DLCI can be configured on different physical interfaces
885CB989129A5F974833949052CFB2F2
Correct Answer: ACD
Section: (none)
Explanation
QUESTION 64
What is the meaning of 200 in the command "fr map ip 10.1.1.2 200"?
A. remote logical channel ID

B. local DLCI
C. remote interface ID
D. remote node ID
Correct Answer: B
Section: (none)
Explanation
QUESTION 65
Which of the following commands can be used to display mapping relationship between network address and DLCI?
A. display fr interface
B. display fr
C. display fr map-info
D. display fr brief
Correct Answer: C
Section: (none)
Explanation
QUESTION 66
Which of following may be the reasons that cause Frame Relay PVC to work abnormally? (Choose three)
885CB989129A5F974833949052CFB2F2
A. Same DLCI number is configured on the same router
B. LMI type mismatch
C. Frame Relay encapsulation type mismatch
D. Incorrect configuration of the DLCI number
Correct Answer: BCD

Section: (none)
Explanation
QUESTION 67
An administrator wishes to update the VRP software of company’s AR2200 router. How can this be achieved? (Choose three)
A. The administrator can use FTP to transfer the VRP software, with the AR2200 router as the FTP client.
B. The administrator can use FTP to transfer the VRP software, with the AR2200 router as the FTP server.
C. The administrator can use TFTP to transfer the VRP software, with the AR2200 router as the TFTP server.
D. The administrator can use TFTP to transfer the VRP software, with the AR2200 router as the TFTP client.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 68
An administrator wishes to implement new features in the network, but the VRP version of one AR2200 router is out of date. The administrator needs to upgrade the
VRP software.
Which of the following options regarding file transfer is false?
A. The AR2200 router can function as a TFTP client to support the upgrade.
B. The AR2200 router can function as the TFTP server to support the upgrade.
C. The AR2200 router can function as the FTP server to support the upgrade.
D. The AR2200 router can function as an FTP client to support the upgrade.
885CB989129A5F974833949052CFB2F2
Correct Answer: B
Section: (none)
Explanation
QUESTION 69
FTP and TFTP can be used to update the system file on Huawei routers. Which of the following statements are correct? (Choose three)
A. Huawei router can be configured as FTP Client

B. Huawei router can be configured as FTP Server
C. Huawei router can be configured as TFTP Client
D. Huawei router can be configured as TFTP Server
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 70
Which of the following formats represent an accurate condensing of the IPv6 address 2031:0000:720C:0000:0000:09E0:839A:130B? (Choose two).
A. 2031:0:720C:0:0:9E0:839A:130B
B. 2031:0:720C:0:0:9E:839A:130B
C. 2031::720C::9E0:839A:130B
D. 2031:0:720C::9E0:839A:130B
Correct Answer: AD
Section: (none)
Explanation
QUESTION 71
Which of the following IPv6 addresses can be configured on a router’s interface? (Choose two).
885CB989129A5F974833949052CFB2F2
A. fe80:13dc::1/64
B. ff00:8a3c::9b/64
C. ::1/128
D. 2001:12e3:1b02::21/64
Correct Answer: AD
Section: (none)
Explanation
QUESTION 72
The IPv6 address architecture does not include which of the following address types?
A. unicast
B. multicast
C. broadcast
D. anycast
Correct Answer: C
Section: (none)
Explanation
QUESTION 73
In a small network supporting IPv6, a network administrator wishes implement RIPng.
Which of the following commands should be used to enable this protocol?
A. [RTA-GigabitEthernet0/0/0]ripng 1 enable
B. [RTA]ripng 1 enable
C. <RTA>ripng 1 enable
D. [RTA-ripng-1]ripng 1 enable
Correct Answer: A
Section: (none)
885CB989129A5F974833949052CFB2F2
Explanation
QUESTION 74
In a network supporting IPv6, OSPF no longer supports which feature?
A. multiple areas
B. Router-ID
C. authentication
D. multicast updates
Correct Answer: C
Section: (none)
Explanation
QUESTION 75
The network administrator has decided to configure link aggregation in the enterprise network.
Which of the following represent advantages of link aggregation? (Choose three)
A. Load balancing.
B. Improved bandwidth.
C. Enhanced reliability.
D. Improved security.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 76
What is the maximum number of member interfaces supported by a single Eth-Trunk?
885CB989129A5F974833949052CFB2F2
A. 6
B. 8
C. 10
D. 12
Correct Answer: B
Section: (none)
Explanation
QUESTION 77
In Layer 2 mode, the transmission rate of an Eth-Trunk interface is determined by which of the following? (Choose all that apply.)
A. Maximum number of Up member links

B. Minimum number of Up member links
C. Number of Up member interfaces
D. Number of interfaces.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 78
The network administrator wishes to forward data over an Eth-trunk, however associated member interfaces operate at different rates. In terms of the resulting
behavior, which of the following is true?
A. The two switches will not be able to communicate.

B. The higher rate member interfaces may incur packet loss.
C. The Eth-Trunk will work normally.
D. The lower rate member interfaces may incur packet loss.
Correct Answer: D
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 79
A network requires a solution to allow 50 private IP addresses to be translated, however only a single public address is available for use.
Which translation method can be used to support this requirement?
A. Static NAT
B. Dynamic NAT
C. Easy-IP
D. NAPT
Correct Answer: C
Section: (none)
Explanation
QUESTION 80
A web server in a private network is required to provide HTTP services to public users. The network administrator is required to configure NAT on RTA.
Which configuration should be used?
A. [RTA-Serial1/0/1]nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080
B. [RTA-Serial0/0/1]nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080
C. [RTA-Gigabitethernet0/0/1]nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080
D. [RTA- Gigabitethernet0/0/1]nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080
885CB989129A5F974833949052CFB2F2
Correct Answer: A
Section: (none)
Explanation
QUESTION 81
The network administrator needs to configure static NAT on RTA, in order to allow Host A to communicate with Host C.
Which command is correct?
A. [RTA-Serial1/0/1]nat outbound 200.1.1.10

B. [RTA-Serial1/0/1]nat static global 200.1.1.10 inside 192.168.1.0
C. [RTA-Serial1/0/1]nat static global 192.168.1.1 inside 200.1.1.10
D. [RTA-Serial1/0/1]nat static global 200.1.1.10 inside 192.168.1.1
Correct Answer: D
Section: (none)
Explanation
QUESTION 82
[RTA-GigabitEthernet0/0/0]nat outbound 2000 address-group 1
885CB989129A5F974833949052CFB2F2
Refer to the configuration output. What does the value “2000” refer to?
A. It represents the ACL number.

B. It represents the NAT number.
C. It represents the translated port number.
D. It represents the number of bytes that can be translated before the address is returned to the public address pool.
Correct Answer: A
Section: (none)
Explanation
QUESTION 83
NAPT uses the same public address but different port numbers to translate private addresses.
Which statement regarding the port number is correct?
A. It is necessary to configure port number mapping manually.

B. It is only necessary to configure the port number range.
C. It is not necessary to configure port numbers.
D. An access control list is needed to assign port numbers.
Correct Answer: C
Section: (none)
Explanation
QUESTION 84
A configured internal host of a private network wishes to access the internet. What must be configured on the enterprise network egress router in order to achieve
this? (Choose all that apply.)
A. NAT Easy IP
B. DHCP
C. BGP
885CB989129A5F974833949052CFB2F2
D. Default route
Correct Answer: AD
Section: (none)
Explanation
QUESTION 85
Which of the following statements are correct about NAT? (Choose three)
A. NAT is the abbreviation for "Network Address Translation".

B. NAT is used for translation between private and public network addresss.
C. When hosts inside a private network access the outside network, NAT is not required.
D. NAT provides an effective way to solve the problem of insufficient IP addresses.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 86
Which of the following statements about a designated port working in RIPv2 multicast mode are true? (Choose three)
A. The port receives only RIPv2 multicast packets.

B. The port does not receive RIPv1 broadcast packets.
C. The port does not receive RIPv2 broadcast packets.
D. The port receives only RIPv1 multicast packets.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 87
885CB989129A5F974833949052CFB2F2
Which of the following statements regarding the router ID in OSPF are incorrect? (Choose three)
A. The router IDs of OSPF routers in the same area must be the same, but can be different in different areas.
B. The router ID must be the IP address of an OSPF router interface.
C. The router ID must be configured manually.
D. A router running OSPF must have a router ID for it to operate properly.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 88
Which of the following statements regarding Designated Routers in OSPF are correct? (Choose three)
A. DR is elected by all the routers in the same network segment.

B. If the priorities of two routers are different, the router with the lower priority will be elected as DR.
C. If the priorities of two routers are equal, the router with the higher Router ID will be elected as DR.
D. DR and BDR must be adjacent.
Correct Answer: ACD

Section: (none)
Explanation
QUESTION 89
On the VRP platform, which of the following commands is used to configure the Router ID of a router as 1.1.1.1?
A. <Huawei>router id 1.1.1.1
B. [Huawei]router id 1.1.1.1
C. [Huawei]router-id 1.1.1.1
D. [Huawei]router id 1.1.1.1 255.255.255.255
Correct Answer: B
Section: (none)
885CB989129A5F974833949052CFB2F2
Explanation
QUESTION 90
The administrator wishes to configure OSPF on a router in the network however the router has no loopback interface.
Which value will be used as the router ID?
A. The lowest IP address of the router’s active interfaces.

B. The highest IP address of the router’s active interfaces.
C. The IP address of the management interface.
D. The priority value of the router.
Correct Answer: B
Section: (none)
Explanation
QUESTION 91
Which of the following statements regarding single area OSPF are correct? (Choose three)
A. An IP address needs to be configured on a loopback interface of each router before configuring an OSPF area.
B. The value of an area can be from 0.0.0.0 to 255.255.255.255.
C. A single area can be configured using any supported area number.
D. All of the links of the network need to be advertised in Area 0.
Correct Answer: BCD

Section: (none)
Explanation
QUESTION 92
10.0.1.0/24 O_ASE 150 2 D 10.0.23.3 Serial2/0/0
885CB989129A5F974833949052CFB2F2
Refer to the display output. Which of the following statements regarding route shown are true? (Choose two)
A. The address 10.0.23.3 has been configured on the peer’s serial 2/0/0 interface.
B. The route preference has been changed by the administrator.
C. The metric for the route 10.0.1.0 indicates that two hops are needed.
D. The route has been learned via the OSPF protocol.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 93
Which of the following statements regarding the DR in an OSPF network are correct? (Choose two)
A. There must be at least one DR in an OSPF area.

B. A DR must be elected among the routers through the negotiations that are defined by OSPF protocol.
C. Only the router with highest priority will be elected as DR.
D. Only NBMA or Broadcast networks need to elect DR.
Correct Answer: BD
Section: (none)
Explanation
QUESTION 94
Which of the following statements about router IDs are true? (Choose two)
A. The routers contained in the same LSDB have the same router ID.
B. Each router in an OSPF network must have a unique router ID.
C. Two routers in different OSPF areas can have the same router ID.
D. A router ID is expressed in a 32-bit dotted decimal format.
Correct Answer: BD
Section: (none)
885CB989129A5F974833949052CFB2F2
Explanation
QUESTION 95
In a network supporting IPv6, OSPF no longer supports which feature?
A. multiple areas
B. Router-ID
C. authentication
D. multicast updates
Correct Answer: C
Section: (none)
Explanation
QUESTION 96
Two routers are configured with OSPFv3. OSPFv3 is enabled on all interfaces of each router.
Which of the following is true in the event that the network administrator does not configure a Router-ID?
A. The IP address of the loopback 0 interface will be used as the router ID.
B. The IP address of the loopback 1 interface will be used as the router ID.
C. The IP address of interface G0/0/0 will be used as the router ID.
D. No router ID will be assigned to the router.
Correct Answer: D
Section: (none)
Explanation
QUESTION 97
According to the default value of route preference on the VRP platform, which of the following represent the correct sequence for direct route, static route, RIP and
OSPF if they are listed from high preference to low preference?
885CB989129A5F974833949052CFB2F2
A. Direct, Static, RIP, OSPF
B. Direct, OSPF, Static, RIP
C. Direct, OSPF, RIP, Static
D. Direct, RIP, Static, OSPF
Correct Answer: B
Section: (none)
Explanation
QUESTION 98
A router has learned two routes for the same network with the same prefix. One route has been learned via OSPF with a metric of 4882, while the other route has
been learned via RIPv2 with a metric of 4.
Which route (s) will be found in the routing table?
A. The RIPv2 route.

B. The OSPF and RIPv2 routes.
C. The OSPF route.
D. Neither of these routes will be found in the routing table.
Correct Answer: C
Section: (none)
Explanation
QUESTION 99
After checking the OSPF neighbor state, the administrator discovers that the router has established a TWOWAY state with the peering router.
What can be understood from this information? (Choose two)
A. The routers are configured using the same process ID

B. The routers are configured using the same area ID
C. The routers are configured using wrong router ID
885CB989129A5F974833949052CFB2F2
D. The routers are considered DROthers in a broadcast network
Correct Answer: CD
Section: (none)
Explanation
QUESTION 100
Two routers are connected via serial interfaces, for which the link-protocol is PPP. The network administrator wishes to configure PPP authentication to improve
security on this link.
Which PPP authentication method provides a more secure solution?
A. CHAP
B. PAP
C. MD5
D. SSH
Correct Answer: A
Section: (none)
Explanation
QUESTION 101
If PPP authentication fails, which type of packet will be sent to the authenticated peer by the authenticator?
A. Authenticate-Ack
B. Authenticate-Nak
C. Authenticate-Reject
D. Authenticate-Reply
Correct Answer: B
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 102
PPP is more secure than HDLC because PPP supports authentication protocols such as ( ). (Choose two)
A. PAP
B. MD5
C. CHAP
D. SSH
Correct Answer: AC
Section: (none)
Explanation
QUESTION 103
When both ends running PPP protocol detect that the physical link is active, the link state will transit from dead to establish.
Which of the following protocols is used to negotiate the link parameters during this phase?
A. IP
B. DHCP
C. LCP
D. NCP
Correct Answer: C
Section: (none)
Explanation
QUESTION 104
A serial interface of a Huawei router currently using HDLC needs to assign PPP as the encapsulation protocol.
Which of the following commands is required to be configured at the serial interface view?
A. link-protocol ppp
885CB989129A5F974833949052CFB2F2
B. encapsulation ppp
C. enable ppp
D. address ppp
Correct Answer: A
Section: (none)
Explanation
QUESTION 105
When configuring the PPP authentication method as PAP, which of the following operations are necessary? (Choose three)
A. Add the user name and password of the authenticated party to the local user list.
B. Configure the encapsulation type of the interface connected to the peer as PPP.
C. Configure PPP authentication method as CHAP.
D. On the authenticated party end, configure the user name and password that are sent to authenticator.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 106
Two routers have established a point-to-point network using PPP. The administrator has configured the routers to run OSPF in the same area with the same router
ID, what behavior will occur as a result of the configuration?
A. The routers will build a neighbor relationship even though both routers are using the same router ID.
B. VRP will notify of a router ID conflict between the two routers.
C. The routers will build an adjacency even though both routers are using the same router ID.
D. The routers will not send hello packets to each other because they are using the same router ID.
Correct Answer: B
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 107
When configuring a router as a PPPoE client, which configuration is not necessary?
A. Configuration of the dialer-rule

B. Configuration of the dialer interface
C. Configuration of an IP address on the dialer interface
D. Configuration of a password on the dialer interface
Correct Answer: C
Section: (none)
Explanation
QUESTION 108
In the PPPoE discovery stage, the PPPoE server assigns a session-id to the PPPoE client in which packet?
A. PADI
B. PADO
C. PADR
D. PADS
Correct Answer: D
Section: (none)
Explanation
QUESTION 109
[Huawei]rip 1
[Huawei-rip-1]version 2
Refer to the command output. An administrator wishes to configure RIP. Which other command needs to configured for RIP routes to be advertised?
A. import-route GigabitEthernet 0/0/1
885CB989129A5F974833949052CFB2F2
B. network 192.168.1.0 0.0.0.255
C. network GigabitEthernet 0/0/1
D. network 192.168.1.0
Correct Answer: D
Section: (none)
Explanation
QUESTION 110
A user can view the information for the RIP protocol on a router. What does “Age time” in the returned result of the command mean?
A. The interval of updating an RIP packet

B. The aging time of an RIP route
C. The suppression time of an RIP route
D. The time spent on switching between RIP routes
Correct Answer: B
Section: (none)
Explanation
QUESTION 111
Refer to the debug output. Following configuration of R2, the administrator discovers that the behavior is not as expected and performs debugging. Based on the
885CB989129A5F974833949052CFB2F2
output from the debug, what is the source of the problem?
A. R2 has configured an ACL to block the route to network 1.0.0.0

B. R2 has enabled split horizon.
C. R1 is using authentication, however R2 is not.
D. R2 is operating using RIPv2, while R1 is using RIPv1.
Correct Answer: D
Section: (none)
Explanation
QUESTION 112
When a network administrator configures STP in the network, BPDU begin to be sent by switch. Which of the following statements regarding the BPDU frame are
correct?
A. A BPDU uses the IEEE 802.3 standard frame type

B. A BPDU uses the Ethernet II standard frame type
C. The BPDU frame’s control field is 3
D. The destination MAC address field of a BPDU frame is a broadcast address
Correct Answer: A
Section: (none)
Explanation
QUESTION 113
In the case of Huawei router, the Tracert command uses UDP to encapsulate probe packets.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 114
The broadcast address of the subnet 192.168.1.0/25 is 192.168.1.128.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 115
A network administrator wishes to assign an IP address to a router interface G0/0/0. Which of the following IP addresses can be assigned?
A. 192.168.10.112/30
B. 237.6.1.2/24
C. 145.4.2.55/26
D. 127.3.1.4/28
Correct Answer: C
Section: (none)
Explanation
QUESTION 116
In the VRP system, what are the functions of Ctrl+Z?
A. Return from the system view to the user view

B. Exit from the current view
C. Exit from the interface view
D. Exit from the console interface view
885CB989129A5F974833949052CFB2F2
E. Return to the user view
Correct Answer: A
Section: (none)
Explanation
QUESTION 117
Assuming all STP enabled switches have the same bridge priority. The MAC address of switch A is 00-e0-fc-00-00-40, the MAC address of switch B is 00-e0-fc-00-
00-10, the MAC address of switch C is 00-e0-fc-00-00-20, and the MAC address of switch D is 00-e0-fc-00-00-80.
Which switch will be elected as the root switch?
A. Switch A
B. Switch B
C. Switch C
D. Switch D
Correct Answer: B
Section: (none)
Explanation
QUESTION 118
As specified by the RSTP protocol, when a root port fails, which type of port will function as a new root port and enters the forwarding state without any delay?
A. Forwarding Port
B. Alternate Port
C. Backup Port
D. Edge Port
Correct Answer: B
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 119
Refer to the graphic. RTA and RTB are running RIPv1. RTA has advertised 10.0.0.0 and 192.168.1.0 to the RIP network. Which routes will exist in the IP routing
table of RTB? (Choose all that apply)
A. 10.0.0.0/8
B. 192.168.1.1/32
C. 10.1.12.1/32
D. 192.168.1.0/24
Correct Answer: AD
Section: (none)
Explanation
QUESTION 120
Refer to the graphic. An administrator has configured RIPv2 in the two routers. What will happen after configuring the following commands: (Choose all that apply)
885CB989129A5F974833949052CFB2F2
A. RTA will have the route learned from the RTB
B. RTB will have the route learned from the RTA
C. RTA will have no neighbor relationship with RTB
D. RTB will have no neighbor relationship with RTA
Correct Answer: AD
Section: (none)
Explanation
QUESTION 121
Refer to the graphic. OSPF is used on four routers that are in the same area and on the same network segment. In this scenario, OSPF selects one DR and
multiple BDRs to ensure backup.
A. True
B. False
Correct Answer: B
Section: (none)
885CB989129A5F974833949052CFB2F2
Explanation
QUESTION 122
Which of the following configurations regarding default route configuration is correct?
A. [Quidway] ip route-static 0.0.0.0 0.0.0.0 172.16.2.1

B. [Quidway] ip route-static 0.0.0.0 255.255.255.255 172.16.2.1
C. [Quidway-GigabitEthernet0/0/1] ip route-static 0.0.0.0 0.0.0.0 172.16.2.1
D. [Quidway] ip route static 0.0.0.0 0.0.0.0 172.16.2.1
Correct Answer: A
Section: (none)
Explanation
QUESTION 123
Refer to the graphic. GE0/0/1 and GE0/0/2 on the switch are configured as hybrid interfaces. Which of the following statements are true? (Choose all that apply)
885CB989129A5F974833949052CFB2F2
A. The administrative department and the finance department cannot communicate with each other because the VLANs of the two departments are different.
B. The data frames sent by the administrative department carry tagged VLAN 20 on the switch.
C. On the switch, the data frames sent by the finance department carry tagged VLAN 20.
D. The switch can be a Layer 2 or Layer 3 switch because communications do not need to be transmitted through a Layer 3 gateway.
E. If GE0/0/1 and GE0/0/2 on the switch are changed to trunk ports, the administrative department and finance department can communicate with each other.
Correct Answer: BC
Section: (none)
Explanation
QUESTION 124
An ACL does not filter traffic generated by the Huawei device towards other devices, but only filters forwarded traffic, including traffic generated by other devices to
access the Huawei device.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 125
Which of the following statements are true about ACL deployment on Huawei devices? (Choose all that apply)
885CB989129A5F974833949052CFB2F2
A. ACL can only be used in the outbound direction of an interface
B. The same ACL can be used on multiple interfaces
C. The ACL rules can only be configured in the following sequence: 10, 20, 30…
D. ACLs cannot be used to filter OSPF traffic because OSPF does not use UDP to encapsulate packets
E. ACLs can be used to match with the TCP/UDP port IDs of packets and to designate the port ID range
Correct Answer: BE
Section: (none)
Explanation
QUESTION 126
VLSM can expand any IP network segment, including Class D addresses.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
QUESTION 127
Which of the following statements are true about ICMP messages? (Multiple Choice)
A. ICMP messages can record time, including the original time, packet receiving time, and packet sending time.
B. ICMP messages are encapsulated in IP packets but not at the transport layer.
C. ICMP messages include error messages, control messages, request/response messages, and update messages.
D. ICMP does not support redirection.
E. ICMP messages cannot be used to detect a path’s MTU.
Correct Answer: BC
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 128
If a network’s broadcast address is 172.16.1.255, which of the following addresses can be the network address?
A. 172.16.2.0
B. 172.16.1.253
C. 172.16.1.128
D. 172.16.1.1
Correct Answer: C
Section: (none)
Explanation
QUESTION 129
On the command line interface of Huawei AR routers, the role of the Save command is to Save the current system time.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
QUESTION 130
Which of the following technologies is used to bind MAC addresses to interfaces on a switch?
A. SEP.
B. Port security.
C. ACL.
D. NAT.
885CB989129A5F974833949052CFB2F2
Correct Answer: B
Section: (none)
Explanation
QUESTION 131
During STP calculation, the port cost is associated with port bandwidth. Which of the following statements about the relation between port cost and port bandwidth is
true?
A. Port cost decreases when port bandwidth increases.

B. Port cost increases when port bandwidth increases.
C. Port cost is consistent with port bandwidth.
D. Port cost varies randomly according to port bandwidth.
Correct Answer: A
Section: (none)
Explanation
QUESTION 132
Which of the following statements about static route preference on Huawei devices is false?
A. Static route preference ranges from 0 to 255.

B. Default static route preference is 60.
C. Static route preference is either internal or external. Administrators can modify external preferences.
D. If static route preference is 255, the route cannot be used.
Correct Answer: A
Section: (none)
Explanation
QUESTION 133
In an RIP process on a Huawei device, which of the following configurations are correct for advertising network 10.1.1.1/30? (Multiple Choice)
885CB989129A5F974833949052CFB2F2
A. network 10.1.1.0
B. undo summary
network 10.1.1.0
C. version 2
undo summary
network 10.0.0.0
D. undo summary
network 10.1.0.0
E. network 10.0.0.0
Correct Answer: B
Section: (none)
Explanation
QUESTION 134
The following configuration commands implement route backup on RTA for a route to the same destination 10.1.1.0.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
QUESTION 135
Which of the following network types does OSPF support? (Multiple Choice)
A. Point-to-Point.
B. Broadcast.
885CB989129A5F974833949052CFB2F2
C. Non-Broadcast Multi-Access.
D. Point-to-Multipoint.
Correct Answer: ABCD

Section: (none)
Explanation
QUESTION 136
A DHCP Offer packet can carry only one DNS server address.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
QUESTION 137
Refer to the graphic. Host A and Host B use VLAN routing to facilitate communication. What must be configured on interface G0/0/1.1 of RTA to achieve this?
885CB989129A5F974833949052CFB2F2
A. dot1q termination vid 1.
B. dot1q termination vid 10.
C. dot1q termination vid 20.
D. dot1q termination vid 30.
Correct Answer: B
Section: (none)
Explanation
QUESTION 138
Refer to the configuration output. Which following statements are correct? (Multiple choice)
885CB989129A5F974833949052CFB2F2
A. VLAN 1 cannot pass over interface Gigabit Ethernet 0/0/1.
B. VLAN 1 can pass over interface Gigabit Ethernet 0/0/1.
C. Prior to changing the link-type to access, the command “undo port trunk allow-pass vlan all” must be used to renew the default configurations.
D. Prior to changing the link-type to access, the command “undo port trunk allow-pass vlan 2 to 4096” must be used to renew the default configurations.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 139
Link aggregation is a common technique in enterprise network. Which of the following description is the advantages of link aggregation? (Multiple Choice)
A. Improves link bandwidth.

B. Implements load sharing.
C. Improves network reliability.
D. Facilitates data copy for analysis.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 140
On Huawei switches, VLAN 4095 cannot be created and VLAN 1 cannot be deleted.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
885CB989129A5F974833949052CFB2F2
Explanation
QUESTION 141
Refer to the graphic, after the ping 10.1.1.2 command is executed on R1, LSW1 receives a tagged data frame from VLAN 10 on LSW2.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 142
Refer to the graphic, which of the following statements are true about VLAN configuration on Huawei switches? (Multiple Choice)
A. Client1 belongs to VLAN 10 and the VLAN assignment command on LSW1 is correct.
B. Client2 belongs to VLAN 20, and the MAC address-based VLAN assignment command on LSW1 is correct.
C. Client3 is in VLAN 30, and the VLAN assignment command on LSW1 is correct.
D. Client4 belongs to VLAN 40, and the VLAN assignment command on LSW1 is correct.
E. Client4 does not belong to VLAN 40, and the VLAN assignment command on LSW1 is incorrect.
Correct Answer: ABE

Section: (none)
Explanation
QUESTION 143
According to the following topology and configuration, R1 and R2 are connected through low-speed serial cables and PPP is used to encapsulate data link layer
packets. When the Holdtime values of R1 and R2 are different, PPP negotiation and communication fail.
885CB989129A5F974833949052CFB2F2
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
QUESTION 144
Which SNMP version focuses on two main aspects, namely security and administration. The security aspect is addressed by offering both strong authentication and
data encryption for privacy. The administration aspect is focused on two parts, namely notification originators and proxy forwarders.
A. SNMPv1
B. SNMPv2
C. SNMPv2c
D. SNMPv3
Correct Answer: D
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 145
According to the configuration of single-armed routing in the following figure, the administrative department and finance department can communicate with each
other even the proxy ARP is disabled on the subinterface on R1.
A. True
B. False
Correct Answer: B
885CB989129A5F974833949052CFB2F2
Section: (none)
Explanation
QUESTION 146
In the private network, RTA dynamically assigns a public address from the address pool to hosts
without port translation. Host C wishes to access the public network while addresses are assigned to Host A and Host B. What will occur as a result?
A. The first public address will be allocated to Host C, and Host A will be forced offline.
B. The last public address will be allocated to Host C, and Host B will be forced offline.
C. Host C will be unable to forward traffic over the public network.
D. All hosts will have access to the public network through pool address swapping.
Correct Answer: C
Section: (none)
Explanation
QUESTION 147
After the keepalive function is enabled for a GRE tunnel, the local end of the GRE tunnel sends a keepalive packet to the remote end every 10s.
885CB989129A5F974833949052CFB2F2
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 148
In RSTP mode, both alternate and backup ports cannot forward user traffic but can receive, process, and send BPDU.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 149
The switch is operating using STP. All default parameters have been maintained. Which port will be assigned a designated port role?
A. G0/0/1 of switch A.
B. G0/0/2 of switch A.
C. E0/0/1 of the hub.
885CB989129A5F974833949052CFB2F2
D. E0/0/2 of the hub.
Correct Answer: A
Section: (none)
Explanation
QUESTION 150
How can the default route be generated? (Choose all that apply.)
A. Manually configured.
B. Automatically generated by the router.
C. Generated by dynamic routing protocols.
D. Generated by link layer protocols.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 151
885CB989129A5F974833949052CFB2F2
The routing table includes direct routes and static routes and the preference of the direct routes cannot be changed.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 152
885CB989129A5F974833949052CFB2F2
Host A and Host B use VLAN routing to facilitate communication. When interface G0/0/1.2 of RTA receives a frame from Host B, what will RTA do?
A. RTA will immediately forward the frame via interface G0/0/1.1.

B. RTA remove the VLAN tag before forwarding the frame.
C. RTA will remove the VLAN tag and add a new tag for VLAN10 before forwarding the frame.
D. RTA will discard the frame.
Correct Answer: B
Section: (none)
Explanation
QUESTION 153
Refer to the configuration output.
Which of the following statements regarding the configuration output are correct? (Choose all that apply.)
A. The PVID on interface GigabitEthernet0/0/1 is 10.

B. The PVID on interface GigabitEthernet0/0/1 is 1.
C. The PVID on interface GigabitEthernet0/0/2 is 10.
D. The PVID on interface GigabitEthernet0/0/2 is 1.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 154
885CB989129A5F974833949052CFB2F2
A web server in a private network is required to provide HTTP services to public users. The network administrator is required to configure NAT on RTA. Which
configuration should be used?
A. [RTA-Serial1/0/1]nat server protocol tcp global 202.10.10.1 www.inside 192.168.1.1 8080

B. [RTA-Serial0/0/1]nat server protocol tcp global 192.168.1.1 www.inside 202.10.10.1 8080
C. [RTA-Gigabitethernet0/0/1]nat server protocol tcp global 202.10.10.1 www.inside 192.168.1.1 8080
D. [RTA-Gigabitethernet0/0/1]nat server protocol tcp global 192.168.1.1 www.inside 202.10.10.1 8080
Correct Answer: A
Section: (none)
Explanation
QUESTION 155
On an FR network, when the fr inarp command is executed, the interface where static address mapping entries have been configured sends an Inverse ARP
Request packet to the remote device to replace the static address mapping entries.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 156
Which of the following fields are contained in an ARP packet?
885CB989129A5F974833949052CFB2F2
A. Source Hardware Address
B. Hardware Type
C. Source Protocol Address
D. Operation Code
Correct Answer: B
Section: (none)
Explanation
QUESTION 157
When a network engineer enters a command, the following information is displayed:
Error: Unrecognized command found at '^' position. Which of the following statements is true about such information?
A. The parameter type is incorrect.

B. The entered command is incomplete.
C. The entered parameter is not specified.
D. No keyword is found.
Correct Answer: D
Section: (none)
Explanation
QUESTION 158
In RSTP mode, interfaces in the Discarding state discard received data frames but maintain the MAC address table based on received data frames.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 159
Which of the following statements is true about the MAC address table of a switch?
A. The MAC address 5489-9811-0b49 is manually configured by the administrator.

B. The MAC address 5489-989d-1d30 is manually configured by the administrator.
C. The MAC address 5489-9885-18a8 is manually configured by the administrator.
D. After the switch restarts, all the MAC addresses need to be learned again.
Correct Answer: A
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 160
The MAC address table of a switch is as follows. If the switch receives a data frame whose destination MAC address is 5489-9885-18a8 from Eth0/0/2, which of the
following statements is true?
A. The data frame is forwarded through Eth0/0/2.

B. The data frame is flooded.
C. The data frame is forwarded through Eth0/0/1.
D. The data frame is discarded.
Correct Answer: D
Section: (none)
Explanation
QUESTION 161
Which of the following descriptions about STP designated ports is correct?
A. Designated ports forward frames destined for the root switch.

B. Designated ports represent the path leading to the root switch.
C. Each bridge can have only one designated port.
D. Designated ports are responsible for sending BPDU to connected network segments.
Correct Answer: D
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 162
What is the total length of the port ID in STP?
A. 4 bits
B. 8 bits
C. 2 bits
D. 16 bits
Correct Answer: D
Section: (none)
Explanation
QUESTION 163
ICMP packets do not contain port numbers. Therefore, NAPT cannot be used.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 164
Which of the following protocols can be used on a Layer 2 network with redundant links to prevent loops?
A. UDP
B. VRRP
C. STP
D. ARP
Correct Answer: C
885CB989129A5F974833949052CFB2F2
Section: (none)
Explanation
QUESTION 165
You can configure a static route on a broadcast interface by specifying the next-hop IP address or outbound interface.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 166
Which of the following statements are true about the default route?
A. In a routing table, the route to 0.0.0.0 (with the mask being 0.0.0.0) is the default route.
B. If the destination address of a packet does not match any entry in the routing table, the packet is forwarded through the default route.
C. The default route can only be manually configured by the administrator.
D. The routing table of any router must contain the default route.
Correct Answer: AB
Section: (none)
Explanation
QUESTION 167
Which of the following OSPF packets can ensure LSA update reliability?
A. DD
B. LSR
C. LSU
885CB989129A5F974833949052CFB2F2
D. LSACK
Correct Answer: C
Section: (none)
Explanation
QUESTION 168
On the network shown in the figure, if all routers run OSPF, which router is elected as the BDR?
885CB989129A5F974833949052CFB2F2
A. Router B
B. Router A
C. Router D
D. Router C
Correct Answer: B
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 169
On the network shown in the figure, if all links are Ethernet links and all routers run OSPF, how many DRs will be elected on the entire network?
A. 2
B. 4
C. 3
D. 1
Correct Answer: B
Section: (none)
Explanation
QUESTION 170
885CB989129A5F974833949052CFB2F2
As shown in the preceding VTY configuration, the user privilege level is set to 3.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 171
As shown in the following figure, switch A and router A are connected through two links. The two links are aggregated in manual load balancing mode. The
aggregation port number is 1. The aggregated link needs to carry VLAN tag 100. Switch A uses the trunk link.
Which of the following configurations need to be performed on switch A?
885CB989129A5F974833949052CFB2F2
A.
B.
C.
D.
Correct Answer: B
Section: (none)
Explanation
QUESTION 172
According to the following topology and configuration, R1 and R2 are connected through low-speed serial cables and PPP is used to encapsulate data link layer
885CB989129A5F974833949052CFB2F2
packets. When the Holdtime values of R1 and R2 are different, PPP negotiation and communication fail.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 173
Which of the following is not included in AAA?
A. Audit
B. Authentication
C. Authorization
D. Accounting
Correct Answer: A
Section: (none)
885CB989129A5F974833949052CFB2F2
Explanation
QUESTION 174
Which of the following encapsulation modes are supported by IPsec VPN? (Choose two.)
A. Routing mode
B. Tunnel mode
C. Transport mode
D. Switching mode
Correct Answer: BC
Section: (none)
Explanation
QUESTION 175
The IKE protocol is used to set up an SA for IPsec automatic negotiation. Identity authentication can be performed when the IP address of the initiator changes
dynamically.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 176
Which of the following SNMP packets is sent by the agent on the managed device to the NMS?
A. Get-Request
B. Response
C. Get-Next-Request
885CB989129A5F974833949052CFB2F2
D. Set-Request
Correct Answer: B
Section: (none)
Explanation
QUESTION 177
Which of the following statements are true according to the following command output?
A. The OSPFv3 area ID is 0.

B. The OSPFv3 process ID is 1.
C. The DR priority of the local router is 1.
D. The router ID of the neighbor is 10.0.1.1.
Correct Answer: ABC

Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 178
Which of the following address types are of IPv6 addresses?
A. Unicast address
B. Anycast address
C. Multicast address
D. Broadcast address
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 179
In the MPLS domain, the full name of LER is label egress router.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 180
Which area ID is used by OSPFv3 to identify the backbone area?
A. 0
B. 3
C. 2
D. 1
Correct Answer: A
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 181
Which of the following statements is true about the Forward Delay timer of STP?
A. Reduce the interval for sending BPDUs.

B. Improve the configuration BPDU lifetime, ensuring that the configuration BPDUs can be forwarded to more switches.
C. Improve the STP convergence speed.
D. Prevent temporary loops.
E. Delay is required when a port transitions between Blocking and Disabled.
Correct Answer: D
Section: (none)
Explanation
QUESTION 182
Which of the following statements is true about the MAC address table of a switch?
885CB989129A5F974833949052CFB2F2
A. The switch discards the data frame whose source MAC address is 5489-9811-0b49.
B. The switch discards the data frame whose destination MAC address is 5489-9885-18a8.
C. The switch discards the data frame whose destination MAC address is 5489-9811-0b49.
D. The switch discards the data frame whose destination MAC address is 5489-989d-1d30.
Correct Answer: B
Section: (none)
Explanation
QUESTION 183
Which of the following parameters is not contained in STP configuration BPDUs?
885CB989129A5F974833949052CFB2F2
A. Root ID
B. VLAN ID
C. Bridge ID
D. Port ID
Correct Answer: B
Section: (none)
Explanation
QUESTION 184
Which layer of the OSI reference model does a router work at?
A. Physical layer
B. Data link layer
C. Network layer
D. Transport layer
Correct Answer: C
Section: (none)
Explanation
QUESTION 185
Which of the following entries is not included in the routing table?
A. MAC
B. Next-hop address
C. Destination/Mask
D. Cost
Correct Answer: A
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 186
Which of the following packets is used by OSPF to discover and maintain neighbor relationships?
A. HELLO
B. LSU
C. LSR
D. DD
Correct Answer: A
Section: (none)
Explanation
QUESTION 187
On the network shown in the figure, all routers run OSPF and the cost value is above the link. Which of the following is the path for Router A to send packets to
10.0.0.0/8?
885CB989129A5F974833949052CFB2F2
A. A-B-D
B. A-C-D
C. RA fails to reach 10.0.0.0/8.
D. A-D
Correct Answer: B
Section: (none)
Explanation
QUESTION 188
An administrator wishes to configure a floating static route. In order to successfully achieve this, which operation should be performed?
A. The administrator is required to configure a different preference values for the primary static route and floating static route.
B. The administrator is required to configure a different costs metric for the primary static route and floating static route.
C. The administrator is required to configure different route tags for the primary static route and floating static route.
D. The administrator is only required to configure two static routes.
Correct Answer: A
Section: (none)
Explanation
QUESTION 189
If a route destined for the same network has multiple next hops, what is the route?
A. Sub-optimal route
B. Multi-path route
C. Default route
D. Equal-cost route
Correct Answer: D
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 190
When searching the routing table, a router follows the longest matching rule.
Which of the following parameters does the length is the longest matching rule indicate?
A. Next-hop IP address length

B. Cost
C. Mask length
D. Preference value of the routing protocol
Correct Answer: C
Section: (none)
Explanation
QUESTION 191
Segment routing (SR) defines destination address prefixes/nodes and adjacencies on the network as segments and allocates segment IDs (SIDs) to these
segments. Adjacency and prefix/node SIDs are non-sequentially arranged in a segment list to form a forwarding path.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 192
Which of the following OSPF packets can be used to confirm the received Link State Update (LSU) packets?
A. LSR
B. LSA
C. LSU
885CB989129A5F974833949052CFB2F2
D. LSACK
Correct Answer: D
Section: (none)
Explanation
QUESTION 193
On the network shown in the figure, after the OSPF protocol state is stable, what is the neighbor status between Router A and Router B?
885CB989129A5F974833949052CFB2F2
A. Attempt
B. Full
C. 2-way
D. Down
Correct Answer: C
Section: (none)
Explanation
QUESTION 194
Which of the following statements is true?
A. Switches work at the physical layer.

B. Switches work at the network layer.
C. Routers work at the network layer.
D. Routers work at the physical layer.
Correct Answer: C
Section: (none)
Explanation
QUESTION 195
What is the destination IP address of DHCP Discover packets?
A. 127.0.0.1
B. 224.0.0.1
C. 224.0.0.2
D. 255.255.255.255
Correct Answer: D
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 196
The following shows the DHCP address pool configuration of a router. Which of the following statements are true? (Choose three.)
A. The lease time of the IP address is 12 hours.

B. The DHCP client may obtain the IP address 192.168.1.2.
C. The address pool has 199 available IP addresses.
D. The address pool has 55 available IP addresses.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 197
The following shows the Eth-Trunk information on a switch. Which of the following commands can be used to delete Eth-Trunk 1?
885CB989129A5F974833949052CFB2F2
A. undo interface Eth-Trunk 1
B. inte GigabitEthernet 0/0/1
undo eth-trunk
quit
inte GigabitEthernet 0/0/2
undo eth-trunk
quit
undo interface Eth-Trunk 1
C. inte GigabitEthernet 0/0/1
undo eth-trunk
quit
D. inte GigabitEthernet 0/0/2
undo eth-trunk
quit
Correct Answer: B
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 198
Which of the following statements about VLANIF interfaces is correct?
A. Different VLANIF interfaces can use the same IP address.

B. A VLANIF interface does not have a MAC address.
C. VLANIF interfaces do not need to learn MAC addresses.
D. A VLANIF interface is a Layer 3 interface.
Correct Answer: D
Section: (none)
Explanation
QUESTION 199
What is the value of the Flag field in the PPP frame format?
A. 0x7E
B. 0xFF
C. 0x8E
D. 0xEF
Correct Answer: A
Section: (none)
Explanation
QUESTION 200
Two routers are connected through serial interfaces and support PPP encapsulation.
Which parameters must be negotiated to establish the PPP connection? (Choose three.)
A. MRU
B. Authentication password
885CB989129A5F974833949052CFB2F2
C. Magic-Number
D. Authentication Protocol
Correct Answer: ACD

Section: (none)
Explanation
QUESTION 201
Which of the following ACLs can match the transport layer port number?
A. Basic ACL
B. Intermediate ACL
C. Layer 2 ACL
D. Advanced ACL
Correct Answer: D
Section: (none)
Explanation
QUESTION 202
On a broadcast network with four routers, all the routers run OSPFv3, and the DR priorities of all the routers are not 0. How many adjacencies are there on the
network?
A. 4
B. 6
C. 5
D. 3
Correct Answer: A
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 203
IPv6 can also be called:
A. RIPng
B. IP+
C. IPng
D. NextIP
Correct Answer: C
Section: (none)
Explanation
QUESTION 204
Refer to the graphic, the static NAT command is executed on R1. When a PC connected to R1 accesses the Internet, the destination address in the packets does
not change.
[R1]interface GigabitEthernet1/0/0
[R1-GigabitEthernet1/0/0]ip address 192.168.0.1 255.255.255.0
#
[R1]interface GigabitEthernet2/0/0
[R1-GigabitEthernet2/0/0]ip address 202.10.1.2 255.255.255.0
[R1]nat static global 202.10.1.3 inside 192.168.0.2 netmask 255.255.255.255
[R1]ip route-static 0.0.0.0 0.0.0.0 202.10.1.1
A. True
B. False
885CB989129A5F974833949052CFB2F2
Correct Answer: A
Section: (none)
Explanation
QUESTION 205
For DHCP, the priority of an interface address pool is higher than that of a global address pool.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 206
Before forwarding IPv6 packets, routers do not need to re-encapsulate the data link layer.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 207
In the VRP system, you cannot delete files by running the delete or unreserved vrpcfg.zip command. You must clear files in the recycle bin.
A. True
B. False
885CB989129A5F974833949052CFB2F2
Correct Answer: B
Section: (none)
Explanation
QUESTION 208
What is the neighbor state when an OSPFv3 adjacency is established?
A. Down
B. 2-way
C. Full
D. Loading
Correct Answer: B
Section: (none)
Explanation
QUESTION 209
Which of the following values of the Length/Type field in an Ethernet data frame indicates the PPPoE discovery stage?
A. 0×8863
B. 0×8864
C. 0×0806
D. 0×0800
Correct Answer: A
Section: (none)
Explanation
QUESTION 210
Which of the following fields is not included in the OSPF Hello packet?
885CB989129A5F974833949052CFB2F2
A. Hello Interval
B. Neighbor
C. Network Mask
D. Sysname
Correct Answer: D
Section: (none)
Explanation
QUESTION 211
If the configuration information of a router is as follows, which user name and password are used by the peer router to perform PPP link authentication?
aaa
local-user test password cipher test
local-user test service-type ppp
local-user test1 password cipher test1
local-user test1 service-type telnet
local-user test2 password cipher test2
#
interface Serial1/0/0
link-protocol ppp
ppp authentication-mode pap
ip address 10.0.12.1 255.255.255.0
#
A. User name: test

Password: test
B. User name: test1
Password: test1
C. User name: test2
Password: test2
D. User name: test2
Password: test
Correct Answer: A
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 212
As shown in the figure, which of the following ports will become the designated port?
A. G0/0/3 of SWB
B. G0/0/1 of SWC
C. G0/0/2 of SWC
D. G0/0/1 of SWB
Correct Answer: D
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 213
Which of the following commands can be used to change the device name to huawei?
A. sysname huawei
B. hostname huawei
C. rename huawei
D. do name huawei
Correct Answer: A
Section: (none)
Explanation
QUESTION 214
Which layer of the OSI reference model does the PPP protocol define?
A. Presentation layer
B. Data link layer
C. Network layer
D. Application layer
Correct Answer: B
Section: (none)
Explanation
QUESTION 215
What is the UDP port number used by the DHCPv6 server?
A. 546
B. 547
C. 548
D. 549
Correct Answer: B
885CB989129A5F974833949052CFB2F2
Section: (none)
Explanation
QUESTION 216
Which of the following statements is false about OSPF area partition?
A. The link state databases (LSDBs) of routers are the same in the same OSPF area.
B. OSPF area partition can reduce the LSDB size of the router.
C. Area 0 is the backbone area, and other areas must be connected to this area.
D. Only area border routers (ABRs) can function as the autonomous system boundary routers (ASBRs).
Correct Answer: B
Section: (none)
Explanation
QUESTION 217
Which of the following OSPF packets can be sent to request the local lacking LSAs?
A. HELLO
B. LSU
C. LSR
D. LSACK
Correct Answer: C
Section: (none)
Explanation
QUESTION 218
What is the destination address of DHCPv6 request packets?
A. FF02::1:2
885CB989129A5F974833949052CFB2F2
B. FF02::1
C. FF02::2
D. FF01::1:2
Correct Answer: A
Section: (none)
Explanation
QUESTION 219
MPLS dual-label stacking packets are _____ bytes longer than original IP packets.
A. 4
B. 8
C. 16
D. 32
Correct Answer: B
Section: (none)
Explanation
QUESTION 220
If the IPv4 address of a host on a local area network (LAN) is 192.168.1.1/30, which of the following destination IPv4 addresses can be carried in data packets that
the host can decapsulate?
A. 192.168.1.1
B. 192.168.1.2
C. 192.168.1.3
D. 255.255.255.255
Correct Answer: B
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 221
Which of the following is/are the characteristic(s) of HDLC?
A. HDLC supports point-to-point links.

B. HDLC does not support IP address negotiation.
C. HDLC does not support authentication.
D. HDLC supports point-to-multipoint links.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 222
Which of the following types of routes can be used by a router to establish a routing table?
A. Direct route
B. Dynamic route
C. Static route
D. Aggregated route
Correct Answer: AC
Section: (none)
Explanation
QUESTION 223
On the network shown in the figure, which of the following commands can be used to enable host A to successfully ping host B?
885CB989129A5F974833949052CFB2F2
A. Router A : ip route-static 10.0.12.5 255.255.255.252 11.0.12.2
Router B : ip route-static 10.0.12.1 255.255.255.252 11.0.12.1
B. Router A : ip route-static 0.0.0.0 0.0.0.0 11.0.12.2
C. Router A : ip route-static 0.0.0.0 0.0.0.0 11.0.12.1
D. Router A : ip route-static 10.0.12.5 255.255.255.252 11.0.12.1
Correct Answer: AB
Section: (none)
Explanation
885CB989129A5F974833949052CFB2F2
QUESTION 224
Which of the following packets are OSPF packets?
A. HELLO
B. LSU
C. LSR
D. LSA
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 225
Which of the following port status may exist on an STP-enabled switch?
A. Forwarding
B. Listening
C. Discarding
D. Disabled
Correct Answer: AB
Section: (none)
Explanation
QUESTION 226
One of the reasons that segment routing (SR) is introduced is that traditional LDP has some restrictions.
Which of the following statements about LDP restrictions are true?
A. LDP does not support automatic label allocation.

B. LDP supports path computation only based on IGP SPF (minimum cost), not based on traffic engineering.
C. LDP path computation depends on an IGP. If the IGP and LDP are not synchronized, black holes are generated, affecting services.
885CB989129A5F974833949052CFB2F2
D. LDP has 11 types of protocol packets, which greatly increases link bandwidth consumption and device CPU usage.
Correct Answer: CD
Section: (none)
Explanation
QUESTION 227
Which of the following statements about Ethernet sub-interfaces is/are true?
A. The sub-interface ID must be the same as the VLAN ID.

B. A sub-interface can be bound to multiple VLANs.
C. The sub-interface cannot be configured with an IP address.
D. The IP addresses for sub-interfaces must not be on the same network segment.
Correct Answer: C
Section: (none)
Explanation
https://www.gratisexam.com/.
885CB989129A5F974833949052CFB2F2

Huawei Prep4sure H12-211 v2021-04-28 by Jude 227q

Uploaded by

Copyright:

Available Formats

Huawei Prep4sure H12-211 v2021-04-28 by Jude 227q

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Huawei Prep4sure H12-211 v2021-04-28 by Jude 227q

Uploaded by

Copyright:

Available Formats

H12-211

B. AAA local authentication

Correct Answer: ABD

Correct Answer: ABD

A. eSight is used to monitor and manage enterprise networks.

A. Packets from network 10.0.1.0/24 network will be denied.

A. Packets from network 172.16.1.1/32 will be denied.

What will occur as a result?

A. The end stations cannot communicate.

What can the administrator determine from this?

A. The MAC address is a unicast address.

Correct Answer: BCD

A. The frame format is Ethernet_II

A. The maximum value of TTL is 65535.

A. The source router had shutdown the ICMP function.

Which statement regarding the output is correct?

A. The network administrator used the command ping -c 2 -s 800 10.0.0.2

Which statement is true about regarding the ARP reply?

A. Discard the packet.

A. The MAC address of the switch.

What effect will this have on the hosts?

A. The source MAC address

What is the possible reason for this?

A. The ports have disabled auto-negotiation.

A. Source MAC address

A. The switch learns MAC addresses automatically.

A. The user’s status has been blocked

What is the possible reason?

A. Communication failures occur between the user and the router.

Which following statements are correct? (Choose two).

A. The IP address of interface serial 1/0/1 is 10.1.1.1/24

A. Check whether the host has configured the gateway IP address.

A. Through the Console port

Correct Answer: ABC

How can this be achieved? (Choose all that apply.)

A. Versatile Routine Platform

A. Up cursor key < >

A. If Auto-Config is required, the administrator should select ‘y’.

What should he/she do?

Which IP address may be used by the client?

A. dhcp select relay

What are the possible reasons for this? (Choose three).

Correct Answer: ABD

A. An IP address from network 10.10.10.0/24 will be assigned.

A. DLCI is locally significant

A. remote logical channel ID

Correct Answer: BCD

Correct Answer: ABD

Which of the following options regarding file transfer is false?

A. Huawei router can be configured as FTP Client

Correct Answer: ABC

Which of the following commands should be used to enable this protocol?

Which of the following represent advantages of link aggregation? (Choose three)

Correct Answer: ABC

A. Maximum number of Up member links

A. The two switches will not be able to communicate.

Which translation method can be used to support this requirement?

Which configuration should be used?

Which command is correct?