SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM RS–225

Short in Front Passenger Side Front Preten-

DTC B1905/74
sioner Squib Circuit

Open in Front Passenger Side Front Preten-

DTC B1906/74
sioner Squib Circuit

Short to GND in Front Passenger Side Front

DTC B1907/74
Pretensioner Squib Circuit

Short to B+ in Front Passenger Side Front Pre-

DTC B1908/74
tensioner Squib Circuit
DESCRIPTION
The front passenger side front pretensioner squib circuit consists of the center airbag sensor assembly
RS
and the front seat outer belt assembly RH.
This circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side front pretensioner
squib circuit.
DTC No. DTC Detection Condition Trouble Area
• Center airbag sensor assembly detects line short
circuit signal in front passenger side front • Rear door wire No.1
pretensioner squib circuit 5 times during primary • Floor wire
B1905/74 check. • Front seat outer belt assembly RH (Front
• Front passenger side front pretensioner squib passenger side front pretensioner squib)
malfunction • Center airbag sensor assembly
• Center airbag sensor assembly malfunction
• Center airbag sensor assembly detects open circuit
• Rear door wire No.1
signal in front passenger side front pretensioner
• Floor wire
squib circuit for 2 seconds.
B1906/74 • Front seat outer belt assembly RH (Front
• Front passenger side front pretensioner squib
passenger side front pretensioner squib)
malfunction
• Center airbag sensor assembly
• Center airbag sensor assembly malfunction
• Center airbag sensor assembly detects short circuit
• Rear door wire No.1
to ground signal in front passenger side front
• Floor wire
pretensioner squib circuit for 0.5 seconds.
B1907/74 • Front seat outer belt assembly RH (Front
• Front passenger side front pretensioner squib
passenger side front pretensioner squib)
malfunction
• Center airbag sensor assembly
• Center airbag sensor assembly malfunction
• Center airbag sensor assembly detects short circuit
• Rear door wire No.1
to B+ signal in front passenger side front
• Floor wire
pretensioner squib circuit for 0.5 seconds.
B1908/74 • Front seat outer belt assembly RH (Front
• Front passenger side front pretensioner squib
passenger side front pretensioner squib)
malfunction
• Center airbag sensor assembly
• Center airbag sensor assembly malfunction
 RS–226 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM

WIRING DIAGRAM

2 4
KI1 K1 PP+
1
RS
1 5
KI1 K1 PP-
2

I4
Front Passenger Side Front Pretensioner Squib

(Front Seat Outer Belt Assembly RH)

Center Airbag Sensor Assembly

H101823E11

INSPECTION PROCEDURE
HINT:
• Perform the simulation method by selecting CHECK MODE (signal check) with the intelligent tester
(See page RS-39).
• After selecting CHECK MODE (signal check), perform the simulation method by wiggling each
connector of the airbag system or driving the vehicle on a city or rough road (See page RS-29).

1 CHECK CONNECTOR (REAR DOOR WIRE NO.1 - FRONT SEAT OUTER BELT ASSEMBLY
RH)

(a) Turn the ignition switch off.

(b) Disconnect the negative (-) terminal cable from the
battery, and wait for at least 90 seconds.
(c) Check the rear door wire No.1 connector and terminals
(on the front seat outer belt assembly RH side) and
check that the connector is properly connected to the
front seat outer belt assembly RH .
 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM RS–227

Result
Result Proceed to
No problem. A
Connector or terminals incorrect. B
Connector connected improperly. C

B REPAIR OR REPLACE REAR DOOR WIRE

NO.1

C CONNECT CONNECTOR PROPERLY

2 CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PASSENGER SIDE FRONT
PRETENSIONER SQUIB)

SST 09843-18060 RS
(a) Disconnect the connectors from the front seat outer belt
assembly RH.
F E CD (b) Connect the black wire side of SST (resistance 2.1 Ω) to
A connector E.
CAUTION:
Front Passenger Side Center Airbag
Never connect a tester to the front seat outer belt
Front Pretensioner Sensor Assembly
Squib
assembly RH (front passenger side front
pretensioner squib) for measurement, as this may
Connector E lead to a serious injury due to airbag deployment.
NOTICE:
• Do not forcibly insert the SST into the terminals of
the connector when connecting.
• Insert the SST straight into the terminals of the
connector.
SST
(c) Connect the negative (-) terminal cable to the battery,
and wait for at least 2 seconds.
(d) Turn the ignition switch on, and wait for at least 60
seconds.
(e) Clear the DTCs stored in the memory (See page RS-36).
DLC3 DTC74 (f) Turn the ignition switch off.
(g) Turn the ignition switch on, and wait for at least 60
seconds.
(h) Check the DTCs (See page RS-36).
OK:
CG TC DTC B1905/74, B1906/74, B1907/74 and B1908/74
C C135753E02
are not output.
HINT:
DTCs other than DTC B1905/74, B1906/74, B1907/74
and B1908/74 may be output at this time, but they are
not related to this check.
OK REPLACE FRONT SEAT OUTER BELT
ASSEMBLY RH

NG
 RS–228 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM

3 CHECK CONNECTOR (FLOOR WIRE - REAR DOOR WIRE NO.1)

(a) Turn the ignition switch off.

(b) Disconnect the negative (-) terminal cable from the
battery, and wait for at least 90 seconds.
(c) Disconnect the SST from connector E.
(d) Check the floor wire connector and terminals (on the rear
door wire No.1 side) and check that the connector is
properly connected to the rear door wire No.1.
Result
Result Proceed to
No problem. A
Connector or terminals incorrect. B
Connector connected improperly. C

RS B REPAIR OR REPLACE FLOOR WIRE

C CONNECT CONNECTOR PROPERLY

4 CHECK REAR DOOR WIRE NO.1

(a) Disconnect the floor wire connector from the rear door
wire No.1.
(b) Check for short to B+ in the circuit.
Rear Door (1) Connect the negative (-) terminal cable to the
Wire No.1 battery, and wait for at least 2 seconds.
(2) Turn the ignition switch on.
F E D C (3) Measure the voltage.
A Standard voltage
Tester Connection Condition Specified Condition
Front Passenger Side Center Airbag
Front Pretensioner Sensor Assembly 1 - Body ground Ignition switch on Below 1 V
Squib 2 - Body ground Ignition switch on Below 1 V

(c) Check for open in the circuit.

Connector E (1) Turn the ignition switch off.
(2) Disconnect the negative (-) terminal cable from the
battery, and wait for at least 90 seconds.
(3) Measure the resistance.
Standard resistance
Tester Connection Condition Specified Condition
1-2 Always Below 1 Ω

(d) Check for short to ground in the circuit.

C135754E01 (1) Measure the resistance.
Standard resistance
Tester Connection Condition Specified Condition
1 - Body ground Always 1 MΩ or higher
2 - Body ground Always 1 MΩ or higher
 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM RS–229

(e) Check for short in the circuit.

(1) Release the activation prevention mechanism built
into connector D (See page RS-29 ).
(2) Measure the resistance.
Standard resistance
Tester Connection Condition Specified Condition
1-2 Always 1 MΩ or higher

(3) Restore the released activation prevention

mechanism of connector D to the original condition.
NG REPAIR OR REPLACE REAR DOOR WIRE
NO.1

OK

5 CHECK CONNECTOR (FLOOR WIRE - CENTER AIRBAG SENSOR ASSEMBLY) RS

(a) Check the floor wire connector and terminals (on the
center airbag sensor assembly side) and check that the
connector is properly connected to the center airbag
sensor assembly.
Result
Result Proceed to
No problem. A
Connector or terminals incorrect. B
Connector connected improperly. C

B REPAIR OR REPLACE FLOOR WIRE

C CONNECT CONNECTOR PROPERLY

A
 RS–230 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM

6 CHECK FLOOR WIRE

(a) Disconnect the connectors from the center airbag sensor

Center Airbag Sensor Assembly
Rear Door assembly.
Wire No. 1 (b) Check for short to B+ in the circuit.
(1) Connect the negative (-) terminal cable to the
F E D C B battery, and wait for at least 2 seconds.
A (2) Turn the ignition switch on.
(3) Measure the voltage.
Front Passenger Side Standard voltage
Front Pretensioner Floor Wire
Tester Connection Condition Specified Condition
Squib
1 - Body ground Ignition switch on Below 1 V
2 - Body ground Ignition switch on Below 1 V

Connector C (c) Check for open in the circuit.

RS (1) Turn the ignition switch off.
(2) Disconnect the negative (-) terminal cable from the
IK2
battery, and wait for at least 90 seconds.
(3) Measure the resistance.
Standard resistance
Tester Connection Condition Specified Condition
1-2 Always Below 1 Ω
C135755E01

(d) Check for short to ground in the circuit.

(1) Measure the resistance.
Standard resistance
Tester Connection Condition Specified Condition
1 - Body ground Always 1 MΩ or higher
2 - Body ground Always 1 MΩ or higher

(e) Check for short in the circuit.

(1) Release the activation prevention mechanism built
into connector B (See page RS-29).
(2) Measure the resistance.
Standard resistance
Tester Connection Condition Specified Condition
1-2 Always 1 MΩ or higher

(3) Restore the released activation prevention

mechanism of connector B to the original condition.
NG REPAIR OR REPLACE FLOOR WIRE

OK
 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM RS–231

7 CHECK CENTER AIRBAG SENSOR ASSEMBLY

(a) Connect the floor wire connector to the rear door wire
Center Airbag Sensor Assembly
No.1.
Rear Door (b) Connect the connectors to the front seat outer belt
Wire No.1 assembly RH and the center airbag sensor assembly.
(c) Connect the negative (-) terminal cable to the battery,
and wait for at least 2 seconds.
FE DC (d) Turn the ignition switch on, and wait for at least 60
seconds.
Front Passenger Side Floor Wire (e) Clear the DTCs stored in the memory (See page RS-36).
Front Pretensioner Squib (f) Turn the ignition switch off.
DLC3 DTC74 (g) Turn the ignition switch on, and wait for at least 60
seconds.
(h) Check the DTCs (See page RS-36).
OK: RS
CG TC DTC B1905/74, B1906/74, B1907/74 and B1908/74
C127741E01
are not output.
HINT:
DTCs other than DTC B1905/74, B1906/74, B1907/74
and B1908/74 may be output at this time, but they are
not related to this check.
NG REPLACE CENTER AIRBAG SENSOR
ASSEMBLY

OK

USE SIMULATION METHOD TO CHECK