C-TRAN COMBINED 3 PHASE CT

& MULTIFUNCTION TRANSDUCER

WITH RS485 OUTPUT
DESCRIPTION
The C-Tran is combined 3 phase multifunction AC
Power transducer and 3 phase current transformer.
The C-Tran is fully programmable through either of
the two communication ports

APPLICATION
The C-Tran can replace traditional multifunction
meters and 3 separate current transformers with an
all in one combined product with RS485 output

PARAMETERS MEASURED MEMORY

• Phase Voltage (V) All data including energy registers, current and voltage
• Line Voltage (V) ratios and calibrated data is stored in a non volatile
• Phase Current (I) eeprom.
• Frequency (Hz)
• Active Power Per Phase (W) CUMMUNICATION
• System Active Power (W)
• Reactive Power Per Phase (VAr) Port 2:
• System Reactive Power (VAr) The main communication port.
• Apparent Power Per Phase (VA)
• System Apparent Power (VA) It uses the popular Modbus protocol to retrieve
• Import Active Power (W.h) measurements and to change the transducers operating
• Import Reactive Power (VAr.h) parameters. It enables the connection of a host
• Apparent Energy (VA.h) computer, PLC, RTU, Data Logger etc.
• System Power Factor (P.F.)
• Amp Demand (Ad) Port 1:
• Maximum Amp Demand (Max.Ad) This port has a fixed data format, It can also retrieve
• Import Watt Demand (Wd) measurements and set the transducer operating
• Maximum Watt Demand Import (Max.Wd) parameters. Only the baud rate and endian format can
• VA Demand (VAd) be changed on this port.
• Maximum VA Demand (Max. VAd)
• Neutral Current Can connect with M850-LCM display with this port
• Hours Run—Voltage based
PROGRAMMING
ACCURACY Setup and monitoring software is available from
The accuracy of the C-Tran is Class 0.2 to IEC688 over Our website www.hobut.co.uk
the range 10% to 120% In, and for voltages from
100V to 120% of nominal input.
For Active and Reactive energy the accuracy is 1% of
the reading to IEC 1036.
The accuracy of the current transformer is Class 1 for
the range 10% to 120% of nominal input.

Our policy is one of continuous development and therefore specifications may change without notice.

Howard Butler Ltd. www.hobut.co.uk

Page 1 of 3
C-TRAN COMBINED 3 PHASE CT
& MULTIFUNCTION TRANSDUCER
WITH RS485 OUTPUT
INSTALLATION OPTIONS
OPTION 1
2)
5(
RS 4
8 Multiple C-Trans can be connected to PC, PLC, RTU,
Data Loggers and Scada System with RS485 (Modbus)
without the need odf a display

ve
ste
r Sla
Ma

ve
Sla
OPTION 2
ve
Sla Multiple C-Trans with single display.

1 Up to 32 C-Trans can be linked together with one

single display (Display Part No. M850-LCM)

r
ste
85
(1)
Sla
ve Ma OPTION 3
RS4
Multiple C-Trans with single display.
ve
Sla

ve
(As Option 2) with RS485 remote communication
Sla
(Display Part No. M850-LCM)

C-TRAN RANGE
CURRENT PART NUMBER
ste
r 60A C-TRAN-60A
Ma
(1) 100A C-TRAN-100A
85
(2) RS4 lave
85 S
ste
r
RS4 125A C-TRAN-125A
Ma
ve 150A C-TRAN-150A
Sla
ve Sla
160A C-TRAN-160A
ve
ve Sla C-TRAN-200A
Sl a 200A
ve 250A C-TRAN-250A
Sla

OPTION PART NUMBER

3 Remote Dispaly M850-LCM

Our policy is one of continuous development and therefore specifications may change without notice.

Howard Butler Ltd. www.hobut.co.uk

Page 2 of 3
C-TRAN COMBINED 3 PHASE CT
& MULTIFUNCTION TRANSDUCER
WITH RS485 OUTPUT
GENERAL SPECIFICATION DIMENSIONS (mm)
INPUT 105

Rated Un Directly connected Voltages:

(3ph4W) 100V to 330V L-N Max
(3ph3W) 100V to 440V L-L Max
Rated In Depand on CT primary (see options)
Range 10 to 120% In 105 21
Overload Absolute maximum input: 4 x In
Frequency 50/60Hz Nominal range 45/65Hz 25

14
OPTIONS
35 35
3 Phase current available options:
60A, 100A, 125A, 150A, 160A, 200A & 250A

ACCURACY
Specified @ 23 °C 100V –100%Un, 10%-100% In 59
Parameters unless stated Class 0.2 to IEC688
Frequency Class 0.1Hz to IEC688 10
15
Power Factor Class 0.5 to IEC688
Active & Reactive Energy 1.0% of reading IEC1036 34
Current Transformer Class 1 to IEC 60044-1

INSULATION
Test Voltage 4kV RMS 50Hz for 1 min
Voltage inputs to case
CONNECTION DIAGRAMS
3kV RS485 to case and voltage L3
Input B (+)

PART 1
L2
(there is no isolation between A (-)
L1
Port 1 and Port 2) Screen
N
Impulse Test EMC 5kV transient complying B (+)

PART 2
C-TRAN
With IEC 801.EN 55020 HF L1
A (-)
Screen
L2
APPLIED STANDARD
L3
General IEC 688, BSEN 60688
BS 4889, IEC 359
Immunity EN 61326-2 3 Phase 3 Wire Unbalanced Load
Safety EN 61010—1
L3
B (+)
PART 1

L2
APPROVALS A (-)
UL, C-UL Pending L1 Screen
N B (+)
PART 2

C-TRAN
AUXILIARY A (-)
L1
Self powered maximum 440V Screen
Burden <10VA L2
L3
ENVIRONMENTAL N
Working Temperature 0 to +60 °C
Storage Temperature -30 to +65 °C 3 Phase 4 Wire Unbalanced Load
Temperature Coefficient 0.01% per °C

Our policy is one of continuous development and therefore specifications may change without notice.

HOWARD BUTLER LTD Page 3 of 3

CROWN WORKS, LINCOLN ROAD

WALSALL WS1 2EB ENGLAND
August 2015

Tel: 01922 640003 Fax: 01922 723626

International Tel: +44 1922 640003 E-mail: [email protected]
http://www.hobut.co.uk