G-Enex Video Service Manual Aruze 103

SERVICE MANUAL
G-ENEX Video Slot Gaming Machine

Version AU-1.03
August 10, 2007
Introduction
Introduction
This manual is intended for Operators, Owners, and Qualified Maintenance/Service

Personnel to provide the important information about the machine installation, operation,
and servicing.
It is strongly recommended to thoroughly read and understand this manual before starting
the machine. Please keep this manual at hand, so that you can quickly refer to it whenever
necessary.
Technical Support
Aruze Gaming America, Inc., Aruze Gaming Australia Pty. Ltd, and Aruze Gaming Africa
(Pty.) Ltd. (ARUZE thereinafter) are dedicated to providing high quality service and
maintenance. Please feel free to contact us any time.
i
Limited Warranty
Limited Warranty
ARUZE warrants that the products it manufactures will be free from defects in materials
and workmanship for a period of six (6) months commencing on the date the products are
shipped from Japan (except as otherwise provided in any separate sales agreement).
Within this period, ARUZE will provide replacement parts at no charge for the products
covered under this limited warranty when a part requires replacement.
This warranty does not cover any damage or failure caused by or attributable to improper
installation, improper usage, abuse, improper maintenance, excessive operating voltages, or
repairs performed or recommended by anyone other than an ARUZE technician or an
authorized distributor of ARUZE.
TO THE MAXIMUM EXTENT PERMITTED BY LAW, ARUZE SHALL NOT BE

LIABLE FOR ANY DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES RESULTING FROM ANY BREACH OR WARRANTY OR UNDER ANY
OTHER LEGAL THEORY (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS),
EVEN IF ARUZE HAS BEEN ADVISED OF THE POSSIBILITY OF THE DAMAGES.
ii
Safety Instructions
Safety Instructions
1. Definition of Safety Words
The safety words of DANGER, WARNING, and CAUTION are used in this manual to
indicate hazard levels. Please understand each meaning to handle the machine safely.
DANGER It warns of the immediate hazards which WILL

result in severe personnel injury or death.
WARNING It warns of hazards or unsafe practices which

COULD result in severe personnel injury or death.
CAUTION It warns of hazards or unsafe practices which

COULD result in minor personnel injury or
product/property damage.
2. Environmental Specifications
Refer to Chapter 8, “Machine Specifications”.
iii
Safety Instructions
3. Handling of LCD
Although the built-in LCD is protected from the danger of electric shock, handle it carefully
by referring to this manual.
If a problem happens, please contact your nearest distributor.
WARNING!
HIGH VOLTAGE!
Risk of Injury or Fire
Do not access
into the LCD’s
iv
Safety Instructions
4. Installation
WARNING!
To prevent an accident or a fire;
1. Install this machine on flat, stable, well-constructed floor.

2. Keep this machine away from the direct ray of the sun.
3. Keep this machine away from a dusty place.
4. Keep this machine away from water and other liquids.
5. Keep this machine away from disaster preventive facilities.
(ex. emergency exit, emergency stairs, fire hydrant, and
fire extinguisher)
6. Do not install this machine outdoors.
7. Keep this machine away from vibration.
8. Keep this machine away from dangerous articles.
5. Grounding
Be sure to GROUND this machine to prevent a current leak.
WARNING!
Risk of Electric Shock.

ARUZE makes no warranty as to accidents (including failures) caused by
improper grounding.
v
Safety Instructions
6. Disposal of Lithium Batteries
WARNING!
Risk of Injury of Fire

Care must be paid to dispose the lithium batteries. Improper disposal of
waste lithium batteries may result in heating or ignition of the batteries that
could cause personal injury or fire.
A lithium battery contains flammable substance (ex. lithium metal and organic solvents).
Because electricity may remain even in a used battery, wrap the + and – electrodes with
nonconductive material to prevent short-circuit causing a hazard.
Nonconductive material
Lithium battery
vi
Safety Instructions
7. Others
WARNING!
NEVER retrofit the machine. Retrofitting the machine could cause an

accident or a failure.
ARUZE makes no warranty as to accidents (including failures) caused by
retrofit.
1. Only qualified personnel should assemble, install, maintain, inspect, and troubleshoot
the machine.
2. Do not mount or sit on the machine. Or, do not put a heavy object on the machine.
A dented machine could cause trouble.
3. As soon as smoke, smell, and/or an unknown trouble is detected, turn off the POWER
switch and the power source breakers.
4. Before servicing the machine, turn off the POWER switch to prevent an electric
hazard.
5. Unless specified, NEVER use a multimeter for continuity check. Using a
multimeter may damage the electrical circuits.
6. The shield of the hopper motor may be hot. Wait until the shield cools down before
touching the hopper.
7. The coin diverter may be hot. Wait until it cools down before touching.
8. Never use chemical duster, thinner, benzine, alcohol, or synthetic detergent for
cleaning the machine. They will damage the surface of the machine.
9. Electrostatic discharge may damage the internal components. When accessing into the
cabinet, take the anti-static action (ex. touching the door) before proceeding.
10. Use this machine in commercial areas. Using it in residential areas is prohibited.
11. Actual currency and date format may differ slightly from the screen displays shown in
this manual.
vii
Table of Contents
Table of Contents
Page
Introduction....................................................................................................... i
Technical Support ............................................................................................. i
Limited Warranty ............................................................................................ ii
Safety Instructions .......................................................................................... iii

1. Definition of Safety Words............................................................................................iii
2. Environmental Specifications........................................................................................iii
3. Handling of LCD........................................................................................................... iv
4. Installation ...................................................................................................................... v
5. Grounding....................................................................................................................... v
6. Disposal of Lithium Batteries.................................................................................... vi
7. Others ....................................................................................................................... vii
Table of Contents .......................................................................................... viii
Chapter 1: Major Components............................................................... 1-1

1.1 Appearance .......................................................................................................... 1-1
1.2 Internal Structure ................................................................................................. 1-3
1.3 Closing Door ....................................................................................................... 1-7
Chapter 2: Installation............................................................................. 2-1

2.1 Unpacking and Inspection ................................................................................... 2-1
2.2 Cabinet Dimension .............................................................................................. 2-2
2.3 Installing the Machine on Your Cabinet Stand.................................................... 2-3
2.4 Installing Optional Tower Light .......................................................................... 2-4
2.5 Removing Shipping Screw from Security Cage.................................................. 2-5
2.6 When Mounting Player Tracking System ........................................................... 2-5
2.7 Key Lock Specifications ..................................................................................... 2-6
Chapter 3: Software Setting .................................................................... 3-1

3.1 Accessing Software Setting Mode ...................................................................... 3-1
3.2 MACHINE SETUP ............................................................................................. 3-3
3.2.1 CONFIGURE .................................................................................................. 3-4
3.2.2 SOUND SYSTEM .......................................................................................... 3-6
3.2.3 TOUCH SCREEN ........................................................................................... 3-8
viii
Table of Contents
3.2.4 TICKET PRINT TEST.................................................................................. 3-10
Chapter 4: Hardware Setting.................................................................. 4-1

4.1 Setting DIP Switch and Jumper Switch on Body I/O PCB ................................. 4-2
4.2 Setting DIP Switch and Jumper Switch on Door I/O PCB ................................. 4-4
4.3 Setting DIP Switch and Jumper Switch on GMEM PCB.................................... 4-7
4.4 Setting on GMEM Cassette PCB ........................................................................ 4-9
4.5 Setting DIP Switch on AMP PCB ..................................................................... 4-10
4.6 Setting DIP Switch and Jumper Switch on AUSCOM PCB ............................. 4-11
Chapter 5: Test Mode............................................................................... 5-1

5.1 Accessing Test Menu........................................................................................... 5-1
5.2 DIAGNOSTICS .................................................................................................. 5-3
5.2.1 INPUT TEST................................................................................................... 5-4
5.2.2 OUTPUT TEST............................................................................................... 5-5
5.2.3 REEL STRIP/PAY TEST................................................................................. 5-6
5.2.4 MONITOR TEST ............................................................................................ 5-7
5.2.5 DIP SWITCH TEST........................................................................................ 5-9
5.2.6 NOTE ACCEPTOR TEST ............................................................................ 5-10
5.3 OUT OF SERVICE ........................................................................................... 5-11
Chapter 6: Preventative Maintenance ................................................... 6-1

6.1 RAM Clear .......................................................................................................... 6-2
6.2 Maintenance Schedule......................................................................................... 6-7
6.2.1 Daily Servicing................................................................................................ 6-7
6.2.2 Quarterly Servicing ......................................................................................... 6-8
6.3 Collecting Notes from Note Stacker.................................................................... 6-9
6.3.1 When your note acceptor is an ARGUS note acceptor; .................................. 6-9
6.3.2 When your note acceptor is a CashCode note acceptor; ............................... 6-10
6.4 Clearing a Stacker Jam Error............................................................................. 6-11
6.4.1 When your note acceptor is an ARGUS note acceptor; ................................ 6-11
6.4.2 When your note acceptor is a CashCode note acceptor; ............................... 6-12
6.5 Disassembly....................................................................................................... 6-13
6.5.1 Top Box ......................................................................................................... 6-13
6.5.1.1 Escutcheon , Top Glass and Sub-LCD ...................................................... 6-13
6.5.1.2 Tower Light (Option) ................................................................................ 6-15
6.5.2 Main Cabinet ................................................................................................. 6-15
6.5.2.1 Security Cage ............................................................................................ 6-15
6.5.2.2 Body I/O PCB Housing............................................................................. 6-16
6.5.2.3 AUSCOM PCB Housing........................................................................... 6-16
6.5.2.4 Hopper ....................................................................................................... 6-17
6.5.2.5 Woofer and Speakers ................................................................................. 6-17
ix
Table of Contents
6.5.3 Main Door ..................................................................................................... 6-18

6.5.3.1 Door I/O PCB Housing ............................................................................. 6-18
6.5.3.2 Main LCD Unit ......................................................................................... 6-18
6.5.3.3 Note Entry Assembly................................................................................. 6-19
6.5.3.4 Game Control Panel .................................................................................. 6-19
6.5.3.5 Game Button.............................................................................................. 6-19
6.5.3.6 Common Button ........................................................................................ 6-20
6.5.4 Belly Door ..................................................................................................... 6-20
6.5.4.1 Belly Door Glass Lamp Assembly ............................................................ 6-20
6.5.4.2 Belly Door Glass ....................................................................................... 6-20
6.6 Replacement ...................................................................................................... 6-21
6.6.1 Lamps and Fluorescent Lamps...................................................................... 6-21
6.6.1.1 Lamps of Optional Tower Light (Candle) ................................................. 6-21
6.6.1.2 Fluorescent Light for Belly Glass ............................................................. 6-22
6.6.1.3 Fuse ........................................................................................................... 6-22
6.6.2 Lithium Battery ............................................................................................. 6-23
6.6.2.1 Replacing Lithium Batteries in Security Cage .......................................... 6-24
6.6.2.2 Replacing Lithium Battery on Body I/O PCB........................................... 6-25
6.6.2.3 Replacing Lithium Battery on Door I/O PCB ........................................... 6-26
6.6.2.4 Replacing Lithium Battery on AUSCOM PCB......................................... 6-27
6.7 Adjustment ........................................................................................................ 6-28
6.7.1 Sensitivity of CONDOR Coin Acceptor ....................................................... 6-28
6.7.2 Note Entry Level ........................................................................................... 6-29
6.8 Changing Game................................................................................................. 6-30
6.8.1 Changing GMEM Cassette............................................................................ 6-30
Chapter 7: Troubleshooting .................................................................... 7-1

7.1 Hopper Errors ...................................................................................................... 7-2
7.2 Coin Acceptor Errors........................................................................................... 7-6
7.3 Note Acceptor Errors......................................................................................... 7-11
7.4 Ticket Printer Errors .......................................................................................... 7-15
7.5 Mechanical Meter Errors................................................................................... 7-17
7.6 Backup Battery Errors ....................................................................................... 7-18
7.7 System Errors .................................................................................................... 7-21
Chapter 8: Machine Specifications......................................................... 8-1

8.1 Cabinet Name ...................................................................................................... 8-1
8.2 Overall Dimension Including Tower Light ......................................................... 8-1
8.3 Weight.................................................................................................................. 8-1
8.4 Electrical Specifications ...................................................................................... 8-1
8.5 Environment ........................................................................................................ 8-2
8.6 Coins/Notes Capacity .......................................................................................... 8-2
x
Table of Contents
Chapter 9: Parts Catalog......................................................................... 9-1

MAJOR COMPONENTS ............................................................................................... 9-1
No. 1 TOP BOX ASSEMBLY ...................................................................................... 9-2
No. 2 CABINET ASSEMBLY (1/2) ............................................................................. 9-4
No. 3 CABINET ASSEMBLY (2/2) ............................................................................. 9-7
No. 4 PC BOX AP-7 ..................................................................................................... 9-9
No. 5 NOTE ACCEPTOR (CASHCODE BV (600) ASSEMBLY)............................ 9-11
No. 6 NOTE ACCEPTOR (GPT) ASSEMBLY.......................................................... 9-13
No. 7 CONTROL PANEL ASSEMBLY ..................................................................... 9-15
No. 8 DOOR ASSEMBLY (1/2) ................................................................................. 9-17
No. 9 DOOR ASSEMBLY (2/2) ................................................................................. 9-19
No. 10 19INCH MAIN LCD ASSEMBLY............................................................... 9-22
No. 11 3 REEL ASSEMBLY .................................................................................... 9-24
No. 12 GM HOPPER ASSEMBLY (1/2).................................................................. 9-26
No. 13 GM HOPPER ASSEMBLY (2/2).................................................................. 9-28
Block Diagram .............................................................................................. 9-1
Wiring Diagram ............................................................................................ 9-1
xi
Chapter 1:Major Components
Chapter 1: Major Components

This chapter shows the major components of this machine.
1.1 Appearance
13
2
12
3
4
11
10
7
9
1. Tower Light (Option) 2. Sub-LCD

3. Main LCD (Touch Screen) 4. Ticket Printer
5. Game Buttons 6. Belly Door Glass 7. Coin Tray
8. Mechanical Meters 9. Note Entry 10. Speakers
11. Coin Head 12. Main Cabinet 13. Top Box
1-1
19
18
17
16
14
15
14. Belly Door Lock 15. Belly Door Latch 16. Main Door Latch
17. Main Door Lock 18. Power Save Keyswitch
19. RESET/AUDIT keyswitch
1-2
1.2 Internal Structure
14
1 13
10 12
4
9 11
5 7
6 8
1. Body I/O PCB Housing 2. Main LCD 3. Coin Acceptor
4. Coin Diverter 5. Door I/O PCB Housing 6. Inverter Fluorescent Lamp
7. Security Cage 8. Hopper 9. Note Acceptor
10. Ticket Printer (Optional) 11. Woofers 12. Power Box
13. Power Switch 14. AUSCOM PCB
1-3
Belly Door
5 1. Fluorescent Lamp Unit
1 2. Coin Duct
3. Coin Drop Sensor
4. Belly Door Switch
5. Note Stacker Lock
4
3
2
Main LCD
1. Inverter and Scaling PCB
Housing
2. Touch Panel PCB Housing
1-4
Security Cage
1. Connected to Power Box
1 10
2. Connected to Power Box
9
3 2 3. DSP controller from Body I/O
PCB
4. Connected to Door I/O PCB
5. Connected to Body I/O PCB

4
6. Connected to Head Connector
Located in Top Box
7. To Main LCD
8. To Speakers
5 9. GMEM Cassette
7
6 8
10. To Sub LCD
9
1. AMP PCB
2. GMEM PCB
3. Video PCB
1
4. Fan
2 5. Mother Board
6. Memory PCB
3
7. CPU Fan
8. Security Cage Door

4
Switch
8 9. Security Cage Lock
5 6 7
1-5
Power Box
8
2
1
3
4
1. Inlet
5 2. Outlet for Topper
3. Service Outlet
4. Power Box Fuse
6 5. Switch (not used)
6. Fuse for Service Outlet
7. Main Switch
8. Fuse for Switching
Regulator
7
1-6
1.3 Closing Door

To close the Main Door and/or Belly Door, pull and lift the stay lever.
CAUTION!
Do not open the Main door and Belly door at the same time. Otherwise it
may damage the surface of the door.
WARNING!
Do not put hands on speakers and/or edge of side door when you open the
main door. Otherwise it may jam your fingers.
Main Door
Belly Door
1-7
G-ENEX Video Slot Gaming Machine Chapter 2: Installation
Chapter 2: Installation
This chapter shows how to install this machine.
2.1 Unpacking and Inspection

WARNING!
The installation must be performed by qualified service personnel.

Before starting the installation, refer to “Safety Instruction”.
ARUZE cannot be held liable for damages or injuries caused by improper
installation.
Unpack the machine, and check for shipping damage. If any one is missing or damaged,
immediately report it to ARUZE or your nearest distributor.
1. Main body 1
2. Accessories
Key (B2155) 1
Key (B1963) 1
Key (231) 1
Operation & Service Manual 1
Parts Catalogue 1
Tower Light (Option) 1

Template (Option) 1
NOTE
The content of the accessories may vary according to your specifications.
2-1
2.2 Cabinet Dimension

The cabinet dimension is depicted below. Secure enough space so that the doors can be
easily opened for POWER-ON/OFF, maintenance, and so on.
<Outer Dimension>
155 (2 tiers tower light)

200 (3 tiers tower light)
1534 / 1579
1379
540 588
624 Unit: mm
Keep at least the following space between the machines.
Unit: mm
624 195 624
2-2
2.3 Installing the Machine on Your Cabinet Stand

Use the following procedure to install the machine on the cabinet-stand you prepared:
1. Place the template (option) on your cabinet Template

stand as depicted below. Back
2. Using a punch, mark the circles for
the AC power cable (a hole with 40mm dia.),
the coin drop chute (a hole with 40mm dia.),
and the fixing bolts (7 holes with 9mm dia). Front
Stand
3. Remove the template.
4. Drill the marks to make the holes.
5. Place the machine on the stand aligning the holes on the stand to their
counterparts on the machine.
6. Using hexagon coupling bolts (8 x 70mm) and flat washers, bolt the machine on
the stand.
7. Route the AC power cable into the stand.
8. Plug in the cable.
538 Unit: mm
235 200
φ42 HOLE 165 150 φ72 HOLE
85 30 for the AC power cable
(a)
97
171.2
210
251
(a)
396.8
420.5
6-φ9 HOLE ;(a)

48
589
for the fixing bolts

(a)
(a) (a)
50×48 HOLE
FRONT 115 50 for coin drop chute
130 130
COIN TRAY
2-3
2.4 Installing Optional Tower Light

Use the following procedure to install the tower light:
1. Unlock and unlatch the main door to open it.

2. Referring to Paragraphs 6.5.1.1, remove the escutcheon,
top glass, and the LCD.
3. Route the 4P cable of the tower light into the top box
through the top hole as depicted.
4. Screw down the tower light from the inside of the top
box.
5. Connect the 4P cable connector to the machine’s
connector.
6. Return the LCD, top glass and escutcheon in the
reverse order of the above.
7. Close the main door.
2-4
2.5 Removing Shipping Screw from Security Cage

Use the following procedure to remove the shipping screw from the security cage:
Shipping Screw
2. Locate the security cage just above the hopper.
3. Locate the shipping screw just above the security cage lock.
4. Loosen and remove the screw.
2.6 When Mounting Player Tracking System

Use the following procedure to mount a player tracking system.

2. Unscrew (6 screws) and detach the PTS base plate.
3. Set the tracking system assembly and screw down to fix.
2-5
2.7 Key Lock Specifications

The machine is shipped with generic door locks installed. To increase security, the
following door locks should be replaced:
Location Number of locks

Main door 1 pc.
Belly door 1 pc.
Security Cage door 1 pc.
Body I/O PCB door 1 pc.
Door I/O PCB door 1 pc.
AUSCOM PCB door 1 pc.
Note acceptor door 1 pc.
Note stacker door 1 pc.
< Door Lock>

9/32” -28
M7 x 0.75mm (0.28")
5.4mm (0.21")
6.3mm (0.25") (0.69")
33.6mm (1.32") 15.8mm (0.62")
< Door Lock Installing Hole>
19.3 mm (0.76")
16.2mm (0.64")
2-6
INSTALL CHECK LIST

1. Review the environment and power requirement.
Refer to “Safety Instruction”.
2. Unpack and inspect for shipping damage.
3. Install the machine on the cabinet stand.
4. Install the tower light on the machine if any.
5. Removing the shipping screw from the security cage
6. Install the player tracking system if necessary.
7. Replace the locks.
2-7
Chapter 3: Software Setting
WARNING!
Software setting must be done by authorized personnel.

Once your software setting is updated, all the soft meters have cleared to
zero. Write down the necessary soft meters before updating.
3.1 Accessing Software Setting Mode

When the game machine is on standby (that is, no game is being played, or there is no tilt
on this machine), you can access the software setting mode in the following procedure:
1. Turn ON and OFF the AUDIT keyswitch
to call the following screen.
AUDIT MODE – MAIN MENU
GMID: 0
PROGRAM #: ZANEP003
PROGRAM #: LOSEP003
FIRMWARE #: SPMRD046
FIRMWARE #: SPMDB046
PROGRAM #: SMOCX046
METER INFORMATION TICKET HISTORY
GAME RECALL HOPPER REFILL
MACHINE ERROR LOG

IDENTIFICATION
GAME STATISTICS MACHINE SETUP
EXIT
MOTHER BOARD BIOS #: AP31

BODY I/O PCB BIOS #: S1
DOOR I/O PCB BIOS #: S1
XCOM I/O PCB BIOS #: S1
KERNEL VERSION #: 2.6.12-1.1381_fc3 04
3-1
2. Choose “MACHINE SETUP” by touch the screen.

Otherwise, use the game buttons on control panel.
3. To exit to the game mode, touch “EXIT” or press a game button.
3-2
3.2 MACHINE SETUP

AUDIT MODE – MACHINE SETUP
CONFIGURE
SOUND SYSTEM
TOUCH SCREEN
TICKET PRINT TEST
EXIT
Choose your desired item by touching screen. the screen.

Otherwise, use the game buttons on control panel.
CONFIGURE System configuration options.

SOUND SYSTEM Sound system setup.
TOUCH SCREEN Touch screen calibration
TICKET PRINT TEST Testing connected ticket printer
3-3
3.2.1 CONFIGURE
AUDIT MODE - CONFIGURE
MACHINE NUMBER (GMID) 1 (READ ONLY)
COIN DENOMINATION (CENTS) 100 (READ ONLY)
BASE CREDIT VALUE (CENTS) 5 (READ ONLY)
VARIATION 0001 (READ ONLY)
BET BUTTON CONFIGURATION 1, 2, 3, 4, 5 (READ ONLY)
CCCE ENABLED (READ ONLY)
GAMBLE ENABLED (READ ONLY)
DATE (DD/MM/YYYY) 24/10/2005
TIME 21:18
COIN ACCEPTOR TYPE CONDOR PLUS CP130/133 (READ ONLY)
HOPPER TYPE GM
CANCEL CREDIT LEVEL (COINS) 400
REFILL AMOUNT (COINS)
PRINTER TYPE ITHACA 950
VENUE NAME
HOUSE NUMBER default house
NOTE ACCEPTOR ENABLED
$5 NOTES ACCEPTED NO *
DATE & TIME SYNCHRONIZATION DISABLED (HOST ID: ****)
TOPPER ILLUMINATION PATTERN GAME
LED BRIGHTNESS HIGH
RESIDUAL GAMBLE GAME ENABLED (READ ONLY)
DEMO MODE AND SOUND DEMO: ON DEMOSOUND: OFF
TO MODIFY THESE PARAMETERS THE DOOR MUST BE OPEN.

GAME VERSION IS [Z07006-XXLN-AU-002]
SYSTEM VERSION IS [ZEARU-AN1S-0121]
MEDIA VERSION IS [(512000)]
CONNECTION NOTE ACCEPTOR IS [GPT: AU28EB33]
CONNECTION TICKET PRINTER IS [S00122]
EXIT
Choose your desired item by touching screen.

Otherwise, use the game buttons on control panel..
To update the settings, use the PLAY 25 LINES button.
NOTE:
The items with the indications of “(READ ONLY)” can be set only just after RAM CLEAR.
3-4
To set the items with asterisks, open the main door.
MACHINE NUMBER (GMID) Machine serial number.

COIN DENOMINATION (CENTS) Token / Coin denomination in cents.
BASE CREDIT VALUE (CENTS) Base credit value in cents.
VARIATION Current game variation.
BET BUTTON CONFIGURATION Bet button configuration.
CCCE Electronic Fund Transfer setting
GAMBLE Gamble Enable (yes/no).
DATE (YYYY / MM / DD) Date setting.
TIME (HH : MM : SS) Time setting.
COIN ACCEPTOR TYPE Coin acceptor type.
HOPPER TYPE Hopper type.
CANCEL CREDIT LEVEL (COINS) Cancel credit trigger level in coins.
REFILL AMOUNT (COINS) Hopper refill amount in coins
PRINTER TYPE Printer type.
VENUE NAME Venue number to be printed on ticket.
HOUSE NUMBER House number to be printed on ticket.
NOTE ACCEPTOR Note acceptor type.
$5 BANKNOTES ACCEPTED $5 banknotes accepted (yes/no).
DATE & TIME SYNCHRONIZATION Date and time setting via host computer
TOPPER ILLUMINATION PATTERN Topper illumination pattern setting
LED BRIGHTNESS LED brightness setting
RESIDUAL GAMBLE GAME Type of residual credit gamble game
DEMO MODE AND SOUND Setting of demonstration mode.
3-5
3.2.2 SOUND SYSTEM
AUDIT MODE – SOUND SYSTEM
VOLUME SETTING MENU
SOUND TEST
EXIT
Sound volume level can be adjusted by “VOLUME SETTING MENU”, and all the game
sounds can be tested by “SOUND TEST.
VOLUME SETTING
AUDIT MODE –VOLUME SETTING MENU
MASTER VOLUME 1
BGM VOLUME 1
SOUND EFFECT VOLUME 1
ERROR VOLUME 20
SOUND TEST
CURSOR ENTER
UP
EXIT
CURSOR
DOWN
3-6
MASTER VOLUME
BGM VOLUME
SOUND EFFECT
VOLUME
ERROR VOLUME
SOUND TEST
SOUND TEST
AUDIT MODE – SOUND TEST
PAGE 1/4
BGM: REELSPIN
BGM: REELSPIN 1
BGM: REELSPIN 2
BGM: REELSPIN 3
BGM: REELSPIN 4
BGM: REELSPIN 5
BGM: FREEGAME
BGM: REEL UP
BGM: WINCOUNT
BGM: WINCOUNT 1
BGM: CONDOR INTRO
BGM: CONDOR SELECT
BGM: CONDOR ROPEUP
BGM: CONDOR ROPEUP 1
BGM: SNAKE BATTLE
BGM: SNAKE BATTLE LOOP STOP
BGM: CRISIS PLAY SOUND
BGM: LOOPUP SOUND
BGM: SUNBONUS
BGM: SELECT GATE PLAY PLAY PLAY
BGM: WINUP 1 SOUND SOUND SOUND EXIT
BGM: WINUP 11
BGM: WINUP 2 PLAY
BGM: WINUP 21 SOUND
BGM: WINUP LAST
3-7
3.2.3 TOUCH SCREEN

You can calibrate the touch screen on the LCD.
NOTE:
This calibration screen appears every after POWER-ON following RAM clear.
TOUCH SCREEN CALIBRATION
W: 800 H: 600
TOUCH POINT: 581/199
3-8
(1) Touch the five crosshairs (located at each corner and the center) to display the
following message.
TOUCH SCREEN CALIBRATION

W: 800 H: 600
TOUCH POINT: 581/199
Do you want to save the touch screen calibration result?

NO: CASH OUT YES: HELP
(2) Press the HELP button to enter the new setting.

To cancel it, press the CASH OUT button.
(3) After calibration, touch any point on the screen.

When your finger is exactly on the intersection of the two lines depicted above,
the touch panel has been successfully calibrated.
NOTE:
The coordinates of the touched point is displayed on the screen.
3-9
3.2.4 TICKET PRINT TEST
AUDIT MODE – TICKET PRINT TEST
TICKET PRINT TEST

EXIT : [GAMBLE OR COLLECT] TEST START : [TAKEWIN]
EXIT TEST
START
By pressing [TEST START] button, you can test the ticket printer.
3-10
Chapter 4: Hardware Setting
WARNING!
Hardware setting must be done by authorized personnel.

Once your hardware setting is updated, all the soft meters have cleared to
zero. Write down the necessary soft meters before updating.
Hardware machine options can be set by using the DIP and jumper switches on the Body
I/O, Door I/O, GMEM, and AUSCOM PCB’s.
NOTE:
The AUSCOM PCB is only installed on the machines to be shipped to the area where
X-Series protocol is used.
Refer to the following pages for the details.
4-1
4.1 Setting DIP Switch and Jumper Switch on Body I/O PCB
SW2
Bit 1 Battery ON/OFF
ON: Battery ON
OFF: Battery OFF
Bit 2 Rechargeable Battery ON/OFF
ON: Battery ON
OFF: Battery OFF
JP1: Not Used
4-2
<Jumper Switches>
SW2 (DIP Switch):
BIT 1:
ON (When installed):
The back-up battery is activated to detect a SECURITY
CAGE OPEN that occurred during the POWER OFF.
OFF (Factory Setting):
The back-up battery is not activated, and a SECURITY CAGE
OPEN that occurred during the POWER OFF cannot be
detected.
BIT 2:
ON: (When installed):
Secondary battery is activated as backup in addition to
Lithium battery.
Secondary battery is not activated as backup in addition to
Lithium battery.
JP1:
CLOSED (ON) (Factory Setting):
Not used.
<LED Indicators>
LED 1:
Green light flashing:
Indicates the BODY I/O PCB is operating normally.
Red light lighted with Green light flashing(quick):
Indicates the BODY I/O PCB is abnormal.
LED2:
Green light: Pilot lamp of +5V power
4-3
SW2-1 : Coin acceptance device setting
JP4 & 5 : NVRAM setting -2 : not used
JP1 : Battery ON/OFF
N
O
JP4 JP4
Battery ON 32KB 8KB Inhibit H
1
2
JP5 JP5
Battery OFF JP6 : Watchdog Timer ON/OFF
O
N
JP4 ON
2KB Inhibit L
1
2
JP5
OFF
JP4 SW2
SW1
JP5
JP1
AVR
JP6
ATmega
128-16AC
Microprocessor
JP2 LED indicators
JP3
4-4
JP7
INPUT/ OUTPUT
G
Gate Arrey
LZ95N12
J JP7 : COM setting
RS232C
Calent loop
JP8
4.2 Setting DIP Switch and Jumper Switch on Door I/O PCB
JP2 & 3 : ISP

JP3 JP2
JP8 : DC24V Power save ON/OFF
Serial Programming mode
DC24V Power save ON
DC24V Power save OFF JP3 JP2

RS232C mode (used tachpanel)
<Jumper Switches>
JP1:
CLOSED (ON) (Factory Setting):
The back-up battery is activated to detect a SECURITY CAGE
OPEN that occurred during the POWER OFF.
OPEN (OFF):
The back-up battery is not activated, and a SECURITY CAGE OPEN
that occurred during the POWER OFF cannot be detected
JP2&JP3:
JP2 1-2 CLOSED (ON) and JP3 1-2 CLOSED (ON):
The serial programming mode becomes effective.
Programs can be written into the IC4 (ATmega 128).
JP2 3-4 CLOSED (ON) and JP3 3-4 CLOSED (ON) (Factory Setting):
The serial communication mode (RS232C Mode) is effective.
The GAT3 can be used.
JP4&JP5: The capacity of IC5 (NVRAM) can be selected.
JP4 1-2 CLOSED (ON) and JP5 1-2 CLOSED (ON) (Factory Setting):
The capacity becomes 32KB (M48Z35).
JP4 3-4 CLOSED (ON) and JP5 3-4 CLOSED (ON):
JP4 1-2 CLOSED (ON) and JP5 3-4 OPEN (OFF):
JP6:
CLOSED (ON):
The watchdog timer becomes ineffective.
OPEN (OFF) (Factory Setting):
The watchdog timer becomes effective.
JP7:
JP7: OFF (Factory Setting)
JP7 1-2 CLOSED (ON):
The RS232C mode becomes effective.
The pins 30 and 31 of CN7 can be used.
The current Loop mode becomes effective.
The pins 27 and 28 of CN7 can be used.
4-5
JP8:
CLOSED (ON):
The power save mode becomes ineffective.
OPEN (OFF) (Factory Setting):

The power save mode becomes effective.
SW1 (Push Button):

It is a hardware reset switch, but not used.
SW2 (DIP Switch):
BIT 1:
A CP130 coin acceptor supplied by Money Controls or a MC62
inhibit H coin acceptor supplied by Coin Mechanism Inc. can be used.
ON:
A CP133 coin acceptor supplied by Money Controls or a MC62
inhibit L coin acceptor supplied by Coin Mechanism Inc. can be used.
BIT 2: Reserved.
<LED Indicators>
Two –colored, synchronous LED 1 and LED 2:
Indicates the DOOR I/O PCB is operating normally.
Red light lighted with Green light flashing:
Indicates the DOOR I/O PCB is abnormal.
4-6
4.3 Setting DIP Switch and Jumper Switch on GMEM PCB

S1 Reserved.
JP6: Not Used
S1 backup RAM clear by hardware

ON: Normal
CLEAR: RAM Clear
4-7
<Jumper Switches>
S1 (DIP Switch):
BIT 1: Reserved.
BIT 2: Reserved.
S2 (Slide Switch):
ON (Factory Setting):
Normal.
OFF:
Backup RAM can be cleared by turning OFF when the cabinet is turned
OFF.
JP1:
CLOSED (Factory Setting):
Not Used.
<LED Indicators>
LED1:
Green light: Pilot lamp of +3.3V power (controlled by software)
4-8
4.4 Setting on GMEM Cassette PCB
LED1 Lighted:
Indicates the mother board is accessing to the Compact Flash
[Master/Slave].
4-9
4.5 Setting DIP Switch on AMP PCB
LED indicators
S1: mode setting
N:normal mode(for operating)
W:Test mode/No use
<Jumper Switches>
S1 : mode setting
N : Normal mode(for operating)
W: Test mode/No use
<LED Indicators>
LED1 Red lighted: No sound signal
LED2 Green lighted: Pilot lamp +5V power
LED3 Green lighted: Indicates the GM-FDAMP PCB is operating normally.
4-10
SW6
SW5 Watchdog Timer SW3 SW7
NV-RAM SW Disable SW Serial Sellect SW Battery SW
ON : 8KB ON : Watch Dog Timer Disable
OFF :32KB OFF : Watch Dog Timer Enable ON : Serial 0ch ON : Battry ON
OFF : Serial Programming mode OFF : Battry OFF
4-11
4.6 Setting DIP Switch and Jumper Switch on AUSCOM PCB
<Jumper Switches>
JP1:
Serial data from outside the AUSCOM PCB can be fetched.
JP1 3-4 CLOSED (ON) (Factory Setting):
Serial data from within the AUSCOM PCB can be fetched.
SW3: The internal serial communication port and the program writing port
of Atmel CPU can be selected.
ON (Factory Setting):
The program writing port becomes effective so that programs can be
written into the Atmel CPU.
OFF:
The internal serial port of Atmel CPU becomes effective.
SW4: OFF (Default)

ON: The hardware of AUSCOM PCB can be reset when the system is
locked up.
SW5: The capacity of U4 (NVRAM) can be selected.

The capacity becomes 32KB (M48Z35Y).
ON:
The capacity becomes 2KB (M48Z02Y).
SW6:
ON:
The watchdog timer is disabled
The watchdog timer is enabled.
SW7:
ON (When installed):
The battery for the logic seal is activated to monitor the logic seal
during the time when the machine is OFF.
The battery for logic seal is not activated.
4-12
<LED Indicators>
Two –colored, synchronous LED 1 and LED 11:
Indicates the AUSCOM PCB is operating normally.
Red light lighted with Green light flashing:
Indicates the AUSCOM PCB is abnormal.
LED2 (TxDo):

Indicates that communication data is being output from the AUSCOM
PCB through CN3 (PORT1).
LED3 (RxDo):
Red light flashing:

Indicates that the communication data is being input into the AUSCOM
PCB through CN3 (PORT1).
LED6 (TxD1):

Indicates that communication data is being output from PORT 2, PORT
3, PORT4, PORT5, and PORT 6.
LED4, LED5, LED7, LED8, LED9, and LED10:

Green light lighted:
Indicates that the PORT1, PORT2, PORT3, PORT4, PORT5, and
PORT6 is connected to the external equipment, respectively.
Note:
They lights up when loop back connectors are inserted in PORT1,
PORT2, PORT3, PORT4, PORT5, and PORT6.
4-13
Chapter 5: Test Mode

5.1 Accessing Test Menu
When the game machine is on standby (that is, no game is being played, or there is no tilt
on this machine), you can access the software test menu in the following procedure:
1. Cash out the credits to make the CREDIT meter zero.
2. Open the main door.
3. Turn ON and OFF the RESET keyswitch to display the following screen.
GMID: 0
PROGRAM #: ZANEP003
PROGRAM #: LOSEP003
FIRMWARE #: SMOCX046
DIAGNOSTICS
OUT OF SERVICE
EXIT

5-1
4. Choose “DIAGNOSTICS” by touch.
Otherwise, use the game buttons on control panel..
5. Choose your desired item by touching screen..

Otherwise, use the following CURSOR UP/DOWN, ENTER buttons.
6. To exit to the game mode, touch “EXIT” or press the COLLECT button.
The MAIN MENU shows you GMID, PROGRAM # and FIRMWARE #.
Once in one of the Menus or Sub-Menus, a few commands are available and are
displayed on the Command Line of the screen.
5-2
5.2 DIAGNOSTICS
TEST MODE – DIAGNOSTICS
INPUT TEST
OUTPUT TEST
REEL STRIP / PAY TEST
MONITOR TEST
DIP SWITCH TEST
NOTE ACCEPTOR TEST
EXIT
Various diagnostic and test functions can be performed in Test Mode.

Each Test Mode function is described on the following pages.
5-3
5.2.1 INPUT TEST
TEST MODE - INPUT TEST
RESET KEY :OFF

AUDIT KEY :OFF
POWER SAVE KEY :OFF
RESERVE BUTTON :OFF
COLLECT BUTTON :OFF
GAME RULES BUTTON :OFF
1ST BET BUTTON :OFF
2ND BET BUTTON :OFF
3RD BET BUTTON :OFF
4TH BET BUTTON :OFF
5TH BET BUTTON :OFF
TAKE WIN BUTTON :OFF
1ST LINE BUTTON :OFF
2ND LINE BUTTON :OFF
3RD LINE BUTTON :OFF
4TH LINE BUTTON :OFF
5TH LINE BUTTON :OFF
GAMBLE BUTTON :OFF
COIN IN :OFF
COIN TO CASHBOX :OFF
COIN OUT :OFF
YO-YO ALARM :OFF
HOPPER FULL :OFF
MAIN DOOR :OFF
MAIN DOOR (OPTICAL) :OFF
SECURITY CAGE :OFF
CASH BOX DOOR :OFF
BELLY DOOR :OFF
STACKER DOOR :OFF
MECHANICAL METER DOOR :OFF
DOOR PCB DOOR :OFF
XCOM PCB DOOR :OFF
BODY PCB DOOR :OFF
EXIT
For servicing requirements, switches, buttons and optics can be checked in the INPUT
TEST. As a particular input is activated, “ON” will be displayed if operating correctly.
Note;
These function names may vary depending on game titles.
5-4
5.2.2 OUTPUT TEST
TEST MODE - OUTPUT TEST
RESERVE BUTTON LED :OFF

COLLECT BUTTON LED :OFF
GAME RULES BUTTON LED :OFF
1ST BET BUTTON LED :OFF
2ND BET BUTTON LED :OFF
3RD BET BUTTON LED :OFF
4TH BET BUTTON LED :OFF
5TH BET BUTTON LED :OFF
TAKE WIN BUTTON LED :OFF
1ST LINE BUTTON LED :OFF
2ND LINE BUTTON LED :OFF
3RD LINE BUTTON LED :OFF
4TH LINE BUTTON LED :OFF
5TH LINE BUTTON LED :OFF
GAMBLE BUTTON LED :OFF
COIN LOCKOUT :EJECT
DIVERTER :CASH BOX
BILL INSERT LED 1
BILL INSERT LED 2
COLOR ILLUMINATION(ALL)
COLOR ILLUMINATION(STEP)
WHITE ILLUMINATION (ALL)
WHITE ILLUMINATION (STEP)
EXIT AUTO
The listed lamps, diverter and coin lockout signals can be checked in the
OUTPUT TEST.
Use the BET 1 PER LINE or PLAY 1 LINE button to select your desired
item.
Press the PLAY 25 LINES to perform the output test.
To select “EXIT” or “AUTO”, use the PLAY 9 LINES, BET 3 PER LINE,
and GAMBLE buttons.
By selecting AUTO, each output will be activated in order of the above
screen list.
Note;
These function names may vary depending on game titles.
5-5
5.2.3 REEL STRIP/PAY TEST
TEST MODE – REEL STRIP / PAY TEST
TAKE WIN - SET BET WON BET BET PER LINE

DOUBLE UP - SET LINE
LINE BUTTONS
BET BUTTONS
- MOVE SYMBOLS DOWN
- MOVE SYMBOLS UP
0 1 1
The Symbol Distribution test enables the reel symbol positions in the game
software to be validated. All symbol combinations and pays can be
validated in this test, which includes the pay out for each winning
combination.
To move the symbols for each reel, use the corresponding Bet button and
Play Button. e.g. for reel three (3) use third Bet button (BET 3 PER LINE
button) to progress through the symbols and third Play Button (PLAY 5
LINES button) to go in the opposite direction.
Pressing the GAMBLE button increases the number of lines available and
pressing the Take Win Button increases the credits per line.
To exit and return to the Diagnostics Menu, press the COLLECT button.
Note;
This screen may vary depending on game titles.
5-6
5.2.4 MONITOR TEST

You can test the main LCD module.
TEST MODE – MONITOR TEST
GRID TEST
COLOR TEST
EXIT
GRID TEST
As soon as entering the “GRID TEST”, the following grid test screen appears.
Note:
Adjustment is not available here.
5-7
COLOR TEST
As soon as entering the “COLOR TEST”, the following color test screen is
displayed.
Note:
Adjustment is not available here.
5-8
5.2.5 DIP SWITCH TEST

You can view the current settings of the following DIP switches.
DIP SWITCH TEST
GMEM PCB DIP SW

D1 D2
ON
OFF
DOOR PCB DIP SW

D1 D2
ON
OFF
EXIT
GMEM PCB DIP SW: Refer to Paragraph 4.3 for the details.
DOOR PCB DIP SW: Refer to Paragraph 4.2 for the details.
5-9
5.2.6 NOTE ACCEPTOR TEST

You can test note acceptor.
TEST MODE – NOTE ACCEPTOR TEST
It returns even if note is inserted.

GPT: AU28EB33
NONE
5-10
5.3 OUT OF SERVICE
OUT OF SERVICE
This screen can be selected to place the machine OUT OF SERVICE.

To exit this mode, turn the RESET keyswitch anticlockwise.
5-11
Chapter 6: Preventative Maintenance

This chapter is intended for qualified maintenance/service personnel to show the
preventative maintenance servicing.
WARNING!
Before accessing into the cabinet for servicing, turn off the machine.
Failure to do so could cause an electric shock.
This chapter is intended for qualified maintenance/service personnel to show the

preventative maintenance servicing.
WARNING!
Before accessing into the cabinet for servicing, turn off the machine.
Failure to do so could cause an electric shock.
6-1
6.1 RAM Clear

CAUTION!
Before clearing the RAM, please write down all the necessary data.
Besides the data of the last game and the second last game, all the meters
and settings are cleared, and cannot be retrieved.
Use the following procedure to clear the RAM:

1. Turn OFF the machine.
2. Open the main door and the security cage door.
3. Locate the GMEM PCB in the security cage.
6-2
4. Turn ON and OFF the memory corruption switch on the GMEM PCB.
Memory Corruption Switch
5. Turn ON the machine.
6-3
6. The message of “MEMORY ERROR - RAM CORRUPTED” will appear on the
monitor screen.
Starting ZEARU system

Media Version Number : LOFSMU
System software version number : ZEARU-AN15-0115
Game software version number : Z05058-XXMN-AU-015
Body PCB firmware version number : uYD0B013
Door PCB firmware version number : SPMDB046
Xcom PCB firmware version number : SMOCX046
Last power on :
Last power off :
The current time : 27/03/2007 14:42
Power up self testing

Body PCB communication test [CONNECTED]
Door PCB communication test [CONNECTED]
Xcom PCB communication test [CONNECTED]
EEPROM test [OK]
PROGRAM test [OK]
GAL test [OK]
BODY PCB test [OK]
DOOR PCB test [OK]
GMEM PCB test [OK]
CPU fan test [OK]
SECURITY CAGE fan test [OK]
Backup battery test [OK]
Backup memory test [CRACKED]
Backup version test [OK]
MEMORY ERROR – RAM CORRUPTED
6-4
7. Turn the RESET keyswitch on the machine anti-clockwise – the AUDIT MODE
MAIN MENU will appear on the screen.
GMID: 0
PROGRAM #: ZANEP003
PROGRAM #: LOSEP003
PROGRAM #: SMOCX046
METER INFORMATION TICKET HISTORY
GAME RECALL HOPPER REFILL
MACHINE ERROR LOG

IDENTIFICATION
GAME STATISTICS MACHINE SETUP
EXIT

8. Select the MACHINE SETUP menu.
6-5
9. Select the CONFIGURE / RAM RESET menu.
Note: The main door must be open to perform a RAM reset.
AUDIT MODE – MACHINE SETUP
CONFIGURE
SOUND SYSTEM
TOUCH SCREEN
TICKET PRINT TEST
EXIT
10. To clear the RAM, press the BET 1 PER LINE and TAKE WIN button at the same
time.
6-6
6.2 Maintenance Schedule

The following servicing tasks should be carried out to ensure the reliability of the machine:
6.2.1 Daily Servicing

(1). Clean the machine surface.
CAUTION!
Never use chemical dust cloth, thinner, benzine or alcohol.

They will damage the surface of the machine.
(2). Remove loose coins inside the cabinet.
CAUTION!
A loose coin could cause an unexpected hazard including an electric shock.
(3). Vacuum the inside of the cabinet to remove all dust and debris from the coin chute and
hopper.
(4). Clean the monitor screen with clean, soft cloth. The static electricity gathers dust.
CAUTION!
Never use wet cloth. Do not rub the screen.
6-7
6.2.2 Quarterly Servicing

(1) Inspect the hopper bowl for cracks or breaks, and wipe any dust out of the bowl
with clean, dry cloth.
(2) Inspect the hopper knife and agitator for wear.
(3) Inspect the coin path of the coin acceptor for foreign objects, films, or debris.
If necessary, clean it with clean, dry cloth.
(4) Clean the coin diverter flapper with clean, dry cloth.
(5) Inspect the note channel, exposed drive belt, pressure rollers, etc. of the note
acceptor for foreign objects.
If necessary, clean them with clean, dry cloth.
(6) Inspect every wiring for frayed, cracked, or pinched insulation.
6-8
6.3 Collecting Notes from Note Stacker

When the note stacker gets full, a “NOTE STACKER FULL” error message is displayed
on the main LCD screen.
Use the following procedure to collect notes from the note stacker:
6.3.1 When your note acceptor is an ARGUS note acceptor;
1. Unlock the belly door to open it.

2. Unlock the note acceptor door to open it.
3. When your note acceptor is an ARGUS note acceptor, push up the head cover
over the note stacker.
When your note acceptor is a WBA note acceptor, unlock the note stacker by
pressing down the lock lever on the right side of the stacker.
4. Pull forward the note stacker to take it out.

5. Unlock and open the note stacker door to collect the notes.
6. After collecting the notes, return the note stacker into the note acceptor.
NOTE:
For an ARGUS note acceptor, push down the head cover after setting back the
note stacker.
For a WBA note acceptor, press back the stacker until it snaps locked.
7. Close and lock the note acceptor door.

8. Close the belly door.
9. Turn the RESET keyswitch to clear the error message.
6-9
6.3.2 When your note acceptor is a CashCode note acceptor;
1. Unlock the belly door to open it.

2. Unlock the note acceptor.
3. While pushing the note stacker release lever at the
upper right position of the stacker, withdraw the note
stacker.
4. Turn the note stacker upside down to locate the
stacker open dial.
5. Turn the dial to OPEN to open the stacker.
6. Collect the notes.
7. After collecting the notes, close the stacker door and
lock it.
8. Return the note stacker into the note acceptor.
9. Lock the note acceptor.
11. Turn the RESET keyswitch to clear the error message.
6-10
6.4 Clearing a Stacker Jam Error

If the jam occurred near the entry slot of the note stacker, a “NOTE ACCEPTOR
STACKER JAM” error message is displayed on the monitor screen.
Use the following procedure to clear the jam;
6.4.1 When your note acceptor is an ARGUS note acceptor;
1. Unlock the main door to open it.

2. Unlock the note acceptor door.
3. While pushing up the head cover over the note stacker, withdraw the note stacker.
If necessary, remove the note acceptor head by pushing

outward the note acceptor module lock plate.
4. Clear the jamming note from the entry slot of the

stacker.
5. After clearing the notes, return the note stacker into
the note acceptor.
6. Push down the head cover after setting back the note stacker.
7. Lock the note stacker door.
9. Turn the RESET keyswitch to clear the error
message. Lock Plate
6-11
6.4.2 When your note acceptor is a CashCode note acceptor;
1. Unlock the main door to open it.

2. Unlock the note acceptor.
3. While pushing the note stacker release
lever at the upper right position of
the stacker, withdraw the note stacker.
If necessary, withdraw the note acceptor head

by pulling up the note acceptor head release lever.
4. Clear the jamming note from the entry
slot of the stacker.
5. After clearing the jam, return
the note stacker and the head
to the note acceptor.
NOTE:
When you return the head, be
sure to push it until you hear
a locking sound. Note
6. Lock the note acceptor. Acceptor
head release
7. Close main door. lever
8. Turn the RESET keyswitch to
clear the error message.
6-12
6.5 Disassembly
Refer to our PARTS CATALOG for the fasteners used.
WARNING!
Be sure to turn OFF the power before disassembling.

In the following disassembly procedure, the step of turning OFF the machine
is omitted.
6.5.1 Top Box
6.5.1.1 Escutcheon , Top Glass and Sub-LCD

2. Remove 2 screws at the bottom of escutcheon.
3. Press the side claw hooks, and slightly lift the

escutcheon to remove it.
4. Lift the top glass to remove it from the top glass.
6-13
DANGER!
HIGH VOLTAGE!
NEVER access into the LCD unit. Failure to do so may result in Electric
Shock.
5. Remove 2 screws at the bottom of the monitor unit.
6. Disconnect the monitor cables.
7. Remove the LCD monitor by lifting slightly.
6-14
6.5.1.2 Tower Light (Option)
1. Referring to Paragraphs 6.5.1.1, remove the escutcheon, top glass and the sub-LCD.
2. Disconnect the cable connector and unscrew the tower light in the top box as depicted
below.
3. Pull up the tower light to remove it.
6.5.2 Main Cabinet
6.5.2.1 Security Cage

2. Break the logic seal.
3. Unlock the cage door.
4. Open the cage door.
5. Disconnect all the cable connectors from the security cage.
6. Lift and pull forward the box to take it out.
Logic Seal
6-15
6.5.2.2 Body I/O PCB Housing

1. Locate the Body I/O PCB housing on the left side of the cabinet.
2. Unlock the Body I/O PCB housing by using a key.
3. Lift down (unhook) the housing.
4. Disconnect the cable connector.
Key lock
6.5.2.3 AUSCOM PCB Housing

1. Locate the AUSCOM PCB housing on the cabinet.
2. Unlock the AUSCOM PCB housing by using a key.
3. Lift down (unhook) the housing.
Key lock
6-16
6.5.2.4 Hopper
2. Pull forward the hopper to remove it.
6.5.2.5 Woofer and Speakers

When you need to remove the woofer and speakers, contact ARUZE or your nearest
distributor.
6-17
6.5.3 Main Door
6.5.3.1 Door I/O PCB Housing

2. Locate the Door I/O PCB housing on the back of the main door.
3. Untie the cables on the PCB housing to set them aside.
3. Unscrew the PCB housing (1 screw).
4. Open the housing as depicted below.
6.5.3.2 Main LCD Unit

DANGER!
HIGH VOLTAGE!
NEVER access into the LCD unit. Failure to do so may result in Electric
Shock.

2. Locate the main LCD unit on the back of the main door.
3. Disconnect the cable connectors.
4. Unscrew the main LCD unit (4 screws)
6-18
6.5.3.3 Note Entry Assembly

2. Locate the note entry assembly on the back of the
main door.
3. Unscrew the note entry assembly (1 screw).
6.5.3.4 Game Control Panel

2. Disconnect all the cable connectors from the game buttons.
3. Unscrew the game control panel fixing screws (3 screws).
4. On the front of the main door, lift and pull the game control panel forward to
remove it.
6.5.3.5 Game Button
1. Remove the game control panel as described in Paragraph 6.5.3.4.

2. Turn the control panel upside down.
3. Unscrew the game button to remove it.
6-19
6.5.3.6 Common Button
1. Open the Belly Door.

2. Pinch a Common Button from under the panel.
3. Remove the lower part of button by turning.
4. To remove the upper part, pinch the claw of button and push upward.
6.5.4 Belly Door
6.5.4.1 Belly Door Glass Lamp Assembly
1. Open the belly door.

2. Disconnect the cable connector from the lamp assembly.
3. Unscrew the assembly (2 screws) to remove it.
6.5.4.2 Belly Door Glass

1. Remove the belly door glass lamp assembly as described in Paragraph 6.5.4.1.
2. Detach the belly door glass.
6-20
6.6 Replacement
6.6.1 Lamps and Fluorescent Lamps
WARNING!
Turn OFF the machine before replacing a lamp.

The lamps and fluorescent lamps may be hot.
Wait until they cool down before touching them.
Any replacement lamp must be the one specified by ARUZE, or the
equivalent.
6.6.1.1 Lamps of Optional Tower Light (Candle)

1. Referring to Paragraph 6.5.1.2, remove the tower Screw
light.
2. Loosen the screw on the top of the tower light to
separate the tiers.
3. Unscrew the old lamp to replace it with a new
one.
4. In the reverse order of the above, reassemble the
tower light.
5. Return the tower light onto the top box.
6. Return the sub-LCD, the escutcheon, the top glass
and game name strip bracket.
6-21
6.6.1.2 Fluorescent Light for Belly Glass

1. Referring to Paragraph 6.5.4.1, remove the fluorescent light assembly for the belly
glass.
2. Turn the light assembly upside down to locate the fluorescent light release tabs.
3. Holding the fluorescent light by one hand, press one of the tabs outward.
4. Pull up (or forward) the fluorescent light until the terminal releases from the
socket.
5. Replace the light with a new one.
6. Return the light assembly onto the belly Fluorescent light release tab
door.
NOTE:
When your machine is single-LCD type,
tighten the belly door fixing screws.
6.6.1.3 Fuse
2. Locate the fuse holder just above the POWER switch.
3. Push the fuse holder, then turn it counterclockwise to remove it.
4. Pull out the fuse to replace it with a new one.
5. Return the fuse holder onto the power box.
NOTE:
If a specified fuse is easily blown,
contact ARUZE or your nearest
distributor.
6-22
6.6.2 Lithium Battery
A lithium battery is mounted on the main, GMEM, Body I/O, and Door I/O PCB’s
to back up the important data. The procedure to replace the lithium batteries is
outlined below:
WARNING!
Use a specified lithium battery or the equivalent.

Failure to do so may result in an accident or a fire.
Before mounting a lithium battery, verify its polarity. Mounting the

battery in the wrong direction may damage the PCB’s.
Waste lithium batteries must be disposed as instructed.

Refer to SAFETY INSTRUCTION, “Disposal of Lithium Batteries”.
6-23
6.6.2.1 Replacing Lithium Batteries in Security Cage

Replace the lithium battery in the security cage in the following procedure:
CAUTION!
Before replacing the lithium batteries, please write down all the necessary
data. The replacement after POWER-OFF may delete the data.

3. Unlock the security cage.
4. Referring to Paragraph 6.5.2.1, withdraw the security cage to take it out.
5. Referring to Paragraph 1.2, “Security Cage”, locate a lithium battery on Mother Board
and GMEM PCB.
NOTE:
If necessary, unscrew the PCB’s fixing plate
(1 screw) to remove it.
6. To replace the lithium battery on the Mother
Board;
(1) Locate the battery lock.
(2) Lifting the battery lock, pull out the old
battery to replace it with the new one.
To replace the battery on the GMEM PCB;

(1) Pull out the battery.
7. Return the security cage into the main cabinet.
8. Lock the cage.
9. Connect the cable connectors to the cage.
10. Turn ON the machine, and close and the main
door.
6-24
6.6.2.2 Replacing Lithium Battery on Body I/O PCB

3. Referring to Paragraph 6.5.2.2, unscrew the PCB housing.
4. Locate the lithium battery on the Body I/O PCB.
5. Set the jumper switch to Battery OFF position.
Note:
When you wish to clear the security cage status, set the jumper switch (SW2
Bit2) to Battery OFF position.
6. Pull out the old battery to replace it with the new one.
7. After the replacement, set the jumper switch back to Battery ON position.
8. Screw down the PCB assembly onto the cabinet.
9. Turn On the machine.
Lithium Battery
6-25
6.6.2.3 Replacing Lithium Battery on Door I/O PCB

3. Referring to Paragraph 6.5.3.1, unscrew the Door I/O PCB housing.
4. Locate the lithium battery on the PCB.
8. Screw down the PCB assembly onto the back of the main door.
Lithium Battery
6-26
6.6.2.4 Replacing Lithium Battery on AUSCOM PCB

2. Make sure that the power is OFF.
3. Referring to Paragraph 6.5.2.3, unlock the AUSCOM PCB housing to open the
cover.
4. Locate the lithium battery on the PCB.
8. Close the PCB cover and lock the housing.
9. Return the hopper and the printer.
11. Close the main door
Lithium Battery
6-27
6.7 Adjustment
6.7.1 Sensitivity of CONDOR Coin Acceptor
When your coin acceptor is a CONDOR coin acceptor, the sensitivity can be adjusted in the
following procedure:

2. Locate the coin acceptor on the back of the main door.
3. With the cable connected to the coin acceptor, push up then pull forward the
coin acceptor to remove it.
4. Adjust the sensitivity using the rotary switch at the lower right position of the
coin acceptor.
a. For the standard sensitivity, set the rotary switch to “0” position with a
small blade screwdriver.
b. To increase the selectivity for your coinage, turn the rotary switch
counterclockwise.
c. To increase the rejectivity against slugs, turn the rotary switch
clockwise.
5. Return the coin acceptor onto the back of the main door.
6. Close the main door to check the selectivity/rejectivity by inserting proper
coin and/or high quality slugs.
7. Repeat the above steps 4 through 6 as necessary to get the finest adjustment.
6-28
6.7.2 Note Entry Level
Use the following procedure to adjust the level of note entry.

2. Remove the hopper.
3. Loosen the 3 screws that are fixing the note acceptor to the cradle.
4. Loosen the nut under the note acceptor, which is fixing the level adjusting knob.
5. Turn the knob clockwise to raise the note entry. Turn the knob counterclockwise
to lower the note entry.
6. After adjusting, tighten the 3 screws and the nut.
7 Return the hopper and close the main door.
Nut
Level adjusting knob
6-29
6.8 Changing Game

When you want to change the game, you have to receive a GMEM Cassette from ARUZE.
The GMEM Cassette consists of
Compact Flash
GAL
NOTE:
The contents of the GMEM Cassette vary according to your current game.
6.8.1 Changing GMEM Cassette

Use the following procedure to change the game software.
1. Open the main door to turn OFF the machine.

2. Unlock the security cage door.
3. Unscrew the cassette screw, pull out the cassette.
4. Replace the GMEM Cassette.
GMEM Cassette
6-30
GMEM Cassette
GMEM Cassette Cover (L)
Cassette Screw
GMEM Cassette PCB
Compact Flash GAL socket

socket (Slave)
Compact Flash socket

(Master)
Cassette Screw
GMEM Cassette Cover

(R)
6-31
Chapter 7: Troubleshooting
This chapter is intended for qualified maintenance/service personnel to show the troubleshooting.
WARNING!
Turn OFF the machine before accessing into the cabinet.
7-1
7.1 Hopper Errors
HOPPER OVERPAY - EXCESS PAYOUT
Check the hopper wiring for loose, frayed, cracked, or disconnected wires.
Check if the CN13 connector of the Body I/O PCB is firmly seated.
Check if the harness is damage.
Turn the RESET keyswitch.
YES
Has the error
been cleared?
NO
Adjust the payout sensor.
Does the hopper YES

normally payout coins in
HOPPER TEST?
NO
Replace the hopper.

YES
Has the error
been cleared?
NO
Replace the Body I/O PCB.

Turn the REST keyswitch.
Does the hopper YES

HOPPER TEST?
NO
Contact ARUZE or your nearest distributor. END
7-2
HOPPER JAM
Check the coin-out path for a coin jam.

Check if the hopper knife is shifted (GM hopper).
YES
Has the error
been cleared?
NO
Test the payout sensor in INPUT test.
YES Does the payout

sensor normally
work?
NO
Check the payout sensor wiring for loose, frayed, cracked, or disconnected wires.
Check if the harness is damaged.
Does the hopper YES

normally payout coin in
HOPPER TEST?
NO
Adjust the payout sensor.
Does the hopper YES

HOPPER TEST?
NO
Replace the hopper.

Has the error YES

been cleared?
NO
Does the hopper YES

HOPPER TEST?
NO
7-3
COIN OUT ERROR-HOPPER EMPTY
Are there coins in the hopper bucket?

If there is not, replenish coins.
YES
Has the error
been cleared?
NO
Test the payout sensor in INPUT test.
YES Does the payout

sensor normally
work?
NO
Replace the payout sensor.
Does the hopper YES

HOPPER TEST?
NO
Replace the hopper.

Has the error YES

been cleared?
NO

Does the hopper YES

HOPPER TEST?
NO
7-4
HOPPER DISCONNECTED
Check the hopper wiring for loose, frayed, cracked, or disconnected wires.
Has the error YES

been cleared?
NO
Replace the hopper.

Has the error YES

been cleared?
NO

YES
Has the error
been cleared?
NO
7-5
7.2 Coin Acceptor Errors
COIN ERROR
A coin was inappropriately inserted.

The coin diverter malfunctioned.
Perform the OUTPUT TEST of the

diverter by calling AUDIT mode.
YES
Is the diverter normally
working?
NO
Replace the diverter.
YES
working?
NO
NO
Replace the Door I/O PCB.
YES
working?
NO
7-6
COIN-IN JAM
Check the coin acceptor for a coin jam or foreign material

blocking the sensor. Turn the RESET keyswitch
YES
Has the error
been cleared?
NO
Check the coin acceptor wiring for loose, frayed, cracked, or disconnected wires.
Check if the CN7 connector of the door I/O PCB is firmly seated.
YES
Has the error
been cleared?
NO
Replace the coin acceptor.
Has the error YES

been cleared?
NO
Check the voltages (5V, 12V, and 24V) of the door I/O PCB?
Has the error YES

been cleared?
NO
Replace the door I/O PCB.
Has the error YE

been cleared?
NO
7-7
COIN-IN YO-YO
YES
Has the error
been cleared?
NO
YES
Has the error
been cleared?
NO
YES
Has the error
been cleared?
NO
YES
Has the error
been cleared?
NO

Has the error YES

been cleared?
NO
END
Contact ARUZE or your nearest distributor.
7-8
COIN ACCEPTOR ERROR
YES
Has the error
been cleared?
NO
YES
Has the error
been cleared?
NO
YES
Has the error
been cleared?
NO
YES
Has the error
been cleared?
NO

Has the error YES

been cleared?
NO
7-9
DIVERTER FAULT
YES
Is there a coin jam in Clear the coin jam.
the drop chute? Turn the RESET keyswitch.
NO
YES
Does the diverter Has the error
YES
operate normally in been cleared?
OUTPUT test?
NO
NO Does the drop sensor
operate normally in
YES INPUT test?
NO
Check the diverter solenoid wiring for loose, frayed, cracked, or

disconnected wires.
Check the voltages (5V, 12V, and 24V) of the door I/O PCB.
Check the diverter sensor wiring for loose, frayed, cracked,

or disconnected wires. Check the CN7 connector of the
YES Door I/O PCB is firmly seated. Check if the harness is
Has the error
damaged. Check the voltages (5V, 12V, and 24V) of the
been cleared?
Door I/O PCB.
NO
Replace the diverter solenoid. Has the error YES

Turn the RESET keyswitch. been cleared?
NO
YES
Has the error
been cleared? Replace the drop sensor.
Turn the RESET keyswitch
NO

YES
Has the error
been cleared?
END
NO
7-10
7.3 Note Acceptor Errors
NOTE ACCEPTOR STACKER JAM
Check for a note jam or foreign material blocking the note sensor.
Has the error YES

been cleared?
NO
Replace the note stacker.

YES
Has the error
been cleared?
NO
NOTE ACCEPTOR JAM
Check for a note jam or foreign material blocking the note sensor.
Has the error YES

been cleared?
NO
Has the error YES

been cleared?
NO
END
7-11
NOTE ACCEPTOR STACKER REMOVED
Check if the note stacker has been removed.

Set the note stacker correctly
Has the error YES

been cleared?
NO
Has the error YES

been cleared?
NO
END
NOTE ACCEPTOR STACKER FULL
Collect notes from the note stacker.
YES
Has the error
been cleared?
NO
Replace the note stacker
YES
Has the error
been cleared?
NO
END
7-12
NOTE ACCEPTOR DISCONNECTED
Check if the note acceptor module is firmly set on the

note acceptor.
Has the error YES

been cleared?
NO
Check the note acceptor wiring for loose, frayed, cracked, or disconnected
wires.
Check if the harness is damage.
Has the error YES

been cleared?
NO
NOTE 1
Replace the body I/O
PCB.
Has the error YES

been cleared?
NO
END
7-13
NOTE ACCEPTOR FAILURE
The note acceptor malfunctioned or is out of work.

YES
Has the error been cleared?
NO
Check that the connector of the note acceptor is securely seated.
Check that the CN8 of the Body I/O PCB is securely seated.
Check that there is no disconnection on the harness.
Has the error been YES

cleared?
NO
Replace the Body I/O See NOTE.

PCB.
YES
Has the error been
cleared?
NO
NOTE：
Set the jumpers of the BODY I/O PCB as shown below:
GPT bill acceptor:
Jumper "3-4" of JP3 and JP4
Jumper JP8 to "G".
JCM bill acceptor:

Jumper "3-4" of JP3 and JP4
Jumper JP8 to "G".
7-14
7.4 Ticket Printer Errors
TICKET PRINTER PAPER LOW
Ticket paper is running short.

Referring to our Operation Manual,
Paragraph 4.8, load tickets into the ticket
supply tray.
Turn the RESET keyswitch to clear the

error message.
END
TICKET PRINTER PAPER JAM

TICKET PRINTER PAPER EMPTY
Ticket paper is depleted. A paper jam occurred in the ticket printer.

Referring to our Operation Manual,
Paragraph 4.8, load tickets into the ticket Referring to our Operation Manual,
supply tray. Paragraph 4.8, clear the jam.
Turn the RESET keyswitch to clear the

error message. Turn the RESET keyswitch to clear the
error message.
END
END
7-15
TICKET PRINTER OPEN
The ticket cover of the printer is opened.

Close the ticket cover, and turn the
RESET keyswitch to clear the error
message.
END
TICKET PRINTER DISCONNECT
The ticket printer is disconnected.

Check 14 pin connector on the back
of the printer
YES YES
Is the 14 pin connector Is the CN24of the Body I/O PCB
connect properly? is properly connected?
NO NO
Connect the 14 pin connector properly. Connect the CN24 properly.

Turn the RESET keyswitch to clear the Turn the RESET keyswitch to clear the
error. error.
YES
YES
Is the error Is the error
cleared? cleared?
NO NO
END
7-16
7.5 Mechanical Meter Errors
METER CONNECTED-#*
Note:
The meters #1 to #5 are arranged from left to right.
Check the mechanical meter wiring for loose, frayed, cracked, or

disconnected wires.
Check if the "CN11" connector is securely seated?
Check if the voltage of the Door I/O PCB is 5V, 12V, and 24V.
Has the error YES

been cleared?
NO
Replace Meter#*.
YES
Has the error
been cleared?
NO

Return the RESET keyswitch.
YES
Has the error
been cleared?
NO
END
7-17
7.6 Backup Battery Errors
BACKUP BATTERY FAIL-GMEM BOARD
Take out the security cage, and replace the backup battery on the GMEM
PCB.
YES
Has the error
been cleared?
NO
Check if the three LED's on the security cage are normally lit.
Check if the power supply cable of the main security cage is securely
seated.
Check if the GMEM PCB is securely seated in the PCI socket of the
mother board.
YES
Has the error
been cleared?
NO
Replace the GMEM PCB.

Clear the RAM.
YES
Has the error
been cleared?
NO
7-18
BACKUP BATTERY FAIL -BODY PCB BOARD
Remove the Body I/O PCB housing, and replace

the backup battery on the Body I/O PCB.
YES
Has the error
been cleared?
NO
Check if the voltages of Body I/O PCB are 5V, 12V, and
24V.
Check if Bit1 and Bit2 of SW1 is turned ON.
YES
Has the error
been cleared?
NO

YES
Has the error
been cleared?
NO
7-19
BACKUP BATTERY FAIL -DOOR PCB BOARD
Remove the Door I/O PCB housing, and replace

the backup battery on the Door I/O PCB.
YES
Has the error
been cleared?
NO
Check if the voltages of Door I/O PCB are 5V, 12V, and 24V.
Check if JP1 is securely jumpered to ON.
YES
Has the error
been cleared?
NO

YES
Has the error
been cleared?
NO
7-20
7.7 System Errors
MEDIA REMOVED DURING POWER DOWN
Did you replace YES

the compact flash?
NO
The compact flash memory may be Clear the RAM to

illegally changed. perform the settings.
IDE DISCONNECT DURING POWER DOWN
YES
Did you disconnect the IDE

cable during power down?
NO
There is a possibility that the security

cage was illegally accessed.
Clear the RAM and configure the machine.

END
7-21
XCOM I/O ERROR
Clear the RAM.
YES
Has the error been
cleared?
NO
With the machine ON, look into the AUSCOM security

cage from the front hole to check if the AUSCOM PCB
indicator LED is blinking.
YES
Is the green or red
LED blinking?
NO
Check if the USB cable is securely connected YES

between the mother board and the AUSCOM Are there voltages of 5V,
PCB. Check if the USB cable is disconnected. 12V, and 24V on the PCB?.
NO
Perform the continuity test of

the power harness.
Turn ON the machine and then

turn the RESET keyswitch.
YES
Has the error been
cleared?
NO
Replace the AUSCOM PCB.
Turn ON the machine and then

turn the RESET keyswitch.
YES
Has the error been
cleared?
NO

END
7-22
SELF AUDIT ERROR
The soft meters failed in the self audit check.

Clear the RAM.
YES
NO
Check if the GMEM PCB is securely connected to the Mother Board.

Check if the CF (compact flash memory) or GAL is securely seated on the GMEM
Cassette PCB.
Clear the RAM.
YES
NO
Replace the GMEM PCB and GMEM

Cassette PCB.
Clear the RAM.
YES
NO
END
7-23
GMEM PCB READ ERROR
The GMEM PCB could not be read.

Correctly set the GMEM PCB.
YES
NO
Check if the GMEM PCB is securely connected to the PC mother board.

Check if the CF (compact flash memory) or GAL is securely seated on the GMEM
Cassette PCB.
Clear the RAM
YES
NO

Cassette PCB.
Clear the RAM
YES
NO
7-24
CPU FAN ERROR
With the machine ON, slightly pull the security cage

forward to check if the fan is normally working.
YES
Is the fan working?
NO
Turn OFF the machine, and withdraw the security cage to

check if the CPU fan connector is firmly seated.
Turn ON the machine.
YES
Has the error
been cleared?
NO
Replace the fan.

Has the error YES

been cleared?
NO
Replace the mother board.

YES
Has the error
been cleared?
NO

When the mother board is replaced, set the
date and time by calling Audit Mode.
7-25
SECURITY CAGE FAN ERROR
With the machine ON, place your hand on the top surface of the security cage just
above the fan to check if the fan is normally working.
YES
Is the fan working?
NO
Turn OFF the machine, and withdraw the security cage to

check if the security cage fan connector is firmly seated.
YES
Has the error
been cleared?
NO
Replace the fan.

YES
Has the error been
cleared?
NO
Replace the mother board.

YES
Has the error
been cleared?
NO

When the mother board is replaced,
set the date and time by calling Audit
Mode.
7-26
CAN NOT OPEN EEPROM
The EEPROM-1 (U10) on the GMEM PCB could not be read.

Correctly set the EEPROM-1 (U10).
YES
NO
Check if the GMEM PCB is securely connected to the mother board.

Clear the RAM.
YES
NO

Cassette PCB.
Clear the RAM.
YES
NO
7-27
CAN NOT OPEN SECONDLY EEPROM
The EEPROM-1 (U24) on the GMEM PCB could not be read.

Correctly set the EEPROM-1 (U24).
YES
NO
Check if the GMEM PCB is securely connected to the mother board.

Clear the RAM.
YES
NO
Clear the RAM.
YES
NO
7-28
CAN NOT OPEN GAME SELECT CHIP
The GAL (U1) on the GMEM_Cassette PCB could not be read.

Set the GAL (U1) correctly.
YES
NO
Check if the GMEM PCB is securely connected to the PC mother board.

Clear the RAM.
YES
NO
Clear the RAM.
YES
NO
7-29
BODY PCB SRAM ERROR
The Body I/O PCB failed in the check of SRAM (IC16/IC41) when starting up the
machine.
YES
NO
Clear the RAM
YES
NO
7-30
DOOR PCB SRAM ERROR
The Door I/O PCB failed in the check of SRAM (IC5) when starting up the machine.
The memory corrupted. Clear the RAM.
YES
NO
Clear the RAM
YES
NO
7-31
Chapter 8: Machine Specifications
This chapter shows the machine specifications.
8.1 Cabinet Name

GENX-WD00
8.2 Overall Dimension Including Tower Light

- When 2 tiers tower light is attached.
624 (width) x 1534 (height) x 588 (depth) mm
- When 3 tiers tower light is attached.

624 (width) x 1579 (height) x 588 (depth) mm
8.3 Weight
128 Kg (including 10 Kg transformer and 7 Kg reel unit)
8.4 Electrical Specifications

When Line Voltage is 220 through 240 VAC
Line frequency: 50Hz
Max. current draw during game play: 3.6A
When Line Voltage is 100 through 120VAC

Line frequency: 60Hz
Max. current draw during game play: 5.5A
Fuse: 6.3A
Fluorescent lamp: 15W
Outlet: Earthed power outlet
8-1
8.5 Environment
Ambient temperature: 0 through 40 degrees C
Ambient humidity: 5 through 95%
Free from dew condensation
8.6 Coins/Notes Capacity

Hopper
About 1100 coins (Aus. $1)
About 450 coins (US$ 1.00)

About 1800 coins (US 25 cent)
About 1600 coins (1R)

About 600 coins (10R)
Note stacker
ARGUS Note Stacker: About 500 notes
CashCode Note Stacker: About 600 notes
8-2
Chapter 9: Parts Catalog
MAJOR COMPONENTS
9-1
No. 1 TOP BOX ASSEMBLY
9-2
TOP BOX ASSEMBLY (PARTS LIST)

ITEM PART NO. PARTS NAME Q’TY MATERIAL/TYPE REMARKS
1 MEX-343-00 ENEX TB SIDE REF L FRONT 1 ABS
2 MEX-344-00 ENEX TB SIDE REF L REAR 1 ABS
3 MEX-345-00 ENEX TB SIDE REF FRAME L 1 SECC t=1.2
4 BD-GM-M2LED4 2
5 ML2-525-00 ML2 TB LED PCB BKT 2 SECC t=1.2
6 ML2-515-00 ML2 TB 19IN UPPER SPONGE 2 CR 360x4 t=1.0
7 MEX-310-00 ASSY SUB ENEX TB 1
8 TOWER LIGHT 1 TWL2-12V By customer’s demand.
9 0C0022800 TOP TOWER HOLE BLIND PLATE 1 SECC-C t=1.0
10 TOWER LIGHT 1 TWL3-12V By customer’s demand.
11 G-TOPPER 1 GTPR-PP By customer’s demand
12 MEX-347-00 ENEX TB SIDE REF R FRONT 1 ABS
13 MEX-349-00 ENEX TB SIDE REF FRAME R 1 SECC t=1.2
14 MEX-348-00 ENEX TB SIDE REF FRAME R 1 ABS
15 ML2-034-00 ML2 TB TOP GLASS 1 t=5.0
16 ONE TOUCH BUSH 2 NB-8
17 ML2-408-00 19IN LCD CASE ASM 1
18 ML2-418-00 19IN LCD ADJ COVER 1 SECC t=1.2
19 ML2-419-00 19IN LCD REAR COVER ASM 1
20 ML2-183-00 19IN INSURATION SHEET 1 PC t=0.5
21 2D4106400 LCD RUBBER 4 EPM
22 19IN LCD 1 Model Name: LM190E03
Manufacturer: LG.PHILIPS LCD

23 ML2-163-00 MONITOR MASK 19 ASM 1
24 MEX-341-00 ENEX TB 19 ESC UPPER BKT 1 SECC t=1.2
25 ML2-505-00 ML2 TB 19 ESC LOWER BKT 1 SECC t=1.2
26 ML2-489-00 MONITOR MASK LED LENS 2
27 609926100 DVI/RGB to LVDS PCB SC-3B 1 SC-3B Manufacturer: COLCOAT
28 602426000 LCD BACKLIGHT INVERTER IM6501 1 IM6501 Manufacturer: MNB
29 2EK006800 ST W HIGH VOLTAGE UL 1 PET t=0.75
30 810346200 CLAMP 1 EMT-6N
9-3
No. 2 CABINET ASSEMBLY (1/2)
9-4
CABINET ASSEMBLY 1/2 (PARTS LIST)

1 MEX-501-00 ASSY ENEX SUB CABI AUS 1

2 No.13, No.14 HOPPER ASSEMBLY 1 Model Number: GM-HOPPER
Manufacturer: ARUZE GAMING AMERICA, INC.
3 Refer to No.5 NOTE ACCEPTOR (CASHCODE) 1 Model Number: FL-0510
Manufacturer: CashCode Company Inc
Firmware: FL-AU2218
Refer to No.6 NOTE ACCEPTOR (GTP) Model Number: SA-4, 304X331121G
Manufacturer: GPT
Firmware: AU28EB33
4 SWITCHING POWER SUPPLY 1 Model Number: A2PSAPSU2G04 / A2PSAPSU2G07
Manufacturer: TEGA SANYO KOUGYO CORPORATION
5 ML2-604-00 ASSY ML2 CB KYE PLATE 1
6 ML2-605-00 ML2 BILL SPACER TABLE BRKT 1 SECC t=1.6
7 ML2-606-00 ML2 CB HOPPER BASE ASM 1
8 ML2-619-00 ML2 CABI BOTTOM WOOD 01 1 t=18

9 ML2-647-00 HEAT INSULATOR 1 SECC t=1.2
10 ML2-611-00 ML2 CB PRINTER BASE 1 SECC t=1.2
11 0D4014200 LOCK SLIDER COLLAR 4 C3601BDφ=10
12 0D4008400 MAIN DOOR SW BKT 1 SECC-C t=1.2
13 0D4006600 PCB BOX SW BKT 1 SECC-C t=1.2

14 0D4007000 MAIN DOOR KEY PLATE 1 SECC-C t=2.3
15 KEY SW LABEL 2 PC t=0.5
16 TICKET PRINTER 1 Model Name: Ithaca EPIC950
Manufacturer: Transact Technologies, Inc.
Firmware: S00122
17 601356400 KEY SW 1 KG3C-20D ASSY Varies according to spec.
18 ML2-623-00 ML2 SPEAKER BORD 01 1 MDF t=12

19 SPEAKER 1 FL160U132-1
20 ML2 CB UPPER HINGE PLATE ASM 1
21 ML2 CB LOWER HINGE PLATE ASM 1
22 SPACER 1 CC-0816-10
23 WASHER 1 NN-0816-10
24 ML2-603-00 ML2 DROP CHOUTE ASM 1
25 600138000 DOOR SWITCH 3 SDKNA20600
26 DC FAN 2 109R0812S401
27 SENSOR 1 KB875-AZ02LF
9-5
CABINET ASSEMBLY (1/2) (PARTS LIST)

28 601306201 SHORT DOOR LOOK (2155) 1 GSK-501SB2155 (Key way: left)

29 600894700 FINGER GUARD 2 109-049E
30 2C0005600 NYLON WASHER 4 CC-0612-05
31 ML2 DR DOOR STOPPER 1 SGD φ8
32 3382309-50115 SPACER 1
33 SPRING 1 E-593
34 ML2-658-00 MAIN POWER SW BOX 1 SECC t=1.2
35 LOCKER SWITCH 1 AJ8202BF
36 MEX-114-00 KEY SW HOLE BLIND PLATE ASM (B) 1
37 TP POWER BOX COVER 1 TPA-4004
38 SWITCHING POWER SUPPLY 1 Model Name: ZWS75AF-24/J
Manufacturer: DENSEI-LAMBDA
39 0D4114200 BLIND PLATE WASHER 1
40 2D40EAN00 POWER SAVE SW LABEL (1) Varies according to spec.
41 601367000 POWER SAVE KEY SW (1) KH2C-10A ASSY
9-6
No. 3 CABINET ASSEMBLY (2/2)
9-7
CABINET ASSEMBLY (2/2) (PARTS LIST)

1 MEX-505-00 BODY IO CASE AUS 1
2 DOOR SWITCH 1(2) SDKNA20600 Varies according to spec.
3 CEK000200 BD-GM-M2IO 1 P509002-0303TI
4 MEX-506-00 BODY IO COVER AUS 1 Varies according to spec.
5 S411668 2 Varies according to spec.
6 KEY2155 2 Varies according to spec.
7 ML2-420-00 ML2 DR BLY KEY PLT 2 Varies according to spec.
8 MEX-509-00 AUSCOM COVER 1 Varies according to spec.
9 CD4018A00A AUSCOM-A PCB 1 Model Name: FR-4/UA2054-11A
Manufacturer: ARUZE GAMING AMERICA INC.
10 810338100 EDGING SADDLE 6 TSB-1909L Varies according to spec.
11 MEX-508-00 AUSCOM CASE 1 Varies according to spec.
12 MEX-133-00 BODY IO COVER 1
13 Refer to No.4 PC BOX 1 Model Name: AP-7
14 MEX-511-00 POWER PORT BRKT 1 Varies according to spec.
15 600614300 CIRCUIT BREAKER 6 106-P10-0.5A Varies according to spec.
16 0EK014800 TRANS BOX ASM 1 SECC Varies according to spec.
17 ST W HIGH VOLTAGE UL 1 PET t=0.75 Varies according to spec.
18 TRANS INPUT AC 115V (1) 600746200 Varies according to spec.
19 601403400 INLET 1 AC-P03CS05 Varies according to spec.
20 601403200 OUTLET 1 AC-F01FB01 Varies according to spec.
21 601515400 FUSE HOLDER KNOB 2 3455LF1-020 Varies according to spec.
22 FUSE 1 215 001.P Varies according to spec.
23 601515000 FUSE HOLDER 2 3453LF2-010 Varies according to spec.
24 MAIN FUSE LABEL 1 Varies according to spec.
25 UNSWITCHD FUSE LABEL 1 Varies according to spec.
26 INLET LABEL 1 Varies according to spec.
27 OUTLET LABEL 1 Varies according to spec.
28 FUSE (1) 215 012.P Varies according to spec.
29 810338200 EDGING SADDLE 2 TSB-3027
30 FUSE (1) 215 010.P Varies according to spec.
31 TRANS INPUT AC220V (1) 600746300 Varies according to spec.
9-8
No. 4 PC BOX AP-7
9-9
PC BOX AP-7 (PARTS LIST)

1 603537200 MOTHER BOARD AP-7 1 AP-7 Manufacturer: ALBATRON
2 M311042 MOTHER INSULATION SPACER 1
3 600138000 DOOR SW 1 SDKNA20600
4 ABE1-0051 POLY BUSH 2
5 ABE1-0045 AP7 PC SW BRKT 1
6 POLY WASHER 2
7 SPRING 1 E577
8 ABE1-0049 AP7 PC SW GUIDE FRONT 1
9 ABE1-0050 AP7 PC SW GUIDE REAR 1
10 LOCKING ADJUST CLAMP 1 LCT-4Si
11 ABE1-0055 AP7 CONNECTOR COVER G 1
12 KEY CYLINDER 1 F750-MSDS-L90
13 ABE1-0038 AP7 PC FRONT COVER 1
14 HINGE 2 LSB-50
15 ABE1-0043 AP7 PC KEY PLATE 1
16 ASSY GMEM CASSETTE 1
17 ABE1-0036 AP7 PC BASE 1
18 PC2-2000 ASSY AP-7 GMEM2 1 P509012-0202HK-02
19 ABE1-0047 AP7 PC SLOT COVER 1
20 603537400 GRAPHIC BOARD 7600GS 1 9GP76GSQ-R00-10BH1 Manufacturer: ALBATRON
21 DC FAN 1 9G0812H105
22 CEK002700 BD-GM-FDAMP 1 P509001-0303SK
23 ABE1-0044 AP7 PC FIX BRKT 1
24 ABE1-0058 AP7 SPONGE 2
25 ABE1-0037 AP7 PC FRONT PANEL 1
26 AP7 I/O PANEL 1
27 CEK002800 BD-STH 1 P611101-0101KT
28 CPU 1 BX80552352(D0-)
29 603537500 MEMORY DDR2 ARF5300K-512 2 ARF5300K-512 Manufacturer: Adtec
30 LOCKING PCB SPACER 6 LCBT-3S
31 LOCKING ADJUST CLAMP 2 LCT-2.5S
32 LOCKING ADJUST CLAMP 2 LCT-2S
9-10
No. 5 NOTE ACCEPTOR (CASHCODE BV (600) ASSEMBLY)
9-11
CASHCODE BV (600) ASSEMBLY (PARTS LIST)

1 0D4008600 BV ACTUATOR SPRING (JCM) 1 SWP φ0.5
2 ST W AVOID INJURY UL 1 PET t=0.75
3 ML2-659-00 BV ADJUST BKT W 1 SECC-C 2.0t
4 0D4009200 BV CASE (JCM) 1 SECC-C 1.2t
5 0D4021600 BV STACKER DOOR (Cash Code) 1 SECC-C 1.2t
6 0D4021400 BV STACKER RAIL (Cash Code) 1 SECC-C 1.2t
7 0D4009800 BV ACTUATOR (JCM) 1 SECC-C 1.2t
8 0D4010000 BV SW BKT (JCM) 1 SECC-C 1.2t
9 0D4010200 BV ACTUATOR PIN (JCM) 1 SUS 304 φ3

10 VALIDATING HEAD MFLV-2110
11 BEZEL 1 MFLB-2401
12 HOUSING 1 FLH-0110
13 POWER INTERFACE 1 FLP-1710
14 CASSETTE 1 FLC-103
15 600121000 SAFETY DOOR SW 1 E77-40A-001 .
16 601306201 SHORT DOOR LOCK (2155) 1 GSK-501SB2155 (keyway, left)
17 0D4020600 BV SIDE PANEL 1 SECC-C 1.2t
18 0C0010000 PCB DOOR HINGE 1 D-HH100
19 2D4007800 SUPER KNOB 1 SK-34
20 0D4016000 BV CASE BKT 1 SECC-C 1.2t
21 0D4016200 BV SW COVER (JCM) 1 SECC-C 1.2t
22 ML2-651-00 ML2 BV SIDE BLIND PLATE 1 SECC-C 1.2t
23 0D4020800 STACKER DOOR LINK PLATE 1 SECC-C 2.3t
24 0D4021000 STACKER DOOR LOCK PLATE 2 SECC-C 2.3t
25 0D4021200 STACKER DOOR LOCK HOLDER 1 SECC-C 1.2t
26 0D4019400 SPACER 2 3382309-40030
9-12
No. 6 NOTE ACCEPTOR (GPT) ASSEMBLY
9-13
NOTE ACCEPTOR (GPT) ASSEMBLY (PARTS LIST)

1 0D4010800 BV SUPPORT BKT (GPT) 1 SECC-C 1.2t
2 ML2-659-00 BV ADJUST BKT W 1 SECC-C 2.0t
3 0D4010400A BV CASE (GPT) 1 SECC-C 1.2t
4 ARGUS SW BKT 1 SECC-C 1.6t
5 0C0016200 ARGUS SW BASE 1 SECC-C 1.6t
6 BILL VALIDATOR HEAD ARGUS-D 1
7 ENCLOSURE 1
8 STACKER 1
9 600132100 MICRO SW 2 AM50632C3
10 0C0017000 ARGUS SW BKT COLLAR 2 SS400 Φ10
11 0C0017200 ARGUS SW BKT SPACER 1 SS400 Φ10
12 0D4010600 BV REAR COVER (GPT) 1 SECC-C 1.2t
13 2D4007800 SUPER KNOB 1 SK-34
14 0D4016000 BV CASE BKT 1 SECC-C 1.2t
9-14
No. 7 CONTROL PANEL ASSEMBLY
9-15
CONTROL PANEL ASSEMBLY (PARTS LIST)

1 0D4113400 COIN ENTRY 1
2 COIN ENTRY B 1 Depends on denomi
3 PLATE G-ENEX 1 AI t=1.0
4 MEX-517-00 CONTROL PANEL MALL AUS 1 ABS
5 MEX-515-00 CTRL PNL FRM ASM AUS 1
6 MEX-519-00 CONTROL PNL ASM 15 AUS 1
7 ML2-001-00 ML2 DR BILL FACE 1 ABS
8 ML2-437-00 ML2 DR BILL FACE EARTH 1 SECC t=1.0
9 D-25-0004 ST BILL SIGN 1 PC t=0.5
10 BD-GM-M2BV 1 P509009-0101TI
11 PUSH BUTTON 3 SS-18UKK-x-LEDT5-W-F By the game.
12 GAME BUTTON FILM 3 PET t=0.2 By the game.
13 PUSH BUTTON 2 SS-25KK-W-LEDT5-W-F By the game.
15 PUSH BUTTON 2 SS-41KK-X-LEDT5-W-F By the game.
9-16
No. 8 DOOR ASSEMBLY (1/2)
9-17
DOOR ASSEMBLY (1/2) (PARTS LIST)

1 ML2-412-00 ML2 DR LK PIN BRKT B 2 SECC t=1.6

2 ML2-413-00 ML2 DR BLY LK PIN BRKT 2 SECC t=1.6
3 ML2-443-00 ML2 DR SENSOR BASE 1 SECC t=1.2
4 0D4106600 DOOR LOCK SHAFT 4 SUS303φ=6
5 0D4011200 SPACER 4 3382309-60100 (φ6,10mm)
6 MEX-220-00 ASSY DOOR MAIN FRAME 1

7 ML2-009-00 ML2 DR IF BEZEL-4 1 ABS
8 ML2-445-00 ML2 DR EXTRUSION R 1 A6063-T5
9 ML2-444-00 ML2 DR EXTRUSION L 1 A6063-T5
10 D-25-0005 ST ARUZE 1 PC t=0.5
11 D-25-0002 ST BV FACE (ENG) 1 PC t=0.5

12 ML2-010-00 ML2 PRINTER BEZEL 1 ABS
13 BD-GM-PRI-LED 1 P509007-0101YK
14 ML2-423-00 ML2 DR PRINT C ASM 1
15 D-25-0007 ST PR BEZEL (ENG) 1 PC t=250µm
16 ML2-163-00 MONITOR MASK19 ASM 1

17 ML2-489-00 MOMITOR MASK LED LENS 2
18 SENSOR 1 KB875-AZ01LF
19 CLAMP 3 EMT-3N
20 2D4106600 SPONGE FOR HOPPER 1 CR
21 2ZZZ55200 SPONGE FOR SEAL (WD) 1

22 ML2-483-00 PTS BLANK PANEL 1
23 MEX-266-00 REFLECTOR BRKT L ASM 1
24 MEX-262-00 DOOR REF FRONT CASE L 1
25 MEX-263-00 DOOR REF REAR CASE L 1
26 MEX-264-00 SPEAKER BOX L 1

27 SPEAKER 2 F02210D0
28 MEX-274-00 SPEAKER COVER PANEL 2
29 MEX-265-00 SPEAKER NET L 1
30 MEX-272-00 REFLECTOR BRKT R ASM 1
31 MEX-262-00 DOOR REF FRONT CASE R 1

32 MEX-269-00 DOOR REF REAR CASE R 1
33 MEX-270-00 SPEAKER BOX R 1
34 MEX-271-00 SPEAKER NET R 1
35 ML2-735-00 RUBBER 300x3x7 3 CR
36 ML2-736-00 RUBBER 375x2x7 1 CR

37 No.11 19IN MAIN LCD ASSEMBLY 1
9-18
No. 9 DOOR ASSEMBLY (2/2)
9-19

1 ML2-411-00 ML2 DR ROLL BRKT ASM 1

2 ML2-432-00 BLY DOOR HINGE UPR ASM 1
3 ML2-433-00 BLY DOOR HINGE LWR ASM 1
4 ML2-434-01 BLY DR SLIDE GUIDE A 1 SPCC t=2.0
5 ML2-434-02 BLY DR SLIDE GUIDE B 1 SPCC t=2.3
6 ML2-434-03 BLY DR SLIDE GUIDE C 1 SPCC t=2.3

7 600205001 PHOTO SENSOR 1 U-97PA
8 0D4107000 DOOR ROLLER SHAFT 1 SUS303 φ=7
9 0C0108200 BEARING 1 DR-26-H6
10 ML2-002-00 ML2 DR BLY COVER 2 1 ABS
11 ML2-004-00 ML2 DR BLY MALL 2 ABS

12 ML2-431-00 ML2 DR BLY KEY HK SLD 1 SECC t=2.3
13 ML2-401-00 ML2 DR BLY HK ASM 1
14 0D4014200 LOCK SLIDER COLLAR 8 C3601BD φ=10
15 ML2-420-00 ML2 DR BLY KEY PLT 1(2) SECC t=2
16 ML2-428-00 ML2 DR BLY COVER ASM 1

17 ML2-470-00 ML2 COIN TRAY CHUTE ASM 1
18 ML2-167-00 ML2 DR BLY LED PLATE 1 PC t=2
19 ML2-427-00 ML2 DR BLY LED COVER 1 SECC t=1.2
20 TENSION SPRING 1 E-593
21 601306201 KEY 1 GSK-501SB2155 (LH)

22 2L3105000 RUBBER 2 TM-96-3
23 ML2-400-00 ML2 DR BLY REF-2 1 SECC t=1.2
24 ML2-148-00 ML2 DR BLY ACRYLIC 1 PC t=3
25 ML2-149-00 ML2 DR BLY GLASS 1 t=3
26 ML2-467-00 COIN TRAY BASE ASM 1

27 ML2-468-00 COIN TRAY 1
28 2C0007400 DOOR GUIDE 1 POM
29 ML2-402-00 ML2 DR COUNTER BRKT ASM 1
30 IM-0078-00 INNER COUNTER BKT 1 SECC-C t=1.0
31 0D4109400 DUMMY COUNTER (3P) 1 SECC-C t=0.8

32 2D4109600 PLATE COUNTER 5 (SA,CE) 1 PC t=0.5
33 2D4107000 SPONGE FOR COUNTER FIX 1 C-4305
34 COUNTER 1 GC-127BA-5L800
35 ML2 DR PCB RID 1 SECC t=1.2
9-20

36 ML2 DR DOOR PCB CASE 1
37 CEK000900 DOOR_C PCB (PF) 1 UA2054-1C(PF)
38 600138000 DOOR SWITCH 2(3) SDKNA 20600
39 810338200 EDGING SADDOL 2 TSB-3027
40 602373200 FL SOCKET 1 UNV-09
41 602305200 FL TUBE 1 FL10N
42 FL DC INVERTER UNIT 1 AN-151F-1 ROHS
43 810338000 EDGING SADOL 1 TSB-1915
44 ML2-490-00 ML2 BLY GLASS SPONGE A 1 CR
45 ML2-491-00 ML2 BLY GLASS SPONGE B 1 CR
46 CEK000400 BD-GM-M2 LED4 3 P509008-0101TI
47 ML2-436-00 ML2 DOOR SW BRKT 1 SECC t=1.2
48 ST W HIGH VOLTAGE UL 1 PET t=0.75
49 ML2-494-00 ASSY ML2 DIVERTOR BRKT 1
50 0C0106800 DIVERTER BKT 1 SECC-C 1.6t
51 2C0106200 DIVERTER CHUTE 1 POM
52 SOLENOID 1 G836-AR51E DC12V
53 0A0120400 SOLENOID SPRING 1 SWP
54 COIN COMPARITOR 1 Model Name: CONDOR CP-130
Manufacturer: Money Controls
Firmware: CFG: CP130SAU00111, Build: BAAS01
55 COIN COMPARITOR 1 COINMECH MC-62 (Not used)
56 MEX-514-00 DOOR IO COVER AUS (1)
57 KEY CYLINDER (1) F750-MSDS
58 COUNTER (1) GC-127BA-8L700
9-21
No. 10 19INCH MAIN LCD ASSEMBLY
9-22
19INCH MAIN LCD ASSEMBLY (PARTS LIST)

1 ML2-706-00 19LCD REAR COVER ASM 1
2 ML2-718-00 19LCD ADJUSTER BRKT UNDER 2 1
3 810346200 CLAMP 1 EMT-6N
4 ML2-704-00 19LCD UNDER RUBBER 1 1
5 ML2-705-00 19LCD UNDER RUBBER 2 2
6 ML2-703-00 19IN TOUCH PANEL PCB COVER 1
7 810338800 EDGING SADDOL 2 ES-1010
8 ML2-707-00 19LCD BASE BRKT ASM 1
9 ML2-716-00 T PNL RUBBER 2
10 EDGING FOR TOUCH PANEL 2
11 19IN TOUCH PANEL 1 Model Name: PTD-7019-D-02
Manufacturer: PENTEL Co.,LTD.

12 ML2-717-00 19LCD ADJUSTER BRKT LR 2 2
13 ONE TOUCH BUSH 2 NB-8
14 19IN LCD 1 Model Name: LM190E03
Manufacturer: LG.PHILIPS LCD CO., LTD

15 ML2-408-00 19IN LCD CASE ASM 1
16 INVERTER PCB 1 IM6501
17 ML2-183-00 19IN INSURATION SHEET 1 PC t=0.5
18 SCALING PCB 1 Model Name: CSC001

19 ML2-419-00 19IN LCD REAR COVER ASM 1
20 ML2-418-00 19IN LCD ADJ COVER 1 SECC t=1.2
21 ST W HIGH VOLTAGE UL 1 PET t=0.75
22 2D4106400 LCD RUBBER 6 EPM
22 2D4106400 LCD RUBBER 2 EPM For 3 REEL
23 ML2-700-0 19LCD ADJUSTER BRKT UNDER 1 For 3 REEL
24 ML2-701-0 19LCD ADJUSTER BRKT LR 2 For 3 REEL
25 19IN LCD UNIT 3W 1 3W 061120 For 3 REEL
26 ML2-715-00 3 REEL WALL PLT UL 2 For 3 REEL
27 ML2-724-00 3-4 REEL SIDE WALL 2 For 3 REEL
28 ML2-725-00 3-4 REEL SIDE WALL LR 2 For 3 REEL
29 EDGING SADDLE 1 For 3 REEL
9-23
No. 11 3 REEL ASSEMBLY
9-24
3 REEL ASSEMBLY (PARTS LIST)

1 ML2-709-00 ASSY 3REEL BASE 1
2 ST C NOT TOUCH UL 3 PET t=0.75
3 REEL TAPE 3 PC t=0.2
4 500-0131 BD-GM-M2DRV/P509006-0303TI 1
5 ML2-708-00 REEL DRV CASE 1
6 810338000 EDGING SADDLE 2 TSB-1915
7 810291400 EDGE SUPPORT 4 ELBT-4N
8 20222670 REEL END WASHER 3
9 500-0140 BD-GM-BKLED3/P509013-0202YA 3
10 REEL-001-00 3 REEL MAIN BASE ASM 3
11 ML2-727-00 3 REEL BL BASE 3 ABS
12 ML2-710-00 REEL DRUM 2066IN 3 ABS
13 ML2-711-00 REEL DRUM 2066OUT 3 ABS
14 WIRE SADDLE 9 RLWT-1V0
15 STEP MOTOR 3
16 REEL-002-00 D SENSOR BASE 3
17 600290700 PHOTO SENSOR 6 KI1306-AA
9-25
No. 12 GM HOPPER ASSEMBLY (1/2)
9-26
GM HOPPER ASSEMBLY (1/2) (PARTS LIST)

1 0C0306800 SENSOR BKT 1 SECC-C 1.0t
2 IM-0017-00-2 HOPPER MOUNT BASE 1 SECC-C 2.0t
3 IM-0103-00 HOPPER BUCKET PARTITION 1 SUS 430-CP 1.0t
4 IM-0105-00 HOPPER COVER 1 SECC-C 1.0t
5 0P0308200 HOPPER BUCKET SPRING 4 SWP-B φ1.4
6 CONTROL BOX 1 ABS
7 HOPPER BUCKET FLANGE 1 POM
8 HOPPER BUCKET 1 ABS
9 GM HOPPER INNER HARNESS 1
10 3C0305200 GM HOPPER COUNT HARNESS 1
11 CEK002600 HOPPER PCB 1 Model Name BD-GM-HOPPER/ 98203-MH (ROHS)
12 0P0310800 SPACER 4 4ER25
13 0P0311000 SPACER 1 4SP25
14 1 KI659-AALF
15 2P8003000 ANP BASE 3 ANP 1D
16 810105200 INSULOCK TIE (CABLE BAND) 4 PLT1M
17 IM-0104-00-1 HOPPER REAR COVER 1 SECC-C 1.2t
18 0C0013200 BUILT-IN KNOB 1 AT-100B (Thickness of mounting panel: 1.2mm)
19 SHIELD TIGHT 1 STG4-9L100
9-27
No. 13 GM HOPPER ASSEMBLY (2/2)
9-28
GM HOPPER ASSEMBLY (2/2) (PARTS LIST)

1 HOPPER BACK PLATE 1 SPCC-SD 3.2t
2 0C0306600A COUNT ROLLER ARM 1 SUS 430-CP 1.5t
3 COIN GUIDE PLATE 1 SUS 304-CSP 0.6t
4 0C0307200 KNIFE SPACER 1 SPCC-SD 3.2t
5 COIN SHIELD 1 By token size.
6 0P0302600 COIN WIPER $ 1 SPCC-SD 2.0t
7 0P0302400 WIPER HOLDER 1 SPCC-SD 1.0t
8 KNIFE 1 By token size.
9 PIN WHEEL 1 SPCC-SD 3.2t By token size.
10 SHELF WHEEL 1 SUS 430-CP 1.5t By token size.
11 0P0306000 COIN WIPER SPRING 2 SWP-Bφ0.65
12 0P0309800 COUNT ARM PIN 1 SS400φ7
13 0C0309600 COUNT ROLLER 1 SK4φ16
14 0C0309800 COUNT ROLLER AXIS 1 SS400φ10
15 0P0306200 WIPER SPRING SPACER 2 SS400
16 0P0308800 ROLLER PIN 4 SK4φ7
17 MOUNTING PLATE 1 ADC-12
18 2C0305000A PIN WHEEL DRIVE HUB 1 POM
19 2P0302200 AGITATOR 1 CR RUBBER
20 DC MOTOR 1 163DV-2BUVV-L
21 0P0308600 RADIAL BALL BEARING 4 626ZZ M3SML Y121
22 0C0309200 SPRING 1 E598
23 0P0306400 PLASTIC WING BOLT 1 M3×6
24 0P0310600 SPACER 3 1382309-50055
25 2C0305600 WASHER 1 CC-0613-10
26 SPRING 1
9-29
BLOCK DIAGRAM G-ENEX(NSW)
POWER BOX PCB BOX
AC220V- 240V COOLING USB OPT IN OPT OUT DIVERTER
INLET FUSE OUTLET DC+ 12V
FAN PCI2 DC+ 5V RS23 2C AGP1 DC+ 12V OUTP ORT SENS OR SENS OR COIL
EDGE EDGE
CONNECTOR CONNECTOR COIN
DOOR P CB
DC+3 .3V POWER IN ACCEP TOR
AC220V- 240V POW ER RS POW ER INPORT CASE SW
FUSE INPORT 232C
IN IN DOOR I/O DROP CO IN
DC+ 5V POWER IN IDE IDE BD-GMEM USB
IDE
MAIN PCB PCB SENS OR
CABLE
_2nd-02
NOISE DC+ 12V POWER IN BD-S TH VIDEO P CB BD-G M-FDAMP OUTP ORT CONTROL PANEL
MEMORY DC+ 12V
MAIN EDGE UNIT
FILTER PCB CONNECTOR
POWER IN
SWI TCH BUTTON
BOARD DC-12V POWER IN INPORT
VGA DVI DC+ 24V SWITCH ES
BD-GEM_Cass ette OUT POWER IN
USB USB PCB OUT OUT INPORT PORT DC+ 24V BUTTON
Block Diagram
COMPACT DOOR RS23 2C OUT LEDS

OUTLET SWITCHING POWER
SUPPLY BO ARD FLASH SW
DC+ 5V
DC+ 5V POLYSWITCH
RS23 2C
AC220V- 240V IN DC+ 12V TOUCH P ANEL TOUCH P ANEL
DC+ 12V POLYSWITCH
SWITC HING CONTR OLER SENS OR
POWER SUPP LY DC+ 24V COMMUNICA TION COMMUNICA TION
DC+ 24V POLYSWITCH
DC+ 24V DC+ 24V
LVDS
DVI IN LVDS IN
OUT
POWER IN POWER IN DC+ 5V SCAL ING 1ST LCD
POWER IN PCB
LED CONTR OL BD- TOP FL INVERT ER USB POWER IN INVERTER P CB
SERIAL PORT CONTROL FL OUT FL
DC+ 12V
POWER IN
AUSCOM- A PCB
G-TOPPER BD-GM -M2BV
BD-GM TP RLED1 BD-GM-M 2LED1 UNIT (OPTION) POWER IN
LED CONTROL SERIAL PORT LED CONTROL SERIAL PORT FL INVERT ER
BELLY FL OUT
BD-GM-M 2LED1 BD-GM TP RLED1 DOOR SW
USB
LED CONTROL SERIAL PORT LED CONTROL SERIAL PORT
POWER IN OUTP ORT BD-GM-M 2LED4 METE RS FL

BD-T T-LED BD-T T-LED TOWER
LED CONTROL SERIAL PORT LED CONTROL SERIAL PORT LIGHT
POWER IN BD-GM-M2IO INPORT
OUTP ORT BELLY DOOR
9-1
BODY PCB MAIN
KEY SW
2ND L CD SCAL ING CASE SW DOOR SW
VGA IN
PCB DC+ 5V MAIN
LVDS IN LVDS OUT POWER IN SPEAKER( L)
INVERTER P CB DC+ 12V
POWER IN MAIN
CABINET UNIT SPEAKER(R)
LED CONTR OL
SERIAL PORT BD-GM-M 2LED4
INPORT
BD-GM- MAIN DOOR
DC+12V or DC+ 24V RS23 2C RS23 2C TICKET
PRI_L ED WOOFER BD-GM-M 2LED4
RS23 2C DC+ 24V POWER IN PRINTER
SPEAK ER
BD-GM- BD-GM- BD-RK 2- BD-RK 2-

M2LE D4 M2LE D4 HARO HARO
CABINET HEAD UNIT
DC HOPPER UNIT
SENS OR
MOTOR POWER IN RS232C
LEVEL SW BILL VAL IDATOR
STACKER DO OR SW
OUTP ORT INPORT & BILL DOO R SW
INPORT
HOPPER P CB OUTP ORT
BILLVALI CABINET
Block Diagram
UPDATE:2007-03-16
Wiring Diagram
Wiring Diagram
9-1
Wiring Diagram
9-2
Wiring Diagram
9-3
Wiring Diagram
9-4
Wiring Diagram
9-5
G-ENEX
Video Slot Gaming Machine
Service Manual
Aruze Gaming America, Inc.

745 Grier Drive Las Vegas, NV 89119, USA
Aruze Gaming America, Inc. Japan Branch

Ariake Frontier Bldg. A, 3-1-25, Ariake, Kohto-ku, Tokyo, 135-0063
Aruze Gaming Australia Pty. Ltd

23-27 Bourke Road,
Alexandria, NSW 2015, Australia
Aruze Gaming Africa (Pty.) Ltd.

Unit 1-3, Kyalami Village, 57 Forssman Close, Barbeque Down Ext 1, Unit 1,
Kyalami, Midrand, Gauteng, South Africa
©2007 ARUZE CORP. All Rights Reserved.

CONTENTS OF THIS PUBLICATION MAY NOT BE REPRODUCED IN ANY
WAY FORM WITHOUT WRITTEN PERMISSION OF ARUZE.
THIS MANUAL MAY BE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.

G-Enex Video Service Manual Aruze 103

Uploaded by

Copyright:

Available Formats

G-Enex Video Service Manual Aruze 103

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

G-Enex Video Service Manual Aruze 103

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL

G-ENEX Video Slot Gaming Machine

This manual is intended for Operators, Owners, and Qualified Maintenance/Service

TO THE MAXIMUM EXTENT PERMITTED BY LAW, ARUZE SHALL NOT BE

DANGER It warns of the immediate hazards which WILL

WARNING It warns of hazards or unsafe practices which

CAUTION It warns of hazards or unsafe practices which

If a problem happens, please contact your nearest distributor.

To prevent an accident or a fire;

1. Install this machine on flat, stable, well-constructed floor.

Risk of Electric Shock.

6. Disposal of Lithium Batteries

Risk of Injury of Fire

NEVER retrofit the machine. Retrofitting the machine could cause an

Technical Support ............................................................................................. i

Limited Warranty ............................................................................................ ii

Safety Instructions .......................................................................................... iii

Table of Contents .......................................................................................... viii

Chapter 1: Major Components............................................................... 1-1

Chapter 2: Installation............................................................................. 2-1

Chapter 3: Software Setting .................................................................... 3-1

3.2.4 TICKET PRINT TEST.................................................................................. 3-10

Chapter 4: Hardware Setting.................................................................. 4-1

Chapter 5: Test Mode............................................................................... 5-1

Chapter 6: Preventative Maintenance ................................................... 6-1

6.5.3 Main Door ..................................................................................................... 6-18

Chapter 7: Troubleshooting .................................................................... 7-1

Chapter 8: Machine Specifications......................................................... 8-1

Chapter 9: Parts Catalog......................................................................... 9-1

Block Diagram .............................................................................................. 9-1

Wiring Diagram ............................................................................................ 9-1

Chapter 1: Major Components

1. Tower Light (Option) 2. Sub-LCD

1.2 Internal Structure

1. Body I/O PCB Housing 2. Main LCD 3. Coin Acceptor

4. Coin Diverter 5. Door I/O PCB Housing 6. Inverter Fluorescent Lamp

7. Security Cage 8. Hopper 9. Note Acceptor

10. Ticket Printer (Optional) 11. Woofers 12. Power Box

13. Power Switch 14. AUSCOM PCB

5 1. Fluorescent Lamp Unit

3. Coin Drop Sensor

4. Belly Door Switch

5. Note Stacker Lock

1. Inverter and Scaling PCB

2. Touch Panel PCB Housing

4. Connected to Door I/O PCB

5. Connected to Body I/O PCB

Located in Top Box

8. Security Cage Door

8 9. Security Cage Lock

1.3 Closing Door

2.1 Unpacking and Inspection

The installation must be performed by qualified service personnel.

Tower Light (Option) 1

2.2 Cabinet Dimension

155 (2 tiers tower light)

Keep at least the following space between the machines.

2.3 Installing the Machine on Your Cabinet Stand

1. Place the template (option) on your cabinet Template

6-φ9 HOLE ;(a)