Scribd
Upload
66 views2 pages

Department of Electrical & Electronics Engineering: Class Section Code-Subject Name of The Faculty

This document provides an assignment for a B.Tech third semester Electrical Measurements and Instrumentation class. It includes 15 questions covering topics from Units III and IV such as ratio correction factor, current transformers, potentiometers, volt ratio boxes, cathode ray oscilloscopes, linear variable differential transformers, digital storage oscilloscopes, electrostatic deflection, and Lissajous patterns. The assignment is to be submitted by December 11th, 2020 for a maximum of 10 marks.

Uploaded by

v srinivas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
66 views2 pages

Department of Electrical & Electronics Engineering: Class Section Code-Subject Name of The Faculty

This document provides an assignment for a B.Tech third semester Electrical Measurements and Instrumentation class. It includes 15 questions covering topics from Units III and IV such as ratio correction factor, current transformers, potentiometers, volt ratio boxes, cathode ray oscilloscopes, linear variable differential transformers, digital storage oscilloscopes, electrostatic deflection, and Lissajous patterns. The assignment is to be submitted by December 11th, 2020 for a maximum of 10 marks.

Uploaded by

v srinivas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DEPARTMENT OF ELECTRICAL & ELECTRONICS ENGINEERING

KAKATIYA INSTITUTE OF TECHNOLOGY & SCIENCE, WARANGAL


(An Autonomous Institute under Kakatiya University, Warangal)

Assignment-II
(UNIT – III & IV)
Class B.Tech. III-Semester
Section EEE-1 & EEE-2
Code-Subject U18EE304 –Electrical Measurements and Instrumentation
Name of the faculty Sri. K. Ajith, Assistant Professor, EEED &
Sri. M. Srinivas, Assistant Professor, EEED
Assignment posted on 02-11-2020
Date for Assignment Submission 11.12.2020
Max. Marks: 10
Questions 1 – 10 for submission:
Q. Marks CO CDLL
No.
1 Define the terms (i) Ratio Correction Factor (ii) Burden. [1] CO3 R
2 "Never open the secondary winding circuit of a current transformer while its [1] CO3 U
primary winding is energized" - Explain.
3 A basic slide wire potentiometer has a working battery voltage of 3V. The [1] CO3 Ap
resistance of slide wire is 400Ω and its length is 200cm. The slide wire has 1mm
scale divisions and it is possible to read up to 1/5 of a division. The instrument is
standardized with 1.018V standard cell with sliding contact at 101.8 cm. Calculate
(i) working current
(ii) the resistance of series rheostat
(iii) the measurement range
(iv) the resolution of instrument
4 Design a volt ratio box with a resistance of 20ohm/volts and ranges 3V, 10V, 30V, [1] CO3 Ap
100V. The volt ratio box is to be used with a potentiometer having a measuring
range of 1.6V.
5 A volt ratio box is shown in the figure. The input voltage is 100V and output [1] CO3 An
voltage is 2V.The total input resistance (R1+R2) is 10MΩ. Determine the ratio of
the volt ratio box, R1 and R2 values.

R1

Vinput
Voutput POTENTIOMETER
R2

6 Write a short notes on screens used for Cathode Ray Oscilloscope. [1] CO4 R
7 With neat sketch explain the working principle of Linear Variable Differential [1] CO4 R
Transformer (LVDT) used for measuring displacement.
8 Differentiate Digital Storage Oscilloscope (DSO) and Cathode Ray Oscilloscope [1] CO4 U
(CRO)
9 Explain why Electrostatic deflection scheme is used in CRO? [1] CO4 U
10 A signal with known frequency and another signal with unknown frequency are [1] CO4 Ap
applied to the X and Y channels of CRO respectively. The internal sweep
generator is disconnected. Draw the Lissajous patterns for the following ratios of
known frequency to unknown frequency: 1:1, 1:2, 2:1, 2:2, 3:1 and 3:2
Questions 11 – 15 for practice (not for submission):

Q.
CO CDLL
No.
11 Draw the circuit diagram of Phase shifting transformer and label the parts. CO3 R
12 Two sinusoidal signals with same magnitude and frequency are applied to the X and CO4 U
Y channels of CRO. The internal sweep generator is disconnected. Draw the Lissajous
patterns when the phase displacement between the two signals is 0, 30, 90, 120, 150
and 240.
13 With neat sketch explain the working principle of resistance strain gauge. Derive the CO4 R
equation for gauge factor of the resistance strain gauge.

14 Derive the expression to find out ratio error and phase angle error of a current CO3 U
transformer by using Silsbee's test.
15 With neat sketch(s) explain the operation of phase shifting transformer and phase CO3 U
shifting circuit. Discuss why phase shifting transformer and phase shifting circuit are
necessary to calibrate polar and co-ordinate type potentiometer.

*****

You might also like