WWW - Manaresults.Co - In: Set - 1 Code No: RT32033
WWW - Manaresults.Co - In: Set - 1 Code No: RT32033
WWW - Manaresults.Co - In: Set - 1 Code No: RT32033
3 a) Design a center crank shaft for a single acting four stroke engine for the following [16M]
data:Bore = 200mm, stroke = 300mm, engine speed = 1000 rpm, length of connecting
rod = 600mm, Maximum combustion pressure = 1 N/mm2, the crank shaft carrying
one fly wheel at one end of each journal. Weight of each flywheel = 2 kN, distance
between flywheel and its nearest journal = 150 mm.
Maximum torque is experienced in the crank shaft when the crank angle is 300 from
inner dead center position. Permissible stresses for crank shaft material are 70 N/mm2
in bending, 40 N/mm2 in shear, limiting bearing pressure is 8 N/mm2. The length to
diameter ratio 1.2 for both crank pin and journal. Assume required data.
1 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: RT32033 R13 SET - 1
4 Design a cast iron piston for a single acting four stroke diesel engine with the [16 M]
following data
Cylinder bore = 300mm
Length of stroke = 250mm
Speed = 600 rpm
Brake mean effective pressure = 0.6 MPa
Maximum gas pressure = 4MPa
Fuel consumption = 0.25 kg per BP per h
l/d ratio for bush in small end of connecting rod = 1.5
Assume suitable data if required and state the assumptions made.
7 a) A pair of parallel helical gears consists of a 20 teeth pinion meshing with a 100 teeth [8M]
gear. The pinion rotates at 720 rpm. The normal pressure angle is 200, while the helix
angle is 250, the face width is 40 mm and the normal module is 4 mm. the pinion as
well as gear is made of steel 40C8 (Sut = 600 N/mm2) and heat treated to a surface
hardness of 300 BHN. The service factor and the factor of safety are 1.5 and 2
respectively. Assume that the velocity factor accounts for the dynamic load and
calculate the power transmitting capacity of gears.
b) A cranked lever has the following dimensions: Length of the handle = 300 mm, [8M]
Length of the lever arm = 400mm, overhang of the journal = 100 mm. if the lever is
operated by a single person exerting a maximum force of 400 N at a distance of 1/3 rd
length of the handle from its free end, find i) diameter of the handle ii) cross section of
the lever arm iii) diameter of the journal.
The permissible bending stress for the lever material may be taken as 50 MPa and
shear stress for shaft material as 40 Mpa.
WWW.MANARESULTS.CO.IN *****
|''|'''||''||'''|||| 2 of 2
Code No: RT32033 R13 SET - 2
6 a) It is required to select a flat open belt drive for a compressor running at 720 rpm, [8M]
which is driven by a 25 kW, 1440 rpm motor space is available for a center distance
of 3m.
b) A power screw having double start square threads of 25 mm nominal diameter and 5 [8M]
mm pitch is acted upon by an axial load of 10 kN. The outer and inner diameters of
screw collar are 50mm and 20 mm respectively. The coefficient of thread friction and
collar friction may be assumed as 0.2 and 0.15 respectively. The screw rotates at 12
rpm. Assuming uniform wear condition at the collar and allowable thread bearing
pressure of 5.8 N/mm2. Find
i) The torque required to rotate the screw
ii) The stresses in the screw and
7 a) A pair of straight teeth spur gears is to transmit 20 kW when the pinion rotates at 300 [8M]
rpm. The velocity ratio is 1:3. The allowable static stresses for the pinion and gear
materials are 120 MPa and 100 MPa respectively. The pinion has 15 teeth and its
face width is 14 times the module. Determine i) Module ii) face width iii) pitch
circle diameters of both the pinion and gear from the stand point of strength only,
taking into consideration the effect of the dynamic loading. The tooth form factor can
0.912 3
be taken as y = 0.154 and the velocity factor C v = where v is
no. of teeth 3+v
expressed in m/sec
b) State the applications of hand and foot levers. Discuss the procedure for designing a [8M]
hand or foot lever.
*****
WWW.MANARESULTS.CO.IN
2 of 2
|''|'''||''||'''||||
Code No: RT32033 R13 SET - 3
PART –A
1 a) What are the commonly used materials for sliding contact bearings? [3M]
b) Explain the various types of crank shafts. [3M]
c) Explain the function of piston rings. [4M]
d) Draw the distribution of stresses in curved beams across the cross section. [4M]
e) Differentiate between differential screw and compound screw. [4M]
f) Define i) Module, ii) Face width. [4M]
PART -B
2 a) Distinguish between “Hydrodynamic bearings” and “Hydrostatic bearings”. [4M]
b) A single row deep groove ball bearing is subjected to a radial load of 8 kN and a [12M]
axial load of 3 kN. The shaft rotates at 1200 rpm. The expected life of the bearing is
20000 hours. The minimum acceptable diameter of the shaft is 75mm. select a
suitable ball bearing for this application.
3 The following data is given for the connecting rod of a diesel engine: Cylinder bore = [16M]
85 mm, Length of connecting rod = 350 mm, Maximum gas pressure = 3 MPa, factor
of safety against the buckling failure = 5, l/d ratio for piston pin bearing = 1.5, l/d
ratio for crank pin bearing = 1.25, Allowable bearing pressure for piston pin bearing
= 13 MPa, Allowable bearing pressure for crankpin bearing = 11 MPa, stroke length
= 140mm, mass of reciprocating parts = 1.5kg, engine speed = 2000 rpm, allowable
stress in the bolts as 90 N/mm2 and in cap as 95 N/mm2, density of connecting rod =
7800 kg/m3 calculate:
a) Dimensions of the cross section of connecting rod
b) Dimensions of small and big end bearings
c) Nominal diameter of bolts for the cap
d) Thickness of cap and
e) Magnitude of whipping stress.
1 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: RT32033 R13 SET - 3
4 A cylinder of a four stroke diesel engine has the following specifications: [16M]
Brake power = 5 kW
Speed = 600 rpm
Indicated mean effective pressure = 0.5 MPa
Make suitable assumptions and calculate
a) Bore and length of the cylinder liner
b) Thickness of the cylinder liner
c) Thickness of the cylinder head
d) Size, number and pitch of studs.
5 a) Derive an expression for radius of neutral axis of a ‘I’ cross- section curved beam. [6M]
b) A central horizontal section of a hook is symmetrical trapezium 60 mm deep, the [10M]
inner width being 60 mm and the outer width being 30 mm. Estimate the extreme
intensities of stresses when the hook carries a load of 20 kN. the load line passes at
40 mm from the inside edge of the section and the center of curvature lies in the load
line.
6 a) It is required to select a V belt drive to connect a 15 kW, 2880 rpm normal torque A [8M]
C Motor to a centrifugal pump, running at approximately 2400 rpm, for a service of
18 hours per day. The center distance should be approximately 400mm. assume that
the pitch diameter of the driving pulley is 125mm
b) A vertical two start square threaded screw of a 100 mm diameter and 20mm pitch [8M]
supports a vertical load of 18kN. The axial thrust on the screw is taken by a collar
bearing of 250mm outside diameter and 100 mm inside diameter. Find the force
required at the end of a lever of 400 mm long in order to lift and lower the load. The
coefficient of friction for the vertical screw and net is 0.15 and that for collar bearing
is 0.20.
7 a) A pair of helical gears is to transmit 15 kW. The teeth are 200 stub in diametral plane [10M]
and have a helix angle of 450. The pinion runs at 10000 rpm and has 80mm pitch
diameter. The gear has 320 mm pitch diameter. if the gears are made of cast steel
having allowable static strength of 100 MPa, determine a suitable module and face
width from static strength considerations and check the gears for wear, given σes =
618 MPa
b) A foot lever is 1m from the center of the shaft to the point of application of 800N [6M]
load. Find i) diameter of the shaft ii) dimensions of the rectangular arm of the foot
lever at 60 mm from the center of the shaft assuming width of the arm as three times
the thickness. The allowable tensile stress may be taken as 73 MPa and allowable
shear stress as 70 MPa.
*****
2 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: RT32033 R13 SET - 4
3 Design a connecting rod for an IC engine running at 1800 rpm and developing a [16M]
maximum pressure of 3.15 N/mm2. The diameter of the piston is 100mm, mass of the
reciprocating parts per cylinder 2.25kg, length of connecting rod 380 mm, stroke of
piston 190 mm and compression ratio 6:1.take factor of safety of 6 for the design. Take
length to diameter ratio for big end bearing as 1.3 and small end bearing as 2 and the
corresponding bearing pressure as 10 N/mm2 and 15 N/mm2. The density of rod material
may be taken as 8000 kg/m3 and the allowable stress in the bolts as 60 N/mm2 and in cap
as 80 N/mm2. Assume I cross section for the connecting rod. The elastic limit of
compressive stress is 350 MPa and rankine constant 1/7500. Draw a neat dimensioned
sketch.
1 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||
Code No: RT32033 R13 SET - 4
5 a) Define curved beam? What is the difference with respect to straight beam [4M]
b) A crane hook has a trapezoidal section at A-A as shown in fig. find the maximum stress [12M]
at points P and Q
6 a) Design a chain drive to actuate a compressor from a 15 kW electric motor running at [8M]
1000 rpm. The compressor speed being 350 rpm. The minimum center distance is 500
mm. the compressor operates 16 hours per day. The chain tension may be adjusted by
shifting the motor on sliders
b) A nominal diameter of a triple threaded square screw is 50mm, while the pitch is 8 mm. [8M]
it is used with a collar having an outer diameter of 100mm and inner diameter as 65mm.
the coefficient of friction at the thread surface as well as at the collar surface can be taken
as 0.15.the screw is used to raise a load of 15 kN. using the uniform wear theory for
collar friction, calculate
i)Torque required to raise the load ii)Torque required to lower the load and
iii)The force required to raise the load, if applied at a radius of 500 mm
7 a) Design a pair of spur gears with 200 full-depth involute teeth consisting of a 20 teeth [10M]
pinion meshing with a 50 teeth gear. The pinion shaft is connected to a 22.5 kW, 1450
rpm electric motor. The starting torque of the motor can be taken as 150% of the rated
torque. The material for the pinion is plain carbon steel Fe410 (Sut = 410 N/mm2), while
the gear is made of grey cast iron FG200 (Sut = 200 N/mm2). The factor of safety is 1.5.
design the gears based on the Lewis equation and using velocity factor to account for the
dynamic load
b) A right angled bell crank lever is to be designed to raise a load of 5 kN at the short arm [6M]
end. The lengths of short and long arms are 100 and 450 mm respectively. The lever and
the pins are made of steel 30C8 (Sut = 400 N/mm2). And the factor of safety is 5.the
permissible bearing pressure on the pin is 10 N/mm2. The lever has a rectangular cross
section and the ratio of width to thickness is 3:1. The length to diameter ratio of the
fulcrum pin is 1.25:1. Calculate i) the diameter and length of the fulcrum pin ii) the
dimensions of the cross section of the lever
*****
2 of 2
WWW.MANARESULTS.CO.IN
|''|'''||''||'''||||