Scribd Logo
Upload

Welcome to Scribd!

  • 492 views

    Pistons and Connecting Rods - Install: Desmontagem e Montagem

    Uploaded by

    Jefferson Silva
    This document provides instructions for installing pistons and connecting rods in a 3304 engine. It lists the required tool and gives steps to position the crankshaft, coat parts with oil, install each piston with the "V" marks aligned, guide the connecting rod onto the crankshaft, apply oil and torque the connecting rod cap nuts. It concludes by noting additional steps to install the oil pump, oil pan plate and spacer plate.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Pistons and Connecting Rods - Install: Desmontagem e Montagem

    Uploaded by

    Jefferson Silva
    492 views3 pages
    This document provides instructions for installing pistons and connecting rods in a 3304 engine. It lists the required tool and gives steps to position the crankshaft, coat parts with oil, install each piston with the "V" marks aligned, guide the connecting rod onto the crankshaft, apply oil and torque the connecting rod cap nuts. It concludes by noting additional steps to install the oil pump, oil pan plate and spacer plate.

    Original Title

    3304 MONTAGEM PISTAO E BIELApdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for installing pistons and connecting rods in a 3304 engine. It lists the required tool and gives steps to position the crankshaft, coat parts with oil, install each piston with the "V" marks aligned, guide the connecting rod onto the crankshaft, apply oil and torque the connecting rod cap nuts. It concludes by noting additional steps to install the oil pump, oil pan plate and spacer plate.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    492 views3 pages

    Pistons and Connecting Rods - Install: Desmontagem e Montagem

    Uploaded by

    Jefferson Silva
    This document provides instructions for installing pistons and connecting rods in a 3304 engine. It lists the required tool and gives steps to position the crankshaft, coat parts with oil, install each piston with the "V" marks aligned, guide the connecting rod onto the crankshaft, apply oil and torque the connecting rod cap nuts. It concludes by noting additional steps to install the oil pump, oil pan plate and spacer plate.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3
    At a glance
    Powered by AI
    The document provides instructions for installing piston and connecting rods in an engine.

    The steps include rotating the crankshaft, applying oil, positioning the piston rings, inserting the piston into the cylinder liner, and guiding the connecting rod onto the crankshaft.

    The identification marks on the connecting rod caps and connecting rods should be aligned.

    120G MOTOR GRADER 11W01019-01250 (MACHINE) POWERED BY 3304 E...

    Página 1 de 3

    Fechar o SIS

    Tela anterior

    produtos: MOTOR GRADER


    Modelo: 120G MOTOR GRADER 11W
    Configuração: 120G MOTOR GRADER 11W01019-01250 (MACHINE) POWERED BY 3304 ENGINE

    Desmontagem e Montagem
    3304B and 3306B Engines for Caterpillar Built Machines
    Número de Mídia -SENR5598-09 Data de Publicação -01/01/2013 Data de Atualização -25/01/2013

    i00976704

    Pistons and Connecting Rods - Install


    SMCS - 1225-012

    Installation Procedure
    Table 1
    Required Tools
    Tool Part Number Part Description Qty
    A 5P-3525 Piston Ring Compressor 1

    NOTICE

    Keep all parts clean from contaminants.

    Contaminants may cause rapid wear and shortened component life.

    1. Rotate the crankshaft until the bearing journals are at the bottom center. The bearing
    journals that are at the bottom center are for the piston installation.

    2. Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put
    clean engine oil on the piston rings and the connecting rod bearings.

    3. Move the piston rings on the pistons until the ring openings are separated by approximately
    120 degrees.

    https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 10/11/2020
    120G MOTOR GRADER 11W01019-01250 (MACHINE) POWERED BY 3304 E... Página 2 de 3

    Illustration 1 g00483337

    4. Put the piston in the cylinder liner with the "V" mark on the piston in alignment with the
    "V" mark on the cylinder block. Put tool (A) in position on the cylinder block and compress
    the piston rings.

    NOTICE

    The "V" mark must be visible on the piston and the cylinder block. If
    the "V" mark is not visible, the piston must be installed with the relief
    for the valve positioned toward the pushrod opening in the cylinder
    block. Damage may result if the pistons are not installed properly.

    5. Push the piston into the cylinder liner and out of the ring compressor.

    Illustration 2 g00483701

    6. Guide connecting rod (1) into position on the crankshaft.

    7. Put clean engine oil (SAE 30) on the lower half of the connecting rod bearing and on the
    connecting rod bolts.

    https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 10/11/2020
    120G MOTOR GRADER 11W01019-01250 (MACHINE) POWERED BY 3304 E... Página 3 de 3

    NOTICE

    When the connecting rod caps are installed, ensure that the
    identification marks are aligned.

    8. Install connecting rod cap (2) and the nuts that secure the connecting rod cap. Torque both
    of the nuts to 40 ± 4 N·m (30 ± 3 lb ft). Mark the position of the nuts. Tighten each nut for
    an additional 90 degrees (1/4 turn).

    9. Repeat Steps 1 through 8 for the remainder of the piston and connecting rods.

    End By:

    a. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
    Install".
    b. Install the engine oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate -
    Remove and Install".
    c. Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
    install".

    Direitos Autorais 1993 - 2020 Caterpillar Inc. Tue Nov 10 17:21:14 UTC-0200 2020
    Todos os Direitos Reservados.
    Rede Particular Para Licenciados SIS.

    https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 10/11/2020

    You might also like