Scribd
Upload
122 views2 pages

Heatmasters: Mobile Heat Treatment Equipment

HM31 is a small, lightweight preheating and annealing unit powered by an inverter that enables precise temperature control from 20-1200°C. It is programmed using the HeatMaster control system to easily perform standardized heat treatments on tubes up to 140mm in diameter using induction heating or heating resistors. HM31 records heat treatment results for documentation and can be connected to remote monitoring. Multiple HM31 units can be synchronized to treat larger objects.

Uploaded by

Anand Sankar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
122 views2 pages

Heatmasters: Mobile Heat Treatment Equipment

HM31 is a small, lightweight preheating and annealing unit powered by an inverter that enables precise temperature control from 20-1200°C. It is programmed using the HeatMaster control system to easily perform standardized heat treatments on tubes up to 140mm in diameter using induction heating or heating resistors. HM31 records heat treatment results for documentation and can be connected to remote monitoring. Multiple HM31 units can be synchronized to treat larger objects.

Uploaded by

Anand Sankar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

HeatMasters

MOBILE HEAT TREATMENT EQUIPMENT

HM31
HM31 is an inverter based preheating and annealing unit
especially for tubes. Setting, control and monitoring of HM 31
is carried out by the HeatMaster Control System. HM31 is
small and light in weight, which enables easy handling and Tecnical data
transportation. For power supply HM31 is connected to
Connection voltage 220 ... 240 V; one phase
mains current socket, which enables the use of short cables.
Heating power 3,5 kW, ED 100 %
Programming
Fuse 16 A, slow
By using HeatMaster System you can program heat treatment
Secondary voltage 0 ...70 V
instructions in the memories of dozens of HM31 units. When
Heating channels 1 pcs
the programming is complete, HM31 will carry out the heat
Measuring points 2 pcs
treatment according to the instructions it has received. The
Temperature range 20 ... 1200 °C
signal light of HM31 shows if any disturbances occur during
Control system HeatMaster Control
the operation. On the front panel is a digital display which
System
indicates the progress of the heat treatment.
Alarm Signal lights, option for
HM31 can be connected to long-distance monitoring.
long distance monitoring
Data registration
Dimensions Length 375 mm
The unit registers in its memory the achieved heat treatment
Width 150 mm
results, which enable easy preparation of heat treatment
Height 320 mm
documents. No separate temperature recorders for the
Weight 11 kg
induvidual devices are needed
INDUCTION HEAT TREATMENT WITH HEAT TREATMENT RESISTORS

HM31’s power source is an inverter, enabling the use of even


the smallest special resistors and heating of a very small objects.
Technical data of the resistrors are given on their own brochures.
HeatMaster resistors suitable for the HM31 unit:

Resistor type Quantity/HM31


VHV annealing heater 1
VHVP, annealing heater 2
VHK-spreader heater 1
HM31 VHY-stud heater 1
VET-preheating element 1
Operations to heat treat a tube maximum Ø140 mmm: VETS-preheating element 1
* Weld the thermocouple wire (max. 2 pcs) on the VETI-preheating element 1
welding seam by using the thermocouple attachment VETIS-preheating element 1
unit HM250. VEK-preheating element 1
* Cover the tube with thermal insulation and wind the VEKS-preheating element 1
induction coil around the oject to be heated. VLV-channel heater 1
* Connect cables to HM31 and start the heating.

The induction only heats the tube material, radiating heat loss
remains very small. Maximum temperature with induction method HAET TREATMENT DOCUMENTS
is around 700 °C. If a higher temperature is required a heating
resistor is to be used. HeatMaster system enables easy printing of heat treatment
certificates, based on the data of the heat treatment results.

INDUCTION ANNEALING WITH TWO HM31


UNITS
Large tube diameters and thick materials require annealing with

two HM31 units. Two units is needed when tube diameter


exceeds 140 mm
When using two HM31 units for annealing tthe object to be
heated must have at least one measuring point for each unit.
* Cover the tube with thermal insulation material and
wind the induction coil on both sides of the object.
* Connect the cables and start the heating.

The HeatMaster Heat Treatment Control System enables


simultaneous control of dozens of heat treatment processes.

Heatmasters Oy
Koneharjunkatu 6 Tel +358 3 882770
FIN-15860 Lahti Fax +358 3 8811770
Finland E-mail [email protected]

You might also like