T400HW03 V0 Auo

T400HW03 V0 Product Specification
更多屏规格书请登录【液晶仓库】 www.goodpanel.net Rev. 00
Model Name: T400HW03 V0

Issue Date : 2010/01/08
( )Preliminary Specifications
(＊
＊)Final Specifications
Customer Signature Date AUO Date
Approved By Approval By PM Director
Frank Hsu
_________________________________ ____________________________________
Note Reviewed By RD Director
Eugene CC Chen
____________________________________
Reviewed By Project Leader
Hank Chiu
____________________________________
Prepared By PM
Shelby Tong
____________________________________
© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 1 / 28

From 【液晶之家】— www.fpdclub.net
Contents
No
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
2 ABSOLUTE MAXIMUM RATINGS
3 ELECTRICAL SPECIFICATION
3-1 ELECTRIACL CHARACTERISTICS
3-2 INTERFACE CONNECTIONS
3-3 SIGNAL TIMING SPECIFICATION
3-4 SIGNAL TIMING WAVEFORM
3-5 COLOR INPUT DATA REFERENCE
3-6 POWER SEQUENCE
3-7 BACKLIGHT SPECIFICATION
4 OPTICAL SPECIFICATION
5 MECHANICAL CHARACTERISTICS
6 RELIABILITY TEST ITEMS
7 INTERNATIONAL STANDARD
7-1 SAFETY
7-2 EMC
8 PACKING
8-1 DEFINITION OF LABEL
8-2 PACKING METHODS
8-3 PALLET AND SHIPMENT INFORMATION
9 PRECAUTION
9-1 MOUNTING PRECAUTIONS
9-2 OPERATING PRECAUTIONS
9-3 ELECTROSTATIC DISCHARGE CONTROL
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE
9-5 STORAGE
9-6 HANDLING PRECAUTIONS FOR PROTECT FILM

Record of Revision
Version Date Page Description
0.0 2010/1/8 First release

1. General Description
This specification applies to the 40.0 inch Color TFT-LCD Module T400HW03 V0. This LCD module has a TFT
active matrix type liquid crystal panel 1,920x1,080 pixels, and diagonal size of 40.0 inch. T400HW03 V0 is a 40”
Full HD model plus high pin count series model, which is a high-end model for TV. The performance has the best
spec for technical exhibition & marketing promotion. A T400HW03 V0 model has high brightness, high contrast,
lower power consumption, less color wash-out, motion blur free, front mount bezel.
* General Information
Items Specification Unit Note

Active Screen Size 40.00 inch
Display Area (H)885.6mm x (V) 498.15mm mm
Outline Dimension 952x551x53.2 mm
Driver Element a-Si TFT active matrix
Display Colors 8 bit, 16.7M Colors
Number of Pixels 1,920x1,080 Pixel
Pixel Pitch 0.46125 (H) x 0.46125(W) mm
Pixel Arrangement RGB vertical stripe
Display Operation Mode Normally Black
Surface Treatment Anti-Glare Haze=11%

2. Absolute Maximum Ratings

The followings are maximum values which, if exceeded, may cause faulty operation or damage to the unit
Item Symbol Min Max Unit Conditions

Logic/LCD Drive Voltage VcDc -0.3 14 [Volt] Note 1
Input Voltage of Signal Vin -0.3 4 [Volt] Note 1
o
Operating Temperature TOP 0 +50 [ C] Note 2
Operating Humidity HOP 10 90 [%RH] Note 2
o
Storage Temperature TST -20 +60 [ C] Note 2
Storage Humidity HST 10 90 [%RH] Note 2
o
Panel Surface Temperature PST 65 [ C] Note 3
Note 1: Duration:50 msec.

Note 2 : Maximum Wet-Bulb should be 39 ℃ and No condensation.
The relative humidity must not exceed 90% non-condensing at temperatures of 40 ℃ or less. At temperatures
greater than 40℃, the wet bulb temperature must not exceed 39℃.
Note 3: Surface temperature is measured at 50℃ Dry condition

3. Electrical Specification
The T400HW03 V0 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT
array and liquid crystal. The second input for BLU is to power inverter.
3.1 Electrical Characteristics

Value
Parameter Symbol Unit Note
Min. Typ. Max
LCD
Power Supply Input Voltage VDD 10.8 12 13.2 VDC 1
Power Supply Input Current IDD 0.73 0.8 A 2
Power Consumption PC 8.76 9.6 Watt 2
Inrush Current IRUSH 4 A 3
Differential Input High Threshold Voltage VTH -- -- +100 mVDC 4
LVDS
Differential Input Low Threshold Voltage VTL -100 -- -- mVDC 4
Interface
Input Common Mode Voltage VICM 1.1 1.25 1.4 VDC 4
VIH
Input High Threshold Voltage 2.7 -- 3.3 VDC
CMOS (High)
Interface VIL
Input Low Threshold Voltage 0 -- 0.6 VDC
(Low)
Backlight Power Consumption PBL 114 120 126 Watt
Note :
1. The ripple voltage should be controlled under 10% of VCC
2. VDD = 12.0V, Fv = 60Hz, FCLK = 82MHz , 25 ℃, Test Pattern : White Pattern
3. Measurement condition : Rising time = 400us
VDD
90%
10%
GND
400 µs

4. VICM = 1.25V
V TH
V ICM
VTL
0V
3.2 Interface Connections

-LCD connector: FI-RE51S-HF (JAE, LVDS connector)
PIN Symbol Description PIN Symbol Description
1 VDD Power Supply, +12V DC Regulated 26 CH2_0+ LVDS Channel 2, Signal 0+
2 VDD Power Supply, +12V DC Regulated 27 CH2_1- LVDS Channel 2, Signal 1-
4 VDD Power Supply, +12V DC Regulated 29 CH2_2- LVDS Channel 2, Signal 2-
6 Reserved AUO Internal Use Only 31 GND Ground
7 GND Ground 32 CH2_CLK- LVDS Channel 2, Clock -
8 GND Ground 33 CH2_CLK+ LVDS Channel 2, Clock +
9 GND Ground 34 GND Ground
10 CH1_0- LVDS Channel 1, Signal 0- 35 CH2_3- LVDS Channel 2, Signal 3-
11 CH1_0+ LVDS Channel 1, Signal 0+ 36 CH2_3+ LVDS Channel 2, Signal 3+
12 CH1_1- LVDS Channel 1, Signal 1- 37 Reserved AUO Internal Use Only
13 CH1_1+ LVDS Channel 1, Signal 1+ 38 Reserved AUO Internal Use Only
14 CH1_2- LVDS Channel 1, Signal 2- 39 GND Ground
15 CH1_2+ LVDS Channel 1, Signal 2+ 40 SCL EEPROM Serial Clock
16 GND Ground 41 SDA EEPROM Serial Data
17 CH1_CLK- LVDS Channel 1, Clock - 42 NC No connection
EEPROM Write Protection
18 CH1_CLK+ LVDS Channel 1, Clock + 43 WP High(3.3V) for Writable,
Low(GND) for Protection
19 GND Ground 44 Panel_SEL reserve 0603 footprint of resistor to ground
Open/High(3.3V) for NS,
20 CH1_3- LVDS Channel 1, Signal 3- 45 LVDS_SEL
Low(GND) for JEIDA
Open/Low(GND): OD on,
21 CH1_3+ LVDS Channel 1, Signal 3+ 46 OD_SEL
High(3.3V): OD off
22 Reserved AUO Internal Use Only 47 NC No connection
23 Reserved AUO Internal Use Only 48 NC No connection
24 GND Ground 49 NC No connection

25 CH2_0- LVDS Channel 2, Signal 0- 50 TCON_RDY Connect 220ohm resistance to 3.3V

51 NC No connection
LVDS Option = High/OpenNS
P re vio u s C y cle C u rren t C yc le N e xt C yc le
C lo ck
C H x_0+ R1 R0 G0 R5 R4 R3 R2 R1 R0 G0
C H x_0-
C H x_1+ G2 G1 B1 B0 G5 G4 G3 G2 G1 B1
C H x_1-
C H x_2+
C H x_2- B3 B2 DE NA NA B5 B4 B3 B2 DE
C H x_3+
C H x_3- R7 R6 NA B7 B6 G7 G6 R7 R6 NA
LVDS Option = LowJEIDA

P re vio u s C yc le C u rren t C ycle N e x t C ycle
C lo ck
CH x_0+ R3 R2 G2 R7 R6 R5 R4 R3 R2 G2
CH x_0-
CH x_1+ G4 G3 B3 G7B 2 G7 G6 G5 G4 G3 B3
CH x_1-
CH x_2+
CH x_2- B5 B4 DE NA NA B7 B6 B5 B4 DE
CH x_3+
CH x_3- R1 R0 NA B1 B0 G1 G0 R1 R0 NA

3.3 Signal Timing Specification

This is the signal timing required at the input of the user connector. All of the interface signal timing should be
satisfied with the following specifications for its proper operation.
Timing Table
Signal Item Symbol Min. Typ. Max Unit

Period Tv 1090 1125 1480 Th
Vertical Section Active Tdisp (v) 1080 Th
Blanking Tblk (v) 10 45 400 Th
Period Th 1030 1100 1325 Tclk
Horizontal Section Active Tdisp (h) 960 Tclk
Blanking Tblk (h) 70 140 365 Tclk
Clock Frequency Fclk=1/Tclk 50 74.25 82 MHz
Vertical Frequency Frequency Fv 47 60 63 Hz
Horizontal Frequency Frequency Fh 60 67.5 73 KHz
Notes:
(1) Display position is specific by the rise of DE signal only.
st st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is displayed on the
left edge of the screen.
(2)Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of
st st
horizontal period. The 1 data corresponding to one horizontal line after the rise of 1 DE is displayed at the top
line of screen.
(3)If a period of DE “High” is less than 1920 DCLK or less than 1080 lines, the rest of the screen displays black.
(4)The display position does not fit to the screen if a period of DE “High” and the effective data period do not
synchronize with each other.

【液晶仓库】 www.goodpanel.net Rev. 00
Page 10 / 28
Tv M pixel
Tblk(v) Tdisp(v)
N L in e
Th
DE

RGB Line Invalid Data Line Line Line Line Line Invalid Data
N 1 2 3 4 N
Data
© Copyright AUO Optronics Corp. 2009 All Rights Reserved.

更多屏规格书请登录
CLK
Th
Tclk
Tdisp(h) Tblk(h)
DE
3.4 Signal Timing Waveforms
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
CH1 M-7 M-5 M-3 M-1
Invalid Data
1 3 5 7 9 11 M-5 M-3 M-1
Invalid Data
1 3
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
CH2 M-6 M-4 M-2 M
Invalid Data
2 4 6 8 10 12 M-4 M-2 M
Invalid Data
2 4
3.5 Color Input Data Reference

The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color;
the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.
COLOR DATA REFERENCE
Input Color Data

RED GREEN BLUE
Color
MSB LSB MSB LSB MSB LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Basic Blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Color Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RED(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
R ----
RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
G ----
GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
B ----
BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

3.6 Power Sequence for LCD
Values
Parameter Unit
Min. Type. Max.
t1 0.4 --- 30 ms
t2 0.1 --- --- ms
t3 300 --- --- ms
*1
t4 0 --- --- ms
t5 0 --- --- ms
*2
t6 --- --- --- ms
t7 500 --- --- ms
t2a 10 --- 100 ms
*3 *3
t2b 0 --- 100 ms
t2c 10 --- --- ms
Note:
(1) T4=0 : concern for residual pattern before BLU turn off.
(2) T6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)
(3) T2b : customer decide this value

3.7 Backlight Specification

The backlight unit contains 10-I type CCFLs (Cold Cathode Fluorescent Lamp)
3.7.1 Electrical specification
Spec
Item Symbol Condition Unit Note
Min Typ Max
1 Input Voltage VDDB - 21.6 24 26.4 VDC -
2 Input Current IDDB VDDB=24V 4.75 5 5.25 ADC 1
3 Input Power PDDB VDDB=24V 114 120 126 W 1
4 Inrush Current IRUSH VDDB=24V - - 6 ADC 2
ON 2 - 5.5 -
5 On/Off control voltage VBLON VDDB=24V VDC
OFF 0 - 0.8 -
6 On/Off control current IBLON VDDB=24V - - 1.5 mA -
MAX 3.0 - 3.3 VDC -

7 Dimming Control Voltage V_DIM VDDB=24V
MIN - 0 - VDC -
8 Dimming Control Current I_DIM VDDB=24V - - 2 mADC -
9 Internal Dimming Ratio DIM_R VDDB=24V 20 - 100 % 3
MAX VDDB=24V 2 - 3.3 -

External PWM
10 V_EPWM VDC
Control Voltage
MIN VDDB=24V -0.3 - 0.8 -
External PWM
11 I_EPWM VDDB=24V - - 2 mADC -
Control Current
12 External PWM Duty ratio D_EPWM VDDB=24V 5 - 100 % 3
External PWM
13 F_EPWM VDDB=24V 140 180 240 Hz -
Frequency
(
（ ℃
Note 1 : Dimming ratio= 100% (MAX) Ta=25±5 , Turn on for 45minutes ）
Note 2: Measurement condition Rising time = 20ms (VDDB : 10%~90%);
Note 3: Less than10% dimming control is functional well and no backlight shutdown happened

3.7.2 Input Pin Assignment
Inverter Connector: CI0114M1HRL-NH (Cvilux)
Pin Symbol Description
1 VDDB Operating Voltage Supply, +24V DC regulated
6 BLGND Ground and Current Return
BLU status detection:

11 DET
Normal : 0~0.8V ; Abnormal : Open collector
BLU On-Off control:
12 VBLON High/Open (2.4V~5.25V) : BL On ;
Low (0~0.8V/GND) : BL off
Internal PWM (0~3.3V for 10~100% Duty, open for 100%)

13 VDIM(**)
< NC ; at External PWM mode>
External PWM (5%~100% Duty, open for 100%)

14 PDIM(*)
< NC ; at Internal PWM mode>
(Note*) IF External PWM function includes 10% dimming ratio. Judge condition as below:
(1) Backlight module must be lighted ON normally.
(2) All protection function must work normally.
(3) Uniformity and flicker could NOT be guaranteed

3.7.3 Power Sequence for Inverter
24V(typ.)
90% 90%
10%
Power Input for BLU
(VDDB)
T1 T2 T5
Dimming Control Signal

(VDIM)
T3 T4
BLU On/Off Enable

(VBLON)
Dip condition for Inverter
Power Input for BLU

(VDDB) T6
VDDB(typ.)*0.8
Value
Parameter Units
Min Typ Max
T1 20 - - ms
T2 500 - - ms
T3 250 - - ms
T4 0 - - ms
T5 1 - - ms
T6 - - 10 ms

4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a
dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a
viewing angle of φ and θ equal to 0°.
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 4000 5000 -- 1
2
Surface Luminance (White) LWH 360 450 -- cd/m 2
Luminance Variation δWHITE(9P) -- -- 1.3 3
Response Time (G to G) Tγ -- 6.5 -- ms 4
Color Gamut NTSC 72 %
Color Coordinates
Red RX 0.640
RY 0.330
Green GX 0.290
GY 0.600
Typ.-0.03 Typ.+0.03
Blue BX 0.144
BY 0.060
White WX 0.280
WY 0.290
Viewing Angle 5
x axis, right(φ=0°) θr -- 89 -- degree
x axis, left(φ=180°) θl -- 89 -- degree
y axis, up(φ=90°) θu -- 89 -- degree
y axis, down (φ=270°) θd -- 89 -- degree
Note:

1. Contrast Ratio (CR) is defined mathematically as:
Surface Luminance of Lon5
Contrast Ratio=
Surface Luminance of Loff5
2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. From more information see FIG 2. When lamp current IH = 11mA. LWH=Lon5 where Lon5 is
the luminance with all pixels displaying white at center 5 location.
3. The variation in surface luminance, δWHITE is defined (center of Screen) as:
δWHITE(9P)= Maximum(Lon1, Lon2,…,Lon9)/ Minimum(Lon1, Lon2,…Lon9)
4. Response time T γ is the average time required for display transition by switching the input signal for five
luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=60Hz to optimize.
Measured Target
Response Time 0% 25% 50% 75% 100%
0% 0% to 25% 0% to 50% 0% to 75% 0% to 100%
25% 25% to 0% 25% to 50% 25% to 75% 25% to 100%
Start 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100%
75% 75% to 0% 75% to 25% 75% to 50% 75% to 100%
100% 100% to 0% 100% to 25% 100% to 50% 100% to 75%
4. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
more information see FIG4.
FIG. 2 Luminance
H/2 1 2 3
4 5 6 H
7 8
H/6
V/6 V/2

FIG.3 Response Time
The response time is defined as the following figure and shall be measured by switching the input signal for “any
level of grey(bright) “ and “any level of gray(dark)”.
Any level of gray (Bright) Any level of gray (Dark) Any level of gray (Bright)
0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100%
Photodetector
Output
0%, 25%, 50%, 75%, 100%

Time
T γ (F) T γ (R)
FIG.4 Viewing Angle

5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T400HW03 V0. In addition the figures in the
next page are detailed mechanical drawing of the LCD.
Horizontal 952.0 mm
Vertical 551.0 mm
Outline Dimension
Depth 53.2 mm
Horizontal 891.7 mm
Bezel Opening
Vertical 504.2 mm
Horizontal 885.6mm
Active Display Area
Vertical 498.15mm
Weight 7.3 Kg (Typ.)
Surface Treatment Anti-Glare(Haze=11%)

Front View

Back View

6. Reliability Test Items

Test Item Q’ty Condition
1 High temperature storage test 3 60℃, 300hrs
2 Low temperature storage test 3 -20℃ , 300hrs
3 High temperature operation test 3 50℃ , 300hrs
4 Low temperature operation test 3 -5℃ , 300hrs

Wave form: random
Vibration level: 1.5G RMS
5 Vibration test (non-operation) 3 Bandwidth: 10-300Hz,
Duration: X, Y, Z 30min
One time each direction

Shock level: 50G
6 Shock test (non-operation) 3 Waveform: half since wave, 11ms
Direction: ±X, ±Y, ±Z, One time each direction
Random wave (1.5G RMS, 10-200Hz)

7 Vibration test (With carton) 3
30mins/ Per each X,Y,Z axes
Height: 38.1cm
8 Drop test (With carton) 3 1 corner, 3 edges, 6 surfaces
(ASTMD4169-I)

7. International Standard
7.1 Safety
(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including
electrical Business Equipment.
(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical
Commission
(3) EN 60950 : 2001+A11, EN 60065:2002+A1:2006; European Committee for Electrotechnical
Standardization (CENELEC), EUROPEAN STANDARD for Safety of Information Technology
Equipment Including Electrical Business Equipment.
7.2 EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC),
1998

8. Packing
8-1 DEFINITION OF LABEL:
A. Panel Label:
*xxxxxxxxxxxx-xxxx*
AUO Internal Use

Panel Unique ID
AU Optronics
XXXXX Model NO: T400HW03 V.0 XXXXXXX

Manufactured XX/XX MADE IN XXXXX
AUO Internal Use Week Factory Location

Year AUO Internal Use
Green mark description
(1) For Pb Free Product, AUO will add for identification.
(2) For RoHs compatible products, AUO will add RoHS for identification.
Note: The green Mark will be present only when the green documents have been ready by AUO internal green
team. (definition of green design follows the AUO green design checklist.)
B. Carton Label:
QTY : 3
T400HW03 V0
97.40T04.000

8-2 PACKING METHODS:
瓦楞紙板

8-3 Pallet and Shipment Information

Specification Packing
Item
Qty. Dimension Weight (kg) Remark
1 Packing BOX 3pcs/box 1050(L)*280(W)*650(H) 27.4

2 Pallet 1 1140(L)*1060(W)*138(H) 16
3 Boxes per Pallet 8 boxes/pallet
4 Panels per Pallet 24pcs/pallet
Pallet after packing 24 1140(L)*1060(W)*1438(H) 235.2
Corner angle Moisture-proof film
Stretch film
Label PET band
Corner angle
Pallet

9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
9-1 MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. twisted stress) is not applied
to module. And the case on which a module is mounted should have sufficient strength so that
external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit
broken by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the
surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials
like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the
adhesives used to attach front/ rear polarizer. Do not use acetone, toluene and alcohol because
they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-2 OPERATING PRECAUTIONS

(1) The device listed in the product specification sheets was designed and manufactured for TV
application
(2) The spike noise causes the mis-operation of circuits. It should be lower than following voltage:
V=±200mV(Over and under shoot voltage)
(3) Response time depends on the temperature. (In lower temperature, it becomes longer..)
(4) Brightness of CCFL depends on the temperature. (In lower temperature, it becomes lower.) And in
lower temperature, response time (required time that brightness is stable after turned on) becomes
longer.
(5) Be careful for condensation at sudden temperature change. Condensation makes damage to
polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.
(6) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(7) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall
be done by system manufacturers. Grounding and shielding methods may be important to minimize
the interface.
9-3 ELECTROSTATIC DISCHARGE CONTROL
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain
that treatment persons are connected to ground through wristband etc. And don’t touch interface pin
directly.
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5 ℃ and 35℃ at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they
be stored in the container in which they were shipped.
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) The protection film is attached to the bezel with a small masking tape. When the protection film is
peeled off, static electricity is generated between the film and polarizer. This should be peeled off
slowly and carefully by people who are electrically grounded and with well ion-blown equipment or
in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a
very small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with
normal-hexane.


T400HW03 V0 Auo

Uploaded by

Copyright:

Available Formats

T400HW03 V0 Auo

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

T400HW03 V0 Auo

Uploaded by

Copyright:

Available Formats

T400HW03 V0 Product Specification

更多屏规格书请登录 【液晶仓库】 www.goodpanel.net Rev. 00

Model Name: T400HW03 V0

Customer Signature Date AUO Date

Approved By Approval By PM Director

Note Reviewed By RD Director

Reviewed By Project Leader

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 1 / 28

2 ABSOLUTE MAXIMUM RATINGS

3-1 ELECTRIACL CHARACTERISTICS

3-2 INTERFACE CONNECTIONS

3-3 SIGNAL TIMING SPECIFICATION

3-4 SIGNAL TIMING WAVEFORM

3-5 COLOR INPUT DATA REFERENCE

3-6 POWER SEQUENCE

3-7 BACKLIGHT SPECIFICATION

6 RELIABILITY TEST ITEMS

8-1 DEFINITION OF LABEL

8-2 PACKING METHODS

8-3 PALLET AND SHIPMENT INFORMATION

9-1 MOUNTING PRECAUTIONS

9-2 OPERATING PRECAUTIONS

9-3 ELECTROSTATIC DISCHARGE CONTROL

9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

9-6 HANDLING PRECAUTIONS FOR PROTECT FILM

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 2 / 28

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 3 / 28

Items Specification Unit Note

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 4 / 28

2. Absolute Maximum Ratings

Item Symbol Min Max Unit Conditions

Note 1: Duration:50 msec.

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 5 / 28

3.1 Electrical Characteristics

Differential Input High Threshold Voltage VTH -- -- +100 mVDC 4

Input Common Mode Voltage VICM 1.1 1.25 1.4 VDC 4

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 6 / 28

3.2 Interface Connections

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 7 / 28

25 CH2_0- LVDS Channel 2, Signal 0- 50 TCON_RDY Connect 220ohm resistance to 3.3V

LVDS Option = High/OpenNS

P re vio u s C y cle C u rren t C yc le N e xt C yc le

LVDS Option = LowJEIDA

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 8 / 28

3.3 Signal Timing Specification

Signal Item Symbol Min. Typ. Max Unit

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 9 / 28

From 【液晶之家】— www.fpdclub.net

© Copyright AUO Optronics Corp. 2009 All Rights Reserved.

3.5 Color Input Data Reference

COLOR DATA REFERENCE

Input Color Data

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 11 / 28

3.6 Power Sequence for LCD

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 12 / 28

3.7 Backlight Specification

3.7.1 Electrical specification

1 Input Voltage VDDB - 21.6 24 26.4 VDC -

2 Input Current IDDB VDDB=24V 4.75 5 5.25 ADC 1

更多屏规格书请登录【液晶仓库】 www.goodpanel.net Rev. 00

1 Packing BOX 3pcs/box 1050(L)280(W)650(H) 27.4