6.

Control Module I/O Signal

6. Control Module I/O Signal

G2M0446

Signal (V)
Connector Terminal
Content Ig SW Note
No. No. Engine ON (Idling)
OFF ON (Engine OFF)
Crankshaft Signal (+) E30 6 — 0 ±6 Sensor output waveform
position Signal (−) E30 7 — 0 0
sensor Shield E30 11 — 0 0
Camshaft Signal (+) E30 8 — 0 ±2.7 Sensor output waveform
position Signal (−) E30 9 — 0 0
sensor Shield E30 11 — 0 0
Mass air Signal E30 5 — 0 — 0.3 0.8 — 1.2 —
flow GND E31 1 — 0 0 —
sensor Shield E30 11 — 0 0 —
Fully closed: 0.2 — 1.0
Signal E30 4 — —
Throttle Fully opened: 4.2 — 4.5
position Power
E30 15 — 5 5 —
sensor supply
GND E30 11 — 0 0 —
Rich mixture: 0.7
Oxygen Signal E30 10 — 0
Lean mixture: 0
sensor
Shield E30 11 — 0 0 —
Engine coolant
E30 3 0 0.7 — 1.0 0.7 — 1.0 After warm-up
temperature sensor
“5” and “0” are
Vehicle speed sensor
E29 4 — 0 or 5 0 or 5 repeatedly displayed
2
when vehicle is driven.
49 states and Canada/
E31 7 — 0 0 —
California identification
Starter switch E29 12 — 0 0 Cranking: 10 to 14
ON: 10 — 13 ON: 13 — 14
A/C switch E29 11 — —
OFF: 0 OFF: 0
Ignition switch E29 10 0 10 — 13 13 — 14 —
! On MT model; switch
Neutral position switch
is ON when gear is in
(MT)
ON: 0 neutral position.
E29 16 —
OFF: 10 — 13 ! On AT model; switch
Park/Neutral position
is ON when shift is in
switch (AT)
“P” or “N” position.
Test mode connector E29 2 — 5 5 When connected: 0

16
 6. Control Module I/O Signal

Signal (V)
Connector Terminal
Content Ig SW Note
No. No. Engine ON (Idling)
OFF ON (Engine OFF)
Read memory
E29 19 — 5 5 When connected: 0
connector
When measuring
(AT) 5 (AT) 5
AT/MT identification E29 17 — voltage between ECM
(MT) 0 (MT) 0
and body.
Back-up power supply E29 26 10 — 13 10 — 13 13 — 14 —
Control unit power
E29 13 0 10 — 13 13 — 14 —
supply
Ignition # 1, # 2 E30 21 — 0 3.4, max. —
control # 3, # 4 E30 20 — 0 3.4, max. —
#1 E30 2 10 — 13 10 — 13 13 — 14 Waveform
Fuel #2 E30 1 10 — 13 10 — 13 13 — 14 Waveform
injector #3 E30 13 10 — 13 10 — 13 13 — 14 Waveform
#4 E30 12 10 — 13 10 — 13 13 — 14 Waveform
Idle air OPEN end E29 2 — — 1, max. — 13, min. Waveform
control
solenoid CLOSE
E29 1 — — 13, min. — 1, max. Waveform
valve end
Fuel pump relay ON: 0
E29 8 — 0 —
control OFF: 10 — 13
ON: 0 ON: 0
A/C relay control E29 9 — —
OFF: 10 — 13 OFF: 13 — 14
Radiator fan relay 1 ON: 0 ON: 0
E29 23 — —
control OFF: 10 — 13 OFF: 13 — 14
Radiator fan relay 2 ON: 0 ON: 0
E29 7 — —
control OFF: 10 — 13 OFF: 13 — 14
Self-shutoff control E29 18 — 10 — 13 13 — 14 —
Malfunction indicator Light “ON”: 1, max.
E29 22 — — —
lamp Light “OFF”: 10 — 14
Engine speed output E29 3 — — 0 — 13, min. Waveform
ON: 0 ON: 0
EGR solenoid valve E30 18 — —
OFF: 10 — 13 OFF: 13 — 14
Air suction solenoid ON: 0 ON: 0
E31 3 — —
valve OFF: 10 — 13 OFF: 13 — 14
ON: 0 ON: 0
FICD solenoid valve E29 24 — A/C equipped model
OFF: 10 — 13 OFF: 13 — 14
Purge control solenoid ON: 0 ON: 0
E30 19 — —
valve OFF: 10 — 13 OFF: 13 — 14
GND (sensors) E30 11 — 0 0 —
GND (injectors) E29 15 — 0 0 —
GND (ignition system) E29 14 — 0 0 —
GND (power supply) E29 25 — 0 0 —
GND (control systems) E30 22 — 0 0 —
E29 6 — — — —
Select Monitor Signal
E29 5 — — — —

17