0% found this document useful (0 votes)
394 views7 pages

PV Elite 2014 Licensee Filename: Rectangular Vessel Rectves Analysis: New Rectangular Item: 1 8:09P Aug 25,2015

This document provides the design specifications and stress analysis results for a new rectangular vessel. Key details include: - The vessel has a short side length of 266mm, long side length of 742mm, and minimum plate thickness of 8mm. - The design internal pressure is 0.03 bars and temperature is 50C. The material is SA-240 316L steel. - Stress analysis was performed according to the ASME Boiler and Pressure Vessel Code Section VIII Division 1. - Results show the membrane, bending, and total stresses are all below the allowable stress limits for the material at each location on the vessel.

Uploaded by

Pressure Vessel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
394 views7 pages

PV Elite 2014 Licensee Filename: Rectangular Vessel Rectves Analysis: New Rectangular Item: 1 8:09P Aug 25,2015

This document provides the design specifications and stress analysis results for a new rectangular vessel. Key details include: - The vessel has a short side length of 266mm, long side length of 742mm, and minimum plate thickness of 8mm. - The design internal pressure is 0.03 bars and temperature is 50C. The material is SA-240 316L steel. - Stress analysis was performed according to the ASME Boiler and Pressure Vessel Code Section VIII Division 1. - Results show the membrane, bending, and total stresses are all below the allowable stress limits for the material at each location on the vessel.

Uploaded by

Pressure Vessel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

PV Elite 2014 Licensee 1

FileName : rectangular vessel


Rectves Analysis : New Rectangular Item: 1 8:09p Aug 25,2015

Input Echo, COMPONENT 1, Description: New Rectangular

Figure Number Analyzed A5

Design Internal Pressure P 0.0300 bars

Design Temperature Temp 50.0000 C

VESSEL MATERIAL DATA:

Material Specification SA-240 316L

Shell Allowable Stress at Design Temp S 111.3559 N./mm^2

Shell Allowable Stress at Ambient SA 115.1465 N./mm^2

Shell Yield Stress at Design Temperature Sy 165.4004 N./mm^2

SHORT-SIDE VESSEL DATA:

Short-side Length Dimension L3 266.0000 mm.

Minimum Thickness of Short-side Plates t1 8.0000 mm.

Mid-side Joint Efficiency on Short-side E 0.8500

Corner Joint Efficiency on Short-side EC 0.8500

LONG-SIDE VESSEL DATA:

Long-side Length Dimension L4 742.0000 mm.

Minimum Thickness of Long-side Plates t2 8.0000 mm.

Mid-side Joint Efficiency on Long-side E 0.8500

ADDITIONAL VESSEL DATA:

Radius of Corner Sections R 75.0000 mm.

Minimum Thickness of End Plate t5 8.0000 mm.

C-Factor for End Plate Cf_Epl 0.2000

Corrosion Allowance of Shell CA 3.0000 mm.


PV Elite 2014 Licensee 2
FileName : rectangular vessel
Rectves Analysis : New Rectangular Item: 1 8:09p Aug 25,2015

REINFORCEMENT MATERIAL DATA:

Reinforcement Material Specification SA-240 316L

Reinf Allowable Stress at Design Temp Sr 111.3559 N./mm^2

Reinf Allowable Stress at Ambient SA 115.1465 N./mm^2

Reinf Yield Stress at Design Temp Sy 165.4004 N./mm^2

Pitch Distance for Reinforcement p 150.0000 mm.

C-Factor for Reinforcement (from UG-47) 2.1000

DELTA (Reinforcement Material Parameter) 485.0000 N./mm^2^0.5

SHORT-SIDE RECTANGULAR BEAM DATA:

Outside Distance from Outside of Vessel 1.0000 mm.

Length of Reinforcing Member 1.0000 mm.

Width of Reinforcing Member 1.0000 mm.

LONG-SIDE RECTANGULAR BEAM DATA:

Outside Distance from Outside of Vessel 135.0000 mm.

Length of Reinforcing Member 710.0000 mm.

Width of Reinforcing Member 8.0000 mm.

Rectangular Vessel Results, Item number 1, Desc: New Rectangular

ASME Code, Section VIII, Division 1, 2013 App. 13

REINFORCEMENT CALCULATIONS:

Maximum Distance B/W Reinforcing Members (Eq.(1) of UG-47):

pmax 1395.9281 mm.

Beta and J Values Taken from Table 13-8(d):

Short-side BETA = 0.2737

J = 2.0323

Long-side BETA = 0.9556


PV Elite 2014 Licensee 3
FileName : rectangular vessel
Rectves Analysis : New Rectangular Item: 1 8:09p Aug 25,2015

J = 4.5746

Max Pitch Values for Long and Short-sides Based on Equations (1a)-(1d)

from Section 13-8:

Short-side p1 = 5018.2046 mm.

Long-side p2 = 2155.9524 mm.

Maximum Pitch ( Minimum of p, p1, and p2 )

pmax = 1395.9281 mm.

Effective Width of Shell Plate at Locations where the Plate

is in Compression ( Section 13-8, Eq. (2) ):

w = 150.0000 mm.

Effective Width of Shell Plate at Locations where the Plate

is in Tension:

w = 150.0000 mm.

Effective Area of Reinforcement on Shell ( t * w ):

Short-side Ap = 7.5000 cm^2

Long-side Ap = 7.5000 cm^2

Moment of Inertia of Effective Area of Reinforcement ( w * t**3 / 12 ):

Short-side Is = 0.1562 cm**4

Long-side Il = 0.1562 cm**4

Moment of Inertia of Combined Reinforcement and Effective Width:

In Compression I11 = 0.1572 cm**4

I21 = 381.0661 cm**4

In Tension I11 = 0.1572 cm**4

I21 = 381.0661 cm**4


PV Elite 2014 Licensee 4
FileName : rectangular vessel
Rectves Analysis : New Rectangular Item: 1 8:09p Aug 25,2015

Distance from Neutral Axis of Cross Section of Composite Section to

the Inside Surface of the Vessel (mm.):

Ci Co

Short-side, in Compression 2.5040 -3.4960

in Tension 2.5040 -3.4960

Long-side, in Compression 43.8115 -96.1885

in Tension 43.8115 -96.1885

Rectangular Vessel Reinforcement Parameters:

In Compression,

K4 (Sec.13-8, Eqn.39) = -297.1001

Ma = p * P * K4 = -763.4359

Theta (Sec.13-8 ) = 15.9806

Mr (Sec.13-8, Eqn.38) = 278.7507

In Tension,

K4 (Sec.13-8, Eqn.39) = -297.1001

Ma = p * P * K4 = -763.4359

Mr (Sec.13-8, Eqn.38) = 278.7507

MEMBRANE STRESSES: Membrane Stress Calculations per Section 13-8,

Equations (21-23). (N./mm^2) :

STRESS LOCATIONS Actual Allowable

Long-side 1 at A 0.16 94.65

at B 0.16 111.36

at C 0.16 111.36

Long-side 2 at A 0.16 94.65

at B 0.16 111.36

at C 0.16 111.36

Short-side 1 at F 0.45 111.36

at G 0.45 111.36
PV Elite 2014 Licensee 5
FileName : rectangular vessel
Rectves Analysis : New Rectangular Item: 1 8:09p Aug 25,2015

at H 0.45 94.65

Short-side 2 at F 0.45 111.36

at G 0.45 111.36

at H 0.45 94.65

Corner Sections 0.46 94.65

BENDING STRESSES: Bending Stress Calculations per Section 13-8,

Equations (24-26). (N./mm^2) :

STRESS LOCATIONS Inner Outer Allowable

Long-side 1 at A -0.99 2.18 110.27

at B -92.64 92.64 167.03

at C 22.15 -22.15 167.03

Long-side 2 at A -0.99 2.18 110.27

at B -92.64 92.64 167.03

at C 22.15 -22.15 167.03

Short-side 1 at F 48.89 -48.89 167.03

at G 35.75 -35.75 167.03

at H 35.60 -49.71 110.27

Short-side 2 at F 48.89 -48.89 167.03

at G 35.75 -35.75 167.03

at H 35.60 -49.71 110.27

Corner Sections 50.39 -50.39 141.98

TOTAL STRESSES: Total Stress Calculations per Section 13-8,

Equations (31-37). (N./mm^2) :

STRESS LOCATIONS Inner Outer Allowable

Long-side 1 at A -0.83 2.34 110.27

at B -92.48 92.81 167.03

at C 22.32 -21.99 167.03

Long-side 2 at A -0.83 2.34 110.27

at B -92.48 92.81 167.03


PV Elite 2014 Licensee 6
FileName : rectangular vessel
Rectves Analysis : New Rectangular Item: 1 8:09p Aug 25,2015

at C 22.32 -21.99 167.03

Short-side 1 at F 49.33 -48.44 167.03

at G 36.20 -35.31 167.03

at H 36.05 -49.26 110.27

Short-side 2 at F 49.33 -48.44 167.03

at G 36.20 -35.31 167.03

at H 36.05 -49.26 110.27

Corner Sections 50.86 -49.93 141.98

END PLATE STRESSES (N./mm^2) :

Actual Allowable

End Plate 17.60 111.36

SUMMARY OF RESULTS:

MEMBRANE STRESS SUMMARY,

High Stress (Highest % of Allowable) 0.46 N./mm^2

High Stress Percentage 0.49 %

M.A.W.P. for Membrane Stresses 6.13 bars

BENDING STRESS SUMMARY,

High Stress (Highest % of Allowable) 92.64 N./mm^2

High Stress Percentage 55.46 %

M.A.W.P. for Bending Stresses 0.05 bars

TOTAL STRESS SUMMARY,

High Stress (Highest % of Allowable) 92.81 N./mm^2

High Stress Percentage 55.56 %

M.A.W.P. for Total Stresses 0.05 bars


PV Elite 2014 Licensee 7
FileName : rectangular vessel
Rectves Analysis : New Rectangular Item: 1 8:09p Aug 25,2015

PV Elite is a trademark of Intergraph CADWorx & Analysis Solutions, Inc. 2014

You might also like