Scribd
Upload
64 views12 pages

Lab Atm

This document describes the configuration of ATM interfaces on routers to establish connectivity between multiple networks. Key steps include: 1. Configuring ATM interfaces on each router with IP addresses for subinterfaces to connect local networks; 2. Configuring PVC connections on ATM subinterfaces to establish point-to-point links between routers; 3. Configuring RIP routing to exchange routes and enable connectivity between all connected networks.

Uploaded by

blbmalek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
64 views12 pages

Lab Atm

This document describes the configuration of ATM interfaces on routers to establish connectivity between multiple networks. Key steps include: 1. Configuring ATM interfaces on each router with IP addresses for subinterfaces to connect local networks; 2. Configuring PVC connections on ATM subinterfaces to establish point-to-point links between routers; 3. Configuring RIP routing to exchange routes and enable connectivity between all connected networks.

Uploaded by

blbmalek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 12

VPI default value de 0 au 8

VCI default value 32 au 67

Configuration du switch ATM

Topologie
Ici on a paramétré les routeurs avec des cartes réseaux Wan serial type ATM

Comment

On ajoute des cartes sur le slot 3 par exemple PA-A1

Et il faut que la version du IOS soit 12.4 (22)T pour une plate forme c7200

Et de même pour les autres routeurs

Configuration des routeurs


Configuration du R1

R1#conf t

Enter configuration commands, one per line. End with CNTL/Z.

R1(config)#interface ?

ATM ATM interface

Async Async interface

Auto-Template Auto-Template interface

BVI Bridge-Group Virtual Interface

CDMA-Ix CDMA Ix interface

CTunnel CTunnel interface

Dialer Dialer interface

FastEthernet FastEthernet IEEE 802.3

Group-Async Async Group interface

Lex Lex interface

Loopback Loopback interface

MFR Multilink Frame Relay bundle interface

Multilink Multilink-group interface

Null Null interface

Port-channel Ethernet Channel of interfaces

Tunnel Tunnel interface

Vif PGM Multicast Host interface

Virtual-PPP Virtual PPP interface

Virtual-Template Virtual Template interface

Virtual-TokenRing Virtual TokenRing

range interface range command

vmi Virtual Multipoint Interface


R1(config)#interface atm?

ATM

R1(config)#interface ATM ?

<0-7> ATM interface number

R1(config)#interface ATM 1/0

R1(config-if)#no shutdown

R1(config-if)#do show ip interface br

Interface IP-Address OK? Method Status Prot ocol

FastEthernet0/0 unassigned YES unset administratively down down

ATM1/0 unassigned YES unset up up

SSLVPN-VIF0 unassigned NO unset up up

R1(config-if)#exit

R1(config)#interface a1/0.1 ?

multipoint Treat as a multipoint link

point-to-point Treat as a point-to-point link

R1(config)#interface a1/0.1 m

R1(config)#interface a1/0.1 multipoint

R1(config-subif)#ip address 10.0.0.1 255.255.255.0

R1(config-subif)#pv

R1(config-subif)#pvc ?

<0-255> Enter VPI/VCI value(slash required)

<1-1023> Enter VCI value

WORD Optional handle to refer to this connection

R1(config-subif)#pvc 0/102

R1(config-if-atm-vc)#en

R1(config-if-atm-vc)#encapsulation ?

aal5mux AAL5+MUX Encapsulation


aal5nlpid AAL5+NLPID Encapsulation

aal5snap AAL5+LLC/SNAP Encapsulation

R1(config-if-atm-vc)#encapsulation aal5n

R1(config-if-atm-vc)#encapsulation aal5sn

R1(config-if-atm-vc)#encapsulation aal5snap

R1(config-if-atm-vc)#protocol ip ?

A.B.C.D Protocol specific address

inarp Use inarp on this protocol

R1(config-if-atm-vc)#protocol ip 10.0.0.2 ?

broadcast Pseudo-broadcast

no Prevent Pseudo-broadcast on this connection

<cr>

R1(config-if-atm-vc)#protocol ip 10.0.0.2 b

R1(config-if-atm-vc)#protocol ip 10.0.0.2 broadcast

R1(config-if-atm-vc)#exit

R1(config-subif)#pvc 0/103

R1(config-if-atm-vc)#enc

R1(config-if-atm-vc)#encapsulation aal5s

R1(config-if-atm-vc)#encapsulation aal5snap

R1(config-if-atm-vc)#pr

R1(config-if-atm-vc)#protocol ip 10.0.0.3 b

R1(config-if-atm-vc)#protocol ip 10.0.0.3 broadcast

R1(config-if-atm-vc)#exit

R1(config)# do show run

interface ATM1/0

no ip address

no atm ilmi-keepalive
interface ATM1/0.1 multipoint

ip address 10.0.0.1 255.255.255.0

pvc 0/102

protocol ip 10.0.0.2 broadcast

encapsulation aal5snap

pvc 0/103

protocol ip 10.0.0.3 broadcast

encapsulation aal5snap

R1(config)#interface fa0/0

R1(config-if)#ip address 192.168.1.1 255.255.255.0

R1(config-if)#no shutdown

configuration de R2

R2(config)#interface a1/0

R2(config-if)#no shutdown

R2(config-if)#

*Jun 9 20:49:15.919: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up

*Jun 9 20:49:16.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, ch


anged state to up

R2(config-if)#exit

R2(config)#interface a1/0.1 poi

R2(config)#interface a1/0.1 point-to-point

R2(config-subif)#ip address 10.0.0.2 255.255.255.0

R2(config-subif)#enc

R2(config-subif)#enca

R2(config-subif)#pvc 0/201

R2(config-if-atm-vc)#enc

R2(config-if-atm-vc)#encapsulation aal5s
R2(config-if-atm-vc)#encapsulation aal5snap

R2(config-if-atm-vc)#exit

R2(config-subif)#exit

R2(config)#exit

*Jun 9 20:57:06.719: %SYS-5-CONFIG_I: Configured from console by console

R2(config)#interface f0/0

R2(config-if)#ip address 192.168.2.1 255.255.255.0

R2(config-if)#no shutdown

Test de la connectivite

R2#ping 10.0.0.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 20/32/56 ms

R2#

configuration de R3

R3#conf t

Enter configuration commands, one per line. End with CNTL/Z.

R3(config)#interface a1/0

R3(config-if)#no shutd

R3(config-if)#exit

*Jun 9 21:01:41.159: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up

*Jun 9 21:01:42.159: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0,


changed state to up

R3(config-if)#exit

R3(config)#interface a1/0.1 p

R3(config)#interface a1/0.1 point-to-point

R3(config-subif)#ip address 10.0.0.3 255.255.255.0


R3(config-subif)#pvc 0/301

R3(config-if-atm-vc)#enc

R3(config-if-atm-vc)#encapsulation aal5s

R3(config-if-atm-vc)#encapsulation aal5snap

R3(config-if-atm-vc)#

R3(config-if-atm-vc)#

R3(config-if-atm-vc)#

R3(config-if-atm-vc)#end

*Jun 9 21:04:22.535: %SYS-5-CONFIG_I: Configured from console by console

R3(config)#interface fa0/0

R3(config-if)#ip address 192.168.4.1 255.255.255.0

R3(config-if)#no shutdown

R3(config-if)#do copy r s

Test de la connectivite

R3#ping 10.0.0.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 8/24/64 ms

R3#traceroute 10.0.0.1

Type escape sequence to abort.

Tracing the route to 10.0.0.1

1 10.0.0.1 16 msec 52 msec 40 msec

R3#traceroute 10.0.0.2

Type escape sequence to abort.


Tracing the route to 10.0.0.2

1 10.0.0.1 4 msec 32 msec 20 msec

2 10.0.0.2 48 msec 40 msec 32 msec

Configuration du routage

Routeur R1

R1(config)#router rip

R1(config-router)#version 2

R1(config-router)#network 192.168.1.0

R1(config-router)#network 10.0.0.0

R1(config-router)#no aut

R1(config-router)#no auto-summary

R1(config-router)#

R1(config-router)#do copy r s

Routeur R2

R2(config)#router rip

R2(config-router)#version 2

R2(config-router)#ne

R2(config-router)#net

R2(config-router)#network 192.168.2.0

R2(config-router)#network 10.0.0.0

R2(config-router)#noa

R2(config-router)#no a

R2(config-router)#no au

R2(config-router)#no auto-summary

R2(config-router)#do copy r s

Destination filename [startup-config]?


Routeur R3

R3(config)#router rip

R3(config-router)#version 2

R3(config-router)#net

R3(config-router)#network 192.168.4.0

R3(config-router)#network 10.0.0.0

R3(config-router)#no aut

R3(config-router)#no auto-summary

R3(config-router)#end

R3#copy r s

Test de connectivite a partire du windows7

windows7> ping 192.168.1.1

84 bytes from 192.168.1.1 icmp_seq=1 ttl=255 time=19.001 ms

84 bytes from 192.168.1.1 icmp_seq=2 ttl=255 time=6.000 ms

84 bytes from 192.168.1.1 icmp_seq=3 ttl=255 time=2.000 ms

84 bytes from 192.168.1.1 icmp_seq=4 ttl=255 time=10.001 ms

84 bytes from 192.168.1.1 icmp_seq=5 ttl=255 time=10.001 ms

windows7> ping 10.0.0.2

84 bytes from 10.0.0.2 icmp_seq=1 ttl=255 time=7.000 ms

84 bytes from 10.0.0.2 icmp_seq=2 ttl=255 time=8.000 ms

84 bytes from 10.0.0.2 icmp_seq=3 ttl=255 time=8.001 ms

84 bytes from 10.0.0.2 icmp_seq=4 ttl=255 time=4.000 ms

84 bytes from 10.0.0.2 icmp_seq=5 ttl=255 time=2.000 ms

windows7> ping 10.0.0.1

84 bytes from 10.0.0.1 icmp_seq=1 ttl=254 time=27.001 ms

84 bytes from 10.0.0.1 icmp_seq=2 ttl=254 time=13.001 ms

84 bytes from 10.0.0.1 icmp_seq=3 ttl=254 time=13.001 ms


84 bytes from 10.0.0.1 icmp_seq=4 ttl=254 time=27.002 ms

84 bytes from 10.0.0.1 icmp_seq=5 ttl=254 time=14.001 ms

windows7> ping 192.168.1.1

84 bytes from 192.168.1.1 icmp_seq=1 ttl=255 time=2.000 ms

84 bytes from 192.168.1.1 icmp_seq=2 ttl=255 time=10.001 ms

84 bytes from 192.168.1.1 icmp_seq=3 ttl=255 time=5.000 ms

84 bytes from 192.168.1.1 icmp_seq=4 ttl=255 time=7.001 ms

84 bytes from 192.168.1.1 icmp_seq=5 ttl=255 time=2.000 ms

Du pc windows 7 vers pc server

windows7> ping 192.168.4.10

84 bytes from 192.168.4.10 icmp_seq=1 ttl=62 time=45.002 ms

84 bytes from 192.168.4.10 icmp_seq=2 ttl=62 time=29.002 ms

84 bytes from 192.168.4.10 icmp_seq=3 ttl=62 time=29.002 ms

84 bytes from 192.168.4.10 icmp_seq=4 ttl=62 time=23.001 ms

84 bytes from 192.168.4.10 icmp_seq=5 ttl=62 time=27.001 ms

Du pc windows 7 vers pc windows 8

windows7> ping 192.168.2.10

84 bytes from 192.168.2.10 icmp_seq=1 ttl=61 time=101.006 ms

84 bytes from 192.168.2.10 icmp_seq=2 ttl=61 time=47.003 ms

84 bytes from 192.168.2.10 icmp_seq=3 ttl=61 time=36.002 ms

84 bytes from 192.168.2.10 icmp_seq=4 ttl=61 time=37.002 ms

84 bytes from 192.168.2.10 icmp_seq=5 ttl=61 time=38.003 ms

You might also like