ROUTER BIT GUIDE 800-645-5555

www.klingspor.com
KLINGSPOR is pleased to offer one of the finest lines of router
bits and accessories available to the industrial market. These
bits offer exceptional quality for long-lasting use and clean cuts.

What makes KLINGSPOR bits better than other

bits on the market?

1. Thick Carbide for extra sharpenings

2. Highest quality micrograin carbide
3. Made from solid alloy steel
4. Precision ground for proper balance
at high RPM’s
5. High hook and relief angles for better
chip ejection
6. Superior edge quality
All of these components add up to the best bits you can buy anywhere.

PRODUCT GUARANTEE
All KLINGSPOR bits are warranted to be free from defects in workmanship or materi-
als. Warranty is void if tools are altered in any way. Always read and follow owner’s
safety manual of all power machinery before using bits. Always use eye protection
while using this or any carbide cutting product. WARNING: Re-grinding of this prod- SPIRAL BITS STRAIGHT BITS
uct will produce dust of potentially hazardous ingredients. ADVANTAGES ADVANTAGES
• Very clean cut • Wide variety of lengths and diam-
Tool Diameter Max R.P.M. Recommended • More cutter in wood means less eters
1/16" to 1/4" 24000 18000 to 21000 vibration • Less expensive
5/16" to 1" 21000 18000 • Better plunge-cutting • Greater ability to resharpen
1" to 2¼" 18000 16000 • Can be used on more machinery
2¼" to 2¾" 14000 to 16000 14000 (CNC, Table, & hand router) DISADVANTAGE
• Direct chips up or down • Plunge-cutting requires more effort
3" to 3¾" 8000 to 12000 10000
• Longer edgewear and skill
If you can run with less rpm and get a satisfactory cut, run less. • Solid carbide instead of tipped
WARNING: KLINGSPOR products can expose you to chemicals including lead and/or cobalt, which are
known to the State of California to cause cancer and birth defects or other reproductive harm. For more DISADVANTAGES *Pay attention to the special use section
information go to http://www.P65Warnings.ca.gov. • Limited lengths and diameters throughout the catalog as that will
WARNING: Drilling, sanding or machining wood products can expose you to wood dust, a substance • Can be somewhat risky to use as they denote specific uses of certain bits and
known to the State of California to cause cancer. Avoid inhaling wood dust or use a mask or other are less flexible direct replacements.
safeguards for personal protection. For more information go to http://www.P65Warnings.ca.gov.

TERMS AND CONDITIONS

TERMS: Minimum $50.00 order. Net 30 days from date of invoice. Invoices not paid within terms will be considered delinquent, and any orders will
be placed on hold until delinquent invoices are paid.
ROUTER
DELIVERY: Single order shipments to one destination totaling $300.00 or more will be shipped F.O.B. destination via carrier of our choice, continen-
tal U.S. only. Orders under $300.00 will be shipped F.O.B. KLINGSPOR Distribution Point, continental U.S. only.
ALASKA & HAWAII SHIPMENTS: Shipments to Alaska or Hawaii will be prepaid only to the point of embarkation within the continental U.S.,
provided above conditions are met. NOTE: KLINGSPOR ABRASIVES cannot be held accountable for delays once an order is released to a carrier.
QUANTITY VARIANCE: Because of the nature of the manufacturing process, a ±10% variance will be allowed by the buyer to the manufacturer.
PRICING: All prices in this catalog are subject to correction and change without notice. All computer invoice extensions have been calculated utiliz-
ROUTER
ing two decimal places; therefore, there is the possibility that variations, however minor, may occur due to rounding, and shall be allowed by the buyer. TABLE
RETURN POLICY: Returns of merchandise will be accepted only with prior return authorization. Custom size items cannot be returned. All products
authorized for return must be properly packaged and returned freight prepaid and in original packaging in re-sellable condition. We are not respon-
sible for items ordered in error or overstocked; if any exceptions are made, a 15% restocking fee will apply. Material non-refundable after one year.
PRODUCT WARRANTY: KLINGSPOR ABRASIVES, Inc. warrants all products to be free from defects for up to one year. If any KLINGSPOR
products are found to be defective, buyer’s sole and exclusive remedy will be the replacement of any such products or, at KLINGSPOR’s option, the
CNC
refund of buyer’s purchase price for said products. In any event, KLINGSPOR shall not be liable for any consequential damages. MACHINE

ROUTER BITS 2 Call Toll Free 800-645-5555

 SIGN MAKING / CNC

BALLNOSE SPIRAL CARVING LINER

The upcut ballnose spiral bit is good for blind holes where you want the chips to be removed Carving Liner is specially designed for producing extra fine vein point for carving or lettering details.
up and out of the hole. The “ballnose" is beneficial on CNC milling applications where 3D Due to the delicate nature of the profile great care should be used when running this bit. Point Length
routing or carving is required, or for routing slots on inside corners with a radius, concave refers to the depth of cut from the corner of the shoulder to the bit tip. Solid carbide. Double fluted.
geometry. PART CUTTING SHANK OVERALL
• Precision 2D and 3D large scale carving NUMBER ANGLE LENGTH DIAMETER LENGTH
• Dimensional signage
• 3D millwork SC50 10.5˚ 5/8" 1/4" 2 1/2"
• 2D and 3D contouring, profiling, modeling and pattern making for cabinetry,
sign making, furniture making and jewelry mold making
• Compatible with CarveWright™ and CompuCarve woodworking systems
• Perfect for model-makers on large 3D milling profiles in abrasive EPS foam and other materials
CUT CUTTING SHANK OVERALL
PART # RADIUS DIAMETER LENGTH LENGTH ROUND NOSE
SC64 1/32" 1/16" 3/4" 1/4" 2 1/2" With Bearing Guide The addition of a shank mounted bearing extends the use of
SC66 1/16" 1/8" 3/4" 1/4" 2 1/2" our round nose bits in lettering, veining, or decorative cuts when following a template.
RU1800RN 3/32" 3/16" 3/4" 1/4" 2 1/2" PART CUTTING CUTTING BEARING
RU2075RN 1/8" 1/4" 3/4" 1/4" 2 1/2" NUMBER RADIUS DIAMETER LENGTH NUMBER
RU5125RN 1/4" 1/2" 1 1/4" 1/2" 3" 1/4" SHANK
RUB5200 1/4" 1/2" 2" 1/2" 4" 1404B 1/4" 1/2" 5/8" B9
* Sets available on page 39 1405B 5/16" 5/8" 3/8" B6
1406B 3/8" 3/4" 7/16" B4

O-FLUTE SPIRAL BITS

Up Cut or Down Cut Solid Carbide
- Slow Spiral Used primarily for routing plastics
O-flute bits (straight or spiral) are ideal for working with plastics, thin aluminum (ACM), other soft
Point Length
metals, and starboard. The spiral O-flute evacuates shavings much more efficiently than the straight
version. RU2074A has a special High polish grind applied for extra life and performance.
V GROOVE UP CUT DOWN CUT CUTTING CUTTING SHANK OVERALL
V Groove bits are available in a variety of angles. They cut deep or shallow “V" grooves. These bits PART # PART # DIAMETER LENGTH DIAMETER LENGTH
are great for sign making or for adding decorative accents to furniture and plaques. Carbide tipped. SINGLE FLUTE
Two-wing cutter. RU1581A 1/8" 1/4" 1/4" 2"
PART CUTTING POINT OVERALL RU1601A 1/8" 1/2" 1/4" 2 1/2"
NUMBER DIAMETER LENGTH ANGLE LENGTH RU1701A 5/32" 5/8" 1/4" 2 1/2"
RU1801A 3/16" 5/8" 1/4" 2 1/2"
1/4" SHANK RU2074A RD2074A 1/4" 3/4" 1/4" 2 1/2"
SC 1500 1/4" 1/8" 90˚ 1 1/2" RU2111A 1/4" 1-1/8" 1/4" 3"
1501 3/8" 3/16" 90˚ 1 7/8" RU4111A 3/8" 1-1/8" 3/8" 3"
1502 1/2" 1/4" 90˚ 1 7/8" RU5121A 1/2" 1-1/4" 1/2" 3"
SC 1540 1/4" 7/32" 60˚ 1 1/2" RU5161A 1/2" 1-5/8" 1/2" 3 1/2"
* SC 1541 1/4" 7/32" 60˚ 2" RU5201A 1/2" 2" 1/2" 4"
1550 1/2" 7/16" 60˚ 2" DOUBLE FLUTE
1/2" SHANK RU2076A RD2076A 1/4" 3/4" 1/4" 2 1/2"
1503 1/2" 1/4" 90˚ 2"
1504 3/4" 3/8" 90˚ 2 1/4"
1506 1" 1/2" 90˚ 2 1/4"
1508 1 1/2" 3/4" 90˚ 2 5/8"
1560 1/2" 7/16" 60˚ 2 1/4"
1/2" SHANK
O - FLUTE STRAIGHT BITS
15-238 1-1/4" 1/2" 110˚ 2 3/16"
Solid Carbide - One Flute Used primarily
15-240 1-1/4" 1/4" 130˚ 2 3/16"
for routing plastics
15-241 1-1/4" 3/16" 150˚ 2 3/16" PART CUTTING CUTTING SHANK OVERALL
1508-91Q 1 1/2" 3/4" 91˚ 2 1/2" NUMBER DIAMETER LENGTH DIAMETER LENGTH
SA1600 1/8" 3/8" 1/4" 2 1/2"
SC - Solid Carbide Not for miter folding. SA1700 5/32" 1/2" 1/4" 2 1/2"
* #1541 features three flutes for improved veining SA1800 3/16" 1/2" 1/4" 2 1/2"
SA1900 7/32" 5/8" 1/4" 2 1/2"
SA2075 1/4" 3/4" 1/4" 2 1/2"
SA2100 1/4" 1" 1/4" 3 1/2"
SA4100 3/8" 1" 3/8" 3"
LH Rotation available by request.

Visit us online: www.klingspor.com 3 ROUTER BITS

 SOLID CARBIDE SPIRALS

CHIPBREAKER SPIRAL BITS

STANDARD Up Cut or Down Cut Solid Carbide
SPIRAL BITS - Two Flute Chipbreaker Spiral bits are the same as a standard up or down spiral, but they are
Up Cut or Down Cut Solid Carbide - Two Flute
designed to break up the chips as the bit cuts the wood.
Solid Carbide spiral bits are available in up, down, or up/down configuration, left or right (most will be
right), in one, two or three flutes, and in 1 /4", 5/16", 3/8", 1/2", 5/8" or 3/4" shank. UP CUT DOWN CUT CUTTING CUTTING OVERALL
PART # PART # DIAMETER LENGTH LENGTH
Upcut bits are good for blind holes where you want the chips to be removed up and out of the hole.
The only problem with this is that same up cut motion can also cause the top surface to splinter up 1/2" SHANK
creating a chipped surface. If you were using the same bit on the edge of a piece of wood the bottom RU5125CB RD5125CB 1/2" 1 1/4" 3"
edge would be nice and clean because the “up" shearing action of the bit. RU5150CB RD5150CB 1/2" 1 1/2" 3 1/2"
RU5200CB RD5200CB 1/2" 2" 4"
With a downcut bit you would have the opposite scenario from an upcut. The top would be clean and
the bottom might be slightly splintered. Downcut bits are great for cutting dadoes and grooves. The The above items are available from stock with chipbreakers. Chipbreakers can be
top edges remain clean during the routing process. A slower feed rate is recommended when using a added to any Spiral Bits by request.
downcut spiral bit.

UP CUT DOWN CUT CUTTING CUTTING OVERALL

PART # PART # DIAMETER LENGTH LENGTH
1/4" SHANK
RU1600 RD1600 1/8" 1/2" 2"
RU1700 RD1700 5/32" 5/8" 2"
RU1800 RD1800 3/16" 3/4" 2 1/2"
RU1805 RD1805 5mm 3/4" 2 1/2"
RU1900 RD1900 7/32" 3/4" 2 1/2"
RU2075 RD2075 1/4" 3/4" 2 1/2" FLUSH TRIM SPIRAL BITS
RU2100 RD2100 1/4" 1" 2 1/2" These spiral bits offer State-of-the-Art results in Flush trimming. Our 1/4" diameter tools are great for
5/16" SHANK small inside corners. Try our 1/8" diameter for extremely sharp corners. The 1/8" bit uses a solid pilot. All
RU3100 RD3100 5/16" 1" 2 1/2" others feature a double ball bearing guide. Available in your choice of Up Cut, Down Cut, or an Up/Down
3/8" SHANK Combination. Flush trim spirals are great for following a pattern or template. They have a heavy duty
RU4075 RD4075 3/8" 3/4" 2 1/2" bearing on the end and leave the edge much smoother than the straight bit counterpart due to having
RU4100 RD4100 3/8" 1" 2 1/2"
a cutting surface in the material at all times.
RU4125 RD4125 3/8" 1 1/4" 3"
• HU4125 • HD4125 3/8" 1 1/4" 3" UP CUT DOWN CUT CUTTING CUTTING OVERALL
1/2" SHANK PART # PART # DIAMETER LENGTH LENGTH
RU4675 RD4675 1/4" 3/4" 3"
1/4" SHANK
RU4700 RD4700 1/4" 1" 3 1/4" RFT1600 RFTD1600 1/8" 3/8" 2"
RU4800 RD4800 9/32" 1" 3" RFT2100 RFTD2100 1/4" 1" 3"
RU4850 RD4850 5/16" 1" 3"
RU4875 RD4875 3/8" 3/4" 3" 1/2" SHANK
RU4900 RD4900 3/8" 1 1/4" 3" RFT5125 RFTD5125 1/2" 1 1/4" 3 3/4"
RU4950 RD4950 7/16" 1 1/4" 3" RFT5200 RFTD5200 1/2" 2" 4 3/4"
RU5100 RD5100 1/2" 1" 3"
* RU5125 RD5125 1/2" 1 1/4" 3"
• HU5125 • HD5125 1/2" 1 1/4" 3" UDP = Pattern
RU5150 RD5150 1/2" 1 1/2" 3 1/2" UDC = Combo top/bottom
* RU5200 RD5200 1/2" 2" 4" UDFT = Flush Trim
5/8" SHANK
RU6150 RD6150 5/8" 1 1/2" 3 1/2"
RU6200 RD6200 5/8" 2" 4"

RU7150 RD7150
3/4" SHANK
3/4" 1 1/2" 4"
FLUSH TRIM UP/DOWN CUT SPIRAL
RU7200 RD7200 3/4" 2" 4"
Up/Down Cut (2+2 Compression) Solid Carbide
RU7300 RD7300 3/4" 3" 5" - Two Flute
RU7306 RD7306 3/4" 3" 6" PART CUTTING CUTTING SHANK OVERALL
* Ballnose available - see page 3 • HU/HD = Hard Carbide NUMBER DIAMETER LENGTH DIAMETER LENGTH
UDFT5152 1/2" 1 1/2" 1/2" 4 1/4"
* UDP9112 7/8" 1 1/8" 1/2" 4"
* UDC9112 7/8" 1 1/8" 1/2" 4"
* UDFT9112 7/8" 1 1/8" 1/2" 4"
* Solid carbide spiral brazed to a steel shank

ROUTER BITS 4 Call Toll Free 800-645-5555

 SOLID CARBIDE SPIRALS
UP/DOWN CUT SPIRAL BITS
Compression Bits give you the best of both worlds. The part of the
spiral bit closest to the tip has a 3/8" upcut and the part closest to the
LEFT HAND SPIRAL BITS router is downcut. It compresses the chips to the center of the bit.
This is especially good for plywood, laminates, and MDF when you
Up Cut or Down Cut Solid Carbide - Two Flute need the top and bottom edges clean. Choosing the right length of bit is
UP CUT DOWN CUT CUTTING CUTTING OVERALL important to match the thickness of material you are cutting, so both ends of the bit have room to work.
PART # PART # DIAMETER LENGTH LENGTH The “M" denotes that the bit has a mortise cut, which provides a 1/4" upcut before the downcut
begins. This allows the cutter to create a shallower groove/dado cut for denser or easily chipped material.
1/4" SHANK “HC" denotes a super hard Carbide, which provides much longer life when used on laminates and
LU1600 LD1600 1/8" 1/2" 2" melamine. Speeds & feed rates must be reduced when using these bits due to the brittleness of the
LU1800 LD1800 3/16" 3/4" 2" harder carbide.
LU2100 LD2100 1/4" 1" 2 1/2" “K" refers to our nano coating technology which increases life and allows for increased feed rates on
5/16" SHANK high production applications.
LU3100 LD3100 5/16" 1" 3"
3/8" SHANK Up/Down Cut (1+1 Compression) Solid Carbide - Single Flute
LU4100 LD4100 3/8" 1" 3" PART CUTTING CUTTING SHANK OVERALL
1/2" SHANK NUMBER DIAMETER LENGTH DIAMETER LENGTH
LU5125 LD5125 1/2" 1 1/4" 3" UD2100 1/4" 1" 1/4" 2 1/2"
LU5200 LD5200 1/2" 2" 4" UD4125 3/8" 1 1/4" 3/8" 3"
5/8" SHANK UD5150 1/2" 1 1/2" 1/2" 3 1/2"
LU6200 LD6200 5/8" 2" 4" UD5160 1/2" 1 5/8" 1/2" 3 1/2"
3/4" SHANK Up/Down Cut (2+2 Compression) Solid Carbide - Two Flute
LU7200 LD7200 3/4" 2" 4"
PART CUTTING CUTTING SHANK OVERALL
NUMBER DIAMETER LENGTH DIAMETER LENGTH
UD1602 1/8" 1/2" 1/4" 2 1/2"
UD2102 1/4" 1" 1/4" 2 1/2"
* UD4102M 3/8" 1" 3/8" 2 1/2"
UD4122 3/8" 1 1/4" 3/8" 3"
* UD4122M 3/8" 1 1/4" 3/8" 3"
† UD4122M-K 3/8" 1 1/4" 1/2" 3"
• HC4122M 3/8" 1 1/4" 3/8" 3"
ROUGHING SPIRAL BITS UD5122 1/2" 1 1/4" 1/2" 3"
* UD5122M 1/2" 1 1/4" 1/2" 3"
(Hoggers) Up Cut or Down Cut Solid Carbide - Three Flute † UD5122M-K 1/2" 1 1/4" 1/2" 3"
Roughing Spiral bits are the go to for material removal. They are known as the “hoggers". The edges • HC5122M 1/2" 1 1/4" 1/2" 3"
have serrations milled into them to break up the chips into smaller pieces and really move some UD5152 1/2" 1 1/2" 1/2" 3 1/2"
material fast when cutting. UD5162 1/2" 1 5/8" 1/2" 3 1/2"
UP CUT DOWN CUT CUTTING CUTTING SHANK OVERALL * UD5162M 1/2" 1 5/8" 1/2" 3 1/2"
PART # PART # DIAMETER LENGTH DIAMETER LENGTH UD5202 1/2" 2" 1/2" 4"
UD6152 5/8" 1 1/2" 5/8" 4"
* RU4000H 3/8" 1" 3/8" 2 1/2"
UD7152 3/4" 1 1/2" 3/4" 4"
RU4100H RD4100H 3/8" 1" 3/8" 3"
UD7202 3/4" 2" 3/4" 5"
RU4125H RD4125H 3/8" 1 1/4" 3/8" 3"
RU5125H RD5125H 1/2" 1 1/4" 1/2" 3" Up/Down Cut (3+3 Compression) Solid Carbide - Three Flute
RU5162H RD5162H 1/2" 1 5/8" 1/2" 3 1/2"
PART CUTTING CUTTING SHANK OVERALL
RU5218H RD5218H 1/2" 2 3/16" 1/2" 4" NUMBER DIAMETER LENGTH DIAMETER LENGTH
RU6200H RD6200H 5/8" 2" 5/8" 4" * UD4123M 3/8" 1 1/4" 3/8" 3"
RU7200H RD7200H 3/4" 2" 3/4" 4" UD5123 1/2" 1 1/4" 1/2" 3"
RU7325H RD7325H 3/4" 3 1/4" 3/4" 6" * UD5123M 1/2" 1 1/4" 1/2" 3"
*For Castle & P-C Pocket Machines.
UD5143 1/2" 1 3/8" 1/2" 3 1/2"
UD5163 1/2" 1 5/8" 1/2" 3 1/2"
* UD5163M 1/2" 1 5/8" 1/2" 3 1/2"
* Mortise Style - These bits have a short 1/4" up-cut end flute. This allows down shear
cutting action to the top edge during shallow cuts.
• Super Hard Carbide versions for use on melamine and for extra life.
† Nano coating for increased feed rates.

THREE FLUTE SPIRAL BITS SLOW SPIRAL BITS

Up Cut or Down Cut Solid Carbide - Three Flute Up Cut or Down Cut Solid Carbide - Three Flute
Slow Spiral bits have less of a twist than the full spirals, which makes
UP CUT DOWN CUT CUTTING CUTTING SHANK OVERALL
PART # PART # DIAMETER LENGTH DIAMETER LENGTH them ideal for use on hardwoods, solid surface, and hard plastics.
RU4125T RD4125T 3/8" 1 1/4" 3/8" 3" UP CUT DOWN CUT CUTTING CUTTING SHANK OVERALL
RU5125T RD5125T 1/2" 1 1/4" 1/2" 3" PART # PART # DIAMETER LENGTH DIAMETER LENGTH
RU5200T RD5200T 1/2" 2" 1/2" 4" RU4100S RD4100S 3/8" 1" 3/8" 2 1/2"
RU7200T RD7200T 3/4" 2" 3/4" 4" RU5100S RD5100S 1/2" 1" 1/2" 3"
RU5150S RD5150S 1/2" 1 1/2" 1/2" 3 1/2"

Visit us online: www.klingspor.com 5 ROUTER BITS

 SOLID CARBIDE
Straight Carbide Tipped bits (left & right hand) are the standard in the woodworking industry
and are an economical version of the spirals. They are offered in more sizes and cutting
lengths than their spiral counterparts and available in 1/4", 3/8", and 1/2" shanks.
SOLID CARBIDE STRAIGHT BITS
Solid Carbide straight bits (pg 4) are popular simply due to price.
The cutter doesn’t stay sharp as long as the spiral versions.

PART CUTTING CUTTING SHANK OVERALL

NUMBER DIAMETER LENGTH DIAMETER LENGTH
SINGLE FLUTE
CNC ROUTER BITS
S C062 1/16" 3/16" 1/4" 1 1/2" Straight Cut - Carbide Tipped
SC01 1/16" 5/16" 1/4" 1 1/2"
CNC Tools are designed to meet the severe applications of CNC routing. These tools offer superior
SC01A 3/32" 5/16" 1/4" 1 1/2"
SC02 1/8" 3/8" 1/4" 1 1/2" performance over standard straight flute bits at the high feed rates commonly found on CNC routers.
SC03 5/32" 5/8" 1/4" 1 1/2" They also provide an economical alternative to the more expensive spiral bits. For the ultimate in CNC
SC04 3/16" 1/2" 1/4" 1 1/2" routing, choose from KLINGSPOR’s wide selection of Solid Carbide Spiral Bits listed on pages 4 and 5.
SC05 7/32" 3/4" 1/4" 2" ** Use on CNC Routers only.
SC06 1/4" 3/4" 1/4" 2"
SC07 1/4" 1" 1/4" 2 1/2" PART CUTTING CUTTING OVERALL
SC08 1/4" 1" 1/4" 3" NUMBER DIAMETER LENGTH LENGTH
SC17 5/16" 1" 5/16" 2 1/2"
1/2" SHANK • SINGLE FLUTE
DOUBLE FLUTE C1052 1/2" 1 1/4" 2 7/8"
S C33 1/8" 1/4" 1/4" 2" C1055 1/2" 2" 4 1/8"
SC09 1/8" 3/8" 1/4" 1 1/2"
SC09A 1/8" 3/8" 1/4" 2" 1/2" SHANK • DOUBLE FLUTE
C1067 1/2" 1 1/4" 2 7/8"
SC156 5/32" 3/8" 1/4" 1 1/2"
C1069 1/2" 1 1/2" 3 1/8"
SC10 5/32" 5/8" 1/4" 1 1/2"
C1072 1/2" 2" 4 1/8"
SC10A 5/32" 5/8" 1/4" 2"
SC34 3/16" 3/8" 1/4" 2" 5/8" SHANK • DOUBLE FLUTE
SC11 3/16" 1/2" 1/4" 1 1/2" C6310 5/8" 1 1/4" 3"
SC11A 3/16" 1/2" 1/4" 2" C6320 5/8" 2" 4"
SC12 3/16" 5/8" 1/4" 2"
SC13 7/32"/5.5mm 3/4" 1/4" 2"
3/4" SHANK • DOUBLE FLUTE
C7512 3/4" 1 1/4" 3"
SC35 1/4" 1/2" 1/4" 2" C7515 3/4" 1 1/2" 3 1/4"
SC14 1/4" 3/4" 1/4" 2" C7520 3/4" 2" 4"
SC15 1/4" 1" 1/4" 2 1/2" C7520F 3/4" 2" 4"
SC16 1/4" 1" 1/4" 3" C7520V 3/4" 2" 4"
SC18 5/16" 1" 5/16" 2 1/2" C7525 3/4" 2 1/2" 4 1/2"
SC19 3/8" 1" 3/8" 2 1/2" C7525F 3/4" 2 1/2" 4 1/2"
SC19A 3/8" 1 1/4" 3/8" 3" C8820V 7/8" 2" 4"
SC218 7/32"/5.5mm 3/4" 1/2" 2 3/4" C1108 1" 1 1/2" 3 1/4"
SC235 15/64"/6mm 3/4" 1/2" 2 3/4" C1109 1" 2" 4 1/4"
SC20 1/4" 3/4" 1/2" 2 3/4"
SC21 1/4" 1" 1/2" 3" F - Supplied with Carbide Flat Bottom Boring Point
SC22 5/16" 1" 1/2" 3" V - Supplied with Carbide Vee Bottom Boring Point
SC23 3/8" 1" 1/2" 3"
SC24 3/8" 1 1/4" 1/2" 3"
SC25 1/2" 1" 1/2" 3"
SC26 1/2" 1 1/4" 1/2" 3"
SC27 1/2" 1 1/2" 1/2" 3 1/2"

SOLID CARBIDE
FIBERGLASS BITS
The Solid Carbide Fiberglass Bit looks a lot like a wood rasp, and that’s pretty much what it is. Their
material removing capacity is limited relative to other kinds of bits but they are great for finishing cuts.
Since the feed rate needs to be a little slower they’re gentle on the material and are often used with
composites, PC board material, fiberglass, and other layered materials.

PART CUTTING CUTTING SHANK OVERALL

NUMBER DIAMETER LENGTH DIAMETER LENGTH
SC90 1/4" 3/4" 1/4" 2 1/2"
SC90V 1/4" 3/4" 1/4" 2 1/2"
SC91V 1/4" 1" 1/4" 3"

*Note - order SC90 for flat bottom plunge point

SC90V & SC91V are supplied with vee plunge point

ROUTER BITS 6 Call Toll Free 800-645-5555

 SOLID CARBIDE
Solid Carbide flush / bevel trim bits work well, but do not have the bearing to follow the template.
Instead, the solid end follows the template. This can create burning if a lubricant is not used. These are
common in laminate countertop applications.
The 7 degree bevel bits allow for minimal filing of the edge once routed. This is a huge benefit for the
FLUSH & 7° BEVEL TRIM end user as it saves them time, which is money.
- WITHOUT PILOT
PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH
SC30 3/8" 1/4" 1 1/2"

STANDARD FLUSH TRIM - 1/4" CUT LENGTH

PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH
SC28B 1/4" 1/4" 1 1/2"
SC28B-BLK 100 Pcs. - Bulk

HOLE & FLUSH TRIM

PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH
SC31 3/8" 1/4" 2" FLUSH TRIM - 3/8" CUT LENGTH
PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH
SC28 3/8". 1/4" 1 1/2"
SC28-BLK 100 Pcs. - Bulk

RIP & SLOTTING

PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH FLUSH TRIM - DOUBLE END
SC32 3/8" 1/4" 1 1/2" PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH
SC28A 1/4" 1/4" 2"

1/8" PILOT

FLAT BOTTOM VEINING DADO TRIM - SMALL PILOT FOR DADO

PART CUTTING CUTTING OVERALL PART CUTTING SHANK OVERALL
NUMBER DIAMETER LENGTH LENGTH NUMBER LENGTH DIAMETER LENGTH
SC28C 1/4". 1/4" 1 1/2"
1/4" SHANK - DOUBLE FLUTE SC28C-BLK 100 Pcs. - Bulk
SC062 1/16" 3/16" 1 1/2"
SC33 1/8" 1/4" 2"
SC156 5/32" 3/8" 1 1/2"
SC34 3/16" 3/8" 2"
SC35 1/4" 1/2" 2"

7° BEVEL TRIM
PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH
SC29 1/4" 1/4" 1 1/2"
SC29-BLK 100 Pcs. - Bulk

ROUND BOTTOM VEINING

PART RADIUS CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH

1/4" SHANK - DOUBLE FLUTE

SC39 1/16" 1/8" 1/4" 2" 7° BEVEL TRIM - DOUBLE END
SC40 3/32" 3/16" 3/8" 2"
SC41 1/8" 1/4" 1/2" 2" PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH
LH Rotation available by request.
SC29A 1/4" 1/4" 2"

Visit us online: www.klingspor.com 7 ROUTER BITS

 CARBIDE TIPPED STRAIGHTS

1/4" SHANK STRAIGHT BITS

PART CUTTING CUTTING OVERALL SPECIAL
LEFT HAND - STRAIGHT CUT NUMBER DIAMETER LENGTH LENGTH USE
PART CUTTING CUTTING OVERALL 1/4" SHANK • SINGLE FLUTE
NUMBER DIAMETER LENGTH LENGTH
For smaller sizes see solid carbide straight bits on page 6.
1/4" SHANK • DOUBLE FLUTE 1004 1/4" 3/4" 2 1/4"
1014LH 1/4" 1" 2 1/2" 1005 1/4" 1" 2 1/2"
1007 1/4" 1" 3 1/8"
1/2" SHANK • DOUBLE FLUTE 1007A 1/4" 1" 3 1/4" Air Router
1062LH 3/8" 1" 2 5/8"
1008 9/32" 3/4" 2 1/4"
1066LH 1/2" 1" 2 5/8"

1069LH 1/2" 1 1/2" 3 1/8"
1072LH 1/2" 2" 4 1/8" 1/4" SHANK • DOUBLE FLUTE
1085LH 3/4" 1 1/4" 3" For smaller sizes see solid carbide straight bits on page 6.
3/4" SHANK • DOUBLE FLUTE 1012 1/4" 1/2" 2"
1105LH 3/4" 2" 5" 1013 1/4" 3/4" 2 1/4" Incra™
* 1126LH 3/4" 2 1/2" 5" 1014 1/4" 1" 2 1/2"
* 1128LH 3/4" 2 1/2" 5 1/2" 1016 1/4" 1" 3"
1016-01 1/4" 1" 3 1/4" Air Router
* Recommended for "Topmaster" machines. 1018 9/32" 1" 3"
NOTE: Left Hand Spiral Bits also available, See pg. 2
1019 5/16" 1" 2 1/2" OmniJig® #43300
1020 5/16" 1" 2 3/4" Leigh #140
1020x8 5/16" 1" 2 3/4" Leigh #140-8mm shank
1021 3/8" 3/4" 2 1/4"
1022 3/8" 1" 2 1/2" Incra™
1023 3/8" 1 1/4" 2 3/4"
1023A 13/32" 1" 2 1/2"
1024 7/16" 1" 2 1/2"
1024A 31/64" 3/4" 2 1/4" Undersize Plywood Dado
3/8" SHANK STRAIGHT BITS 1025 1/2" 3/4" 2 1/4"
1026 1/2" 1" 2 1/2" OmniJig® #43318
PART CUTTING CUTTING OVERALL SPECIAL 1027 9/16" 3/4" 2 1/4"
NUMBER DIAMETER LENGTH LENGTH USE 1027A 19/32" 3/4" 2 1/4" Undersize Plywood Dado
1028 5/8" 3/4" 2 1/8"
3/8" SHANK • SINGLE FLUTE 1029 11/16" 3/4" 2 1/8"
1035 3/8" 1" 2 5/8" 1029A 23/32" 3/4" 2 1/8" Undersize Plywood Dado
1030 3/4" 3/4" 2 1/8"
1036 3/8" 1 1/4" 2 7/8"
1031 3/4" 1" 2 5/8"
3/8" SHANK • DOUBLE FLUTE 1033 1" 3/4" 2 1/8"
1039 3/8" 1" 2 5/8" 1303 1 1/4" 1/2" 2 1/8" Mortising
1040 3/8" 1 1/4" 2 7/8"
1041 3/8" 1 1/4" 3 5/8" Air Router
1043 1/2" 1" 2 1/2"
1045 7/8" 1" 2 1/2"

ROUTER BITS 8 Call Toll Free 800-645-5555

 CARBIDE TIPPED STRAIGHTS

1/2" SHANK STRAIGHT BITS STRAIGHT CUT

PART CUTTING CUTTING OVERALL SPECIAL
CABINET DADO BITS
NUMBER DIA LENGTH LENGTH USE For Undersized Plywood
1/2" SHANK • SINGLE FLUTE Straight cut cabinet dado bits are ideal for those using undersized plywood. They are also available in
1049 3/8" 1" 2 5/8" spiral geometry.
1050 3/8" 1 1/4" 2 7/8"
1051 1/2" 3/4" 2 3/8" Midwest Machine PART CUTTING PLYWOOD CUTTING OVERALL
NUMBER DIAMETER SIZE LENGTH LENGTH
1052 1/2" 1 1/4" 2 7/8"
1054 1/2" 1 1/2" 3 1/8" 1/4" SHANK • DOUBLE FLUTE
1055 1/2" 2" 4 1/8" sc SC13 7/32" 1/4"/5.5mm 3/4" 2"
1055A 1/2" 2 1/2" 4 3/8" 1024A 31/64" 1/2" 3/4" 2 1/4"
1027A 19/32" 5/8" 3/4" 2 1/4"
1/2" SHANK • DOUBLE FLUTE 1029A 23/32" 3/4" 3/4" 2 1/8"
1058 1/4" 3/4" 2 3/8" Incra™
1059 9/32" 3/4" 2 3/8" 1/2" SHANK • DOUBLE FLUTE
1060 5/16" 1" 2 5/8" sc SC218 7/32" 1/4"/5.5mm 3/4" 2 3/4"
1061 3/8" 3/4" 2 3/8" sc SC235 15/64" 15/64"/6mm 3/4" 2 3/4"
1062 3/8" 1" 2 5/8" Incra™ 1065A 31/64" 1/2" 1" 2 5/8"
1063 3/8" 1 1/4" 2 7/8" 1075A 19/32" 5/8" 3/4" 2 1/4"
1064 13/32" 3/4" 2 1/2"
1083A 23/32" 3/4" 1" 2 1/2"
1065 7/16" 1 1/4" 2 7/8"
1065L 7/16" 1 1/4" 3 1/4" Leigh #150 sc - Solid Carbide
1065A 31/64" 1" 2 5/8" Undersize Plywood Dado
1066 1/2" 1" 2 5/8"
1067 1/2" 1 1/4" 2 7/8" Leigh #160
1067F 1/2" 1 1/4" 2 7/8" Carbide Boring Point
1069 1/2" 1 1/2" 3 1/8"
1069DS 1/2" 1 1/2" 3 1/8" Down Shear
1070 1/2" 1 1/2" 4 1/8"
1071 1/2" 2" 3 1/2" TEMPLATE BITS
1072 1/2" 2" 4 1/8" Ball Bearing Guide
1073 1/2" 2 1/2" 4 3/8"
1073-01 1/2" 2 1/2" 5 1/2" Template bits have a top bearing for following a template that is on top of the work. Carbide tipped.
1073-03 1/2" 2 1/2" 5 1/2" Flat on shank Double flute.
1074 17/32" 1 1/4" 2 7/8"
1075 9/16" 1 1/4" 3" PART CUTTING CUTTING OVERALL BEARING
1075A 19/32" 3/4" 2 1/4" Undersize Plywood Dado
NUMBER DIAMETER LENGTH LENGTH NUMBER
1076 5/8" 1" 2 1/2" 1/4" SHANK
1076F 5/8" 1" 2 1/2" Carbide Boring Point * 3000A 1/2" 1/8" 1 3/4" B9
1077 5/8" 1 1/4" 3" * 3000 1/2" 1/4" 1 7/8" B9
1078 5/8" 1 1/2" 3" 3001 1/2" 1/2" 2" B9
1079 5/8" 2" 4" 3002 1/2" 3/4" 2 1/4" B9
1080 21/32" 1 1/4" 3" 3004 1/2" 1" 2 1/2" B9
1082 11/16" 1" 2 1/2" * 3006 5/8" 1/4" 1 3/4" B6
1083 11/16" 1 1/4" 3" K41 5/8" 1/2" 2 1/4" B6
1083A 23/32" 1" 2 1/2" Undersize Plywood Dado K43 5/8" 3/4" 2 1/2" B6
1302A 3/4" 5/8" 2 1/4" Mortising 3008 5/8" 1" 2 1/2" B6
1084 3/4" 1" 2 3/4" * 3010 3/4" 1/4" 1 3/4" B4
1085 3/4" 1 1/4" 3" 3012 3/4" 3/4" 2 3/8" B4
3014 3/4" 1" 2 5/8" B4
1085F 3/4" 1 1/4" 3" Carbide Boring Point
1086 3/4" 1 1/2" 3 1/4" 3/8" SHANK
1087 3/4" 2" 3 5/8" 3015 7/8" 1" 2 5/8" B12
1088 25/32" 1 1/4" 3"
1090 13/16" 1 1/4" 3" 1/2" SHANK
1091 7/8" 1 1/4" 3" 3016 1 1/8" 1" 3" B11
1092 15/16" 1 1/4" 3" 3018 1 1/8" 1 1/2" 3 1/2" B11
1093 1" 1 1/4" 3" 3019 1 1/8" 2" 4" B11
1093F 1" 1 1/4" 3" Carbide Boring Point
*** 3020 3/4" 1" 2 3/4" *** B19
1094 1" 1 1/2" 3" *** 3021 3/4" 1 1/4" 3" *** B19
1095 1" 2" 3 3/4" *** 3022 3/4" 1 1/2" 3 1/4" *** B19
1096 1 1/8" 1 1/2" 3" 3022A 7/8" 1 1/2" 3 1/2" B13
1304 1 1/4" 1/2" 2 1/8" Mortising
*** 3023 3/4" 2" 3 5/8" *** B19
1097 1 1/4" 1 1/2" 3"
* Dado Clean out bits. Use to Square the bottom of dado cuts made on a table saw.
1098 1 3/8" 1 1/4" 3"
*** KLINGSPOR recommends using bits over 3/4" diameter in 1/2" shank whenever
1099 1 1/2" 1 1/4" 3" possible due to the fragile nature of the B19 bearing.
1100 1 3/4" 1 1/4" 3"
1101 2" 1 1/4" 3"

Visit us online: www.klingspor.com 9 ROUTER BITS

 STAGGERTOOTH • MORTISE

STAGGERTOOTH BITS
Straight Flute Staggertooth Bits (straight & up/down) offer good chip deflection, but *with HMA 1/2 only
require a slower feed rate. The up/down version has an up shear on one side and a down shear on the
other making them ideal for melamine, plywood, laminates, and solid surface. SCREW TYPE HELIX MORTISE
With Downshear - Cutter Only Mortise bits are for shallow recesses like in
PART CUTTING CUTTING OVERALL
NUMBER DIAMETER LENGTH LENGTH grooving out for a door hinge. They are available in standard and a screw type helix that threads onto
an arbor.
1/4" SHANK
1200 1/4" 1 1/4" 3 1/2" PART CUTTING CUTTING OVERALL
1/2" SHANK NUMBER DIAMETER LENGTH LENGTH
Fractional Decimal
1201 3/8" 1 1/2" 3 1/8"
1202 1/2" 1 1/2" 3 1/8" 13-500 1/2" .500 5/8" 7/8"
1203 1/2" 2 1/8" 4" 13-515 33/64" .515 5/8" 7/8"
1205 1/2" 2 5/8" 5 1/2" 13-531 17/32" .531 5/8" 7/8"
13-562 9/16" .562 5/8" 7/8"
13-625 5/8" .625 5/8" 7/8"
13-640 41/64" .640 5/8" 7/8"
13-656 21/32" .656 5/8" 7/8"
13-687 11/16" .687 5/8" 7/8"
13-719 23/32" .719 5/8" 7/8"
13-750 3/4" .750 5/8" 7/8"
13-765 49/64" .765 5/8" 7/8"
13-781 25/32" .781 5/8" 7/8"
UP/DOWN STAGGERTOOTH BITS 13-812 13/16" .812 5/8" 7/8"
Opposite Shear (Compression) 13-875 7/8" .875 5/8" 7/8"
13-937 15/16" .937 5/8" 7/8"
13-1000 1" 1.000 1/2" 1/2"
PART CUTTING CUTTING OVERALL 13-1125 1 1/8" 1.125 1/2" 1/2"
NUMBER DIAMETER LENGTH LENGTH
13-1250 1 1/4" 1.250 1/2" 1/2"
* 13-1250A 1 1/4" 1.250 1/2" 1/2"
1/2" SHANK
1250 1/2" 1 1/2" 3 1/2"
* 13-1250A supplied with 5/16"-24 threads. All others supplied with 1/4"-28 threads.
1252 1/2" 2" 4"
Special Cutting Diameters Available by Special Order.
5/8" SHANK
1260 3/4" 2" 4"
3/4" SHANK
1270 3/4" 2" 4"

HELIX MORTISE ARBORS

Helix Mortise Arbors are for use with the “screw type helix mortise cutters". They are available in both
1/4" & 1/2" shank and 1/4"-28 and 5/16"-24 threads.
PART SHANK OVERALL
NUMBER DIAMETER THREAD LENGTH

MORTISE BITS HMA-1/4

* HMA-1/2
1/4"
1/2"
1/4"-28
1/4"-28
1 3/4"
1 3/4"
PART CUTTING CUTTING OVERALL ** HMA-1/4A 1/4" 5/16"-24 1 3/4"
NUMBER DIAMETER LENGTH LENGTH *** HMA-1/2A 1/2" 5/16"-24 1 3/4"
1/4" SHANK
1300 1/2" 3/4" 2 1/8" ** Fits #13-1250A only
1301 5/8" 3/4" 2 1/8"
1302 3/4" 3/4" 2 1/8"
1303 1 1/4" 1/2" 2 1/8"
1/2" SHANK
1302A 3/4" 5/8" 2 1/4"
1304 1 1/4" 1/2" 2 1/8"

If you need a square corner on your mortise, use KLINGSPOR’s Square Corner
Chisel - see page 36.

ROUTER BITS 10 Call Toll Free 800-645-5555

 ROUND NOSE • HALF ROUND
B

BOWL & TRAY BITS *with 1/2" shank only

Bowl & Tray bits are used for dishing out and making flat bottomed grooves with curved edges. It is avail- R
able with a top bearing (on two bits) for following a template. Carbide tipped. Two-wing cutter. C *with 1/2" shank only
HALF ROUND (BULL NOSE)
PART CUTTING CUTTING OVERALL Half Round bits are used to create complete rounded edge. Also known as a “Bull Nose Bit", they are
NUMBER RADIUS DIAMETER LENGTH LENGTH
typically used in a router table or with an edge guide and are available in about any radius (based on
1/4" SHANK thickness of the edge trying to round over). Carbide tipped. Two-wing cutter.
1370 1/8" 7/16" 5/16" 2 1/8" "R" "B" "C"
1372 1/4" 3/4" 5/8" 2 3/8" PART OPENING CUTTING LARGE
* 1372B 1/4" 3/4" 5/8" 2 3/8" NUMBER RADIUS OF CUTTER LENGTH DIAMETER
1/2" SHANK 1/4" SHANK
1374 1/4" 3/4" 5/8" 2 3/8"
1425 3/32" 3/16" 1/2" 3/4"
1376 1/4" 1 1/4" 1/2" 2 1/4"
1426 1/8" 1/4" 9/16" 7/8"
* 1376B 1/4" 1 1/4" 1/2" 2 1/4"
1427 3/16" 3/8" 7/8" 1"
* Supplied with Bearing on Shank for Pattern Template Routing. 1428 1/4" 1/2" 1" 1 1/8"
1/2" SHANK
1429 3/32" 3/16" 1/2" 3/4"
1430 1/8" 1/4" 9/16" 7/8"
1431 3/16" 3/8" 7/8" 1"
1432 1/4" 1/2" 1" 1 1/8"
ROUND NOSE 1432A 5/16" 5/8" 1" 1 1/4"
(CORE BOX) *with 1/2" shank only
1433
1433A
3/8"
7/16"
3/4"
7/8"
1 1/4"
1 1/2"
1 5/8"
1 7/8"
Round Nose bits make round bottomed grooves. They are very popular for fluting of moldings creating 1434 1/2" 1" 1 1/2" 1 15/16"
a trough around cutting boards and many other uses. Round nose bits are available standard and 1434A 9/16" 1 1/8" 1 1/2" 1 15/16"
some are also available with a bearing. They may be commonly known as a “Core Box Bit" as well. 1435 5/8" 1 1/4" 1 3/4" 2 3/16"
Carbide tipped. Two-wing cutter.. 1436 3/4" 1 1/2" 1 7/8" 2 7/16"
PART CUTTING CUTTING OVERALL Note- Large Diameter minus "B" opening equals small diameter.
NUMBER RADIUS DIAMETER LENGTH LENGTH /2"
1
R
1/4" SHANK
SC SC39 1/16" 1/8" 1/4" 2" 11/8"
SC SC40 3/32" 3/16" 3/8" 2"
SC SC41 1/8" 1/4" 1/2" 2"
1403 3/16" 3/8" 1/2" 2" B
A
1404 1/4" 1/2" 5/8" 2 1/4"
1405 5/16" 5/8" 3/8" 2" PLUNGE CUT HAND GRIP
1406 3/8" 3/4" 7/16" 2" Plunge Cut Hand Grip bit is used for plunging into the material and following a template (bearing
1/2" SHANK and lock collar sold separately) to create a soft edge hand grip in drawers and doors. Carbide tipped.
1407 3/16" 3/8" 1" 2 5/8" Two-wing cutter.
1408 1/4" 1/2" 1 1/4" 2 7/8"
"A" "B"
1410 5/16" 5/8" 1 1/4" 2 7/8" PART BEAD BEAD CUTTING OVERALL
1411 3/8" 3/4" 1 1/4" 2 7/8" NUMBER OPENING DEPTH LENGTH LENGTH
1412 7/16" 7/8" 1 1/4" 2 7/8"
1413 1/2" 1" 1 1/4" 2 7/8" 1/2" SHANK
1414 5/8" 1 1/4" 1 1/4" 3" 1440 7/8" 1/4" 1 3/8" 3 1/2"
1415 3/4" 1 1/2" 1 1/4" 3" Use with B11 Bearing and LC-1/2 lock collar on shank for guide template routing.
1416 7/8" 1 3/4" 1 1/4" 3"
1417 1" 2" 1 1/4" 3" C
3/4" SHANK
1420 3/8" 3/4" 2" 4"
SC - Solid Carbide
B
A
OVAL EDGE (HALF BULL NOSE)
Oval Edge is similar to the half round bit, but it doesn’t create a full radius. Instead, it creates an oval
edge. It can be set up to produce an oval cut top to bottom or a small shoulder at the top and bottom
ROUND NOSE of the work. Carbide tipped. Two-wing cutter.
With Bearing Guide The addition of a shank mounted bearing extends the use of "A" "B" "C"
our round nose bits in lettering, veining, or decorative cuts when following a template. PART BEAD BEAD CUTTING OVERALL
NUMBER OPENING DEPTH LENGTH LENGTH
PART CUTTING CUTTING BEARING
NUMBER RADIUS DIAMETER LENGTH NUMBER 1/2" SHANK
1470 7/8" 5/32" 1 1/4" 13/16"
1/4" SHANK 1474 1/2" 1/8" 1" 3/4"
1404B 1/4" 1/2" 5/8" B9 1476 3/4" 3/16" 1 1/4" 1"
1405B 5/16" 5/8" 3/8" B6 1478 1" 3/16" 1 1/4" 1"
1406B 3/8" 3/4" 7/16" B4 1480 1 1/2" 1/4" 1 3/4" 1 1/4"

Visit us online: www.klingspor.com 11 ROUTER BITS

 V GROOVE • PANEL • COVE

PANEL BITS - PILOT PLUNGE POINT

Panel Pilot Plunge bit has a drill through point that allows self-starting, and the pilot acts as a guide
for template work. This is used heavily in the RV & mobile home industry. Carbide tipped. Two-wing
cutter.
Point Length

V GROOVE PART CUTTING CUTTING

NUMBER DIAMETER LENGTH
SHANK OVERALL
DIAMETER LENGTH
V Groove bits are available in a variety of angles. They cut deep or shallow “V" grooves. These bits
are great for sign making or for adding decorative accents to furniture and plaques. Carbide tipped. SINGLE FLUTE
Two-wing cutter. 1700 1/4" 3/4" 1/4" 2 5/8"
1701 3/8" 1" 3/8" 3 3/8"
PART CUTTING POINT OVERALL 1702 1/2" 1 1/4" 1/2" 4"
NUMBER DIAMETER LENGTH ANGLE LENGTH
1702A 1/2" 1 1/4" 1/2" 3 5/8"
1/4" SHANK
SC 1500 1/4" 1/8" 90˚ 1 1/2" DOUBLE FLUTE
1501 3/8" 3/16" 90˚ 1 7/8" 1704 3/8" 1" 1/4" 3 1/4"
1502 1/2" 1/4" 90˚ 1 7/8" 1705 3/8" 1" 3/8" 3"
SC 1540 1/4" 7/32" 60˚ 1 1/2" 1706 1/2" 1 1/4" 1/2" 4"
* SC 1541 1/4" 7/32" 60˚ 2"
1550 1/2" 7/16" 60˚ 2"
1/2" SHANK
B B
1503 1/2" 1/4" 90˚ 2"
1504 3/4" 3/8" 90˚ 2 1/4"
1506 1" 1/2" 90˚ 2 1/4"
1508 1 1/2" 3/4" 90˚ 2 5/8"
1560 1/2" 7/16" 60˚ 2 1/4" A
1/2" SHANK STAGGERTOOTH PANEL BIT With Center Pilot
15-238 1-1/4" 1/2" 110˚ 2 3/16" Staggertooth Panel Bit has an up shear on the bottom and a down shear on the top. The center pilot
15-240 1-1/4" 1/4" 130˚ 2 3/16" acts as a bearing to allow the top and bottom cutters to trim flush.
15-241 1-1/4" 3/16" 150˚ 2 3/16"
1508-91Q 1 1/2" 3/4" 91˚ 2 1/2" "A" "B"
PART CUTTING CUTTING FLUTE OVERALL
SC - Solid Carbide Not for miter folding. NUMBER DIAMETER LENGTH LENGTH LENGTH
* #1541 features three flutes for improved veining
1/2" SHANK
1726 1/2" 2 3/4" 1 1/8" 4 1/4"

COVE BITS *with bearing & journal removed

Cove bits are used to create a convex radius corner. With the bearing riding along the edge the depth
Cut Length can be adjusted to create a custom look. Carbide tipped. Two-wing cutter.
POINT CUTTING ROUNDOVER PART RADIUS LARGE CUTTING BEARING
NUMBER DIAMETER LENGTH NUMBER
Decorative Trimming & Lettering Point Cutting Roundover bits are used
to make moldings, fluting, and are popular with sign makers for routing letters. It is similar to a “V" bit 1/4" SHANK
but creates a rounded profile on each side instead of a flat “V". Carbide tipped. Two-wing cutter. 1800A 3/16" 7/8" 1/2" B3
1800 1/4" 1" 1/2" B3
PART CUTTING CUTTING OVERALL 1801 3/8" 1 1/4" 1/2" B3
NUMBER RADIUS DIAMETER LENGTH LENGTH 1802 1/2" 1 1/2" 5/8" B3

1/4" SHANK 1/2" SHANK

1570 3/16" 3/8" 3/8" 2" 1803 1/4" 1" 1/2" B3
1572 1/4" 1/2" 1/2" 2" 1804 3/8" 1 1/4" 1/2" B3
1574 3/8" 3/4" 5/8" 2" 1805 1/2" 1 1/2" 5/8" B3
1806 5/8" 1 3/4" 3/4" B3
1/2" SHANK 1807 3/4" 2" 7/8" B3
1580 3/8" 3/4" 5/8" 2 1/4" 1810 1" 2 1/2" 1" B3

Point Cutting Roundovers are not guaranteed against breakage. Bearing Number: B3

ROUTER BITS 12 Call Toll Free 800-645-5555

 RABBETING
MULTI RABBET SET
Change your Rabbet
depth by changing the
bearing! Set includes all
eight bearings to make
Cutting Depth
each of the cuts shown.
Hex Wrench included.
RABBET BITS Cutting Length

Rabbet bits are used to route out the edge of a workpiece. It is used primarily for installing backs of
cabinets. It is available individually as well as in a set, both standard and deep. With the set, you simply
change the bearing to create the different depth of cuts needed from flush to 1/2". Carbide tipped.
Two-wing cutter.
PART LARGE CUTTING CUTTING BEARING
NUMBER DIAMETER LENGTH DEPTH NUMBER
1/4" SHANK
1880 7/8" 1/2" 1/4" B2
1900 1 1/4" 1/2" 3/8" B3
1951 1 3/8" 1/2" 1/2" B2
1/2" SHANK
1885 7/8" 5/8" 1/4" B2
1901 1 1/4" 1/2" 3/8" B3
1/4 5/16
1954 1 3/8" 1/2" 1/2" B2 FLUSH TRIM 1/8 3/16
1959 1 7/8" 1" 3/4" B2

Cutting Depth
3/8 7/16 1/2

SET LARGE CUTTING

NUMBER DIAMETER LENGTH DESCRIPTION

Cutting Length 1952 1 3/8" 1/2" 1/4" Shank Set

1955 1 3/8" 1/2" 1/2" Shank Set
SLOTTING & RABBETING Sets are organized and protected in 4" x 4" x 3" Box.
Slotting & Rabbeting bit performs similarly to the standard rabbeting bit. It has a thinner cutter to
allow for a groove in the middle on one piece and a rabbeted edge top and bottom on the mating DEEP MULTI RABBET SET
piece. This allows for the two pieces to be glued and mated together. There are several bearing options
to allow for quick change of the depth of cuts. Carbide tipped. Two-wing cutter. Cutting Depth

PART LARGE CUTTING CUTTING OVERALL KLINGSPOR’s largest

NUMBER DIAMETER LENGTH DEPTH LENGTH Rabbet Bit in a set with
1/4" SHANK five bearings.
1904 1 1/4" 1/8" 3/8" 2" Makes those extra deep
*1908 1 1/2" 5/32" 1/2" 1 3/4" Rabbet cuts as shown.
1912 1 1/4" 1/4" 3/8" 2" Hex Wrench included.
1916 1 1/4" 3/8" 3/8" 2"
1920 1 1/2" 1/2" 1/2" 2"
1/2" SHANK
1906 1 1/4" 1/8" 3/8" 2"
*1910 1 1/2" 5/32" 1/2" 2"
1914 1 1/4" 1/4" 3/8" 2"
1918 1 1/4" 3/8" 3/8" 2 1/8"
1922 1 1/2" 1/2" 1/2" 2 1/4"
1924 1 1/4" 3/4" 3/8" 2 1/2"
B3 Bearing supplied.
* Proper Size for Biscuit Joining 1/2 9/16 5/8
BB501 - Bearing Kit with Wrench (see pg. 35). Increase the versatility of your Rabbeting
Bits by simply changing the bearing size to vary your cutting depth. This set allows 1/4",
5/16", 3/8", & 7/16" cutting depth on all 1 1/4" bits or 3/8", 7/16", 1/2", & 9/16" cutting
depth on all 1 1/2"bits.

BISCUIT JOINING KIT 11/16 3/4

This kit contains our 5/32" Rabbeting Bit with 1/2" B3 bearing for cutting slots to fit #20 Biscuits. Also
includes alternate bearings B14 and B15 to cut slots for #0 and #10 Biscuits. Hex Wrench included.
SET LARGE CUTTING
PART NUMBER DESCRIPTION NUMBER DIAMETER LENGTH DESCRIPTION

1940 1/4" shank kit 1960 1 7/8" 1" 1/2" Shank Set
1945 1/2" shank kit Sets are organized and protected in 4" x 4" x 3" Box.

Visit us online: www.klingspor.com 13 ROUTER BITS

 ROUNDOVER
Roundover bits are some of the most common bits found in shops. They are used for things from eas-
ing the edge of the work to more elaborate moldings applications. They can also be used for creating
a complete bullnose in two passes, or change the bearing and go from a roundover to a beading bit.
VARY BEAD SETS For
They are available with or without a bearing, depending on the application and bit. Carbide tipped. extra deep beading
Two-wing cutter.
GREAT FOR
TIGHT
PLACES

R-OVER 1/16 BEAD 1/8 BEAD 3/16 BEAD

MULTI BEADING SETS

ROUNDOVER BITS Small Pilot For extra deep beading Roundover and More! Conventional Beading only cuts
a shallow 1/16" bead. Expand your capabilities with these versatile sets. Deeper beads create a more
Extra Small Brass Pilot (5/32" dia.) allows these bits to roundover edges on finely detailed workpieces with
pronounced edge on larger pieces. Includes all four bearings and Hex Key Wrench.
intricate contours, tight corners, and narrow openings. These bits give professional results without all the
tedious hand sanding. Carbide cutting edges far outlast comparable high speed steel bits. PART LARGE CUTTING OVERALL
PART LARGE CUTTING OVERALL NUMBER RADIUS DIAMETER LENGTH LENGTH
NUMBER RADIUS DIAMETER LENGTH LENGTH
1/2" SHANK
1/4" SHANK 2040B 1/4" 1 1/4" 1/2" 2 3/8"
1978 1/16" 3/8" 7/16" 2" 2042B 3/8" 1 1/2" 5/8" 2 1/2"
1980 1/8" 3/8" 7/16" 2" 2044B 1/2" 1 3/4" 3/4" 2 5/8"
1982 1/4" 5/8" 1/2" 2 1/8"
1984 3/8" 7/8" 5/8" 2 1/4"

B A

BEADING ROUNDOVER

R
ROUNDOVER & BEADING
Ball Bearing Guide
ROUND- PLUNGE ROUNDOVER With Plunge Point
OVER BEADING
PART PART RADIUS LARGE CUTTING "R" "A" "B" "C"
NUMBER NUMBER DIAMETER LENGTH PART RADIUS LARGE SMALL PATTERN OVERALL
NUMBER DIAMETER DIAMETER LENGTH LENGTH
1/4" SHANK
2000A 2100A 1/16" 5/8" 1/2" 1/4" SHANK
2000B 3/32" 11/16" 1/2" 2050 1/8" 3/8" 1/8" 1/4" 1 3/4"
2000C 2100C 1/8" 3/4" 1/2" 2051 3/16" 5/8" 1/4" 1/8" 1 3/4"
2000D 2100D 5/32" 13/16" 1/2" 2052 1/4" 3/4" 1/4" 3/8" 1 7/8"
2000 2100 3/16" 7/8" 1/2"
2001 2101 1/4" 1" 1/2" 1/2" SHANK
2002 2102 5/16" 1 1/8" 1/2" 2055 1/4" 3/4" 1/4" 1/4" 2"
2003 2103 3/8" 1 1/4" 5/8" 2056 1/4" 3/4" 1/4" 3/8" 2"
2004 2104 1/2" 1 1/2" 3/4" 2057 3/8" 1" 1/4" 5/16" 2 1/8"
1/2" SHANK 2058 3/8" 1" 1/4" 9/16" 2 1/4"
2005C 2105C 1/8" 3/4" 1/2" 2060 1/2" 1 3/8" 3/8" 3/4" 2 1/2"
2005 2105 3/16" 7/8" 1/2" 2062 9/16" 1 5/8" 1/2" 1" 2 3/4"
2006 2106 1/4" 1" 1/2" 2064 5/8" 1 3/4" 1/2" 1 5/16" 3"
2007 2107 5/16" 1 1/8" 1/2" 2066 3/4" 2" 1/2" 1 5/16" 3"
2008 2108 3/8" 1 1/4" 5/8"
2008A 7/16" 1 3/8" 5/8" ROUNDOVER & EDGE TRIM (Long Nose)
2009 2109 1/2" 1 1/2" 3/4" "R" "A" "B" "C"
2009A 5/8" 1 3/4" 1" PART RADIUS LARGE SMALL PATTERN OVERALL
2009B 9/16" 1 5/8" 3/4" NUMBER DIAMETER DIAMETER LENGTH LENGTH
2010 2110 3/4" 2" 1"
2011 7/8" 2 1/4" 1 1/8" 1/2" SHANK
2012 1" 2 1/2" 1 5/16" * 2068 3/16" 1" 1/2" 13/16" 2 5/8"
2013 1 1/8" 3" 1 1/2" ** 2070 3/16" 1" 1/2" 1 5/16 " 3 1/8"
2014 1 1/4" 3 1/4" 1 3/4" * 2072 1/4" 1 1/8" 1/2" 13/16" 2 5/8"
2015 1 3/8" 3 1/2" 1 3/4" ** 2074 1/4" 1 1/8" 1/2" 1 5/16 " 3 1/4"
2016 1 1/2" 3 3/4" 1 7/8" * 2076 3/8" 1 3/8" 1/2" 13/16" 2 3/4"
Bearing: Use B3 for Rounding Over ** 2078 3/8" 1 3/8" 1/2" 1 5/16 " 3 1/4"
Use B2 for Beading * Edge Trim for 3/4" stock
Use B4 for 2013 thru 2016 ** Edge Trim for 1 1/4" stock

ROUTER BITS 14 Call Toll Free 800-645-5555

 ROMAN OGEE • CHAMFER
A
BEAD
B

FLUSH

1 5/8" MAX

C
DOUBLE ROUND OVER 45˚ CHAMFER
with Adjustable Cutting Length Double Roundover bit is as the name with Adjustable Cutting Length 45° Chamfer & Edge Bevel bits produce
implies. It is and adjustable bit that creates a rounded edge on the top and bottom of the work at a 45° angle on the material and are used as a decorative edge or miter joint to produce uniformly crisp
the same time. The bearing is changeable, to allow the bit to go from a roundover to a beading angles. Carbide tipped. Two-wing cutter.
application. Carbide tipped. Two-wing cutter.
"A" "B" "C"
PART DEGREE CUTTING CUTTING OVERALL
NUMBER OF ANGLE LENGTH HEIGHT LENGTH
PART LARGE OVERALL
NUMBER RADIUS DIAMETER LENGTH
1/4" SHANK
1/2" SHANK 2292 45° 7/16" 5/16" 1 7/8"
2160 1/8" 1 1/8" 3 3/4" 2302 45° 5/8" 7/16" 2"
2162 3/16" 1 1/4" 3 3/4"
2164 1/4" 1 3/8" 3 3/4" 1/2" SHANK
2305 45° 5/8" 7/16" 2 1/4"
Assemblies Sold with B5 Bearing for flush round over 2306 45° 1 1/16" 3/4" 2 1/2"
Use B20 Bearing for 1/16" Bead • Use B27 Bearing for 1/8" Bead 2310 45° 1 1/2" 1 1/16" 3"
Replacement Cutter Heads: Add RH to Part Number for cutter next to shank,
Add LH to Part Number for end cutter. Bearing Number: B3 (Use B2 on #2292)
Example: 2160LH * 2292 has 1" large diameter for use in trim routers.

25° BEVEL

EDGE BEVEL
Edge Bevel bits are similar to the chamfer bits, but produce 60°, 30°, 25°, 22-1/2°, 15°, or 7° angles
on the material and are used as a decorative edge or miter joint to produce uniformly crisp angles.
Carbide tipped. Two-wing cutter.
ROMAN OGEE
PART
"A"
DEGREE
"B"
CUTTING
"C"
CUTTING OVERALL
Roman Ogee bits has a convex curve at the bearing and a concave curve at the top. It is a decorative NUMBER OF ANGLE LENGTH HEIGHT LENGTH
profile that jazzes up any wood edge. Carbide tipped. Two-wing cutter.
1/4" SHANK
PART RADIUS LARGE CUTTING OVERALL * 2298 7° 3/8" 1/2" 2 1/8"
NUMBER DIAMETER LENGTH LENGTH 2300 15° 1/2" 1/2" 2"
* 2300A 15° 1/4" 1/4" 2"
1/4" SHANK 2301 25° 9/16" 1/2" 2"
2200 5/32" 1 1/8" 9/16" 2" 1 2308 30° 7/8" 3/4" 2 3/4"
2201 1/4" 1 1/2" 11/16" 2 1/4" 1/2" SHANK
1/2" SHANK 3 2325 15° 1" 15/16" 2 3/4"
2202 5/32" 1 1/8" 9/16" 2 1/4" 2 2307 22 1/2° 15/16" 7/8" 2 3/4"
2203 1/4" 1 1/2" 11/16" 2 3/8" 1 2309 30° 7/8" 3/4" 2 3/4"
2210 3/8" 2" 1" 2 3/4" 2318 60° 9/16" 1/2" 2 1/2"

Bearing Number: B3 Bearing Number: B3

* Used on Laminate Trim
1 Used for six sided boxes
2 Used for eight sided boxes
3 Used for twelve sided boxes

PART # 2200/2202
PART # 2201/2203
PART # 2210
15° BEVEL 22 1/2° BEVEL 30° BEVEL

Visit us online: www.klingspor.com 15 ROUTER BITS

 FLUSH TRIM
• Flush Trim bits are designed to be used to trim flush laminate work or template work. The bearing
follows the template and the cutter trims the workpiece. These bits have the bearing on the bottom
end (away from the shank) of the bit. Carbide tipped unless specified otherwise.
• Two flute flush trim bits provide a good general purpose option that will give both quick cuts and nice
finishes.
• Three flute bits offer an extremely smooth finish with three cutters doing the work.
• Flush Trim downshear bits will leave the top of the work surface a little cleaner due to the slight angle
cutting action (shear).
OVERHANG TRIM BIT
• Flush Trim downshear two flute version offers two flutes for an even better finish cut with a down PART OVERHANG CUTTING CUTTING BEARING
shear action. NUMBER DIAMETER LENGTH NUMBER
• Flush Trim V-Groove bits are ideal for flushing the workpiece to a template and simultaneously cutting 1/4" SHANK
a subtle “V" shape groove where two pieces butt together. This aids in hiding the seam and adds a 2468 1/16" 3/8" 1/2" B3
decorative accent. 2470 1/8" 3/8" 1/2" B7
• Overhang Trim Bits are similar to a conventional flush trim bit, but the bearing is oversized providing
a 1/16" or 1/8" overhang between the edge of the cutting surface and template. Carbide tipped.
Double flute.
• Combination Flush Trim bits allow the template to be placed on top of or below the workpiece. This is
a combination straight router bit with properly sized ball bearing guides on both the end of the cutter
and the shank. This is ideal for heavy duty flush trimming operations such as laminating tables and
counter tops. It also works well for table based pattern routing as well. Carbide tipped. Double flute. FLUSH TRIM - THREE FLUTE
PART CUTTING CUTTING OVERALL BEARING
NUMBER DIAMETER LENGTH LENGTH NUMBER
1/4" SHANK
2500 1/2" 1" 2 5/8" B3
FLUSH TRIM-TWO FLUTE 2501 1/2" 1/2" 2 1/8" B3

PART CUTTING CUTTING OVERALL BEARING 1/2" SHANK

NUMBER DIAMETER LENGTH LENGTH NUMBER 2502 1/2" 1" 3 1/4" B3
2503 1/2" 1/2" 2 3/4" B3
1/4" SHANK 2504 1/2" 1 1/2" 3 5/8" B3
2400 3/8" 1" 2 5/8" B1 2505 1/2" 2" 4" B3
2401 3/8" 1/2" 2 1/8" B1
2402 1/2" 1" 2 5/8" B3 1/2" SHANK - DOUBLE BEARING
2403 1/2" 1/2" 2 1/8" B3 2554 1/2" 1 1/2" 3 7/8" Two B3
1/2" SHANK 2555 1/2" 2" 4 1/4" Two B3
2404A 3/8" 1" 3 1/8" B1
2405 1/2" 1" 3 1/4" B3
2406 1/2" 1/2" 2 3/4" B3
2407 1/2" 1 1/2" 3 5/8" B3
2408 1/2" 2" 4" B3
2410 3/4" 1 1/4" 3 1/4" B4 DOWNSHEAR FLUSH TRIM
2415 7/8" 1 1/2" 3 1/2" B21 Two Flute
1/2" SHANK - DOUBLE BEARING
2457 1/2" 1 1/2" 3 7/8" Two B3 PART CUTTING CUTTING OVERALL BEARING
2458 1/2" 2" 4 1/4" Two B3 NUMBER DIAMETER LENGTH LENGTH NUMBER
1/4" SHANK
2602 1/2" 1" 2 5/8" B3
REPLACEABLE HEAD 2560 3/4" 5/8" 2 1/8" B4
FLUSH TRIM 1/2" SHANK
2605 1/2" 1" 3 1/4" B3
WM150 1/2"CD x 1/2"CL x 1/4"SH 2570 3/4" 1" 3" B4
Replacement Head Kit 2575 3/4" 1 1/2" 3 1/2" B4
WM151 10˚ Bevel Replacement Head Kit 2580 3/4" 2" 4" B4
WM156 3 Pack Flush Trim Head/WM150
WM157 3 Pack 10˚ Bevel Head/WM151

1/16" COMBINATION FLUSH TRIM

with Top and Bottom Bearings
PART CUTTING CUTTING OVERALL BEARING
FLUSH TRIM V-GROOVE NUMBER DIAMETER LENGTH LENGTH NUMBER

Part Cutting Cutting Shank Overall Bearing

1/4" SHANK
Number Diameter Length Diameter Length Number 2702 1/2" 1" 2 5/8" B3 & B9
1/2" SHANK
2425 1/2" 1" 1/4" 2 5/8" B3 2715 7/8" 1 1/2" 3 1/2" B13 & B21
2426 1/2" 1" 1/2" 3 1/4" B3
Try our solid carbide flush trim spiral bits on page 4.

ROUTER BITS 16 Call Toll Free 800-645-5555

 LAMINATE TRIM

LAMINATE TRIM BITS TRIM-N-FILE

This is the ideal router bit for all plastic laminate work. The “Trim-N-File" router bit does multiple
Two Flute - Ball Bearing Laminate Trim bits are flush trim bits, but designed for operations at once. 1) It will trim the laminate overhang flush to the edge with a slight bevel, while 2)
thinner stock like laminates and veneers. They offer a flush, 7°, 15°, and 25° angle. The bevel bits are simultaneously creating a slight radius along the top edge. 3) All this is accomplished by following the
ideal for trimming the laminate flush while also easing the top edge for faster filing. Carbide tipped. heavy duty ball bearing, which slightly protrudes past the cutter to make it all work. By simply adjusting
Double flute. the depth of cut on the router to best match the laminate thickness, a perfectly flush edge is achieved
PART BEVEL LARGE CUT BEARING and the top edge is smooth. This means that the operator won’t have to come back and file the edge
NUMBER DEGREE DIAMETER LENGTH NUMBER flush and top rounded like with traditional flush trim bits, so he is saving both time and money.
1/4" SHANK PART BEVEL LARGE CUT
2401 Flush 3/8" 1/2" B1 NUMBER RADIUS DEGREE DIAMETER LENGTH BEARING
2298 7° 9/16" 7/16" B3
2300A 15° 5/8" 1/4" B3 1/4" SHANK
2301 25° 1" 9/16" B3 2630 1/16" 2° 1 1/16" 5/16" B3
* 2631 1/16" 2° 1 1/16" 5/16" B3SQ
* Square bearing

STANDARD FLUSH TRIM SOLID CARBIDE Standard

Flush Trim bits are an economical solid carbide flush trim that does not use a bearing, but instead has a LAMINATE TRIMMERS
smooth portion milled into the solid carbide, which rides along the edge being trimmed to. They offer
extended life and minimal vibration.
Here’s a Square Deal! A quality KLINGSPOR Trim Bit with the exclusive Euro Square Bearing.
How does it work? The square bearing stops spinning as soon as it touches the workpiece.
PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH Then the side of the square simply slides along the workpiece edge. Compare this to a regular
SC28B 1/4" 1/4" 1 1/2"
bearing that rolls along the edge - building up more glue and residue with every revolu­tion.
Plus, the square is made fron non-stick Teflon®, so it wipes clean easily and it won’t mark your
workpiece. If you cut laminates, you need to try this bit.
Square Bearing Laminate Trimmer bits offer a unique solution to the problem of glue
build up during the laminate flush trimming process. Between the square bearing and the
cutter is a wider than normal trough (gap), which allows the excess glue to be evacuated
much easier than a traditional flush trim. Carbide tipped. Double flute.
7° BEVEL TRIM SOLID CARBIDE
7° Bevel Trim bits are identical to the standard flush bits, but offer a 7° bevel, which slightly eases the
top edge of laminate to reduce filing.
PART CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH
PART # B3SQ
SC29 1/4" 1/4" 1 1/2"
PART # 2640
See our complete line of solid carbide trimmers on pages 6 & 7..

PART # B8SQ
PART # 2660

COMBINATION FLUSH
OR BEVEL LAMINATE TRIM PART CUTTING
NUMBER DIAMETER
CUTTING OVERAL BEARING
LENGTH LENGTH NUMBER
Combination Flush or Bevel Laminate Trim bits are made of solid carbide and will cut, trim, and create
a bevel all in one bit. Simply change the depth of cut to go from a 22-1/2" bevel to a flush cut. This bit
1/4" SHANK
must be used with either an edge guide or fence. 2640 1/2" 1/4" 1 5/8" B3SQ
PART CUTTING DEGREE CUTTING OVERALL 2650 3/4" 5/8" 2 1/4" B8SQ
NUMBER DIAMETER OF ANGLE LENGTH LENGTH
1/2" SHANK
2660 3/4" 5/8" 2 1/4" B8SQ
1/4" SHANK
2800 7/16" 22 1/2" 1/2" 1 1/8" These bits are designed with a slight taper on the cutting diameter. This
2801 7/16" 22 1/2" 1/2" 1 7/8" allows up or down adjustment to achieve an exact blend - even after
resharpening.

Visit us online: www.klingspor.com 17 ROUTER BITS

 SOLID SURFACE BITS

ROUND OVER
With Non-Marring Bearing Round Over with non-marring bearing is ideal for
creating a perfect radius on the top of a solid surface edge. It is supplied with a special non-marring
nylon sleeve bearing to eliminate burn marks along the edge. Carbide tipped. Two-wing cutter.
ROUNDING OVER UNDERMOUNT
PART MATERIAL RADIUS OVERALL BEARING Rounding Over Undermount bits with non-marring bearing is ideal for creating a perfect radius and
NUMBER THICKNESS LENGTH NUMBER precise angle (depending on undermount sink manufacturer specifications) on the top of a solid
1/2" SHANK surface edge. It is supplied with a special non-marring nylon sleeve bearing to eliminate burn marks
2006N 1/2" 1/4" 2 1/4" B3S along the edge and sink. Carbide tipped. Two-wing cutter.
2009N 1" 1/2" 2 1/2" B3S
2010N 1 1/2" 3/4" 2 3/4" B3S PART MATERIAL RADIUS OVERALL BEARING
NUMBER THICKNESS LENGTH NUMBER
Supplied With Non-Marring Nylon Sleeved Bearing (Part #B3S).
1/2" SHANK
2929 1/2" 18° 3" BB300
2930 3/4" 18° 3 1/4" BB300
2910 1/2" 10° 3" BB300
2915 1/2" 15° 3" BB315
2918 1/2" 18° 3" BB318

ROUNDING UNDER
Rounding Under bits with non-marring bearing is ideal for creating a perfect radius on the bottom of
a solid surface edge. It is supplied with a special non-marring nylon sleeve bearing to eliminate burn
marks along the edge. Carbide tipped. Two-wing cutter.

PART MATERIAL RADIUS OVERALL BEARING

NUMBER THICKNESS LENGTH NUMBER
1/2" SHANK
2030 1/2" 1/4" 2 3/4" B5
2034 1" 1/2" 3" B5
2036 1 1/2" 3/4" 3 3/8" B5

OVERHANG BOWL TRIM

Overhang Bowl Trim bits with non-marring bearing is ideal for creating a perfect bevel angle for
undermount sinks that require a bevel on the edge of a solid surface edge mating to the sink. It is
supplied with a special non-marring nylon sleeve bearing to eliminate burn marks along the edge and
BEVEL UNDERMOUNT BOWL sink. Carbide tipped. Two-wing cutter.
Bevel Undermount Bowl bits with non-marring bearing is ideal for creating a perfect bevel angle for
PART MATERIAL OVERALL BEARING
undermount sinks that require a bevel on the edge of a solid surface edge mating to the sink. It is
NUMBER THICKNESS DIAMETER LENGTH NUMBER
supplied with a special non-marring nylon sleeve bearing to eliminate burn marks along the edge and
sink. Carbide tipped. Two-wing cutter.
1/2" SHANK
PART MATERIAL RADIUS OVERALL BEARING 2945 1/2-3/4" 3/4" 2 7/8" BB300
NUMBER THICKNESS LENGTH NUMBER
1/2" SHANK
2944 1/2-3/4" 12° 3" BB300
2944-13 1/2-3/4" 13° 3" BB300

ROUTER BITS 18 Call Toll Free 800-645-5555

 TEMPLATE •T-SLOT

TEMPLATE BITS KEYHOLE BITS

Keyhole bits are used to create a small keyhole slot on the back of picture frames, plaques, signs, etc.
Ball Bearing Guide Template Bits with ball bearing guide are similar to a flush trim Simply plunge the bit and make a groove in the proper direction to allow for a screw or nail to hold the
in that they will trim the workpiece flush, but the bearing is on the top (near the shank) of the cutter workpiece on the wall. Carbide tipped.
instead of the bottom. KLINGSPOR template bits use replaceable bearings and lock collars. Carbide
PART LARGE SMALL CUTTING OVERALL
tipped. Two-wing cutter. NUMBER DIAMETER DIAMETER LENGTH LENGTH
PART CUTTING CUTTING OVERALL BEARING 1/4" SHANK
NUMBER DIAMETER LENGTH LENGTH NUMBER 3050 3/8" 3/16" 7/16" 1 1/2"
1/4" SHANK 3052 1/2" 5/16" 7/16" 1 1/2"
* 3000A 1/2" 1/8" 1 3/4" B9 1/2" SHANK
* 3000 1/2" 1/4" 1 7/8" B9 3051 3/8" 3/16" 7/16" 2 1/8"
3001 1/2" 1/2" 2" B9 3053 1/2" 5/16" 7/16" 2 1/8"
3002 1/2" 3/4" 2 1/4" B9
3004 1/2" 1" 2 1/2" B9
* 3006 5/8" 1/4" 1 3/4" B6
K41 5/8" 1/2" 2 1/4" B6
K43 5/8" 3/4" 2 1/2" B6
3008 5/8" 1" 2 1/2" B6
* 3010 3/4" 1/4" 1 3/4" B4
3012 3/4" 3/4" 2 3/8" B4
3014 3/4" 1" 2 5/8" B4
3/8" SHANK
3015 7/8" 1" 2 5/8" B12
A
1/2" SHANK B
3016 1 1/8" 1" 3" B11
3018 1 1/8" 1 1/2" 3 1/2" B11
3019 1 1/8" 2" 4" B11
*** 3020 3/4" 1" 2 3/4" *** B19 PART # 3070 PART # 3075
*** 3021 3/4" 1 1/4" 3" *** B19
*** 3022 3/4" 1 1/2" 3 1/4" *** B19 T-SLOT CUTTER
3022A 7/8" 1 1/2" 3 1/2" B13 T-Slot Cutter “Slatwall" bits create a T-slot in wood for making jigs and fixtures in the shop.
*** 3023 3/4" 2" 3 5/8" *** B19 This allows a bolt to slide the length of the slot for easy adjustment of the jig. Carbide tipped.
* Dado Clean out bits. Use to Square the bottom of dado cuts made on a table saw. PART LARGE SMALL "A" "B" OVERALL
*** KLINGSPOR recommends using bits over 3/4" diameter in 1/2" shank whenever NUMBER DIAMETER DIAMETER LENGTH LENGTH LENGTH
possible due to the fragile nature of the B19 bearing. 1/2" SHANK
3070 1 1/16" 3/8" 5/16" 1/2" 2 3/8"
3075 1 3/16" 3/8" 1/4" 3/8" 2 3/8"

TEMPLATE BITS
With Oversize Bearings Template bits with over size bearings are similar to a
template bit in that they have a bearing on the top of the cutter but instead of trimming flush, they
offset the cut. These are made to replace bits and work with specific router jigs. KLINGSPOR template
SLOT & UNDERCUT BITS
Used to cut all types of slots and grooves. Also used to undercut decorative patterns or large letters
bits use replaceable bearings and lock collars. Carbide tipped. Two-wing cutter. to give them a bold appearance. This can even be used by hardwood flooring contactors to replace
PART CUTTING CUTTING OVERALL BEARING BEARING boards in existing floors. They have a replaceable bearing and collar. Carbide tipped.
NUMBER DIAMETER LENGTH LENGTH DIAMETER NUMBER PART LARGE "A" "B" OVERALL
1/4" SHANK NUMBER DIAMETER LENGTH DEPTH LENGTH
1 3025 5/16" 3/4" 2 3/4" 1/2" B9 1/4" SHANK
2 3027 1/2" 1/4" 1 7/8" 5/8" B6 3094 3/4" 1/8" 1/4" 1 7/8"
3 3028 1/2" 1/4" 1 7/8" 3/4" B4 *3094B 3/4" 1/8" 1/8" 1 7/8"
1,4 3032 9/16" 3/4" 2 1/4" 5/8" B6 3098 1" 1/4" 3/8" 2"
* 3098B 1" 1/4" 1/4" 2"
1 For Porter-Cable Mortenª, Mortise & Tenon Jig, and Omnijig¨ templates 3110 1 1/2" 1/4" 5/8" 2"
2 Porter-Cable Hinge Butt Mortise Bit * 3110B 1 1/2" 1/4" 1/2" 2"
3 For Hinge-Mateª II Template
4 Keller Box Joint Bit
* B denotes Bearing (B9) guide on shank.

Visit us online: www.klingspor.com 19 ROUTER BITS

 EDGE PROFILES
#3192
#3190

PART #3160/3164 PART #3162/3166

#3194 #3196

FULL BEAD
Full Bead bits offer an ideal way to accent different projects, from adding beads to furniture legs, rail-
CLASSICAL COVE ings, moldings or even post beams. KLINGSPOR’s full bead router bits also offer two separate bearings
Classical Cove bits create a decorative step & cove design along the edge of a workpiece. Carbide tipped. which make it very easy to use on template work. Carbide tipped. Two-wing cutter.
Two-wing cutter. PART LARGE CUTTING OVERALL
PART LARGE CUTTING OVERALL NUMBER RADIUS DIAMETER LENGTH LENGTH
NUMBER RADIUS DIAMETER LENGTH LENGTH 1/4" SHANK
1/4" SHANK 3190 1/8" 7/8" 5/16" 2 1/8"
3160 5/32" 1 1/4" 1/2" 2" 3192 3/16" 1" 1/2" 2 3/8"
3162 1/4" 1 3/8" 3/4" 2 1/4" 3194 1/4" 1 1/8" 5/8" 2 1/2"
3196 3/8" 1 3/8" 7/8" 2 3/4"
1/2" SHANK Bearing Number: One B6 & One B7
3164 5/32" 1 1/4" 1/2" 2 1/4"
3166 1/4" 1 3/8" 3/4" 2 1/2"
Bearing Number: B3

MULTI-BEADING
Multi-Beading bits are great for making multiple beads in one pass in moldings, furniture parts,
columns, etc. Carbide tipped. Two-wing cutter.
WAVY EDGE PART LARGE CUTTING OVERALL
Wavy Edge bits create a decorative step, wavy convex & concave edge design on the workpiece. NUMBER RADIUS DIAMETER LENGTH LENGTH
Carbide tipped. Two-wing cutter.
1/4" SHANK
PART LARGE CUTTING OVERALL 3200 1/8" 7/8" 1" 2 1/2"
NUMBER RADIUS DIAMETER LENGTH LENGTH
1/2" SHANK
1/4" SHANK 3202 1/8" 7/8" 1" 2 3/4"
3170 1/8" 1 1/4" 3/4" 2 1/4" Bearing Number: B3
1/2" SHANK
3172 1/8" 1 1/4" 3/4" 2 1/2"
Bearing Number: B3

PART #3180/3181 PART #3182/3183

RADIUS FLUTE CUTTER

Radius Flute Cutter bits are perfect for making flutes to furniture, cabinetry, columns, moldings, and DOUBLE ROUND PART #3205/3207 PART #3206/3208

more. The double bearing keeps the bit flat to the work for a precise cut. Carbide tipped. Two-wing Double Round bits create a decorative double round over along the edge of the workpiece. This
cutter. produces a nice door edge, molding, furniture profile and more. Carbide tipped two-wing cutter.
PART LARGE CUTTING OVERALL PART LARGE CUTTING OVERALL
NUMBER RADIUS DIAMETER LENGTH LENGTH NUMBER RADIUS DIAMETER LENGTH LENGTH

1/4" SHANK 1/4" SHANK

3180 1/8" 1 1/8" 1/4" 2 5/8" 3205 5/32" 1 1/8" 1/2" 2"
3182 3/16" 1 1/4" 3/8" 3 1/8" 3206 7/32" 1 3/8" 5/8" 2 1/4"

1/2" SHANK 1/2" SHANK

3181 1/8" 1 1/8" 1/4" 2 3/4" 3207 5/32" 1 1/8" 1/2" 2 1/4"
3183 3/16" 1 1/4" 3/8" 3 1/8" 3208 7/32" 1 3/8" 5/8" 2 1/2"
Bearing Number: Two B5 Bearing Number: B3

ROUTER BITS 20 Call Toll Free 800-645-5555

 EDGE PROFILES
3209 & 3211

3230 & 3232 3234 & 3236

3210 & 3212 CLASSICAL

PATTERN
Classical Pattern bits form a step down from the top, which transitions into a bead and step out. Then
the cutter produces a cove at the bottom of the cut. This is a popular bit used to mill moldings. Carbide
COVE & BEAD tipped two-wing cutter.
Cove & Bead bits as the name implies, creates a decorative cove at the top, small step, then a bead
(convex shape) at the bottom. Carbide tipped two-wing cutter PART LARGE CUTTING OVERALL
NUMBER RADIUS DIAMETER LENGTH LENGTH
PART LARGE CUTTING OVERALL
NUMBER RADIUS DIAMETER LENGTH LENGTH 1/4" SHANK
3230 5/32" 1 1/4" 1/2" 2 1/8"
1/4" SHANK 3234 3/16" 1 1/2" 5/8" 2 1/4"
3209 5/32" 1 1/8" 1/2" 2"
3210 1/4" 1 5/16" 5/8" 2 1/8" 1/2" SHANK
3232 5/32" 1 1/4" 1/2" 2 3/8"
1/2" SHANK 3236 3/16" 1 1/2" 5/8" 2 1/2"
3211 5/32" 1 1/8" 1/2" 2 1/4"
3212 1/4" 1 5/16" 5/8" 2 3/8" Bearing Number: B3
3282 3/8" 2" 1 3/16" 2 7/8"
Bearing Number: B3 3244 & 3246 3252 & 3254

3214 & 3216

A

B
EDGE BEADING
Edge Beading bits offers three types of cuts using the same bit, depending upon the set up. You can
create an edge, or corner bead with or without a fillet (step) at the top, or a full corner bead by making
OGEE FILLET one pass with the bearing along the edge and another pass with the bearing along the top. Carbide
Ogee Fillet bits create an attractive small step (fillet) at the top then an ogee (convex then concave) at
tipped Two-wing cutter.
the bottom. Carbide tipped two-wing cutter.
"A" "B"
PART LARGE CUTTING OVERALL PART LARGE BEAD CUTTING OVERALL
NUMBER RADIUS DIAMETER LENGTH LENGTH NUMBER DIAMETER DIAMETER LENGTH LENGTH
1/4" SHANK 1/4" SHANK
3214 3/16" 1 3/8" 5/8" 2 1/8" 3240 7/8" 1/8" 9/16" 2"
3244 7/8" 1/4" 9/16" 2"
1/2" SHANK 3248 1" 5/16" 5/8" 2 1/4"
3216 3/16" 1 3/8" 5/8" 2 1/2" 3252 1 1/16" 3/8" 3/4" 2 1/4"
3218 1/4" 1 5/8" 3/4" 2 5/8" 3256 1 1/16" 1/2" 3/4" 2 1/4"
Bearing Number: B3 1/2" SHANK
3242 7/8" 1/8" 9/16" 2 1/4"
3246 7/8" 1/4" 9/16" 2 1/4"
3250 1" 5/16" 5/8" 2 1/4"
3254 1 1/16" 3/8" 3/4" 2 1/2"
3258 1 1/16" 1/2" 3/4" 2 1/2"
3224 & 3226 3260 1 3/8" 5/8" 1" 2 5/8"
3228 3262 1 1/2" 3/4" 1 1/8" 3"
Bearing Number: B3
R1
*with 1/2" shank only R2

OGEE
Ogee bits produce a simple cove at the top and a convex (bead) at the bottom of FRENCH
the workpiece. Carbide tipped two-wing cutter.
TRADITIONAL 3270 & 3272

PART LARGE CUTTING OVERALL French Traditional bits produces a simple accent profile that starts with a small concave radius at the
NUMBER RADIUS DIAMETER LENGTH LENGTH top then is steps down to a larger bead at the bottom. It is a classic French Traditional profile for table
tops, drawer fronts, panel edges, moldings, and trim. Carbide tipped Two-wing cutter.
1/4" SHANK
3220 5/32" 1 1/8" 1/2" 2" PART "R1" "R2" LARGE CUTTING OVERALL
3224 1/4" 1 1/2" 5/8" 2 1/8" NUMBER RADIUS RADIUS DIAMETER LENGTH LENGTH

1/2" SHANK 1/4" SHANK

3222 5/32" 1 1/8" 1/2" 2 1/4" 3270 3/16" 5/16" 1 1/2" 5/8" 2 1/8"
3226 1/4" 1 1/2" 5/8" 2 3/8" 1/2" SHANK
3228 9/64"&5/16" 1 5/8" 5/8" 2 1/2" 3272 3/16" 5/16" 1 1/2" 5/8" 2 1/2"
Bearing Number: B3 Bearing Number: B3

Visit us online: www.klingspor.com 21 ROUTER BITS

 EDGE PROFILES
CLASSICAL OGEE
FRENCH PROVINCIAL MOLDING
French Provincial Molding bits can be used alone or in conjunction with other TABLE EDGE
profiles to create decorative moldings to accent any room or workpiece. It Classical Ogee Table Edge bit is used as a profile option for
produces a small full bead part way down from the top and transitions into tables or large a workpiece or in conjunction with a
step-round at the bottom. This is similar to the cove and bead, but adds a handrail bit to create custom handrail tops. Carbide
full bead on the top. Carbide tipped two-wing cutter. tipped two-wing cutter.

3298

PART LARGE CUTTING BEAD OVERALL

NUMBER DIAMETER LENGTH DIAMETER LENGTH
PART PROFILE LARGE CUTTING OVERALL
1/2" SHANK NUMBER WIDTH DIAMETER LENGTH LENGTH
3280 1 3/4" 1 1/8" 1/4" 3 1/8"
1/2" SHANK
Bearing Number: B3 3298 1" 2 1/2" 3/4" 2 1/2"
#3282 - See Cove & Bead Bits on page 21.
Bearing Number: B3

THUMBNAIL TABLE EDGE

Thumbnail Table Edge bits are used as a decorative edge for tables
or large panels or as part of a handrail profile (3294). Carbide FRENCH BAROQUE
tipped two-wing cutter. TABLE EDGE
3290 French Baroque Table Edge bit is a large symmetrical
& 3292 profile that produces a cove at the top and bottom
and a bead in the middle. It can be used alone
or with other bits to create stunning and eye-
catching moldings and project edges.
Carbide tipped, two-wing cutter.
3294 3300

PART PROFILE LARGE CUTTING OVERALL

NUMBER WIDTH DIAMETER LENGTH LENGTH
1/4" SHANK
3290 7/16" 1 3/8" 3/8" 1 7/8"
1/2" SHANK PART PROFILE LARGE CUTTING OVERALL
3292 7/16" 1 3/8" 3/8" 2" NUMBER WIDTH DIAMETER LENGTH LENGTH
3294 1" 2 1/2" 3/4" 2 1/2"
Bearing Number: B3
1/2" SHANK
3300 7/8" 2 1/4" 3/4" 2 1/2"
Bearing Number: B3

TRADITIONAL
TABLE EDGE THUMBNAIL & BEAD
Traditional Table Edge bits are another popu- TABLE EDGE
lar choice edges on larger panels, tables Thumbnail & Bead Table Edge bit is a thumbnail pro-
and more. It produces a soft cove and file with a small, simple bead at the top, which
bead. Carbide tipped two-wing cutter. adds a nice accent to any large panel or table top.
Carbide tipped, two-flute cutter.
3302

3296
3228

PART PROFILE LARGE CUTTING OVERALL PART PROFILE LARGE CUTTING OVERALL
NUMBER WIDTH DIAMETER LENGTH LENGTH NUMBER WIDTH DIAMETER LENGTH LENGTH
1/2" SHANK 1/2" SHANK
3228 9/16" 1 5/8" 5/8" 2 1/2" 3302 1" 2 1/2" 3/4" 2 1/2"
3296 1" 2 1/2" 3/4" 2 1/2"
Bearing Number: B3
Bearing Number: B3

ROUTER BITS 22 Call Toll Free 800-645-5555

 HANDRAIL & MOLDING
HANDRAIL BITS SPECIALTY MOLDING
Used to cut the lower portion of Specialty Molding bits are offered with several profile options from a
the handrail profile. simple bead and cove to a bead, cove, bead profile. They are designed
Handrail bits are designed to be used with other bits (see image below) to to be used alone or with other bits to create more elaborate profiled
create wooden handrails. Two basic profiles are offered with similar cuts. moldings. Carbide tipped, two-wing cutter.
One is large and the other is small. Carbide tipped, two-wing cutter.

3304
3320 3324 3326 3330
3305
PART LARGE CUTTING BEAD OVERALL
NUMBER DIAMETER LENGTH DIAMETER LENGTH
1/2" SHANK
3320 1" 1" 5/16" 2 3/4"
3324 7/8" 1 5/8" 5/16" 3 1/2"
PART LARGE CUTTING BEAD OVERALL 3326 1 1/16" 1 5/8" 1/4" 3 1/2"
NUMBER DIAMETER LENGTH DIAMETER LENGTH 3330 1" 1 5/8" 1/4" 3 1/2"
Bearing Number: B3
1/2" SHANK
3304 1 3/8" 1 1/2" 1/4" 3 3/8"
3305 1 1/4" 2" 1/4" 3 7/8"
Bearing Number: B3

CLASSIC MULTI-FORMS
Many distinct profiles are possible by
using different sections of this tool.
Classic Multi-Form bits produce several molding
profiles in one bit. The top portion creates
coves or beads and the bottom creates an
HANDRAIL PROFILES edge bead. Simply raise or lower the router
Here are some examples of the handrail profiles which are possible using the handrail bits above in bit or bring the router fence in or out, you can
combination with your choice of the table edge bits from page 20. produce over 40 different profiles. Carbide tipped,
two-wing cutter.

3294 & 3305 3298 & 3304

2" 2"

3340
3342
2 1/2"
PART LARGE CUTTING BEAD RADIUS OVERALL
2 1/16" NUMBER DIAMETER LENGTH DIAMETER LENGTH
1/2" SHANK
3340 1 3/8" 1" 1/4" 3/16" 2 3/4"
3342 2 1/4" 1 7/8" 1/2" 5/16" 3 3/4"
Bearing Number: B3

Visit us online: www.klingspor.com 23 ROUTER BITS

 GLUE JOINTS
Locking Drawer Glue Joint bits (3346, 3347, 3350, &3352) are the perfect tool for making drawers
from wood. One bit does it all. After the proper height is set, it is just a matter of running the drawer
front with the outside face up, flat on the table. The side pieces are machined vertically, their inside ONE TOOL MAKES BOTH CUTS
faces against the fence and cutter. Carbide tipped, two-wing cutter.

LOCKING DRAWER GLUE JOINTS

45° LOCK MITER
45° Lock Miter bits deliver double the glue surface of a traditional 45° miter.
It creates both the miter and a joint lock at the same time, which prevents
movement when clamping pressure is applied. Board “A" is ran horizontally,
while board “B" is ran vertically. Carbide tipped, two-wing cutter.

PART MATERIAL LARGE SHANK OVERALL

NUMBER THICKNESS DIAMETER DIAMETER LENGTH
3360 1/2-1 1/4" 3 1/8" 1/2" 2 7/8"
3362 1/2-3/4" 2" 1/2" 2 3/8"
DRAWER FRONT
ONE TOOL MAKES BOTH CUTS
Note: 3362 is recommended for stock thickness 1/2 - 3/4"
PART LARGE CUTTING SHANK OVERALL
NUMBER DIAMETER LENGTH DIAMETER LENGTH

3346 3/4" 1/2" 1/4" 1 7/8"

3347 1" 1/2" 1/2" 2 1/8"

LOCKING DRAWER GLUE JOINTS

WEDGE TONGUE
& GROOVE
Wedge Tongue & Groove bits are the ideal bits for joining two
ONE TOOL MAKES BOTH CUTS boards together where strength and alignment are important. This set is for joints that are glued along
the length. The wedge shape of the tongue increases the glue surface - adding to the strength of the
joint. This set should only be used in a router table. Carbide tipped, two-wing cutter
PART MATERIAL LARGE SHANK OVERALL
NUMBER THICKNESS DIAMETER DIAMETER LENGTH
1/2" SHANK
DRAWER FRONT 3370 5/8-1 1/4" 1 1/4" 1 1/4" 2 7/8"
* Order 3370 for Two Piece Set.
PART LARGE CUTTING SHANK OVERALL * Order 3370A or 3370B for individual cutters.
NUMBER DIAMETER LENGTH DIAMETER LENGTH
3350 1" 1" 1/4" 2 3/8"
3352 1" 1" 1/2" 2 3/8"

3373A 3373B

STRAIGHT
ONE TOOL MAKES BOTH CUTS
TONGUE & GROOVE
Ball Bearing Guide
Straight Tongue & Groove bits are the ideal bits for joining two boards together where strength and
STANDARD GLUE JOINT alignment are important. This set makes the Tongue and Groove joint in its simplest form. Both sides of
Standard Glue Joint bit provides lots of glue surface to join boards together. One cutter makes both the joint are straight and square. Each side is formed with its own bit. This set works best when used in
cuts, so no need to make two set-ups. Board “A" runs face down and board “B" face up. A test piece a router table with the fence in line with the bearing. Carbide tipped, two-wing cutter
may be required to fine tune the set up. Carbide tipped two wing cutter.
PART MATERIAL LARGE SHANK OVERALL
NUMBER THICKNESS DIAMETER DIAMETER LENGTH
PART MATERIAL LARGE SHANK OVERALL
NUMBER THICKNESS DIAMETER DIAMETER LENGTH 1/2" SHANK
3373 1/2"- 1 1/4" 1 1/4" 1 1/4" 3 1/8"
3354 1/2-1 1/4" 1 1/2" 1/2" 2 3/4" * Order 3373 for two piece set
* Order 3373A or 3373B for individual cutters.
Bearing Number: B7

ROUTER BITS 24 Call Toll Free 800-645-5555

 GLUE JOINTS
3374A

3374B

VEE PANEL TONGUE & ONE TOOL MAKES BOTH CUTS

GROOVE Ball Bearing Guide

Vee Panel TongueStraight Tongue & Groove bits are the ideal bits for joining two boards together where FINE FINGER JOINT
strength and alignment are important. This set makes the Tongue and Groove joint in its simplest form. Fine Finger Joint bit makes a super strong joint when end joining is required. It
Both sides of the joint are straight and square. Each side is formed with its own bit. This set works best features wedge-shaped multiple interlocking fingers. This creates a maximum gluing
when used in a router table with the fence in line with the bearing. Carbide tipped, two-wing cutter & surface area and helps to minimize gaps when routing edge joints and even end grain
Groove bits this set makes a tongue and groove joint with a decorative V groove along the length of the to end grain. Carbide tipped.
joint. It is typically used in tongue and groove paneling or ceilings. This set should only be used in a router
table with the fence in line with the bearing. Carbide tipped, two-wing cutter
PART MATERIAL LARGE FINGER OVERALL
PART MATERIAL LARGE CUTTING OVERALL NUMBER THICKNESS DIAMETER DEPTH LENGTH
NUMBER THICKNESS DIAMETER LENGTH LENGTH
1/2" SHANK 1/2" SHANK
3390 5/16-1 1/4" 1 3/8" 5/16" 3 1/4"
3374 5/8-1"* 1 5/8" 1" 2 3/4"
Bearing Number: B4
Order 3374 for two piece set.
Order 3374A or 3374B for individual cutters.
* Material over 1" thick requires a second cut on the tongue profile to waste away excess stock.

ONE TOOL MAKES BOTH CUTS

TONGUE & GROOVE ASSEMBLY

Tongue & Groove Assembly bit is the most economical way to make tongue and groove joints. The
PART #3506
single bit is used to make both sides of the joint, simply by adjusting the height of the bit to change
from tongue to groove. Carbide tipped. FLUSH RIBBED

PART MATERIAL LARGE CUTTING OVERALL MULTI SIDE BITS

NUMBER THICKNESS DIAMETER LENGTH LENGTH A great way to join up many multi-side projects (planters, columns, barrels, etc.). Very straightforward,
1/2" SHANK this joint requires routing a notch in only one edge of each stave (side). Notching also improves ease
3375 1/2"-13/16" 1 5/8" 9/32" B5 of assembly and total glue area. All bits are 1/2" shank and are designed for use in a router table with
Replacement Parts: Groover - 6628 a fence guide.
Arbor - A260
PART NUMBER STOCK LARGE
USING THE TONGUE & NUMBER OF SIDES (MAXIMUM) DIAMETER
GROOVE ASSEMBLY 1/2" SHANK
3506 6 or 12 7/8" 1 7/8"
3508 8 7/8" 1 3/4"
3516 16 1" 1 5/8"
On six and eight sided objects, the exterior side is cut face up on a router table. Twelve and sixteen
EDGE BANDING SET sided objects are cut face down. The same bit (#3506) is used for six sided and twelve sided objects.
Either Flush or Ribbed (outside corners protruding) construction is possible. Ribbed construction
This bit set will allow the customer to make their own hardwood
edge banding for plywood, particle board, or MDF stock. It enables is recommended with 12 and 16 sides because the interior leg of the notch will be very small when made
them to make their own hardwood edge banding match the rest flush. Outside corners on ribbed construction can be cut or sanded down for flush appearance if desired.
of the project instead of having to buy a thin veneer edge tape Location of the inside corner of the notch (i.e.- vertical bit adjustment) is important for final
to be glued on. It’s designed for stock up to 3/4" thick, which is finish appearance. The outside leg of the notch (closest to the exterior) should be the same length as
standard sheet good thickness, and features carbide tips and 1/2" the stock thickness for flush construction. This will put the inside corner of the notch in the center of the
shank. The advantage of this is a stronger edge than that of the stave on six sided flush projects. The inside corner will be below center (furtherest from exterior side) on
thin veneer tape. It can be routed with a profile or left square depending on the all others. Allow extra stock to experiment and set corner height as desired. Move notch towards exterior
application. Adding hardwood banding to veneered plywood shelves and table tops. side (raise the bit) to increase rib size (amount of outside corner protruding). Move notch away from
• One bit will put a “V" shaped, concave profile in the plywood. exterior side (lower the bit) to decrease amount of rib. Note: Bit adjustment is reversed on twelve and
• While the other bit forms a perfect match in hardwood.
sixteen sides since those staves are cut face down.
• Top and bottom of the banding can be trimmed flush using the router or hand plane.
• For use on stock that is less than 13/16" in thickness.

PART CUTTER MATERIAL

NUMBER LENGTH THICKNESS
1/2" SHANK
3400 13/16" 3/4"

Visit us online: www.klingspor.com 25 ROUTER BITS

 GROOVE PROFILES
Small Grooving Bits are commonly used for decorative designs in cabinet doors or for detail veining
in furniture. Round Nose Bits (pg. 9) and V-Groove Bits (pg. 10) are often used in the same manner. The
Larger Grooving Bits are great for a raised panel effect in doors and for adding a bold accent to furniture or
large workpieces. These bits also make nice edge profiles with the aid of a router table and fence. 3770

These bits are ideal for adding bearings to the shank for following templates. Select a bearing from
page 37 with the same inside diameter as your shank size. Outside diameter should be the same size or SHOWN WITH B17 BEARING

larger than the large diameter of your router bit. Secure bearings with a lock collar. Use Lock Collar #LC-1/4
for 1/4" shanks or LC-1/2 for 1/2" shanks.
3780
2051

A
B

3602
C CLASSICAL FLAT BOTTOM
PART RADIUS LARGE CUTTING OVERALL
NUMBER DIAMETER LENGTH LENGTH
3604 & 3606 3608
PLUNGE 1/4" SHANK
3770 7/64" 3/4" 3/8" 2"
OGEE
1/2" SHANK
"A" "B" "C" 3780 13/64" 1 3/8" 9/16" 2 1/2"
PART RADIUS SMALL LARGE CUTTING OVERALL
NUMBER DIAMETER DIAMETER LENGTH LENGTH
1/4" SHANK
2051 3/16" 1/4" 5/8" 3/8" 1 3/4"
3602 3/32" 1/8" 1/2" 1/4" 1 3/4"
3604 3/16" 3/16" 7/8" 1/2" 2"
1/2" SHANK
3606 3/16" 3/16" 7/8" 1/2" 2"
3608 3/16" 3/8" 1 1/8" 1/2" 2 1/4"

3750

3720 3725

3730 & 3735 3740

CLASSICAL ROUND BOTTOM

PART RADIUS LARGE CUTTING OVERALL
NUMBER DIAMETER LENGTH LENGTH
1/4" SHANK
3720 1/8" 5/8" 1/2" 2"
3725 1/8" 3/4" 1/2" 2"
3730 3/16" 7/8" 1/2" 2"
1/2" SHANK
3735 3/16" 7/8" 1/2" 2 1/8"
3740 3/16" 1 1/8" 1/2" 2 1/8"
3750 7/32" 1 3/8" 9/16" 2 1/2"

ROUTER BITS 26 Call Toll Free 800-645-5555

 MDF DOORS
The Tooling on this page is designed to give the illusion of raised panel door construction in MDF and solid panel doors. These bits, when
used individually, produce a nice simple raised panel effect in one pass. Or use one of the "Panel" bits in conjunction with one of the "Stile" bits
to create a more authentic raised panel reveal. Many different combinations are possible. See Bottom of Page. Although designed for production
routing on solid door machines and CNC routers, the addition of a bearing to the shank will allow the hobbyist to cut his pattern by following an

Panel
Stile
edge guide. The guide can be four strips clamped around the perimeter of the door. The top strip may be curved for an arched pattern. Follow
the guide and rout both profiles. There’s no need to move the guide for the second cut. A larger bearing on the panel bit takes care of the offset.
Use Bearing #B16 for the Stile bits and Bearing #B24 for the Panel bits. Secure the bearings to the shank with a #LC-1/2 Lock Collar (see pg.
36). When making the second cut, match the depth setting of the first cut to obtain a pattern with a flat bottom - Or vary the depth to add
an extra distinctive "step" in the bottom of your reveal. Complete the door by adding a door edge pattern (see Pg. 29) around the outside edge.

"STILE" PROFILE BITS "PANEL" PROFILE BITS

5620

#5620

5630 5710

#5630 #5710
* with bearing only

5610 5645 5720 5725

#5610 #5645 #5720 #5725

PROFILES SHOWN ACTUAL SIZE

PART STYLE LARGE OVERALL PART STYLE LARGE OVERALL
NUMBER DIAMETER LENGTH NUMBER DIAMETER LENGTH
1/2" SHANK 1/2" SHANK
5610 Bead 7/8" 2 1/2" 5710 Cove 1 1/2" 2 1/2"
5620 Traditional 1 1/4" 2 1/2" 5720 Straight 1 1/2" 2 1/2"
5630 Ogee 1 1/4" 2 1/2" 5725 Ogee 1 1/2" 2 1/2"
5645 Straight 1 1/4" 2 1/2"

STILE & PANEL COMBINATION PROFILES

5610 & 5710 5610 & 5720 5610 & 5725

OPTIONAL - 2057 & 97-320 FOR UNIQUE MACHINE

5620 & 5710 5620 & 5720 5620 & 5725

5630 & 5710 5630 & 5720 5630 & 5725

5645 & 5710 5645 & 5720 5645 & 5725

Visit us online: www.klingspor.com 27 ROUTER BITS

 STILE & RAIL
STILE RAIL
MINIATURE STILE & RAIL
These miniature Stile and Rail sets work just like their full size counterparts (see below). They feature a reduced pattern
and a reduced tongue and groove (5/32" x 1/4") suitable for smaller projects. Works with 7/16" to 3/4" thick stock.

SET PATTERN REVEAL LARGE STOCK

5740 - ROUND NUMBER WIDTH DIAMETER SIZE
1/2" SHANK
5740 Round 3/16" 1 1/8" 7/16"-3/4"
5742 Ogee 1/4" 1 1/8" 7/16"-3/4"
For Individual Bits: Add A to Part Number for Stile Cutter.
Add B to Part Number for Rail Cutter.
5742 - OGEE Example: 5740A - Round Stile Cutter
Replacement Parts: Stile Groover - 5740AG
Rail Groover - 5740BG
Bearing - B27

STILE RAIL

FULL SIZE STILE & RAIL

Make full size Stile and Rail joints on your router table. The interlocking
design plus the raised panel groove are both cut in one pass. Ball bearing
guides control the cutting depth and also allow use on rounded, arched,
MATCHED
or special shaped doors. With these two piece sets, simply switch router SETS
6001 - ROUND bits to change from cutting stiles to cutting rails. Ideal for stock from 5/8"
to 7/8" thick.
SET PATTERN REVEAL CUTTING LARGE
NUMBER WIDTH LENGTH DIAMETER
1/2" SHANK
6001 Round 1/4" 1" 1 5/8"
6002 Ogee 3/8" 7/8" 1 5/8"
6003 Bead 3/8" 7/8" 1 5/8"
6002 - OGEE
6004 Straight 3/8" 7/8" 1 5/8"
6005 Traditional 3/8" 7/8" 1 5/8"
6006 Classical 3/8" 7/8" 1 5/8"
For Individual Bits: Add A to Part Number for Stile Cutter.
Add B to Part Number for Rail Cutter.
Example: 6001A - Round Stile Cutter
Replacement Parts: Groover - 6625
Bearing - B5
6003 - BEAD

PLYWOOD PANEL STILE & RAIL

This set-up is for cabinet door construction with undersized 1/4" plywood panels. (Actual panel thickness of 7/32" or 5.5 mm).
KLINGSPOR’s conversion kit #6000X converts the regular full size Stile and Rail Bits to the narrower groove required for these plywood
panels. This kit gives you the flexibility to do either plywood panels or raised panels. Plus, it can be used on any KLINGSPOR full size Stile
and Rail bits that you may already own.
6004 - STRAIGHT
Our two most popular Stile and Rail sets are also available ready to use just for plywood panel construction. Order Part Number 6001X
for round pattern or Part Number 6002X for ogee pattern. 1/2" Shank only.

NOTE: Add #6625 to make

top portion thicker
3/8"

6005 - TRADITIONAL 5/16"

SHAKER STYLE STILE & RAIL
5990
DESCRIPTION: 7/32" Groove for undersized plywood

6006 - CLASSICAL
16-284
DESCRIPTION: 1/4" Groove

ROUTER BITS 28 Call Toll Free 800-645-5555

 RAISED PANEL

5750

5751
5900A
6000A 5900C
6000C

MINIATURE RAISED PANEL BITS 5900B

1 3/4" Diameter - 1/2" Shank 6000B
Ball Bearing Guide 5900F
6000F
These raised panel bits offer a reduced pattern ideal for smaller projects. Available in your choice of
cove or ogee profile shown below. To work with the miniature stile and rail bits, set bit depth to leave
a 5/32" thick tongue. Leaves only a 3/8" panel reveal after assembly! Now you can use raised panel 5900E
construction for small doors, chests, jewelry boxes, etc. 6000E

5900H
5900G 6000H
6000G
5950

LARGE RAISED PANEL BITS

5951 5900 Series - 2 wing - 3 1/4" Diameter
6000 Series - 3 wing - 3 3/8" Diameter
1/2" Shank - Ball Bearing Guide

5952

5920B

5953

5920C
5954

MEDIUM RAISED PANEL BITS 5920E

2 1/2" Diameter - 1/2" Shank Ball Bearing Guide
These bits cut a 1" wide pattern and are often used for general edge profiles in addition to raised panels. LARGE RAISED PANEL BITS
They can be used with the miniature or the full size stile and rail bits. See our great selection of profiles
available at left.
with BACK CUTTER
2 wing (2+2) - 3 1/4" Diameter
1/2" Shank - Ball Bearing Guide
This Panel Bit with Back Cutter allows you to cut the Front Reveal and the optional Back Cut at the same
time - and guarantees a 1/4" tongue in the process.

Visit us online: www.klingspor.com 29 ROUTER BITS

 CABINET DOORS
RAISED PANEL DOOR CONSTRUCTION
Choose stock size as appropriate for your project. For example, 3/4" x 2" stile & rails and 5/8" thick panels (without optional back cut) are common for cabinet doors. Use your stock size and door
size to calculate the following:

• Stile length = Door height

• Rail length = Door width - width of both stiles + Interlock
• Panel height = Door height - width of both rails + Interlock - Expansion
• Panel width = Rail length - Expansion
• Interlock = 3/4" (3/8" per side) on KLINGSPOR full size Stile & Rail bits or 1/2" (1/4" per side) for KLINGSPOR miniature Stile & Rail.
• Expansion: Generally 1/8" on cabinet doors. Can vary with door size, green condition of wood, anticipated exposure to high humidity,
and species of wood.
• Use the Stile bit to cut the entire length of the inside edge on both the stiles and the rails.
• Use the Rail bit to make the matching cross grain end cuts on the rails only.
• Use the Raised Panel bit to cut all four sides of each raised panel face down on the router table.
Set Raised Panel bit height for proper tongue thickness. Tongue should be 1/4" for the full size Stile & Rail bits or 5/32" for the
miniature ones. Allow extra stock if you plan to use the optional back cutter.
• Use the Standard Glue Joint (page 24) or biscuits for added strength when gluing up larger panels.
• Cut all components and test fit. Then glue up and reassemble. Glue only the stile and rail joints. The panel should be allowed to "float" to allow for expansion and contraction. You may
choose to use anti-rattle snakes to prevent the panel from rattling. Make your own by running a 1/8" bead of 100% silicone caulk on wax paper. Allow to dry. Cut into pieces about 3/4"
long. Insert in each groove at every corner while assembling. Check the door for squareness immediately after gluing up. It may also be helpful to pre-stain the raised panel because part
of the concealed portion of the tongue may become visible later due to contraction. Complete the door by adding a door edge pattern (page 31) around the outside edge.

PART #5850

RAISED PANEL BACK CUTTER

This bit offers a safe and economical way to make that optional
backside cut on raised panels. It is suitable for use with any of our
Raised Panel Bits on page 29. 1 3/4" large diameter with 1/2 shank.
Order part #5850.

5801 5804

5802

STILE RAIL

VERTICAL PANEL BITS

1" Diameter - 1/2" Shank
STILE & RAIL GLASS DOORS 1 1/2" Cut Length
Make the Stile & Rail cuts for glass doors using KLINGSPOR’s full size Stile & Rail Sets on page 28. No extra
components are required. All that’s needed is to stagger the cutting edges and "stack" both groovers on the
Stile bit. Use both bearings (no groover) on the Rail bit. See Drawing. Now make your cuts just like in normal Vertical Panel Bits offer a method to cut full size raised panels with a smaller router bit
door construction - requiring less horsepower. These bits are usually run in a router table with the panel standing
on edge and the face of the panel against the fence. Fence must be tall enough to properly
Cut the inside edges of all four pieces with the Stile Bit. Trim the ends of the Rails with the Rail bit. Assemble support the panel. Use on straight sided panels only since there is no bearing guide for arched
door and insert glass pane. Use clips or corner trim mold on the back side to hold the pane in place. or cathedral style doors.

ROUTER BITS 30 Call Toll Free 800-645-5555

 DOOR & DRAWER EDGE

#6010
6026
6024

DRAWER PULL - EUROPEAN STYLE

Drawer Pull – European style bits are a deeper style finger pull milled into the drawer
front where hardware will not be installed.
#6015 #6016
PART LARGE LARGE CUTTING OVERALL
NUMBER RADIUS DIAMETER LENGTH LENGTH
DOOR EDGE BITS Complete Edge 1/2" SHANK
Door Edge Bits with the complete edge offer three options to choose from. The recessed profile creates 6024 3/16" 3/4" 7/8" 2 3/8"
an overhang to lip over the cabinet side or face frame. The finger pull produces a lip to grip the door 6026 1/4" 1 1/2" 13/16" 2 3/8"
from the back side for easier opening when no hardware will be used. The reversible, as the name
implies, allows for a complete reversible finger pull to be milled on both sides of the door.
PART LARGE CUTTING STYLE
NUMBER DIAMETER LENGTH 6032

1/2" SHANK Drawer

6010 1 3/8" 1 1/8" Recessed Doors Front

6015 1 1/2" 7/8" Finger Pull

6016 1 5/8" 15/16" Reversible

DRAWER EDGE FINGER PULL

Produces a nice smooth finger grip primarily used on the bottom edge of drawer fronts. Also
used as a finger pull on cabinet doors where no edge pattern is needed on the front face.
PART LARGE CUTTING OVERALL
NUMBER DIAMETER LENGTH LENGTH
1/2" SHANK
6032 1 1/4" 3/4" 2 1/2"
Bearing Number: B3

3290 & 3292 6020

6021 6022 6023

DOOR EDGE BITS

Front Face Edge Ball Bearing Guide
These bits cut a decorative profile along the front face of the door edge while leaving most of the edge
straight. Their shallow design works well with concealed European style cup hinges. Many of our other 6045 6046
edge profile bits also make great door edges. (Deeper profiles may not be compatible with European
style cup hinges). WINDOW SILL EDGE/
PART LARGE CUTTING OVERALL
FINGER PULL
NUMBER DIAMETER LENGTH LENGTH Originally designed to cut the front edge of window sills, this bit has also
become popular for making a rounded finger edge on both drawers and door
1/4" SHANK edges.Use with a router fence or add a shank mounted bearing for following a
3290 1 3/8" 3/8" 1 7/8" straight edge or template.
1/2" SHANK PART LARGE PROFILE OVERALL
3292 1 3/8" 3/8" 2" NUMBER RADIUS DIAMETER LENGTH LENGTH
6020 1 9/16" 3/8" 2 1/4"
6021 1 3/4" 3/8" 2 1/4" 1/2" SHANK
6022 1 3/4" 3/8" 2 1/4" 6045 7/32" 1 1/4" 13/16" 2 7/8"
6046 3/8" 1 7/16" 1 1/8" 3 3/8"
6023 1 3/4" 3/8" 2 1/4"
Use Bearing (B16 for #6045, B18 for #6046) and Lock Collar (LC-1/2) on Shank for

Template Work.

Visit us online: www.klingspor.com 31 ROUTER BITS

 WINDOW SASH • DOVETAIL SETS
Stile

INCRA DOVETAIL SETS

Top Quality Dovetailing Sets for use with the popular Incra System. Choose the #D101 Set (1/4" Shank) for
the smaller Dovetails (1/4", 3/8", 1/2", 17/32"). Take the #605 Set (1/2" Shank) for the heavier 3/8", 1/2",
Rail
5/8", & 3/4" Dovetail bits. Both Sets also include the 1/4" and 3/8" Box Joint Bits.

PART# DESCRIPTION
D101 6 Piece Incra Set - 1/4" Shank
605 6 Piece Incra Set - 1/2" Shank

All bits available individually. See next page.

PROFILE
CUTTER SPACER
STILE RAIL
PROFILE
END CUTTER
CUTTER

ACTUAL SIZE
STILE CUT RAIL CUT

WINDOW SASH LEIGH DOVETAIL SETS

This is the only bit you need to make a complete window sash. The bearing guide controls the pattern
depth and also allows you to make arched or curved windows and glass doors. Upgrade to KLINGSPOR Quality Bits for your Leigh Jig. The smaller bits are supplied in the recommended
8mm Shanks (1/2" Adapter Collet is included). The largest sizes come in 1/2" shanks. Improved
This assembly with the straight end cutter cuts the inside edges on both the stiles and rails. Convert the Performance Guaranteed.
assembly to make the mating end cut by exchanging the straight cutter for the spacer (see drawing. The
spacer can be installed between the profile cutter and the shank if additional reach across the workpiece
is needed.) Now make the mating end cuts on the rails. This bit can also be used to cut both the PART# DESCRIPTION
decorative edges and the mating end cuts required to make your own window mullions (crosspieces). D108 7 Piece Leigh Set. Includes D8-437x8, D8-687, D14-51x8,
D18-50x8, 1020x8,1067, and 6400x8 Adapter.
PART CUTTING CUTTING OVERALL D116 6 Piece Leigh Set for #D1600 16" Jig. All bits 8mm
NUMBER DIAMETER LENGTH LENGTH Shank. 6400x8 Adapter Collet to 1/2" is included.
6050 1 3/8" 7/8 - 1 5/8" 3 5/8" Complete with the following bits: 1020x8, D8-375x8,
D8-500x8, D14-51x8, D18-50x8 .
Replacement Parts: Profile Cutter: 6050H
Arbor: A380 Straight Cutter: 6050G All bits available individually. See next page.
Bearing Number: B5 Spacer: 6050SP

ROUTER BITS 32 Call Toll Free 800-645-5555

 DOVETAIL BITS
PART LARGE DEPTH SHANK OVERALL CROSS
DOVETAIL BITS NUMBER DIAMETER OF CUT DIAMETER LENGTH REFERENCE
7° ANGLE
Premium Quality Dovetail D7-531 17/32" 3/4" 1/2" 2 1/2" P•C #43776PC
Bits to meet all your D7-622 5/8" 7/8" 1/4" 2 3/8
Dovetailing Needs D7-625 5/8" 7/8" 1/2" 2 5/8" Incra™
Dovetail bits are popular for both their decorative and D7-750 3/4" 7/8" 1/2" 2 5/8" Incra™
very functional joint. Made using a combination of a *
D7-875 7/8" 7/8" 1/2" 2 1/2" Stair Tread
7 1/2° ANGLE
dovetail and a straight bit, these bits work well with SC D75-25 1/4" 5/16" 1/4" 2 1/2" Incra™/OmniJig® 43639
many jigs manufactured on the market. Some bits are 8° ANGLE
noted specifically to replace certain manufacturer’s bits. SC D8-250 1/4" 1/4" 1/4" 2 1/2" Leigh #50
These create a modern version of the hand cut dovetail SC D8-250x8 1/4" 1/4" 8mm 2 1/2" Leigh #50-8mm shank
used for centuries. D8-312 5/16" 3/8" 1/4" 2 1/4" Leigh #60
They are available in several angles from 7° to 18° and D8-312x8 5/16" 3/8" 8mm 2 1/4" Leigh #60-8mm shank
some sizes are made of solid carbide. D8-375 3/8" 1/2" 1/4" 2 3/8" Leigh #70
D8-375x8 3/8" 1/2" 8mm 2 3/8" Leigh #70-8mm shank
D8-437 7/16" 5/8" 1/4" 2 3/8" Leigh #75
D8-437x8 7/16" 5/8" 8mm 2 3/8" Leigh #75-8mm shank
D8-500 1/2" 13/16" 1/4" 2 3/4" Leigh #80
D8-500x8 1/2" 13/16" 8mm 2 3/4" Leigh #80-8mm shank
D8-687 11/16" 1" 1/2" 3" Leigh #90
D8-812 13/16" 1 1/4" 1/2" 3 1/4" Leigh # 100
9° ANGLE
D9-312 5/16" 3/8" 1/4" 2 1/4" Incra™
D9-372 3/8" 3/8" 1/4" 2" Incra™
D9-373 3/8" 3/8" 3/8" 2"
*with 1/2" shank only
* D9-375 3/8" 3/8" 1/2" 2"
* D9-376 3/8" 3/8" 1/2" 2 1/2" Incra™
* D9-390 .390 3/8" 1/2" 2"
10° ANGLE
D10-50 1/2" 5/8" 1/4" 2 1/2" Incra™/Leigh #101
D10-50x8 1/2" 5/8" 8mm 2 1/2" Leigh #101-8mm shank
D10-55 1/2" 5/8" 1/2" 2 5/8" Incra™
14° ANGLE
D14-375 3/8" 3/8" 1/4" 2"
D14-50 1/2" 1/2" 1/4" 2" Incra™/OmniJig® #43705
D14-51 1/2" 1/2" 1/4" 2 3/8" Leigh #120
D14-51x8 1/2" 1/2" 8mm 2 3/8" Leigh #120-8mm shank
* D14-55 1/2" 1/2" 1/2" 2 1/2" Incra™/OmniJig® #43750
D14-531 17/32" 1/2" 1/4" 2" Incra™
D14-72 3/4" 3/4" 1/4" 2 3/8"
D14-75 3/4" 3/4" 1/2" 3" OmniJig® #43774
D14-100 1" 7/8" 1/2" 2 1/2"
18° ANGLE
D18-50 1/2" 3/8" 1/4" 2 1/4" Leigh #128
D18-50x8 1/2" 3/8" 8mm 2 1/4" Leigh #128-8mm shank
STRAIGHT BITS
1020 5/16" 1" 1/4" 2 3/4" Leigh #140
1020x8 5/16" 1" 8mm 2 3/4" Leigh #140-8mm shank
1064A 13/32" 1" 1/2" 2 1/2" P•C #43743PC
1065L 7/16" 1 1/4" 1/2" 3 1/4" Leigh #150
1067 1/2" 1 1/4" 1/2" 2 7/8" Leigh #160
*Also Stocked in Left Hand. Add LH to Part Number. SC - Solid Carbide All bits designated Incra™ are also compatible with the
JoinTech™ system

KELLER DOVETAIL BITS

KLINGSPOR Abrasives, Inc. offers precision router bits to match Keller’s unique
dovetailing system. All tools listed below are supplied with the required ball bearings.
PART KELLER LARGE CUTTING SHANK OVERALL
NUMBER NUMBER DIAMETER LENGTH DIAMETER LENGTH
7° ANGLE DOVETAIL
K31 1631 11/32" 3/8" 1/4" 2 1/4"
K33 1633 7/16" 3/4" 1/4" 2 5/8"
K35 2435 5/8" 1" 3/8" 2 5/8"
STRAIGHT BITS
K41 1641 5/8" 1/2" 1/4" 2 1/4"
K43 1643/2443 5/8" 3/4" 1/4" 2 1/2"
3015 2445 7/8" 1" 3/8" 2 5/8"
* 3032 1642 9/16" 3/4" 1/4" 2 1/4"

*Box Joint Bit

Visit us online: www.klingspor.com 33 ROUTER BITS

 SPOILBOARD •SLOTTING
SLOTTING CUTTERS
CNC SPOILBOARD SURFACING 1 7/8"Cutting Diameter -
CNC Spoilboard Surfacing bits are used to remove material from the scrap board so
5/16" Bore
that the actual work piece can be milled on
Slotting Cutters are designed to make slots (grooves) along the
the CNC table without movement. Cutting
edges of boards and are far superior to straight bits for doing
applications include spoilboard, planing and
so. They are designed to be used with slotting cutter arbors
rabbeting large surface areas in MDF, Balsa Core, hardwood, softwood and many
and are available in a 3-wing or 4-wing design. Carbide
other man-made materials. These spoilboard bits were engineered to produce a
tipped.
high quality cut, maximum cutting efficiency, faster material removal process and
long tool life. PART NUMBER KERF
3 wing 4 wing Decimal Fractional
The industrial router bit features insert knives (three to four per bit) with four cutting 6700A 6700B .062 1/16"
edges that allow users to flip the knife over when one side becomes dull and is available 6701A .070 ---
in 1/2" and 3/4" shank size. 6702A .080 ---
6703A 6703B .094 3/32"
Choose straight cut for particle board and MDF surfacing or up-shear cut for balsa core material. 6704A .100 ---
6704C .110 7/64"
PART LARGE SHANK # OF 6705A 6705B .125 1/8"
NUMBER DIAMETER SIZE WINGS 6708A .156 5/32"
6709A .187 3/16"
STRAIGHT CUT 6709C .218 7/32"
SB25-2 2 1/2" 1/2" 2 6710A 6710B .250 1/4"
SB40-2 4" 3/4" 2 6712A .281 9/32"
SB40-3 4" 3/4" 3
UP SHEAR CUT Special Sizes Available Upon Request
SBU25-2 2 1/2" 1/2" 2
SBU40-3 4" 3/4" 3
SLOTTING CUTTER ARBORS
CARBIDE INSERTS Includes B5 Bearing for 1/2" depth of cut.
INDEXABLE - 4 CUTTING EDGES
Slotting Cutter Arbors with B5 bearing are for use with the slotting cutters.
PART
NUMBER DESCRIPTION SIZE With the B5 bearing and slot cutter installed, the combo will achieve a 1/2" depth of cut.
SB-Insert 10 Pc. Insert Pak 14 mm x 14mm x 2mm PART SHANK OVERALL
SB Screw Replacement Insert Screw M5x7 NUMBER SIZE LENGTH
SB Wrench Insert Wrench T-15 Torx A200B 1/4" 2 3/8"
A205B 3/8" 2 3/8"
A210B 1/2" 2 3/8"
A220B 1/2" 4"
STEEL ROUTER Note - A220B has an extra long shank for extended reach.
COLLETS Reducer Bushings All include B5 Bearing for 1/2" depth of cut.
Steel Router Collets are reducer bushings for common 3/4" or 1/2" router collets that allow for Use B20 Bearing for 9/16" depth of cut.
decreasing bit size to 3/8", 5/16", 8mm, or 1/4". Use B25 Bearing for 3/8" depth of cut.
Use B26 Bearing for 1/4" depth of cut.
PART I.D. O.D. OVERALL Use B27 Bearing for 5/8" depth of cut.
NUMBER LENGTH
6400 1/4" 1/2" 1 1/4"
6400x8
6401
8mm
5/16"
1/2"
1/2"
1 1/4"
1 1/4"
DRAWER SLOT CUTTERS
6402 3/8" 1/2" 1 1/4" (Jemco Machines)
6403 1/4" 3/4" 1 1/4" Drawer Slot Cutters are for use with and replacements for drawer slot cutter
6404 5/16" 3/4" 1 1/4" arbors and Jemco Machines and come with 4 or 6 Carbide tipped wings.
6405 3/8" 3/4" 1 1/4"
6406 1/2" 3/4" 1 1/4" PART CUTTING BORE KERF NO.
NUMBER DIAMETER FLUTES
6800 1 1/4" 3/8"-24thd 3/16" 4
6801 1 1/4" 3/8"-24thd 3/16" 6
6804 1 1/4" 3/8"-24thd 1/4" 4
6805 1 1/4" 3/8"-24thd 1/4" 6
POLISHED SOLID CARBIDE KNIVES
Polished Solid Carbide Knives are designed to replace standard steel or cheaper carbide planer or
jointer knives in industry common machine sizes. These are made of the same high quality carbide
that all of our router bits are.
PART SIZE
NUMBER DRAWER SLOT CUTTER ARBORS
6902 1/8" x 5/8" x 4" PART SHANK OVERALL THREAD
6904 1/8" x 5/8" x 6" NUMBER DIAMETER LENGTH
6906 1/8" x 5/8" x 8"
6890 1/4" 2" 3/8"-24
6910 1/8" x 3/4" x 4"
6891 3/8" 2" 3/8"-24
6912 1/8" x 3/4" x 6"
6892 1/2" 2" 3/8"-24
6914 1/8" x 3/4" x 8"
6896 3/8" 3 1/4" 3/8"-24
Sold Individually

ROUTER BITS 34 Call Toll Free 800-645-5555

 DOWEL DRILLS • BORING BITS
LH HINGE BORING BITS
Carbide Tipped 10 mm
RH Shank - Import
Hinge Boring Bits are used with hinge boring machines
bore specific hinge cup sizes. Carbide Tipped PART #DH35-57
10 mm Shank - Import
DOWEL DRILLS Carbide Tipped & Solid Carbide CUTTING
DIAMETER
57MM OAL
PART #
70MM OAL
PART #
Dowel Drills (brad point & V point) are made for production use in line boring, hinge boring, and MM 10 MM Shank
dowel drilling machines. They are available in solid carbide, carbide tipped, and in left or right hand 15 DH 15-57 (LH) DH 15-70 (LH)
configurations. Available with a “brad point" style tip or a thru hole V-point. 20 DH 20-57 (LH) DH 20-70 (LH)
BRAD POINT (RH + LH) 25 DH 25-57 (LH) DH 25-70 (LH)
30 DH 30-57 (LH) DH 30-70 (LH)
CUTTING 57MM OAL 70MM OAL
35 DH 35-57 (LH) DH 35-70 (LH)
DIAMETER PART # PART #
Inch 10 MM Shank - Inch Sizes RH and LH rotation. Include LH suffix for left hand rotation. Supplied with flat on shank.
3/16" DB187-57 (LH) DB187-70 (LH)
7/32" DB218-57 (LH) DB218-70 (LH)
1/4" DB250-57 (LH) DB250-70 (LH) BORING BITS
3/8" DB375-70 (LH) KLINGSPOR’s Carbide Tipped Boring Bits feature a
7/16" DB437-70 (LH) centering point and two carbide spurs to eliminate tear out. The 2 1/8" diameter
1/2" DB500-70 (LH) bit is used mostly for door knob holes. The 35mm diameter bit is widely
MM 10 MM Shank - Metric Sizes used for European style cabinet door hinges.
*3 DB3-57 (LH) SC DB3-70 (LH) SC
4 DB4-57 (LH) (SC) DB4-70 (LH) (SC) PART CUTTING SHANK OVERALL
5 DB5-57 (LH) (SC) DB5-70 (LH) (SC) NUMBER DIAMETER DIAMETER LENGTH
6 DB6-57 (LH) (SC) DB6-70 (LH) (SC)
7 DB7-57 (LH) DB7-70 (LH) 8122125 2 1/8" 1/2" 6 1/8"
8 DB8-57 (LH) (SC) DB8-70 (LH) (SC) 6140 35mm 3/8" 2 3/8"
9 DB9-57 (LH) DB9-70 (LH) ** Use only in drill press or boring machine. NOT for use in routers.
10 DB10-57 (LH) DB10-70 (LH)
11 DB11-57 (LH) DB11-70 (LH)
12 DB12-57 (LH) DB12-70 (LH)
13 DB13-57 (LH) DB13-70 (LH)
14 DB14-57 (LH) DB14-70 (LH) FACE FRAME COUNTERBORES
15 DB15-57 (LH) DB15-70 (LH) Carbide Tipped Face Frame Counterbores are KLINGSPOR’s answer to the “cheap" pocket
16 DB16-57 (LH) DB16-70 (LH) hole bit replacements. These are designed to work with industry standard machines have replaceable
RH and LH rotation. Include LH suffix for left hand rotation. pilots and counterbores. See notes below.
Supplied with flat on shank.
Include SC suffix for optional Solid Carbide as available. PART COUNTER BORE PILOT
*3 mm available in Solid Carbide only. NUMBER DIAMETER DIAMETER LENGTH TYPE
3/8" SHANK
FF301 3/8" .136 4" Standard
FF301SP 3/8" .136 4" Spiral Flute
FF302 3/8" .136 6" Long
THRU HOLE V-POINT (RH + LH) FF303 Replacement .136 Pilot Fishtail Drill Bit (HSS)
CUTTING 57MM OAL 70MM OAL FF304 Replacement Set Screw Uses 5/64 Hex Key
DIAMETER PART # PART #
Inch 10 MM Shank - Inch Sizes
3/16" DT187-70 (LH)
7/32" DT218-70 (LH) Castle Machines/Porter-Cable
1/4" DT250-57 (LH) DT250-70 (LH) CM-DB 9/64" Pilot
3/8" DT375-70 (LH) CM-RU 3/8" Pocket
7/16" DT437-70 (LH) * RU4000H 3/8" Pocket
1/2" DT500-70 (LH)
Standard Type fits Unique, Norfield, Evans, Ritter, and Marcon face frame boring
MM 10 MM Shank - Metric Sizes machines. Long Version is for use on drill press. * Super High Quality
*3 DT3-57 (LH) SC DT3-70 (LH) SC
4 DT4-57 (LH) (SC) DT4-70 (LH) (SC)
5 DT5-57 (LH) (SC) DT5-70 (LH) (SC)
6 DT6-57 (LH) (SC) DT6-70 (LH) (SC)
7 DT7-57 (LH) DT7-70 (LH)
8 DT8-57 (LH) (SC) DT8-70 (LH) (SC) PART #SC100 PART #SC102
9 DT9-57 (LH) DT9-70 (LH)
10 DT10-57 (LH) DT10-70 (LH) SCREW SLOT BITS
11 DT11-57 (LH) DT11-70 (LH) Use these solid carbide bits with a plunge router to cut slots for #8 screws. Screw slots allow for the
12 DT12-57 (LH) DT12-70 (LH) seasonal movement of larger wooden parts such as table tops. These bits will also cut up to a 7/16"
13 DT13-57 (LH) DT13-70 (LH)
14 DT14-57 (LH) DT14-70 (LH) deep recess for the screw head.
15 DT15-57 (LH) DT15-70 (LH) PART RADIUS CUTTING SHANK OVERALL
NUMBER LENGTH DIAMETER LENGTH
RH and LH rotation. Include LH suffix for left hand rotation.
Supplied with flat on shank. 1/2" SHANK
Include SC suffix for optional Solid Carbide as available.
*3 mm available in Solid Carbide only.
SC100 82° C’sink 7/16" 15/16" 3"
SC102 Flat C’bore 1/2" 15/16" 3"

Visit us online: www.klingspor.com 35 ROUTER BITS

 ACCESSORIES

PART #9750

9750 - EXTENSION ADAPTER

For CNC Carving Machines
9500 - SOLID BRASS INLAY KIT Used for light routing and veining on CNC carving machines. Allows deeper reach. Adapter is
KLINGSPOR’s brass inlay kit allows you to make perfect fitting inlays for decoration or repairs. 1/2" shank. Accepts 1/4" shank bits only. Order Part #9750.
Simply cut your template from 1/4" thick material and trace it with your router to cut both the
cavity in your workpiece and the matching inlay to be inserted. Instructions are included. Our
kit includes a special centering pin to insure exact alignment with router spindle. Also includes
a 1/8" Solid Carbide Spiral Router Bit (Part# RD1600).

BRASS SET-UP GAUGE BLOCKS

Our Square Gauge Blocks are a quick way to make many easy, accurate set-ups. A great way
to make exact depth movements on plunge routers. On table routers, they’re perfect for setting
distances from the fence to the cutter, or for checking the bit height above the table. Supplied
9510 - BASE PLATE REDUCERS - SOLID BRASS in 1/8", 3/16", 1/4", 3/8", and 1/2" squares. Blocks can be "stacked" to cover a wider range of
These solid brass inserts fit into your router base plate to reduce the gap around the router bit. sizes. A very helpful tool!
Not only is this safer, but it also reduces tearout and helps support smaller workpieces. Supplied
in a set with openings of 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", and 1", plus retaining nut. Openings PART# DESCRIPTION
are slightly oversize for tool clearance. Fits any router with a standard 1 3/16" diameter recessed 9800 5 pc. Set - 2 1/2" Long
9810 5 pc. Set - 4" Long
hole for template guides.

QUICK CHANGE CHUCKS

Swap router bits quickly and easily. Cam-lock design clamps and loosens
with a partial turn using a hex key wrench. Much simpler than the
9600 - original two wrench method. Holds 1/2" shank bits. Order #6400 Router
SQUARE CORNER CHISEL Collet for 1/4" shanks. Replace the factory collet with a Quick Change.
Use this tool to square up the round corners left behind when routing
hinge mortises. Hold unit in mortise corner and strike with hammer.
PART DESCRIPTION
Our chisel features a sharp 3/8" square hardened steel cutting blade.
NUMBER
9700 All 1/2" Porter-Cable (except #100)
9710 All 1/2" Bosch
9720 Dewalt 625/Elu 1/2"/Fein/Festool/Freud
9730 Dewalt 616, 618, 621

ROUTER BITS 36 Call Toll Free 800-645-5555

 BEARINGS
ARBORS

Arbor Length

PART SHANK ARBOR ARBOR OVERALL

W300 - SHIM WASHER KIT
NUMBER DIAMETER DIAMETER LENGTH LENGTH
Use these shim washers to fine adjust the spacing on any arbor or assembly with a 5/16" diameter arbor
A200 1/4" 5/16" 7/8" 2 3/8" (Slot Cutters, Stile & Rail, Window Sash, Tongue & Groove). Washers are 5/16" I.D. x 1/2" O.D. Includes
A205 3/8" 5/16" 7/8" 2 1/2" three each of the following thicknesses: .004, .006, .008, .010, .012.
A210 1/2" 5/16" 7/8" 2 5/8"
A220 1/2" 5/16" 7/8" 4"
A250 1/4" 5/16" 1 3/16" 2 3/4"
A260 1/2" 5/16" 1 3/16" 2 7/8"
A300 1/4" 5/16" 1 7/16" 3"
A310 1/2" 5/16" 1 7/16" 3
3/16"
A375 1/2" 5/16" 1 3/4" 3 3/8"
A550 1/2" 1/2" 1 7/8" 3 7/8"

Arbors include nut and washer.

BALL BEARINGS BB501 - 5 PIECE BEARING CONVERSION KIT

PART OUTSIDE INSIDE
NUMBER DIAMETER DIAMETER APPLICATION
B1A 1/4" 1/8"
B1 3/8" 1/8"
B2 3/8" 3/16"
B3 1/2" 3/16" Standard Use this kit to vary the horizontal cutting depth of router bits with bearing pilots.
B3BLK 1/2" 3/16" 100 pcs. bulk
B3S 1/2" 3/16" Non-Mar Nylon Sleeve Great for stepping in to finish depth by controlled increments.
B3SQ 1/2" 3/16" Euro-Square (Pg. 15) Contains B2 (3/8"), B3 (1/2"), B7 (5/8"), B8 (3/4") Bearings and 3/32" Hex Key Wrench
B3T 1/2" 3/16" Tefl on® Shields
B3U .490" 3/16" for resharps (undersize)
B4 3/4" 1/4"
B5
B6
7/8" 5/16"
5/8" 1/4" BB600 - GENERAL BEARING REPAIR KIT
B7 5/8" 3/16"
B8 3/4" 3/16" This handy kit inludes spare bearings, screws, and wrench
B8SQ 3/4" 3/16" Euro-Square (Pg. 15) to replace bearings on most bits.
B9 1/2" 1/4" Includes five B3 (1/2 x 3/16) and two B2 (3/8 x 3/16) bearings, ten 54025S Screws, and a
B9U .490" 1/4" for resharps (undersize)
B11 1 1/8" 1/2" 3/32 Hex Key Wrench.
B12 7/8" 3/8"
B13 7/8" 1/2"
B14 11/16" 3/16"
B15 13/16" 3/16"
B16 1 1/4" 1/2"
B17 1 3/8" 1/2" BB701 - ACCESSORY KIT
B18 1 1/2" 1/2"
B19 3/4" 1/2" Great for replacement bearings and screws - Plus this generous bearing assortment allows you to
B20 3/4" 5/16"
B21 7/8" 1/4"
vary your cutting depths and change your profiles. Also contains lock collars and bearings for adding
B24 1 7/8" 1/2" bearing guides to the shanks of your standard bits for following templates.
B25 1 1/8" 5/16"
B26 1 3/8" 5/16"
B27 5/8" 5/16"
Contains: 12 bearings - four B3 (1/2 x 3/16), one each of B2 (3/8 x 3/16), B7 (5/8 x 3/16), B8 (3/4
B28 7/8" 3/16" x 3/16), B9 (1/2x 1/4), B6 (5/8 x 1/4), B4 (3/4 x 1/4), B5 (7/8 x 5/16) and B11 (1 1/8 x 1/2); two
B29 1" 3/16" each 1/4" lock collars (LC-1/4) and 1/2" lock collars (LC-1/2); one each 1/16, 5/64, 3/32 and 5/32
B33 9/16" 3/16"
BB300 7/8" x 10° 3/16" Non-Mar Nylon Sleeve
Hex Key wrenches; plus ten 54025S bearing screws.
1955T 1/2" 3/16" Sleeve for B11
BB315 7/8" X 15° 3/16"
BB318 7/8" X 18° 3/16"

Visit us online: www.klingspor.com 37 ROUTER BITS

 HEX KEY WRENCHES

BEARING LOCK COLLARS

Retaining Collars used when bearings are added to the shanks of router bits for following
templates. PART
NUMBER SIZE APPLICATION
HK-1/16 1/16" Bearing Lock Collars
PART SHANK OUTSIDE
HK-5/64 5/64" 1/8" I.D. Bearings (3-48 Screw)
NUMBER DIAMETER DIAMETER
LC-1/4 1/4" 7/16" * HK-3/32 3/32" 3/16" I.D. Bearings (5-40 Screw)
LC-1/2 1/2" 11/16" HK-5/32 5/32" 1/4" I.D. Bearings (10-32 Screw)

Uses part # HK-1/16 Hex Key Wrench * Standard Size for Most Bits
#LCS-Replacement Set Screw for Lock Collars

SPARE PARTS LISTING

Socket Head Cap Screws - 10 pc. pack

PART THREAD THREAD HEX KEY
NUMBER SIZE LENGTH SIZE
Flat Washers - 10 pc. pack
PART INSIDE OUTSIDE
34825S 3-48 1/4" 5/64"
NUMBER DIAMETER DIAMETER THICKNESS
54025S 5-40 1/4" 3/32"
31250W 5/16" 1/2" 1/16"
103238S 10-32 3/8" 5/32"
Add BLK to part number for 100 pcs.
Replacement Parts By Tool Number
Replacement Bearing sizes are listed in the catalog with each tool.
Most tools with bearing pilots on the end require only the 54025S
Screw. Exceptions:
Hex Nuts - 10 pc. pack
PART THREAD THREAD HEX KEY 34825S Screw: 2400,2401,2404A
NUMBER SIZE LENGTH SIZE 103238S Screw 2013-2016, 2410, 2415, 2560, 2570,
2575, 2580, 2715, 2900-2908, 3390
1032N 10-32 1/4" 3/8" 1032N Nut RFT5125, RFTD5125, RFT5200
31224N 5/16-24 1/4" 1/2" RFTD5200, UDFT5152

ROUTER BITS 38 Call Toll Free 800-645-5555

 ROUTER BIT SETS

Set 401 - BASIC 7 Pc. Bit Set - 1/2" Shank

Set 402 - BASIC 7 Pc. Bit Set - 1/4" Shank Set 502 - ROUNDOVER & BEADING - 1/4" Shank
This is the set pictured on the back cover. It’s made up of only the most popular woodworking Easily round off all your square edges with lightweight 1/4" capacity Hand Routers.
bits. Includes our 1/4" Straight, 1/2" Straight, R3/8 Roundover, 3/8" x 1/2" Rabbet, R3/8 Cove, Keep the whole range of sizes (R1/8, R3/16, R1/4, R3/8, R1/2) neatly organized and right
45° Chamfer, and 1/2" Flush Trim. at your fingertips. As with the 1/2" shank set, this kit comes fully equipped to extend
its usage by converting to Beading - i.e., Roundover with a decorative step.

Set 600 - STRAIGHT & HALF ROUND COMBO - 1/2" Shank

A nice collection of Straight Bits and Half Rounds grouped together in one protective case. This set
Set 470 - 3 PC. UNDERSIZED PLYWOOD includes:
DADO ROUTER BIT SET - 1/2" SHANK • 3/8 Straight • 3/8 Half Round • 5/8 Straight • 5/8 Half Round
These 3 “go-to" router bits are sized to exactly match today’s nominal plywood thicknesses. • 1/2 Straight • 1/2 Half Round • 3/4 Straight • 3/4 Half Round
Make everything fit just right while saving over buying bits separately! This handy group covers the full assortment of bits needed for the INCRA® HingeCrafter. KLINGSPOR
Industrial Quality.

Set 703 - 3 PIECE BALLNOSE

Includes:
SC66, RU1800RN, RU2075RN

Set 501 - ROUNDOVER & BEADING - 1/2"

Shank Roundovers are by far the most used Edge forming bits in woodworking. This set offers the most
common Radii (R1/4, R3/8, R1/2) in 1/2" shanks, plus a hefty 3/4" Radius workhorse. Extra bearings Set 705 - 5 PIECE CNC
and wrench are included to convert each bit from Rounding over to Beading - i.e., Roundover with a STARTER SET
decorative step.
Includes:
SC64, SC66, RU2075,1502, 1550

Also See Our Dovetail Sets on Page 32.

Visit us online: www.klingspor.com 39 ROUTER BITS

 ROUTER BIT REFERENCE
Chip Load, RPM, & Feed Rates:
Chip load is crucial when determining feed rates and other factors for spiral and straight router bits in a CNC application. It can literally make or “BREAK" a
router bit. Chip load is a measurement of the material thickness removed by each of the cutting edges while in a cut.

Actual feed rates will vary depending on machine horsepower, spindle quality, material being milled, rigidity of the clamps / hold down, etc. Faster rpm’s
will result in a cleaner cut, but will contribute to quicker wear due to heat and friction. Select the slowest RPM possible for each cutter. Start at a slower
feed rate and rpm than the maximum and work up until the combination of desired production and cut is accomplished. The following information is to be
used as a recommended starting point only when setting up for your application. Adjustments may still be required to achieve your desired needs based on
material being milled. This information does not guarantee specific results and tool or material damage may still occur.

Chip Load
Tool Dia. 2 flute 3 flute Cutting Diameter Max RPM Recommended
Upcut Up to 1/4" 24,000 18,000 - 21,000
1/8" to 3/16" .004 to .006 5/16" to 1" 21,000 18,000
7/32" to 5/16" .007 to .009 1" to 2-1/4" 18,000 16,000
3/8" to 1/2" .008 to .012 .006 to .010
2-1/4" to 2-3/4" 16,000 14,000
5/8" to 3/4" .010 to .014 .008 to .012
3" to 3-3/4" 12,000 10,000

Down Cut
Tool Dia. 2 flute 3 flute
1/8" to 3/16" .003 to .005
7/32" to 5/16" .006 to .008 How to figure feed rate
3/8" to 1/2" .007 to .011 .006 to .010 First, find the recommended speed range for your particular bit.
5/8" to 3/4" .010 to .014 .008 to .012 Then, find the ideal chip load by locating the proper bit and flute
combination in the chart.
Compression 2+2 3+3
1/4" .012 to .015 To figure out the required feed rate, use the following formula:
3/8" to 1/2" .016 to .022 .013 to .018 Feed Rate (inch per minute – ipm) = RPM x # of flutes x Chip
3/4" .022 to .025 load.
for 1+1 compression reduce chip load by 25%
Example:
Carbide Tipped If you want the feed rate for a 1/2" 2 flute compression bit do the
and Solid Carbide Straight Flute Tools following:
18,000 X 2 x .020 = 720ipm feed rate
1/4" to 5/16" .003 to .004
3/8" to 1/2" .006 to .009 * Feed rates are for depth of cut = cut diameter
3/4" to 1" .008 to .011 • If depth of cut is 2x cut diameter reduce chipload 25%
• Not recommended for 3x diameter at one pass
-1/8" to 2" .012 to .015

ROUTER BITS 40 Call Toll Free 800-645-5555

 DOOR-LITE BIT
Single Flute - Up/Down

Designed for Metal Clad Doors

THE SECRET
Traditional downcut spiral door bits on the market “BLOW OUT" material on the
bottom side of the door after the bit dulls. KLINGSPOR’s Up/Down Door-Lite bit
continues to perform after dulling because the material is “pulled" up instead of
being pushed down. The bits are made with high grade American tool steel and
precision ground on state of the art CNC grinders.

ASTOUNDING RESULTS
Tests were conducted of the KLINGSPOR Up/Down Door-Lite Bit against tradi-
tional downcut spiral door bits. Test cuts were performed on a CNC door cut-
ting machine routing steel clad exterior doors. The traditional bit cut an average
of 12,000 inches per bit, whereas the KLINGSPOR Door-Lite bit cut an amazing
22,000 inches! * Ideal operating specifications: 3,500 rpm @ 400 ipm

DOOR-LITE BIT
(Coated High Speed Steel Single Flute Up/Down Cut)
PART# CED CEL SHANK DIA OAL
HC 5250 1/2" 2 1/2" 1/2" 5 1/2"

HCF 5250 With Flat on Shank

DOOR-LITE BIT - WOOD & FIBERGLASS DOORS

(Solid Carbide Compression)
PART# CED CEL SHANK DIA OAL
UD5222 1/2" 2 1/4" 1/2" 5 1/2"

Visit us online: www.klingspor.com 41 ROUTER BITS

 NEW ITEM SPOTLIGHT

ULTIMATE COMPRESSION - SHEET GOODS

UD5050 3/8" CD X 1/2" CL X 1/2" SHANK X 3 OAL
UD5075 3/8" CD X 3/4" CL X 1/2" SHANK X 3 OAL

KROMA COMPRESSION
UD4122M-K 3/8" CD X 1-1/4" CL X 1/2" SHANK X 3 OAL
UD5122M-K 1/2" CD X 1-1/4" CL X 1/2" SHANK X 3 OAL

WOOD/FIBERGLASS DOOR-LITE
UD5222 1/2" CD X 2-1/4" CL X 1/2" SHANK X 5-1/2" OAL

DID YOU KNOW THAT KLINGSPOR

ALSO HAS SAW BLADES?!
SPOIL BOARD KLINGSPOR Carbide tipped saw blades are 100%
manufactured in Germany to the highest standards.
6220 2" CD X 1/2" CL X 1/2" SHANK They are laser cut from virgin German steel and
precision flattened, ground, and tensioned for balanced
cutting. They offer large European carbide tips to
ensure clean cuts and superior life. KLINGSPOR
industrial blades are computer-controlled and

SMALL RABBET BITS monitored with extremely tight tolerances

for incredible performance.
DE
IN GERM
AN
MA

1880 7/8" CD X 1/2" CL X 1/4" SHANK

1885 7/8" CD X 5/8" CL X 1/2" SHANK CH
HE

NI
A

O EN
ALE MA

ROUTER BITS 42 Call Toll Free 800-645-5555

 TABLE OF CONTENTS
SIGN MAKING CNC Roman Ogee ...................................... 15 Fine Finger Joint................................. 25
Ballnose Spiral ......................................3 Chamfer ............................................... 15 Multi-Side Bits..................................... 25
V Groove..................................................3 Edge Bevel .......................................... 15 Edge Band Bits.................................... 25
Carving Liner..........................................3 FLUSH TRIM BITS GROOVE PROFILING
Round Nose............................................3 Solid Carbide Spiral Flush Trims......4 Round Nose .....................................3,11
O-Flute Spirals.......................................3 Double Flute Flush Trim .................. 16 V-Groove ...........................................3,12
SOLID CARBIDE SPIRALS Double Bearing Flush Trim............. 16 Plunge Roundovers ......................... 14
Up Cut ......................................................4 V-Groove Flush Trim......................... 16 Plunge Ogee ...................................... 26
Down Cut................................................4 Overhang Trim.................................... 16 Classic Round Bottom ..................... 26
Chipbreaker............................................4 Three Flute Flush Trim ..................... 16 Classical Flat Bottom ....................... 26
Flush Trim Spirals .................................4 Downshear Flush Trim..................... 16 CABINET MAKING
Three Flute .............................................5 Combination Flush Trim ................. 16 MDF Door Bits .................................... 27
Left Hand ................................................5 LAMINATE TRIM BITS Stile & Rail ............................................ 28
Roughing (Hoggers)............................5 Solid Carbide Trimmers ...............7,17 Raised Panel ................................ 29, 30
Slow Spiral...............................................5 Ball Bearing Trimmers ..................... 17 Panel Back Cutter............................... 30
Up/Down (Compression) ..................5 Combination Flush or Bevel.......... 17 Vertical Panel Bits ............................. 30
SOLID CARBIDE Square Bearing Laminate Trimmers .......17 Door/Drawer Edge ........................... 31
Straight Bits............................................6 Trim-N-File Laminate Trimmers.... 17 Drawer Pull ......................................... 31
Fiberglass................................................6 SOLID SURFACE BITS WINDOW BITS
Solid Carbide Straight Bits................6 Round Over ....................................... 18 Window Sill Edge............................... 31
CNC Straight Bits .................................6 Round Under ..................................... 18 Window Sash...................................... 32
Flush Laminate Trim............................7 Face Inlay ............................................ 18 DOVETAILS ......................................... 32,33
7° Laminate Trim...................................7 Round Over Undermount ............. 18 CNC SPOILBOARD SURFACING........ 34
Hole & Flush Trim .................................7 Bevel Undermount Bowl ................ 18 SLOTTING
Rip & Slotting ........................................7 Overhang Bowl Trim ........................ 18 Slotting Cutters/Arbors ................. 34
Veining ....................................................7 PROFILE BITS Drawer Slot Cutters/Arbors............ 34
Screw Slot Bits.................................... 35 Template Bits ...................................... 19 Slotting & Rabbeting ....................... 13
STRAIGHT BITS Keyhole ................................................ 19 T-Slot ..................................................... 19
Left Hand ................................................8 T-Slot ..................................................... 19 Slot & Undercut ................................. 19
Carbide Tipped Straight Bits......... 8,9 Undercut Bits ..................................... 19 DOWEL DRILLS........................................ 35
Dado Bits ................................................9 Classical Cove ..................................... 20 BORING BITS............................................. 35
Staggertooth ...................................... 10 Wavy Edge........................................... 20 ACCESSORIES
Up/Down Staggertooth.................. 10 Radius Flute Cutter .......................... 20 Router Collets...................................... 34
Mortise ................................................. 10 Full Bead............................................... 20 Solid Carbide Knives........................ 34
Helix Mortise Cutters/Arbor......... .10 Multi-Beading ................................... 20 Inlay Kit................................................. 36
Panel Bits.............................................. 12 Double Round ................................... 20 Base Plate Reducers ......................... 36
Staggertooth Panel .......................... 12 Cove & Bead ........................................ 21 Square Corner Chisel........................ 36
Flush Trims........................................... 16 Ogee Fillet .......................................... 21 Quick Change Chucks ..................... 36
Template Bits ...................................9,19 Ogee....................................................... 21 Extension Adapter ........................... 36
FORM TOOLS Classical Pattern ................................ 21 Set-Up Gauge Blocks ....................... 36
Bowl & Tray........................................... 11 Edge Beading .................................... 21 Arbors.................................................... 37
Round Nose ........................................ 11 French Traditional.............................. 21 Shim Washer Kit ................................ 37
Half Round .......................................... 11 French Provincial Molding ............ 22 Bearings................................................ 37
Hand Grip ............................................ 11 Table Top Edges ................................ 22 Spare Parts .......................................... 38
Oval Edge ............................................ 11 Handrail ............................................... 23 ROUTER BIT SETS .................................. 39
V-Groove ...........................................3,12 Specialty Molding ............................. 23 REFERENCE ............................................... 40
Point Cutting Round Over.............. 12 Classic Multi-Form............................. 23 DOOR-LITE BIT ........................................ 41
Cove........................................................ 12 GLUE JOINTS NEW ITEMS................................................ 42
Rabbeting .......................................... 13 Locking Drawer Glue Joint ............ 24 Ultimate Compression - Sheet Goods
Biscuit Joining.................................... 13 Standard Glue Joint.......................... 24 Wood/Fiberglass Door-Lite
Round Over ........................................ 14 45° Lock Miter .................................... 24 Kroma Compression
Beading ................................................ 14 Wedge Tongue & Groove ............... 24 Small Rabbet Bits
Plunge Roundover............................ 14 Straight Tongue & Groove ............. 24
Roundover & Edge Trim.................. 14 Vee Panel Tongue & Groove.......... 25
Double Round Over ......................... 15 Tongue & Groove Assembly.......... 25

Visit us online: www.klingspor.com 43 ROUTER BITS

2555 Tate Boulevard, S.E.
PO Box 2367
Hickory, North Carolina 28603-2367
Toll Free 800-645-5555
Corporate 828-322-3030
Toll Free Fax 800-524-6758
Fax 828-326-0296
www.klingspor.com

PUB190501RBG