Q7T4-FP71G LCD Monitor Service Guide

Alignment Procedure
1. Alignment procedure (for function adjustment)

A. Preparation:
1. Setup input timing ICL-605( 1280x1024@75Hz ), 32-Grays pattern.
2. Setup unit and keep it warm up at least 30 minutes.

B. Timing adjustment:
1. Enter factory setting area (press “ENTER”, “EXIT” and then press “SOFTPOWER”).
2. Check the settings to following values:
Contrast = 50
Brightness = 90
OSD time = 20
Color = Normal
Language = English
Then, turn off the monitor power.
3. Turn on power enter user area.

C. Color balance adjustment:

1. Enter factory setting area (press “ENTER”, “I-Key” and then press “SOFTPOWER”).
2. Setup input timing ICL-605(1280x1024@75Hz), 32-Gray pattern (pattern 48) .
3. Press “I-KEY”, and than OSD will show “White Balance” item and than press “ENTER” button
to do auto color.

1
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

D. Color adjustment:
1. Setup input timing ICL-605, white pattern .
2. Confirm auto color adjustment had already done.
3. Measure color temperature by Minolta CA-110 (or equivalent equipment).
4. Check the color temperature Bluish, Reddish & Normal. The color temperature specification
as follows:

White Balance X+- 0.283+(-) 0.03

(Bluish, 9300K set on OSD) Y+- 0.297+(-) 0.03
White Balance X+- 0. 326+(-) 0.03
(Reddish, 5800K set on OSD) Y+- 0. 342+(-) 0.03
White Balance X+- 0.313+(-) 0.03
(sRGB, 6500K set on OSD) Y+- 0. 329 +(-) 0.03

2
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure
5. Setup input timing , 32 -Gray pattern.
To check if there are any abnormal display problems of preset timing modes .
Check the following preset timings with General pattern:
No. Mode H V
1 720×400 @ 70Hz 31.468 70.8
2 640×480 @ 60Hz 31.469 59.940
3 640×480 @ 75Hz 37.500 75.000
4 800×600 @ 60Hz 37.879 60.317
5 800×600 @ 75Hz 46.875 75.000
6 1024×768 @ 60Hz 48.363 60.004
7 1024×768 @ 75Hz 60.023 75.029
8 1152x864 @ 75Hz 67.500 75.000
9 1280×1024 @ 60Hz 63.981 60.020
10 1280×1024 @ 75Hz 79.976 75.025

6. Checking if the picture is no good, reject this monitor.

7. To check the power consumption by disabling “burn-in mode” setting
8. To clear user data and program complete DDC data to monitor by IIC bus communication.

E. Writing EDID file:

1. Setup a PC with DDC card.
2. Connect PC to monitor with a D-sub signal cable.
3. Please refer to the C212 for the correct EDID file.
4. Runs the writing program to write the EDID file into EEPROM .
5. Read EEPROM data and confirm it to match with the C212 document definition.

F. Command definition :

PC Host will send 0x7C IIC slave address and then following 4 bytes command
I2C Send Command Byte1 Byte2 Byte3 Byte4 OK N.A. Remark
Write Contrast to MCU RAM CA 55 Data cksum √
Write Brightness to MCU RAM CA 56 Data cksum √ Write data to MCU RAM and
Write Red Gain to MCU RAM CA 57 Data cksum √ update the related register to
Write Green Gain to MCU RAM CA 58 Data cksum √ refresh the screen immediately.
Write Blue Gain to MCU RAM CA 59 Data cksum √ Don’t store data to EEPROM.
Read Contrast from MCU RAM C3 55 XX cksum √
Read Brightness from MCU RAM C3 56 XX cksum √
Read Red Gain from MCU RAM by color index C3 57 XX cksum √
Read Green Gain from MCU RAM by color
index C3 58 XX cksum √ Base on current color index to
Read Blue Gain from MCU RAM by color index C3 59 XX cksum √ read back the right gain value.
Write C1 (Bluish) R-Gain Data to EEPROM AA 3C Data cksum √
Write C1 (Bluish) G-Gain Data to EEPROM AA 3D Data cksum √
Write C1 (Bluish) B-Gain Data to EEPROM AA 3E Data cksum √
Write C2 (sRGB) R-Gain Data to EEPROM AA 4C Data cksum √
Write C2 (sRGB) G-Gain Data to EEPROM AA 4D Data cksum √
Write C2 (sRGB) B-Gain Data to EEPROM AA 4E Data cksum √

3
Confidential
Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure
Write C3 (Reddish) R-Gain Data to EEPROM AA 5C Data cksum √
Write C3 (Reddish) G-Gain Data to EEPROM AA 5D Data cksum √
Write C3 (Reddish) B-Gain Data to EEPROM AA 5E Data cksum √
Write User R-Gain Data to EEPROM AA 6C Data cksum √
Write User G-Gain Data to EEPROM AA 6D Data cksum √
Write User B-Gain Data to EEPROM AA 6E Data cksum √
Write Cx R-Gain Data to EEPROM AA 7C Data cksum √
Write Cx G-Gain Data to EEPROM AA 7D Data cksum √ Reserved for some model have
Write Cx B-Gain Data to EEPROM AA 7E Data cksum √ extra color temperature
Write Contrast to EEPROM AA 92 Data cksum √
Write Brightness to EEPROM AA 93 Data cksum √
1=C1/9300/Bluish,

2=C2/6500/sRGB/,

3=C3/5800/Reddish,

4=User, 5=Cx
Write C/T index to EEPROM AA 94 0~4 cksum √
Write OSD-Hpos to EEPROM AA 95 Data cksum √
Write OSD-Vpos to EEPROM AA 96 Data cksum √
0=DE, 1=EN, 2=ES, 3=FR,
4=IT, 5=JA, 6=繁中, 7=簡中
Write Language to EEPROM AA 97 0~7 cksum √ (Also Update MCU RAM)
Write EEPROM OSD Timer AA 98 Data cksum √
Write EEPROM Volume AA 99 Data cksum √
For model with Gamma curve
Write EEPROM Gamma index AA 9A Data cksum √ selection function
Write OSD Transparency to EEPROM AA 9E Data cksum √
Write OSD Rotation to EEPROM AA 9F Data cksum √
Read C1 (Bluish) R-Gain data from EEPROM A3 3C XX cksum √
Read C1 (Bluish) G-Gain data from EEPROM A3 3D XX cksum √
Read C1 (Bluish) B-Gain data from EEPROM A3 3E XX cksum √
Read C2 (sRGB) R-Gain data from EEPROM A3 4C XX cksum √
Read C2 (sRGB) G-Gain data from EEPROM A3 4D XX cksum √
Read C2 (sRGB) B-Gain data from EEPROM A3 4E XX cksum √
Read C3 (Reddish) R-Gain data from EEPROM A3 5C XX cksum √
Read C3 (Reddish) G-Gain data from EEPROM A3 5D XX cksum √
Read C3 (Reddish) B-Gain data from EEPROM A3 5E XX cksum √
Read User R-Gain data from EEPROM A3 6C XX cksum √
Read User G-Gain data from EEPROM A3 6D XX cksum √
Read User B-Gain data from EEPROM A3 6E XX cksum √
Read Cx R-Gain data from EEPROM A3 7C XX cksum √
Read Cx G-Gain data from EEPROM A3 7D XX cksum √ Reserved for some model have
Read Cx B-Gain data from EEPROM A3 7E XX cksum √ extra color temperature
Read Contrast from EEPROM A3 92 XX cksum √
Read Brightness from EEPROM A3 93 XX cksum √

4
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure
1=C1/9300/Bluish,

2=C2/6500/sRGB/,

3=C3/5800/Reddish,
Read C/T index from EEPROM A3 94 XX cksum √ 4=User, 5=Cx
Read OSD-Hpos EEPROM A3 95 XX cksum √
Read OSD-Vpos from EEPROM A3 96 XX cksum √
0=DE, 1=EN, 2=ES, 3=FR,
Read Language from EEPROM A3 97 XX cksum √ 4=IT, 5=JA, 6=繁中, 7=簡中
Read OSD Timer from EEPROM A3 98 XX cksum √
Read Volume from EEPROM A3 99 XX cksum √
For model with Gamma curve
Read Gamma index from EEPROM A3 9A XX cksum √ selection function
Read OSD Transparency from EEPROM A3 9E XX cksum √
Read OSD Rotation from EEPROM A3 9F XX cksum √
Change Color Temp. to C1/9300K/Bluish CC 01 XX cksum √
Change Color Temp. to C2/6500K/sRGB CC 02 XX cksum √
Change Color Temp. to C3/5800K/Reddish CC 03 XX cksum √ Change C/T immediately. And
Change Color Temp. to User CC 04 XX cksum √ store C/T index to EEPROM.
Change Color Temp. to Cx CC 05 XX cksum √ Reserved
Change Input Source to D-Sub CD 01 XX cksum √
Change Input Source to DVI CD 02 XX cksum √
On burn in mode CE 01 XX cksum √ Store data to EEPROM
XX* = Non “1” value
Off burn in mode CE XX* XX cksum √ Store data to EEPROM
Monitor is forced power saving CF 01 XX cksum √
Monitor wake up from power saving CF XX* XX cksum √ XX* = Non “1” value
User mode to factory mode 1A 5A XX cksum √
Auto Color (Offset1, Offset2, Gain) 1B 5A XX cksum √
For specified “Industry
Copy EDID Serial number to EEPROM 1C 5A XX cksum √ Customer” model.
Factory mode to User mode 1E 5A XX cksum √
Clear user mode and factory recall 1F 5A XX cksum √ Store data to EEPROM
Write EDID data to MCU DDC RAM 55 NA NA NA √ For MTV312 MCU type
Copy DDC RAM data to EEPROM BB NA NA NA √ For MTV312 MCU type
Drive WP pin to low to enable write DDC IC 55 NA NA NA √ For stand alone DDC IC
Drive WP pin to high to disenable write function BB NA NA NA √ For stand alone DDC IC

EEPROM Bank R/W (For Debug using only, not for Production Line Write EEPROM directly)
Read EEPROM Bank 0 B0 Address XX cksum √
Read EEPROM Bank 1 B1 Address XX cksum √
Read EEPROM Bank 2 B2 Address XX cksum √ (For 24C08 type)
Read EEPROM Bank 3 B3 Address XX cksum √ (For 24C08 type)
Write EEPROM Bank 0 B8 Address Data cksum √
Write EEPROM Bank 1 B9 Address Data cksum √
Write EEPROM Bank 2 BA Address Data cksum √ (For 24C08 type)
Write EEPROM Bank 3 BB Address Data cksum √ (For 24C08 type)

5
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure
Note A: Byte4 (cksum) = Byte1 + Byte2 + Byte3
Note B: Data = The value write to MCU or EEPROM
Note C: XX = don't care, any value (<=0xFF).

When PC Host sends 0x7D command to MCU, MCU must return as following (2 bytes)
Return Code R-Byte1 R-Byte2
Checksum error code FC AA
Normal return code the above Byte3 (/data) FC
If normal return code is exact FCh FC CF

6
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

4. Wire Dressing and assembling concern

Prepare 1 panel

Assembly panel and main BKT

7
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add 4 screw between panel and main BKT

8
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add FFC

9
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add Tape

10
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Assembly IF board and Power Board

11
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Assembly PCB module and main BKT

12
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Assembly IF board and FFC

13
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add one tape

14
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Assembly lamp wire and Power Board

15
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add one screw

16
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add 5 screw

17
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Assembly main shielding and main BKT

18
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add 2 screw

19
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Assembly control board wire and IF board

20
Confidential
Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

21
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add one tape

22
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Assembly Bezel and Rear Cover

23
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add 4 screw

24
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Add 1 screw

25
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Assembly Base and Rear cover

26
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

Finished

27
Confidential
Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

28
Confidential
Q7T4-FP71G LCD Monitor Service Guide
Alignment Procedure

29
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory
I. Introduction:
The Q7T4 is a 17” SXGA (1280x1024) , 16.2M colors(R, G, B 6-bit data+FRC data) TFT
LCD monitor. It’s an analog only interface LCD monitor with a 15 pins D-sub signal cable. it’s
compliant with VESA specification to offer a smart power management and power saving function. It
also offers OSD menu for users to control the adjustable items and get some information about this
monitor, and the best function is to offer users an easy method to set all adjustable items well just by
pressing one key, we called it “Auto key” which can auto adjusting all controlled items. Q7T4 also
offer DDC2 function to meet VESA standard.

II. Block diagram

The Q7T4 consists of a LCD module with 4 lamps, an power board, a control board ,and a
interface BD. The block diagram is shown as below.

LCD module with 4 lamps (backlight)

Inverter
Interface board

Power
Control board

D-Sub

AC power in

III. Circuit operation theory:

A-1.) Interface board diagram:

1
Confidential
Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory

MTV312M Clock
64(AJ) Generator

XGA
1280×1024
140MHz RTD 2023
LCM
D-SUB
ADC

IIC Keypad

(a) Circuit operation theory:

A basic operation theory for the interface board is to convert input signal into digital RGB .
Analog RGB signal is converted to digital signal through ADC. The microprocessor RTD2023
receives video data and optimizes the image automatically. It also supports 16 color from a 64k
palette bitmap OSD, and keypad controlling. The output data are sent to LCD module.

(b) IC introduction:
1.) DDC (Display Data Channel) function: We use DDC IC to support DDC/2B function. DDC
data is stored in 24C04(EEPROM). Those data related to LCD monitor specification. PC
can read them by “SDA” and “SCL” serial communication for I²C communication for
DDC2B.
2.) RTD2023 IC: There are triple ADC, LVDS transmitter ,Scaling, and OSD functions in the
RTD2023 IC. Scaling IC is revolutionary scaling engine, capable of expanding any source
resolution to a highly uniform and sharp image, combined with the critically proven
integrated 8 bit triple-ADC and patented Rapid-lock digital clock recovery system. It also

2
Confidential
Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory
support detect mode and DPMS control.
3.) MTV312M64: To stored the source code which is accessed by MCU to run program.
4.) EEPROM: We use 24C04 to store all the adjustable data and user settings.And use 24C02 to
store DVI EDID data.

A-2.) Control board introduction:

There are 6 keys for user's control which includes “Power”, “Enter”, “Up/Plus”,
“Down/Minus” , “Exit”, and “iKey” . The following descriptions are the introduction of these keys.
(1) Power key: to turn/off power of monitor
(2) “Enter” key: to enter sub-menus or select items.
(3) “Up/Plus key: to select previous and to increase adjustment
(4) “Down/Minus” key: to select next and to decrease adjustment
(5) “Exit” key: to back to previous menu, or leave OSD (auto save)
(6) “iKey”: to perform auto adjustment
(7) LED: It indicates the DPMS status of this LCD monitor; green light means DPMS on (Normal
operating condition). Amber light means DPMS off (Powersaving).

A-3.) Power board diagram:

EMI Filter Rectifier and Isolation power Rectifier and filter Inverter circuit

filter transformer

PWM controller Switching element Rectifier and filter

LDO regulator

Feedback Isolation

Fig.1

3
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory

#1 EMI Filter
This circuit (fig. 2) is designed to inhibit electrical and magnetic interference for meeting FCC, VDE,
VCCI standard requirements.

Fig. 2

#2 Rectifier and filter

AC Voltage (90-264V) is rectified and filtered by BD601, C605 (See Fig 3) and the DC Output
voltage is 1.4*(AC input). (See Fig.3)

Fig. 3

4
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory
#3 Switching element and Isolation power transformer
When the Q601 turns on, energy is stored in the transformer.
During Q601 turn-off period, the stored energy is delivered to the
secondary of transformer. R607, C607 and D601 is a snubber circuit.
R615 is current sense resistor to control output power. (See Fig.4)

Fig. 4
#4 Rectifier and filter
D701 and C703 are to produce DC output. L701 is used to suppress high Frequency switching spikes.
(See Fig.5)

Fig. 5

5
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory
#5 PWM Controller
The PWM controller NCP1200A implements a standard current mode architecture. With an
internal structure operating at a fixed 40KHz. Where the switch time is
dictated by the peak current set-point. When the current set-point falls
below a given value. The output power demand diminishes, the IC
automatically enters the so-called skip cycle mode and provides
excellent efficiency.

Fig. 6
#6 Feedback circuit
PC123 is a photo-coupler and TL431 is a shunt regulation. They are
used to detect the output voltage change and be the primary and
secondary isolation. When output voltage changes, the feedback voltage
will be compared and duty cycle will be decided to control the correct
output voltage. (See Fig.7)

6
Confidential
Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory

Fig. 7

A-3.) Control board introduction:

The main parts of the control board are a push button, and a LED.
(a) Push button: It’s a simple switch function, pressing it for “ON” to do the auto
adjustment function, releasing it for “OFF” to do nothing.
(c) LED: It indicates the DPMS status of this LCD monitor; green light means DPMS on
(Normal operating condition). Amber light means DPMS off (Power off condition).

7
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory
A-4.) Inverter diagram:
1.Block Diagram:

ON/OFF OSCILATOR TRANSFORMER CCFL

15Vin
switching CIRCUIT

ON/OFF PWM CONTROLLER

PROTECTION
TL1451 CIRCUIT
AND DETECT
BRT_ADJ

2. General Specification
Input Voltage: 15V
Input Current: 2A max.
ON/OFF Voltage: 5V
PWM Duty: 5V/50KHz
Output Requirement:
Max. Output Current: 7.5mA
Min. Output Current: 3.3mA
Lamp Working Voltage: 660Vrms
Open Lamp Voltage: 1500Vrms
Frequency: 50KHz

8
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory
3.Circuit Operation Theorem
3.1 ON/OFF SWITCH

The turn-on voltage was controlled by R815 and R816.The inverter was turned on or off by the
switching transistors Q801 and Q802.

9
Confidential
Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory
3.2 PWM Control circuit

TL1451 is a dual PWM controller.C807 and R811 decide the working frequency.BLT_ADJ signal is
from control board, control pulse width then decide how much energy delivery to CCFL also decide
CCFL brightness. Q810 and Q811 be the buffer to rise the drive capability and the totem poles
circuit can improve a capable of driving for Q812.C813 decide the striking time delay.

10
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Circuit Operation Theory
3.3 Oscillator Circuit

Royer circuit uses the characteristic of transformer saturation to oscillate. When the DC power inject,
Q808 or Q809 will turns on, and the current Ic increases. After a period, the transistor will leave the
saturation status and Vce increase. The result causes the voltage of primary coil get lower. Finally the
transistor turn off, and another transistor turn on. These statuses are repeated and the pin7 and pin8 of
T801 will get a sine wave to turn on CCFL.

11
Confidential
 5 4 3 2 1

D D
CON301 SW301 2240069431
1 I _KEY KEY_MENU 1 2
2
3 KEY_EXIT LED301 BLU/ORG
KEY_LEFT G1 G2
4
5 BLU BLU A2
6 ORG J SW302 2240069431
7 ORG A1 KEY_ RIGHT 1 2
8 KEY_ RIGHT
9 KEY_MENU
PW_SW G1 G2
10

2060089110 SW303 2240069431

KEY_LEFT 1 2

G1 G2

C SW306 2240069431 C
PW_SW 1 2

G1 G2

SW304 2240069431
KEY_EXIT 1 2

G1 G2

SW305 2240069431
I _KEY 1 2

G1 G2

B B

LED use 06.3N5YG.14X;

Key use 22.40069.431

Project Code Model Name OEM/ODM Model Name

99.L1C72.001 Q7T4 NA
Title
A
CTRL BOARD A

Size PCB P/N PCB Rev. Document Number R e v.

<Size> 99.L1C72.000-C3-304-002 0
48.L1C03.S02 S02

Date: Thursday, August 26, 2004 Sheet 1 of 1

Prepared By Reviewed By Approved By
ANGEL HU ALLEN PC LEE DAVEN WU
5 4 3 2 1
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification

Table of Contents

1. Introduction 3

2. Operational Specification 3
2.1 Power supply................................................................................................................................. 3
2.2 Signal interface ............................................................................................................................. 4
2.3 Video performance ........................................................................................................................ 5
2.4 Scan range ..................................................................................................................................... 6
2.5 Plug & Play DDC2B Support ....................................................................................................... 6
2.6 Support Timings ............................................................................................................................ 6

3. Operational & Functional Specification 7

3.1 Video performance ........................................................................................................................ 7
3.2 Brightness Adjustable Range ........................................................................................................ 7
3.3 Acoustical Noise ........................................................................................................................... 7
3.4 Environment.................................................................................................................................. 7
3.5 Transportation ............................................................................................................................... 7
3.6 Electrostatic Discharge Requirements........................................................................................... 8
3.7 EMC .............................................................................................................................................. 8
3.8 Reliability...................................................................................................................................... 8
3.9 Audio performance........................................................................................................................ 9

4. LCD Characteristics 9
4.1 The Physical definition & Technology summary of LCD panel ................................................... 9
4.2 Optical characteristics of LCD panel ............................................................................................ 9

5. User Controls 10
5.1 User’s hardware control definition................................................................................................ 10
5.2 OSD control function definition.................................................................................................... 10

6. Mechanical Characteristics 11
6.1 Dimension ..................................................................................................................................... 11
6.2 Weight ........................................................................................................................................... 11
6.3 Plastic ............................................................................................................................................ 11
6.4 Carton............................................................................................................................................ 12

1
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification

Table of Contents

7. Pallet & Shipment 12

7.1 Container Specification................................................................................................................. 12
7.2 Carton Specification...................................................................................................................... 12
Product: ................................................................................................................................. 12
Package: ................................................................................................................................ 12

8. Certification 12

Appendix: Physical Dimension Front View and Side view 14

2
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification

1. Introduction
This specification describes Q7T4, which is a 17.0” analog interface color TFT LCD monitor without audio. The
monitor supports up to 1280x1024 pixel resolution and refresh rate of 75 Hz. The independent 6 bits R, G, B
colors are capable of displaying 16.2M colors (RGB-6bit + FRC data). In addition, dithering function is
supported. The features summary is shown below,
*All panel spec. in C201 definition depends on the variance of panel source.
Feature items Specifications Remark
Further divided into v.0 and v.1
Panel supplier & module name AUO M170EG01
versions (spec v.1)
Screen diagonal 17.0” (432mm) 337.920(H) x 270.336(V)
Display Format SXGA / 1280 (H) x 1024 (V)
Pixel Pitch 0.264 mm x 0.264 mm
R/L: 70/70 degrees (typ.)
Viewing Angle (@ Contrast Ratio = 10) Panel spec.
and U/D: 70/60 degrees (typ.)
Analog interface with Scaling supported Yes With 15-pin D-sub connector
DVI interface with Scaling supported No
Video interface with Scaling supported No
Max resolution mode supported 1280 x 1024 @ 75Hz
Number of Display Colors supported 16.2M colors (RGB 6-bits + FRC data)
Contrast Ratio 450:1 (typ.)
White Luminance@CCFL
Luminance 260 cd/m2 (typ.)
7.5mA (center)
AC power input Yes 90-264 Volts, 47-63 Hz.
DC power input (with AC power adapter) No
≤ 1W at 115±5 VAC
DPMS supported Yes ≤2W at 230 VAC in Power off
Preferred Mode
LED indicator for power status showed Yes Green/Amber/Non
OSD for control & information supported Yes
Multi-language supported for OSD Yes 8 languages
6 buttons including 1 monitor
Buttons control supported Yes
power on/off control button.
Flywheel control supported No
Scaling function supported Yes
Auto adjustment function supported Yes “i-key” function
DDC function supported (EDID ver. 1.3) Yes DDC2B only
Audio speakers supported No
Audio Jack (input connector) supported No
Earphone Jack (input connector) supported No
Microphone function supported No
Mechanical Tilt base design Yes From -5 to +20 degree
VESA wall mounting design Yes
Mechanical Rotate design No
Mechanical Lift base design No
Kensington compatible lock design Yes

2. Operational Specification
2.1 Power supply

3
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification
Item Condition Spec OK N.A Remark
Input Voltage range Universal input full range 90~264VAC /47~63Hz √
Input Current range 90 ~ 264VAC < 2.0 Arms √
Power Consumption Normal “On” operation < 40 W √ LED: Green
< 1 W in power preferred
DPMS DPMS “Off” state mode, 115V √ LED: Amber
< 2 W, 230V
110 VAC < 30 A (peak)
Inrush Current √ Cold-start
220 VAC < 60 A (peak)
Earth Leakage Current 264 VAC/50Hz < 3.5 mA √
1. 1500VAC, 1 sec Without damage (on-line test)
Hi-Pot √
2. Ground test: 30A, 1sec < 0.1 ohm (in-lab test)
Power Line Transient IEC1000-4-4 1KV √
Common: 2KV,
IEC1000-4-5 (Surge)
Differential: 1KV √
Panel Spec.
CCFL operation range 90 ~ 264VAC 3 mA ~8mA √ 3.0 ~ 8.0mA rms
Panel Spec.
CCFL Frequency 90 ~ 264VAC 40KHz ~ 80KHz √ 40KHz ~ 80KHz
Color: Black
Power cord √
Length: 1500 +/- 50 mm

2.2 Signal interface

Item Condition Spec OK N.A Remark
15-pin D-Sub
Color: Black
√
Length: 1500 +/- 30 mm
Signal Cable
Color: Black
24-pin DVI-D
Length: 2000 +/- 50 mm
√
15-pin D-sub connector See Note-1 √ For 15-pin D-sub
Pin assignment
24-pin DVI-D connector See Note-2 √ For 24-pin DVI-D
Signal type Separate analog R/G/B √ For 15-pin D-sub
Video input Level 700 mV (peak to peak) √
Impedance 75 Ohms +/- 1.5 Ohms √
Separate H/V-sync
Signal type Composite H/V-sync √ For 15-pin D-sub
(Positive/Negative)
Logic High: 2.4V ~ 5.5V
Refer to VESA VSIS
Sync input Level Logic Low: 0V ~ 0.5V √ Standard V1R1
(TTL level)
Impedance Minimum 2.2KΩ(pull down) √ 10KΩ for application
Sync Pulse Width (SPW) 0.7μs < H-SPW √
1H < V-SPW

Note-1: The pin assignment of 15-pin D-sub connector is as below,

1 5

6 10

11 15

4
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification
Pin Signal Assignment Pin Signal Assignment
1 Red video 9 PC5V (+5 volt power)
2 Green video 10 Sync Ground
3 Blue video 11 Ground
4 Ground 12 SDA
5 Cable Detected 13 H-Sync (or H+V)
6 Red Ground 14 V-sync
7 Green Ground 15 SCL
8 Blue Ground

Note-2: The pin assignment of 24-pin DVI-D connector is as below,

Pin Signal Assignment Pin Signal Assignment

1 TMDS RX2- 13 Floating
2 TMDS RX2+ 14 +5V Power
3 TMDS Ground 15 Ground
4 Floating 16 Hot Plug Detect
5 Floating 17 TMDS RX0-
6 DDC Clock 18 TMDS RX0+
7 DDC Data 19 TMDS Ground
8 Floating 20 Floating
9 TMDS RX1- 21 Floating
10 TMDS RX1+ 22 TMDS Ground
11 TMDS Ground 23 TMDS Clock+
12 Floating 24 TMDS Clock-

2.3 Video performance

Item Condition Spec OK N.A Remark
Max. support Pixel rate 135 MHz √
Max. Resolution 1280 x 1024 √
< 6.25 ns
1280 x 1024 @ 75Hz
Rise time + Fall time (50% of minimum pixel √ (max. support timing)
clock period)
Settling Time after Refer to VESA VSIS
overshoot /undershoot
< 5% final full-scale value √ Standard V1R1
< 12% of step function Refer to VESA VSIS
Overshoot/Undershoot voltage level over the full √ Standard V1R1
voltage range

5
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification
2.4 Scan range
Item Condition Spec OK N.A Remark
Horizontal 30 ~ 83 KHz √
Vertical 56 ~ 76 Hz √ Without Frame buffer

2.5 Plug & Play DDC2B Support

Item Condition Spec OK N.A Remark
DDC channel type DDC2B √
Refer to Q7C4 S/W
spec. document to see
EDID Version 1.3 √ the detailed EDID data
definition.
2.6 Support Timings
Input Timing Actual Output

Resolution Horizontal Vertical Dot Clock Actual display OK N.A Remark

640x350 31.47(P) 70.08(N) 25.17 1280x943 √ DOS

720x400 31.47(N) 70.08(P) 28.32 1280x1024 √ DOS

640x480 31.47(N) 60.00(N) 25.18 1280x1024 √ DOS

640x480 35.00(N) 67.00(N) 30.24 1280x1024 √ Macintosh

640x480 37.86(N) 72.80(N) 31.5 1280x1024 √ VESA

640x480 37.50(N) 75.00(N) 31.5 1280x1024 √ VESA

800x600 37.88(P) 60.32(P) 40.00 1280x1024 √ VESA

800x600 48.08(P) 72.19(P) 50.00 1280x1024 √ VESA

800x600 46.86(P) 75.00(P) 49.50 1280x1024 √ VESA

832X624 49.72(N) 74.55(N) 57.29 1280x1024 √ Macintosh

1024x768 48.36(N) 60.00(N) 65.00 1280x1024 √ VESA

1024x768 56.48(N) 70.10(N) 75.00 1280x1024 √ VESA

1024x768 60.02(P) 75.00(P) 78.75 1280x1024 √ VESA

1024X768 60.24(N) 74.93(N) 80.00 1280x1024 √ Macintosh

1152x864 67.50(P) 75.00(P) 108.00 1280x1024 √ VESA

1152x870 68.68(N) 75.06(N) 100.00 1280x1024 √ Macintosh

1152x900 61.80(N) 66.00(N) 94.50 1280x1024 √ SUN 66

1152x900 71.81(N) 76.14(N) 108.00 1280x1024 √ SUN

1280x1024 64.00(P) 60.00(P) 108.00 1280x1024 √ VESA

1280x1024 75.83(N) 71.53(N) 128.00 1280x1024 √ IBM1

1280x1024 80.00(P) 75.00(P) 135.00 1280x1024 √ VESA

1280x1024 81.18(N) 76.16(N) 135.09 1280x1024 √ SPARC2

Note-3: “P”, “N” stands for “Positive”, “Negative” polarity of incoming H-sync/V-sync (input timing).

6
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification
3. Operational & Functional Specification
3.1 Video performance
Item Condition Spec OK N.A Remark
Any input resolution modes
Resolution
which are under 1280 x 1024
1280 x 1024 √
Contrast ratio 450:1 (typ.) √
Brightness At R/G/B saturated condition 2
260 cd/m (typ.) @ 7.5mA √
Response time Rising + Falling time 16 ms (typ.) √
At Contrast ratio = 10 R/L: 70/70 degrees (typ.) √
Viewing angle
At Contrast ratio = 10 U/D: 70/60 degrees (typ.) √
CIE coordinate of White (0.31, 0.33) +/- (0.03, 0.03) √
16.2M colors
Display colors
(RGB 6-bits + FRC data) √ Support dithering

3.2 Brightness Adjustable Range

Item Condition Spec OK N.A Remark
At default contrast level (Max. brightness value –
Brightness adjustable range (saturate point) & Full-white Min. brightness value) √
color pattern ≧ 100 cd/㎡

3.3 Acoustical Noise

Item Condition Spec OK N.A Remark
At 1 meter distance
Acoustical Noise ≦ 40 dB/A √
& “Audio” function disabled

3.4 Environment
Item Condition Spec OK N.A Remark
Operating 0 ~ +40 ℃ √
Temperature
Non-operating -20 ~ +60 ℃ √
Operating 10 ~ 90% √ Non-condensing
Humidity
Non-operating 5 ~ 95% √ Non-condensing
Operating 0~3048m (10,000ft) √ Without packing
Altitude
Non-operating 0~12,192m (40,000ft) √ With packing

3.5 Transportation
Item Condition Spec OK N.A Remark
(1) Sine wave
5~200Hz 1.5G, 1 octave/min,
15 min dwell on each resonant
(1) Vibration Package, Non-Operating frequency, all primary axis, √
one sweep (30 min minimum)
per orientation, total of 90+
min.

7
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification
(2) Random
5 ~100 Hz, 0 dB/Oct. 0.015
g2/Hz
100 ~200 Hz, -6 dB/Oct.
200 Hz, 0.0038 g2/Hz
Equivalent to 1.47 Grms, All
primary axis, 20 min per-
orientation, total is 60 min.
(3) Procedure:
Confirmed sample with
appearance and function ready
before testing then compare
with after test record as
brightness, uniformity and
contrast ratio. Perform
random vibration after
sine-wave vibration test.
Test Spectrum:
20 Hz 0.0185(g2/Hz)
200Hz 0.0185(g2/Hz)
(2) Unpackaged Vibration Unpackaged, Non-Operating Duration : 5 Minutes √
Axis : 3 axis ( Horizontal
and Vertical axis ,Z axis)
91 cm Height (MP stage)
(3) Drop Package, Non-Operating (1 corner, 3 edges, 6 faces) √
Waveform: half sine
Faces: 6 sides/ per orientation
Wooden package,
(4) Shock Non-Operating
3 shocks. √
Duration: <3ms
Velocity accelerate: 75g

3.6 Electrostatic Discharge Requirements

Item Condition Spec OK N.A Remark
Contact: 8KV
Electrostatic Discharge IEC801-2 standard
Air: 15KV √

3.7 EMC
Item Condition Spec OK N.A Remark
Band 1 < 10 V/m
Electric
Band 2 < 1 V/m √
TCO03
Band 1 < 200nT
Magnetic
Band 2 < 25nT √
FCC part 15J class B After Mass production under
1dBuv for constant measure.
EMI
Besides DNSF and VCCI
√
EN55022 class B
class-2 are optional.

3.8 Reliability
Item Condition Spec OK N.A Remark
MTBF Prediction Refer to MIL-217F > 60,000 Hours √ Excluding CCFL
CCFL Life time At 25±2℃, under 7.0mA 50,000 Hours (typ.) √ See Note-4
Note-4: CCFL lifetime is determined as the time at which brightness of lamp is 50%. The typical lifetime of
CCFL is on the condition at 7.5mA lamp current.

8
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification

3.9 Audio performance

Item Condition Spec OK N.A Remark
Preamp + Power amp
(1)Output power 1 Wrms/CH @ 1KHz √
(2)THD (@ 1W) <1% √
(3)S/N ratio >40dB √
Speaker Driver
(1)Nominal impedance 8 ohm √
(2)Rated input power 2 W/CH √
(3)Frequency response 180~20KHz SPL-10dB √
(4)Output sound pressure level 84 ± 3 dB (1W 0.5M) √
(5)Dimension of box 62x33cx20 mm2 √
Audio Control
(1)Volume range 0 ~100 levels √
(2)Mute On/Off √

4. LCD Characteristics
4.1 The Physical definition & Technology summary of LCD panel
Item Condition Spec OK N.A Remark
LCD Panel Supplier AUO √
Panel type of Supplier M170EG01 V1 √
Screen Diagonal 432mm(17.0”) √
Display area Unit=mm 337.920(H) x 270.336(V) √
Physical Size Unit=mm 358.5(H) x 296.5(V) x 17.0 (D) (typ.) √
Weight Unit=gram 1900 (typ.) √
Technology TN type √
Pixel pitch Unit=mm 0.264 x 0.264 √ Per one triad
Pixel arrangement R/G/B vertical stripe √
Display mode Normally white √
Support color 16.2M colors (RGB 6-bits + FRC data) √

4.2 Optical characteristics of LCD panel

Item Unit Conditions Min. Typ. Max. Remark
[degree] Horizontal (Right) 60 70 -
[degree] CR = 10 (Left) 60 70 -
Viewing Angle
[degree] Vertical (Up) 60 70 -
[degree] CR = 10 (Down) 50 60 -
Contrast ratio Normal Direction 250 450
[msec] Rising Time - 12 20
Response Time [msec] Falling Time - 4 5
[msec] Rising + Falling - 16 25
Color / Chromaticity Red x 0.61 0.64 0.67
Red y 0.31 0.34 0.37

9
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification
Green x 0.26 0.29 0.32
Coordinates (CIE)
Green y 0.58 0.61 0.64
Blue x 0.11 0.14 0.17
Blue y 0.04 0.07 0.10
White x 0.28 0.31 0.34
Color Coordinates (CIE) White
White y 0.30 0.33 0.36
Luminance Uniformity [%] 9 points measurement 75 80 -
White Luminance @ CCFL [cd/m2]
210 260 -
7.5mA (center)
Crosstalk (in 75Hz) [%] 1.5
* The test methods for the above items’ definition, please refer to the relative panel specification.

5. User Controls
5.1 User’s hardware control definition
Item Condition Spec OK N.A Remark
Monitor Power button √
Enter button √
Right/Inc. button √
Left/Dec. button √
Exit /Volume button √
I-key button √
Mode Selection button √
Mute button √
Input source select button √

5.2 OSD control function definition

Item Condition Spec OK N.A Remark
Auto Adjust Auto-Geometry √
Brightness √
Contrast √
Horizontal Position √
Vertical Position √
Pixel Clock √
Phase √
Bluish
Reddish
Color sRGB √
User: Separate R/G/B adjustment
OSD Horizontal position
OSD Position
OSD Vertical position √
OSD Time From 5 sec to 60 sec √
Language 8 languages √
Color recall
Recall
Recall All √
Mode Selection √

10
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification
D-sub
Input Select
DVI √
Sharpness √
Display Information For input timing √
Volume √
Mute √
Hot key for Brightness √
Hot key for Contrast √
Hot key for Volume √
Hot key for Mode √
* The detailed firmware functions’ specification, please refer to C212 S/W spec. document.

6. Mechanical Characteristics
6.1 Dimension
Item Condition Spec OK N.A Remark
Bezel opening 339.84 x 272.24 mm √
Monitor without Stand L x W x H mm 323.75*378*60.5mm √
Monitor with Stand L x W x H mm 362*378*135.31 mm √
Carton Box (outside) L x W x H mm 456(L)*423(W)*114(H) √
Tilt: -5 ~ +20 degree
Tilt and Swivel range √
Swivel: 0 degrees

6.2 Weight
Item Condition Spec OK N.A Remark
Monitor (Net) 3.8 Kg √
Monitor with packing (Gross) 5.7 Kg √

6.3 Plastic
Item Condition Spec OK N.A Remark
Flammability 94-HB √
Heat deflection To ABS 65 ℃ √
UV stability ABS Delta E < 8.0 √
MPRII: ABS
Resin √
(VW55/VE0856/D350)
Bezel texture
Texture MT-11020 √ MT-11000
Bezel painting
Color BCS-Y5003A √ T8020C

11
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification
6.4 Carton
Item Condition Spec OK N.A Remark
Color Kraft √
Material B Flute √
Compression strength 288 KGF √
Burst Strength 16 KGF/cm2 √
Stacked quantity 18 Layers √

7. Pallet & Shipment

7.1 Container Specification
Quantity of products Quantity of Products Quantity of pallet
Stowing Type Container (sets) (sets) (sets)
(Every container) (Every Pallet) (Every Container)
20' 1080 Pallet A: 90 Pallet A: 12
With pallet Pallet B: 72 Pallet B: 12
40' 2520 Pallet A: 90 Pallet A: 14
Pallet B: 72 Pallet B: 14
20' X X
X X
Without pallet
40' X X
X X
7.2 Carton Specification
Product:
Dimension w/o Base Dimension w/ Base
Net Weight (Kg) Gross Weight (Kg)
L*W*H (mm) L*W*H (mm)
3.8Kg 5.7Kg 323.75*378*60.5mm 362*378*135.31 mm

Package:
Carton Interior Dimension (mm) Carton External Dimension (mm)
L*W*H L*W*H
448(L)*415(W)*100(H) 456(L)*423(W)*114(H)

8. Certification
Item Condition Spec OK N.A Remark
ISO14000
Environment Green design API Doc. 715-C49 √ Requirement
Blue Angel German Standard √
E-2000 Switzerland √

12
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification
EPA USA Standard √
TCO’99 √
TCO’03 √
Green Mark √
Microsoft Windows PC98/99 √
DPMS VESA √
PC-Monitor
DDC 2B Version 1.3 √
USB External √
UL (USA) UL60950 3rd edition √
CSA (Canada) CAN/CSA-C22.2 No. 60950 √
Nordic / D.N.S.F EN60950 √
FIMKO EN60950 √
CE Mark 73/23/EEC √

IEC60950 √
Safety
EN60950 √
CB EN60950 √
EN60950 /
TUV/GS √
EK1-ITB 2000:2003
CCC (China) √
GOST EN60950 √
SASO √
CE Mark 89/336/EEC √
FCC (USA) FCC Part 15 B √

EN55022 Class B
√
EMC
CISPR 22 Class B √
VCCI (Japan) VCCI Class B √
BSMI (Taiwan) CNS 13438 √
C-Tick (Australia) AS/ NZS CISPR22 √
DHHS (21 CFR) USA X- Ray Standard √
X- Ray Requirement DNHW √
PTB German X- Ray standard √
TUV / Ergo √
Ergonomics ISO 13406-2 √
prEN50279 √

13
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Engineering Specification

Appendix: Physical Dimension Front View and Side view

Fig. 1 Physical Dimension Front View and Side view

14
Confidential
 5 4 3 2 1

3.3V_MCU
3.3V_MCU

D N1
BAV70LT1 D N2 D N3 D N4 D N5

2
2 1 BAV99 BAV99 BAV99 BAV99
P C5V
C1
3 3 3 3 0.01U ESD solution C 20 C 25 C 49

3
0.01U J 0.01U J 0.01U J

PC5V TP1

1
C2

2
0 .1U D1
R1 R2 6.2V TP2
U1 4.7K 4.7K R3 R4 R5
1 8
A0 VCC

1
D D
J1 75 75 75

G1
2 7
A1 WP TP3 R6 100 C3 0.047U
6 R ED-
3 6 11 1 TP4 R+ L1 Z60
A2 SCL D SUB_SCL
7 R7 100 C4 0.047U
R ED+
4 5 D SUB_SDA TP5 12 2 TP6 G+
VSS SDA R8 100 C5 0.047U
8 G REEN-
AT24C02A TP7 13 3 TP8 B+ L2 Z60
9 R9 100 C6 0.047U
GREEN+
TP9 14 4
R 10 0 D D C _WP_A 10 R 11 100 C7 0.047U
BLUE-
TP10 15 5 L3 Z60
R 12 100 C8 0.047U
R 35 BLUE+
R 13 R 14 47 TP11
D SUB_SDA
4.7K 2024012A15
A-detect
R 15 47 C9 C 10 C 11
DSUB_SCL 100 4.7P C 4.7P C 4.7P C
C 77

G2
3.3V_MCU D2 D3 0 .1U
6.2V 6.2V
R 16 200

1
H S YN C
R 17 200
V SYN C

2
D4 R 18 D5 R 19
6.2V 2K 6.2V 2K C 12 C 13
22P J 20P J

1
C C

3.3V_MCU

D N6
BAV70LT1
2 1 D VIPC5V

3
J2 3.3V_MCU

1 TP12
1 RX2- C 14
9 TP13
9 RX1- 0.1U
17 TP14 C 15
17 RX0- ESD solution
2 TP15 0.01U R 20 R 21
2 RX2+ U2
10 TP16 4.7K 4.7K
10 RX1+
2

18 TP17 1 8
18 RX0+ A0 VCC
3 TP18 D N7
3 BAV99 R 22 0
11 RX0- 3 RX0M 2 7
11 A1 WP
19
19
2

4 3 6 R 23 47
4 A2 SCL D VI_SCL
12 D N8
12
1

20 3 BAV99 R 24 0 4 5 R 25 47
20 RX0+ RX0P VSS SDA D VI_SDA
5
5
2

13 AT24C02A
13 D N9
21
21
1

6 TP19 3 BAV99 R 26 0
6 DVI_SCL RX1- RX1M
14 TP20 R 27 0 D D C _WP_D
14 DVIPC5V
2

22
22 TP21 D N10
7 DVI_SDA
7
1

15 3 BAV99 R 28 0 R 29
B 15 RX1+ RX1P B
23 TP22 4.7K
23 RXC+
2

8
8 TP23 Hot- Plug R 30 10K D N 11
16
16
1

24 TP24 3 BAV99 R 31 0
24 RXC- RX2- RX2M
2

3.3V_MCU 3.3V_MCU
G1 D N 12
G1
1

G2 3 BAV99 R 32 0
G2 RX2+ RX2P
D-detect
2

D N13 D N 14
1

3 BAV99 3 BAV99 R 33 0
RXC- RXCM
2

D6 D7 D8 C 16
2022009024 6.2V 6.2V 6.2V 0.01U D N 15
1

ESD solution 3 BAV99 R 34 0

RXC+ RXCP
1

A A

Project Code Model Name OEM/ODM Model Name

99.L1C72.001 Q7T4 NA
Title
INTERFACE BOARD

Size P CB P/N PC B Rev. Document Number Re v.

<Size> 99.L1C72.000-C3-304-001 1
48.L1C01.S02 S02

Date: Thursday, July 29, 2004 Sheet 1 of 6

Prepared By R eviewed By Ap proved By
AN GEL HU ALLEN PC LEE D AV EN WU
5 4 3 2 1
 5 4 3 2 1

Delete FB1, C20; FB2, C25 ;

6/16 change FB3,FB4,FB5 from
0805 to 0603

C 17

3.3V_MCU
R 3 .3DVCC 18P J Y1 R 3 .3DVCC R 2 .5DVCC
D C 18 24.576MHZ D
F B4

220 OHM
1 C 35 C 36 C 37 C 38 C 39 C 40 C 41
+ C 34 18P J
22U 25V 0 .1U 0 .1U 0.1U 0 .1U 0 .1U 0 .1U 0 .1U
<Spec>
2

R 3 .3DVCC

120
109

121
110

127

128
96
84
72
57
48

95
83
71
58
49

98
69
45

97
70
44
3.3V Ground
3.3V Ground
3.3V Ground
3.3V Ground
3.3V Ground
3.3V Ground
3.3V Ground

2.5V Ground
2.5V Ground
2.5V Ground
2.5V Ground
3.3V Power
3.3V Power
3.3V Power
3.3V Power
3.3V Power
3.3V Power
3.3V Power

2.5V Power
2.5V Power
2.5V Power
2.5V Power
XO 1 113 R 36 100 VOL_ADJ
XO TCON[12]/COUT/PWM2

1
XI 2 112
XI PWM0/REFCLK C 19
55 +
R 3 .3DVCC TMDS_VCC C 21 C 22 TCON[13]/COUT/PWM2 4.7U 25V
4
DPLL_VDD
5
APLL_VDD

2
0 .1U 0.1U 3 108
DPLL_GND AR1N R 37 100
8 107 BRT_ADJ
APLL_GND AR1P/TCON[0]
106
AR2N/TCON[1]

1
6 105
C 26 C 27 C 28 C 29 PLL_TEST1 AR2P/TCON[5] + C 23
7 104
PLL_TEST2 AR3N/TCON[6] 4.7U 25V
103
0 .1U 0 .1U 0.1U 0 .1U AR3P/TCON[7]
9 102
TMDS_TST/PWM1 AG1N/TCON[8]

2
12 101
EXT_RES AG1P/TCON[9]
RX2P 14 100
R 38 RX2P AG2N/TCON[10]
RX2M 15 99
4.7K RX2N AG2P/TCON[11]
RX1P 17
RX1P
RX1M 18
RX1N
RX0P 20 68
R 39 RX0P BG3N
RX0M 21 67
3.3V_MCU 1K RX0N BG3P
RXCP 23 66
RXCP BCLKN
RXCM 24 65
RXCN BCLKP
64
BB1N

TMDS_VCC
11
13
TMDS_VDD
TMDS_VDD
RTD2523 BB1P
BB2N
63
62
19 61
TMDS_VDD BB2P
26 60
TMDS_VDD BB3N
10 59
TMDS_GND BB3P
C 16 C
TMDS_GND
22
TMDS_GND
25
TMDS_GND
94 RXOIN0-
AG3N/TEAN
BLUE+ 30 93 RXOIN0+
B+ AG3P/TEAP
BLUE- 31 92 RXOIN1-
B- ACLKN/TEBN
33 91 RXOIN1+
SOG/ADC_TEST ACLKP/TEBP
GREEN+ 34 90 RXOIN2-
G+ AB1N/TECN
GREEN- 35 89 RXOIN2+
+2.5V R 2 .5DVCC G- AB1P/TECP
R ED+ 37 88 RXOCKIN-
R+ AB2N/TECLKN
R ED- 38 87 RXOCKIN+
R- AB2P/TECLKP
86 RXOIN3-
F B5 AB3N/TEDN
29 85 RXOIN3+
ADC_VDD AB3P/TEDP
AD C _VCC 36
220 OHM ADC_VDD
41
ADC_VDD
1

C 43 C 44 C 45 C 46 82 RXEIN0-
C 42 C 24 0 .1U BR1N/TOAN
+ 28 81 RXEIN0+

TCON[2]/SDIO[3]/PWM2
22U 25V 0 .1U 0.1U 0 .1U 0 .1U ADC_REFIO BR1P/TOAP
80 RXEIN1-
<Spec> BR2N/TOBN
27 79 RXEIN1+
ADC_GND BR2P/TOBP
2

32 78 RXEIN2-

TCON[4]/SDIO[1]
ADC_GND BR3N/TOCN

TCON[3]/SDIO2]
39 77

TCON[0]/VCLK
ADC_GND BR3P/TOCP RXEIN2+

TCON[11]/V[0]
TCON[10]/V[1]
TCON[9]/V[2]
TCON[8]/V[3]
TCON[7]/V[4]
TCON[6]/V[5]
TCON[5]/V[6]
TCON[1]/V[7]
40 76 RXECLK-
ADC_GND BG1N/TOCLKN
75

DDCSDA2
DDCSCL2
BG1P/TOCLKP RXECKIN+

DDCSDA
DDCSCL
RESET#
42 74

SDIO[0]
H S YN C AHS BG2N/TODN RXEIN3-

SCSB
43 73

SCLK
V SYN C AVS BG2P/TODP RXEIN3+
3.3V_MCU AD C _VCC

50
54
53
52
51
111
56

47
46
125
126

114
115
116
117
118
119
122
123
124
F B3

220 OHM
1

C 31 C 32 C 33
+ C 30
22U 25V 0 .1U 0.1U 0 .1U
<Spec>
RTD_SCLK
2

RTD_SDO/SDI
B S DIO1 B
S DIO2
S DIO3
RTD_SCSB
R 40 0
RESET
R 41 0
RTD_RESET

delete RN1, add R65

D SUB_SDA
R 67 D SUB_SCL R66;Delete RN2 Add R67;
4.7K R35: Delete R65,R66 0615

3.3V_MCU

A A

Project Code Model Name OEM/ODM Model Name

99.L1C72.001 Q7T4 NA
Title
INTERFACE BOARD

Size P CB P/N PC B Rev. Document Number Re v.

<Size> 99.L1C72.000-C3-304-001 1
48.L1C01.S02 S02

Date: Thursday, July 29, 2004 Sheet 2 of 6

Prepared By R eviewed By Ap proved By
AN GEL HU ALLEN PC LEE D AV EN WU
5 4 3 2 1
 5 4 3 2 1

delete RN4,RN5,RN6,RN8; 3.3V_MCU

Q1,R44,C49,R46,R47

8
7
6
5

4.7K
R N3
1
2
3
4
D D

I - KEY 3.3V_MCU

PW _SW
RTD_SCSB
PANEL_ON KE Y_MENU
C 47 R 42 R 43
D-detect 0 .1U U4 4.7K 4.7K
**C50 close to scaler, R43 close to MCU. 3.3V_MCU 1
A0 VCC
8

2 7
3.3V_MCU A1 WP
3 6

44

43

42

41

40
A2 SCL SC L

1
RESET 4 5 SD A

VDD3

DA0/P5.0

DA1/P5.1

DA2/P5.2

DA3/P5.3

DA4/P5.4

DA5/P5.5
NC

NC

VSYNC

HSYNC
C 48 GND SDA
0.22U K
R 68 AT24C04N-10SI-2.7
3.3V_MCU
3.3V_MCU 7 39 3.3V_MCU
RST DA8/HLFHO
8 38
VDD DA9/HALFV 4.7K
R 45 4.7K 9 37 D D C _ WP_D
P6.3/AD3 U5 HBLANK/P4.1
10 36 D D C_WP_A
C 50 6.8P J VSS VBLANK/P4.0
11 35
X2 DA7/HCLAMP
Y2 12 SOCKET P/N: 22.10079.044 34 K EY_RIGHT
X1 DA6/P5.6
12MHZ
C 51 6.8P J 13 33 L ED_ORG
SD A ISDA/P3.4/T0 P6.7/DA13

SC L 14 32 LE D_GRN
ISCL/P3.5/T1 P6.6/DA12 3.3V_MCU +2.5V
D D C _WP_A 15 31 BL_ON
STOUT/P4.2 MTV312MV64 P6.5/DA11

D D C _ WP_D 16
P6.2/AD2/HLFHI P6.4/DA10
30 VOL_ON GMT
C U6 C
17 29 DSUB_SCL 1 3
P1.0 HSCL/P3.0/Rxd VIN VOUT

HSDA/P3.1/Txd

GND
GND
P3.2/INT0

P6.1/AD1

P6.0/AD0
C 52 G950T65U C 53

2
G1
0.1U 0.1U
P1.1

P1.2

P1.3

P1.4

P1.5

P1.6

P1.7
18

19

20

21

22

23

24

25

26

27

28
D SUB_SDA

RTD_SDO/SDI

SDIO1 KEY_LEFT
SDIO2 KEY_EXIT
SDIO3 A-detect C 54
RTD_SCLK 100P
RTD_RESET 50V J

C 55
100P TP25
50V J

1
2
3
4
J3
R N7 BRT_ADJ TP26 1 2 TP27
1 2 BL_ON

4.7K
3 4
3 4 L4
5 6
5 6 L5 TP28
7 8 +5V
7 8
8
7
6
5 9 10 Z30 TP29 3.3V_MCU
TP30 9 10 220 OHM TP31
VOL_ADJ 11 12 VOL_ON
11 12
3.3V_MCU 2072060206
3.3V_MCU

B B

1
C 58 C 59 + C 56 C 60 + C 57 C 61 C 62 C 63
22U 25V 22U 25V
0 .1U 0 .1U 0 .1U 0 .1U 0.1U 0 .1U

2
C 64
220P J
2

L ED_ORG R 48 10K 1 2N3906

L ED_ORG Q2
R 49 220
3

LE D_GRN R 50 10K 1 2N3906

LE D_GRN Q3
R 51 220
3

C 65 C 66
0 .1U 0 .1U

J4 R 52 0

TP32 1
TP33 2
TP34 3
TP35 4
R 53 1K L6 TP36 5
KEY_EXIT
R 54 1K L7 TP37 6
KEY_LEFT
R 55 1K L8 TP38 7
K EY_RIGHT
R 56 1K L9 TP39 8
K EY_MENU
R 57 1K L10 TP40 9
PW _SW
R 58 1K L11
I - KEY
2060091109

C 67 C 68 C 69 C 70 C 71 C 72
A 100P 100P 100P 100P 100P 100P A
50V J 50V J 50V J 50V J 50V J 50V J

Project Code Model Name OEM/ODM Model Name

99.L1C72.001 Q7T4 NA
Title
INTERFACE BOARD

Size P CB P/N PC B Rev. Document Number Re v.

<Size> 99.L1C72.000-C3-304-001 1
48.L1C01.S02 S02

Date: Thursday, July 29, 2004 Sheet 3 of 6

Prepared By R eviewed By Ap proved By
AN GEL HU ALLEN PC LEE D AV EN WU
5 4 3 2 1
 5 4 3 2 1

D +5V D

5V_PANEL
R59

3
100K

1
Q4 + C73
1 ELM13401CA 22U 25V C74
0.1U

2
+5V

2
3
PANEL_ON
R60 20K 1 Q5 G(1)
2N3904 D(3)

1
S(2)

2
+ C75 R61 C76
OPEN 10K 0.1U
25V

2
C C

J5
G1 G1
1 1
5V_PANEL TP41 2
2
3 3
R62 0 TP42 4
R63 0 TP43 5 4
R64 0 TP44 6 5
6
7 7
TP45 8
RXEIN3+ 8
TP46 9
RXEIN3- 9
TP47 10
RXECKIN+ 10
TP48 11
B RXECLK- 11 B
TP49 12
RXEIN2+ 12
TP50 13
RXEIN2- 13
14 14
TP51 15
RXEIN1+ 15
TP52 16
RXEIN1- 16
17 17
TP53 18
RXEIN0+ 18
TP54 19
RXEIN0- 19
TP55 20
RXOIN3+ 20
TP56 21
RXOIN3- 21
TP57 22
RXOCKIN+ 22
TP58 23
RXOCKIN- 23
24 24
TP59 25
RXOIN2+ 25
TP60 26 Project Code Model Name OEM/ODM Model Name
RXOIN2- 26
TP61 27
RXOIN1+ 27 99.L1C72.001 Q7T4 NA
TP62 28
RXOIN1- 28
TP63 29 Title
RXOIN0+ 29
A RXOIN0- TP64 30 INTERFACE BOARD A
30
G2 G2 Size PCB P/N PCB Rev. Document Number R e v.
20K2085030 <Size>
48.L1C01.S02 S02 99.L1C72.000-C3-304-001 1

Date: Thursday, July 29, 2004 Sheet 4 of 6

Prepared By Reviewed By Approved By
ANGEL HU ALLEN PC LEE DAVEN WU
5 4 3 2 1
 5 4 3 2 1

D D

C C

1
5 9 5 9 5 9

B 4 8 4 8 4 8 B

3 7 3 7 3 7
Optical Points
2 6 2 6 2 6

H1 H2 H3
OP1 OP2 OP3
OP OP OP
HOLE-V8 HOLE-V8 HOLE-V8

A A
Project Code Model Name OEM/ODM Model Name
99.L1C72.001 Q7T4 NA
Title
INTERFACE BOARD

Size PCB P/N P C B R ev. Document Number R e v.

<Size> 99.L1C72.000-C3-304-001 1
48.L1C01.S02 S02

D ate: Thursday, July 29, 2004 Sheet 5 of 6

Prepared By R eviewed By A pproved By
ANGEL HU ALLEN PC LEE DAVEN W U
5 4 3 2 1
 5 4 3 2 1

1. Add C20, C25, C49, C77, R35

D D

C C

B B

A A

P r o j e c t Code Mo d e l Nam e OE M/OD M Mo d e l Nam e

9 9 .L 1 C72.001 Q7T4 NA

Title
I N T E R FAC E B OAR D

S ize P C B P /N P C B R e v. D o c u m e n t Num ber R e v.

<Size> 9 9 .L 1 C 7 2 .000-C3-304-001 1
4 8 .L 1 C 01.S02 S02

D a te : Th u r s d a y, J u l y 2 9 , 2004 S h eet 6 of 6
P r e p a r e d By R e vi e w e d B y A p p r o ve d B y
A N GE L H U AL L E N P C L EE D AVEN WU

5 4 3 2 1
Q7T4-FP71G LCD Monitor Service Guide
Trouble Shooting
Q7T4 TROUBLE SHOOTING GUIDE

No Display or display is unstable:

1.1 Interface Board:

No picture or picture unstable

Power off Yes Turn on power

No

Does cable plugs in No Check all of wire then turn on power

connector? switch again.

Yes

Does power stable? No Check Power BD

Yes

Is LED light green/orange? No Check control BD

Yes

Is LED status normal? No Check Flash Rom or replace it

Yes

Does crystal work correctly? No Check crystal CKT or replace it

Yes

Is interface BD normally? No Replace interface BD

Yes

Replace panel

1
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Trouble Shooting

2. BUTTON function:
2.1 Control Board

OSD is not working

Yes

Is control BD connecting? No Plug control BD then retry

Yes

Is bottom switch normally? Yes Replace control BD then retry

No

Replace Control BD

Is OSD working??

No

Check Interface BD

3. OSD function:

OSD doesn’t work

Is control BD working? No Replace control BD

Check interface BD

4. Power Board

2
Confidential
 Q7T4-FP71G LCD Monitor Service Guide
Trouble Shooting

Backlight didn't shine

Y Y
Replace Q761 IC801 PIN 9 IS 15V? LED shined?

N N

N Y
Plug CN701 again or PWM existed?
3.3V existed? IS I/F board connected?
checking I/F BD (BLT_ADJ)

Y Y N

N Replace new fuse

Plug CN601 again or Turn on level existed? N
checking PW BD (BLT_ON)

Y
Replace new fuse
N Y
Check CN801, CN802
Insert them again Check IC701 OK? Replace IC701
was pluged properly?

Y
N

Replace IC801,Q805 Y
Checking F601
Replace new fuse
Broke?

Y
Replace
Check IC601 Vcc
IC601,Q602,Q603
existed?
R602

Replace IC602,
IC702,D701 or check
I/F BD

3
Confidential
BENQ LCD Q7T4(FP71G) Spare Parts List
P/N: 99.L1C72.ASE

ITEM DESCRIPTION PART NO. LOCATION

1 PCBA I/F BD MI AUO M170EG01 55.L1C01.001

2 IC CONTROLER RTD2023 QFP 128P 71.02023.00E U3

3 IC EEPROM AT24C02N-10SI-1.8SON 72.02402.C01 U1

4 IC EEPROM AT24C04N-10SI-2.7SON 72.02404.N01 U4

5 IC VR G950T65U SOT-223 74.95065.03C U6

6 IC FLASH MTV312MV64 (AJ) PLCC44 71.31264.A03 U5

7 PCBA SPS BD MI QT74 EG01 55.L1C02.001

8 PCBA CTRL BD MI Q7T4 55.L1C03.001

9 LCDM 17 M170EG01 V.1 AUO 56.91L83.011

10 ASSY FC ABS 8020C Q7T4 60.L1C01.001

11 ASSY RC ABS 5003A Q7T4 60.L1C02.001

12 ASSY BASE-CLUM ABS 5003A Q7T4 60.L1C03.001

13 CTN B 456*423*114 Q7T4/BENQ 44.L1C01.001

14 CSN BTM EPS Q7T4 47.L1C01.001

15 CSN TOP EPS Q7T4 47.L1C02.001

16 CABLE SIGNAL 15/15P CORE*1 1.5M 50.L9005.501

17 CD MANUAL Q7T4 53.L1C01.001

18 ASSY BASE ABS 5003A Q7T4 60.L1C04.001

* THIS PARTS LIST MAY BE SUBJECT TO CHANGE

WITH PRIOR NOTICE BY CSD OF BENQ.

Page : 1 / 1