License #2B4FB

SAP2000 Analysis Report

Model Name: r1-ped 12.8m (1).SDB

22 May 2019
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

Contents
1. Model geometry......................................................................................................................................................... 3
1.1. Joint coordinates................................................................................................................................................ 3
1.2. Joint restraints................................................................................................................................................... 4
1.3. Element connectivity.......................................................................................................................................... 4
2. Material properties..................................................................................................................................................... 8
3. Section properties...................................................................................................................................................... 9
3.1. Frames.............................................................................................................................................................. 9
3.2. Areas............................................................................................................................................................... 12
3.3. Solids............................................................................................................................................................... 13
4. Load patterns........................................................................................................................................................... 13
4.1. Definitions........................................................................................................................................................ 13
5. Load cases.............................................................................................................................................................. 13
5.1. Definitions........................................................................................................................................................ 14
5.2. Static case load assignments.......................................................................................................................... 14
5.3. Response spectrum case load assignments................................................................................................... 14
6. Load combinations.................................................................................................................................................. 14
7. Design preferences................................................................................................................................................. 16
7.1. Steel design..................................................................................................................................................... 16
7.2. Concrete design............................................................................................. Error: Reference source not found
7.3. Aluminum design........................................................................................... Error: Reference source not found
7.4. Cold formed design........................................................................................ Error: Reference source not found
8. Design overwrites.................................................................................................. Error: Reference source not found
8.1. Steel design................................................................................................... Error: Reference source not found

List of Figures
Figure 1: Finite element model...................................................................................................................................... 3

List of Tables
Table 1: Joint Coordinates............................................................................................................................................. 3
Table 2: Joint Restraint Assignments............................................................................................................................. 4
Table 3: Connectivity - Frame........................................................................................................................................ 4
Table 4: Frame Section Assignments............................................................................................................................ 5
Table 5: Frame Release Assignments 1 - General, Part 1 of 2...................................................................................... 7
Table 5: Frame Release Assignments 1 - General, Part 2 of 2...................................................................................... 7
Table 6: Material Properties 02 - Basic Mechanical Properties...................................................................................... 8
Table 7: Material Properties 03a - Steel Data................................................................................................................ 9
Table 8: Material Properties 03b - Concrete Data.......................................................................................................... 9
Table 9: Material Properties 03e - Rebar Data............................................................................................................... 9
Table 10: Frame Section Properties 01 - General, Part 1 of 4....................................................................................... 9
Table 10: Frame Section Properties 01 - General, Part 2 of 4..................................................................................... 10
Table 10: Frame Section Properties 01 - General, Part 3 of 4..................................................................................... 11
Table 10: Frame Section Properties 01 - General, Part 4 of 4..................................................................................... 12
Table 11: Area Section Properties, Part 1 of 3............................................................................................................. 12
Table 11: Area Section Properties, Part 2 of 3............................................................................................................. 13
Table 11: Area Section Properties, Part 3 of 3............................................................................................................. 13
Table 12: Solid Property Definitions............................................................................................................................. 13
Table 13: Load Pattern Definitions............................................................................................................................... 13
Table 14: Load Case Definitions.................................................................................................................................. 14
Table 15: Case - Static 1 - Load Assignments............................................................................................................. 14
Table 16: Function - Response Spectrum - User......................................................................................................... 14
Table 17: Combination Definitions............................................................................................................................... 14

Page 2 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

Table 18: Preferences - Steel Design - Indian IS:800-1998, Part 1 of 2...................................................................... 16

1. Model geometry
This section provides model geometry information, including items such as joint coordinates, joint restraints, and
element connectivity.

Figure 1: Finite element model

1.1. Joint coordinates

Table 1: Joint Coordinates

Table 1: Joint Coordinates
Joint CoordSys CoordType GlobalX GlobalY GlobalZ
m m m
1 GLOBAL Cartesian 6.25000 0.75000 0.00000
2 GLOBAL Cartesian 7.50000 0.75000 0.00000
3 GLOBAL Cartesian 8.75000 0.75000 0.00000
4 GLOBAL Cartesian 10.00000 0.75000 0.00000
5 GLOBAL Cartesian 11.25000 0.75000 0.00000
6 GLOBAL Cartesian 12.50000 0.75000 0.00000
7 GLOBAL Cartesian 13.75000 0.75000 0.00000
8 GLOBAL Cartesian 15.00000 0.75000 0.00000
9 GLOBAL Cartesian 16.25000 0.75000 0.00000
10 GLOBAL Cartesian 17.50000 0.75000 0.00000
11 GLOBAL Cartesian 18.75000 0.75000 0.00000
32 GLOBAL Cartesian 6.25000 0.00000 0.00000
33 GLOBAL Cartesian 7.50000 0.00000 0.00000
34 GLOBAL Cartesian 8.75000 0.00000 0.00000
35 GLOBAL Cartesian 10.00000 0.00000 0.00000
37 GLOBAL Cartesian 11.25000 0.00000 0.00000
38 GLOBAL Cartesian 12.50000 0.00000 0.00000
62 GLOBAL Cartesian 18.75000 0.00000 0.00000
63 GLOBAL Cartesian 17.50000 0.00000 0.00000
64 GLOBAL Cartesian 16.25000 0.00000 0.00000
65 GLOBAL Cartesian 15.00000 0.00000 0.00000

Page 3 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

66 GLOBAL Cartesian 13.75000 0.00000 0.00000
94 GLOBAL Cartesian 6.25000 1.50000 0.00000
95 GLOBAL Cartesian 7.50000 1.50000 0.00000
96 GLOBAL Cartesian 8.75000 1.50000 0.00000
97 GLOBAL Cartesian 10.00000 1.50000 0.00000
98 GLOBAL Cartesian 11.25000 1.50000 0.00000
99 GLOBAL Cartesian 12.50000 1.50000 0.00000
104 GLOBAL Cartesian 18.75000 1.50000 0.00000
105 GLOBAL Cartesian 17.50000 1.50000 0.00000
106 GLOBAL Cartesian 16.25000 1.50000 0.00000
107 GLOBAL Cartesian 15.00000 1.50000 0.00000
108 GLOBAL Cartesian 13.75000 1.50000 0.00000

1.2. Joint restraints

Table 2: Joint Restraint Assignments

Table 2: Joint Restraint Assignments
Joint U1 U2 U3 R1 R2 R3

1 Yes Yes Yes No No No

11 Yes Yes Yes No No No
32 Yes Yes Yes No No No
62 Yes Yes Yes No No No
94 Yes Yes Yes No No No
104 Yes Yes Yes No No No

1.3. Element connectivity

Table 3: Connectivity - Frame

Table 3: Connectivity - Frame
Frame JointI JointJ Length
m
1 32 33 1.25000
2 33 34 1.25000
3 34 35 1.25000
4 35 37 1.25000
5 37 38 1.25000
6 38 66 1.25000
7 66 65 1.25000
8 65 64 1.25000
9 64 63 1.25000
10 63 62 1.25000
11 94 95 1.25000
12 95 96 1.25000
13 96 97 1.25000
14 97 98 1.25000
15 98 99 1.25000
16 99 108 1.25000
17 108 107 1.25000
18 107 106 1.25000
19 106 105 1.25000
20 105 104 1.25000
21 1 2 1.25000

Page 4 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

22 2 3 1.25000
23 3 4 1.25000
24 4 5 1.25000
25 5 6 1.25000
26 6 7 1.25000
27 7 8 1.25000
28 8 9 1.25000
29 9 10 1.25000
30 10 11 1.25000
31 94 1 0.75000
32 1 32 0.75000
33 95 2 0.75000
34 2 33 0.75000
35 96 3 0.75000
36 3 34 0.75000
37 97 4 0.75000
38 4 35 0.75000
39 98 5 0.75000
40 5 37 0.75000
41 99 6 0.75000
42 6 38 0.75000
43 108 7 0.75000
44 7 66 0.75000
45 107 8 0.75000
46 8 65 0.75000
47 106 9 0.75000
48 9 64 0.75000
49 105 10 0.75000
50 10 63 0.75000
51 104 11 0.75000
52 11 62 0.75000
205 94 33 1.95256
206 95 32 1.95256
208 95 34 1.95256
209 96 33 1.95256
211 96 35 1.95256
212 97 34 1.95256
214 97 37 1.95256
215 98 35 1.95256
217 98 38 1.95256
218 99 37 1.95256
220 99 66 1.95256
221 108 38 1.95256
223 108 65 1.95256
224 107 66 1.95256
226 107 64 1.95256
227 106 65 1.95256
229 106 63 1.95256
230 105 64 1.95256
232 105 62 1.95256
233 104 63 1.95256

Table 4: Frame Section Assignments

Table 4: Frame Section Assignments
Frame AnalSect DesignSect MatProp

1 ISMB600 ISMB600 Default

2 ISMB600 ISMB600 Default
3 ISMB600 ISMB600 Default

Page 5 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

4 ISMB600 ISMB600 Default
5 ISMB600 ISMB600 Default
6 ISMB600 ISMB600 Default
7 ISMB600 ISMB600 Default
8 ISMB600 ISMB600 Default
9 ISMB600 ISMB600 Default
10 ISMB600 ISMB600 Default
11 ISMB600 ISMB600 Default
12 ISMB600 ISMB600 Default
13 ISMB600 ISMB600 Default
14 ISMB600 ISMB600 Default
15 ISMB600 ISMB600 Default
16 ISMB600 ISMB600 Default
17 ISMB600 ISMB600 Default
18 ISMB600 ISMB600 Default
19 ISMB600 ISMB600 Default
20 ISMB600 ISMB600 Default
21 ISMB600 ISMB600 Default
22 ISMB600 ISMB600 Default
23 ISMB600 ISMB600 Default
24 ISMB600 ISMB600 Default
25 ISMB600 ISMB600 Default
26 ISMB600 ISMB600 Default
27 ISMB600 ISMB600 Default
28 ISMB600 ISMB600 Default
29 ISMB600 ISMB600 Default
30 ISMB600 ISMB600 Default
31 ISMB100 ISMB100 Default
32 ISMB100 ISMB100 Default
33 ISMB100 ISMB100 Default
34 ISMB100 ISMB100 Default
35 ISMB100 ISMB100 Default
36 ISMB100 ISMB100 Default
37 ISMB100 ISMB100 Default
38 ISMB100 ISMB100 Default
39 ISMB100 ISMB100 Default
40 ISMB100 ISMB100 Default
41 ISMB100 ISMB100 Default
42 ISMB100 ISMB100 Default
43 ISMB100 ISMB100 Default
44 ISMB100 ISMB100 Default
45 ISMB100 ISMB100 Default
46 ISMB100 ISMB100 Default
47 ISMB100 ISMB100 Default
48 ISMB100 ISMB100 Default
49 ISMB100 ISMB100 Default
50 ISMB100 ISMB100 Default
51 ISMB100 ISMB100 Default
52 ISMB100 ISMB100 Default
205 ISA75X75X8 ISA75X75X8 Default
206 ISA75X75X8 ISA75X75X8 Default
208 ISA75X75X8 ISA75X75X8 Default
209 ISA75X75X8 ISA75X75X8 Default
211 ISA75X75X8 ISA75X75X8 Default
212 ISA75X75X8 ISA75X75X8 Default
214 ISA75X75X8 ISA75X75X8 Default
215 ISA75X75X8 ISA75X75X8 Default
217 ISA75X75X8 ISA75X75X8 Default
218 ISA75X75X8 ISA75X75X8 Default
220 ISA75X75X8 ISA75X75X8 Default
221 ISA75X75X8 ISA75X75X8 Default
223 ISA75X75X8 ISA75X75X8 Default

Page 6 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

224 ISA75X75X8 ISA75X75X8 Default
226 ISA75X75X8 ISA75X75X8 Default
227 ISA75X75X8 ISA75X75X8 Default
229 ISA75X75X8 ISA75X75X8 Default
230 ISA75X75X8 ISA75X75X8 Default
232 ISA75X75X8 ISA75X75X8 Default
233 ISA75X75X8 ISA75X75X8 Default

Table 5: Frame Release Assignments 1 - General, Part 1 of 2

Table 5: Frame Release Assignments 1 - General, Part 1 of 2
Frame PI V2I V3I TI M2I M3I

31 No No No Yes Yes Yes

32 No No No No No No
33 No No No Yes Yes Yes
34 No No No No No No
35 No No No Yes Yes Yes
36 No No No No No No
37 No No No Yes Yes Yes
38 No No No No No No
39 No No No Yes Yes Yes
40 No No No No No No
41 No No No Yes Yes Yes
42 No No No No No No
43 No No No Yes Yes Yes
44 No No No No No No
45 No No No Yes Yes Yes
46 No No No No No No
47 No No No Yes Yes Yes
48 No No No No No No
49 No No No Yes Yes Yes
50 No No No No No No
51 No No No Yes Yes Yes
52 No No No No No No
205 No No No Yes Yes Yes
206 No No No Yes Yes Yes
208 No No No Yes Yes Yes
209 No No No Yes Yes Yes
211 No No No Yes Yes Yes
212 No No No Yes Yes Yes
214 No No No Yes Yes Yes
215 No No No Yes Yes Yes
217 No No No Yes Yes Yes
218 No No No Yes Yes Yes
220 No No No Yes Yes Yes
221 No No No Yes Yes Yes
223 No No No Yes Yes Yes
224 No No No Yes Yes Yes
226 No No No Yes Yes Yes
227 No No No Yes Yes Yes
229 No No No Yes Yes Yes
230 No No No Yes Yes Yes
232 No No No Yes Yes Yes
233 No No No Yes Yes Yes

Table 5: Frame Release Assignments 1 - General, Part 2 of 2

Table 5: Frame Release Assignments 1 - General, Part 2 of 2

Page 7 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

Frame PJ V2J V3J TJ M2J M3J

31 No No No No No No
32 No No No No Yes Yes
33 No No No No No No
34 No No No No Yes Yes
35 No No No No No No
36 No No No No Yes Yes
37 No No No No No No
38 No No No No Yes Yes
39 No No No No No No
40 No No No No Yes Yes
41 No No No No No No
42 No No No No Yes Yes
43 No No No No No No
44 No No No No Yes Yes
45 No No No No No No
46 No No No No Yes Yes
47 No No No No No No
48 No No No No Yes Yes
49 No No No No No No
50 No No No No Yes Yes
51 No No No No No No
52 No No No No Yes Yes
205 No No No No Yes Yes
206 No No No No Yes Yes
208 No No No No Yes Yes
209 No No No No Yes Yes
211 No No No No Yes Yes
212 No No No No Yes Yes
214 No No No No Yes Yes
215 No No No No Yes Yes
217 No No No No Yes Yes
218 No No No No Yes Yes
220 No No No No Yes Yes
221 No No No No Yes Yes
223 No No No No Yes Yes
224 No No No No Yes Yes
226 No No No No Yes Yes
227 No No No No Yes Yes
229 No No No No Yes Yes
230 No No No No Yes Yes
232 No No No No Yes Yes
233 No No No No Yes Yes

2. Material properties
This section provides material property information for materials used in the model.

Table 6: Material Properties 02 - Basic Mechanical Properties

Table 6: Material Properties 02 - Basic Mechanical Properties
Material UnitWeight UnitMass E1 G12 U12 A1
KN/m3 KN-s2/m4 KN/m2 KN/m2 1/C
Fe250 7.6973E+01 7.8490E+00 210000000 80769230. 0.300000 1.1700E-05
.0 77
HYSD500 7.6973E+01 7.8490E+00 200000000 76923076. 0.300000 1.1700E-05
.0 92

Page 8 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

M25 2.4993E+01 2.5485E+00 25000000. 10416666. 0.200000 5.5000E-06
00 67

Table 7: Material Properties 03a - Steel Data

Table 7: Material Properties 03a - Steel Data
Material Fy Fu FinalSlope
KN/m2 KN/m2
Fe250 250000.00 410000.00 -0.100000

Table 8: Material Properties 03b - Concrete Data

Table 8: Material Properties 03b - Concrete
Data
Material Fc FinalSlope
KN/m2
M25 25000.00 -0.100000

Table 9: Material Properties 03e - Rebar Data

Table 9: Material Properties 03e - Rebar Data
Material Fy Fu FinalSlope
KN/m2 KN/m2
HYSD500 500000.00 545000.00 -0.100000

3. Section properties
This section provides section property information for objects used in the model.

3.1. Frames

Table 10: Frame Section Properties 01 - General, Part 1 of 4

Table 10: Frame Section Properties 01 - General, Part 1 of 4
SectionName Material Shape t3 t2 tf tw t2b tfb
m m m m m m
AutoHSS Auto Select
BOX 100X100X4 Fe250 SD Section
Bracing (2-ISA) Fe250 SD Section
DC125 Fe250 SD Section
DC150 Fe250 SD Section
DC175 Fe250 SD Section
DC200 Fe250 SD Section
ISA100X100X10 Fe250 Angle 0.100000 0.100000 0.010000 0.010000
ISA100X100X12 Fe250 Angle 0.100000 0.100000 0.012000 0.012000
ISA150X150X12 Fe250 Angle 0.150000 0.150000 0.012000 0.012000
ISA50X50X5 Fe250 Angle 0.050000 0.050000 0.005000 0.005000
ISA65X65X6 Fe250 Angle 0.065000 0.065000 0.006000 0.006000
ISA75X75X8 Fe250 Angle 0.075000 0.075000 0.008000 0.008000
ISA90X90X8 Fe250 Angle 0.090000 0.090000 0.008000 0.008000
ISB113.5X113.5 Fe250 Box/Tube 0.113500 0.113500 0.004800 0.004800
X4.8

Page 9 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

ISB122X61X4.5 Fe250 Box/Tube 0.122000 0.061000 0.004500 0.004500
ISB132X132X4.8 Fe250 Box/Tube 0.132000 0.132000 0.004800 0.004800
ISB145X82X4.8 Fe250 Box/Tube 0.145000 0.082000 0.004800 0.004800
ISB172X92X5.4 Fe250 Box/Tube 0.172000 0.092000 0.005400 0.005400
ISB25X25X3.2 Fe250 Box/Tube 0.025000 0.025000 0.003200 0.003200
ISB38X38X3.2 Fe250 Box/Tube 0.038000 0.038000 0.003200 0.003200
ISB49.5X49.5X3. Fe250 Box/Tube 0.049500 0.049500 0.003600 0.003600
6
ISB50X25X3.2 Fe250 Box/Tube 0.050000 0.025000 0.003200 0.003200
ISB66X33X3.6 Fe250 Box/Tube 0.066000 0.033000 0.003600 0.003600
ISB72X72X4.0 Fe250 Box/Tube 0.072000 0.072000 0.004000 0.004000
ISB91.5X91.5X4. Fe250 Box/Tube 0.091500 0.091500 0.004500 0.004500
5
ISB96X48X4.0 Fe250 Box/Tube 0.096000 0.048000 0.004000 0.004000
ISMB100 Fe250 I/Wide Flange 0.100000 0.075000 0.007200 0.004000 0.075000 0.007200
ISMB125 Fe250 I/Wide Flange 0.125000 0.075000 0.007600 0.004400 0.075000 0.007600
ISMB150 Fe250 I/Wide Flange 0.150000 0.080000 0.007600 0.004800 0.080000 0.007600
ISMB175 Fe250 I/Wide Flange 0.175000 0.090000 0.008600 0.005500 0.090000 0.008600
ISMB200 Fe250 I/Wide Flange 0.200000 0.100000 0.010800 0.005700 0.100000 0.010800
ISMB500 Fe250 I/Wide Flange 0.500000 0.180000 0.017200 0.010200 0.180000 0.017200
ISMB600 Fe250 I/Wide Flange 0.600000 0.210000 0.020800 0.012000 0.210000 0.020800
ISMC125 Fe250 Channel 0.125000 0.065000 0.008100 0.005000
ISMC150 Fe250 Channel 0.150000 0.075000 0.009000 0.005400
ISMC175 Fe250 Channel 0.175000 0.075000 0.010200 0.005700
ISMC200 Fe250 Channel 0.200000 0.075000 0.011400 0.006100
ISMC300 Fe250 Channel 0.300000 0.090000 0.013600 0.007600
ISMC350 Fe250 Channel 0.350000 0.100000 0.013500 0.008100

Table 10: Frame Section Properties 01 - General, Part 2 of 4

Table 10: Frame Section Properties 01 - General, Part 2 of 4
SectionName Area TorsConst I33 I22 AS2 AS3
m2 m4 m4 m4 m2 m2
AutoHSS
BOX 100X100X4 0.001536 3.616E-06 2.363E-06 2.363E-06 0.000780 0.000780
Bracing (2-ISA) 0.003800 2.996E-07 3.600E-06 6.727E-06 0.001791 0.002043
DC125 0.003194 5.268E-08 8.280E-06 0.000010 0.001233 0.002869
DC150 0.004126 8.294E-08 0.000016 0.000018 0.001599 0.003784
DC175 0.004822 1.185E-07 0.000024 0.000016 0.001965 0.003186
DC200 0.005582 1.638E-07 0.000036 0.000026 0.002398 0.004796
ISA100X100X10 0.001903 6.333E-08 1.770E-06 1.770E-06 0.001000 0.001000
ISA100X100X12 0.002259 1.083E-07 2.070E-06 2.070E-06 0.001200 0.001200
ISA150X150X12 0.003459 1.659E-07 7.354E-06 7.354E-06 0.001800 0.001800
ISA50X50X5 0.000479 3.958E-09 1.100E-07 1.100E-07 0.000250 0.000250
ISA65X65X6 0.000744 8.928E-09 2.910E-07 2.910E-07 0.000390 0.000390
ISA75X75X8 0.001138 2.423E-08 5.900E-07 5.900E-07 0.000600 0.000600
ISA90X90X8 0.001379 2.935E-08 1.042E-06 1.042E-06 0.000720 0.000720
ISB113.5X113.5 0.002028 6.311E-06 3.933E-06 3.933E-06 0.001090 0.001090
X4.8
ISB122X61X4.5 0.001514 2.340E-06 2.789E-06 9.378E-07 0.001098 0.000549
ISB132X132X4.8 0.002383 0.000010 6.344E-06 6.344E-06 0.001267 0.001267
ISB145X82X4.8 0.002028 5.296E-06 5.552E-06 2.285E-06 0.001392 0.000787
ISB172X92X5.4 0.002659 9.089E-06 0.000010 3.817E-06 0.001858 0.000994
ISB25X25X3.2 0.000253 3.140E-08 1.890E-08 1.890E-08 0.000160 0.000160
ISB38X38X3.2 0.000416 1.382E-07 8.180E-08 8.180E-08 0.000243 0.000243
ISB49.5X49.5X3. 0.000628 3.582E-07 2.142E-07 2.142E-07 0.000356 0.000356
6
ISB50X25X3.2 0.000416 9.950E-08 1.163E-07 3.800E-08 0.000320 0.000160
ISB66X33X3.6 0.000628 2.717E-07 3.187E-07 1.052E-07 0.000475 0.000238
ISB72X72X4.0 0.001047 1.292E-06 7.903E-07 7.903E-07 0.000576 0.000576
ISB91.5X91.5X4. 0.001514 3.041E-06 1.876E-06 1.876E-06 0.000823 0.000823
5

Page 10 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

ISB96X48X4.0 0.001047 9.904E-07 1.176E-06 3.932E-07 0.000768 0.000384
ISMB100 0.001460 2.049E-08 2.575E-06 4.080E-07 0.000400 0.000900
ISMB125 0.001660 2.507E-08 4.490E-06 4.370E-07 0.000550 0.000950
ISMB150 0.001900 2.838E-08 7.264E-06 5.260E-07 0.000720 0.001013
ISMB175 0.002462 4.691E-08 0.000013 8.500E-07 0.000963 0.001290
ISMB200 0.003233 9.499E-08 0.000022 1.500E-06 0.001140 0.001800
ISMB500 0.011074 7.753E-07 0.000452 0.000014 0.005100 0.005160
ISMB600 0.015621 1.581E-06 0.000918 0.000027 0.007200 0.007280
ISMC125 0.001619 2.756E-08 4.164E-06 5.990E-07 0.000625 0.001053
ISMC150 0.002068 4.338E-08 7.794E-06 1.023E-06 0.000810 0.001350
ISMC175 0.002438 6.260E-08 0.000012 1.210E-06 0.000998 0.001530
ISMC200 0.002821 8.748E-08 0.000018 1.404E-06 0.001220 0.001710
ISMC300 0.004564 1.908E-07 0.000064 3.108E-06 0.002280 0.002448
ISMC350 0.005366 2.212E-07 0.000100 4.306E-06 0.002835 0.002700

Table 10: Frame Section Properties 01 - General, Part 3 of 4

Table 10: Frame Section Properties 01 - General, Part 3 of 4
SectionName S33 S22 Z33 Z22 R33 R22
m3 m3 m3 m3 m m
AutoHSS
BOX 100X100X4 0.000047 0.000047 0.000055 0.000055 0.039226 0.039226
Bracing (2-ISA) 0.000050 0.000067 0.000091 0.000109 0.030780 0.042073
DC125 0.000132 0.000137 0.000153 0.000168 0.050914 0.056695
DC150 0.000207 0.000209 0.000237 0.000256 0.061310 0.066548
DC175 0.000278 0.000208 0.000320 0.000254 0.071005 0.057882
DC200 0.000361 0.000292 0.000418 0.000354 0.080427 0.067693
ISA100X100X10 0.000025 0.000025 0.000025 0.000025 0.030498 0.030498
ISA100X100X12 0.000029 0.000029 0.000029 0.000029 0.030271 0.030271
ISA150X150X12 0.000068 0.000068 0.000068 0.000068 0.046109 0.046109
ISA50X50X5 3.064E-06 3.064E-06 3.100E-06 3.100E-06 0.015154 0.015154
ISA65X65X6 6.205E-06 6.205E-06 6.200E-06 6.200E-06 0.019777 0.019777
ISA75X75X8 0.000011 0.000011 0.000011 0.000011 0.022770 0.022770
ISA90X90X8 0.000016 0.000016 0.000016 0.000016 0.027489 0.027489
ISB113.5X113.5 0.000069 0.000069 0.000069 0.000069 0.044038 0.044038
X4.8
ISB122X61X4.5 0.000046 0.000031 0.000046 0.000031 0.042923 0.024888
ISB132X132X4.8 0.000096 0.000096 0.000096 0.000096 0.051596 0.051596
ISB145X82X4.8 0.000077 0.000056 0.000077 0.000056 0.052321 0.033567
ISB172X92X5.4 0.000118 0.000083 0.000118 0.000083 0.061707 0.037890
ISB25X25X3.2 1.512E-06 1.512E-06 1.510E-06 1.510E-06 0.008643 0.008643
ISB38X38X3.2 4.305E-06 4.305E-06 4.300E-06 4.300E-06 0.014023 0.014023
ISB49.5X49.5X3. 8.655E-06 8.655E-06 8.650E-06 8.650E-06 0.018468 0.018468
6
ISB50X25X3.2 4.652E-06 3.040E-06 4.650E-06 3.040E-06 0.016720 0.009558
ISB66X33X3.6 9.658E-06 6.376E-06 9.660E-06 6.370E-06 0.022527 0.012943
ISB72X72X4.0 0.000022 0.000022 0.000022 0.000022 0.027474 0.027474
ISB91.5X91.5X4. 0.000041 0.000041 0.000041 0.000041 0.035198 0.035198
5
ISB96X48X4.0 0.000024 0.000016 0.000024 0.000016 0.033507 0.019379
ISMB100 0.000052 0.000011 0.000052 0.000011 0.041996 0.016717
ISMB125 0.000072 0.000012 0.000072 0.000012 0.052008 0.016225
ISMB150 0.000097 0.000013 0.000097 0.000013 0.061832 0.016639
ISMB175 0.000145 0.000019 0.000145 0.000019 0.071879 0.018581
ISMB200 0.000224 0.000030 0.000224 0.000030 0.083152 0.021540
ISMB500 0.001809 0.000152 0.001809 0.000152 0.202071 0.035170
ISMB600 0.003060 0.000252 0.003060 0.000253 0.242436 0.041196
ISMC125 0.000067 0.000013 0.000067 0.000013 0.050714 0.019235
ISMC150 0.000104 0.000019 0.000104 0.000019 0.061391 0.022241
ISMC175 0.000140 0.000023 0.000140 0.000023 0.070835 0.022278
ISMC200 0.000182 0.000026 0.000182 0.000026 0.080306 0.022309

Page 11 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

ISMC300 0.000424 0.000047 0.000424 0.000047 0.118071 0.026096
ISMC350 0.000572 0.000057 0.000572 0.000057 0.136568 0.028328

Table 10: Frame Section Properties 01 - General, Part 4 of 4

Table 10: Frame Section Properties 01 - General, Part 4 of 4
SectionName AMod A2Mod A3Mod JMod I2Mod I3Mod MMod WMod

AutoHSS
BOX 100X100X4 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
Bracing (2-ISA) 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
DC125 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
DC150 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
DC175 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
DC200 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISA100X100X10 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISA100X100X12 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISA150X150X12 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISA50X50X5 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISA65X65X6 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISA75X75X8 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISA90X90X8 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB113.5X113.5 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
X4.8
ISB122X61X4.5 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB132X132X4.8 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB145X82X4.8 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB172X92X5.4 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB25X25X3.2 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB38X38X3.2 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB49.5X49.5X3. 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
6
ISB50X25X3.2 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB66X33X3.6 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB72X72X4.0 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISB91.5X91.5X4. 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
5
ISB96X48X4.0 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMB100 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMB125 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMB150 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMB175 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMB200 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMB500 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMB600 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMC125 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMC150 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMC175 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMC200 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMC300 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000
ISMC350 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000

3.2. Areas

Table 11: Area Section Properties, Part 1 of 3

Table 11: Area Section Properties, Part 1 of 3
Section Material AreaType Type DrillDOF Thickness BendThick F11Mod

Page 12 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

m m
Slab_125mm M25 Shell Shell-Thick Yes 0.125000 0.125000 1.000000

Table 11: Area Section Properties, Part 2 of 3

Table 11: Area Section Properties, Part 2 of 3
Section F22Mod F12Mod M11Mod M22Mod M12Mod V13Mod V23Mod

Slab_125mm 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000

Table 11: Area Section Properties, Part 3 of 3

Table 11: Area Section Properties, Part 3 of 3
Section MMod WMod

Slab_125mm 1.000000 1.000000

3.3. Solids

Table 12: Solid Property Definitions

Table 12: Solid Property Definitions
SolidProp Material MatAngleA MatAngleB MatAngleC
Degrees Degrees Degrees
SOLID1 M25 0.000 0.000 0.000

4. Load patterns
This section provides loading information as applied to the model.

4.1. Definitions

Table 13: Load Pattern Definitions

Table 13: Load Pattern Definitions
LoadPat DesignType SelfWtMult AutoLoad

DEAD DEAD 1.000000

Super Imposed SUPER DEAD 0.000000
Load
Windy (+) WIND 0.000000 None
Windy (-) WIND 0.000000 None
PEDESTRIAN PEDESTRIAN 0.000000
LIVE LL

5. Load cases
This section provides load case information.

Page 13 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

5.1. Definitions

Table 14: Load Case Definitions

Table 14: Load Case Definitions
Case Type InitialCond ModalCase BaseCase

DEAD LinStatic Zero

MODAL LinModal Zero
Super Imposed LinStatic Zero
Load
Windy (+) LinStatic Zero
Windy (-) LinStatic Zero
PEDESTRIAN LinStatic Zero
LIVE

5.2. Static case load assignments

Table 15: Case - Static 1 - Load Assignments

Table 15: Case - Static 1 - Load Assignments
Case LoadType LoadName LoadSF

DEAD Load pattern DEAD 1.000000

Super Imposed Load pattern Super Imposed 1.000000
Load Load
Windy (+) Load pattern Windy (+) 1.000000
Windy (-) Load pattern Windy (-) 1.000000
PEDESTRIAN Load pattern PEDESTRIAN 1.000000
LIVE LIVE

5.3. Response spectrum case load assignments

Table 16: Function - Response Spectrum - User

Table 16: Function - Response Spectrum - User
Name Period Accel FuncDamp
Sec
UNIFRS 0.000000 1.000000 0.050000
UNIFRS 1.000000 1.000000

6. Load combinations
This section provides load combination information.

Table 17: Combination Definitions

Table 17: Combination Definitions
ComboName ComboType CaseName ScaleFactor

DL Linear Add DEAD 1.000000

Page 14 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

DL Super Imposed 1.000000
Load
DL+LL Linear Add DL 1.000000
DL+LL PEDESTRIAN 1.000000
LIVE
DL+WL Linear Add DL 1.000000
DL+WL Windy (+) 1.000000
ENV Envelope DL 1.000000
ENV DL+LL 1.000000
ENV DL+WL 1.000000

Page 15 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

7. Design preferences
This section provides the design preferences for each type of design, which typically include material reduction
factors, framing type, stress ratio limit, deflection limits, and other code specific items.

7.1. Steel design

Table 18: Preferences - Steel Design - Indian IS:800-1998, Part 1 of 2

Table 18: Preferences - Steel Design - Indian IS:800-1998, Part 1 of 2
FrameType PatLLF SRatioLimit LatFactor DLRat SDLAndLLRat

Sway Frame 0.750000 0.950000 1.000000 120.000000 120.000000

Table 18: Preferences - Steel Design - Indian IS:800-1998, Part 2 of 2

Table 18: Preferences - Steel Design -
Indian IS:800-1998, Part 2 of 2
LLRat TotalRat NetRat

360.000000 240.000000 240.000000

Table: Steel Design 1 - Summary Data - Indian IS:800-1998, Part 1 of 2

Table: Steel Design 1 - Summary Data - Indian IS:800-1998, Part 1 of 2

Frame DesignSect DesignType Status Ratio RatioType

205 ISA75X75X8 Beam No Messages 0.410458 PMM

206 ISA75X75X8 Beam No Messages 0.143195 PMM
208 ISA75X75X8 Beam No Messages 0.332288 PMM
209 ISA75X75X8 Beam No Messages 0.108329 PMM
211 ISA75X75X8 Beam No Messages 0.241212 PMM
212 ISA75X75X8 Beam No Messages 0.075828 PMM
214 ISA75X75X8 Beam No Messages 0.151528 PMM
215 ISA75X75X8 Beam No Messages 0.043015 PMM
217 ISA75X75X8 Beam No Messages 0.061982 PMM
218 ISA75X75X8 Beam No Messages 0.036277 PMM
220 ISA75X75X8 Beam No Messages 0.036303 PMM
221 ISA75X75X8 Beam No Messages 0.061982 PMM
223 ISA75X75X8 Beam No Messages 0.043015 PMM
224 ISA75X75X8 Beam No Messages 0.151528 PMM
226 ISA75X75X8 Beam No Messages 0.075828 PMM
227 ISA75X75X8 Beam No Messages 0.241212 PMM
229 ISA75X75X8 Beam No Messages 0.108329 PMM
230 ISA75X75X8 Beam No Messages 0.332288 PMM
232 ISA75X75X8 Beam No Messages 0.143195 PMM
233 ISA75X75X8 Beam No Messages 0.410458 PMM
1 ISMB600 Beam No Messages 0.075425 PMM
2 ISMB600 Beam No Messages 0.132081 PMM
3 ISMB600 Beam No Messages 0.171537 PMM
4 ISMB600 Beam No Messages 0.194831 PMM
5 ISMB600 Beam No Messages 0.202535 PMM

Page 16 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

6 ISMB600 Beam No Messages 0.202535 PMM
7 ISMB600 Beam No Messages 0.194831 PMM
8 ISMB600 Beam No Messages 0.171537 PMM
9 ISMB600 Beam No Messages 0.132081 PMM
10 ISMB600 Beam No Messages 0.075425 PMM
11 ISMB600 Beam No Messages 0.075425 PMM
12 ISMB600 Beam No Messages 0.132083 PMM
13 ISMB600 Beam No Messages 0.171539 PMM
14 ISMB600 Beam No Messages 0.194833 PMM
15 ISMB600 Beam No Messages 0.202538 PMM
16 ISMB600 Beam No Messages 0.202538 PMM
17 ISMB600 Beam No Messages 0.194833 PMM
18 ISMB600 Beam No Messages 0.171539 PMM
19 ISMB600 Beam No Messages 0.132083 PMM
20 ISMB600 Beam No Messages 0.075425 PMM
21 ISMB600 Beam No Messages 0.064699 PMM
22 ISMB600 Beam No Messages 0.119023 PMM
23 ISMB600 Beam No Messages 0.159855 PMM
24 ISMB600 Beam No Messages 0.185116 PMM
25 ISMB600 Beam No Messages 0.193658 PMM
26 ISMB600 Beam No Messages 0.193658 PMM
27 ISMB600 Beam No Messages 0.185116 PMM
28 ISMB600 Beam No Messages 0.159855 PMM
29 ISMB600 Beam No Messages 0.119023 PMM
30 ISMB600 Beam No Messages 0.064699 PMM
31 ISMB100 Beam No Messages 0.072042 Major Shear
32 ISMB100 Beam No Messages 0.072042 Major Shear
33 ISMB100 Beam No Messages 0.083810 PMM
34 ISMB100 Beam No Messages 0.083810 PMM
35 ISMB100 Beam No Messages 0.140100 PMM
36 ISMB100 Beam No Messages 0.140100 PMM
37 ISMB100 Beam No Messages 0.177423 PMM
38 ISMB100 Beam No Messages 0.177423 PMM
39 ISMB100 Beam No Messages 0.197840 PMM
40 ISMB100 Beam No Messages 0.197840 PMM
41 ISMB100 Beam No Messages 0.204004 PMM
42 ISMB100 Beam No Messages 0.204004 PMM
43 ISMB100 Beam No Messages 0.197840 PMM
44 ISMB100 Beam No Messages 0.197840 PMM
45 ISMB100 Beam No Messages 0.177423 PMM
46 ISMB100 Beam No Messages 0.177423 PMM
47 ISMB100 Beam No Messages 0.140100 PMM
48 ISMB100 Beam No Messages 0.140100 PMM
49 ISMB100 Beam No Messages 0.083810 PMM
50 ISMB100 Beam No Messages 0.083810 PMM
51 ISMB100 Beam No Messages 0.072042 Major Shear
52 ISMB100 Beam No Messages 0.072042 Major Shear

Table: Steel Design 1 - Summary Data - Indian IS:800-1998, Part 2 of 2

Table: Steel Design 1 - Summary Data - Indian IS:800-1998, Part 2 of 2
Frame Combo Location ErrMsg WarnMsg
m
205 DL+WL 0.00000 No Messages No Messages
206 DL+WL 0.00000 No Messages No Messages
208 DL+WL 0.00000 No Messages No Messages
209 DL+WL 0.00000 No Messages No Messages
211 DL+WL 0.00000 No Messages No Messages
212 DL+WL 0.00000 No Messages No Messages
214 DL+WL 0.00000 No Messages No Messages
215 DL+WL 0.00000 No Messages No Messages
217 DL+WL 0.00000 No Messages No Messages
218 DL 1.00253 No Messages No Messages

Page 17 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

220 DL 0.97628 No Messages No Messages
221 DL+WL 0.00000 No Messages No Messages
223 DL+WL 0.00000 No Messages No Messages
224 DL+WL 0.00000 No Messages No Messages
226 DL+WL 0.00000 No Messages No Messages
227 DL+WL 0.00000 No Messages No Messages
229 DL+WL 0.00000 No Messages No Messages
230 DL+WL 0.00000 No Messages No Messages
232 DL+WL 0.00000 No Messages No Messages
233 DL+WL 0.00000 No Messages No Messages
1 DL 1.25000 No Messages No Messages
2 DL 1.25000 No Messages No Messages
3 DL 1.25000 No Messages No Messages
4 DL 1.25000 No Messages No Messages
5 DL 1.25000 No Messages No Messages
6 DL 0.00000 No Messages No Messages
7 DL 0.00000 No Messages No Messages
8 DL 0.00000 No Messages No Messages
9 DL 0.00000 No Messages No Messages
10 DL 0.00000 No Messages No Messages
11 DL 1.25000 No Messages No Messages
12 DL 1.25000 No Messages No Messages
13 DL 1.25000 No Messages No Messages
14 DL 1.25000 No Messages No Messages
15 DL 1.25000 No Messages No Messages
16 DL 0.00000 No Messages No Messages
17 DL 0.00000 No Messages No Messages
18 DL 0.00000 No Messages No Messages
19 DL 0.00000 No Messages No Messages
20 DL 0.00000 No Messages No Messages
21 DL 1.25000 No Messages No Messages
22 DL 1.25000 No Messages No Messages
23 DL 1.25000 No Messages No Messages
24 DL 1.25000 No Messages No Messages
25 DL 1.25000 No Messages No Messages
26 DL 0.00000 No Messages No Messages
27 DL 0.00000 No Messages No Messages
28 DL 0.00000 No Messages No Messages
29 DL 0.00000 No Messages No Messages
30 DL 0.00000 No Messages No Messages
31 DL+LL 0.75000 No Messages No Messages
32 DL+LL 0.00000 No Messages No Messages
33 DL 0.75000 No Messages No Messages
34 DL 0.00000 No Messages No Messages
35 DL 0.75000 No Messages No Messages
36 DL 0.00000 No Messages No Messages
37 DL 0.75000 No Messages No Messages
38 DL 0.00000 No Messages No Messages
39 DL 0.75000 No Messages No Messages
40 DL 0.00000 No Messages No Messages
41 DL 0.75000 No Messages No Messages
42 DL 0.00000 No Messages No Messages
43 DL 0.75000 No Messages No Messages
44 DL 0.00000 No Messages No Messages
45 DL 0.75000 No Messages No Messages
46 DL 0.00000 No Messages No Messages
47 DL 0.75000 No Messages No Messages
48 DL 0.00000 No Messages No Messages
49 DL 0.75000 No Messages No Messages
50 DL 0.00000 No Messages No Messages
51 DL+LL 0.75000 No Messages No Messages
52 DL+LL 0.00000 No Messages No Messages

Page 18 of 19
r1-ped 12.8m (1).SDB SAP2000 v14.2.2 - License #2B4FB

1. Model geometry 22 May 2019

Page 19 of 19