Scribd
Upload
38 views

Module 2: Robots Mechanisms Lecture 4: Industrial Manipulator Kinematics Objectives

This document provides an overview of industrial manipulator kinematics and accuracy/repeatability. It discusses the basic components of manipulators including links, joints, and end effectors. Forward and inverse kinematics are introduced for determining the end effector position from joint angles or vice versa. Accuracy is defined as how close the end effector gets to the target, while repeatability refers to the consistency of reaching the same general area. The document concludes by recapping kinematics and accuracy/repeatability concepts.

Uploaded by

Amjad Saeed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
38 views

Module 2: Robots Mechanisms Lecture 4: Industrial Manipulator Kinematics Objectives

This document provides an overview of industrial manipulator kinematics and accuracy/repeatability. It discusses the basic components of manipulators including links, joints, and end effectors. Forward and inverse kinematics are introduced for determining the end effector position from joint angles or vice versa. Accuracy is defined as how close the end effector gets to the target, while repeatability refers to the consistency of reaching the same general area. The document concludes by recapping kinematics and accuracy/repeatability concepts.

Uploaded by

Amjad Saeed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Module 2 : Robots mechanisms

Lecture 4 : Industrial Manipulator Kinematics

Objectives
In this course you will learn the following

Kinematics of Industrial Manipulators

Accuracy and Repeatability

Introduction

Manipulators are built as serial chains or parallel chains or occasionally a combination of both..

Link and joints (revolute and prismatic), that are mostly used in manipulators, are shown in Figure 4.1.1

3R planar manipulator is shown in Figure 4.1.2

2RPR planer manipulator is shown in Figure 4.1.2

Figure 4.1.2
Figure 4.1.1

In spatial manipulators (open chains) adjacent axes are parallel or perpendicular to each other.

Forward or direct kinematics & inverse kinematics

Direct kinematics: Here link parameters (link lengths) and joint variables (typically angles) are given and
one has to find out the position and orientation of the end-effector (EE).

Inverse kinematics: Given link parameters and position and orientation of the end effector, one has to
find joint variables.

Example of 2R & 3R manipulator are given in next sessions, for the forward & inverse kinematics problem.
Accuracy & Repeatability

Resolution (least-count), accuracy and repeatability are often sought by the user. The resolution may be
called as the least distance the robot end effector could move through. This depends on the resolution of
the actuator system, sensors used to control joint motions, and varies with position of EE in the
workspace. Accuracy is the difference between the position attained and the desired target position. When
a robot is programmed to reach a point repeatedly it may be reaching a cluster of points close to each
other. Such a robot has good repeatability. If this cluster is close to the targeted point the robot has not
only good repeatability but also good accuracy. A robot could provide good repeatability but poor accuracy
if this cluster is far from the targeted point.

Figure 4.1.3

In figure 4.1.3 the robot EE is required to reach the centre of the circle – the target point. The circle on
extreme left shows the situation when the robot has poor accuracy and poor repeatability. The circle in
the middle shows the EE has been repeatedly reaching positions which are close together though away
from the target point. The third picture shows the robot has repeatedly reached points close to the target
and this is a case of good repeatability and accuracy.

Recap
In this lecture we have examined:

Kinematics of Industrial Manipulators

Accuracy and Repeatability

Congratulations, you have finished Lecture 4. To view the next lecture select it from the left hand side
menu of the page

You might also like