Scribd
Upload
280 views4 pages

SOLIS Export Limit Settings Using A CT Clamp

The document provides 12 steps to set up an export limit using a CT clamp on a solar inverter. Key steps include: (1) accessing advanced settings and typing in the password "0010"; (2) selecting "Grid OFF" and then "EPM Settings" to set the backflow power limit; (3) selecting "Current Sensor" and testing the CT connection; and (4) returning the grid setting to "ON" and verifying successful export limit setup with the status "LYMBYEPM".

Uploaded by

Earl Ine
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
280 views4 pages

SOLIS Export Limit Settings Using A CT Clamp

The document provides 12 steps to set up an export limit using a CT clamp on a solar inverter. Key steps include: (1) accessing advanced settings and typing in the password "0010"; (2) selecting "Grid OFF" and then "EPM Settings" to set the backflow power limit; (3) selecting "Current Sensor" and testing the CT connection; and (4) returning the grid setting to "ON" and verifying successful export limit setup with the status "LYMBYEPM".

Uploaded by

Earl Ine
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

EXPORT LIMIT

SETTINGS
Using a CT Clamp
NOTE: The CT clamp should be installed on the main board with the arrow on CT facing the
grid. The CT cable should NOT be run along the AC cable, it may cause interference.

SETTING UP EXPORT LIMIT USING A CT CLAMP

STEP 1: Press Enter on the inverter screen.

Enter

STEP 2: Use Up/Down keys to go to


advanced settings and press Enter. Advanced Settings

Enter

Up and Down Keys

STEP 3: Press Down key twice and up key


once, to type the password as 0010. Then
press Enter.
Enter

Up and Down Keys

STEP 4: Use the up/down keys to scroll to


Grid ON/ Grid OFF. Then press Enter.
Grid ON/ Grid OFF

Enter

STEP 5: Select the Grid OFF option and


Operation light turned OFF
press Enter. You will see the operation light
turn OFF.
Grid OFF

Enter

W: www.solisinverters.com.au
Ph: 03 8555 9516
E: [email protected]
STEP 6: Use Up/Down key to scroll to EPM
settings/ Internal EPM/ Export Power Set,
whichever is available on your screen.
EPM Settings
Then press Enter.
Enter

STEP 7: Go to Backflow Power and press


Enter.
Backflow Power

Enter

STEP 8: Use the Up/Down keys to set the Set Backflow


Backflow power according to your Power
requirements. For Example: If your export
limit is 5kW you need to set Backflow Enter
power as 5000W or +5000W. Press Enter.

STEP 9: Use Up/Down keys to find Mode Select. Use Up/Down keys to find ‘Current Sensor’.
Press Enter, to confirm the selected option. Then press “ESC” to backout.

STEP 10: Now turn the Grid ON in Advanced Settings.


(Go to Advanced Settings by pressing ESC thrice < Set password 0010 < Go to Grid ON/Grid
OFF < Select Grid ON < Press Enter).

W: www.solisinverters.com.au
Ph: 03 8555 9516
E: [email protected]
STEP 11: After the Grid option is ON, go onto EPM settings/ Internal EPM/ Export Power Set
and press Enter. Choose Mode Select → Current Sensor→ You will get two options when
you select Current Sensor.

• Click CT Link Test and press Enter.


You will see status as ‘Correct’ – meaning everything is working fine.
If not, you will see ‘Error’ on the screen if the connection is not proper. Or you
will see ‘NG’ on the screen if the CT is installed in the wrong direction.
• CT sample ratio
If you need to change the CT ratio, Select CT sample ratio and set according to
your requirements (default is 3000:1)
STEP 12: Press ESC to exit to the main screen. The status displayed will be LYMBYEPM,
which indicates you have successfully set up the export limit.

‘ALL DONE’
HAVE A GOOD DAY!

3
W: www.solisinverters.com.au
Ph: 03 8555 9516
E: [email protected]

You might also like