User Manual

User Manual DRC-40DK/41DK

• Thank
• Thank you
you for
for purchasing
purchasing COMMAX
COMMAXproducts.
products.
• Please
• Please carefully
carefully read
read this
this User’s
User’sGuide
Guide(in
(inparticular,
particular,precautions
precautionsfor
forsafety)
safety)before
beforeusing
usingaaproduct
productand
andfollow
follow
instructions
instructions to
to use
use aa product
product exactly.
exactly.
• The
• The company
company isis not
not responsible
responsible for
forany
anysafety
safetyaccidents
accidentscaused
causedby
byabnormal
abnormaloperation
operationof
ofthe
theproduct.
product.
 Contents

Safety Warning & Caution······································· 2

1. Overview ························································ 4
2. How to use ····················································· 4
3. Wiring Diagram ·············································· 10
4. Installation ···················································· 11
5. Package······················································· 11
6. Specification ················································· 12

1
 Safety Warning & Caution
Please follow the things described below in order to prevent any
danger or property damage.

Prohibition.

Warning It may cause a serious damage or

No disassembly
injury if violated.

No touch

Must follow strictly.

Shows plugging out the power cord

Caution It may cause a minor damage or
injury if violated.
without an exception

Shows the warning and caution for an electric shock.

Shows the warning and caution for a fire.

Warning

Please don’t use several Please don’t bend the power Please don’t handle the power Please plug out the power
products at the same time on cable excessively or it may cable with a wet hand. cable from the socket when
one power socket. cause an electric shock. ·It may cause an electric not using it for a long period
·It may cause a fire due to an ·fire when using a damaged shock. of time.
abnormal overheating. power cable. ·It may shorten the product
lifespan or cause a fire.
Power & Installation

Please don’t install the Please don’t install the Please don’t use and connect When installing the product
product in the place where product with the lightening this product with other that generates heat, please
there is much oil, smoke or and thunder. products with different rated install the product away from
humidity. ·It may cause an electric voltage the wall (10cm) for the
·It may cause an electric shock or fire. ·It may cause a disorder or ventilation.
shock or fire. fire. ·It may cause a fire due to
the increased internal
temperature.

2
2
 Warning
Please don’t disassemble, If an abnormal sound, burning Please don’t insert any Please use only the designated
repair or rebuild this product smell or smoke is coming out metallic or burnable materials batteries for the products of
Cleaning & Use

arbitrarily (please contact the of the product, please plug out into the ventilation hole. using DC power.
service center if a repair is the power cable and contact a ·It may cause an electric ·It may cause an electric
needed. service center. shock or fire. shock or fire.
·It may cause an electric ·It may cause an electric
shock or fire. shock or fire.

Caution
Please plug the power cable Please hold the plug tightly When connecting the power When installing the product,
firmly into the inner end when unplugging the power cables after cutting the cable, please fix it firmly while using
·It may cause a fire. cable (a part of the copper please install the product with the wall-mounting unit and
wire may be disconnected if power off screws.
the grabbing is only made on ·It may cause an electric ·It may cause an injury from
the cord when pulling out the shock or fire the falling object.
cable).
·It may cause an electric
shock or fire
Power & Installation

Please be careful when using Please check the use voltage Please avoid direct rays of the Please don’t install the
an AC circuit breaker since and current for the DC-only sun or heating devices at a product on an unstable place
there is a possibility of an products and use the time of installation. or small support board.
electric shock. appropriate rectifier. ·It may cause a fire. ·It may cause an injury if it
·It may cause a fire. falls down while in use.

When cleaning the product, Please don’t drop the product Please use the designated
please rub it with a soft and on the ground and don’t apply connection cable within the
Cleaning & Use

dry cloth after plugging out a shock . maximum calling distance

the power cable. (Please don’t ·It may cause a failure. designated for the product
use any chemical products ·It may reduce the product
such as wax, benzene, alcohol performance.
or cleanser.)

3
3
 1. Overview

No. contents No. contents

1 Camera 6 Enter button
2 Microphone 7 Speaker
3 White LED & Illuminance sensor 8 Call button
4 Keypad button 9 RF Card Tag
5 Back/Cancel button 10 Camera angle adjustment
11 Connecting port/ WIRE for door realese 12 Anti-theft switch

2. How to use
* Default behavior

- This product uses DC 12V / 1A adapter (RF-1A recommended, sold separately).

- If the power supply from the adapter is poor (disconnection or malfunction), the power
supplied from the monitor can be used as an emergency power source.

<Notes when using emergency power>

1) The emergency power source is supplied from monitor for 30 seconds when the
monitor is called by the camera.

2) In this case, some functions may cause difference from normal operation.
(Required function such as door opening is normal.)

3) Emergency power may not be used if wiring is poor or the distance is too long.

4
 * Button description

Image Description

Back, Cancel ⑤ (C : Cancel)

Use this button to cancel the function.

OK Button ⑥ (E : Enter)
Use this button for setting and execution.

* Anti-theft alarm function ⑫

- To prevent the device from being stolen, the alarm sounds when removed from the wall.
However, the alarm sounds only when power is supplied to the unit.

- To enhance security function, the automatic call is sent to monitor call as the alarm occurs.
The automatic call operates at all time when removed from the wall, regardless of power
supply status.

* Reset password

- If you forget your password, you can reset it as follows.

1) With the monitor, enter the door camera monitoring function.

Try to press door opening button 7 times quickly within 20 seconds.

2) Then, LED of the camera is blinking and push OK Button ( E ) for 3 seconds to reset
password.

2-2. Set the functions

<Required>
1) The initial password is 1.2.3.4. Be sure to change the initial password before use.
2) 0000, 1234, 4321 can not be set as a password.
3) Password can be set from 4 to 12 digits.
(The password out of this range is not available)

5
 2-2-1. Password setting

1) Password registration / change

① Press program number (0) and press OK button (E)

② Enter the existing password (Initial: 1, 2, 3, 4) and press the OK button (E)
③ If the password change mode is successfully entered, the KEY LED will blink.
④ Click the new password to be changed.
⑤ Press the OK button (E), the key LED stops blinking and the setting is completed.

2) RF card registration

- Up to 1,024 cards can be registered.

① Press program number (3) and press OK button (E)

② Enter the password and press the OK button (E).
③ When the RF card registration mode is successfully entered, the KEY LED will blink.
④ Tag the card to be registered to the RF receiver.
If you tag another card continuously, you can register all the cards at once.
⑤ Press the Cancel button (C) and the KEY LED stops blinking and registration is
completed.

3) Delete individual RF cards

6
① Press program number (4) and press OK button (E)
② Enter the password and press the OK button (E).
③ When individual deletion mode is successfully entered, the KEY LED will blink.
④ Tag the card to be deleted to the RF receiver.
If you tag another card continuously, you can delete multiple cards at once.
⑤ Press the Cancel button (C) and the KEY LED stops blinking and individual deletion
is completed.

4) Delete all RF cards

① Press program number (5) and press OK button (E)

② Enter the password and press the OK button (E).
③ When all deletion mode is successfully entered, the KEY LED will blink.
④ Press and hold the OK button (E) for 2 seconds, the whole deletion will proceed
with the beep sound.
⑤ When the whole deletion is completed, beep sound and KEY LED will stop..

5) Door opening with password

- Door open by Password

① After entering the password, press the door number you want to open and then press
OK button (E).
ex) When opening door # 1: 2580 -> 1 -> OK button (E)
- Door open by RF card
① After tagging RF card to the RF receiver, press the door number you want to open
ex) When opening door number 1: Card tag -> 1
② When the door is opened successfully, the operation is completed with the beep
sound.
7
 6) Communication Volume adjustment

① Press program number (6) and press OK button (E)

② Enter the password and press the OK button (E).
③ When the call volume control mode is successfully entered, the KEY LED will blink.
④ The volume of communication can be adjusted from level 1 to 3.
(Enter the number between 1~3.)
⑤ After enter the level number, press the OK button (E) and the key LED stops blinking
and the setting is completed. When completed, beep sound is heard as the number
of level.

7) Beep(Touch and so on) Volume adjustment

① Press program number (7) and press OK button (E)

② Enter the password and press the OK button (E).
③ When the beep volume control mode is successfully entered, the KEY LED will
blink.
④ The beep volume can be adjusted from level 1 to 2.
(Enter the number between 1~2.)
⑤ After enter the level number, press the OK button (E) and the key LED stops
blinking and the setting is completed. When completed, beep sound is heard as
the number of level.

<Notes>
1) Even if the beep volume is adjusted, during Calling and Communication mode, it
is fixed in level 1 to maintain Communication quality
(It cannot be adjust the beep volume during Calling and Communication mode)

8
8) ON/OFF Anti-theft switch

① Press program number (8) and press OK button (E)

② Enter the password and press the OK button (E).
③ When anti-theft setting mode is successfully entered, the KEY LED will blink.
④ Anti-theft function OFF : Enter 0
Anti-theft function ON : Enter 1
⑤ Press the OK button (E) as key LED stops blinking and the setting is completed.

<Notes>
1) After installing the unit on the wall, turn on the anti-theft switch.
2) If the unit is detached from the wall, an alarm occurs.
In this case, the alarm will stop 10 seconds after the unit is re-attached to the wall.
The alarm can be turned off with above program (8) while alarm rings.

9) Touch LED setting

① Press program number (9) and press OK button (E)

② Enter the password and press the OK button (E).
③ If touch LED setting mode is successfully entered, the KEY LED will blink.
④ LED ON only when the key touched: Input 0
LED ON every time with power supplied: Input 1
⑤ After entering the number, press the OK button (E) and the key LED stops blinking
and the setting is completed.

9
 10) Opening time of door adjustment

① Press program number (10) and press OK button (E)

② Enter the password and press the OK button (E).
③ When the opening time of door mode is successfully entered, the KEY LED will blink.
④ The opening time can be adjusted from level 1 to 3. (Enter the number between 1~3.)
⑤ After enter the level number, press the OK button (E) and the key LED stops blinking
and the setting is completed. When completed, beep sound is heard as the number of level.

3. Wiring Diagram

* Precautions
- When wiring the household monitor, connect as follows.
Failure to do the wiring as shown below may cause the video / audio noise.

10
4. Installation

5. Package

Item Description Qty

CONN. 4Px300 4 wire connector 
CONN. 2Px300 2 wire connector 
Bracket Bracket for installation 
Screw GH1T 4x18 Bracket screw 
Screw PHM 3x8 Bracket + Monitor 
User Manual English version manual 

11
 6. Specification

Model DRC-40DK/41DK
Power 12VDC/1A (Adaptor)
12VDC (emergency power from monitor
Communication Duplex communication
Min. illumination 0.1Lux (up to 300mm from camera / with normal LED operation)
Illumination White LED equipped (night vision)
Image sensor CMOS IMAGE SENSOR (0.52 megapixels)
Imaging angle 93° horizontal, 50° vertical, 110° diagonal
Adjustable angle 13° (pan and tilt)
RF Module 13.56MHz
Operation temp. -10℃(tested up to -40℃) ~ +50℃
Dimension (mm) DRC-40DK : 127(W)x193(H)x54(D), DRC-41DK : 127(W)x193(H)x63(D)
28 meters (Φ 0.5 UTP), It must be observed.
Distance
Resistance under 10 Ω per 100 meters on UTP Cat 5e.

<Caution>
We recommend the COMMAX adaptor.
We are not responsible for problem caused by the use of adaptors of other company.

12
513-11, Sangdaewon-dong,
513-11, Sangdaewon-dong, Jungwon-gu,
Jungwon-gu, Seongnam-si,
Seongnam-si, Gyeonggi-do,
Gyeonggi-do, Korea
Korea
Int’l Business
Int’l Business Dept. Tel. :: +82-31-7393-540~550
Dept. Tel. +82-31-7393-540~550 Fax.
Fax. :: +82-31-745-2133
+82-31-745-2133
Web
Web site
site :: www.commax.com
www.commax.com
Edited.2019.12.27 Printed In Korea / 2016.04.104