User Manual

Original Instructions

ControlLogix EtherNet/IP Network Devices

Catalog Numbers 1756-EN2F, 1756-EN2T, 1756-EN2TK, 1756-EN2TP, 1756-EN2TPK, 1756-EN2TPXT, 1756-EN2TR, 1756-
EN2TRK, 1756-EN2TRXT, 1756-EN2TSC, 1756-EN2TXT, 1756-EN3TR, 1756-EN3TRK, 1756-EN4TR, 1756-EN4TRK, 1756-
EN4TRXT, 1756-ENBT, 1756-ENBTK, 1756-EWEB
Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, and
operation of this equipment before you install, configure, operate, or maintain this product. Users are required to
familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,
and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are
required to be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may
be impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from
the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or
liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or
software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,
Inc., is prohibited

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous
environment, which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

Labels may also be on or inside the equipment to provide specific precautions.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may
reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to
potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL
Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).
 Table of Contents
Table of Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 1
ControlLogix EtherNet/IP Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Network Device Overview ControlLogix Network Device Features. . . . . . . . . . . . . . . . . . . . . . . . . . 7
EtherNet/IP Network Specifications. . . . . . . . . . . . . . . . . . . . . . . . 10
Electronic Keying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Protected Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Enabling Explicit Protected Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disabling Explicit Protected Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Secure Digital Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Secure Digital Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Disable Secure Digital Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CIP Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 2
Connect to the EtherNet/IP Set the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Network Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Set the IP Address with Rotary Switches . . . . . . . . . . . . . . . . . . . . . . . . 18
Other Methods to Set the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reset the Module IP Address to Factory Default Value . . . . . . . . . . . 19

Appendix A
ControlLogix Network Device Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Status Indicators Single-Port Module Status Indicators . . . . . . . . . . . . . . . . . . . . . . . 24
Dual-Port Module Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . 25

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 3

Table of Contents

Notes:

4 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 Preface

This manual describes how you can use ControlLogix® EtherNet/IP™

communication modules with a Logix 5000™ controller and communicate with
various devices on the Ethernet/IP network.

Use this manual if you program applications that use EtherNet/IP networks
with these Logix 5000 controllers:
• CompactLogix™ controller
• ControlLogix controller

Conventions Be sure to understand these concepts and tools:

• FactoryTalk® Linx
• Logix Designer
• ControlFLASH Plus™
• HMIs
• SNMP tools

Additional Resources These documents contain additional information concerning related products
from Rockwell Automation.
Resource Description
1756 ControlLogix Communication Modules Specifications, Specifications for ControlLogix communication
publication 1756-TD003 modules.
Ethernet Design Considerations Reference Manual, Provides details about how to use EtherNet/IP
publication ENET-RM002 communication modules with Logix 5000 controllers
and communicate with other devices on the
EtherNet/IP network.
EtherNet/IP Network Devices User Manual, Describes how to install, configure, and operate the
publication ENET-UM006 Compact 5000™ I/O EtherNet/IP adapters.
EtherNet/IP Modules Installation Instructions, Provides information about how to complete these
publication ENET-IN002 tasks with EtherNet/IP communication modules in a
Logix 5000 control system:
• Install the module
• Configure initial application setup
• Troubleshoot application anomalies that are
related to EtherNet/IP communication module use
EtherNet/IP Media Planning and Installation Manual Provides details about how to install, configure, and
This manual is available from the Open DeviceNet® Vendor maintain linear and Device Level Ring (DLR) networks
Association (ODVA) at: http://www.odva.org. by using Rockwell Automation EtherNet/IP devices
that are equipped with embedded switch technology.
EtherNet/IP Embedded Switch Technology Application Provides details about how to install, configure, and
Guide, publication ENET-AP005 maintain linear and Device Level Ring (DLR) networks
by using Rockwell Automation EtherNet/IP devices
that are equipped with embedded switch technology.
EtherNet/IP Device Level Ring Application Technique, Describes DLR network operation, topologies,
publication ENET-AT007 configuration considerations, and diagnostic
methods.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 5

Preface

Resource Description
EtherNet/IP Socket Interface Application Technique, Describes the socket interface that you can use to
publication ENET-AT002 program MSG instructions to communicate between a
Logix5000 controller via an EtherNet/IP module and
Ethernet devices that do not support the EtherNet/IP
application protocol, such as bar code scanners, RFID
readers, or other standard Ethernet devices.
Troubleshoot EtherNet/IP Networks Application Technique, Provides details about how to assign IP addresses to
publication ENET-AT003 and how to troubleshoot EtherNet/IP networks and
devices.
Industrial Automation Wiring and Grounding Guidelines, Provides general guidelines for installing a Rockwell
publication 1770-4.1 Automation industrial system.
Product Certifications website, http:// Provides declarations of conformity, certificates, and
www.rockwellautomation.com/global/certification/ other certification details.
overview.page

You can view or download publications at

http://www.rockwellautomation.com/global/literature-library/overview.page.
To order paper copies of technical documentation, contact your local
Allen-Bradley distributor or Rockwell Automation sales representative.

6 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 Chapter 1

ControlLogix EtherNet/IP Network Device

Overview

Topic Page
Overview 7
ControlLogix Network Device Features 7
Electronic Keying 11
Protected Mode 12
Secure Digital Card 13
CIP Security 15

Overview EtherNet/IP™ networks are communication networks that offer a

comprehensive suite of messages and services for many automation
applications.

This open network standard uses commonly available Ethernet

communication products to support real-time I/O messaging, information
exchange, and general messaging.

ControlLogix Network Device The ControlLogix® EtherNet/IP network devices:

Features • Facilitate high-speed data transfer between some Logix 5000™
controllers and remote I/O modules.
• Connect to multiple EtherNet/IP network topologies.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 7

Chapter 1 ControlLogix EtherNet/IP Network Device Overview

Figure 1 shows how Rockwell Automation EtherNet/IP communication

modules fit into a control system.

Figure 1 - EtherNet/IP Communication Modules in a Control System

1769-L27ERM 5069-L340ERM
1769 I/O Modules 5069 I/O Modules Distributed I/O

1756-EN4TR
1756 I/O Modules
ControlLogix 5580 Controller
1756 I/O Modules
Redundancy Module EtherNet/IP EtherNet/IP ControlNet EtherNet/IP ControlNet
Logix5575
10/100 BASE T

RUN FORCE SD OK
PRI COM OK LNK1 LNK2 OK LNK NET OK LNK NET OK

Star Topology
REM PR
RUN OG

1794-AENT
Switch
1 2

1794 I/O Modules

1769-L18ERM
1734 I/O Modules PowerFlex®
Drive

5069-AEN2TR
5069 I/O Modules
Workstation

1783-ETAP
Workstation Stratix® 5400

DLR Topology

1783-ETAP
PanelView™ Terminal

Kinetix® 6500
Servo Drive

X100
FLEX 5000 I/O FLEX 5000 I/O FLEX 5000 I/O
TM TM TM
POWER STATUS POWER STATUS POWER STATUS
FLEX 5000 I/O
TM

1756-EN4TR
EtherNet/IP™ Adapter

X10 STATUS

NET

LINK 1 5094-IB16 DIGITAL 16 INPUT 24 VDC 1 1 TB3 5094-OB16 DIGITAL 16 OUTPUT 24 VDC 1 2 TB3 5094-OW8I RELAY 8 OUTPUT ISOLATED 2 2 TB3W
X1
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7
IP ADDRESS LINK 2
5094-AENTR
POWER
PRP
DLR

ControlLogix Controller
1734-AENTR 1738-AENTR
5094-IB16
1734 I/O Modules 1738 I/O Modules
FLEX 5000™ I/O

8 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 ControlLogix EtherNet/IP Network Device Overview Chapter 1

Table 1 - EtherNet/IP Communication Modules

Cat. No.(1) Description Media Communication Integrated TCP Logix
Rate Motion on the Connections Connections
EtherNet/IP
Network Axes,
Max
1756-EN2F EtherNet/IP bridge, fiber Fiber 10/100 Mbps 8 128 256
1756-EN2T EtherNet/IP bridge, copper Copper 10/100 Mbps 8 128 256
1756-EN2TK
1756-EN2TR, EtherNet/IP bridge, embedded switch, copper Dual copper 10/100 Mbps 8 128 256
1756-EN2TRK
1756-EN2TXT ControlLogix-XT™, extended temperature Copper 10/100 Mbps 8 128 256
EtherNet/IP bridge, copper, for extreme
environments
1756-EN2TRXT ControlLogix-XT, extended temperature Dual copper 10/100 Mbps 8 128 256
EtherNet/IP bridge, embedded switch, copper
1756-EN2TSC EtherNet/IP secure communication module Copper 10/100 Mbps — 128 256
1756-EN3TR, EtherNet/IP bridge, embedded switch, copper Dual copper 10/100 Mbps 128 128 256
1756-EN3TRK
1756-EN4TR, EtherNet/IP bridge, embedded switch, copper Copper 10/100 Mbps 256 512 1000 I/O
1756-EN4TRK 1 Gbps 528 Messaging
1756-EN4TRXT ControlLogix-XT, extended temperature Copper 10/100 Mbps 256 512 1000 I/O
EtherNet/IP bridge, embedded switch, copper 1 Gbps 528 Messaging
1756-ENBT, EtherNet/IP bridge, copper Copper 10/100 Mbps — 64 128
1756-ENBTK
1756-EWEB Ethernet web server module Copper 10/100 Mbps — 64 128
(1) A catalog number ending in a K denotes a conformal coating.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 9

Chapter 1 ControlLogix EtherNet/IP Network Device Overview

EtherNet/IP Network Specifications

Table 2 - EtherNet/IP Network Specifications
Cat. No. Connections CIP Unconnected Ethernet Node Packet Rate Capacity (packets/second)(3) SNMP Support
Messages Count, Max (password
TCP CIP (backplane + I/O HMI and MSG required)
Ethernet)
1756-ENBT 64 128(1) 64 + 64 — 5000 900 Yes
(1)
1756-EN2F 128 256 128 + 128 — IMPORTANT: Packet rates for 2000 Yes
(1) ControlLogix EtherNet/IP
1756-EN2T 128 256 128 + 128 — communication modules 2000 Yes
depend on series and firmware
1756-EN2TXT 128 256(1) 128 + 128 — revision. 2000 Yes
(1)
1756-EN2TR 128 256 128 + 128 — 2000 Yes
(1)
1756-EN2TRXT 128 256 128 + 128 — 2000 Yes
1756-EN2TSC 128 256(1) 128 + 128 — • 1800 without Yes
encryption
• 930 with
encryption
1756-EN3TR 128 256(1) 128 + 128 — 2000 Yes
1756-EN4TR 512 1000 I/O 256+256 — • 50,000 without CIP Security • 3,700 without CIP Yes
528 (2) • 25,000 with integrity Security
• 15,000 with integrity and • 2,700 with
confidentiality integrity
• 1,700 with
integrity and
confidentiality
1756-EN4TRXT 512 1000 I/O 256+256 — • 50,000 without CIP Security • 3,700 without CIP Yes
528(2) • 25,000 with integrity Security
• 15,000 with integrity and • 2,700 with
confidentiality integrity
• 1,700 with
integrity and
confidentiality
1756-EWEB 64 128(1) 128 + 128 — — 900 Yes
(1) CIP connections can be used for all explicit or all implicit applications. For example, a 1756-ENBT module has a total of 128 CIP connections that can be used for any combination of connections.
(2) There are 1000 CIP I/O connections and 528 CIP messaging connections.
(3) Total packet rate capacity = I/O Produced Tag, max + HMI/MSG, max. Packet rates vary depending on packet size. For more detailed specifications, see the EDS file for a specific catalog number.

10 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 ControlLogix EtherNet/IP Network Device Overview Chapter 1

Electronic Keying Electronic Keying reduces the possibility that you use the wrong device in a
control system. It compares the device that is defined in your project to the
installed device. If keying fails, a fault occurs. These attributes are compared.

Attribute Description
Vendor The device manufacturer.
Device Type The general type of the product, for example, digital I/O module.
Product Code The specific type of the product. The Product Code maps to a catalog number.
Major Revision A number that represents the functional capabilities of a device.
Minor Revision A number that represents behavior changes in the device.

The following Electronic Keying options are available.

Keying Option Description

Compatible Lets the installed device accept the key of the device that is defined in the project when the
Module installed device can emulate the defined device. With Compatible Module, you can typically
replace a device with another device that has the following characteristics:
• Same catalog number
• Same or higher Major Revision
• Minor Revision as follows:
– If the Major Revision is the same, the Minor Revision must be the same or higher.
– If the Major Revision is higher, the Minor Revision can be any number.
Disable Keying Indicates that the keying attributes are not considered when attempting to communicate with
a device. With Disable Keying, communication can occur with a device other than the type
specified in the project.
ATTENTION: Be cautious when using Disable Keying; if used incorrectly, this option can lead
to personal injury or death, property damage, or economic loss.
We strongly recommend that you do not use Disable Keying.
If you use Disable Keying, you must take full responsibility for understanding whether the
device being used can fulfill the functional requirements of the application.
Exact Match Indicates that all keying attributes must match to establish communication. If any attribute
does not match precisely, communication with the device does not occur.

Carefully consider the implications of each keying option when selecting one.

IMPORTANT Changing Electronic Keying parameters online interrupts connections to the device
and any devices that are connected through the device. Connections from other
controllers can also be broken.
If an I/O connection to a device is interrupted, the result can be a loss of data.

For more detailed information on Electronic Keying, see Electronic Keying in

Logix 5000 Control Systems Application Technique, publication LOGIX-
AT001.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 11

Chapter 1 ControlLogix EtherNet/IP Network Device Overview

Protected Mode The1756-EN2T, 1756-EN2TP, 1756-EN2TR, and 1756-EN4TR support

explicit protected mode.(1) When in this mode, the module does not allow any
configuration changes.

Enabling Explicit Protected Mode

To enable the module in an “explicit protected mode state”, follow these steps.

1. Set the rotary switches to position ‘900’.

2. Power up the device, and wait for the display to scroll, “Protected Mode
– Change Switch Settings”.
3. Power down the device.
4. Set the switches for normal operation.
5. Power up the device.
6. The device is now in Explicit Protected Mode.

Operation in Explicit Protected Mode

While working in protected mode, the module rejects any CIP™ explicit
messages that would change the configuration of the module. For example, you
cannot change the IP address, speed, or duplex settings when the module had
Explicit Protected Mode enabled.

Disabling Explicit Protected Mode

To disable the “explicit protected mode state”, follow these steps.

1. Set the rotary switches on position ‘000’.

2. Power up the device, and wait for the display to scroll, “Unprotected
Mode – Change Switch Settings”.
3. Power down the device.
4. Set the switches for normal operation.
5. Power up the device.
6. The device is now in Unprotected Mode.

(1) Versions 11.001 and later.

12 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 ControlLogix EtherNet/IP Network Device Overview Chapter 1

Secure Digital Card Secure Digital Card

The 1756-EN4TR EtherNet/IP Bridge supports the use of a Secure Digital

(SD) card to store configuration data, for example, the IP address or network
communication rate for each port.

The SD card slot is inside the front panel of the module.

SD Card inside front panel.

When the card is powered up, the device uses the configuration from the card if
the configuration does not exist in the device. When a blank card is inserted, or
powered up, the configuration is copied from the device to the card that was
inserted.

If the module powers up with a configuration that does not match the
configuration on the already inserted SD card, the configuration on the SD
card is used.

If the module is already powered, and an SD card is inserted, a warning message

is displayed.

TIP To see other potential error messages, see Table 4 on page 25.

To change these results, do one of two things. One option is to do an out of box
reset on the module, if you want to use the configuration on the SD card. A
second option is to modify one of the configuration settings on the device, if
you want to use the configuration on the device.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 13

Chapter 1 ControlLogix EtherNet/IP Network Device Overview

Enable/Disable Secure Digital Card

To enable or disable the SD card, use one of the following methods.

• Using a CIP Generic Message
– To enable, set Attribute 4 (‘SOCKET DISABLED’) to ‘0’ (‘False’) of
Removable Media Socket Object instance (0x3A4, 932 decimal)
– To disable, set Attribute 4 (‘SOCKET DISABLED’) to ‘1’ (‘True’)
of Removable Media Socket Object instance (0x3A4, 932 decimal).
• Enable/Disable using the Add-on Profile.

The adapter supports the use of a 1784-SD1 (1 GB) and 1784-SD2 (2 GB)
card. You can use third-party SD cards with the controller. You can use SD
cards with as much as 32 GB of memory.

IMPORTANT Rockwell Automation does not test the use of third-party SD cards with the
device.

If you use an SD card other than those cards that are available from
Rockwell Automation, unexpected results can occur. For example, you can
experience data corruption or data loss.

SD cards that are not provided by Rockwell Automation can have different
industrial, environmental, and certification ratings as those cards that are
available from Rockwell Automation. These cards can have difficulty with
survival in the same industrial environments as the industrially rated versions
available from Rockwell Automation.

14 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 ControlLogix EtherNet/IP Network Device Overview Chapter 1

CIP Security CIP Security™ is a standard, open-source communication method that helps to
provide a secure data transport across an EtherNet/IP network.

The secure data transport is used between certain connected devices to help
protect the devices from threats posed by unauthorized users with malicious
intent.

CIP Security uses encryption to secure communication on an EtherNet/IP

network, resulting in greater data integrity and confidentiality.

Rockwell Automation uses the following products to implement CIP Security:

• FactoryTalk® Policy Manager
• FactoryTalk Linx
• Studio 5000® Design Environment
• CIP Security-enabled Rockwell Automation® products, for example, the
product described in this publication(1)

For more information on CIP Security, including which products support CIP
Security, see the CIP Security Application Technique, publication SECURE-
AT001.

(1) In this document, CIP Security is applicable to 1756-EN4TR, 1756-ENRTRK, and 1756-EN4TRXT modules.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 15

Chapter 1 ControlLogix EtherNet/IP Network Device Overview

Notes:

16 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 Chapter 2

Connect to the EtherNet/IP Network

Topic Page
Set the IP Address 18
Set the IP Address with Rotary Switches 18
Other Methods to Set the IP Address 19
Reset the Module IP Address to Factory Default Value 19

EtherNet/IP™ networks are communication networks that offer a

comprehensive suite of messages and services for many automation
applications.

The following are examples of applications that use EtherNet/IP networks:

• Real-Time Control
• Time Synchronization
• Motion

This open network standard uses commonly available Ethernet

communication products to support real-time I/O messaging, information
exchange, and general messaging.

EtherNet/IP networks also support CIP Safety™, which makes the

simultaneous transmission of safety and standard control data and diagnostics
information over a common network possible.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 17

Chapter 2 Connect to the EtherNet/IP Network

Set the IP Address The following conditions are required to set the IP address.

Requirements
To set the IP address, have the following:
• EtherNet/IP or USB drivers that are installed on the programming
workstation
• MAC ID from the device, which is on the label on the side of the device
• Recommended IP address for the device

Set the IP Address with This graphic shows the rotary switches on a 1756 EtherNet/IP communication
module. The three rotary switches at the bottom of the module, labeled X, Y,
Rotary Switches and Z, can be used for setting the IP address. The rotary switch in the upper
left corner of the module is reserved for future configuration.

32794 M

At powerup, the module reads the rotary switches to determine if they are set
to a valid number for the last portion of the IP address. Valid numbers range
from 001…254.

18 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 Connect to the EtherNet/IP Network Chapter 2

If the settings are a valid number, these conditions result:

• IP address = 192.168.1.xxx (where xxx represents the switch settings)
• Subnet mask = 255.255.255.0
• Gateway address = 0.0.0.0

TIP Some modules now provide a gateway address of 192.168.1.1 when the
network address is set with rotary switches.

• The module does not have a host name that is assigned to it, nor does it
use any Domain Name System

We recommend that you set the rotary switches to a valid number before
installing the module.

If the rotary switches are not set to a valid number, the module attempts to use
the BOOTP/DHCP server to set the IP address.

IMPORTANT For more information on how to use the BOOTP/DHCP server to set the IP
address, see EtherNet/IP Network Configuration Manual,
publication ENET-UM006

Other Methods to Set the IP The 1756-EN4TR module supports the following additional methods to
change the IP address:
Address
• BOOTP/DHCP utility
• RSLinx® Classic software
• Using Secure Digital Card
• For more information on how to use these methods, see EtherNet/IP
Network Configuration Manual, publication ENET-UM006.

Reset the Module IP Address You can reset the configuration of the module to its factory default value with
the following methods:
to Factory Default Value
• If the module has rotary switches, set the switches to 888 and cycle
power.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 19

Chapter 2 Connect to the EtherNet/IP Network

Notes:

20 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 Appendix A

ControlLogix Network Device Status Indicators

Topic Page
Status Indicators 21
Single-Port Module Status Indicators 24
Dual-Port Module Status Indicators 25

Status Indicators The following graphics show the status indicators for these modules (extended-
temperature versions not shown).

Figure 2 - 1756-EN2F, 1756-EN2T (Single-port Modules)

EtherNet/IPTM
10/100 BASE T

LINK NET OK

Module Status Display

OK Status Indicator
LINK NET OK

Network Status Indicator (NET)

Link Status
Indicator (LINK)

Figure 3 - 1756-EN2TR, 1756-EN3TR (Dual-port Modules)

Module Status Display

OK Status Indicator

Link Status
Indicators (LINK) Network Status Indicator (NET)

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 21

Appendix A ControlLogix Network Device Status Indicators

Figure 4 - 1756-EN2TP (Dual-port Module)

Module Status Display

OK Status Indicator

Network Status Indicator (NET)

Link Status
Indicators (LINK)

1756-EN2TP
Figure 5 - 1756-EN2TSC (Single-port Module)

VPN 32730

Module Status Display

OK Status Indicator

Link Status
Indicator (LINK) Network Status Indicator (NET)

Figure 6 - 1756-EN4TR (Dual-port Module)(1)

Module Status Display
Parallel Redundant Protocol
Status Indicator
Redundant Adapter Status Indicator
SD Card Status Indicator

OK Status Indicator

Network Status Indicator (NET)

Link Status
Indicators (LINK)

(1) Parallel Redundant Protocol and Redundant Adapter features are not available in the initial release. Check the
Product Compatibility and Download Center (PCDC) to see if it is available in your firmware revision.

22 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 ControlLogix Network Device Status Indicators Appendix A

Figure 7 - 1756-ENBT (Single-port Module)

VPN

Module Status Display

OK Status Indicator

Network Status Indicator (NET)

Link Status
Indicator (LINK)

Figure 8 - 1756-EWEB (Single-port Module)

Module Status Display

OK Status Indicator

Network Status Indicator (NET)

Link Status
Indicator (LINK)

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 23

Appendix A ControlLogix Network Device Status Indicators

Single-Port Module Status Indicators

Table 3 - Single-port Module Status Indicators
Status Indicator Description Status State
Module Status Display Alphanumeric display that scrolls messages. For example, — —
when a module is operating normally, the display scrolls
the module’s IP address.
Link Status (LINK) Indicates the current state of the module regarding Off One of these conditions exists:
transmission of data on the EtherNet/IP™ network. • The module is not powered.
– Verify that there is chassis power.
– Verify that the module is completely inserted
into the chassis and backplane.
– Make sure that the module has been
configured.
• No link exists on the port.
Flashing green Activity exists on the port.
Green The port is active, but not receiving traffic.
OK Status (OK) Indicates the current state of the module. For example, this Off The module is not powered.
status indicator indicates if the module is executing • Verify that there is chassis power.
power-up testing, in the process of a firmware update or
operating normally. • Verify that the module is completely inserted into
the chassis and backplane.
• Make sure that the module has been configured.
Flashing green The module is not configured. The Module Status
display scrolls: BOOTP or
DHCP<Mac_address_of_module>
For example: BOOTP 00:0b:db:14:55:35
Configure the module.
Green The module is operating correctly. The IP address
scrolls across the Module Status display.
Flashing red The module detected a recoverable minor fault. Check
the module configuration. If necessary, reconfigure
the module.
Red The module detected an unrecoverable major fault.
Cycle power to the module. If this power cycle does not
clear the fault, replace the module.
Network Status (NET) Indicates if CIP™ connections are established. Off One of these conditions exists:
• The module is not powered.
– Verify that there is chassis power.
– Verify that the module is completely inserted
into the chassis and backplane.
– Make sure that the module has been
configured.
• The module is powered but does not have an IP
address. Assign an IP address to the module.
Flashing green The controller has an IP address and one of these
conditions exists:
• The module has not established any CIP
connections.
If connections are configured for this module,
check the connection originator for the connection
error code.
• All connections to the device have timed out or
been closed.

24 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 ControlLogix Network Device Status Indicators Appendix A

Table 3 - Single-port Module Status Indicators

Status Indicator Description Status State
Network Status (NET) Indicates if CIP connections are established. Green The module has established at least 1 CIP connection
and is operating properly. The IP address scrolls across
the Module Status display.
Red The module is in conflict mode. It shares an IP address
with another device on the network. The current IP
address scrolls across the Module Status display. The
display scrolls: OK <IP_address_of_this_module>
Duplicate IP
<Mac_address_of_duplicate_node_detected>
For example: OK 10.88.60.196 Duplicate IP -
00:00:BC:02:34:B4
Change the IP address of the module.
Flashing green/flashing The module is performing its power-up testing.
red

Dual-Port Module Status Indicators

Table 4 - Dual-port Module Status Indicators
Status Indicator Description Status State
Module Status Display Alphanumeric display that scrolls messages. For — —
example, when a module is operating normally, the
display scrolls the module’s IP address.
OK Indicates the current state of the module. For Off The module is not powered.
example, this status indicator indicates if the module • Verify that there is chassis power.
is executing power-up testing, in the process of a
firmware update or operating normally. • Verify that the module is completely inserted into the chassis
and backplane.
• Make sure that the module has been configured.
Flashing green The module is not configured. The Module Status display scrolls:
BOOTP or DHCP<Mac_address_of_module>
For example: BOOTP 00:0b:db:14:55:35
Configure the module.
Green The module is operating correctly. The Module Status display
scrolls: OK <IP_address_of_this_module>
For example: OK 10.88.60.160
Flashing red The module detected a recoverable minor fault. Check the
module configuration. If necessary, reconfigure the module.
Red The module detected an unrecoverable major fault. Cycle power
to the module. If this power cycle does not clear the fault, replace
the module.
Both of these The module’s main firmware image must be updated. Follow
conditions exist: these steps:
• Status Indicator is 1. Update the firmware image.
Red 2. Cycle power to the module.
• Module Status
Display is scrolling:
Image Update
Needed
Flashing red and green The module is performing its power-up testing.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 25

Appendix A ControlLogix Network Device Status Indicators

Table 4 - Dual-port Module Status Indicators

Status Indicator Description Status State
Network Status (NET) Indicates if CIP connections are established. Off One of these conditions exists:
IMPORTANT: The new-series 1756-EN2TR and • The module is not powered.
1756-EN3TR modules have a NET status indicator.
The older-series 1756-EN2TR and 1756-EN3TR – Verify that there is chassis power.
modules do not have a NET status indicator. – Verify that the module is completely inserted into the
chassis and backplane.
– Make sure that the module has been configured.
• The module is powered but does not have an IP address.
Assign an IP address to the module.
Flashing green The controller has an IP address and one of these conditions
exists:
• The module has not established any CIP connections.
If connections are configured for this module, check the
connection originator for the connection error code.
• All connections to the device have timed out or been closed.
Green The module has established at least 1 CIP connection and is
operating properly. The IP address scrolls across the Module
Status display.
Red The module is in conflict mode. It shares an IP address with
another device on the network. The module’s current IP address
scrolls across the Module Status display. The display scrolls: OK
<IP_address_of_this_module> Duplicate IP
<Mac_address_of_duplicate_node_detected>
For example: OK 10.88.60.196 Duplicate IP - 00:00:BC:02:34:B4
Change the module’s IP address.
Flashing green/ The module is performing its power-up testing.
flashing red
Link Status Off One of these conditions exists:
(LINK 1, LINK 2) • The module is not powered.
– Verify that there is chassis power.
– Verify that the module is completely inserted into the
chassis and backplane.
– Make sure that the module has been configured.
• No link exists on the port.
• The port is administratively disabled.
• The port is disabled due to rapid ring faults (LNK2).
Flashing green Activity exists on the port.
Green One of these conditions exists:
• A link exists on the port, but no traffic is being received.
• The ring network is operating normally on active ring
supervisor (LNK2).
• A ring partial network fault was detected on the active ring
supervisor (LNK2).
Link Status Flashing red When the corresponding LAN A/B Parallel Redundancy Protocol
(LAN A, LAN B) (PRP) Warning bit is set.

26 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 ControlLogix Network Device Status Indicators Appendix A

Table 4 - Dual-port Module Status Indicators

Status Indicator Description Status State
(1)
SD The SD indicator shows if the SD card is in use Off No activity is occurring with the SD card. You can safely remove
the card, if necessary.
Flashing green The module is reading from or writing to the SD card.
IMPORTANT: Do not remove the SD card while the module is
Solid green reading or writing. Let the read/write complete without
interruption. If you interrupt the read/write, data corruption or
loss can occur.
Flashing red One of the following exists:
• The SD card does not have a valid file system.
• The SD card drew excessive current and power has been
removed from the card.
Solid red The module does not recognize the SD card.
Parallel Redundancy Check Firmware Revision for availability of this feature.
Protocol (PRP)(1)
Redundant Adapter (RA)(1) Check Firmware Revision for availability of this feature.
(1) Status indicators only available on the 1756-EN4TR, 1756-EN4TRK, 1756-EN4TRXT.

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 27

Appendix A ControlLogix Network Device Status Indicators

Notes:

28 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

 Index

A R
additional resources 5 real-time I/O messaging 7

B S
BOOTP/DHCP utility 19 secure digital card (SD) 13
single-port module 24
specifications
C EtherNet/IP network 10
CIP security 15 status indicators
compatible modules 11 1756-EN2T 21
control system 8 1756-EN2TP 22
conventions 5 1756-EN2TR 21
1756-EN2TSC 22
1756-EN4TR 22
1756-ENBT 23
D 1756-EWEB 23
device type 11 dual-port 25
dual-port module 25 single-port 24

E V
electronic keying 11 vendor 11
changing parameters 11
disable keying 11
EtherNet/IP 7
communication modules 9
connect to network 17
control system 8
EtherNet/IP network
module features 10
specifications 10

I
IP Address
factory default 19
requirements 18
rotary switches 18
set the IP address 18

M
major revision 11
minor revision 11

N
network
specifications 10

P
product code 11
protected mode 12
disabling 12
enabling explicit protected mode 12
operation in explicit protected mode 12

Rockwell Automation Publication 1756-UM004A-EN-P - March 2019 29

Index

Notes:

30 Rockwell Automation Publication 1756-UM004A-EN-P - March 2019

.

Rockwell Automation Support

Use the following resources to access support information.

Technical Support Center Knowledgebase Articles, How-to Videos, FAQs, Chat, User https://rockwellautomation.custhelp.com/
Forums, and Product Notification Updates.
Local Technical Support Phone Numbers Locate the phone number for your country. http://www.rockwellautomation.com/global/support/get-support-now.page
Find the Direct Dial Code for your product. Use the code to
Direct Dial Codes route your call directly to a technical support engineer. http://www.rockwellautomation.com/global/support/direct-dial.page

Installation Instructions, Manuals, Brochures, and

Literature Library http://www.rockwellautomation.com/global/literature-library/overview.page
Technical Data.
Product Compatibility and Download Get help determining how products interact, check
http://www.rockwellautomation.com/global/support/pcdc.page
Center (PCDC) features and capabilities, and find associated firmware.

Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete the
How Are We Doing? form at http://literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.

Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Allen-Bradley, Compact 5000, ControlFLASH Plus, CompactLogix, ControlLogix, FactoryTalk, FLEX 5000, Logix 5000, PanelView, PowerFlex, Rockwell Software, Rockwell Automation, and Stratix are trademarks of Rockwell Automation,
Inc.
CIP, DeviceNet, and EtherNet/IP are trademarks of ODVA, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Publication 1756-UM004A-EN-P - March 2019

Copyright © 2019 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.