Scribd
Upload
35K views5 pages

Auto Data 3.45 INSTALLATION INSTRUCTIONS

This document provides installation instructions for Autodata software in 7 steps: 1) Run the Installer, 2) Follow on-screen prompts and restart, 3) Generate a UID number, 4) Use the UID to generate a license file, 5) Run the license file, 6) Install additional drivers, 7) Run Autodata. It also notes that running as Administrator is important and provides troubleshooting steps to check device drivers and regional settings if errors occur.

Uploaded by

Manuel Alarcon
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
35K views5 pages

Auto Data 3.45 INSTALLATION INSTRUCTIONS

This document provides installation instructions for Autodata software in 7 steps: 1) Run the Installer, 2) Follow on-screen prompts and restart, 3) Generate a UID number, 4) Use the UID to generate a license file, 5) Run the license file, 6) Install additional drivers, 7) Run Autodata. It also notes that running as Administrator is important and provides troubleshooting steps to check device drivers and regional settings if errors occur.

Uploaded by

Manuel Alarcon
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 5

AUTODATA INSTALLATION INSTRUCTIONS:

1. Run "Install_x86" or "Install_x64" as Administrator depending on your OS (32 or 64 bit)

2. Follow on console screen messages and wait for the installation to complete,You will then be
prompted to restart your computer.After the restart is complete, the test mode will appear in the
lower right corner of your computer screen. If the test mode does not appear, you may need to
use a virtual machine to install this software (generally only win10home version will not appear)

3) Open "Keygen" folder and Run "GetUid-x86" or "GetUid-x64" as Administrator (<<< this is
important) depending on your OS (32 or 64 bit)
You will get 8-digit numbers (32-bit systems) or 10-digit numbers (64-bit systems),This is your
computer's UID

4) Now because you have your UID number, you can run "keygen.cmd" and paste/enter UID to
generate "license.reg" registry file (it's important to NOT enter first 2 digits which are probably
64, enter ONLY last 8 digits,For example UID is 6485956hj, you just need to enter 85956hj)
(in case your UID is 6400000000 you must restart/reboot your PC and go back to step 3 because
that UID is NOT proper and valid)

5) Run new generated registry file named "license.reg"

6) run Start Emulator


Then he will install SentinelDriver by himself, or prompt you to install SentinelDriver now, you can
accept it.

7) run Autodata 3.45 as Administrator from desktop shortcut or ofcourse C:\ADCDA2\ADBCD.exe

8) Enjoy!

=========================================================================

*IMPORTANT* BEFORE YOU BEGIN READ THIS NOTES:


- Run as Administrator is very important where it says "(<<< this is important)"!
- Every restart/reboot is MUST and IMPORTANT for Windows 7/8/8.1/10 but NOT for XP!
- If you get error on Autodata starting like in picture included in this package, you'll need to
change your Regional settings to English US!
- If you get any kind of error trying to start Autodata, go to "RegSettings" folder and first run
"DeleteRegSettings.reg" then "RegSettings_x86.reg" or "RegSettings_x64.reg" depending on your
OS (32 or 64 bit)!

=========================================================================
A1.If you get this error, it is because your SentinelDriver is not installed.

You can check In “Device Manager: must be “SafeNet Sentinel Hardware Key”，If
you don't have this, it means that your license.reg was not made successfully, you
can go back to step 3 and reinstall it again.
and you must have in “System Device ”AuDaS0 Virtual Device”
or”nodongle.biz”，If it is with an exclamation mark, then you can manually install
Emulator_x64 or Emulator_x86 yourself

A2.If you get error on Autodata starting like in picture included in this package, you'll need to
change your Regional settings to English （US）!

A3.If you get any kind of error trying to start Autodata, go to "RegSettings" folder and first run
"DeleteRegSettings.reg" then "RegSettings_x86.reg" or "RegSettings_x64.reg" depending on your
OS (32 or 64 bit)!

You might also like