Aashto Bridge Design (LRFD) Manual

Bridge Design Manual - LRFD
Revised December 2011

© 2011 by Texas Department of Transportation
(512) 302-2453 all rights reserved
Manual Notice 2011-1
From: Gregg A. Freeby, P.E., Director, Bridge Division
Manual: Bridge Design Manual - LRFD
Effective Date: December 22, 2011
Purpose
This manual documents policy on bridge design in Texas. It assists Texas bridge designers in apply-
ing provisions documented in the AASHTO LRFD Bridge Design Specifications, to which
designers should adhere unless directed otherwise by this document.
Changes
Revisions to manual to add information in Chapter 3 regarding Concrete Deck Slabs on Spread Box
Beams (X-Beams) and Prestressed Concrete Spread Box Beams (X-Beams); minor revisions in
various chapters to reference current editions of publications.
Contact
For more information about any portion of this manual, please contact the Design Section of the
Bridge Division.
Archives
Past manual notices are available in a PDF archive.

Table of Contents
Chapter 1 — About this Manual
Section 1 — Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
Chapter 2 — Limit States and Loads

Section 1 — Limit States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Limit States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Section 2 — Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Live Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Braking Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Vehicular Collision Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Earthquake Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Vessel Collision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Chapter 3 — Superstructure Design

Section 1 — Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Section 2 — Concrete Deck Slabs on Stringers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Geometric Constraints. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Detailing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Section 3 — Concrete Deck Slabs on U Beams (U40 and U54). . . . . . . . . . . . . . . . . . . . . . .3-5
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Detailing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
Section 4 — Concrete Deck Slabs on Slab Box Beams (X-Beams) . . . . . .3-7
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
Detailing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8
Section 5 — Concrete Deck Slabs on Slab Beams, Double-Tee Beams, and Box Beams . . .3-9
Bridge Design Manual - LRFD i TxDOT 12/2011

Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Detailing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Section 6 — Prestressed Concrete I Beams and I Girders. . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Geometric Constraints. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Structural Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Section 7 — Prestressed Concrete U Beams (Types U40 and U54) . . . . . . . . . . . . . . . . . . .3-17
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18
Detailing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19
Section 8 — Prestressed Concrete Slab Beams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-21
Section 9 — Prestressed Concrete Decked Slab Beams . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23
Section 10 — Prestressed Concrete Double-Tee Beams. . . . . . . . . . . . . . . . . . . . . . . . . . . .3-24
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-24
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-25
Section 11 — Prestressed Concrete Box Beams (Types B20, B28, B34, and B40) . . . . . . .3-26
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-26
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-27
Section 12 — Prestressed Concrete Spread Box Beams (X-Beams) . . . .3-29
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-29
Bridge Design Manual - LRFD ii TxDOT 12/2011

Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-30
Section 13 — Cast-in-Place Concrete Slab and Girder Spans (Pan Forms) . . . . . . . . . . . . .3-32
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-32
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-32
Section 14 — Cast-in-Place Concrete Slab Spans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-33
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-33
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-34
Section 15 — Straight Plate Girders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-35
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-35
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-36
Section 16 — Curved Plate Girders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-38
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-38
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-38
Chapter 4 — Substructure Design

Section 1 — Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Section 2 — Foundations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Section 3 — Abutment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Section 4 — Rectangular Reinforced Concrete Bent Caps . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Structural Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Detailing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
Section 5 — Inverted Tee Reinforced Concrete Bent Caps . . . . . . . . . . . . . . . . . . . . . . . . . .4-9
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9
Bridge Design Manual - LRFD iii TxDOT 12/2011

Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9
Detailing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
Section 6 — Columns for Multi-Column Bents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12
Chapter 5 — Other Designs

Section 1 — Widenings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Design Recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Section 2 — Steel-Reinforced Elastomeric Bearings for Prestressed Concrete Beams . . . . .5-3
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
Detailing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Section 3 — Strut-and-Tie Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Section 4 — Corrosion Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
Guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
Bridge Design Manual - LRFD iv TxDOT 12/2011

Chapter 1 — About this Manual
Contents:
Section 1 — Introduction
Bridge Design Manual - LRFD 1-1 TxDOT 12/2011

Chapter 1 — About this Manual Section 1 — Introduction
Section 1 — Introduction
Implementation
Load and Resistance Factor Design (LRFD) is a design methodology that makes use of load and
resistance factors based on the known variability of applied loads and material properties. In 1994,
the American Association of State Highway and Transportation Officials (AASHTO) published the
first AASHTO Load and Resistance Factor Bridge Design Specifications. The Federal Highway
Administration (FHWA) mandated the use of LRFD for all bridges for which the Texas Department
of Transportation (TxDOT) initiated preliminary engineering after October 2007.
Purpose
This manual documents policy on bridge design in Texas. It assists Texas bridge designers in apply-
ing provisions documented in the AASHTO LRFD Bridge Design Specifications, 5th edition, with
2010 interim revisions, which designers should adhere to unless directed otherwise by
this document. Recommendations and examples are available on the TxDOT web site at http://
www.txdot.gov/business/contractors_consultants/bridge/default.htm.
Updates
Updates to this manual are summarized in the following table.

Manual Revision History
Version Publication Date Summary of Changes
2005-1 July 2005 New manual
2005-2 September 2005 Revision adding information on deck slabs on slab beams, double-
tee beams, and box beams. Also added information on prestressed
slab beams, prestressed concrete double-tee beams, prestressed con-
crete box beams, and cast-in-place concrete slab and girder spans
(pan forms).
2006-1 June 2006 Revision adding information on cast-in-place concrete spans,

straight plate girders, and curved plate girders.
2006-2 July 2006 Revision adding information in Chapter 3 on prestressed concrete U

beams (types U40 and U54) and on concrete deck slabs on U beams
(types U40 and U54), and making minor adjustments to references in
the Chapter 3 section on geometric constraints for steel-reinforced
elastomeric bearings and to the Chapter 4 sections on design criteria
for abutments and design criteria for inverted tee reinforced concrete
bent caps.

Manual Revision History
Version Publication Date Summary of Changes
2007-1 April 2007 Revisions to the design criteria for concrete deck slabs on stringers,
cast-in-place concrete slab spans, rectangular reinforced concrete
bent caps and inverted tee reinforced concrete bent caps. Revisions
to the structural analysis of prestressed concrete I beams, U beams,
slab beams and box beams (Types B20, B28, B34 and B40). Revi-
sions to the geometric constraints for abutment and rectangular
reinforced concrete bent caps. Revisions to the design recommenda-
tions for widenings.
2008-1 April 2008 Revisions to manual to conform with the 4th Edition of the AASHTO
LRFD Bridge Design Specifications. Adds information in Chapter 5
for strut-and-tie design method. Revision to requirements for foun-
dation load calculations. Revision to interface shear transfer
requirements for prestressed beams. Clarifies policy on live load dis-
tribution factors for beam design. Revision to policy on debonding
design. Corrects inverted tee design formulas.
2009-1 May 2009 Revisions to the manual to revise policy on foundation load calcula-
tions; revises policy on live load deflection check; revises policy on
use of empirical design method for slab design; updates prestressed
concrete design criteria; revises debonding limits for prestressed
concrete design; adds requirements for considering corrosion protec-
tion measures; clarifies policy on bearing pad design; revises policy
on calculating live load distribution factors for double-tee beams;
and corrects minor editorial errors.
2010-1 September 2010 Revisions to the manual to revise policy on concrete deck slabs on
stringers, minimum shear reinforcing for inverted tee bent caps and
steel-reinforced elastomeric bearings.
2011-1 December 2011 Revisions to manual to update information in

Chapter 2 regarding earthquake effects; add
information in Chapter 3 regarding Concrete
Deck Slabs on Spread Box Beams (X-Beams) and
Prestressed Concrete Spread Box Beams (X-
Beams); minor revisions in various chapters to
reference current editions of publications.
Organization
 The information in this manual is organized as follows:
 Chapter 1, About this Manual. Introductory information on the purpose and organization of the
manual.
 Chapter 2, Limit States and Loads. General information on limit states and on load factors.
 Chapter 3, Superstructure Design. Policy on LRFD design of specific bridge superstructure
components.

 Chapter 4, Substructure Design. Policy on LRFD design of specific bridge substructure

components.
 Chapter 5, Other Designs. Design guidelines for bridge widenings and steel-reinforced elasto-
meric bearings for prestressed concrete beams and strut-and-tie method. This chapter also
addresses corrosion protection measures.
Feedback
Direct any questions or comments on the content of the manual to the Director of the Bridge Divi-
sion, Texas Department of Transportation.

Chapter 2 — Limit States and Loads
Contents:
Section 1 — Limit States
Section 2 — Loads

Chapter 2 — Limit States and Loads Section 1 — Limit States
Section 1 — Limit States
Limit States
Classify all bridge designs as typical bridges when applying the operational importance factor, η I ,
to strength limit states. Use η I = 1.0 for all limit states. See AASHTO LRFD Bridge Design Speci-
fications, Article 1.3.5.
Provisions under Extreme Event I need not be considered except for regions near Big Bend.
Provisions under Extreme Event II must be considered only when vehicular collision or vessel col-
lision evaluation is required.
For typical multi-column bridges, determine design loads for foundations at Service Limit State I.
Foundation loads for single column bents and other non-typical substructures should be determined
by Service Limit State I and Service Limit State IV. For Service Limit State IV, include the vertical
wind pressure as specified in Article 3.8.2. For foundation loads on typical multi-column bents and
abutments, use the multiple presence factor, m, per AASHTO LRFD Bridge Design Specifications,
Article 3.6.1.1.2. Distribute the live load equally to all supporting foundations, assuming all lanes
are loaded.
Follow the procedures described in the TxDOT Geotechnical Manual, which is available on the
internet at ftp://ftp.dot.state.tx.us/pub/txdot-info/gsd/manuals/geo.pdf, to determine the size and
length of foundations.
Check live load deflection using AASHTO LRFD Bridge Design Specifications, Articles 2.5.2.6.2
and 3.6.1.3.2. Ensure that the calculated deflection does not exceed Span/800 using a live load dis-
tribution factor equal to number of lanes divided by number of girders. If the bridge has pedestrian
sidewalks, the deflection limit is Span/1000.

Chapter 2 — Limit States and Loads Section 2 — Loads
Section 2 — Loads
Live Loads
Use HL93 design live load as described in Article 3.6.1.2 of the AASHTO LRFD Bridge Design
Specifications unless design for a special vehicle is specified or warranted.
Design widenings for existing structures using HL93. Rate existing structures using AASHTO Stan-
dard Specifications and HS20 loading. Show load rating and design loads on the bridge plan, for
example, HS20 (Existing) HL93 (New).
Do not use the reduction in the multiple presence factor (m) based on Average Daily Truck Traffic
(ADTT) on the bridge as suggested in the AASHTO LRFD Bridge Design Specifications under
commentary on Article 3.6.1.1.2, Multiple Presence of Live Load.
For simple-span bridges, do not apply the provisions for two design trucks as described in Article
3.6.1.3.1 of the AASHTO LRFD Bridge Design Specifications.
Disregard recommendations to investigate negative moment and reactions at interior supports for
pairs of the design tandem provided in the commentary provided in the AASHTO LRFD Bridge
Design Specifications under Article 3.6.1.3.1, Application of Design Vehicular Live Loads.
Braking Force
Take the braking force, BR, as 5% of the design truck plus lane load or 5% of the design tandem
plus lane load. See Article 3.6.4 in the AASHTO LRFD Bridge Design Specifications.
Vehicular Collision Force
See Article 3.6.5 in the AASHTO LRFD Bridge Design Specifications. Ongoing TxDOT-sponsored
research supports the following policy:
Abutments and retaining walls—Due to the soil behind abutments and retaining walls, the collision
force in Article 3.6.5 need not be considered.
Bents—Bents adjacent to roadways with design speeds of 50 mph or less need not meet the require-
ments of Article 3.6.5. Bents adjacent to roadways with design speeds greater than 50 mph and
located within 30 feet of the edge of roadway (defined as edge of lane nearest the column) must
meet at least one of the following requirements:
Protect with an approved barrier. The Bridge Division can provide details of acceptable barriers.

Design for 400-kip load. Use a high collision strut between the columns if necessary
Validate that the structure will not collapse by analyzing the structure considering removal of any
single column. Analyze using Extreme Event II Limit State. Use 1.25 load factor for all dead loads
and 0.5 load factor for live load. Consider live load only on the permanent travel lanes, not the
shoulder lanes.
Special considerations include the following:

 Single-column bents—Generally single-column bents have sufficient mass and will meet the
requirements of Article 3.6.5. No further analysis is required for columns with a gross cross-
sectional area in excess of 20 sq. ft. and a least dimension of no less than 3 ft.
For structures within 50 ft. of the center line of a railway track, meet the requirements of AREMA
or the governing railroad company.
Earthquake Effects
Except as noted below, bridges and structures in Texas do not

require analysis for seismic loading due to the low seismic hazard
as shown in AASHTO 3.10.2.
The TxDOT Bridge Standards and conventional bridge configurations

have been evaluated for seismic effects and do not require further
analysis.
For conventional structures with superstructure unit lengths or

interior bent "H" heights outside of the limits stated in the TxDOT
Bridge Standards and which are located in Brewster, Presidio, Jeff
Davis, Culberson, Hudspeth and El Paso counties, check Minimum
Support Length Requirements outlined in AASHTO 4.7.4.4.
Non-conventional or exotic bridges do not require seismic evalua-

tion, except those located in Brewster, Presidio, Jeff Davis,
Culberson, Hudspeth and El Paso counties. In these locations,
evaluate the structure for earthquake effects as required by AAS-
HTO LRFD 3.10. Contact the TxDOT Bridge Division for guidance.
Vessel Collision
TxDOT requires that all bridges crossing waterways with documented commercial vessel traffic
comply with AASHTO LRFD Bridge Design Specifications, Article 3.14. For widening of existing
structures, at least maintain the current strength of the structure relative to possible vessel impact,

and increase the resistance of the structure where indicated if possible. Consult the TxDOT Bridge
Division for assistance interpreting and applying these design requirements.

Chapter 3 — Superstructure Design
Contents:
Section 1 — Overview
Section 2 — Concrete Deck Slabs on Stringers
Section 3 — Concrete Deck Slabs on U Beams (U40 and U54)
Section 4 — Concrete Deck Slabs on Slab Box Beams (X-Beams)
Section 6 — Prestressed Concrete I Beams and I Girders
Section 7 — Prestressed Concrete U Beams (Types U40 and U54)
Section 8 — Prestressed Concrete Slab Beams
Section 9 — Prestressed Concrete Decked Slab Beams
Section 10 — Prestressed Concrete Double-Tee Beams
Section 11 — Prestressed Concrete Box Beams (Types B20, B28, B34, and B40)
Section 13 — Cast-in-Place Concrete Slab and Girder Spans (Pan Forms)
Section 14 — Cast-in-Place Concrete Slab Spans
Section 15 — Straight Plate Girders
Section 16 — Curved Plate Girders

Chapter 3 — Superstructure Design Section 1 — Overview
Introduction
This chapter documents policy on Load and Resistance Factor Design (LRFD) of specific bridge
superstructure components.

Chapter 3 — Superstructure Design Section 2 — Concrete Deck Slabs on Stringers
Section 2 — Concrete Deck Slabs on Stringers
Materials
'
Use Class S concrete ( f c = 4.0 ksi). If the deck will be subjected regularly to deicing agents based
on district policy, use Class S (HPC) concrete.
Use Grade 60 reinforcing steel. Use uncoated reinforcing steel unless the deck will be subjected
regularly to de-icing agents based on district policy, in which case use epoxy-coated reinforcing
steel.
Waterproof deck slabs with one of the two classes of treatment specified in Item 428, “Concrete
Surface Treatment,” of the Texas Standard Specifications.
Geometric Constraints
TxDOT standard deck slabs are 8 in. and 8.5 in. with top clear cover of 2 in. and 2.5 in. respec-
tively. Use the 8.5-in deck slab for bridges where regular use of deicing agents is anticipated. Both
deck slabs use 1.25-in. bottom clear cover.
Reinforce standard deck slabs as shown in Chapter 5 of the Bridge Detailing Manual, available at
http://crossroads/org/gsd/books/det/index.htm.
Design Criteria
For prestressed concrete I beams and steel beams with standard deck slabs, use the following beam
spacing and overhang width limits:
 Maximum clear span (or distance between flange quarter points of steel beams) is 8.667 ft. If
permitting use of prestressed concrete panels, ensure clear span is acceptable based on limits
shown on standard drawing PCP.
 Typical overhang is 3.0 ft. measured from the center line of the beam to the edge of the slab.
 Maximum overhang measured from edge of slab to face of beam top flange (or steel beam
flange quarter point) is the lesser of 3.917 ft. or 1.3 times the depth of beam, which prevents
excessive torsion on fascia beams during slab placement. At span ends, reduce the limit from
3.917 ft. to 3.083 ft. to account for reduced wheel load distribution.
 Minimum overhang is 0.5 ft. measured from edge of slab to face of beam top flange to allow
sufficient room for the slab drip bead.
For TxGirders limit overhang widths as follows:

Chapter 3 — Superstructure Design Section 2 — Concrete Deck Slabs on Stringers
 For Tx 28 and Tx34, 4.0 ft.

 For Tx 40, Tx 46 and Tx 54, 4.5 ft.
 For Tx 62 and Tx 72, 4.75 ft.
Due to the additional reinforcement in overhangs with the thickened slab ends provided for
TxGirders, no reduction in overhang limits is necessary at span ends.
Do not use the empirical design method specified in Article 9.7.2 of the AASHTO LRFD Bridge
Design Specifications. Use the Traditional Design method specified in Article 9.7.3 of the AAS-
HTO LRFD Bridge Design Specifications.
Place main reinforcing steel parallel to the skew up to 15 degree skews. Place reinforcing steel per-
pendicular to beams for skews more than 15 degrees, and use corner breaks. Provide at least #5’s at
6 inches for main reinforcement.
Overhang strength for extreme events, described in Article 9.5.5 of the AASHTO LRFD Bridge
Design Specifications, is satisfied through TxDOT’s rail crash testing.
When calculating the cracking moment of a member in accordance with Article 5.7.3.3.2, take the-
modulus of rupture, f r , as 0.24 f c' , for all normal weight concrete.
Use Class 2 exposure conditions for crack control in accordance with Article 5.7.3.4.
Detailing
In overhangs, use a 3-in. space between outermost Bars D to minimize slab damage from rail
impacts. Space Bars T at 9 in. to provide better crack control at construction joints, precast panel
ends, and control joints placed at interior bent locations with continuous slab/simple span
construction.
The deck slab must be at least 8 inches thick or 8.5 inches thick when deicing chemicals are used.

Chapter 3 — Superstructure Design Section 3 — Concrete Deck Slabs on U Beams (U40
and U54)
Section 3 — Concrete Deck Slabs on U Beams (U40 and U54)
Materials
'
Use Class S concrete ( fc = 4.0 ksi). If the deck will be subjected regularly to deicing agents based
steel.
Surface Treatment,” of the TxDOT Standard Specifications.
Reinforce the cast-in-place portion of the slab with #5 bars spaced at 6 in. in the transverse direc-
tion and #4 bars spaced at 9 in. in the longitudinal direction
Design Criteria
With standard deck slabs, use the following beam spacing and overhang width limits:
 Maximum clear span is 8.583 ft. If permitting use of prestressed concrete panels, ensure clear
span is acceptable based on limits shown on standard drawing PCP.
 Typical overhang is 6.750 ft. measured from the center line of the bottom of the exterior beam
to the edge of the slab.
 Maximum overhang is 3.917 ft. measured from slab edge to beam flange edge. At span ends,
reduce the 3.917-ft. limit to 3.083 ft. to account for reduced wheel load distribution.
 Minimum overhang is 0.5 ft. measured from slab edge to beam top flange edge to allow suffi-
cient room for the slab drip bead.
 For overhangs (measured from the centerline of the outside beam to the edge of the slab) in
excess of 7.250 ft., check the outside web-to-bottom flange joint of the exterior beam for ade-
quacy under construction loads.

Chapter 3 — Superstructure Design Section 3 — Concrete Deck Slabs on U Beams (U40
and U54)
Design Specifications. Use the Traditional Design method specified in Article 9.7.3 of the AAS-
HTO LRFD Bridge Design Specifications.
pendicular to beams for skews more than 15 degrees, and use corner breaks.
Design Specifications, is satisfied through TxDOT’s rail crash testing.
When calculating the cracking moment of a member in accordance with Article 5.7.3.3.2, take the
modulus of rupture, f r , as 0.24 f c' for all normal weight concrete.
Detailing
construction.

Chapter 3 — Superstructure Design Section 4 — Concrete Deck Slabs on Slab
Box Beams (X-Beams)
Section 4 — Concrete Deck Slabs on Slab Box Beams (X-Beams)
Materials
'
Use Class S concrete ( fc = 4.0 ksi). If the deck will be subjected regularly to deicing agents based
steel.
Surface Treatment,” of the TxDOT Standard Specifications.
Reinforce standard deck slabs as shown in Chapter 5 of the Bridge Detailing Manual, available at
http://onlinemanuals.txdot.gov/txdotmanuals/det/index.htm.
Design Criteria
With standard deck slabs, use the following beam spacing and overhang width limits:
 Maximum clear span is 8.667 ft. If permitting use of prestressed concrete panels, ensure clear
span is acceptable based on limits shown on standard drawing PCP.
 Typical overhang, measured from the center line of the bottom of the exterior beam to the edge
of the slab, is 4.0 ft. for a 5XB beam and 3.5 ft. for a 4XB beam.
 Maximum overhang is 3.917 ft. measured from slab edge to beam flange edge. At span ends,
reduce the 3.917-ft. limit to 3.083 ft. to account for reduced wheel load distribution.
 Minimum overhang is 0.5 ft. measured from slab edge to beam top flange edge to allow suffi-
cient room for the slab drip bead.
Design Specifications. Use the Traditional Design method specified in Article 9.7.3 of the AASHTO
LRFD Bridge Design Specifications.

Chapter 3 — Superstructure Design Section 4 — Concrete Deck Slabs on Slab
Box Beams (X-Beams)
pendicular to beams for skews more than 15 degrees, and use corner breaks.
Design Specifications, is satisfied through TxDOT's rail crash testing.
modulus of rupture, f r , as 0.24 f c' for all normal weight concrete.
Detailing
construction.

Chapter 3 — Superstructure Design Section 5 — Concrete Deck Slabs on Slab Beams,
Double-Tee Beams, and Box Beams
Section 5 — Concrete Deck Slabs on Slab Beams, Double-Tee Beams, and Box Beams
Materials
'
Use Class S concrete ( fc = 4.0 ksi). If the slab will be subjected regularly to deicing agents based
Use Grade 60 reinforcing steel. Use uncoated reinforcing steel unless the slab will be subjected reg-
ularly to de-icing agents based on district policy, in which case use epoxy-coated reinforcing steel.
Waterproof slabs with one of the two classes of treatment specified in Item 428, “Concrete Surface
Treatment.”
TxDOT standard composite concrete slabs are 5 in. thick, minimum.
Use 2-in. top clear cover. If the slab will be subjected regularly to deicing agents based on district
policy, use 2.5-in. top clear cover. No increase in slab thickness is required.
Design Criteria
For transverse reinforcement, use #5 bars spaced at 6-in. maximum for double-tee and slab beam
bridges and #4 bars spaced at 6 in. maximum for box beam bridges.
For longitudinal reinforcement, use #4 bars spaced at 12 in. maximum.
Detailing
Use controlled joints at bent centerlines when the slab is continuous over bents.

Chapter 3 — Superstructure Design Section 6 — Prestressed Concrete I Beams and I
Girders
Section 6 — Prestressed Concrete I Beams and I Girders
Materials
fci' '
Use Class H concrete with a minimum = 4.0 ksi and fc = 5.0 ksi.
Design beams for 0.5-in. low-relaxation strands. You may use 0.6-in. low-relaxation strands as nec-
essary but should check its availability with fabricators.
Use prestressing strand with a specified tensile strength, fpu, of 270 ksi.
Intermediate diaphragms are not required for structural performance. Do not use intermediate dia-
phragms unless required for erection stability of beam sizes stretched beyond their normal span
limits.
Structural Analysis
Beam designs must meet the following requirements:

 Distribute the weight of one railing to no more than three beams, applied to the composite
cross section.
 Use section properties given on the standard drawings.
 Composite section properties may be calculated assuming the beam and slab to have the same
'
modulus of elasticity (for beams with fc < 8.5 ksi). Do not include haunch concrete placed on
top of the beam when determining section properties. Section properties based on final beam
and slab modulus of elasticity may also be used, however, this design assumption must be
noted on the plans.
 Live load distribution factors must conform to AASHTO LRFD Bridge Design Specifications,
Article 4.6.2.2.2 for flexural moment and Article 4.6.2.2.3 for shear, except as noted below:
 For exterior beam design with a slab cantilever length equal to or less than one-half of the adja-
cent interior beam spacing, treat the exterior beam as if it were an
interior beam to determine the live load distribution factor for the interior beam.
The slab cantilever length is defined as the distance from the center line of the exterior beam to
the edge of the slab.
 For exterior beam design with a slab cantilever length exceeding one-half of the adjacent inte-
rior beam spacing, use the lever rule with the multiple presence factor of 1.0 for single lane to
determine the live load distribution.

Girders
 The live load used to design the exterior beam must never be less than the live load used to
design an interior beam of comparable length.
 Do not use the special analysis based on conventional approximation for loads on piles per
AASHTO LRFD Bridge Design Specifications, Article C4.6.2.2.2d, unless the effectiveness of
diaphragms on the lateral distribution of truck loads is investigated.
 For interior as well as exterior girders, do not take the live load distribution factor, for moment
or shear, as less than
m × NL
Nb
Where,
m = multiple presence factor per AASHTO LRFD 3.6.1.1.2
N L = number of lanes
Nb = number of beams or girders
 When precast concrete deck panels or stay-in-place metal forms are allowed, design the beam
using the basic slab thickness.
 When calculating the cracking moment of a member in accordance with Article 5.7.3.3.2, take
the modulus of rupture f r , as 0.24 f c' , for all normal weight concrete.
Design Criteria
Standard beam designs must meet the following requirements:

 Strands should be added and depressed in the order shown on the IBND standard drawing for I
beams and IGND for I girders, available at http://www.txdot.gov/insdtdot/orgchart/cmd/
cserve/standard/bridge-e.htm.
 Use hold-down points shown on the IBD standard drawing for I beams and IGND for I girders,
available at http://www.txdot.gov/insdtdot/orgchart/cmd/cserve/standard/bridge-e.htm.
 Strand stress after seating of chucks is not greater than 0.75 fpu for low-relaxation strands.
'
 Initial tension in the amount of 0.24 f c (ksi) is allowed. Based on TxDOT experience, addi-
tional bonded reinforcement is not required.
 Initial compression in the amount of 0.65 fci' (ksi) is allowed.
 Final stress at the bottom of beam ends need not be checked except when straight debonded
strands are used or when the effect of the transfer length of the prestressing strand is consid-
ered in the analysis.
'
 Final tension in the amount of 0.19 f c (ksi) is allowed.

Girders
 The required final concrete strength ( fc' ) is typically based on compressive stresses, which
must not exceed the following limits:
'
 0.60 fc for stresses due to total load plus prestress.
 0.45 fc' for stresses due to effective prestress plus permanent (dead) loads.
 0.40 fc' for stresses due to live loads plus one-half of the sum of stresses due to prestress
and permanent (dead) loads.
 Tension in the amount of 0.24 f c' is allowed for checking concrete stresses during deck and
diaphragm placement.
 Use an effective strand stress after release of 0.75 f pu − Δ f pES − Δf pR1 .
 The end position of depressed strands should be as low as possible so that the position of the
strands does not control the release strength. Release strength will occasionally be controlled
by end conditions when the depressed strands have been raised to their highest possible
position.
 Do not use the simplified procedure for determining shear resistance as allowed by AASHTO
LRFD 5.8.3.4.3. Use the General Procedure as provided by AASHTO LRFD 5.8.3.4.2. Do
not use provisions of Appendix B of the AASHTO LRFD Bridge Design Specifications.
 Calculate required stirrup spacing for #4 Grade 60 bars according to the AASHTO LRFD
Bridge Design Specifications, Article 5.8. Change stirrup spacing as shown on IBD standard
drawing for I beams and IGND for I girders, available at http://www.txdot.gov/insdtdot/
orgchart/cmd/cserve/standard/bridge-e.htm, only if analysis indicates the inadequacy of the
standard design.
 Replace AASHTO LRFD equation 5.8.4.2-1 with the following:
Vu1Qslab
Vui =
Igbvi
Where Q slab is the first moment of the area of the slab with respect to the neutral axis of the
composite section.
Take bvi, width of the interface, equal to the beam top flange width. Do not reduce bvi to
account for precast panel bedding strips.
 Determine interface shear transfer in accordance with AASHTO LRFD 5.8.4. Take Cohesion
and Friction Factors as provided in AASHTO LRFD Article 5.8.4.3 as follows:
c = 0.28 ksi
= 1.0
K 1 = 0.3
K 2 = 1.8 ksi
 Replace AASHTO LRFD equation 5.4.2.3.2-2 with the following:

Girders
k s = 1.45 - 0.13 (V/S) > 0.0

 Compute deflections due to slab weight and composite dead loads assuming the beam and slab
to have the same modulus of elasticity. Assume E c = 5,000 ksi for beams with fc' < 8.5 ksi.
Predicted slab deflections should be shown on the plans although field experience indicates
actual deflections are generally less than predicted. Use the deflection due to slab weight only
times 0.8 for calculating haunch depth.
 TxDOT standard I beams and I girders reinforced as shown on the IBD and IGD standard
drawings are adequate for the AASHTO LRFD Bridge Design Specifications requirements of
Article 5.10.10.
 A calculated positive (upward) camber is required after application of all permanent (dead)
loads.
When calculating prestress losses, use AASHTO LRFD Bridge Design Specifications 2004, 3rd.
Ed., Article 5.9.5 Loss of Prestress. In the absence of AASHTO LRFD Bridge Design Specifica-
tions 2004, use AASHTO LRFD Bridge Design Specifications 2010, 5th Ed., Article 5.9.5 Loss
of Prestress with the following changes.
 Replace AASHTO LRFD (2010) Eq. 5.9.5.1-1 with the following:
Δf pT = Δf pES + Δf pSR + Δf pCR + Δf pR2
 Replace AASHTO LRFD (2010) Eq. 5.9.5.1-2 with the following:
Δf pT = Δf pF + Δf pA + Δf pES + Δf pSR + Δf pCR + Δ f pR2
Where,
Δf pT = total loss (ksi)
Δf pF = loss due to friction (ksi)
Δf pA = loss due to anchorage set (ksi)
Δf pES = loss due to elastic shortening (ksi)
Δf pSR = loss due to shrinkage (ksi)
Δf pCR = loss due to creep of concrete (ksi)
Δf pR 2 = loss due to relaxation of steel after transfer (ksi)
 Add the following to AASHTO LRFD (2010) Article 5.9.5.1:
"In pretensioned members, where the approximate lump sum estimate of losses specified in
Article 5.9.5.3 is used, the part of the loss due to relaxation occuring before transfer, Δf pR1 ,
should be deducted from the total relaxation.
For post-tensioned members, consideration should be given to a loss of tendon force, as indi-
cated by pressure readings, within the stressing equipment."

Girders
 In the AASHTO LRFD (2007) Eq. 5.9.5.2.3a-1, replace Ect with Eci where Eci = modulus of
elasticity of concrete at transfer (ksi).
 Add the following to AASHTO LRFD (2007) Article 5.9.5.2.3a:
"For pretensioned components of usual design, fcgp may be calculated on the basis of a pre-
stressing steel stress assumed to be 0.65 fpu for stress-relieved strand and high-strength bars
and 0.70 fpu for low relaxation strand.
For components of unusual design, more accurate methods supported by research or experi-
ence should be used."
 Disregard all commentary in AASHTO LRFD (2010) Article C5.9.5.2.3a until Equation
C5.9.5.2.3a-1.
 Disregard AASHTO LRFD (2010) Equation 5.9.5.3-1.
For low relaxation strands, the values for I-beams and I-girders in AASHTO LRFD Table
5.9.5.3-1 may be reduced by 6.0 ksi.
 Add the following to AASHTO LRFD (2010) Table 5.9.5.3-1:
For Wires and Strands with For Bars with

Type of Beam Section Level fpu = 235, 250 or 270 ksi fpu = 145 or 160ksi
I-Girder Average
 f ' − 6.0  19 . 0 + 6 .0 PPR
33. 01.0 − 0. 15 c  + 6. 0PPR
 6. 0 
 Replace AASHTO LRFD (2007) Article 5.9.5.4 with the following:

5.9.5.4 Refined Estimates of Time-Dependent Losses
5.9.5.4.1 General
More accurate values of creep-, shrinkage-, and relaxation-related losses, than those specified
in Article 5.9.5.3 may be determined in accordance with the provisions of this article for pre-
stressed members with:
 Spans not greater than 250 ft.,
 Normal weight concrete, and
 Strength in excess of 3.50 ksi at the time of prestress.
For lightweight concrete, loss of prestress shall be based on the representative properties of the
concrete to be used.
For segmental construction, for all considerations other than preliminary design, prestress
losses shall be determined as specified in Article 5.9.5, including consideration of the time-
dependent construction method and schedule shown in the contract documents.
5.9.5.4.2 Shrinkage

Girders
Loss of prestress, in ksi, due to shrinkage may be taken as:

 For pretensioned members:
Δf pSR = (17.0 − 0. 150 H ) (5.9.5.4.2-1)
 For post-tensioned members:
Δf pSR = (13.5 − 0. 123H ) (5.9.5.4.2-2)
Where,
H = the average annual ambient relative humidity (percent)
5.9.5.4.3 Creep
Prestress loss due to creep may be taken as:
Δf pCR = 12. 0 f cgp − 7.0Δf cdp ≥ 0 (5.9.5.4.3-1)
Where,
f cgp = concrete stress at center of gravity of prestressing steel at transfer (ksi)
Δf cdp = change in concrete stress at center of gravity of prestressing steel due to permanent
loads, with the exception of the load acting at the time the prestressing force is applied. Values
of Δf cdp should be calculated at the same section or at sections for which f cgp is calculated
(ksi).
5.9.5.4.4 Relaxation
5.9.5.4.4a General
The total relaxation at any time after transfer shall be taken as the sum of the losses specified in
Articles 5.9.5.4.4b and 5.9.5.4.4c.
5.9.5.4.4b At Transfer
In pretensioned members, the relaxation loss in prestressing steel, initially stressed in excess of
0.50 fpu , may be taken as:
 For stress-relieved strand:
log( 24. 0t )  f pj 
Δf pR1 =  − 0. 55 f pj
10.0  f py 
(5.9.5.4.4b-1)
 For low-relaxation strand:
log( 24. 0t )  f pj 
Δf pR1 =  − 0. 55 f pj
40.0  f py 
(5.9.5.4.4b-2)
Where,
t = time estimated in days from stressing to transfer (day)

Girders
f pj = initial stress in the tendon at the end of stressing (ksi)

f py = specified yield strength of prestressing steel (ksi)
5.9.5.4.4c After Transfer
Losses due to relaxation of prestressing steel may be taken as:

 For pretensioning with stress-relieved strands:
Δf pR 2 = 20.0 − 0. 4Δf pES − 0.2(Δf pSR + Δf pCR )
(5.9.5.4.4c-1)
 For post-tensioning with stress-relieved strands:
Δf pR 2 = 20.0 − 0. 3Δ f pF − 0.4Δf pES − 0.2(Δf pSR + Δf pCR )
(5.9.5.4.4c-2)
Where,
Δf pF =the friction loss below the level of 0.70¦pu at the point under consideration, computed
according to Article 5.9.5.2.2 (ksi)
Δf pES =loss due to elastic shortening (ksi)
Δf pSR = loss due to shrinkage (ksi)
Δf pCR = loss due to creep of concrete (ksi)
 For prestressing steels with low relaxation properties conforming to AASHTO M 203
(ASTM A416 or E328):
Use 30 percent of Δf pR 2 given by Eq. 1 or 2.
 For post-tensioning with 145 to 160 ksi bars:
Loss due to relaxation should be based on approved test data. If test data is not available, the
loss may be assumed to be 3.0 ksi.

Chapter 3 — Superstructure Design Section 7 — Prestressed Concrete U Beams (Types
U40 and U54)
Section 7 — Prestressed Concrete U Beams (Types U40 and U54)
Materials
Use Class H concrete with a minimum fci' = 4.0 ksi and fc' = 5.0 ksi.
Design beams for 0.5-in. low-relaxation strands. You may use 0.6-in. low-relaxation strands for
unusual cases but should check its availability with fabricators.
Use prestressing strand with a specified tensile strength fpu, of 270 ksi.
You need not increase section properties of the beam to account for the transformed area of strands
or mild steel.
The maximum skew angle for U-beam bridges is 45 degrees.
Structural Analysis

 Include the overlay at the discretion of the designer or if the bridge will receive the overlay
immediately after construction. Recognize that including the overlay in the design of U beams
can significantly limit their ability to span longer span lengths.
 Distribute 2/3 of the rail dead load to the exterior beam and 1/3 of the rail dead load to the adja-
cent interior beam applied to the composite cross section.
 Each U beam has two interior diaphragms at a maximum average thickness of 13 in. They are
located as close as 10 ft. from midspan of the beam. Account for each diaphragm as a 2-kip
load for U40 beams and as a 3-kip load for U54 beams applied to the non-composite cross
section.
 Use section properties given on the standard drawings.
 Composite section properties may be calculated assuming the beam and slab to have the same
modulus of elasticity (for beams with fc' < 8.5 ksi). Do not include haunch concrete placed on
top of the beam when determining section properties. Section properties based on final beam
and slab modulus of elasticity may also be used, however, this design assumption must be
noted on the plans.
 Live load distribution factors for interior beams must conform to AASHTO LRFD Bridge
Design Specifications, Article 4.6.2.2.2 for flexural moment and Article 4.6.2.2.3 for shear.

U40 and U54)
 Live load distribution factors for exterior beams must conform to AASHTO LRFD Bridge
Design Specifications, Article 4.6.2.2.2 for flexural moment and Article 4.6.2.2.3 for shear,
with the following exceptions:
 When using the lever rule, multiply the result of the lever rule by 0.9 to account for
continuity.
 When the clear roadway width is greater than or equal to 20.0 ft, use a distribution factor
for two or more design lanes loaded only. Do not design for one lane loaded.
 When the clear roadway width is less than 20.0 ft, design for one lane loaded with a multi-
ple presence factor of 1.0.
The live load used to design the exterior beam must never be less than the live load used to
design an interior beam of comparable length.
 For bridges with less than three girders in the cross section, assume the live load distribution
factors for flexural moment and shear are equal to the number of lanes divided by the number
of girders. Determine the number of lanes as required by AASHTO LRFD Bridge Design
Specifications, Article 3.6.1.1.1.
m × NL
Nb
Where,
Design Criteria

 Stresses at the ends of the beam are controlled with the use of debonding. Draped strands are
not permitted in U beams.
 Debonded strands must conform to AASHTO LRFD Bridge Design Specifications, Article
5.11.43 except as noted below:
 Debond no more than 75 percent of the total number of strands.
 Debond no more than 75 percent of the number of strands in that row.
 The maximum debonding length must be the lesser of one-half the span length minus the
maximum development length, 0.2 times the beam length, or 15 feet.

U40 and U54)
 Not more than 75 percent of the debonded strands, or 10 strands, whichever is greater,
shall have the debonding terminated at any section, where section is defined as an incre-
ment (e.g. 3 feet, 6 feet, 9 feet).
 Grouping of U-beam designs are at the discretion of the designer. However, no exterior U
beam may have less carrying capacity than that of an interior U beam of equal length. If the
designer chooses to group beams, a general rule is to group beams with no more than a four-
strand difference.
 See Prestressed Concrete I Beams and I Girders for other design criteria.
Detailing
Detail span sheets for a cast-in-place slab with precast concrete panels.

Chapter 3 — Superstructure Design Section 8 — Prestressed Concrete Slab Beams
Section 8 — Prestressed Concrete Slab Beams
Materials
'
Use Class H concrete with a minimum fci' of 4.0 ksi and fc of 5.0 ksi.
Design beams for 0.5-in. low-relaxation strands.
The maximum skew angle for slab beam bridges is 30 degrees.
The minimum gap between adjacent slab beams is 0.5-in. A preferable gap range is 1 in. to 1.5 in.
A 5-in. minimum thickness composite concrete slab is required.
Structural Analysis

cross section.
 Use section properties given on the prestressed concrete slab beam standard drawings.
 Composite section properties may be calculated assuming the beam and slab overlay have the
same modulus of elasticity (for beams with fc' < 8.5 ksi). Do not include haunch concrete
placed on top of the beam when determining section properties. Section properties based on
final beam and slab modulus of elasticity may also be used, however, this design assumption
must be noted on the plans.
 Live load distribution factors for all beams, both moment and shear, must conform to AASHTO
LRFD Bridge Design Specifications. Table 4.6.2.2.2b-1, using cross section(g), if the beams
are connected only enough to prevent relative vertical displacement at their interfaces. This is
called S/D distribution.
 Do not apply the skew correction factors for moment as suggested in Article 4.6.2.2.2e nor for
shear as suggested in Article 4.6.2.2.3c.
or shear, as less than m × N L
Nb

Chapter 3 — Superstructure Design Section 8 — Prestressed Concrete Slab Beams
Where,
Design Criteria

 Add strands in the order shown on the PSBNS standard drawing, available at http://
www.dot.state.tx.us/insdtdot/orgchart/cmd/ cserve/standard/bridge-e.htm.
 Debond strands in 3-ft. increments at beam ends if necessary to control stresses at release.
Bridge Design Specifications, Article 5.8. Change stirrup spacing as shown on relevant stan-
dard drawings available at http://www.dot.state.tx.us/insdtdot/ orgchart/cmd/cserve/standard/
bridge-e.htm only if analysis indicates inadequacy of the standard design.
 TxDOT standard slab beams satisfy Article 5.8.4 and Article 5.10.10 of the AASHTO LRFD
Bridge Design Specifications.
to have the same modulus of elasticity. Assume Ec = 5,000 ksi for beams with fc' < 8.5 ksi.
Show predicted slab deflections on the plans even though field experience indicates actual
deflections are generally less than predicted. Use the deflection due to slab weight only times
0.8 for calculating haunch depth.
 See Section 5, Prestressed Concrete I Beams and I Girders for other design criteria.

Chapter 3 — Superstructure Design Section 9 — Prestressed Concrete Decked Slab
Beams
Section 9 — Prestressed Concrete Decked Slab Beams
Materials
'
Use Class H concrete with a minimum fci of 4.0 ksi and fc of 5.0 ksi.
'
Use non-shrink cementitious grout for shear keys.
Use prestressing strand with a specified tensile strength, f pu , of 270 ksi.
The maximum skew angle for decked slab beam bridges is 30 degrees.
A 2-in. minimum thickness asphaltic concrete pavement (ACP) overlay is required.
Structural Analysis
Beams designs must meet the following requirements:

 Distribute the weight of one railing to no more than three beams.
 Use section properties provided on the prestressed concrete decked slab beam standard
drawings.
 Live load distribution factors for all beams - both moment and shear - must conform to AAS-
HTO LRFD Bridge Design Specifications, Table 4.6.2.2b-1, using cross section (j) if beams are
connected only enough to prevent relative vertical displacement at their interfaces. Use K = 2.0
when determining the live load distribution factor.
 Use S/10 as maximum limit on live load distribution.
 Do not apply the skew correction factor for moment as suggested in Article 4.6.2.2.2e.
Nb
Where,

Chapter 3 — Superstructure Design Section 9 — Prestressed Concrete Decked Slab
Beams
Design Criteria

 Strands should be added and debonded in the order shown on the DSBND standard drawings,
available at http://www.dot.state.tx.us/insdtdot/orgchart/cmd/cserve/standard/bridge-e.htm.
 Debond no more than 75% of the strands per row or per sections. The maximum debonding
length must be the lesser of one-half the span length minus the maximum development length
specified in Article 5.11.4.2 of the AASHTO LRFD Bridge Design Specifications, 0.2 times the
beam length, or 15 ft.
Bridge Design Specifications, Article 5.8. Change stirrup spacing as shown on the DSB stan-
dard drawings, available at http://www.dot.state.tx.us/insdtdot/orgchart/cmd/cserve/standard/
bridge-e.htm, only if analysis indicates the inadequacy of the standard design.
 Standard decked slab beams satisfy Article 5.8.4 and Article 5.10.10 of the AASHTO LRFD
 Connect adjacent beams with lateral connectors, shown on standard drawings DBS, spaced at 5
ft. maximum, with the first lateral connectors set 1 ft. from bent centerlines. See span standard
drawings for completion of lateral connection details.
 See Section 5, Prestressed Concrete I Beams, for other design criteria.

Chapter 3 — Superstructure Design Section 10 — Prestressed Concrete Double-Tee
Beams
Section 10 — Prestressed Concrete Double-Tee Beams
Materials
'
Use Class H concrete with a minimum fci of 4.0 ksi and fc of 5.0 ksi.
'
Use non-shrink cementitious grout for shear keys.
Double-tee standard drawings do not accommodate skewed bridges.
A 5-in. minimum thickness composite concrete slab or 2-in. minimum thickness asphaltic concrete
pavement (ACP) overlay is required.
Six-ft. wide beams are required for fascia positions when beams are not topped with a 5-in. slab.
Structural Analysis

 Use section properties provided on the prestressed concrete double-tee beam standard
drawings.
 Composite section properties may be calculated assuming the beam and composite concrete
slab overlay have the same modulus of elasticity (for beams with fc' < 8.5 ksi). When deter-
mining section properties, do not include haunch concrete placed on top of the beam. Section
properties based on final beam and slab modulus of elasticity may also be used, however, this
design assumption must be noted on the plans.
 Regardless of topping, live load distribution factors for all beams, both interior as well as exte-
rior, and both moment and shear, must conform to AASHTO LRFD Bridge Design
Specifications, Table 4.6.2.2.2b-1, using cross section (i) if beams are connected only enough
to prevent relative vertical displacement at their interfaces. Use K = 2.2 when determining the
live load distribution factor. Use S/10 as maximum limit on live load distribution.
 Do not apply the skew correction factors for moment as suggested in Article 4.6.2.2.2e nor for
shear as suggested in Article 4.6.2.2.3c.

Chapter 3 — Superstructure Design Section 10 — Prestressed Concrete Double-Tee
Beams
m × NL
Nb
Where,
Design Criteria

 Strands should be added and depressed in the order shown on the DTBND standard drawings,
available at http://www.dot.state.tx.us/insdtdot/orgchart/cmd/cserve/s tandard/bridge-e.htm.
 Use hold-down points shown on the DTBS and DTBO standard drawings, available at http://
www.dot.state.tx.us/insdtdot/orgchart/cmd/cserve/standard/bridge-e.htm.
 The end position of depressed strands should be as low as possible so that the position of the
strands does not control the release strength. Release strength is occasionally controlled by end
conditions when the depressed strands have been raised to their highest possible position.
Bridge Design Specifications, Article 5.8. Change stirrup spacing as shown on the DTBS and
DTBO standard drawings, available at http://www.dot.state.tx.us /insdtdot/orgchart/cmd/
cserve/standard/bridge-e.htm, only if analysis indicates the inadequacy of the standard design.
 TxDOT standard double-tee beams satisfy Article 5.8.4 of the AASHTO LRFD Bridge Design
Specifications.
 For double-tee beams with a composite concrete slab overlay, compute deflections due to slab
weight and composite dead loads assuming the beam and slab to have the same modulus of
elasticity. Assume Ec = 5,000 ksi for beams with fc' < 8.5 ksi. Show predicted slab deflections
on the plans even though field experience indicates that actual deflections are generally less
than predicted. Use the deflection due to slab weight only times 0.8 for calculating haunch
depth.
 TxDOT standard double-tee beams satisfy Article 5.10.10 of the AASHTO LRFD Bridge
Design Specifications.
 Connect adjacent beams with lateral connectors, shown on standard drawings DTBS and
DTBO, spaced at 5 ft. maximum, with the first lateral connectors set 5 ft. from bent center-
lines. See span standard drawings for completion of lateral connection details.
 See Section 5, Prestressed Concrete I Beams and I Girders, for other design criteria.

Chapter 3 — Superstructure Design Section 11 — Prestressed Concrete Box Beams (Types
B20, B28, B34, and B40)
Section 11 — Prestressed Concrete Box Beams (Types B20, B28, B34, and B40)
Materials
'
Use Class H concrete with a minimum of fci = 4.0 ksi and fc' = 5.0 ksi.
Use Class S concrete ( fc' = 4.0 ksi) for shear keys.
Design beams for 0.5-in low-relaxation strands.
The maximum skew angle for box beam bridges is 30 degrees.
The maximum gap between adjacent box beams is 2 in. The minimum gap between adjacent box
beams in 1 in.
A 5-in. minimum thickness composite concrete slab overlay or 2-in. minimum thickness asphaltic
concrete pavement (ACP) overlay is required.
Structural Analysis

 Use section properties given on the prestressed concrete box beam standard drawings.
 Composite section properties may be calculated assuming the beam and composite concrete
slab overlay have the same modulus of elasticity (for beams with fc' < 8.5 ksi). When deter-
mining section properties, do not include haunch concrete placed on top of the beam. Section
properties based on final beam and slab modulus of elasticity may also be used, however, this
design assumption must be noted on the plans.
Article 4.6.2.2.2 and Article 4.6.2.2.3. Use:
 Cross section (f) with bridges having a composite concrete slab
 Cross section (g) with bridges having ACP applied directly to tops of beams, assuming
beams are sufficiently connected to act as a unit.
 Do not apply the skew correction factor for moment as suggested in Article 4.6.2.2.2e.

B20, B28, B34, and B40)
m× NL
Nb
Where,
Design Criteria

 Strands should be added and debonded in the order shown on the BBND standard drawings,
available at http://www.dot.state.tx.us/insdtdot/ orgchart/cmd/cserve/standard/bridge-e.htm.
dard drawings, available at http://www.dot.state.tx.us/insdtdot/ orgchart/cmd/cserve/standard/
 TxDOT standard box beams satisfy Article 5.8.4 and Article 5.10.10 of the AASHTO LRFD
 For box beams with a composite concrete slab overlay, compute deflections due to slab weight
and composite dead loads assuming the beam and slab to have the same modulus of elasticity.
Assume Ec = 5,000 ksi for beams with fc' < 8.5 ksi. Show predicted slab deflections on the
plans even though field experience indicates actual deflections are generally less than pre-
dicted. use the deflection due to slab weight only times 0.8 for calculating haunch depth.

B20, B28, B34, and B40)
 Use shear keys for all box beam bridges. Do not consider composite action between beams and
shear keys in computing live load distribution factors, nor for strength, stress or deflection
calculations.
 Transverse post-tensioning is required for box beam bridges topped with an ACP overlay
applied directly to the tops of beams. Space tendons at 10 ft. maximum with the first tendons
set 10 ft. from bent centerlines. Post-tensioning details are provided on standard drawing
BBCDO.

Chapter 3 — Superstructure Design Section 12 — Prestressed Concrete Spread
Box Beams (X-Beams)
Section 12 — Prestressed Concrete Spread Box Beams (X-Beams)
Materials
'
Use Class H concrete with a minimum of fci = 4.0 ksi and fc' = 5.0 ksi.
Design beams for 0.5-in low-relaxation strands.
Use prestressing strand with a specified tensile strength, fpu , of 270 ksi.
The maximum skew angle for X-beam bridges is 30 degrees.
Structural Analysis

cross section.
 Use section properties given on the prestressed concrete X-beam standard drawings.
 Composite section properties may be calculated assuming the beam and composite slab have
the same modulus of elasticity (for beams with fc' < 8.5 ksi). When determining section prop-
erties, do not include haunch concrete placed on top of the beam. Section properties based on
final beam and slab modulus of elasticity may also be used, however, this design assumption
must be noted on the plans.
 Live load distribution factors for interior beams must conform to AASHTO LRFD Bridge
Design Specifications, Article 4.6.2.2.2 for flexural moment and Article 4.6.2.2.3 for shear.
 Live load distribution factors for exterior beams must conform to AASHTO LRFD Bridge
Design Specifications, Article 4.6.2.2.2 for flexural moment and Article 4.6.2.2.3 for shear,
with the following exceptions:
 When using the lever rule, multiply the result of the lever rule by 0.9 to account for
continuity.
 When the clear roadway width is greater than or equal to 20.0 ft, use a distribution factor
for two or more design lanes loaded only. Do not design for one lane loaded.
 When the clear roadway width is less than 20.0 ft, design for one lane loaded with a multi-
ple presence factor of 1.0.

Box Beams (X-Beams)
The live load used to design the exterior beam must never be less than the live load used to design
an interior beam.
m× NL
Nb
Where,
 When precast concrete deck panels or stay-in-place metal forms are allowed, design the beam
using the basic slab thickness.
Design Criteria

 Strands should be added and debonded in the order shown on the XBND standard drawings,
available at http://www.dot.state.tx.us/insdtdot/orgchart/cmd/cserve/standard/bridge-e.htm.
5.11.4.3 except as noted below:
dard drawings, available at http://www.dot.state.tx.us/insdtdot/orgchart/cmd/cserve/standard/
 TxDOT standard X-beams satisfy Article 5.8.4 and Article 5.10.10 of the AASHTO LRFD
to have the same modulus of elasticity. Assume Ec = 5,000 ksi for beams with fc' < 8.5 ksi.

Box Beams (X-Beams)
Show predicted slab deflections on the plans even though field experience indicates actual
deflections are generally less than predicted. Use the deflection due to slab weight only times
0.8 for calculating haunch depth.

Chapter 3 — Superstructure Design Section 13 — Cast-in-Place Concrete Slab and Girder
Spans (Pan Forms)
Section 13 — Cast-in-Place Concrete Slab and Girder Spans (Pan Forms)
Materials
Use Class S concrete ( fc' = 4.0 ksi). If the slab will be subjected regularly to deicing agents based
steel.
The only skew angles and span lengths available for pan form spans are provided on relevant stan-
dard drawings. Forming systems currently in use do not provide for alternative skews or span
length.
The only span lengths available for pan form spans are provided on relevant standard drawings.
Limit slab overhangs to a maximum of 13.75 inches measured from face of stem to edge of slab.
Structural Analysis
None required.
Design Criteria
None required. Pan form spans are predesigned and shown on standard drawings.

Chapter 3 — Superstructure Design Section 14 — Cast-in-Place Concrete Slab Spans
Section 14 — Cast-in-Place Concrete Slab Spans
Materials
'
Use Class S concrete ( fc = 4.0 ksi). If the slab will be subjected regularly to deicing agents, use
Class S (HPC) concrete.
Use Grade 60 reinforcing steel. Use uncoated reinforcing steel unless the slab will be subjected reg-
ularly to de-icing agents based on district policy, in which case use epoxy-coated reinforcing steel.
Waterproof slabs with one of the two classes of treatment specified in Item 428, “Concrete Surface
Treatment.”
The maximum skew angle for slab span bridges is 30 degrees. Use shear keys 2 in. deep by 6 in.
wide, parallel to traffic, with skewed spans. Shear keys should be formed into the top of substruc-
ture caps in the middle of the caps. See standard drawings for shear key details.
Break slab corners 1.5 ft. with skews more than 15 degrees.
Minimum slab depths from AASHTO LRFD Bridge Design Specifications, Table 2.5.2.6.3-1 are
guidelines but are not required.
Use a top clear cover of 2 in. Use 2.5-in. top clear cover where regular use of deicing agents is
anticipated. Use 1.25-in. bottom clear cover.
Limit span lengths to approximately 25 ft. for simple spans and end spans of continuous units.
Limit interior spans of continuous units to approximately 30 ft.
Structural Analysis
Distribute the weight of all railing and sidewalks over the entire slab width if the slab is no wider
than 32 ft. Otherwise, distribute railing load over 16 ft.
Design using 1-ft. wide strips. Take bearing centerline at cap quarter points. For interior supports of
continuous spans, assume bearing centerline coincides with cap centerline.
Apply both the axle loads and lane loads of the HL-93 live load in accordance with AASHTO LRFD
Bridge Design Specifications, Article 3.6.1.3.3 for spans more than 15 ft.

Chapter 3 — Superstructure Design Section 14 — Cast-in-Place Concrete Slab Spans
Distribute live load in accordance with AASHTO LRFD Bridge Design Specifications, Article
4.6.2.3 using Equation 4.6.2.3-2. Use Equation 4.6.2.3-3 to reduce force effects with skewed
bridges.
For longitudinal edge beams, required by AASHTO LRFD Bridge Design Specifications, Articles
5.14.4.1 and 9.7.1.4, apply one line of wheels plus the tributary portion of the lane load to the
reduced strip width specified in Article 4.6.2.1.4b.
Design Criteria
Shear design is not required when spans are designed in accordance with AASHTO LRFD Bridge
Design Specifications, Article 4.6.2.3.
The longitudinal edge beam cannot have less flexural reinforcement than interior slab regions. Do
not consider concrete barrier rails, parapets, or sidewalks in longitudinal edge beam design.
Provide bottom transverse distribution reinforcement. Use AASHTO LRFD Bridge Design Specifi-
cations, Equation 5.14.4.1-1 to determine the required amount.
Provide #4 reinforcing bars at 12-in. maximum spacing for shrinkage and temperature reinforce-
ment required to satisfy AASHTO LRFD Bridge Design Specifications, Article 5.10.8.
Assume Class 1 exposure condition when checking distribution of reinforcement for crack control
except for top flexural reinforcement in continuous spans, in which case assume Class 2 exposure
condition.

Chapter 3 — Superstructure Design Section 15 — Straight Plate Girders
Section 15 — Straight Plate Girders
Materials
Use A 709 Grade 50W steel for unpainted bridges. Use A 709 Grade 50 steel for painted bridges.
You can use A 709 Grade HPS 70W steel for both unpainted and painted bridges if it is economical
or otherwise beneficial to do so.
Use 0.875-in. or 1-in. diameter bolts for bolted connections.
Minimum flange width is 0.25D, where D=web depth, but not less than 15 in.
Minimum flange thickness is 0.75 in.
Minimum web thickness is 0.50 in.
Minimum stiffener thickness used to connect cross frames or diaphragms to girder is 0.50 in.
Structural Analysis

 Distribute the weight of one railing to no more than three girders, applied to the composite
cross section.
 Assume no slab haunch when determining composite section properties.
Article 4.6.2.2.2 for flexural moment and Article 4.6.2.2.3 for shear, except as follows:
 For exterior girder design with a slab cantilever equal to or less than half the adjacent
girder interior spacing, use the live load distribution factor for the interior girder. The slab
cantilever is the distance from the centerline of the exterior girder to the edge of the slab.
 For exterior girder design with a slab cantilever length greater than half the adjacent inte-
rior girder spacing, use the lever rule with the multiple presence factor of 1.0 for single
lane to determine the live load distribution. The live load used to design the exterior girder
must never be less than the live load used to design an interior girder.
Nb
Where,


 When checking the Fatigue and Fracture Limit State, remove the 1.2 multiple presence factor
from the one-design-lane-loaded empirical live load distribution factors.
 Use only one lane of live load in the structure model when checking the Fatigue and Fracture
Limit State.
Design Criteria

 Regarding AASHTO LRFD Bridge Design Specifications, Article 6.7.2, do not specify girders
to be out-of-plumb in the steel-dead-load-only or theoretical-no-load condition. Diaphragms
and cross frames have traditionally been installed with girders plumb and no significant prob-
lems have been reported to date. If the designer believes that analysis indicates that girders will
be significantly beyond plumb after slab concrete is placed, contact the Director of the Bridge
Division for guidance.
 Diaphragm and cross-frame designs must meet the following requirements:
 The maximum spacing is 30 ft. if all limit states requirements are met.
 Provide diaphragms/cross frames at all end bearings. At least two interior bearings at a
bent must have a diaphragm/cross frame intersecting them.
 Set diaphragms/cross frames parallel to skew up to 20 degrees. Set radial to girders
beyond 20 degrees.
 Check the limiting slenderness ratio of cross-frame members using bracing compression
member criteria provided in AASHTO LRFD Bridge Design Specifications, Article 6.9.3.
Girder designs must meet the following requirements:

 Use composite design and place shear connectors the full girder length.
 Do not use longitudinal stiffeners unless web depth exceeds 120 in.
 Use short-term modular ratio equal to 8 and long-term modular ratio equal to 24.
 Provide longitudinal slab reinforcement in accordance with AASHTO LRFD Bridge Design
Specifications, Article 6.10.1.7.
 Assume the composite slab is effective in negative bending regions for Deflection check,
Fatigue and Fracture Limit State, and Service Limit State.
 Do not use longitudinal slab reinforcement as part of the negative bending section for Strength
Limit State.

 Unbraced flange length must satisfy either, Equation 6.10.1.6-2 or Equation 6.10.1.6-3.
 At flange splices, extend thicker flanges beyond the theoretical flange splice location by a
length equal to the flange width but not more than 2 ft.
For stud connector designs, minimum longitudinal stud connector spacing is limited to 4d, where d
is the stud connector diameter.
Bolted field splices must meet the following requirements:

 Use of A 325 bolts is preferred over A 490 bolts.
 Assume Class A surface conditions. Class B surface conditions may be used only when slip
controls the number of required bolts. Always note the surface condition assumed for design in
the plans.
 Add at least 0.125 in., and preferably 0.25 in., to minimum edge distances shown in AASHTO
LRFD Bridge Design Specifications, Table 6.13.2.6.6-1.
 Do not extend and develop fill plates equal to or thicker than 0.25 in. Instead, reduce bolt shear
strength with AASHTO LRFD Bridge Design Specifications, Equation 6.13.6.1.5-1.

Chapter 3 — Superstructure Design Section 16 — Curved Plate Girders
Section 16 — Curved Plate Girders
Materials
Use A 709 Grade 50W steel for unpainted bridges. Use A 709 Grade 50 steel for painted bridges.
You can use A 709 Grade HPS 70W steel for both unpainted and painted bridges if it is economical
or otherwise beneficial to do so.
Use 0.875-in. or 1-in. diameter bolts for bolted connections.
Minimum flange width is 0.25D, where D=web depth, but not less than 15 in.
Minimum flange thickness is 1 in.
Minimum web thickness is 0.50 in.
Minimum stiffener thickness used to connect cross frames or diaphragms to girder is 0.50 in.
Structural Analysis

 Distribute the weight of one railing to no more than three girders, applied to the composite
cross section.
 Assume no slab haunch when determining composite section properties.
 A grid analysis or other refined analysis is required for curved girders. Curved girders satisfy-
ing AASHTO LRFD Bridge Design Specifications, Article 4.6.1.2.4b are excluded from this
requirement. Use a single-lane-loaded multiple presence factor of 1.0.
 Use only one lane of live load in the structure model when checking the Fatigue and Fracture
Limit State.
Design Criteria

 Regarding AASHTO LRFD Bridge Design Specifications, Article 6.7.2, do not specify girders
to be out-of-plumb in the steel-dead-load-only or theoretical-no-load condition. Diaphragms
and cross frames have traditionally been installed with girders plumb and no significant prob-
lems have been reported to date. If the designer believes that analysis indicates that girders will

be significantly beyond plumb after slab concrete is placed, contact the Director of the Bridge
Division for guidance.
 Diaphragm and cross-frame designs must meet the following requirements:
 The maximum spacing is 20 ft. with curved girders if all limit states requirements are met.
 Provide diaphragms/cross frames at all end bearings.
 Place interior diaphragms/cross frames radial to girders. Do not use staggered placement
of diaphragms/cross frames.
 Check the limiting slenderness ratio of cross-frame members using main compression member
criteria provided in AASHTO LRFD Bridge Design Specifications, Article 6.9.3.
 Diaphragm and cross-frame members are primary members. Verify their adequacy for the
Strength Limit State and other applicable limit states.
Girder designs must meet the following requirements:

 Use composite design and place shear connectors the full girder length.
 Do not use longitudinal stiffeners unless web depth exceeds 120 in.
 Use short-term modular ratio equal to 8 and long-term modular ratio equal to 24.
 Provide longitudinal slab reinforcement in accordance with AASHTO LRFD Bridge Design
Specifications, Article 6.10.1.7.
 Assume the composite slab is effective in negative bending regions for Deflection check,
Fatigue and Fracture Limit State, and Service Limit State.
 Do not use longitudinal slab reinforcement as part of the negative bending section for Strength
Limit State.
 Unbraced flange length must satisfy either AASHTO LRFD Bridge Design Specifications,
Equation 6.10.1.6-2 or Equation 6.10.1.6-3.
 At flange splices, extend thicker flanges beyond the theoretical flange splice location by a
length equal to the flange width but not more than 2 ft.
For stud connector designs, minimum longitudinal stud connector spacing is limited to 4d, where d
is the stud connector diameter.
Bolted field splices must meet the following requirements:

 Use of A 325 bolts is preferred over A 490 bolts.
 Assume Class A surface conditions. Class B surface conditions may be used only when slip
controls the number of required bolts. Always note the surface condition assumed for design in
the plans.
 Add at least 0.125 in., and preferably 0.25 in., to minimum edge distances shown in AASHTO
LRFD Bridge Design Specifications, Table 6.13.2.6.6-1.

 Do not extend and develop fill plates equal to or thicker than 0.25 in. Instead, reduce bolt shear
strength with AASHTO LRFD Bridge Design Specifications, Equation 6.13.6.1.5-1.

Chapter 4 — Substructure Design
Contents:
Section 2 — Foundations
Section 3 — Abutment
Section 4 — Rectangular Reinforced Concrete Bent Caps
Section 5 — Inverted Tee Reinforced Concrete Bent Caps
Section 6 — Columns for Multi-Column Bents

Chapter 4 — Substructure Design Section 1 — Overview
Introduction
This chapter provides guidance on Load and Resistance Factor Design (LRFD) of specific bridge
substructure components.

Chapter 4 — Substructure Design Section 2 — Foundations
Section 2 — Foundations
Guidance
Design foundations in accordance with requirements outlined in the TxDOT Geotechnical Manual,
available at ftp://ftp.dot.state.tx.us/pub/txdot-info/gsd/manuals/geo.pdf

Chapter 4 — Substructure Design Section 3 — Abutment
Section 3 — Abutment
Materials
'
Use Class C concrete ( fc = 3.6 ksi), and design for Grade 40 reinforcing steel, but allow use of
Grade 40 or Grade 60 in the plans. Higher strengths may be required in special cases.
For abutments supporting Tx62 or Tx70 girders, use a cap width of at least 4.00 ft. For all other
TxGirder types, use a cap width of 3.50 ft.
For abutment supporting Type IV beams, Type VI beams, or U beams, use a cap width of at least
3.25 ft. For all other I-beam types, use a cap width of 2.75 ft.
For all other structure types refer to the bridge standard drawings for recommended cap widths.
Design Criteria
Use the following design practice for standard type “stub” abutments with backwalls:
 Position the backwall, wing wall lengths, wing wall support, and various other standardized
items as shown in the Bridge Detailing Manual, available at http://crossroads/org/gsd/books/
det/index.htm, or applicable bridge standard drawings, available at
http://www.dot.state.tx.us/ insdtdot/orgchart /cmd/cserve/standard/bridge-e.htm.
 Cap, backwall, and wing wall reinforcing should conform to the Bridge Detailing Manual.
Structural analysis is not required for abutments within the geometric constraints noted in the
Bridge Detailing Manual.
 If no approach slab is used, calculate the horizontal forces using 40 pcf equivalent fluid
pressure with a surcharge of Δ p = kγ s heq , where k = 0.25, γ s = 120 pcf. For abutments with d
< 5 ft. take heq = 4.0 ft. For all other abutments see AASHTO LRFD Table 3.11.6.4-1. Retain-
ing type abutments in questionable soils may justify a more rigorous analysis.
 Provisions of AASHTO LRFD Bridge Design Specifications, Article 5.7.3.4 need not be satis-
fied. Limit spacing of primary flexural reinforcing bars to no more than 18 in.
For pile foundations, use battered pairs of piling for all abutments that are not otherwise restrained
from horizontal movement. Examples of sufficient restraint are slab spans and pan form spans that
are doweled into the abutment, and abutments within a mechanically stabilized fill. Never use bat-
tered piling adjacent to MSE walls because of the difficulty of installing the backfill.

Chapter 4 — Substructure Design Section 3 — Abutment
The maximum spacing of drilled shafts or pile groups should not exceed 16 ft. with beams 40 in.
and less deep nor 12.5 ft. with deeper beams.
Maximum spacing of drilled shafts or pile groups should be within the following limits:
 TxGirders less than or equal to 40 in. in depth - 13.50 ft.
 TxGirders greater than 40 in. in depth - 11.00 ft.
 All other beam types less than or equal to 40 in. in depth - 16.00 ft.
 All other beam types greater than 40 in. in depth - 12.50 ft.
Drilled shaft loads may be calculated as the total vertical load on the cap divided equally among the
cap shafts. Wing wall shaft or pile load is usually taken as 10 tons per shaft or pile.
Calculate pile loads as the total vertical load on the cap divided equally among the cap pilings. For
abutments with battered piling, add to the vertical load the load caused by 40-lb. per cu. ft. fluid
pressure from the bottom of the cap to 2 ft. above the roadway surface. The back pile should not be
allowed to go into tension due to the lateral load, considering dead load and soil pressure only.

Chapter 4 — Substructure Design Section 4 — Rectangular Reinforced Concrete Bent
Caps
Section 4 — Rectangular Reinforced Concrete Bent Caps
Materials
'
Use TxDOT Class C concrete ( fc = 3.6 ksi) and Grade 60 reinforcing steel. Higher concrete
strengths may be required in special cases.
Cap depth should be in 3-in. increments and not less than cap width.
For bents supporting Tx62 or Tx70 girders, use a cap width of at least 4.00 ft. For all other
TxGirder types, use a cap width of 3.50 ft.
For caps supporting Type IV beams, Type VI beam, or U beams, do not use a cap smaller than 3.25
ft. by 3.25 ft. For all other I-beam types, do not use a cap smaller than 2.75 ft. by 2.75 ft.
For all other structure types refer to the bridge standard drawings for recommended cap widths.
Structural Analysis
In lieu of a more detailed analysis, analyze trestle pile and multiple-column caps as simply sup-
ported beams on knife-edge supports at the center of piling or columns. If the column is wide,
consider a model that takes the stiffness of the column into consideration.
Distribute the live load to the beams assuming the slab hinged at each beam except the outside
beam.
Base live load reactions per lane on the combined effect of the truck loading added to the lane
loading.
Design Criteria
For cap design, check Strength I limit state and Service I limit state. Check distribution of rein-
forcement as required in Article 5.7.3.4 of the AASHTO LRFD Bridge Design Specifications using
Class 1 exposure for moderate exposure conditions and Class 2 exposure in areas where deicing
chemicals are frequently used. Limit tensile stress in steel reinforcement, fss under Service I limit
state to 0.6 fy.
Check Service I with dead load only, and limit reinforcement stress to 22 ksi to further minimize
cracking.

Caps
For multi-column bent caps, take design negative moments at the center line of the column. For
multi-column bent caps with wide columns, take design negative moments at the effec-
tive face of the column.
Do not use the simplified procedures for determining shear resistance allowed by AASHTO LRFD
5.8.3.4.1 nor 5.8.3.4.3. Use the General Procedure as provided by AASHTO LRFD 5.8.3.4.2.
Minimize the number of stirrup spacing changes.
Except for hammerhead bents, shear need not be considered in cantilever regions unless the dis-
tance from center of load to effective face of column exceeds 1.2d. Provide stirrups at 6-in. spacing.
For typical multi-column bent caps supporting beams on elastomeric bearing pads, strut-and-tie
modeling provisions of Articles 5.6.3 need not be considered. For bent caps supporting girders on
pot bearings or girders with large reaction forces that are defined as deep components according to
Article 5.2, use the strut-and-tie design. Diagonal cracks have been observed in caps with large
beam reactions and small pads designed using the traditional sectional model. Strut-and-tie analysis
indicates that the diagonal compressive struts were overloaded in these instances.
When calculating the cracking moment of a member in accordance with Article 5.7.3.3.2, take the-
For single-column bents, straddle bents, and other non-typical

bents, provide minimum stirrups and longitudinal side face rein-
forcing in the region between each face of column and first girder
such that the following are satisfied:
Av/bwsv > 0.003 and,
Ah/bwsh > 0.003
Also, for longitudinal side face reinforcement in these regions,

satisfy the requirements of Article 5.7.3.4 for Ask. The longitu-
dinal side face demands of the two independent procedures need not
be additive; use the larger value produced by Articles 5.6.3.6 and
5.7.3.4.
Please see the following illustration for further clarification of

the terms Av and Ah:

Caps
Figure 4-1. Clarification of the terms Av and Ah.
Detailing
Use #5 stirrups with a 4-in. minimum and a 12-in. maximum spacing. Do not use stirrups larger
than #6. Use double stirrups if required spacing is less than 4 in.
For flexural reinforcement, use #11 bars. Smaller bars can be used to satisfy development require-
ments. Do not mix bar sizes.
Use longitudinal skin reinforcement in accordance with Equation 5.7.3.4-2 of the AASHTO LRFD
Bridge Design Specifications in caps deeper than 3 ft. Caps 3 ft. and less should have two #5 bars
equally spaced in each side face.

Chapter 4 — Substructure Design Section 5 — Inverted Tee Reinforced Concrete Bent
Caps
Section 5 — Inverted Tee Reinforced Concrete Bent Caps
Materials
'
Use TxDOT Class C concrete ( fc = 3.6 ksi) and Grade 60 reinforcing steel. Higher concrete
strengths may be required in special cases.
Make inverted tee dimensions the same for all bents on the project.
Keep the top of stem at least 2.5 in. below the bottom of the slab; see standard drawing IBMS or
IGMS, available at http://www.dot.state.tx.us/insdtdot/orgchart/cmd/cserve/standard/bridge-e.htm.
Structural Analysis
Analyze multiple-column caps as simply supported beams on knife-edge supports at the center of
piling or columns. If the column is wide, consider a model that takes the stiffness of the column
into consideration.
Distribute the live load to the beams assuming the slab hinged at each beam except the outside
beam.
Design Criteria
For cap design, check Strength I limit state and Service I limit state. Check distribution of rein-
forcement as required in Article 5.7.3.4 of the AASHTO LRFD Bridge Design Specifications using
Class 1 exposure for moderate exposure conditions and Class 2 exposure for areas where deicing
chemicals are frequently used. Limit tensile stress in steel reinforcement, fss under Service I limit
state to 0.6 fy.
Check Service I with dead load only, and limit reinforcement stress to 22 ksi to further minimize
cracking.
For multi-column bent caps, take design negative moments at the center line of the column. For
wide columns, take design negative moments at the effective face of the column.
Minimize the number of stirrup spacing changes.
When designing for beam ledge punching shear, replace AASHTO LRFD Article 5.13.2.5.4 with
the following:

Caps
 Use df, not de, in all ledge punching shear calculations.

 The truncated pyramids assumed as failure surfaces for punching shear, as illustrated in Figure
1, shall not overlap. Therefore, 0.5bw + a v must be greater than 0.5L + d f to prevent longitu-
dinal overlap. S must be greater than 2d f + W to prevent transverse overlap.
 Normal punching shear resistance, Vn , kip, shall be taken as:
At interior pads: Vn = 0. 125 f c (W + 2L + 2d f )d f
'

 At exterior pads Vn = 0. 125 f c' (0. 5W + L + d f + C )d f , except shall not be taken

greater than 0.125 f ' (W + 2 L + 2d )d .
c f f
 Replace AASHTO LRFD Equation 5.13.2.5.5-1 with the following:
2 
Ahr  f y 
Vn =  3  (W + 3a )
v
s
 Replace the following sentence in AASHTO LRFD Article 5.13.2.5.5: “The edge distance
between the exterior bearing pad and the end of the inverted T-beam shall not be less than de"
with the following: "The edge distance between the exterior bearing pad and the end of the
inverted T-beam shall not be less than 12 inches.”
 Replace the following sentence in AASHTO LRFD Article 5.13.2.5.5: "The hanger reinforce-
ment specified herein shall be provided in addition to the lesser shear reinforcement required
on either side of the beam reaction being supported" with the following: "Do not superimpose
loads on stirrups acting has hangers and loads on stirrups acting as shear reinforcement. Pro-
portion the web reinforcement in the stem of an invert T-beam based on required hanger
reinforcement or required shear reinforcement, whichever is greater."
Provide minimum stirrups and longitudinal side face reinforcing in

the region between each face of column and first girder such that
the following are satisfied:
Av/bwsv > 0.003 and,
Ah/bwsh > 0.003
Also, for longitudinal side face reinforcement in these regions,

satisfy the requirements of Article 5.7.3.4 for Ask. The longitu-
dinal side face demands of the two independent procedures need not
be additive; use the larger value produced by Articles 5.6.3.6 and
5.7.3.4.

Caps
Please see the following illustration for further clarification of

the terms Av and Ah:
Figure 4-2. Clarification of the terms Av and Ah
Detailing
Provide extra vertical reinforcing across the end surfaces of the stem to resist cracking. Do not weld
bars together for development of ledge reinforcing. Use anchorage hooks to develop ledge
reinforcing.
Use stirrups with a 12-in. maximum spacing.
Use longitudinal skin reinforcement in accordance with Equation 5.7.3.4-2 of the AASHTO LRFD
Bridge Design Specifications in caps deeper than 3 ft. Caps 3 ft. and less should have two #5 bars
equally spaced in each side face.

Chapter 4 — Substructure Design Section 6 — Columns for Multi-Column Bents
Section 6 — Columns for Multi-Column Bents
Materials
'
Use TxDOT Class C concrete ( fc = 3.6 ksi) and design for Grade 40 reinforcing steel, but allow
use of Grade 40 or Grade 60 in the plans. Higher concrete or steel strengths may be required in spe-
cial cases.
Structural Analysis
Design is not necessary for round columns with the column diameter, typical reinforcement and
recommended height limits shown in the following figure, as long as the column spacing is
between 10 feet and 18 feet:
Figure 4-3. Round columns.

Chapter 4 — Substructure Design Section 6 — Columns for Multi-Column Bents
 Slab spans -- 24 in.

 Pan form spans -- 24 in.
 Types Tx28 through Tx54 -- 36 in.
 Types Tx62 and Tx70 -- 42 in.
 Types A and B and C prestressed beam spans -- 30 in.
 Types IV and VI prestressed beam spans and U-beam spans -- 36 in.
 For other beam types, compare drilled shaft load to what would be expected using one of the
preceding superstructures, and use a column diameter as appropriate.

Chapter 5 — Other Designs
Contents:
Section 1 — Widenings
Section 2 — Steel-Reinforced Elastomeric Bearings for Prestressed Concrete Beams
Section 3 — Strut-and-Tie Method
Section 4 — Corrosion Protection

Chapter 5 — Other Designs Section 1 — Widenings
Section 1 — Widenings
Design Recommendations
Design guidelines for various elements of new bridges may also be applied to bridge widenings.
Complete a load rating and condition survey before plans are started. Ratings should be based on
the 17th edition of the American Association of State Highway and Transportation Officials (AAS-
HTO) Standard Specifications for Highway Bridges, except that allowable stresses should be based
on the minimum material strengths used on the original construction.
Refer to the Bridge Project Development Manual for additional requirements for load ratings and
condition surveys.
Design widened portions for HL93 loading using the AASHTO LRFD Bridge Design
Specifications.
Show load rating and design loads on the bridge plan, for example, HS20(Existing) and
HL93(Widening).

Chapter 5 — Other Designs Section 2 — Steel-Reinforced Elastomeric Bearings
for Prestressed Concrete Beams
Section 2 — Steel-Reinforced Elastomeric Bearings for Prestressed Concrete Beams
Materials
Use 50-durometer neoprene for steel-reinforced elastomeric bearings.
Use a shear modulus range of 95 to 175 psi for design, using the least favorable value for the design
check.
Make steel shims 0.105 in. thick.
Do not use adhesives between bearings and other components.
See standard drawings available at http://www.dot.state.tx.us/insdtdot/orgchart/cmd/cserve/stan-

dard/bridge-e.htm for standard pad details.
Tapered bearings may be used if the taper does not exceed 0.055 ft./ft. For beams on steeper grades,
use a beveled steel sole plate field-welded (1/4-in. fillet) to a 1/2-in. steel plate embedded in and
anchored to beams with headed stud anchors. Use a minimum of four 1/2-in.-by-3-in. stud anchors
with studs located between strands and reinforcement. The minimum thickness of sole plate should
be 1.5 in. of steel between weld and elastomer. The sole plate should extend at least 1 in. beyond
the beam flange. Sole plates should not be vulcanized to the bearing to allow slip to occur at the
beam/bearing interface.
Use 1/4-in. exterior pad layers. If using 1/4-in. interior pad layers, disregard the requirements in the
AASHTO LRFD Bridge Design Specifications, Article 14.7.6.1, specifying exterior layers no
thicker than 70% of internal layers.
Structural Analysis
Assume a temperature change of 70 degrees Fahrenheit after erection when calculating thermal
movement in one direction (not total). Take Tmin = 10 degrees F and Tmax = 80 degrees F. For the
panhandle region use Tmin = 10 degrees F and Tmax = 115 degrees F, for a total temperature change
of 105 degrees F.
Do not include shrinkage, creep, and elastic shortening when determining maximum movement,
which will be accommodated through infrequent slip.
Use appropriate shear live load distribution, modified for skew.

Use the critical DL condition (the lightest predicted DL) when checking against slip.
Use Load Combination Service I for all gravity loads.
Ignore limit on Si 2 n in AASHTO LRFD 14.7.6.1.
Design Criteria
Follow Design Method A in AASHTO LRFD Bridge Design Specifications, Article 14.7.6, with the
following exceptions:
 DL compressive stress limit is the lesser of 1.20 ksi and 1.2 GS.
 Total compressive stress limit is the lesser of 1.50 ksi and 1.5 GS. This limit can be exceeded
up to 15% at the engineer’s discretion.
 For rotation check, disregard AASHTO LRFD Bridge Design Specifications, Article 14.7.6.3.5.
θ (0.8L )
Rotation is acceptable if the total compressive deflection equals or exceeds 2 , where L
is the pad length defined in AASHTO LRFD Bridge Design Specifications, and θ is the total
rotation. Estimate compressive deflection using AASHTO LRFD Bridge Design Specifications,
Figure C14.7.6.3.3-1.
 Calculate total rotation for dead and live load plus 0.005 radians for construction uncertainties
as required by AASHTO LRFD Bridge Design Specifications, Article 14.4.2.1. Take maximum
4Δ
live load rotation as SpanLength , where is midspan LL deflection.
 Check bearing pad slip as follows:
(0.2 − Gr ) × DL × hrt
Δ s ( allow ) ≤
(G × A)
where:
Gr = beam grade in ft./ft.
DL = lightest unfactored predicted dead load (kips)
hn = total elastomer thickness (in.)
G = shear modulus of elastomer at 0 degrees F, typical 0.175 ksi
A = plan arc of elastomer (sq. in.)
Δ s ( allow ) = maximum total allowable shear deformation (in.)
 You may use hn, instead of total pad height when checking stability as required in AASHTO
LRFD Bridge Design Specifications, Article 14.7.6.3.6.

Detailing
Use standard drawing IBEB for guidance on detailing custom bearing pad designs.

Chapter 5 — Other Designs Section 3 — Strut-and-Tie Method
Section 3 — Strut-and-Tie Method
The angle between compression struts and tension ties must be greater than 26 degrees.
Structural Analysis
Strut and Tie Modeling shall not be used for standard girders and bent caps, but instead it can be
used for footings, dapped beam ends, post-tensioning anchorage zones, deviation diaphragms,
bents that use high performance bearings, and other special designs.
Place nodes at applied loads and reactions. More nodes can be added as long as the tension ties are
located where reinforcement is normally placed. The nodes should be located at the center of the
tension ties and compression struts. If there is sufficient concrete in the incoming member the strut
can be considered within both members, such as in the case with a column and a footing, and the
nodes can be placed where the two members meet.
A 3 dimensional truss can be broken into multiple 2 dimensional trusses to be analyzed. When ana-
lyzing the 2 dimensional trusses, use the same reactions as the 3 dimensional truss, but recalculate
the applied loads so equilibrium is satisfied.
Design Criteria
When designing broad members that are uniformly loaded on one end and discretely loaded on the
other end, use AASHTO LRFD Bridge Design Specifications, Article 5.10.9.4.
Development length for the tension tie reinforcement must be in accordance with AASHTO LRFD
Bridge Design Specifications, Articles 5.6.3.4.2 and 5.11.2.
Nodal geometry is needed to analyze the capacity of a strut and the capacity of the node itself; how-
ever, if the node is significantly large, such as with a column and a footing, no nodal analysis is
needed. If nodal analysis is needed, use AASHTO LRFD Bridge Design Specifications, Article
5.6.3.5.
Replace AASHTO LRFD 5.6.3.3.3 with the following:

 For struts with reinforcement satisfying Section 5.6.3.6:
0. 85 tan θ ln
ν= 1
f c
' ws sin θ but not greater than the minimum of

and 0.85
ln
0.85
ws sin θ
 For struts without reinforcement satisfying Section 5.6.3.6:
0. 85 tan θ ln
ν=
3 f c
' ws sin θ but not greater than the minimum of1
ln
0.85
ws sin θ and 0.85
The nominal capacity of a strut shall be taken as2: Pn = ν f c Ac
'
where:
Pn = nominal capacity of a strut (kip)
ν = efficiency factor
fc' = specified compressive strength (ksi)
Ac = cross-sectional area of the strut at the face of the node (in2)
θ = angle between the compressive strut and the adjoining tie (deg)
l n = length of the node adjoining the strut. For CCC and CCT nodes l n = l b and for CTT
nodes l n = l b from Figure 5.6.3.3.2-1.
ws = width of the strut at the face of the node (Figure 5.6.3.3.2-1)
Replace AASHTO LRFD Bridge Design Specifications Figure 5.6.3.3.2-1b "(b) Strut anchored by
bearing and reinforcement" with the following figure:
1. Brown, Michael et al. "Design for Shear in Reinforced Concrete Using Strut-and-Tie Models," Report No. FHWA/TX-
06-0-4371-2, Appendix A, Equation A-7.

Figure 5-1.
Replace AASHTO LRFD Bridge Design Specifications, Figure 5.6.3.3.2-1 "(a) x-x" (cross section)
with the following figure:
Figure 5-2.
Replace AASHTO LRFD 5.6.3.6 with the following:

 Structures and components or regions thereof, except for slabs and footings, which have been
designed in accordance with the provisions of Article 5.6.3, and using the efficiency factor
associated with reinforced struts (Equation A-7) shall contain crack control reinforcement in
an orthogonal grid. Horizontal reinforcement alone shall be used. The spacing of the bars in
the strut reinforcement shall not exceed 12.0 in.
 The amount of reinforcement within a strut shall be calculated as1:
2 2
 A   AsV 
ρ ⊥ =  sH  +  
 b ⋅ sH   b ⋅ sV 
Where:
ρ ⊥ = equivalent reinforcement perpendicular to the strut axis
AsH = total of horizontal reinforcement in a strut within spacing sH(in2)
b = width of the member (in)
sH = spacing of horizontal reinforcement (in)
AsV = total area of vertical reinforcement in a strut within a spacing, sV(in2)
sV = spacing of vertical reinforcement (in)
 The minimum amount of reinforcement in a strut shall be taken as2:
Pu
ρ ⊥ ,min = ≥ 0.003
2 f y blm (A15)
Where:
Pu = factored load in a strut (kip)

fy = yield strength of the reinforcement within a strut (ksi)
b = width of the member transverse to the plane of the strut-and-tie model
l = length of the strut
m = slope of the angle of compression dispersion (Figure 5-3)

Figure 5-3.
Guidelines
The tension tie reinforcement must be close enough to the drilled shaft to be considered in the truss
analysis. Therefore, the tension tie reinforcement must be within a 45 degree distribution angle
(i.e. no more than dc away from the member on either side).
Use strut bearing lengths proportional to the amount of load carried by the strut at a node.
Conservatively assume the width of a strut in a CCC node, hs, as the height of the compression
block.

Chapter 5 — Other Designs Section 4 — Corrosion Protection
Section 4 — Corrosion Protection
Guidance
In areas of the state where deicing agents are frequently used during winter storms, it is recom-
mended that additional corrosion protection measures be incorporated into the bridge design and
details. Consult the Bridge Information web page for statewide and district specific
recommendations.

Aashto Bridge Design (LRFD) Manual

Uploaded by

Copyright:

Available Formats

Aashto Bridge Design (LRFD) Manual

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Aashto Bridge Design (LRFD) Manual

Uploaded by

Copyright:

Available Formats

Bridge Design Manual - LRFD

Revised December 2011

Manual: Bridge Design Manual - LRFD

Effective Date: December 22, 2011

Past manual notices are available in a PDF archive.

Chapter 2 — Limit States and Loads

Chapter 3 — Superstructure Design

Bridge Design Manual - LRFD i TxDOT 12/2011

Bridge Design Manual - LRFD ii TxDOT 12/2011

Chapter 4 — Substructure Design

Bridge Design Manual - LRFD iii TxDOT 12/2011

Chapter 5 — Other Designs

Bridge Design Manual - LRFD iv TxDOT 12/2011

Bridge Design Manual - LRFD 1-1 TxDOT 12/2011

Updates to this manual are summarized in the following table.

Version Publication Date Summary of Changes

2005-1 July 2005 New manual

2006-1 June 2006 Revision adding information on cast-in-place concrete spans,

2006-2 July 2006 Revision adding information in Chapter 3 on prestressed concrete U

Bridge Design Manual - LRFD 1-2 TxDOT 12/2011

Manual Revision History

Version Publication Date Summary of Changes

2011-1 December 2011 Revisions to manual to update information in

Bridge Design Manual - LRFD 1-3 TxDOT 12/2011

 Chapter 4, Substructure Design. Policy on LRFD design of specific bridge substructure

Bridge Design Manual - LRFD 1-4 TxDOT 12/2011

Bridge Design Manual - LRFD 2-1 TxDOT 12/2011

Section 1 — Limit States

Bridge Design Manual - LRFD 2-2 TxDOT 12/2011

Vehicular Collision Force

Bridge Design Manual - LRFD 2-3 TxDOT 12/2011

Special considerations include the following:

Except as noted below, bridges and structures in Texas do not

The TxDOT Bridge Standards and conventional bridge configurations

For conventional structures with superstructure unit lengths or

Non-conventional or exotic bridges do not require seismic evalua-

Bridge Design Manual - LRFD 2-4 TxDOT 12/2011

Bridge Design Manual - LRFD 2-5 TxDOT 12/2011

Bridge Design Manual - LRFD 3-1 TxDOT 12/2011

Bridge Design Manual - LRFD 3-2 TxDOT 12/2011

Section 2 — Concrete Deck Slabs on Stringers

For TxGirders limit overhang widths as follows:

Bridge Design Manual - LRFD 3-3 TxDOT 12/2011

 For Tx 28 and Tx34, 4.0 ft.

Bridge Design Manual - LRFD 3-4 TxDOT 12/2011

Section 3 — Concrete Deck Slabs on U Beams (U40 and U54)

Bridge Design Manual - LRFD 3-5 TxDOT 12/2011

Bridge Design Manual - LRFD 3-6 TxDOT 12/2011

Section 4 — Concrete Deck Slabs on Slab Box Beams (X-Beams)

Bridge Design Manual - LRFD 3-7 TxDOT 12/2011

Bridge Design Manual - LRFD 3-8 TxDOT 12/2011

TxDOT standard composite concrete slabs are 5 in. thick, minimum.

For longitudinal reinforcement, use #4 bars spaced at 12 in. maximum.

Bridge Design Manual - LRFD 3-9 TxDOT 12/2011

Section 6 — Prestressed Concrete I Beams and I Girders

Beam designs must meet the following requirements:

Bridge Design Manual - LRFD 3-10 TxDOT 12/2011

Standard beam designs must meet the following requirements: