Nstrument Control & Electrician Test

STUDY GUIDE INSTRUMENT
CONTROL & ELECTRICIAN

TECHNICIAN TEST
TEST #2178
Instrument Control & Electrician Technician Test #2178.r1017

INTRODUCTION
The 2178 Instrument Control and Electrician (ICE) Technician Test is a job knowledge test
designed to cover the major knowledge areas necessary to perform the job. This Guide contains
strategies to use for taking tests and a study outline, which includes knowledge categories, major job
activities, and study references.
TEST SESSION
It is important that you follow the directions of the Test Administrator exactly. If you have any
questions about the testing session, be sure to ask the Test Administrator before the testing begins.
During testing, you may NOT leave the room, talk, smoke, eat, or drink. Since some tests take
several hours, you should consider these factors before the test begins.
All questions on this test are multiple-choice format and have four possible answers. All knowledge
tests will be taken on the computer. Consult the following link and click on Computer Based Testing
for more information: All questions on this test are multiple-choice format and have four possible
answers. All knowledge tests will be taken on the computer. Consult the following link and click on
Computer Based Testing.
The test has a three hour time limit. A non-programmable scientific calculator will be provided
for you to use during the test. The calculator provided during the test session will be:
Texas Instruments TI-36X
You will NOT be able to bring or use your own calculator during testing.
You will receive a Test Comment form so that you can make comments about test questions. Write
any comments you have and turn it in with your test when you are done.
INFORMATION GUIDE FEEDBACK

At the end of this Guide you have been provided with an Information Guide Feedback page. If a
procedure or policy has changed, making any part of this Guide incorrect, your feedback would be
appreciated so that corrections can be made.

TEST TAKING STRATEGIES
INTRODUCTION
The 2178 Instrument Control and Electrician (ICE) Test contains multiple-choice questions and
may also contain hot spot questions. The purpose of this section is to help you to identify some
special features of a multiple-choice test and to suggest techniques for you to use when taking one.
Your emotional and physical state during the test may determine whether you are prepared to do your
best. The following list provides common sense techniques you can use before the test begins.
CONFIDENCE
If you feel confident about passing the test, you may lose some of your anxiety. Think of the test as a way of
demonstrating how much you know, the skills you can apply, the problems you can solve, and your good
judgment capabilities.
PUNCTUALITY
Arrive early enough to feel relaxed and comfortable before the test begins.
CONCENTRATION
Try to block out all distractions and concentrate only on the test. You will not only finish faster but you
will reduce your chances of making careless mistakes. If possible, select a seat away from others
who might be distracting. If lighting in the room is poor, sit under a light fixture. If the test room
becomes noisy or there are other distractions or irregularities, mention them to the Test Administrator
immediately.
BUDGET YOUR TIMES

Pace yourself carefully to ensure that you will have enough time to complete all items and review your
answers.
READ CRITICALLY
Read all directions and questions carefully. Even though the first or second answer choice looks
good, be sure to read all the choices before selecting your answer.
MAKE EDUCATED GUESSES

Make an educated guess if you do not know the answer or if you are unsure of it.

CHANGING ANSWERS
If you need to change an answer when testing on a computer, be sure that the new answer is
selected instead of the old one.
RETURN TO DIFFICULT QUESTIONS

If particular questions seem difficult to understand, make a note of them, continue with the test and
return to them later.
DOUBLE CHECK MATH CALCULATIONS

Use scratch paper to double check your mathematical calculations.
REVIEW
If time permits, review your answers. Do the questions you skipped previously. When testing on a computer,
make sure each multiple choice question has a dot next to the correct answer.
Remember the techniques described in this section are only suggestions. You should follow the test taking
methods that work best for you.

INSTRUMENT THEORY AND PRACTICE (9 ITEMS)
Includes knowledge of the types and methods of measurement and control of flow, pressure, level, and
temperature. Knowledge of strategies of control dynamics, such as PID (Proportional, Integral and Derivative)
loops. Knowledge of how to test, troubleshoot, repair, and maintain instrumentation equipment.
SAFETY (10 ITEMS)

Includes knowledge of electrical safety procedures and precautions as specified by Cal OSHA and the National
Electric Code (NEC). Knowledge of how to install electrical, instrumentation, and control equipment following
regulatory processes and safety standards and procedures. Knowledge of how to test, troubleshoot, repair,
and maintain control equipment following safety processes and procedures. Knowledge of work authorization,
including lock out tag out (LOTO). Knowledge of the use of high voltage safety equipment, hazardous material
safety equipment, and personal protection equipment (PPE).
ELECTRONICS (7 OF ITEMS)
Includes knowledge of basic electronic theory, circuitry, electronic symbols, solid state theory, diodes,
transistors, and AC/DC voltage regulators. 2
TEST EQUIPMENT (15 OF ITEMS)

Includes knowledge of the proper use of various test instruments, such as multimeters, meggers, ductors,
oscilloscopes, handheld communicators, high voltage meters, ammeters, and manometers. Knowledge of the
purpose of the tests applied, why it is appropriate, and the accuracy requirements. Knowledge of test
tolerances. Knowledge of test and calibration requirements and how to interpret test and calibration results.
PHYSICS AND CHEMISTRY (4 ITEMS)

Knowledge of applied physics, including fluids, gasses, dynamic forces of levers, pneumatics, and hydraulics.
Knowledge of basic chemistry as it applies to chemical measurement and control used in water treatment.
Knowledge of chemical and physical properties of instrumentation applications.
INSTRUMENT/ELECTRICAL MAINTENANCE AND INSTALLATION (17 OF ITEMS)

Includes knowledge of installation, maintenance, and repair of batteries. Knowledge of how to perform (install,
repair, maintain) low voltage wiring. Knowledge of how to perform conduit installation based upon the National
Electric Code (NEC). Knowledge of how to perform connection practices and how to install and repair
communication wiring. Knowledge of the types and applications of hand tools used in the instrumentation field
and of power tools (e.g., drill motors, conduit benders, etc.). Knowledge of standard installation practices of
flow instrumentation, pressure instrumentation, level instrumentation, temperature sensors and transducers,
final control elements (e.g., valves, dampers), and tubing installations. Knowledge of logical applications of
troubleshooting instrument problems using electrical drawings and Piping & Instrument Diagrams (P&ID).
Knowledge of logical applications of troubleshooting instrument problems using electrical drawings. Knowledge
of variable frequency drive (VFDs). Knowledge of soft start motor controls.

MATH (4 ITEMS)
Includes knowledge of algebra, geometry, and trigonometry. Ability to apply mathematical formulas to job
related problems.
CONTROLS/PROGRAMMING (4 ITEMS)
Includes knowledge of programmable logic controllers (PLC) and associated equipment, such as HMI screen,
router, power supply, UPS, etc.

STUDY REFERENCES
ELECTRICAL THEORY AND PRACTICE

Electricity One-Seven, 3rd Edition, by Harry Mileaf.
Delmar Standard Textbook of Electricity, 4th Edition.
INSTRUMENT THEORY AND PRACTICE

Programmable Logic Controllers, by W. Bolton.
Instrumentation 4th ed, by F, Kirk, T Weedon, P Kirk (2005).
Measurement and Control Basics, 3 rd Edition, by T.A. Hughes.
SAFETY
2011 National Electric Code.
Federal OSHA Standards, 29CFR, Sections 1910.137, 1910.331 to 1910.335, &1926.957.
www.OSHA.gov.us.
ELECTRONICS
Electronics Principles, 8th Edition, by Albert P Malvino.
TEST EQUIPMENT
Measurement and Control Basics, 3 rd Edition, by T.A. Hughes.
PHYSICS AND CHEMISTRY


INSTRUMENT/ELECTRICAL MAINTENANCE AND INSTALLATION
Electronics Principles, 8th Edition, by Albert P Malvino.
Soft Starter Bypass Technology in Smart Motor Controllers, by Bernhardt, William & Anderson,
Richard, Rockwell Automation.
http://www.csanyigroup.com/download/knowledge/ansi-ieee-device-numbers
MATH
Math The Easy Way, 3rd Edition, by Prindle & Prindle.
Trigonometry The Easy Way, 3rd Edition, by Douglas Downing.
CONTROLS/PROGRAMMING
Programmable Logic Controllers, by W. Bolton.

STUDY GUIDE FEEDBACK
Please use this page to notify us of any changes in policies, procedures, or materials affecting this
guide. Once completed, return to:
Southern California Edison
Human Resources - Talent & Assessment Programs
G.O. 5, 1st Floor
1515 Walnut Grove Ave.
Rosemead, CA 91770
TEST NAME: 2178 Instrument Control and Electrician (ICE) Technician Test
COMMENTS SECTION:

Nstrument Control & Electrician Test

Uploaded by

Copyright:

Available Formats

Nstrument Control & Electrician Test

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Nstrument Control & Electrician Test

Uploaded by

Copyright:

Available Formats

STUDY GUIDE INSTRUMENT

CONTROL & ELECTRICIAN

Instrument Control & Electrician Technician Test #2178.r1017

INFORMATION GUIDE FEEDBACK

Instrument Control & Electrician Technician Test #2178.r1017

BUDGET YOUR TIMES

MAKE EDUCATED GUESSES

Instrument Control & Electrician Technician Test #2178.r1017

RETURN TO DIFFICULT QUESTIONS

DOUBLE CHECK MATH CALCULATIONS

Instrument Control & Electrician Technician Test #2178.r1017

SAFETY (10 ITEMS)

TEST EQUIPMENT (15 OF ITEMS)

PHYSICS AND CHEMISTRY (4 ITEMS)

INSTRUMENT/ELECTRICAL MAINTENANCE AND INSTALLATION (17 OF ITEMS)

Instrument Control & Electrician Technician Test #2178.r1017

Instrument Control & Electrician Technician Test #2178.r1017

ELECTRICAL THEORY AND PRACTICE

INSTRUMENT THEORY AND PRACTICE

PHYSICS AND CHEMISTRY

Instrument Control & Electrician Technician Test #2178.r1017

Instrument Control & Electrician Technician Test #2178.r1017

Instrument Control & Electrician Technician Test #2178.r1017

You might also like