892ELC Excavator Introduction

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

892E LC EXCAVATOR

Introduction And Customer Information


TP43846 A.1

John Deere 892E-LC Excavator


(Manufactured 1993-1998)
(Specifications And Design Subject To Change Without Notice.)

To the Customer
The part numbers in this parts catalog were correct at the time your catalog was published. It is our policy to constantly improve our machines,
and therefore, part numbers may change. When ordering parts, verify part numbers through your dealer.

SI Units of Measure
Metric dimensions are given, where applicable, throughout this parts catalog.

Bolt and Cap Screw Strength Identification


Bolts and cap screws required to have high-strength qualities equivalent to SAE grade 8 are identified throughout this catalog by the description
HS SAE 8 (10.9 for metric). All standard bolts and cap screws are SAE grade 5 (metric 8.8) or lower.

Serial Number Listing Information


Serial number information is listed to show on which machines each part can be used; for example:
– The part can be used on all products.
000000 – The part can be used on products beginning with the serial number listed.
– 000000 The part can be used on products up to and including the serial number listed.
000000 – 000000 The part can be used on products between and including the serial number listed.
When XXXXXX's are listed in place of a serial number, a serial number change was made, but the exact serial number was not available when
the catalog was produced.
If product identification numbers or serial numbers are required for warranty claims or correspondence pertaining to this product, it is extremely
important that all characters be furnished. This point cannot be overemphasized.

Direction Arrow
Arrows are used with illustrations to indicate the front of the unit. “Right-Hand” and “Left-Hand” sides are determined by facing in direction of ma-
chine forward travel.

Box-enclosed Illustrations
A key number, shown in the parts list, is assigned to a box enclosing all parts sold as a service assembly. A box not keyed includes non-current
parts.

PC2376 (C.1) JUN-20 1/6


892E LC EXCAVATOR

Complete Goods Listings


Complete Goods are listed in bold face type. Order separately. Do not include on replacement part order.

Orientation of Engine
“Right Hand” and “Left Hand” sides are determined by standing at the flywheel and facing the engine.

John Deere Reman Components


The service parts listed in this catalog are intended for the repair of original equipment components. Although most service parts may be used
to repair remanufactured components, the remanufacturing process may change parts sufficiently so that service parts are inadequate or not us-
able.

Serial Number Locations


Each 892E-LC Excavator Has Seven Serial Number Plates: A Product Identification Number Plate, An Engine Serial Number Plate, A Hydraulic
Pump Serial Number Plate, A Left-Hand Propel Motor Serial Number Plate, A Right-Hand Propel Motor Serial Number Plate, A Swing Motor Ser-
ial Number Plate And A Control Valve Serial Number Plate.
The Product Identification Plate Is Located On The Right-Hand Side Frame Near The Front Support.
The Engine Serial Number Plate Is Located On The Right Side Of The Cylinder Block Near The Fuel Pump.
The Hydraulic Pump Serial Number Plate Is Located Near The Front Of The Hydraulic Pump.
The Swing Motor Serial Number Plate Is Located On The Top Of The Swing Motor.
The Propel Motor Serial Number Plate Is Located On The Rear Of The Propel Motor.
The Control Valve Serial Number Plate Is Located On The Upper Left-Hand Side Of The Control Valve.
Left Side, Right Side, Front And Rear Of The Excavator Are Viewed By Facing In The Direction Of The Excavator Forward Travel.
If Product Identification Numbers Or Serial Numbers Are Required For Warranty Claims Or Correspondence Pertaining To This Product.
It Is Extremely Important That All Characters Be Furnished. This Point Cannot Be Overemphasized.

Product Identification Number


A.1

First Line Designates


CK - Hitachi Excavator Manufacturer
892E-LC Excavator Model
LC Excavator Configuration
000000 Excavator Serial Number
Second Line Designates
Excavator Unit Type

PC2376 (C.1) JUN-20 2/6


892E LC EXCAVATOR

Short Block Serial Number Identification


RGP4460 A.1

Serial number stamped into casting of block near previous serial number plate.
1. RE60386 Service Part Number
2. 02 Month Assembled
3. 95 Year Assembled

PC2376 (C.1) JUN-20 3/6


892E LC EXCAVATOR

Engine Serial Number Plate — 6081 & 6090


RGP13838 A.1

Engine Serial Number is Defined by 13 Characters


First Line Designates
1 — Two letters for engine factory designation RG: Waterloo, USA, JX: Rosario, Argentina
2 — One digit for number of cylinders. 6 Cylinder
3 — Three digits for displacement in liters 081: 8.1 Liter, 090:9.0 Liter
4 — One letter for aspiration type A= Turbocharged with air-to-water after-cooler
D= Naturally Aspirated
H= Turbocharged with air-to-air after cooler
T= Turbocharged
S= Turbocharged with air-to-sea water after-cooler
5 — Six digits 123456= Engine build sequence number. Sequence numbers
start at 000001
Engine Type is Defined by 9 Alpha-Numerical Characters
6 — Four digits Same as items 2 and 3 above
7 — One letter for aspiration type Same as items 4 above
8 — One or two letters for OEM application F: OEM, FM: Marine, FH: HazLoc, FN: Compressed Natural
Gas
8 — One or two letters for John Deere Vehicle application TJ: Forestry, RW: Tractor, H, Z, CQ: Combine, N: Pick-
er/Sprayer, DW: Construction, T8: Sugar Cane Harvester
9 — Two or three digits for version 485

PC2376 (C.1) JUN-20 4/6


892E LC EXCAVATOR

Trademarks
Throughout this parts catalog, you may find the following Deere and Company trademarks:
Best Bid™ CounterParts™ DEERE™ (Deere™)
Dura-Trax™ Fanggs™ Guardian™
HTH™ Jagz™ JDLink™
MARKS™ MIC™ [Machine Information Center] MTH™
Power Curve™ Powerllel™ PowerShift Plus™
Powerwize™ POWR SAVR™ PowrShift™
ProPath™ Quad-Cool™ Quik-Tatch™
SC-2™ Side-Tracker™ Stinger™
StructureALL™ Swamper™ TMC™ [Total Machine Control]
ValueSelect™ Waratah™ Worksite Pro™
FlexBox™ Funk™ iTorque™
Phoenix™ Phoenix International™ PowerTech™
PowerTech™ E PowerTech™ M PowerTech™ Plus
Precision Joint™ SHIFT-O-MATIC™ SWEDA™ (Super Wide Extreme Dual Axle)
TeamMate™ TeamMate™II TeamMate™ IV
TMII™ TMIII™

PC2376 (C.1) JUN-20 5/6


892E LC EXCAVATOR

Remarks and Abbreviations


The following remarks and abbreviations may appear throughout this parts catalog. Refer to the following table for translations.
Phrase Meaning Phrase Meaning
ALSO ORDER, ORD W/ Also Order MFWD Mechanical Front Wheel Drive
AMP Ampere NA, NOT USED THIS APPL Not used in this application
APPL, APPL ONLY This application only NLA No longer available
AR As required NSEP Not available separately
ASSY Complete assembly OD Outside diameter
BOAC Bolt-on cutting edge OPTIONAL Optional
CCW Counterclockwise OR Or
COMPLETE Complete ORD, ORDER Order
COMPLETE GOODS Complete goods OS Oversize
CONVENIENCE ASSY, CA Convenience assembly OUTER Outer
CTL, CUT TO LENGTH Cut to length PKG, PACKG Package, Packet of
CW Clockwise PTO Power Take Off
ENGINE Engine RATIO Ratio
FOR For REAR Rear
FRONT Front REMAN Remanufactured
GAS Gasoline REPL Replaces
HFWD Hydraulic Front-Wheel Drive RH Right-hand
HP Horsepower SN Serial number
HS, HEAD MARKED High Strength, head marked STD Standard
ID Inside diameter SUB Replaced by
INCH Inch SUB COMPONENTS Substitute components (of the
kit or assy)
INCL KEYS Includes keys… SUB FOR Substitutes for
INCL, INCLUDES Includes… TEETH, Z Number of gear teeth
INCLUDES PARTS/ ITEMS Includes parts/items marked… TK Thickness
MARKED
INNER Inner UP, UPPER Upper
KIT Kit US Undersize
L Number of links USE UNTIL EXHAUSTED Use until exhausted
LF, LINE FILL Line Fill USE WITH Use with
LGP Low Ground Pressure VEC Vehicle Electronic Controller
LGTH Length VLC Vehicle Load Center
LT Long Track WHOLE GOODS Whole Goods
MAKE FROM, MF Make from WT Wide Tracks
MARKED Marked XLT Extra Long Track
MATCHED SET Matched set

PC2376 (C.1) JUN-20 6/6

You might also like