Humayun 2016

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

Available online at www.sciencedirect.

com

ScienceDirect
Procedia Engineering 148 (2016) 1320 – 1325

4th International Conference on Process Engineering and Advanced Materials

The Effect of Co-solvent on the Solubility of a Sparingly Soluble Crystal of


Benzoic Acid
Hudzaifah Yousuf Humayun, M Nizamuddin N. M. Shaarani, Ali warrior, Bawadi Abdullah, Md
Abdus Salam*
Universiti Teknologi PETRONAS,32610, Bandar Seri Iskandar, Perak Darul Ridzuan, Malaysia

Abstract

The Benzoic acid is widely used in the pharmaceutical industry, plasticizers and food preservative which show low aqueous solubility and
dissolution rate. The investigation has been made to improve the solubility of benzoic acid by using co-solvent. The co-solvent solution is
prepared by using glycerol in water by volume ratio. The result shows the relation between solubility in different co-solvent and temperature
whereby as the percentage of glycerol increase, the solubility of benzoic acid increase. A similartrend was depicted in term of solubility relation
with temperature as the temperature increase amount of benzoic acid dissolved also increase. Thermodynamics dissociation constant, pKa are
directly proportional totemperature between 30oC and 90oC. Enthalpy and entropy change of the dissociation process are 2.907 kJ/mole and -
24.09 J/mole respectively. Gibbs free energy of dissociation at 30oC, 60oC and 90oC are -4.390 KJ/mole, -5.114 KJ/mole and 5.837 KJ/mole
respectively depicted that the solubility increased with temperature.
© 2016 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license
© 2016 The Authors. Published by Elsevier Ltd.
(http://creativecommons.org/licenses/by-nc-nd/4.0/).
Peer-review under
Peer-review under responsibility
responsibilityof
ofthe
theorganizing
organizingcommittee
committeeofofICPEAM 2016.
ICPEAM 2016
Keywords: Solubility; Co-solvent; Benzoic Acid; Sparingly Soluble; Glycerol

1. Introduction

Crystallization is natural or manufactured phenomenon in the development of solid crystals that deposit from a solution or
precipitating directly from gas. Crystallization plays an important role in the various field of research such as pharmaceuticals,
physics, chemistry, food science, biological science and etc [1, 2, 3, 4]. Benzoic acid (C7H6O2) is a colorless crystalline solid,
which is widely used as an important intermediate for the preparation of many other organic substances applied in the fields of
pharmaceuticals, resins, plasticizers, dyes, cosmetics and preservatives [5, 6]. It is used as an intermediate in the biosynthesis of
various secondary metabolites as well in the preparation of cosmetics, resins, dyes, and pharmaceutical industries [7]. Its salts are
mainly used as food preservatives, fats, and fruit juices. Industrially, it is obtained as a by-product during the liquid phase
oxidation of toluene with air as an oxidant and acetic acid as solvent. Therefore, knowledge of the solubility of benzoic acid in
solvents as well as a reactant is important for making the reaction mixture homogeneous and also for separations. Solubility, in
quantitative, is term as the concentration of solute in a saturated solution at a certain temperature [8,9]. It is also defined as the
spontaneous interaction of two or more substance to form a homogeneous molecular dispersion. Although major of the solute
follows the solubility principal, it was found that some solute decrease solubility in increasing of temperature. The crystal
solubility may be expressed as amolality, percentage, parts, molarity, volume fraction, and mole fraction. Benzoic acid is an
aromatic carboxylic acid. It contains an aromatic ring or a benzene ring and one hydroxyl group attached to its carbon. The
benzene ring has a hydrophobic characteristic, which tends to be non-polar and not soluble in water. The reason why benzoic

* Corresponding author. Tel.: +605-368 7616; H/P: +6019-291 2198.


E-mail address: [email protected]

1877-7058 © 2016 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license
(http://creativecommons.org/licenses/by-nc-nd/4.0/).
Peer-review under responsibility of the organizing committee of ICPEAM 2016
doi:10.1016/j.proeng.2016.06.548
Hudzaifah Yousuf Humayun et al. / Procedia Engineering 148 (2016) 1320 – 1325 1321

acid is considered to be sparingly soluble in the first place is because of its ability to form hydrogen bonding with water
[10,11,12]. Water also consist a hydroxyl group and as the principle like dissolve like imply, meaning there is hydrogen bonding
between benzoic acid and water. But due to the benzene ring, it makes the benzoic acid less soluble. The enhancement of
solubility of benzoic acid (BA) is becoming more important thus the study of the solubility is relevant. A number of
methodologies can be adapted to improve solubility of benzoic acid. A few methods established in the study of increasing
solubility of sparingly soluble drugs, including the use of co-solvents, surfactants, organics and hydrophilic macromolecules,
complexation, emulsion, liposomes, particle size reduction, solid dispersion, micronization, chemical modification, pH
adjustment and others [1]. In the determination of a compound solubility, there are a few factors that affect the solubility, such as
temperature, pressure, particle size, sonication, ionic strength and impurities [13,14]. The solubility depends on the polarity of
the solute and solvent. In general, a polar solute dissolves in a polar solvent where the solubility of a polar solute is relatively low
or insoluble in a non-polar solvent. Solubility increases with the increasing temperature, but it may not be necessary in all cases.
For the endothermic process, as the temperature increase solubility also increase and vice versa while the process is exothermic
[15]. In the case of pressure, the effect on solids and liquids are generally negligible and only significant in affecting the
solubility of gaseous in liquid. As the pressure increase, the solubility of gasses in liquid also increases. The characteristic of the
solute plays important rules in dissolution. In summary, solubility is affected by numbers of factors, whereby manipulating the
factors would give either positive or negative impact on concentration dissolve. Due to the highly demand of the solubility data
of benzoic acid in the pharmaceutical, food and other industry, many research efforts have been applied in overcoming the low
solubility of benzoic acid . Many types of co-solvent can be used such as polyethylene glycol (PEG), glycerin, and ethanol [16].
Sparingly soluble salt is known to be less soluble in water, but in many cases, their solubility increase when toreact with water
and its co-solvent. Several studies have investigated the solubility of benzoic acid in (acetic acid + water) binary mixtures. There
is a scope to explore the effect of glycerol as co-solvent (glycerol + water) in enhancing the solubility of benzoic acid that has not
been investigated in details yet. Therefore, the objective of this research is to study the effect of glycerol as co-solvents on the
solubility at various temperatures.

2. Methodology

2.1 Materials

Analytical reagent grade benzoic acid (BA) with purity of 99.5% by mass was used in thewhole investigation and 99%
Glycerol by volume was used as co-solvent compositions. The solvent contains with glycerol and distilled water.

2.2 Experimental procedure

Benzoic acid solubility in different percentage of glycerol was investigated using a static analytical method and the saturated
solution composition was determined using thegravimetric method. Preparation of 500 ml of solvent was prepared by mixing a
certain amount of glycerol (in percent) and water (balance amount) together at the desired temperature. An excess amount of
benzoic acid was weighed and placed in the solvent solution. The solution was left to stir continuously for at least 3 hours.
Different dissolution time was tested and the result shows 3 hours was enough time for benzoic acid to achieve saturation in all
percentage of co-solvent. After the continuous stir, the solution was kept still for 1 hour to let the undissolved particle settle
down in the lower level of the equilibrium solution. Once the gravitational settling was completed, 3 ml of clear solution was
immediately taken out into a previously weighed vial using a pre-heated syringe. The vial was weighed again to identify the mass
of the sample. The vial is placed in a dryer for 24 hours at 303 K to evaporateall the solvent of the solution. Once the drying
process was done, the vial together with the remaining solutes was weighed again. The vial was weighed repeatedly until a
constant weight of the vile was achieved. The solubility of benzoic acid was calculated in term of molality. The solubility data
was measured at 10% increment of co-solvent with 15 K increment of temperature from 303.15 K to 363.15 K.

3. Result and Discussion

3.1 Co-solvent effect on Solubility of Benzoic acid(BA)

The effect of co-solvent on the solubility and the apparent dissociation constant (Kc) of benzoic acid at 30oC was investigated
at ten different percent of glycerol in the range of 0-90% glycerol. Figure 1 shows the molality of benzoic acid dissolve in the
water-glycerol solvent. The graph plotted between the molality versus the percentage of glycerol in water shows an upward
trend, increase in molality as the percentage of glycerol added increase. In every set of temperature that has been tested, it shows
a steady increment of 0% of glycerol to 70% of glycerol, whereby from 70% to 90%, shows a significant increment in molality.
Thus, as the percentage of glycerol added increase, the solubility of benzoic acid also increase.The solubility of Benzoic acid is
well known to be sparingly soluble in water. From another study, the effect of adding another solvent into the primary solvent
will enhance the solvent power thus increase in solubility. The benzene ring has a hydrophobic characteristic, which tends to be
1322 Hudzaifah Yousuf Humayun et al. / Procedia Engineering 148 (2016) 1320 – 1325

non-polar and not soluble in water.The reason why benzoic acid is considered to be sparingly soluble in the first place is because
of its ability to form hydrogen bonding with water. Water also consist a hydroxyl group and there is hydrogen bonding between
benzoic acid and water. Due to thebenzene ring, it makes the benzoic acid less soluble.In term of solubility, glycerol is easily
dissolved in water because, it consist three hydroxyl group attached to each carbon, making more hydrogen bonding. From the
mixing of both solvent, theamount of hydroxyl group increase, therefore, ahigher amount of benzoic acid could undergo
hydrogen bonding, thus as the amount of glycerol increase, the solubility of benzoic acid also increases.
525 303.15 K
318.15 K
450 333.15 K
348.15 K
363.15 K
375

Molality (Mol.Kg )
-1
300

225

150

75

0
0 20 40 60 80 100
Percent of glycerol in water (%)

Figure 1: Effect of co-solvent on the solubility of benzoic acid

Apparent dissociation constant (Kc) of benzoic acid was determined using the modulated expression below for each solution
[8];
(1)

Where,y is the total molar solubility of benzoic acid in solution. Table 1 contains values of y, 10-pH, Kc, and percent of glycerol
for each benzoic acid solution at 30oC, 60oC and 90oC.

Table 1: Benzoic acid dissociation constant and solubility at different temperature

At temperature 30°C
percent of Volume of Concentration of
pH Log Kc Kc
glycerol, I benzoic acid benzoic acid, y
0.1 3.977165354 0.007105741 0.316227766
6227 4.88 -2.7308 0.001859
0.3 4.237322835 7.18266028 0.547722558 5.15 -6.00628 9.86E-07
0.5 7.95480315 19.23042166 0.707106781 5.41 -6.69399 2.02E-07
0.7 8.362362205 55.47995346 0.836660027 5.68 -7.42414 3.77E-08
0.9 7.903937008 330.4944826 0.948683298 5.88 -8.39916 3.99E-09
At temperature 60°C
percent of Volume of Concentration of
pH Log Kc Kc
glycerol, I benzoic acid benzoic acid, y
0.1 6.339370079 1.825782266 0.316227766 4.91 -5.17145 6.74E-06
0.3 12.67385827 7.650396669 0.547722558 5.18 -6.06368 8.64E-07
0.5 15.86598425 23.21859029 0.707106781 5.45 -6.81584 1.53E-07
0.7 24.43503937 64.63671268 0.836660027 5.73 -7.54048 2.88E-08
0.9 26.24094488 411.4008254 0.948683298 5.93 -8.54427 2.86E-09
At temperature 90°C
percent of Volume of Concentration of
pH Log Kc Kc
glycerol, I benzoic acid benzoic acid, y
0.1 27.11622047 2.806034287 0.316227766 4.95 -5.39809 4E-06
0.3 58.07188976 8.367238062 0.547722558 5.22 -6.14258 7.2E-07
Hudzaifah Yousuf Humayun et al. / Procedia Engineering 148 (2016) 1320 – 1325 1323

0.5 89.13070866 26.87870648 0.707106781 5.47 -6.89941 1.26E-07


0.7 77.23188976 75.96290159 0.836660027 5.79 -7.6706 2.14E-08
0.9 56.98937008 486.8085476 0.948683298 6.01 -8.69736 2.01E-09

A relation between apparent and thermodynamics dissociation constant for aqueous solutions at 30˚C

(2)

Figure 2 shows the plot oflogKc versuspercent of glycerol (I). Linear least-square analysis of the data at 30oC finds the
thermodynamic dissociation constant Ka of benzoic acid. The calculated value of logKa from the plot is -3.98 ± 0.043. The
inverse of the predicted value corresponds thermodynamic dissociation constant,pKa of benzoic acid at 30oC which is agreed with
theliterature [9].

-4
logKc

-6 logKa=-3.98

-8

0.0 0.2 0.4 0.6 0.8 1.0


1/2
I

Figure 2: Thermodynamic dissociation constant of benzoic acid with co-solvents

3.2 Temperature effect on Solubility of Benzoic acid(BA)

One of the major factors that affects solubility is temperature. In general, the solution process will absorb energy and the
solubility will increase as the temperature increase, but the solubility will decrease in increment of temperature if the solution
process releases energy. Figure 3 (a, b, c) shows the exact trend of the solubility where solubility increase as the temperature
increase until 90oC.
0% Co-solvent
10% Co-solvent 50% Co-solvent
20% Co-Solvent 60% Co-solvent
16 30% Co-solvent 500 70% Co-Solvent
80% Co-solvent
40% Co-solvent
90% Co-solvent
400
12
Molality (Mol.Kg )
Molality (Mol.Kg )

-1
-1

300
8

200
4

100

304 320 336 352 368 304 320 336 352 368
Teperature (K) Teperature (K)
(a) (b)
1324 Hudzaifah Yousuf Humayun et al. / Procedia Engineering 148 (2016) 1320 – 1325

Figure 3: Effect of Temperature on the solubility of benzoic acid (a) For 0% to 40% Glycerol (b) 50% to 90%Glycerol

The dissociation of benzoic acid for different percent of glycerol at 30oC, 60oC and 90oC was evaluated by repeating the
procedure, and predicting the pH of each solution. Kcvalue for each percent glycerol solution at each temperature was calculated
using thesame method to get thermodynamic dissociation constants (pKa) using the plots of logKc versus I. Figure 4 demonstrate
the relation between the calculated pKa values and temperature used. The relation between the values of pKaand temperature
(between 30oC and 90oC) are directly proportional. Linear form of thermodynamic equation (Van't Hoff equation) can be used to
find ΔH andΔS of the benzoic acid dissociation at temperature between 30oC and 90oC:

(3)

In the equation (3), R is the universal gas constant (8.314 J∙K-1∙mol-1), and ǼH and ǼS are independent on temperature because
of infinitesimal change of temperature. A linear plot of logKa versus 1/T (Figure 5) gives thermodynamics parameters such as ΔH
andΔS of dissociation of BA (benzoic acid) for different percent of glycerol as co-solvent [10]. The dissociation enthalpy and
entropy change are 2.907 kJ/mol and -24.09 J/mol, respectively. Since the process changes the state of benzoic acid from solid
to liquid, theentropy of the process is negative.

3.40
-3.32
3.38

3.36
logKa
pKa

-3.36
3.34

3.32
-3.40
3.30
300 310 320 330 340 350 360 370 0.0028 0.0030 0.0032
o
Temperatire / K 1/T
Figure 4: A plot of Van't Hoff equation Figure 5: The effect of temperature of the value of Ka

Gibbs free energy (∆Go) was estimatedusing the following relation:



ΔGo = ΔHo −TΔSo (4)

Gibbs free energies at 30oC, 60oC and 90oC are -4.390 KJ/mol, -5.114 KJ/mol and 5.837 KJ/mol respectively. Dissociation of
benzoic acid decreases as the temperature increases that reduces the value of pKa. The dissociation of benzoic acid is exothermic
and spontaneous in the range of temperature of 30 - 90oC. The effect of temperature on benzoic acid dissociation under glycerol
co-solvent is due to the polarity effect which results inductance inside the molecules [11]. As the temperature increase, the
overall change of Gibbs free energy become more negative, thus causing spontaneity of reaction to increase. As a result,
solubility increases with temperature increase.

4. Conclusion

The solubility of benzoic acid in glycerol co-solvent increases with anincrement of the glycerol concentration which corresponds
that the co-solvent of glycerol enhanced the solubility of the benzoic acid. There is no regular trend of thermodynamics
dissociation constant of benzoic acid in the range of temperature between 30oC to 90oC. Benzoic acid (BA) dissociation in
glycerol co-solvent is spontaneous above the temperature 30oC since the Gibbs free energy are negative.

Acknowledgements

Authors would like to thanks, University Technology for providing financial support and laboratory facilities for this study.
Hudzaifah Yousuf Humayun et al. / Procedia Engineering 148 (2016) 1320 – 1325 1325

References

[1] P. Khadka, Pharmaceutical particle technologies: An approach to improve drug solubility, dissolution and bioavailability, Asian Journal of Pharmaceutical
Sciences 9 (2014) 304-316.
[2] A. K. El-Zhry El-Yafi and H. El-Zein, Technical crystallization for application in pharmaceutical material engineering: Review article, Asian Journal of
Pharmaceutical Sciences, 10 (2015) 283-291.
[3] P. Khadka, J. Ro, H. Kim, I. Kim, J. T. Kim, H. Kim, et al., Pharmaceutical particle technologies: An approach to improve drug solubility, dissolution and
bioavailability, Asian journal of pharmaceutical sciences, 9 (2014) 304-316
[4] E. Kougoulos, A. Jones, K. Jennings, and M. Wood-Kaczmar, Use of focused beam reflectance measurement (FBRM) and process video imaging (PVI) in a
modified mixed suspension mixed product removal (MSMPR) cooling crystallizer, Journal of Crystal Growth, 273(2005) 529-534
[5] J. K. Sa„ib. Titrimetric Study of the Solubility and Dissociation of Benzoic Acid in Water: Effect of Ionic Strength and Temperature. American Journal of
Analytical Chemistry, 6 (2015) 429.
[6] H.Wang, Q. Wang, Z. Xiong, C. Chen, B. Shen. Solubilities of benzoic acid in binary (benzyl alcohol+ benzaldehyde) solvent mixtures. The Journal of
Chemical Thermodynamics, 83 (2015) 61-66.
[7] A.Yurquina, M. E.Manzur, P. Brito, R. Manzo, & M. A. A. Molina. Solubility and dielectric properties of benzoic acid in a binary solvent: Water- ethylene
glycol, Journal of Molecular Liquids 108(2003) 119-133.
[8] A. Avdeef, Solubility of sparingly-soluble ionizable drugs, Advanced drug delivery reviews, 59 (2007) 568-590.
[9] J. Molpeceres, M. Guzmán, P. Bustamante, and M. del Rosario Aberturas, Exothermic-endothermic heat of solution shift of cyclosporin A related to
poloxamer 188 behavior in aqueous solutions, International journal of pharmaceutics,130 (1996) 75-81.
[10] M. El-Badry and M. Fathy, Enhancement of the dissolution and permeation rates of meloxicam by formation of its freeze-dried solid dispersions in
polyvinylpyrrolidone K-30, Drug development and industrial pharmacy 32 (2006)141-150.
[11] A. Yurquina, M. Manzur, P. Brito, R. Manzo, and M. Molina, Solubility and dielectric properties of benzoic acid in a binary solvent: Water-ethylene glycol,
Journal of molecular liquids, 108(2003)119-133.
[12] Kumari, A., Sandeepa, K., Prathap Kumar, T., & Satyavathi, B. (2015). Solubility, Thermodynamic Properties, and Derived Excess Properties of Benzoic
Acid in (Acetic Acid+ Water) and (Acetic Acid+ Toluene) Binary Mixtures. Journal of Chemical & Engineering Data. 61 (2016) 67-77
[13] J. Delgado and M. Vázquez da Silva, Experimental Values of Solubility of Organic Compounds in Water for a Wide Range of Temperature Values− A New
Experimental Technique, in Defect and Diffusion Forum, 6 (2010)1244-1249.
[14] J.-P. Fan, X.-K. Xu, G.-L. Shen, and X.-H. Zhang, Measurement and correlation of the solubility of genistin in eleven organic solvents from T=(283.2 to
323.2) K, The Journal of Chemical Thermodynamics, 89 (2015) 142-147.
[15] N Sharin, solubility and dissolution of drug product: a review, International Journal of Pharmaceutical and Life Sciences, 2 (2013) 33-41.
[16] B. Long, J. Li, R. Zhang, L. Wan, Solubility of benzoic acid in acetone, 2-propanol, acetic acid and cyclohexane: Experimental measurement and
thermodynamic modeling, Fluid Phase Equilibria, 297(2010)113-120.

You might also like