Scribd
Upload
1K views2 pages

Compulsory Ppe As Needed Ppe: Safe Operating Procedures SOP 02 - Bench Grinder

This document provides safety procedures for operating a bench grinder. It lists required personal protective equipment and safety checks that must be performed before and during operation of the grinder. Hazards associated with using the grinder are identified as hot metal, sparks, noise, and eye injuries. The document stresses the importance of training and understanding operating manuals before using the equipment. Employees must sign off to acknowledge they have read and understand the safety operating procedures.

Uploaded by

Muhammad Oji L
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views2 pages

Compulsory Ppe As Needed Ppe: Safe Operating Procedures SOP 02 - Bench Grinder

This document provides safety procedures for operating a bench grinder. It lists required personal protective equipment and safety checks that must be performed before and during operation of the grinder. Hazards associated with using the grinder are identified as hot metal, sparks, noise, and eye injuries. The document stresses the importance of training and understanding operating manuals before using the equipment. Employees must sign off to acknowledge they have read and understand the safety operating procedures.

Uploaded by

Muhammad Oji L
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Safe Operating Procedures

SOP 02 – Bench Grinder

DO NOT use this tool unless appropriately instructed in its safe use and operation and
permission to operate has been given.

COMPULSORY PPE AS NEEDED PPE

PRE-OPERATIONAL SAFETY CHECKS


1. Check workspaces and walkways to ensure no slip/ trip hazards are present.
2. Ensure all guards and safety shields (spark deflectors) are in position before starting the grinder.
3. Check that electrical cords are not damaged.
4. Ensure that the grinding wheels are properly ‘dressed’ and that wheels do not touch the tool rest and that
the gap between wheel and rest is no greater than 1.5 mm.
5. Check that grinding wheels are running true (regularly dressed) and are not glazed or loaded.
6. Locate and ensure you are familiar with the operation of the ON/OFF start switch and the Emergency Stop
button (where fitted).
7. Faulty equipment must not be used. Immediately report and repair any damaged machinery.

OPERATIONAL SAFETY CHECKS


1. Stand to the side of the wheels when starting up.
2. Let the wheels gain maximum speed before starting to grind.
3. Do not grind on the side of the wheel.
4. Small objects must not be held by hand.
5. Workpiece must never be held with gloves, cloth, apron or pliers.
6. Never leave the machine running unattended.
7. Do not bend down near the machine whilst it is running.
8. Never force the workpiece against a wheel.
9. Slowly move the workpiece across the face of the wheel uniformly. Do not use the side of the grinding wheel
to grind workpieces.
10. Coolant spilt on the floor should be immediately cleaned up with absorbent material.

HOUSEKEEPING
1. Switch off the grinder at the end of work and switch off at power point.
2. Check that power leads have not been damaged during use.
3. Clean swarf and leave the machine in a safe, clean and tidy state.

This SOP should be used in conjunction with relevant machinery manuals and manufacturer recommendations.

Procedure Version Effective Date Review Date Page Number Date Printed
Reference
WHS SOP 2 1.0 28/03/2018 28/03/2021 1 24/04/2018
Safe Operating Procedures

POTENTIAL HAZARDS
1. Hot metal – use appropriate tools to manage heat
2. Sparks – fit spark arresters
3. Noise – wear approved hearing protection
4. Eye injury – wear approved eye PPE

SPECIAL NOTE
NO PERSONNEL ARE TO USE THIS EQUIPMENT PRIOR TO OBTAINING:
 COMPETANCY IN THE CORRECT USE OF THE EQUIPMENT
 READING AND FULLY UNDERSTANDING THE OPERATOR’S MANUAL
 READING THE STANDARD OPERATING PROCEDURE
 UNDERGOING THOROUGH PRACTICAL TRAINING WHILE PROPERLY SUPERVISED
 SUPERVISORS TO ENSURE SOP’S ARE SIGNED OFF

All completed SOPs are to be recorded in TRIM Container A17/2181 utilising a TRIM license in your School/Business
Unit. Completed SOPs are to be published on Safety Hub for ongoing utilisation.

Employee Name: ____________________________________________________________________

Employee Signature: _________________________________________ Date: __________________

Supervisor Name: ____________________________________________________________________

Supervisor Signature: _________________________________________ Date: __________________

This SOP should be used in conjunction with relevant machinery manuals and manufacturer recommendations.

Procedure Version Effective Date Review Date Page Number Date Printed
Reference
WHS SOP 2 1.0 28/03/2018 28/03/2021 2 24/04/2018

You might also like