Scribd
Upload
114 views3 pages

Mobile Jammer Circuit: DLD Lab Proposal

This document proposes a mobile jammer circuit project to present a solution for inappropriate cell phone use in restricted areas. It involves designing a simple, low-cost circuit that uses common electronic components like resistors, capacitors, inductors and transistors to generate radio frequencies between 800MHz and 1.4GHz, matching mobile networks, in order to overpower and disrupt user signals. The circuit uses a 555 timer IC to generate the required frequency which is then amplified by a transistor before being transmitted via an antenna to jam cell phone signals within range.

Uploaded by

Ahmad bhatti
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
114 views3 pages

Mobile Jammer Circuit: DLD Lab Proposal

This document proposes a mobile jammer circuit project to present a solution for inappropriate cell phone use in restricted areas. It involves designing a simple, low-cost circuit that uses common electronic components like resistors, capacitors, inductors and transistors to generate radio frequencies between 800MHz and 1.4GHz, matching mobile networks, in order to overpower and disrupt user signals. The circuit uses a 555 timer IC to generate the required frequency which is then amplified by a transistor before being transmitted via an antenna to jam cell phone signals within range.

Uploaded by

Ahmad bhatti
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

DLD LAB PROPOSAL

Mobile Jammer Circuit

Submitted to:

Ma’am Ayesha Mubashira

Submitted by:

Noor Fatima (SP19-BCS-049)

Objective:

Dissimilar cellular systems process signals differently, and yet, all cell-phone networks use radio
signals that can be interrupted or blocked completely. This project highlights the design of a
simple, low-cost mobile phone jammer and aims to present a solution for the problem of
inappropriate use of the cell-phones in restricted and prohibited areas. The main concept of
jamming is the release of signal (noise) of the same frequency used by mobile-service-provider to
overpower and destruct the user signal. The fabrication of the jammer involved uncomplicated
discrete components, resistors, capacitors, inductors, and transistors to generate the required
frequency (noise) and then amplifies the frequency generated to the range of 800 MHZ to 1.4 GHz
to match the frequency of the mobile phone being transmitted by the base station.

Outline

❖ Introduction
❖ Circuit 1: Mobile Jammer Circuit using 555
❖ Components Required
❖ Operation
❖ Diagram
❖ Circuit 2: Simple Mobile Jammer Circuit
❖ Mobile Phone Jammer Circuit Explanation
Introduction

A Mobile Jammer Circuit or a Cell Phone Jammer Circuit is an instrument or device that
can prevent the reception of signals by Mobile Phones. A Mobile Jammer Circuit is an RF
Transmitter, which broadcasts Radio Signals in the same (or similar) frequency range of the
GSM Communication.

Components Required

❖ 555 Timer IC
❖ Resistors – 220Ω x 2, 5.6KΩ, 6.8KΩ, 10KΩ, 82KΩ
❖ Capacitors – 2pF, 3.3pF, 4.7pF, 47pF, 0.1µF, 4.7µF, 47µF
❖ 30pF Trimmer Capacitor
❖ LED
❖ Coils 3 Turn 24 AWG, 4 Turn 24 AWG
❖ Antenna 15 Turn 24 AWG
❖ BF495 Transistor
❖ ON / OFF Switch
❖ 9V Battery

Circuit 1: Mobile Jammer Circuit using 555

Simple Mobile Jammer Circuit Diagram

You might also like