Mulungushi University

SCHOOL OF SCIENCE, ENGINEERING & TECHNOLOGY

Lecturer: Muumbe K. Lweendo

MSc Eng. (Hohai), BEng (Unza), MEIZ, R.Eng
 Roadmap

Reading for today: SOIL COMPACTION

DEPARTMENT OF CIVIL ENGINEERING, MU,2021

 INTRODUCTION

 COMPACTION OF SOIL
 Compaction is a process that
brings about an increase in soil
density or unit weight,
accompanied by a decrease in air
volume. There is usually no
change in water content. The
degree of compaction is measured
by dry unit weight and depends on
the water content and compactive
effort. For a given compactive
effort, the maximum dry unit
weight occurs at optimum water
content

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 THE PURPOSE OF COMPACTION
 Compaction is the application of mechanical energy to the soil to
rearrange the particles and to reduce the void ratio, usually by
driving out air, with the aim of: -
◦ BEFORE CONSTRUCTION
1)decrease voids ratio and permeability, and achieving a state of
increased unit weight, thus reducing potential frost heave,
2)increasing the contact between soil particles and controlling
subsequent moisture content changes to increase the shear
strength and therefore bearing capacity and avoid swelling,
3)increase stiffness and making the soil less subjecting to
settlement under load, especially repeated loading, for example
from traffic.


 These purposes are important when constructing dams, retaining

walls, and roads

DEPARTMENT OF WATER RESOURCES DEVELOPMENT

 THE PURPOSE OF COMPACTION
◦ COMPACTION AS A CONSTRUCTION PROCESS
➢ Compaction is employed in the construction of road
bases, runways, earth dams, embankments and reinforced
earth walls.
➢ In some cases, compaction may be used to prepare a level
surface for building construction. Soil is placed in layers,
typically 75 mm to 450 mm thick. Each layer is compacted
to a specified standard using rollers, vibrators or rammers.

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 increase  Decrease
 unit weight  Void ratio
 Contact between soil  Permeability
 settlement
particles.
 Shear strength.
 Bearing capacity.
 Avoid swelling.
 Stiffness.

DEPARTMENT OF CIVIL ENGINEERING, MU,2021

➢ The compaction characteristics of a soil can be assessed by means of standard laboratory
tests. The soil is compacted in a cylindrical mould using a standard compactive effort
➢ After compaction, the bulk density and water content of the soil are determined and the dry
density calculated.
➢ For a given soil the process is repeated at least five times, the water content of the sample
being increased each time.
➢ Dry density is plotted against water content and a curve of the form shown below is
obtained. This curve shows that there is a particular value of water content, known as the
optimum water content 𝑤𝑜𝑝 , at which a maximum value of dry density is obtained.

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 LABORATORY COMPACTION TESTS

 Standard Proctor Test: -

◦ mould 4.6” * 4” diameter
◦ hammer weight = 5.5 Ib
◦ height of hammer drop = 12” Modified proctor is: -
◦ No. of blows/layer = 25 No.
of layers = 3 •more hammer weight
 •more hammer drop
distance
 Modified Proctor Test: -
◦ mould 4.6” * 4” diameter •more no. of layers
◦ hammer weight = 10 Ib
◦ height of hammer drop = 18”
◦ No. of blows/layer = 25
◦ No. of layers = 5

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

• The aim of the test is to
establish the maximum
d max Zero air voids
dry density that may be
line
attained for a given soil
ZAV

Dry Density
with a standard amount
of compactive effort.
• When a series of Soil too dry and Soil too wet &
brittle deformable
samples of a soil are
compacted at different
OMC
water content the plot
usually shows a distinct Moisture content
peak.
At low values of water content most soils tend to be stiff and are difficult to compact. As the water content is increased the soil becomes more
workable, facilitating compaction and resulting in higher dry densities. At high water contents, however, the dry density decreases with
increasing water content, an increasing proportion of the soil volume being occupied by water
DEPARTMENT OF CIVIL ENGINEERING, MU,2020
 ➢ The maximum possible value of dry density is referred to as the ‘zero air voids’ dry density
or the saturation dry density and can be calculated from the expression:

𝐺𝑠
𝜌𝑑 = 𝜌
1 + 𝑤𝐺𝑠 𝑤

Gs = Specific gravity of soil grains,

𝜌𝑤 = 𝐷𝑒𝑛𝑠𝑖𝑡𝑦 𝑜𝑓 𝑤𝑎𝑡𝑒𝑟
𝑤 = 𝑊𝑎𝑡𝑒𝑟 𝑐𝑜𝑛𝑡𝑒𝑛𝑡
𝜌𝑑 = 𝐷𝑟𝑦 𝐷𝑒𝑛𝑠𝑖𝑡𝑦

➢ The dry density after compaction at water content w to an air content A can be calculated
from the following expression
𝐺𝑠 𝜌𝑊
𝜌𝑑 = (1 − 𝐴)
1 + 𝑤𝐺𝑠

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

➢ The calculated relationship between zero air voids dry density and water content can
be plotted as shown below
➢ The curve is referred to as the zero air voids line or the saturation line.

Dry density–water content curves for different compactive efforts.

DEPARTMENT OF CIVIL ENGINEERING, MU,2020
 FACTORS AFFECTING COMPACTION
A number of factors will affect the degree of
compaction that can be achieved:
1) Nature and type of soil, i.e. sand or clay, grading,
plasticity
2) Water content at the time of compaction
3) Site conditions, e.g. weather, type of site, layer
thickness
4) Compactive effort: type of plant (weight,
vibration, number of passes)

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

  The compactive effort
will be greater when
using a heavier roller
on site or a heavier
rammer in the Modified
Compaction
laboratory. With

Dry Density
greater compactive
effort: Standard
◦ maximum dry density Compaction
increases
◦ optimum water content
decreases
◦ air-voids content Moisture content
remains almost the
same.
The dry density of a given soil after compaction depends on the water content and the energy supplied by the compaction
equipment (referred to as the compactive effort).

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

DEPARTMENT OF CIVIL ENGINEERING, MU,2020
STRUCTURE OF COMPACTED SOIL

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 SHAPES OF COMPACTION CURVE

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 EXPRESSIONS AND CALCULATIONS

A compacted sample is weighed to determine

its mass: M (grams)
The volume of the mould is: V (ml)
Sub-samples are taken to determine the water
content: w

ρd = dry density
ρ = wet density
W = water content

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 Example

In a typical compaction test the following data might

have been collected:
❖Mass of mould, Mo = 1082 g
❖Volume of mould, V = 950 ml
❖Specific gravity of soil grains, Gs = 2.70

Mass of
mould + soil 2833 2979 3080 3092 3064 3027
(g)
Water
8.41 10.62 12.88 14.41 16.59 18.62
content (%)

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 Solution

 Calculated Densities and Density Curve

 The expressions used are:

Bulk density,
1.84 2.00 2.10 2.12 2.09 2.05
 (Mg/m³)

Water
content, w
0.084 0.106 0.129 0.144 0.166 0.186

Dry density,
1.70 1.81 1.86 1.851 1.79 1.73
d (Mg/m³)

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 TESTS OF PERMEABILITY COEFFICIENT - laboratory

Ex/ In a typical compaction test

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 TESTS OF PERMEABILITY COEFFICIENT - laboratory

 Air-voids curves
◦ The expression used is: -

Water content (%) 10 12 14 16 18 20

d when Av = 0% 2.13 2.04 1.96 1.89 1.82 1.75

d when Av = 5% 2.02 1.94 1.86 1.79 1.73 1.67

d when Av = 10% 1.91 1.84 1.76 1.70 1.64 1.58

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 TESTS OF PERMEABILITY COEFFICIENT - laboratory

Air-voids curves
Notes: -
1) In above figure, it will be
seen that the maximum dry
density occurs at about (5
%) air void ratio (or about
85 % - 90 % saturation).
2) At the same point, much of
the air remaining in the soil
is in the form of small
occluded bubbles, entirely
surrounded by water, and
held in position by surface
tension.

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 TESTS OF PERMEABILITY COEFFICIENT - field
 FIELD COMPCATION
 There are three categories of compaction equipments,
namely, rollers, rammers, and vibration.
ROLLERS
A. Smooth-wheeled roller
❖ Self-propelled or towed steel rollers ranging from
❖ 2 - 20 tones
❖ Suitable for: well-graded sands and gravels
silts and clays of low plasticity
❖ Unsuitable for: uniform sands; silty sands; soft clays

B. Grid roller
❖ Towed units with rolls of 30-50 mm bars, with spaces between of 90-100 mm
❖ Masses range from 5-12 tones
❖ Suitable for: well-graded sands; soft rocks; stony soils with fine fractions
❖ Unsuitable for: uniform sands; silty sands; very soft clays

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 TESTS OF PERMEABILITY COEFFICIENT - field
FIELD COMPCATION-ROLLERS
C. Sheeps feet roller
❖ Also known as a 'tamping roller'
❖ Self propelled or towed units, with hollow drum
fitted with projecting club-shaped 'feet'
❖ Mass range from 5-8 tonnes
❖ Suitable for: fine grained soils; sands and gravels,
with >20% fines
❖ Unsuitable for: very coarse soils; uniform gravels

D. Pneumatic-tyred roller
❖Usually a container on two axles, with rubber-tyred wheels.
❖Wheels aligned to give a full-width rolled track.
❖Dead loads are added to give masses of 12-40 tonnes.
❖Suitable for: most coarse and fine soils.
❖Unsuitable for: very soft clay; highly variable soils.

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 TESTS OF PERMEABILITY COEFFICIENT - field

FIELD COMPCATION
 Power rammer
❖Also called a 'trench tamper'
❖Hand-guided pneumatic tamper
❖Suitable for: trench back-fill; work in confined areas
❖Unsuitable for: large volume work

Vibrating plate
❖ Range from hand-guided machines to larger roller
combinations
❖ Suitable for: most soils with low to moderate fines
content
❖ Unsuitable for: large volume work; wet clayey soils

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 FIELD DENSITY TESTS

1) Sand – Cone Method:

❖ Using Ottawa sand passing sieve No. 20 and
retained on sieve No. 30.
2) Core – Cutter method:
❖ Insert a standard cylinder in soil then get it out with
soil sample to calculate the density.
3) Standard Penetration Test (SPT)
4) Balloon – Density Method

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 Additional Methods to Determine the (k)

Hole prepared - plan

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 Additional Methods to Determine the (k)

CONTROL OF COMPACTION (Compaction Quality): -

The degree of compaction achievable on site depends mainly on:
· Compactive effort: type of plant + No of passes
· Water content: can be increased if dry, but vice-versa
· Type of soil: higher densities with well-graded soils; fine soils have
higher water

To check the field density with respect to standard or modified Proctor

density, we calculate “Degree of Compaction (D.C.)” or called relative
compaction and it is equal to: -

 d in field
D.C. = *100  (90 – 95) %
 d max . in laboratory

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

EMPIRICAL EQUATION OF COEFFICIENT OF PERMEABILITY:
-

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

Nuclear density meter

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

Q1: a contractor has compacted the base course for a new road and found that
the average values of test samples show the water content of 14.6%, specific
gravity of 2.81, and the unit weight of 18.2 kN/m3. Knowing that the
specifications require that the void ratio ≤ 0.80, has the contractor complied
with the specifications?

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 STRATIFIED SOIL AND PERMEABILITY

Q2: It is decided to use the sand soil in construction of an embankment for the road around Kabwe
town. The soil properties of the hill are, total unit weight of 18 kN/m3, water content of 30%,
specific gravity of 2.65, and the maximum dry unit weight of 15.07 kN/m3 and optimum moisture
content of 32%. The characteristics of the embankment are: degree of compaction of >95%, the
embankment will be in a trapezoidal shape with dimensions of 16m in the width of the top level,
1m in the height, and the side slope of 2:1. What is the volume in (m3) of the soil from the hill
needed to construct the embankment? Find the dry unit weight, saturation, void ratio, porosity for
the hill and embankment. What are the effective considerations in the construction of the
embankment? Estate the formula used to classify the sand soil according to density. Give the range
of the classification. What is the suitable method to examine the coefficient of permeability of the
origin soil? Why, derive it.
Length=1000m
Top Level

Height Embankment
2

DEPARTMENT OF CIVIL ENGINEERING, MU,2020

 End of Presentation
Thank you for listening …
Contact details of presenter: [email protected]

DEPARTMENT OF CIVIL ENGINEERING, MU,2020