Helium-Neon Laser Series

Laser Models 1100, 1000, and 1500 Series

Power Supplies 1200 and OEM Series
User’s Manual
 ECO-066866
945-002, REV 503 NOVEMBER 2018

The products described in this manual are based on Lumentum intellectual property, which
includes more than 1,800 United States and foreign registered patents. These patents are
relevant to an extensive set of products and/or technology applications, including Lumentum
laser products and associated technologies. For further information, contact the Lumentum
Legal Department.

945-002 Rev503
Contact Information
Thank you for purchasing this Lumentum product. We are confident this product will serve
you well. Any comments or questions you have concerning our product or your application are
encouraged. Please contact your local sales representative or us directly, toll-free, at:

Telephone

APAC 800 0825-LITE (+800 0825-5483)

China 10 400 120-LITE (+10 400 120-5483)
EMEA 800 0000-LITE (+800 0000-5483)
North America 1 844 810-LITE (1 844 810-5483)

Fax

APAC 800 0010-LITE (+800 0010-5483)

China 10 400 121-5483
EMEA 800 0010-LITE (+800 0000-5483)
North America 1 844 910-5483

If you have issues using these toll-free numbers, please contact

[email protected] or call 1 613-843-5378
Internet: www.lumentum.com

Headquarters
Lumentum Operations LLC
400 N. McCarthy Blvd.
Milpitas, CA 95035
USA.

ii

945-002 Rev503
Table of Contents
1 SAFETY INFORMATION, INSTRUCTIONS, AND SYMBOLS ..................................................................... 1
1.1 ALERT MESSAGES .................................................................................................................. 1
1.2 SAFETY SYMBOLS .................................................................................................................. 1
1.3 SAFETY SUMMARY ................................................................................................................. 2
1.4 CONDITIONS OF ACCEPTABILITY SAFETY SYMBOLS ............................................................. 2
1.5 SAFETY INSPECTION INSTRUCTIONS ...................................................................................... 3
1.5.1 BEFORE INITIALIZING AND OPERATING THE UNIT ................................................ 3
1.6 GENERAL SAFETY GUIDELINES ............................................................................................. 3
1.7 ELECTRICAL SAFETY INFORMATION ...................................................................................... 6
1.7.1 CLASSIFICATION .................................................................................................... 6
1.7.2 DISCONNECTING FROM LINE POWER ..................................................................... 6
1.7.3 LINE POWER REQUIREMENTS ................................................................................ 7
1.7.4 FUSE TYPE.............................................................................................................. 7
1.8 COMPLIANCE .......................................................................................................................... 7
1.8.1 FDA-CDRH COMPLIANCE .................................................................................... 7
1.8.2 IEC COMPLIANCE .................................................................................................. 7
1.8.3 SAFETY LABELS ..................................................................................................... 8

2 GENERAL INFORMATION AND SPECIFICATIONS ................................................................................ 10

2.1 GENERAL INFORMATION ...................................................................................................... 10
2.1.1 PROTECTIVE HOUSING ............................................................................................. 10
2.1.2 KEY CONTROL ..................................................................................................... 10
2.1.3 KEY FEATURES .................................................................................................... 10
2.1.4 APPLICATIONS...................................................................................................... 11
2.1.5 STANDARD ACCESSORIES .................................................................................... 11
2.1.6 OPTIONAL ACCESSORIES ..................................................................................... 11
2.2 SPECIFICATIONS ................................................................................................................... 11
2.2.1 MODEL 1100 SERIES SPECIFICATIONS ................................................................. 11
2.2.2 MODEL 1500 SERIES NOVETTE SPECIFICATIONS ................................................. 14
2.2.3 MODEL 1000 SERIES SPECIFICATIONS ................................................................. 17
2.2.4 OTHER SPECIFICATIONS……………………………………………………..18

3 GETTING STARTED ............................................................................................................................ 19

3.1 BEFORE INITIALIZING AND OPERATING THE UNIT............................................................... 19
3.2 INITIAL INSPECTION ............................................................................................................. 19
3.3 OPERATING ENVIRONMENT ................................................................................................. 20
3.3.1 TEMPERATURE ..................................................................................................... 20
3.3.2 HUMIDITY ............................................................................................................ 20
3.4 STORING AND SHIPPING ....................................................................................................... 20
3.4.1 CLAIMS AND REPACKAGING ................................................................................ 20
3.4.2 RETURNING SHIPMENTS TO LUMENTUM ............................................................. 21

4 OPERATING AND MAINTENANCE INSTRUCTIONS .............................................................................. 22

4.1 LASER HEADS AND POWER SUPPLY..................................................................................... 22
4.2 INITIALIZING THE LASER ...................................................................................................... 22

iii

945-002 Rev503
 4.3 TROUBLESHOOTING ............................................................................................................. 23
4.4 CALIBRATING THE UNIT....................................................................................................... 24

5 POWER SUPPLIES .......................................................................................................................... 22

5.1 MODEL 1200 SERIES POWER SUPPLY .............................................................................. 22
5.2 OEM SERIES POWER SUPPLY............................................................................................. 22

6 APPENDIX ……………………………………………………………………………….. …… 34
6.1 1100 LASERS HOUSING CONFIGURATION ……………………………….………..34
6.2 OEMs AC WIRING GUIDANCE ………………………………………………………35

List of Tables
TABLE 1: SAFETY SYMBOLS ......................................................................................................................... 1
TABLE 2: LASER SAFETY LABELS ................................................................................................................. 9
TABLE 3: MODEL 1100 SERIES SPECIFICATIONS ................................. ERROR! BOOKMARK NOT DEFINED.
TABLE 4: MODEL 1500 SERIES NOVETTE SPECIFICATIONS ................. ERROR! BOOKMARK NOT DEFINED.
TABLE 5: NOVETTE 1500 SERIES AND INPUT VOLTAGES ............... ERROR! BOOKMARK NOT DEFINED.
TABLE 6: MODEL 1000 SERIES HENE TUBE SPECIFICATIONS............... ERROR! BOOKMARK NOT DEFINED.
TABLE 7: OTHER SPECIFICATIONS FOR MODELS 1100, 1500, AND 1600ERROR! BOOKMARK NOT
DEFINED.
TABLE 8: 1200 MODEL SELECTION FOR 1100 SERIES HEAD. ............ ERROR! BOOKMARK NOT DEFINED.7
TABLE 9: 101T MODELS ........................................................................................................................... 29
TABLE 10: 314T MODELS ......................................................................................................................... 30
TABLE 11: 380T MODELS ......................................................................................................................... 31
TABLE 12: OEM MODEL SELECTION .................................................................................................... 32
TABLE 13: OTHER OEM MODELS ……………………………………………………….…… …….33
TABLE 14: MODEL 1100 DIMENSIONS ………………………………………………………………34
TABLE 15: OEM POWER SUPPLY AC INPUTS ………………………………………..……………35

List of Figures
FIGURE 1: PLACEMENT OF SAFETY LABELS ON 1100 LASERS ...................................................................... 9

iv

945-002 Rev503
FIGURE 2: PLACEMENT OF SAFETY LABELS ON 1500 LASERS ...................................................................... 9
FIGURE 3: HELIUM-NEON LASER SYSTEMS ................................................................................................ 10
FIGURE 4: MODEL 1100 SERIES ACCESSORY BEZELS................................................................................. 13
FIGURE 5: MODEL 1500 SERIES LASERS (DIMENSIONS IN INCHES)............................................................. 15
FIGURE 6: MODEL 1500 SERIES LASER BOTTOM PLATE SLOT MOUNT .............................................. 15
FIGURE 7: MODEL 1500 SERIES POWER SUPPLY DIMENSIONS........................................................... 16
FIGURE 8: MODEL 1500 SERIES POWER SUPPLY INPUT 230VAC CORDERROR! BOOKMARK NOT
DEFINED.
FIGURE 9: MODEL 1500 SERIES POWER SUPPLY INPUT 100, 120 VAC CORDERROR! BOOKMARK
NOT DEFINED.
FIGURE 10: SMALL MODEL 1200 SERIES POWER SUPPLY DIMENSIONSERROR! BOOKMARK NOT
DEFINED.
FIGURE 11: LARGE MODEL 1200 SERIES POWER SUPPLY DIMENSIONSERROR! BOOKMARK NOT
DEFINED.
FIGURE 12: MODEL 101T SERIES POWER SUPPLY DIMENSIONS ....................................................... 30
FIGURE 13: MODEL 314T SERIES POWER SUPPLY DIMENSIONS ERROR! BOOKMARK NOT DEFINED.
FIGURE 14: MODEL 380T SERIES POWER SUPPLY DIMENSIONS ....................................................... 32
FIGURE 15: MODEL 1100 SERIES HOUSING CONFIGURATION ………………………………….33

945-002 Rev503
Preface
Thank you for purchasing the Lumentum Helium-Neon Series laser.
The Lumentum 1100, 1000, and 1500 Series red Helium-Neon laser products offer low noise,
high power stability, and long life for the most demanding applications.
With more than 1.5 million units sold, Lumentum Helium-Neon lasers are the industry
standard for many advanced system designs.

Our close-cathode design rapidly and uniformly distributes discharge heat throughout the
laser, resulting in excellent thermal, beam-pointing, and power stability.
Our field concentrator design ignites the discharge within milliseconds of applying the start
voltage.
Hard-sealed internal mirrors, small physical size, and low noise result in greater reliability,
longer life, and enhanced performance.

About This Manual

Information contained herein is deemed to be reliable and accurate. No responsibility is
assumed for its use or for any infringements on the rights of others. Lumentum reserves the
right to change the design, specifications, etc. of the products described at any time without
notice. If you have questions or comments about any part of this manual, please call Lumentum
at the contact information provided on the previous pages.

Copyright 2018Lumentum. All rights reserved.

Last Revision: November 2018

vi

945-002 Rev503
1 Safety Information, Instructions, and Symbols
1.1 Alert Messages
The cautions and warnings used throughout this manual are explained below. Read
this section carefully before operating the laser for the first time

Warning
A Warning message indicates a nearby hazard that, if not avoided, may
result in serious injury or property damage.
Note
A Note provides information about installation, operation, or maintenance of
the system that is important to know but is not necessarily hazardous. Notes
also provide instructions or company policy for the protection of property,
safe work practices, reminders of proper safety procedures, or the location
of safety equipment.

Read Manual. Identifies particular instructions, procedures, or

manuals that must be read before continuation with a task.

Laser Safety Eyewear. Identifies an operation that requires any user

to wear approved laser-safety eyewear.

1.2 Safety Symbols

The following symbols may be marked on the units (Table 1). Observe all safety
instructions that are associated with a symbol.
Symbol Description
Laser safety. See the user’s manual for instructions on handling and
operating the unit safely.

General hazard. Identifies a set of recognizable conditions with the

potential for initiating an event that could result in death, injury, or
illness to people or damage to facility or equipment.

Electrical hazard. Identifies a potential electrical shock or burn hazard

from electrical voltages.

Table 1: Safety Symbols

1
 1.3 Safety Summary

Note
The cautions and warnings used throughout this manual are
explained below. Read this section carefully before operating the
laser for the first time.

The 1100, 1000, and 1500 Helium-Neon (HeNe) lasers can be Class II, IIIA, or IIIb
lasers, as defined by the USA Code of Federal Regulation (CFR) 21 CFR 1040.10
Laser Safety Standard, or Class 2M, 3R or 3B, as defined by the EN 60825-1
European standard.

The lasers are original equipment manufacturer (OEM) components, designed for
integration, and, as such, they do not fully comply with the laser safety requirements
of either 21 CFR 1040.10 or EN 60825-1.

The laser safety standards require that certain laser safety features be provided on the
end-product or system. The end-user is responsible for adding those.

The following is a summary of the HeNe 1100, 1000 Series lasers Compliance
Conditions of Acceptability.

1.4 Conditions of Acceptability Safety Symbols

The 1100 and 1000 Series lasers are OEM or system components, and, as such, are
only intended for integration into other equipment, not as a stand-alone system.
This product is an equipment component. It does not fully comply with all electrical
or laser safety requirements that are applicable to a stand-alone system or
equipment.
When this laser is installed in the end-product, the end-user must provide
consideration to the following:
1 All electrical safety features or the protection enclosure shall be provided in
the end-product, as required by IEC61010-1 or any other applicable electrical
safety regulations.
2 All laser safety features and indicators, as required by 21 CFR 1040.10 or
EN60825-1 or any other applicable laser safety standards, shall be provided
by the end-user.

945-002 Rev503
 3 The following statement shall be included in the end-product
instruction/installation manual if adjustments or controls are accessible to
the user or operator of the final product.
"CAUTION – Use of controls, adjustments, or performance of
procedures other than those specified herein may result in
hazardous radiation exposure."
4 The product's thermal circuitry shall be evaluated in the end-product.
5 Compliance with the FDA-CDRH laser product requirements and safety
standards shall be determined and provided in the end-user application.
6 The end-user is required to provide information about the limit values of
the materials to be processed, the fumes, and the particulate matter
generated by machining these materials and their removal requirements.

1.5 Safety Inspection Instructions

The following safety instructions must be observed whenever the unit is operated,
serviced, or repaired. Failure to comply with any of these instructions or with any
precaution or warning contained in the user’s manual is in direct violation of the
standards of design, manufacture, and intended use of the unit. Lumentum assumes
no liability for the customer’s failure to comply with any of these safety requirements.

1.5.1 Before Initializing and Operating the Unit

 Inspect the unit for any signs of damage and read the user’s manual thoroughly.
 Install the unit as specified in the 3. Getting Started section.
 Ensure that the unit and any devices or cords connected to it are properly
grounded.

1.6 General Safety Guidelines

It is recommended that all persons who use, or are near, lasers be aware of the
potential hazards.

945-002 Rev503
 Warning

VISIBLE RADIATION.

AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED

RADIATION. NEVER LOOK INTO THE BEAM PATH. KEEP ALL
BODY PARTS AND REFLECTIVE MATERIALS OUT OF THE BEAM
PATH.

The free space HeNe Series lasers can be either Class 2M, 3R, or
3B laser sources.

• The Class 3B lasers can have a maximum rated output power

of 25mW CW at wavelengths of 633nm.

• The Class 3R lasers can have a maximum rated output power

of 3.2mW CW at wavelengths of 633nm.

• The Class 2M lasers can have a maximum rated output power

of 0.7mW CW at wavelengths of 633nm.

Exposure to the laser beams must be avoided.

Some, but not all, potential human hazards include permanent loss
of vision and/or subsurface skin damage.

Warning

• THE STARTING AND OPERATING VOLTAGES OF THE

LASER HEADS ARE LETHAL AND ARE SPECIFIED HEREIN.
IF ACCESS TO A POWER SUPPLY IS NECESSARY, ENSURE
THAT THE POWER SUPPLY IS TURNED OFF AND
UNPLUGGED.

• If it is necessary to operate the laser head while a power

supply is exposed, extreme caution is advised to avoid
exposure to high voltages and only licensed personnel
should do it.

945-002 Rev503
 Warning

• Operating the lasers in the presence of flammable gases or

fumes is extremely hazardous.

• Provide protective eyewear suitable for the output wavelength

of your laser. Control all beam reflections.

• Laser glasses may not provide enough protection if a very

powerful beam is viewed directly.

• Post the area with laser safety warning signs. Ensure that no
beams are emitted through windows, doors, etc.

• Operate the laser only under the direct supervision of a

person knowledgeable in laser safety. Limit access to the
laser area by spectators unless supervised.

• Do not mount the laser at or near eye level for a person in the
standing or sitting position; enclose beam paths whenever
possible.

• Attenuate laser power to a low level to minimize the intensity

of accidental stray reflections or refractions when aligning a
chain of optical components in the laser beam.

• Never leave the laser on and unattended.

• If the laser power supply has a key switch on a front panel,

the key must be inserted and turned to enable the laser to
operate. The key is captive in the operational position.
Remove the key when the laser is not in use or unattended.
Store the key in a safe place.

945-002 Rev503
 Note

HeNe Series lasers should not be operated unless all appropriate

safety precautions are taken. These include, but are not limited to:

• Wearing protective safety glasses by all people in the vicinity of

the laser system;
• Installing warning lights, signs, safety screens and/or curtains;
• Implementing a safety interlock so the laser shuts down if
someone unexpectedly enters an area containing the laser; and
• Containing the beam to eliminate or minimize the possibility of
exposure to the beam.

1.7 Electrical Safety Information

Warning
NEVER TOUCH A LASER CABLE WHEN ITS POWER
SUPPLY IS ON.
• A laser requires a high voltage start pulse of about 10,000 volts.
The normal operating voltage of a laser exceeds 1,000 volts and
can be as high as 4,000volts.
• A residual high voltage can exist on the cables leading from the
power supply to the laser after the power supply is turned OFF.
Wait at least 10 secs after turning it OFF before manipulating
them.

1.7.1 Classification
The 1100s laser consists of an anodized metal chassis that is internally connected
directly to earth via a power cord and, therefore, is classified as a Class 1
instrument. Class 1 refers to equipment relying on ground protection as a means
of shock protection.

Use only the type of power cord supplied with a 1200 Series power supply.
Connect the power cord only to a power outlet equipped with a protective earth
contact. Never connect to an extension cord that is not equipped with this feature.

Disconnect the power cord from a 1200 power supply before adding or removing
any components. Do not rely solely on electrical safety devices or interlocks

1.7.2 Disconnecting from Line Power

945-002 Rev503
 Some of the power supply circuits are powered whenever the unit is connected to
the AC power source (line power). To ensure that the unit is not connected to the
line power, disconnect the power cord from the AC line-power source
(receptacle). The power cord must always be accessible from this point. If the
unit is installed in a cabinet, the operator must be able to disconnect the unit from
the line power by the system’s line-power switch.

1.7.3 Line Power Requirements

The 1200s power supply can operate from any single-phase AC power source that
supplies between 100 and 230 VAC at a frequency range of 50 to 60 Hz. The
exact maximum power consumption is dependent on the configuration of each
system. Typically is less than 30VA

1.7.4 Fuse Type

The fuse type used by the 1200s power supply is dependent on the configuration
of each system.

1.8 Compliance

1.8.1 FDA-CDRH Compliance

Under the US FDA CDRH, Lumentum lasers comply with the CFR, Title 21,
Subchapter J, which pertains to laser safety and labeling. See
http://www.fda.govfor more information.
Lumentum offers two versions of lasers as certified by the US FDA CDRH. These
versions are CDRH certified and non-CDRH certified, as follows:
• The CDRH 1500s laser version complies with CDRH requirements. The
CDRH accession number is 9620546. This version can be used as a stand-
alone instrument.
• The non-CDRH 1100s, 11000s certified versions are only for OEM customers
who integrate the laser into their instruments. The customer is responsible for
CDRH certification of their instrument.

1.8.2 Safety Compliance

The 1100s and 1500s lasers adhere to the International Electro technical Commission
IEC standard 60825-1:2014 concerning laser safety, and IEC standard 61010-1.
They also carry the US, Canadian UL mark, the TUV SUD mark.

945-002 Rev503
 1.8.3 Safety Labels
The following sample safety labels are affixed to the outside of the HeNe Series
lasers and are not to be removed either prior to or after installation.
Serial Number
Label 1 Label

Label 2 Warning- Class 2M

Explanatory -
2 Aperture Label

Class 3R <4mW

Class 3B <10mW

Class 3B <20mW

945-002 Rev503
 Class 3B <35mW

Table 2: Laser Safety Labels

A typical placement of required laser safety labels is shown in Figures 1 and 2.

Figure 1: Placement of Safety Labels on 1100 Lasers

Figure 2: Placement of Safety Labels on 1500s Laser

945-002 Rev503
 The lasers also comply with the China RoHS, RoHS and WEEE European Directives.

2 General Information and Specifications

2.1 General Information
This user’s manual for the Model 1100 Series, Model 1000 Series, and Model 1500
Series Helium-Neon Laser contains complete operating instructions. Each laser is
available as a component for OEM or as CDRH-compliant 1500 self-contained
system. Various compatible AC and DC power supplies are available for each laser,
and an optional AC/DC universal supply is available for the Model 1500 Novette™
system.

Figure 3 shows a 1200 power supply, Model 1100 lasers, Model 1000 laser tubes,
and the Model 1500 laser system.

Figure 3: Helium-Neon Laser Systems

2.1.1 Protective Housing

The housing of the 1100 and 1500 lasers is designed to prevent collateral radiation
in excess of admissible limits, as well as laser radiation in excess of the accessible
emission limits.

2.1.2 Key Control

The AC power supply is activated when the key is turned to the “ON” position.
A three-second time delay occurs before the laser is activated. The key cannot be
removed when turned to the “ON” position.

2.1.3 Key Features

• Long operating life

10

945-002 Rev503
 • Low noise
• Hard-sealed internal mirrors
• Excellent beam-pointing stability
• Long-term amplitude stability
• Small package

2.1.4 Applications
• Hand-held bar code scanning
• Laboratory use in polarization experiments
• DNA sequencing
• Flow cytophotometry
• Hematology
• Confocal microscopy
• Semiconductor inspection
• High-speed printing
• Photo processing

2.1.5 Standard Accessories

• 1100 lasers have a fixed laser head cable
• 1500s have a Universal AC/DC power supply.
• User’s manual

2.1.6 Optional Accessories

• 100/120, 120, or 220 V AC power supply
• Optical adapter for Model 1500 Series
• Accessory bezels for Model 1100 Series

2.2 Specifications

2.2.1 Model 1100 Series Specifications

The Model 1100 Series helium-neon laser consists of a packaged head with
Alden-type or equivalent connectors. The Model 1100 Series laser head is
compatible with the Model 1200 power supply, available in either 100/120 or 220
V AC configurations.

Table 3 lists the specifications for Model 1100 Series packaged laser heads.
Beam parameters are guaranteed at the Far Field.

The coherence length of the HeNe lasers is typically between 20 and 28cm.

11

945-002 Rev503
 1101 1103 1107 1108 1122 1125 1135 1137 1144 1145 102 196
Specifications
1101P 1103P 1107P 1108P 1122P 1125P 1135P 1137P 1144P 1145P

Mini output
1.5 2 0.8 0.5 2 5 10 7 17 25/22 2 1.5
power (mW)
Beam
0.63 0.63 0.48 0.48 0.63 0.81 0.68 0.81 0.7 0.7 0.63 0.49
diameter (mm)
Beam
divergence 1.3 1.3 1.7 1.8 1.3 1 1.2 1 1.15 1.15 1.3 1.6
(mrad)
Beam pointing
stability (mrad)
n/a n/a n/a n/a <0.10 <0.10 <0.20 <0.10 <0.20 <0.20 <0.10 <0.10
25 °C cold
start
Beam pointing
stability (mrad)
n/a n/a n/a n/a <0.02 <0.02 <0.02 <0.02 <0.03 <0.03 <0.03 <0.03
15min warm-
up
1
Min
polarization 500:1 500:1 500:1 500:1 500:1 500:1 500:1 500:1 500:1 500:1 n/a n/a
ratio
Longitudinal
mode spacing
730 730 1090 1090 730 435 320 435 257 257 637 637
(MHz)
nominal
Max mode
sweeping's 3% 3% 10% 20% 3% 2% 2% 2% 1% 1% <5% <5%
ripple
2
Max noise
30-10MHz 0.1% 0.1% 0.1% 0.1% 0.1% 0.2% 1.0% 0.2% 1.0% 1.0% 1.0% 1.0%
(rms)
Max power
±2.5% ±2.5% ±2.5% ±2.5% ±2.5% ±2.5% ±3.0% ±2.5% ±2.0% ±2.0% ±2.5% ±2.5%
drift over 8 hrs
Maxi warm-up
time (min), 10 10 10 10 10 10 15 10 20 20 10 10
to 95% power
Operating
voltage 1700 1700 1350 1350 1800 2350 3100 2450 3800 3800 1550 1550
(VDC±100 )
Operating
6.0- 6.0-
current (mA 4.9 4.9 4 4 6.5 6.5 6.5 6.5 4.5 4.5
6.5 6.5
±0.1)
Max starting
voltage (KV 10 10 7 7 10 10 10 10 10 10 10 10
DC)
II, IIIa
Class CDRH / IIIa / IIIa / IIIa / IIIb / IIIb / IIIb / IIIb / IIIa / IIIa /
/ 2M, II / 2M IIIb
IEC 3R 3R 3R 3B 3B 3B 3B 3R 3R
3R
1
Polarized version only.
2
When used in conjunction with Lumentum Model 1200 Series power supply.

Table 3: Model 1100 Series Specifications.

12

945-002 Rev503
 The Model 1100 Series, excluding models 1101, 1103, 1107, and 1108, has a
static alignment of the following values:
• Centered to outer cylinder within 0.025 cm (0.01 in)
• Parallel to outer cylinder within 1 mrad.

The Model 1100 Series accessory bezels are shown in 4.

Figure 4: Model 1100 Series Accessory Bezels

13

945-002 Rev503
 2.2.2 Model 1500 Series Novette Specifications
Model 1500 Series NovetteTM helium-neon laser self-contained systems
incorporate a hard-sealed, internal mirror, plasma tube, and a power module. The
packages are compact and self-contained.

Table 4 lists the specifications for Model 1500 Series systems.

Beam parameters are guaranteed at the Far Field.

Specification 1507/1507P 1508/1508P

Minimum output power (TEM00, 633 nm) 0.80 mW 0.50 mW
Wavelength 633 nm

Beam diameter (TEM00, 1/e2 points ±3%) 0.48 mm

Beam divergence (TEM00, ±3%) 1.7 mrad
1 Minimum polarization ratio (P versions) N/A 500:1
Longitudinal mode spacing 1090 MHz
2 Maximum noise (30 Hz to 10 MHz) 1.0% rms
Maximum drift with respect to mean power, ±2.5%
over 8 h
Maximum mode sweeping contribution 10% 20%
Maximum warm-up time (minutes to 95% 10
power)
Operating current (at 120 V AC) 150 mA AC
Operating current (at 200 V AC) 82 mA AC
Expected operating lifetime >12,000 hrs
Weight 1.81 kg (4 lb)
CDRH Class IIIa II
IEC 60825-1 Class 3R 2M
1 TEM00 version only.
2 When used with Lumentum Model 1200 Series power supply.

Table 4: Model 1500 Series NovetteTM Specifications

14

945-002 Rev503
 Figure 5 shows the Model 1500 Series typical dimensions.

Figure 5: Model 1500 Series Laser (dimensions in inches)

The base plate of the NovetteTM is slotted for mounting As shown in Figure 6.
The head of a standard Socket Head Cap screw can be inserted on that slot and
fastened the laser to standard adapters to an optical bench.

Figure 6: Model 1500 Series Bottom Plate Slot Mount

15

945-002 Rev503
 The Model 1500 Series NovetteTM includes an external Universal AC/DC power
supply which provides 12VDC to the 1500 laser input.

Figure 7: Model 1500 Series Power Supply Dimensions

The 1500 series is made in two versions, input power 100/120VAC and 220VAC.

Model Minimum Rated Output Power 100/ 120 V AC 220 V AC

1507 0.8 mW, random polarization 1507-1 1507-2
1507P 0.8 mW, linear polarization 1507P-1 1507P-2
1508 0.5 mW, random polarization 1508-1 1508-2
1508P 0.5 mW, linear polarization 1508P-1 1508P-2

Table 5: Novette TM 1500 Series and Input Voltages

16

945-002 Rev503
 2.2.3 Model 1000 Series Specifications
The Model 1000 Series helium-neon laser are coaxial plasma tubes with a hard-
sealed internal mirror. They feature improved thermal distribution for superior
beam pointing and power stability. Small physical size and low noise are
characteristics that give the OEM system designer greater flexibility.
Table 5 lists the specifications for Model 1000 Series HeNe tubes.
Beam parameters are guaranteed at the Far Field.

1001 1003 1007 1008 1022 098-0 098-2 098-3

Specifications
1001P 1003P 1007P 1008P 1022P
Mini output power
1.5 2 0.8 0.5 2 1 2 2
(mW)
Beam diameter
0.63 0.63 0.48 0.48 0.63 0.75 0.49 0.49
(mm)
Beam divergence
1.3 1.3 1.7 1.7 1.3 2.7 1.6 1.6
(mrad)
*
Min polarization
500:1 500:1 500:1 500:1 500:1 638 638 638
ratio
Longitudinal mode
spacing (MHz) 730 730 1090 1090 730 637 637 637
nominal
Max mode
3% 3% 10% 20% 3% 5% 10% 5%
sweeping's ripple
**
Max noise 30-
0.1% 0.1% 0.1% 0.1% 0.1% 0.5% 0.5% 0.5%
10MHz (rms)
Max power drift
±2.5% ±2.5% ±5% ±5% ±2.5% ±5% ±5% ±5%
over 8 hrs
Maxi warm-up
time (min) 10 10 10 10 10 15 15 15
up to 95% power
Operating voltage
1300 1300 1000 1000 1300 1000 1200 1200
(VDC±100 )
Operating current
4.9 4.9 4 4 6.5 3.7 3.7 4.5
(mA ±0.1)
Max starting
10 10 7 7 10 8 12 10
voltage (KV DC)
Class CDRH / II, IIIa /
IIIa / 3R IIIa / 3R 2M, 3R
II / 2M IIIa / 3R IIIb / 3B IIIb / 3B IIIb / 3B
IEC
1 TEM00 version only.
2 When used with Lumentum Model 1200 Series power supply.

Table 6: Model 1000 Series HeNe Tube Specifications

17

945-002 Rev503
 2.2.4 Other Specifications
Table 7 summarizes Physical and Environmental specifications for each of the
model series. Where a range is given, the values indicate the specifications of
more than one model within the series.

Specification Model 1100 Series Model 1500 Model 1000 Series

Series Novette
Physical
Dimensions (L) 17.8 to 63.5 cm WxHxL 40.1 to 48.6 cm
(7.0 to 25.0 in) 5.1x6.35x17.8 cm (15.79 to 19.13 in)
2.0x2,5x7.0 in
Weight 3.2 to 4.5 kg 1.8 kg 3.7 to 4.1 kg
(7 to 10 lb) (4 lb) (8 to 9 lb)
Environmental
Operating temperature -29 to 47 °C 0 to 35 °C -20 to 47 °C
(-20 to 117 °F) (32 to 95 °F) (-40 to 158 °F)
Storage temperature -40 to 150 °C -40 to 70 °C -40 to 150 °C
(-40 to 302 °F) (-40 to 158 °F) (-40 to 302 °F)
Humidity 0 to 95% RH 0 to 95% RH 0 to 95% RH
non-condensing non-condensing non-condensing
Operating altitude 0 to 3048 m 0 to 3048 m 0 to 3048 m
(0 to 10,000 ft) (0 to 10,000 ft) (0 to 10,000 ft)
Storage altitude 0 to 21,336 m 0 to 21,336 m 0 to 21,336 m
(0 to 70,000 ft) (0 to 70,000 ft) (0 to 70,000 ft)
Shock (reliability purposes 25 g for 11 ms 25 g for 11 ms 25 g for 11 ms
only) 100 g for 1 ms 100 g for 1 ms 100 g for 1 ms
Drop Test 1 Per IEC61010-1 Per IEC61010-1 1 Per IEC61010-1
1: Drops of over 10mm can slightly mis align the laser mirrors with subsequent loss of
power and/beam performance.

Table 7. Other Specifications for Models 1100, 1500, and 1000

18

945-002 Rev503
3 Getting Started
The Model 1100 Series helium-neon laser requires a high DC voltage current regulated
power supply, with an Alden-type or equivalent connectors.
The power supply Model 1200 Series provides a safer way to energize a 1100 laser.

The Model 1500 Series Novette TM helium-neon laser system requires an external 12V DC
AC converter.

Warning

LASERS REQUIRE SPECIAL HANDLING

HeNe lasers are fragile devices, mostly made out of glass.
A laser requires a sensitive alignment to obtain the desired optical
specifications.
A shock to a laser equivalent to dropping a laser from a 1 cm height may
immediately misalign a laser, degrading the laser power and other
relevant beam specifications. Sometimes disabling the laser entirely.

3.1 Before Initializing and Operating the Unit

 Inspect the unit for any signs of damage.

 Read the user’s manual thoroughly and become familiar with all safety symbols
and instructions to ensure that the unit is operated and maintained safely.

3.2 Initial Inspection

Warning
To avoid electrical shock, do not initialize or operate any unit if it bears
any sign of damage to any portion of its exterior surface, such as the outer
cover or panels.

Check that the unit and contents are complete:

1. Wear an anti-static wrist strap and work in an electrostatic discharge (ESD)

controlled area.

2. Inspect the shipping container for any indication of excessive shock to the
contents and inspect the contents to ensure that the shipment is complete.

3. Inspect the unit for structural damage that may have occurred during shipping.

19
 4. Keep the packaging.
Immediately inform Lumentum and, if necessary, the carrier if the contents of the
shipment are incomplete, if the unit or any of its components are damaged or
defective, or if the unit does not pass the initial inspection.

3.3 Operating Environment

In order for the unit to meet the warranted specifications, the operating environment
must meet the following conditions for temperature, humidity, and ventilation.

3.3.1 Temperature
The Model 1100 and 1000 series lasers can be operated in the temperature range
of -29 to 47 °C (-20 to 117 °F). Model 1500 series units can be operated in the
temperature range of 0 to 35 °C (32 to 95 °F).

3.3.2 Humidity
The unit can be operated in environments with up to 95% humidity non-
condensing. Do not expose it to any environmental conditions or changes to
environmental conditions that can cause condensation to form inside the unit.

Warning
DO NOT USE THE LASER OUTDOORS
To prevent potential fire or shock hazard, do not expose the unit to any
source of excessive moisture.

3.4 Storing and Shipping

To maintain optimum operating reliability, do not store the Model 1100 or Model
1000 series in locations where the temperature falls below -40 °C (-40 °F) or rises
above 150 °C (302 °F). Do not store the Model 1500 series in locations where the
temperature falls below -40 °C (-40 °F) or rises above 70 °C (158 °F). Avoid any
environmental condition that can result in internal condensation. Ensure that these
temperature and humidity requirements can also be met whenever the unit is shipped.
Store the lasers in the original container and packing material.

3.4.1 Claims and Repackaging

Immediately inform Lumentum and, if necessary, the carrier, if

• The contents of the shipment are incomplete

20

945-002 Rev503
 • The unit or any of its components are damaged or defective
• The unit does not pass the initial inspection

In the event of carrier responsibility, Lumentum will allow for the repair or
replacement of the unit while a claim against the carrier is being processed.

3.4.2 Returning Shipments to Lumentum

Lumentum only accepts returns for which an approved Return Material
Authorization (RMA) has been issued by Lumentum sales personnel. This
number must be obtained prior to shipping any material to Lumentum. The
owner’s name and address, the model number and full serial number of the unit,
the RMA number, and an itemized statement of claimed defects must be included
with the return material.

Ship return material in the original shipping container and packing material. If
these are not available, typical packaging guidelines are as follows:

1. Wear an anti-static wrist strap and work in an ESD controlled area.

2. Wrap the unit in anti-static packaging. Use anti-static connector covers, as

applicable.

3. Pack the unit in a reliable shipping container.

4. Use enough shock-absorbing material (10 to 15 cm or 4 to 6 in on all sides)

to cushion the unit and prevent it from moving inside the container. Pink poly
anti-static foam is the best material.

5. Seal the shipping container securely.

6. Clearly mark FRAGILE on its surface.

7. Always provide the model and serial number of the unit and, if necessary, the
RMA number on any accompanying documentation.

8. Ship the unit only to the address given at the beginning of this document.

21

945-002 Rev503
4 Operating and Maintenance Instructions
4.1 Laser Heads and Power Supply
Make sure the power supplies used match both the voltage and current requirements
of a laser head. Failure to do so will prevent the laser to function reliably or function
at all.

Warning

Power supplies are not interchangeable between models.

Connect the power supply only to the appropriate laser
model.

Warning
NEVER TOUCH A LASER CABLE WHEN ITS POWER
SUPPLY IS ON.
• A laser requires a high voltage start pulse of about 10,000 volts.
The normal operating voltage of a laser exceeds 1,000 volts and
can be as high as 4,000volts.
• A residual high voltage can exist on the cables leading from the
power supply to the laser after the power supply is turned OFF.
Wait at least 10 secs after turning it OFF before manipulating
them.

4.2 Initializing the Laser

Warning
• The power supply input cord plug must have a safety
ground contact, and this contact must be connected to the
power source receptacle safety ground contact.
Ensure this contact is grounded to the user’s facility.
• Failure to do so may expose the user to high
voltage if touches the laser housing or an accessory
connected to the laser housing.

22

945-002 Rev503
 Warning
• Ensure the power supply is in the OFF state.
• When using a power supply 1200 model ensure that the
key switch on the power supply is in the “OFF” position.
• Ensure the laser cable and power supply input cord are
properly connected to their sources,

BEFORE TURNING ON the laser power supply, perform the following steps:

1. Always have the laser connected to the power supply before applying power.

2. Check the voltage requirement of the power supply.

3. Lasers equipped with a laser shutter must have it in the “open” position.
The shutter is manually placed in the open or closed position.

TO INITIALIZE THE LASER:

1. Energize the power supply input, or turn the key switch of a 1200 power supply to
the “ON” position.

2. The 1200 power supply or a power supply equipped with FDA-CDRH delay will
ignite the laser after a three-second delay.

3. Emission from the laser head will be visible.

4.3 Troubleshooting

Warning
• A residual high voltage can exist on the cables leading from the
potted module to the high voltage receptacle after the power supply is
turned off.

If the laser fails to turn on after following the initialization procedure, perform the
following:

1. De-energize the power supply input, or turn the key switch of a 1200 power
supply to the “OFF” position.

2. Unplug the high voltage power cable.

23

945-002 Rev503
 3. Check the fuse in the power supply.

3.1 If the fuse is open, replace it with an identical fuse and follow the
initialization procedure again.
An abnormal input line transient could cause the fuse to trip. If this is the reason
for failure, normal operation can be resumed.

3.2 If the laser still fails to turn on or if the fuse continues to open, a malfunction
within the power supply may exist. Exchange the power supply and follow the
initialization procedure again.

4. If the lasers turns on with the replacement power supply, return the faulty power
supply to Lumentum in accordance with the return procedure outlined in the 3.4.2
Returning Shipments to Lumentum section.

5. If the laser output still is not present or is intermittent, ensure that the power
supply input voltage is within required limits and the high voltage connection
between the laser head and the power supply is properly mated.

6. If the problem persists, exchange the laser and follow the initialization procedure
again

7. If the laser output still is not present or is intermittent return both the power supply
and laser head to Lumentum in accordance with the return procedure outlined in
the 3.4.2 Returning Shipments to Lumentum section.

4.4 Calibrating the Unit

The laser units do not require calibration.
A laser will be able perform to specifications after the initial warm-up period is up.
Beam parameters are guaranteed at the Far Field.

Warning
• Do not dismantle the laser head for any reason.
The laser plasma tube and ballast resistance are sealed in the laser
head and any manipulation or shock may misalign the optics, affects
performance or decrease power, or prevent lasing.
• Access to Lumentum power supplies is not intended.
Contact a Lumentum representative for any issue regarding the laser
head or power supply.

24

945-002 Rev503
5 Power Supplies
All Lumentum helium-neon power supplies provide a highly regulated constant current
Output, allowing for excellent optical stability and performance.

The power supply automatically adjusts laser tube voltage to maintain a fixed discharge
current.

A CDRH time delay is active on all power supplies, and may be defeated on power supply
Modules or OEMs.

All power supplies have complete fault protection and can withstand output short circuits,
output open circuits, or arc-to-ground conditions.

Power supplies are available for 100, 115, 230 VAC, 24VDC and 12VDC operation, with
efficiencies greater than 85 percent.

Key Features
• Highly regulated, constant-current output
• Complete fault protection
• Exceptional direct current (DC) stability
• Typical conversion efficiency >85%
• Compact, rugged packaging
• Exceptional lifetime

Applications
• For use with Lumentum helium-neon laser heads and tubes

Compliance
• TÜV EN 60950
• CUL UL60950-1

Environmental
• Ambient Temperature: Operating -20ºC to 50 ºC
Non-operating -20ºC to 70 ºC
• Humidity: <95% non-condensing
• Altitude: Operating < 3,048 meters (10,000ft)
Non-operating < 12,192 meters (40,000ft)
• Reliability testing: Shock: 25 g for 11 msec
Vibration: random 1-200Hz, 1.15grm
Drop: ISTA 2

25

945-002 Rev503
 5.1 Model 1200 Series Power Supply

The Model 1200 power supply is energized by 100, 120 or 230VAC 50/60Hz source.

A hard wired power cord is built-in the power supply, the plugs are shown in Figures
8 and 9.
• For 230VAC units,
A 250VAC 10A 2.5 meter long cord terminated with CEE 7-VB plug

Figure 8. Model 1500 Series power supply 230VAC cord

• For 100VAC, 120VAC units:

A 125VAC 10A 72” long cord terminated with a NEMA 5-15P plug.

Figure 9. Model 1500 Series power supply 100 , 120 VAC cord

26

945-002 Rev503
 Warning
The Series 1200 has a front panel Safety Key switch and a rear panel
Safety Interlock jumper. Both are wired in series with the input AC
power line conductor.
Disconnect the power supply from the input power whenever the Safety
Interlock is wired to an external interrup loop.

The key switch is a Oslo K1-101-S1S2N2 KEY A126.

The interlock plug a MOLEX (BEAU VERNITRON) P-3302-CCT or 0383315602.

Models 120x-1 are used with 120VAC inputs, 120x-2 with 230VAC inputs, and
120x-3 with 100VAC inputs.

Table 8 lists the pairing between 1100s lasers and 1200s power supplies.

Power Supply Output Current Optical

Input Voltage
Model Laser Model Voltage DC +/- Noise
+/-10%
+/- 200V 0.1mA <10MHz

1201-1 115 VAC

102, 196,
1201 1201-2 230 VAC 1101/P, 1103/P
1700VDC 4.9mA <0.1%
1201-3 100 VAC
1202-1 115 VAC
1202 1202-2 230 VAC 1125/P, 1137/P 2300VDC 6.0mA <0.2%
1202-3 100 VAC
1205-1 115 VAC
1205 1205-2 230 VAC 1107/P, 1108/P 1250VDC 4.0mA <0.1%
1205-3 100 VAC
1206-1 115 VAC
1206 1206-2 230 VAC 1122/P 1800VDC 6.5mA <0.1%
1206-3 100 VAC
1216-1 115 VAC
1216 1216-2 230 VAC 1135/P 3100VDC 6.5mA <1%
1216-3 100 VAC
1218-1 115 VAC
1218 1218-2 230 VAC 1144/P, 1145/P 3800VDC 6.5mA < 0.5%
1218-3 100 VAC

Table 8: 1200s Model Selection for 1100 Laser Series.

27

945-002 Rev503
The Power Supply 1200 Series carry the CE mark.

Fig. 10- Small Model 1200 Series Power Supply Dimensions.

1201-xx, 1202-xx, 1205-xx, 1206-xx, 1207-xx, 1208-xx

Fig. 11- Large Model 1200 Series Power Supply Dimensions.

1216-xx, 1218-xx

28

945-002 Rev503
 5.2 OEM Series Power Supply

The OEM or Module power supplies allows to drive the lasers where confined spaces
are encountered.

Their output / input power efficiency is > 75%.

A typical current ripple is < 0.75% rms or <2%p-p.
They include a standard Interlock Loop input for safety interrupt when opened.

There are three types of Module Series: 101T, 314T and 380T.

101T
The 101T Series Module dimensions are 3.75”W x 1.50”D x 1.00”H.
The standard input is 12VDC. It provides four typical output voltage / current
versions. Its dimensions are shown in Figure 8.

The standard configuration carries:

• 12 inches input wires bundle (flying leads). Red-12VDC, Black-ground
• 12 inches output high voltage cable terminated in an Aldon type of HV
connector,
• Interlock Loop wire (purple color) to enable shutdown when a safety loop and
is open.
•
The table 9 show available 101T models. The Figure 12 shows the dimensions.
HV Output CURRENT Input HV cable Input cable
Lumentum PN Model name Special
(VDC) (mA) (VDC) (in) (in)
21105343 101T-1250 1250 4.0 12 12 12
22087812 101T-1250-4-5 1250 4.0 12 12 6 No Itlk, Molex input
21105344 101T1250-4-2 1250 4.0 12 6 12
21105346 101T-1250-4-4 TTL 1250 4.0 12 12 12 TTL input
21105348 101T-1350-4-1 1350 4.0 12 12 12
21172231 101T-1250-1350-3.5-BRH-2 1350 3.5 12 6 12 Start delay
21104786 101T-1700-4.5-TTL-1 1700 4.5 12 12 12 TTL input
21105351 101T-1700-4.9-2 1700 4.9 12 6 12
21127603 101T-1700-4.9-TTLBRH-4 1700 4.9 12 12 12 TTL input, Delay
21105422 101T-1700 1700 4.9 12 12 12
21105423 101T-1800 1800 6.5 12 12 12
21105424 101T-2300-6.0-4 2300 6.0 12 12 12
21158281 101T-2300-6.0-4-24 ADJ 2300 6.0 24 12 12

Table 9 - 101T Models.

29

945-002 Rev503
 Figure 12- Module 101T Series Power Supply Dimensions

314T
The 314T Series Module dimensions are 4.25”W x 3.00”D x 1.20”H.
Similar to the 101T, the 314T Series offer typical combination of voltage / current
outputs but using the AC power line as an input. Wiring guide shown in Appendix.
The standard input for the 314T Series is 120/230VC. Some Modules are available
for 100/200VAC inputs.
The standard configuration carries:
• 12 inches input wires bundle (flying leads),
• either a 12 or a 6 inches output high voltage cable terminated in an Aldon type
of HV connector,
• Interlock Loop wire to enable shutdown when a safety loop and is open.
Its dimensions are shown in Figure 13. Table 10 shows available 314T models.

HV Output CURRENT Input HV cable Input cable

Lumentum PN Model name
(VDC) (mA) (VAC) (in) (in)
21105428 314T-1250-4-4 1250 4.0 120/230 12 12
21105377 314T-1250 1250 4.0 100/200 12 12
21105378 314T-1250-4-2 1250 4.0 120/230 6 12
21105379 314T-1350-4-2 1350 4.0 100/200 6 12
21105380 314T-1700 1700 4.9 120/230 12 12
21105381 314T-1700 1700 4.9 100/200 12 12
21105382 314T1700-4.9-2 1700 4.9 120/230 6 12
21105383 314T-1700-4.9-2 DELAY 1700 4.9 120/230 6 12
21105385 314T-1800 1800 6.5 120/230 12 12
21105386 314T1800-6.5-2 1800 6.5 150/230 6 12
21105432 314T-2300 2300 6.0 100/200 12 12
21105430 314T-2300 2300 6.0 120/230 12 12

Table 10 - 314T Models.

30

945-002 Rev503
 Figure 13- Module 314T Series Power Supply Dimensions

380T
The 380T Series Module dimensions are is 7.00”W x 2.40”D x 1.40”H.

Similar to the 314T, the 380T Series offer typical combination of voltage / current
outputs with higher output voltage ranges.
The standard input for the 380T Series is 120/230VC. Some Modules are available
for 100/200VAC inputs. Wiring guide shown in Appendix.

The standard configuration carries:

• 12 inches input wires bundle (flying leads),
• either a 12 inches output high voltage cable terminated in an Aldon type of
HV connector,
• Interlock Loop wire to enable shutdown when a safety loop and is open.

Its dimensions are shown in Figure 14.

HV
Lumentum CURRENT Input HV cable Input cable
Model name Output
PN (mA) (VAC) (in) (in)
(VDC)
21105400 380T-3100 100V 3100 6.5 100/200 12 12
21105435 380T-3100 3100 6.5 120/230 12 12
21105403 380T-3800 100V 3800 6.5 100/200 12 12
21105436 380T-3800 3800 6.5 120/230 12 12

Table 11 - 380T Models

31

945-002 Rev503
 Figure 14- Module 380T Series Power Supply Dimensions

Table 12 lists the pairing between 1100s, 1000s lasers and standard OEMs power supplies.

Output Current Optical

Input Voltage
Power Supply Model Laser Model Voltage DC +/- Noise
+/-10% +/- 200V 0.1mA <10MHz
101T-1700 12VDC
102, 196, 1101/P, 1103/P
314T-1700 120/230VAC 1700VDC 4.9mA <0.1%
1007*, 1008 "
314T-1700 100V 100/200VAC
101T-2300-6.0-4 12VDC
314T-2300 120/230VAC 1125/P, 1137/P 2300VDC 6.0mA <0.2%
314T-2300 100V 100/200VAC
101T-1250 12VDC
101T-1350-4-1 12VDC
1107/P, 1108/P
101T-1250-1350-3.5-BRH-2 12VDC 1250-1350VDC 4.0mA <0.1%
1001", 1003 *, 098-3 *
314T-1250 100/200VAC
314T-1250-4-2 120/230VAC
101T-1800 12VDC
1122/P
314T-1800 120/230VAC 1800VDC 6.5mA <0.1%
1022*

380T-3100 100V 230 VAC 1135/P 3100VDC 6.5mA <1%

380T-3100 100V 100/200VAC

380T-3800 120/230VAC 1144/P, 1145/P 3800VDC 6.5mA < 0.5%

380T-3800 100V 100/200VAC
* Laser tubes require a series ballast resistor, otherwise can become unstable.
Table 12: OEMs Model Selection for 1100 and 1000 Laser Series.

32

945-002 Rev503
 Lumentum also offers a variety of OEM power supplies as shown below in Table 13.

HV Output CURRENT HV cable Input cable Size

Lumentum PN Model name Input (VDC) Comments
(VDC) (mA) (in) (in) LxDxH
21105356 103-1250 1250 4.0 12VDC 6 12 4 x 1.5 x 1
21105357 103-1700 1700 4.9 12VDC 6 12 4 x 1.5 x 1
21105427 106-05-4.0 1250 4.0 12VDC 6 12 4 x 1.5 x 1
21105364 111-1700-4.9-TTL-2 1700 4.9 24VDC 6 12 5.1 x 1.5 x 1.1 TTL input
21105367 121T-1250-4-2 1250 4.0 12VDC 6 12 5.1 x 1.5 x 1.1
21105374 180T-2700-5-4 2700 5.0 12VDC 12 12 4.3 x 3 x 1.2
21105376 314S-1250-4-1 1250 4.0 1020/230VAC 12 12 4.3 x 3.3 x 1.2

Table 13: Other OEM models.

33

945-002 Rev503
6 APPENDIX

6.1 1100 Lasers Housing Configuration

The Model 1100 Series laser head basic dimensions are shown in Figure 15. The
values are listed in Table 14. The shaded areas are free areas for user installation.

"L" max.

"X" "A" "B" "Y"

HIGH
VOLTAGE
CABLE

Plane of
Polarization
"D" dia. "E" Vector

Accessory Housing Holes M-3

on 1.38" (34.9 mm) bolt circle
(1.740" diameter head only)

Figure 15: Model 1100 Series Housing Configuration

Models “L” “D” “A” “B” “X” “Y”

1107,1107P 17.78 3.162 ± .013 cm 2.54 cm 2.54 cm 1.27 cm 1.9 cm
1108, 108P cm (1.245 ± .005 in) (1.0 in) (1.0 in) (.50 in) (.75 in)
(7.0 in)
1101, 1101P 24.13 3.162 ± .013 cm 5.08 cm 5.08 cm 2.54 cm 2.54 cm
1103, 1103P cm (1.245 ± .005 in) (2.0 in) (2.0 in) (1.0 in) (1.0 in)
(9.5 in)
1122, 1122P 27.2 cm 4.42 ± .013 cm 5.08 cm 5.08 cm 3.81 cm 3.81 cm
(10.71 (1.74 ± .005 in) (2.0 in) (2.0 in) (1.5 in) (1.5 in)
in)
1125, 1125P, 40.11 4.42 ± .013 cm 5.08 cm 5.08 cm 7.62cm 7.62cm
1137, 1137P, cm (1.74 ± .005 in) (2.0 in) (2.0 in) (3.0 in) (3.0 in)
(15.79
in)
1135, 1135P, 48.6 cm 4.42 ± .013 cm 5.08 cm 5.08 cm 10.16 cm 10.16 cm
(19.13 (1.74 ± .005 in) (2.0 in) (2.0 in) (4.0 in) (4.0 in)
in)
1144, 1144P, 63.5 cm 4.42 ± .013 cm 5.08 cm 5.08 cm 12.7 cm 12.7 cm
1145, 1145P (25.0 in) (1.74 ± .005 in) (2.0 in) (2.0 in) (5.0 in) (5.0 in)

Table 14: Model 1100 Series dimensions

34

945-002 Rev503
 6.2 OEMs AC WIRING GUIDANCE

The Table 15 shows the Input AC wiring for the 314T and 380T power supplies.

AC INPUT CONNECTIONS
WIRE COLOR 100VAC 200VAC WIRE COLOR 120VAC 230VAC
RED HOT HOT BROWN WHITE HOT HOT
RED NEUTRAL BLUE WHITE NEUTRAL
YELLOW NEUTRAL WHITE YELLOW NEUTRAL
GREEN GND GND GREEN/YELLOW GREEN GND GND

Table 15. OEM Power Supply AC INPUTS

35

945-002 Rev503
Contact Information

Telephone

APAC 800 0825-LITE (+800 0825-5483)

China 10 400 120-LITE (+10 400 120-5483)
EMEA 800 0000-LITE (+800 0000-5483)
North America 1 844 810-LITE (1 844 810-5483)

Fax

APAC 800 0010-LITE (+800 0010-5483)

China 10 400 121-5483
EMEA 800 0010-LITE (+800 0000-5483)
North America 1 844 910-5483

If you have issues using these toll-free numbers, please contact

[email protected] or call 1 613-843-5378
Internet: www.lumentum.com

Headquarters
Lumentum Operations LLC
400 N. McCarthy Blvd.
Milpitas, CA 95035
USA.

36

945-002 Rev503