BT1

User Manual V1.0

 Contents
1 Product overview........................................................................................................................................ 3
1.1 Product introduction............................................................................................................................ 3
1.2 Product Features.................................................................................................................................. 3
1.3 Technical parameters........................................................................................................................... 3
2 Installation, wiring and Debugging............................................................................................................ 3
2.1 Installation............................................................................................................................................3
2.2 Wiring.................................................................................................................................................. 4
2.3 Debug................................................................................................................................................... 4
3 Basic functions............................................................................................................................................4
3.1 Enter into administrator mode............................................................................................................. 5
3.2 Change the administrator password.....................................................................................................5
3.3 Add card user....................................................................................................................................... 5
3.3.1 Quickly to add card user............................................................................................................... 5
3.3.2 Specifying the ID number to add a card.......................................................................................5
3.3.3 Specifying the ID number to add a user password.......................................................................5
3.4 Deleting users.......................................................................................................................................6
3.4.1 Quickly delete the card................................................................................................................. 6
3.4.2 Specify ID Number to Delete Card or Password......................................................................... 6
3.4.3 Deleting all users.......................................................................................................................... 6
3.5 Setting the door opening method.........................................................................................................6
3.6 Setting the open time........................................................................................................................... 6
3.7 Setting the alarm time.......................................................................................................................... 6
3.8 Set the door contact..............................................................................................................................6
3.9 Setting the security mode.....................................................................................................................7
3.10 Exit from the administrator mode......................................................................................................7
3.11 Change user’s password.....................................................................................................................7
3.11.1 Change password by card........................................................................................................... 7
3.11.2 Change password by ID number.................................................................................................7
3.12 Users open the door........................................................................................................................... 7
3.13 Resetting To Factory Default Setting................................................................................................ 7
4 Administrator mode operation summary table........................................................................................... 8
5 Simple Troubleshooting..............................................................................................................................8
6 Mobile operating function.......................................................................................................................... 9
6.1 Download and install mobile APP.......................................................................................................9
6.2 Administrator's mobile operations.......................................................................................................9
6.3 Other users add device.......................................................................................................................12
6.4 Users open doors with mobile phones...............................................................................................12
6.5 Device upgrade.................................................................................................................................. 13
6.6 APP Common Questions................................................................................................................... 13
7 Packing list................................................................................................................................................14
 BT1 User Manual V1.0

1 Product overview
1.1 Product introduction
This product uses high-strength ABS plastic body, with proximity card (EM card, also known as ID card)
or password or mobile Bluetooth to open the door, built-in highly integrated microcontroller, simple
circuit, safe and reliable, economical and durable, suitable for office, villa etc.
1.2 Product Features
• Mobile Bluetooth opens the door and an administrator shares it with multiple users.
• 1000 user cards bound with 1000 user passwords, and the user can modify password by himself
• Opening door modes: card, card + password, card or password, password.
• Opening time: 50mS, 1-98 seconds for normal mode, 99 seconds for switch mode;
• It can connect with the door magnetic detection for alarm or door closing prompts;
• Built-in high current MOS tube, can directly drive external alarm;
• Safe mode can be set: 10 times of invalid card or password will automatically lock the machine
for 10 minutes;
• Can connect with an exit button, convenient to open the door from inside.
• Safety screw at the bottom to prevent malicious destroy.
1.3 Technical parameters
• Working voltage: DC 12V±2V
• Static current: up to 30mA
• Operating current: up to 100mA
• Contact current of relay: up to 1A
• Working temperature: -20 to 50℃
• Working humidity: 0 to 95%
• Maximum Card Reading Distance
• Product Size: 130mm Long X 75mm Wide X 17mm High

2 Installation, wiring and Debugging

2.1 Installation
Unscrew the anti-tamper screw on the bottom of the product with the special anti-tamper screwdriver,
remove the back case of the product, then according to the opening position of the back case, use the
impact drill to open the corresponding holes on the wall, make a hole with diameter larger than 8mm,
and two holes with diameter of 6mm, then insert two matching plastic expansion screws, and fix the
back case to the wall with four matching self-tapping screws. As shown below:

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 3
 BT1 User Manual V1.0

2.2 Wiring
According to the selected wiring diagram, connect the wire according to the wiring diagram one by one.
The rest unused wire should be wrapped by the electrical tape. Be careful not to short circuit, or the
power supply will be burned out, then insert the wires into the access control keypad 8P and 2P socket.
check every wire is correct, briefly turn on the power to see if the indicator LED light is normal, and the
buzzer will beep once, otherwise cut off the power supply immediately, Check the wires again. If
everything is correct, install the front case of the product on the bottom case on the wall, and fix with
disassembly-proof screw.

The corresponding relationship between product wiring color and function is shown in the following
table:
NO. Sign Colour Function
1 ALARM- Grey Negative pole of alarm
2 OPEN Yellow One end of the exit button
3 D_IN Brown One end of gate magnetic switch
4 +12V Red Positive pole of power supply
5 GND Black Negative pole of power supply
6 NO Blue NO of Relay
7 COM Purple COM of Relay
8 NC Orange NC of Relay
9 BELL Pink One end of doorbell button
10 BELL Pink One end of doorbell button

The wiring diagram of the product is as follows:

2.3 Debug
Turn on the power supply and test according to the instructions. The debugging will be completed until
the lock can be opened correctly by reading card, password and exit button.

3 Basic functions
Operating conventions：
• A long sound＂Di-＂indicates correct operation. Three short sounds＂Di Di Di＂indicate wrong
operation . The indicator light flash in green means operate correctly.
• ＂#＂indicate confirm completed, normally used behind pass word, ID number, or parameter.

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 4
 BT1 User Manual V1.0
• ＂*＂indicate cancel the current operation or return to the previous menu.
• The management menu is fixed to 1 digit from 0-6, cannot press key＂#＂after it. After entering
setting menu, the indicator light turns to orange.
• Under administrator mode, it will automatically exit to standby state if there is no operation
within 30 seconds.
• Under non- administrator mode, it will automatically exit to standby state if there is no operation
within 5 seconds.
Light and buzzer indication:
Operation status Light color Buzzer
Standby Red
PIN inputting Red flash
Read the card in Card & PIN mode Red flash
Enter into administrator mode Red flash
Enter menu setting status Orange
Successful operation Green A long sound
Unlock period Green
Press numeric key A short sound
Press * A long sound
Failed operation Three short sound
3.1 Enter into administrator mode
* 6 digits administrator password #
For example:
*888888#
Note: 888888 is the default factory administrator code. It fixed to 6 digits. Enter into the administrator
mode first before start the below operations.
3.2 Change the administrator password
0 new password # new password #
For example:
0999999#999999#
3.3 Add card user
Below 3 methods to add a card user, the ID number range is 0-999, the user password is fixed to 6 digits,
and it can be operated continuously. Press * to exit the add user menu.
3.3.1 Quickly to add card user
1, read card, … , *
For example, continuously add 3 cards:
1, read card, read card, read card *
3.3.2 Specifying the ID number to add a card
1, ID number #, read card, … , *
For example, continuously add 3 cards with ID number as 1,2,3:
11# read card 2# read card 3# read card *
3.3.3 Specifying the ID number to add a user password
1, ID number #, 6 digits user password #, ... , *
For example, consecutively set 3 passwords with ID numbers 4, 5, and 6:
14#444444#5#555555#6#666666#*

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 5
 BT1 User Manual V1.0

3.4 Deleting users

There are three ways to delete a user, where the ID number ranges from 0 to 999, every ID number
corresponds to a card or password, and the deletion ID number indicates that a card or a password is
deleted, and the operation can be continued. Press the * key to exit the delete user menu.
3.4.1 Quickly delete the card
2, read card, … , *
For example, delete 3 cards continuously:
2, read card, read card, read card, *
3.4.2 Specify ID Number to Delete Card or Password
2, ID number #, …, *
For example, continuously delete three users with ID numbers 1, 2, and 3:
2,1#2#3#*
3.4.3 Deleting all users
2, 0000#, *
For example:
20000#*
3.5 Setting the door opening method
3, 0# Open the door by card.
3, 1# Open the door by card and password.
3, 2# Default value, open the door by card or password.
3, 3# Open the door by password.
For Example, set the card and password to open the door:
31#
3.6 Setting the open time
4, 0# Default value, set the opening time to 50 milliseconds.
4, (1-98) # set the opening time to 1-98 seconds, the default value is 5 seconds.
4, 99# Set the machine to switch mode, that is, change the lock status every time once door opened.
For example, set the opening time to 5 seconds:
45#
Note: The 50 millisecond door opening time is suitable for the electric control lock. The switch mode is
suitable for the normally open or normally closed door.
3.7 Setting the alarm time
5, 0# Default , No alarm.
5, (1-3)# Alarm time is 1-3 minutes.
For example, set the alarm time to 1 minute:
51#
3.8 Set the door contact
6, 0# Default , door contact invalid.
6, 1# Door contact valid.
For example, set the safe mode in lock mode :
61#
There are two functions if connect with door contact by default:
1. The door left open in 10 seconds after opening, the built-in buzzer will ring. Close the door ,
swipe the valid card or input correct user PIN Code #, wait for more than 1 minutes will release alarm.

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 6
 BT1 User Manual V1.0
2. If the door was opened by force, or open the door after 120 seconds when normal unlock. The
outer connecting alarm and built-in buzzer will alarm simultaneously. swipe the valid card or input
correct user PIN Code #, wait for more than 1 minutes will release alarm.
3.9 Setting the security mode
7, 0# Default value, set to normal mode.
7, 1# Set to lock mode. When the invalid card, user password or administrator password is
continuously tried 10 times, the keypad will be automatically locked for 10 minutes.
7, 2#
Alarm mode. If there are continuously 10 invalid cards, 10 incorrect PIN number or administrator code
within 10 minutes, both the buzzer and alarm output will be operated. Swiping valid card, or input valid
PIN number, or wait for 1 minute will release the alarm output.
For example, set to lock mode:
71#
3.10 Exit from the administrator mode
In the administrator mode of operation, press the * key many times until the indicator light is always red,
that is, to exit the administrator mode of operation.
3.11 Change user’s password
3.11.1 Change password by card
*, Read user card, Old user password #, New password #, New password #
For example, Change user password by card:
* Read user card 1234#123456#123456#
Note: A initial password 1234 will be generated when adding a new card user. The initial password can’t
open the door, Just can be used to change the card user’s password. The new password should be in 6
digits.

3.11.2 Change password by ID number

*, ID number #, old password #, new password #, new password #
For example, Change user’s password by ID:
*1#123456#111111#111111#
Note: when changing password by ID number, the old user password can not be initial password 1234.
3.12 Users open the door
Read the card, or enter 6 digits user’s passwords, or press the Exit button
Note: No pressing # key after entering the password reduces frequency of using # key and greatly
improves the service life of # key. When opening the door, there will be a long sound of "beep" and the
indicator light will turn green during unlock. when the opening mode is card and password, the interval
between reading card and enter the password cannot exceed more than 5 seconds.
3.13 Resetting To Factory Default Setting
When administrator password is out of mind, or after user randomly adjust various parameters, you can
return to the normal situation by resetting to factory default setting. As following:
power off, press *and hold it, then power on, release it until hear two beeps, and master password
will revert to 888888,And the keypad parameters are reset to factory default setting, detail is in the
“administrator mode operation summary table”, the user’s card and password won’t be deleted.

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 7
 BT1 User Manual V1.0

4 Administrator mode operation summary table

Enter master operation mode: * ( 6 digits administrator ) #
Menu Parameters or operation steps Function Default
( new administrator password ) #，
0 Modify administrator password 888888
( new administrator password again )#
Read card, … ,* Quickly add user card
1 ( ID No. ) #, read card, … ,* Add user card with ID No.
( ID No. ) #, ( user pin ), … ,* Add user pin with ID No.
Read card, … ,* Quick delete card
2 ( ID No. ) #, … ,* Delete card or pin with ID No.
0000#, * Delete all the users
0# Entry by card
1# Entry by card with pin together
3 2
2# Entry by card or pin
3# Entry by only pin
0# Set open time to 50mS
4 ( 1-98 ) # Set open time to 1-98S 5
99# Set to switch mode
0# Set to no alarm
5 0
(1-3)# Set alarm time to 1-3 minutes
0# Set door contact invalid
6 0
1# Set door contact valid
0# Set to normal mode
7 1# Set to lock mode 0
2# Set alarm output

5 Simple Troubleshooting
Fault
Possible causes Solution
phenomenon
Unusual Change to qualified power supply,
Power voltage too low or too much interference.
indicator light cable or restoring power.
When the security mode is set to lock mode, the
No response number of consecutive card swipes or password Restart power or wait 10 minutes.
entries exceeds 10 times.
Setting Opening Time According
1. Incorrect opening time setting. to Different Electric Lock
Abnormal
Requirements
unlocking
Strictly follow the requirements of
2. Wiring error.
wiring.
Can’t enter 1. Make sure the light is always red before
Operate in the right way.
administrator pressing the * key.
mode 2. Forget administrator password. Restore factory settings.

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 8
 BT1 User Manual V1.0

1. The way to open the door may be set to

Set the right way to open the door.
Can’t enter by password.
card 2. Too much power interference or too low Replacement of high quality power
voltage. supply or wire.
1. The password needs to be pre-set.
Administrators set or users use the card to modify Setting or modifying user
Can’t enter by the original password 1234 to a new six-digit passwords.
pin password.
2. Password Input Error. Enter the correct password.
Digits key Opening mode may be set as card opening or card
Set the right way to open the door.
invalid and encryption code opening.

6 Mobile operating function

6.1 Download and install mobile APP
Click or scan the following QR code, and download and install the "Sebury BleAccess" mobile APP.

For ios For Android

6.2 Administrator's mobile operations
There can only be one administrator on this machine. Administrators must be added first, and then other
users can be added by administrators. Administrator is added as follows:
1. Turn off the power supply of the machine and then turn it on again. Follow-up operation will be
carried out within 10 minutes.
2. Open APP, the user instructions interface shown in Figure 1. After clicking on "Scan QR Code", a
scanning window appears as shown in Figure 2, aiming at the QR code of the device on the product
chassis. After a moment, the device interface shown in Figure 3 appears, that is, the addition is
successful.

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 9
 BT1 User Manual V1.0

Figure 1 Figure 2
3. Click on the device name at the top of Figure 3. A dialog box for modifying the device name appears
as shown in Figure 4. Enter a new device name. As shown in Figure 5, click OK, that is, the
modification is successful, as shown in Figure 6. When assign users, the device name in the user's
mobile phone displays the last modified name.

Figure 3 Figure 4 Figure 5 Figure 6

Administrators add users as follows:
1. Click on "User Management" in Figure 6 and enter the list of users as shown in Figure 7.
Administrators are automatically added and can not modify their names.
2. Click "Add User" to add a user bar, as shown in Figure 8.

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 10
 BT1 User Manual V1.0

Figure 7 Figure 8
3. Click the user bar to enter the user's QR code page as shown in Figure 9. After modifying the user's
name, click "Change user information", and the QR code information will be changed accordingly. After
the modification, the QR code in the figure contains all the information eventually assigned to the user
as shown in Figure 10.

Figure 9 Figure 10
Administrators delete users as follows:
Slide to the left of the user bar, a "delete" button appears, click "delete", appear "confirm delete", and
then click "confirm delete", the user is deleted from the list.

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 11
 BT1 User Manual V1.0

Figure 11 Figure 12
6.3 Other users add device
The administrator opens the APP and enters the page shown in Figure 10, showing the user's QR code.
The user opens the APP and enters the page shown in Figure 1. After clicking on the "Scan QR Code",
the scanner window shown in Figure 2 appears, aiming at the user's QR code on the administrator's
mobile phone. After a moment, the device interface shown in Figure 3 appears, that is, adding devices is
successful.
6.4 Users open doors with mobile phones
Administrators or users can use mobile phones to open the door in the same way. The operation is as
follows:
1. Open APP, if the device has been added, it will go to the device list page shown in Figure 13.
Press the small button on the left side of the list bar directly. The display screen will vibrate. After a
moment, the button will turn blue and show "Open", and then open the door. As shown in Figure 14, the
button will be restored to its original state in 1 second.

Figure 13 Figure 14
2. Figure 13, press the other parts of the device list button, then enter the device home page, other
users will not appear the "User Management" button, press the big button in the middle of the page, the
display screen will vibrate, wait a moment, the button will turn blue, and display "open", then open the

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 12
 BT1 User Manual V1.0
door, as shown in Figure 16, after 1 second, the button restored to its original state.

Figure 15 Figure 16
6.5 Device upgrade
When the product firmware has a new version, APP will appear a prompt icon. Click on the red dot label
icon shown in Figure 17, a dialog box shown in Figure 18 will appear, click "OK", and the firmware will
start to upgrade, waiting for the upgrade to complete, as shown in Figure 19-20.

Figure 17 Figure 18 Figure 19 Figure 20

6.6 APP Common Questions
1. The user's QR code has been obtained from the administrator. Why can't you open the door?
Bluetooth is not on or too far away from the device and the signal is too weak.
2. Need to suspend the use of a user, but do not want to delete the user, OK?
Just change the user's name, and when the original name is changed back, the user can open the door
again.
3. Administrators can not enter the management user status, what is the reason?
The administrator is not near the device, or does not turn on Bluetooth, because the management user
needs to operate online, and can only operate after connecting with the device.
4. Are there any security risks after the administrator leaves his post? Can he still opens the door?
Don't worry at all, you can set up a new administrator, and must be re-energized within 10 minutes to

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 13
 BT1 User Manual V1.0
operate, scan the QR code on the machine, after success, the original administrator automatically fails,
will not open the door again.
5. Replacement of mobile phones or administrators, reinstall APP, the original user is lost?
No, because the user information is stored in the device. After entering the management user mode, APP
will download the device data again, modify the user information or add new users. APP will always
synchronize with the device.
6. Can the same cell phone operate multiple devices?
Yes, there are many different devices in the list of devices. You can open different doors by operating
different buttons.

7 Packing list
Name Model Number Remarks

Access control BT1 1 pcs

Quick start guide BT1 1 pcs

8p connecting wire 150mm 1 pcs

2p connecting wire 150mm 1 pcs

Rubber Bungs Φ6mm 2 pcs For mounting and fixing

Self Tapping Screws Φ4mm×25mm 2 pcs For mounting and fixing

For disassembling and
Screw Driver L-star 1 pcs
assembling rear cover

Sebury Technology Co.,Ltd http://www.sebury.com.cn

Page 14