Sensor Lazer

L-GAGE® LTF Time of Flight Laser Distance
Sensor with IO-Link
Instruction Manual
Original Instructions
195393 Rev. D
7 March 2019
© Banner Engineering Corp. All rights reserved
195393
L-GAGE® LTF Time of Flight Laser Distance Sensor with IO-Link
Contents
1 Product Description .........................................................................................................................................................3
1.1 Models ............................................................................................................................................................................................ 3
1.2 Overview ......................................................................................................................................................................................... 3
1.2.1 Features and Indicators ............................................................................................................................................................4
1.2.2 Display ......................................................................................................................................................................................4
1.2.3 Buttons .................................................................................................................................................................................... 4
1.3 Laser Description and Safety Information ...................................................................................................................................... 5
2 Sensor Installation .......................................................................................................................................................... 6
2.1 Mount the Sensor ........................................................................................................................................................................... 6
2.2 Wiring Diagrams ..............................................................................................................................................................................6
3 Sensor Programming ......................................................................................................................................................7
3.1 Quick Menu .....................................................................................................................................................................................7
3.2 Sensor Menu (MENU) ...................................................................................................................................................................... 8
3.3 Remote Input .................................................................................................................................................................................. 8
3.4 Locking and Unlocking the Sensor ...............................................................................................................................................10
3.5 Discrete Output Menu ...................................................................................................................................................................10
3.5.1 Two-Point TEACH .................................................................................................................................................................. 11
3.5.2 Midpoint TEACH ....................................................................................................................................................................12
3.5.3 Adjust Switch Point One ....................................................................................................................................................... 14
3.5.4 Adjust Switch Point Two ....................................................................................................................................................... 15
3.5.5 TEACH Switch Point ..............................................................................................................................................................15
3.5.6 Adjust Switch Point ............................................................................................................................................................... 16
3.5.7 Mode ..................................................................................................................................................................................... 16
3.5.8 Switch Point Reference (SPtRef) ............................................................................................................................................17
3.5.9 Switch Point TEACH Offset ...................................................................................................................................................18
3.5.10 Switch Point Hysteresis .......................................................................................................................................................18
3.5.11 Timer .................................................................................................................................................................................... 19
3.5.12 Polarity ................................................................................................................................................................................. 19
3.6 Input Menu (INPUT) ....................................................................................................................................................................... 20
3.6.1 Input Type ............................................................................................................................................................................. 20
3.6.2 Input Active ........................................................................................................................................................................... 20
3.7 Measure Menu (MEASURE) ........................................................................................................................................................... 21
3.7.1 Speed .................................................................................................................................................................................... 21
3.8 Display Menu (DISPLAY) ................................................................................................................................................................22
3.8.1 Units ...................................................................................................................................................................................... 22
3.8.2 Zero and Shift ........................................................................................................................................................................22
3.8.3 View ....................................................................................................................................................................................... 23
3.8.4 Sleep ..................................................................................................................................................................................... 24
3.9 Information Menu (INFO) ................................................................................................................................................................24
3.10 Reset Menu (RESET) ....................................................................................................................................................................25
3.10.1 Factory Default Settings .......................................................................................................................................................25
4 Sync Master/Slave ........................................................................................................................................................26
5 Additional Remote TEACH Procedures ........................................................................................................................27
5.1 TEACH Both Discrete Output Switch Points Together .................................................................................................................27
5.2 TEACH Both Discrete Output Midpoints Together .......................................................................................................................28
6 Specifications ............................................................................................................................................................... 29
6.1 Repeatability Performance ............................................................................................................................................................ 30
6.2 Dimensions ................................................................................................................................................................................... 31
7 Troubleshooting ............................................................................................................................................................32
8 Sensor Menu Full Map ...................................................................................................................................................33
9 Accessories ................................................................................................................................................................... 34
9.1 Cordsets ........................................................................................................................................................................................ 34
9.2 Brackets ........................................................................................................................................................................................34
10 Banner Engineering Corp. Limited Warranty .............................................................................................................. 36
1 Product Description
Laser distance sensor with dual discrete (switched) outputs and IO-Link.
• High performance time of flight measurement

• Up to 24 m range
• Reliably detects challenging targets
• Fast set up with intuitive interface
WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury
or death. This device does not include the self-checking redundant circuitry necessary to allow its use in
personnel safety applications. A sensor failure or malfunction can cause either an energized or de-
energized sensor output condition.
1.1 Models
Laser Sensing
Family Range (m) Output Class Mode Connector
LTF 12 K C2 LD Q
12 = 12 m K = (2) NPN/PNP discrete C2 = Class 2 LD = Laser diffuse Blank = 2 m Integral Cable
24 = 24 m with I/O Link Q = Rotatable M12/Euro QD
QP = PVC M12/Euro Pigtail QD
W/30 = 9 m Integral Cable
QD models require mating cordset
1.2 Overview
The LTF Time of Flight Laser Distance Sensor with IO-Link is designed for precise, long-distance measurements. A 2-line
LCD shows the real-time distance measurement, in either millimeters or inches, when the sensor is in Run mode.
See Factory Defaults for a list of sensor default settings.
Models with current or voltage analog outputs are available.
www.bannerengineering.com - Tel: + 1 888 373 6767 3

1.2.1 Features and Indicators

Three LED indicators provide ongoing indication of the sensing
Discrete Output 1
LED Indicator status.
Power LED Display Power LED Indicator

Indicator Solid Green = Normal operation, power On and laser On
Discrete Output 2 Flashing Green (1 Hz) = Power On and laser Off (laser enable
LED Indicator mode)
Discrete Output LED Indicators
Solid Amber = Discrete Output is On
Push Buttons Off = Discrete Output is Off
Figure 1. Features
1.2.2 Display
The display is a 2-line, 8-character LCD. The main screen is
the Run mode screen, which shows the real-time distance
measurement.
Figure 2. Display shown in Run Mode
1.2.3 Buttons
Use the sensor buttons Down, Up, Enter, and Escape to program the sensor and to access sensor information.
Down and Up Buttons

Press Down and Up to:
• Access the Quick Menu from Run mode
• Navigate the menu systems
• Change programming settings
• Change individual digit values in distance based settings
When navigating the menu systems, the menu items loop.
Enter Button
Press Enter to:
• Access the Sensor Menu from Run mode
• Access the submenus
• Move right one digit in distance based settings
• Save changes
In the Sensor Menu, a check mark in the lower right corner of the display indicates that pressing Enter
accesses a submenu.
Press Enter to save changes. New values flash rapidly and the sensor returns to the parent menu.
4 www.bannerengineering.com - Tel: + 1 888 373 6767

Escape Button
Press Escape to:
• Leave the current menu and return to the parent menu
• Return to Run mode from the Quick Menu
Important: Pressing Escape discards any unsaved programming changes.
In the Sensor Menu, a return arrow in the upper left corner of the display indicates that pressing Escape
returns to the parent menu.
Press and hold Escape for 2 seconds to return to Run mode from any menu or remote teach.
1.3 Laser Description and Safety Information

CAUTION: Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure. Do not attempt to disassemble this sensor for repair.
A defective unit must be returned to the manufacturer.
1.3 Class 2 Laser Models
CAUTION: Never stare directly into the sensor lens. Laser light can damage your eyes. Avoid placing any
mirror-like object in the beam. Never use a mirror as a retroreflective target.
For Safe Laser Use - Class 2 Lasers

• Do not stare at the laser.
• Do not point the laser at a person’s eye.
• Mount open laser beam paths either above or below eye level, where practical.
• Terminate the beam emitted by the laser product at the end of its useful path.
Reference IEC 60825-1:2007, Section 8.2.
Class 2 Lasers
Class 2 lasers are lasers that emit visible radiation in the wavelength range from 400
nm to 700 nm, where eye protection is normally afforded by aversion responses,
including the blink reflex. This reaction may be expected to provide adequate
protection under reasonably foreseeable conditions of operation, including the use of
optical instruments for intrabeam viewing.
Class 2 Laser Safety Notes
Low-power lasers are, by definition, incapable of causing eye injury within the
duration of a blink (aversion response) of 0.25 seconds. They also must emit only
visible wavelengths (400 to 700 nm). Therefore, an ocular hazard may exist only if
individuals overcome their natural aversion to bright light and stare directly into the
laser beam.
Figure 3. FDA (CDRH) warning label (Class

2)

2 Sensor Installation
Note: Handle the sensor with care during installation and operation. Sensor windows soiled by
fingerprints, dust, water, oil, etc. may create stray light that may degrade the peak performance of the
sensor. Blow the window clear using filtered, compressed air, then clean as necessary using 70%
isopropyl alcohol and cotton swabs or water and a soft cloth.
2.1 Mount the Sensor

1. If a bracket is needed, mount the sensor onto the bracket.
2. Mount the sensor (or the sensor and the bracket) to the machine or equipment at the desired location. Do not
tighten the mounting screws at this time.
3. Check the sensor alignment.
4. Tighten the mounting screws to secure the sensor (or the sensor and the bracket) in the aligned position.
2.2 Wiring Diagrams

1
Key
+
2
3 12–30 V dc
1
–
PNP
NPN
3
or
4
Load D1_Out / IO-Link 4 5
2
Load D2_Out 1 = Brown
5 2 = White
Input
3 = Blue
shield 4 = Black
5 = Gray
* User-configurable PNP/NPN setting
Figure 4. IO-Link Models

3 Sensor Programming
Program the sensor using the buttons on the sensor or the remote input (limited programming options).
From Run mode, use the buttons to access the Quick Menu and the Sensor Menu. See Quick Menu on page 7 and
Sensor Menu (MENU) on page 8 for more information on the options available from each menu. For TEACH options,
follow the TEACH instructions.
In addition to programming the sensor, use the remote input to disable the buttons for security, preventing unauthorized or
accidental programming changes. See Remote Input on page 8 for more information.
from Run Mode
Access Access
Quick Menu Sensor Menu
See Quick Menu on page 7 See Sensor Menu (MENU) on page 8
Figure 5. Accessing the Menus
3.1 Quick Menu

The sensor includes a Quick Menu with easy access to view and change the discrete output switch points. Access the
Quick Menu by pressing Down or Up from Run mode. When in the Quick Menu, the current distance measurement
displays on the first line and the menu name and the discrete output switch points alternate on the second line of the
display. Press Enter to access the switch points. Press Down and Up to change each digit. Press Enter to move right
one digit. After reviewing each digit, press Enter again to save the new value and return to the Quick Menu. Press Cancel to
ignore any changes made if only some digits have been changed.
Quick Menu
access Sensor
Run Mode Menu (Top Menu)
D1 SPt1 (value)
set value with
D1 SPt2*(value) Save setting

and return to
Quick Menu
or
D2 SPt1 (value)
Cancel and
return to
Quick Menu
D2 SPt2*(value)
Spt2 not available unless in

Window Mode
Figure 6. Quick Menu Map (Window Mode)

3.2 Sensor Menu (MENU)

Access the Sensor Menu by pressing Enter from Run mode. The Sensor Menu is also accessible from the Quick Menu:
navigate to MENU and press Enter . The Sensor Menu includes several submenus that provide access to view and
change sensor settings and to view sensor information.
3.3 Remote Input

Use the remote input to program the sensor remotely. The remove input is disabled by default. Activate remote input using
the buttons to navigate to the Input Type menu option.
The remote input provides limited programming options and is Active Low by default. For Active Low, connect the gray
input wire to ground (0 V dc), with a remote switch connected between the wire and ground. To use the Active High
function, configure the sensor for Active High using the buttons on the sensor, then connect the gray input wire to V+ (12 to
30 V dc). Pulse the remote input according to the diagram and the instructions provided in this manual.
The length of the individual programming pulses is equal to the value T: 0.04 seconds ≤ T ≤ 0.8 seconds.
Exit remote programming modes by holding the remote input low for > 2 seconds, or waiting for the automatic 60-second
timeout, or by pressing and holding Escape for 2 seconds. The sensor returns to Run mode without saving any new
settings.

NOTE: Follow procedure for the TEACH/SET method

Run (highlighted in black box) chosen in the TEACH Selection menu.
Mode Timeout is 60 seconds.
Pulse Timing (T)
0.04 seconds < T < 0.8 seconds
Timing between Pulse groups > 1 second
1x Enter Remote TEACH RMT TCH with measurement value
1x Teaching..(D1SPt1) TchSPt1 (D1) with measurement value, then to TchSPt2 (D1)

Teaching..(D1SPt2) TchSPt2 (D1) with measurement value, then back to Run mode
REMOTE TEACH
1x
2x Teaching.. (D2SPt1) TchSPt1 (D2) with measurement value, then to TchSPt2 (D2)
1x Teaching..(D2SPt2) TchSPt2 (D2) with measurement value, then back to Run mode
3x Teaching.. (D1D2SPt1) TchSPt1 (D1 and D2) with measurement value, then to TchSPt2 (D1 & D2)
1x Teaching..(D1D2SPt2) TchSPt2 (D1 & D2) with measurement value, then
back to Run mode
4x Teaching.. (D1MdPt) TchMdPt (D1) with measurement value, then back to Run mode
(teaches SPt in Switch Mode)
5x Teaching.. (D2MdPt) TchMdPt (D2) with measurement value, then back to Run mode
(teaches SPt in Switch Mode)
6x Teaching.. (D1D2MdPt) TchMdPt (D1 & D2) with measurement value, then back to Run mode
(teaches Spt in Switch Mode)
2x Enter Remote Setup REMOTE SETUP
1x D1 Sensor Mode D1-Mode with current value
1x Set Mode to Alarm, then back to Run mode

2x Set Mode to Health, then back to Run mode
3x Set Mode to Switch , then back to Run mode
5x Set Mode to Window , then back to Run mode
REMOTE SETUP
2x D2 Sensor Mode D2-Mode with current value

1x Set Mode to Alarm, then back to Run mode
2x Set Mode to Health, then back to Run mode
3x Window Size WndSize with value

1x Set Window Size to X1, then back to Run mode
Refer to the Window size table for the acceptable values.
4x Sensor Lock / Unlock Locks or Unlocks Sensor
1x Unlock Sensor
2x Lock Sensor
8x Reset to Default Settings Resets Sensor to Factory Default Settings
Figure 7. Remote Input Map

Table 1: Remote TEACH Window Sizes
Remote TEACH Window Size (mm) Remote TEACH Window Size (mm)
Variable Variable
LTF12 LTF24 LTF12 LTF24
X1 10 10 X4 500 500
X2 20 20 X5 2000 2000
X3 100 100 X6 11950 23950
3.4 Locking and Unlocking the Sensor

Use the lock and unlock feature to prevent unauthorized or accidental programming changes. A lock symbol displays in
the upper left corner of the display to indicate when the sensor is locked. When locked, the menus are available to view
settings, but the values cannot be changed. The remote input is also disabled, except for the unlock function.
Button Instructions
To lock or unlock the sensor using the buttons, press and hold Down and Escape simultaneously for 3 seconds.
Remote Input Instructions

1. Access the setup mode.
Action Result
T T
Double-pulse the remote input. "REMOTE SETUP" displays.
T
2. Access the lock/unlock function.
Action Result
T T T T "LOCK" and the current status (unlocked or

Four-pulse the remote input.
T T T locked) display.
3. Lock or unlock the sensor.
Action Result
T "Unlocked" flashes and the sensor returns

Unlock : Single-pulse the remote line.
to Run mode. The sensor is unlocked.
"Locked" flashes and the sensor returns to

T T
Run mode. The sensor is locked and the
Lock: Double-pulse the remote input.
T lock symbol displays in the upper left
corner.
3.5 Discrete Output Menu

Use this menu to view or change
• Setpoints
• Midpoint
• Mode
• Timers
• Polarity

MENU D1_OUT D1_OUT Tch2Pt Tch2Pt TchSPt1 TchSPt1 50mm MENU D2_OUT D2_OUT Tch2Pt Tch2Pt TchSPt1 WndSize +00020mm
Tch2Pt TchSPt2 TchSPt2 12000mm Tch2Pt TchSPt2 TchMdPt 6000mm
D1_OUT TchMid TchMid WndSize WndSize +00020mm D2_OUT TchMid TchMid WndSize WndSize 20mm
TchMid TchMdPt TchMdPt 6000mm TchMid TchMdPt TchMdPt
Select Menu Item TchMid Offset Offset 0mm TchMid Offset Offset 0 mm
or
Press to Save Setting D1_OUT AdjSPt1 AdjSPt1 +00050mm D2_OUT AdjSPt1 AdjSPt1 +00050mm
D1_OUT AdjSPt2 AdjSPt2 +12000mm D2_OUT AdjSPt2 AdjSPt2 +12000mm
D1_OUT Mode Mode Alarm D2_OUT Mode Mode Alarm

Go Back to Parent Menu Mode Health Mode Health
or
Press and Hold to Go Back Mode Swtch Mode Swtch
to Run Mode Mode Swtch Mode Swtch
Mode Wnd Mode Wnd
Mode Wnd Mode Wnd
(in SPt mode only) D1_OUT SPtRef SPtRef Object Mode PFM
SPtRef Backgrnd (in SPt mode only) D2_OUT SPtRef SPtRef Object
SPtRef Custom SPtRef Backgrnd
(in SPtRef Custom D1_OUT Offset Offset 0 mm SPtRef Custom
mode only)
D1_OUT Hyst Hyst Auto (in SPtRef Custom D2_OUT Offset Offset 0 mm
mode only)
D2_OUT Hyst Hyst Auto
D1_OUT Timer Timer OffDly OffDly 0 ms
Timer Off1Sho Off1Sho 0 ms D2_OUT Timer Timer OffDly OffDly 0 ms
Timer OnDly OnDly 0 ms Timer Off1Sho Off1Sho 0 ms
Timer On1Sho On1Sho 0 ms Timer OnDly OnDly 0 ms
Polarity PNP Timer On1Sho On1Sho 0 ms

D1_OUT Polarity
Polarity NPN D2_OUT Polarity Polarity PNP
Polarity NPN
Default Setting
Figure 8. Discrete Output Menu Maps
3.5.1 Two-Point TEACH

The TchSpt1 and TchSPt2 options teach the desired switch points. When using the buttons, the switch points can be
taught independently. Both values must be taught when using the remote input. The same TEACH menus exist for both the
D1_OUT and D2_OUT, but the switch points are set independently.
Note: When in Switch mode, use TEACH Switch Point on page 15.
Navigate: MENU > Dx_OUT > Tch2Pt > TchSPt1 and navigate: MENU > Dx_OUT > Tch2Pt > TchSPt2
Remote Input: Available
Button Instructions
1. Present the target.
Action Result
The target's distance measurement value

Present the target. The target must be within the sensor's range..
displays.
2. Access the TEACH mode and TEACH the sensor.
Action Result
The selected TEACH mode and "Teaching"

display while the sensor is being taught.
TEACH Accepted
Navigate: MENU > Dx_OUT > Tch2Pt > TchSPt1
The new value is shown on the second line
OR of the display and flashes before it is saved
and the sensor returns to the parent menu.
Navigate: MENU > Dx_OUT > Tch2Pt > TchSPt2
TEACH Not Accepted
"FAIL" and a warning message display, and
the sensor returns to the parent menu.
3. Repeat steps 1 to 2 for the other switch point, if desired.


1. Access the TEACH mode.

Action Result
T "RMT TCH" and the current switch point

Single-pulse the remote input.
value displays.

Action Result
"RMT TCH" and the target's measurement

Present the switch point one target.
value display.
3. TEACH the sensor.

Action Result
"TchSPt1 Teaching" displays while the

sensor is being taught.
TEACH Accepted
T T The new value displays on the second line

Double-pulse the remote input. of the display, flashes, and the sensor goes
T to "TchSPt2" and the current measurement
value.
TEACH Not Accepted
"FAIL" flashes, the sensor returns to step 2,
and "RMT TCH" displays.

Action Result
"TchSPt2" and the target's measurement

Present the switch point two target.
value display.

Action Result
"TchSPt2 Teaching" displays while the

TEACH Accepted
T The new value displays on the second line
Single-pulse the remote input. of the display, flashes, and the sensor
returns to Run mode.
TEACH Not Accepted
3.5.2 Midpoint TEACH

The Midpoint TEACH uses both the window size and the
Output ON
TEACH midpoint to determine the actual measurement
window. For example, a window of 200 mm with a midpoint of
600 mm places the measurement window from 500 mm to
Output OFF 700 mm.
0 mm Midpoint 1000 mm
To use Midpoint TEACH:
(600 mm)
SP1 SP2 1. Set the window size.
(500 mm) (700 mm)
2. Set the measurement window using TEACH Midpoint
Figure 9. Window and Midpoint Example on page 13.

Window Size
The D_OUT > TchMid > WndSize option sets the window size that the Midpoint TEACH uses to set the setpoint one and
setpoint two thresholds.
The taught surface must be inside the defined sensing range, and at least one setpoint (with offset applied, if any) must be
located within the sensing range.
Parameters LTF12 LTF24
Window Size Minimum 10 mm 10 mm
Window Size Maximum 11950 mm 23950 mm
Range 50 mm to 12000 mm 50 mm to 24000 mm
Default Window Size 20 mm 20 mm

Method Action Result
"WndSize" and the current window

Push Button
size value display.
a. Double-pulse the remote input to enter T T a. "REMOTE SETUP" displays.

setup mode.
T b. "WndSize" and the current value
Remote Input b. Three-pulse the remote input to enter display.
window size mode. T T T
T T
2. Set the window size.
Method Action Result
a. "WndSize" and the new value

a. Use Down and Up to set the desired window size—the
display.
Push Button value changes in increments of 2.
b. The new value flashes and returns
b. Press Enter to save the new value. to "TchMid WndSize".
Pulse the remote input 1 to 6 times to select the desired window size.
Window Size
Pulses
LTF12 LTF24
1 10 mm 10 mm
Remote Input
(Sets A_OUT 2 20 mm 20 mm The new value flashes and the sensor
and D_OUT 3 100 mm 100 mm returns to Run mode.
window Size)
4 500 mm 500 mm
5 2000 mm 2000 mm
6 11950 mm 23950 mm
TEACH Midpoint
The TchMdPt option sets the midpoint that determines the actual measurement window.
Navigate: MENU > Dx_OUT > TchMid > TchMdPt
Button Instructions


Action Result

Present the target.
displays.
2. Access the TEACH midpoint mode and TEACH the sensor.

Action Result
"TchMdPt Teaching" displays while the

TEACH Accepted
of the display and flashes before it is saved
Navigate: MENU > Dx_OUT > TchMid > TchMdPt
and the sensor returns to "TchMid
TchMdPt".
TEACH Not Accepted
the sensor returns to "TchMid TchMdPt".

Action Result
T "RMT TCH" and the current measurement

value display.

Action Result

Present the target.
value display.

Action Result
"TchMdpt Teaching" displays while the

TEACH Accepted
T T T T
The new value displays on the second line
T
Five-pulse the remote input. of the display, flashes, and the sensor
T T T T returns to Run mode.
TEACH Not Accepted
"FAIL" and a warning message display, the
sensor returns to step 2, and "RMT TCH"
displays.
Window TEACH Offset

Use the D_OUT > TchMid > Offset menu to set an offset from the taught distance used during a Midpoint TEACH. By
default, the value is 0 mm because the window is centered around the taught distance. A positive offset value always shifts
the window towards the sensor.
3.5.3 Adjust Switch Point One

The AdjSPt1 option manually adjusts the value of the switch point one threshold for the Discrete Output when the sensor is
in Window mode. The value is adjustable within the sensor's range. It is required to be maintain the minimum window size
between switch points. This menu is not available when the sensor is in Switch, Alarm, or Health mode.

Remote Input: Not available

Default: 50 mm
3.5.4 Adjust Switch Point Two

The AdjSPt2 option manually adjusts the value of the switch point two threshold for the Discrete Output when the sensor is
in Window mode. The value is adjustable with the sensor's range. It is required to be maintain the minimum window size
between switch points. This menu is not available when the sensor is in Switch, Alarm, or Health mode.
Default: 12000 mm for LTF12; 24000 mm for LTF24
3.5.5 TEACH Switch Point

The TchSPt option teaches the distance at which the switch point threshold is placed when the Discrete Output is in Switch
mode. This menu is not available when the sensor is in Window, Alarm, or Health mode.
Navigate: MENU > Dx_OUT > TchSPt
Button Instructions
Action Result

Present the target. The target must be within the sensor's range.
displays.
2. Access the switch point TEACH mode and TEACH the sensor.
Action Result
"TchSPt Teaching" displays while the

TEACH Accepted
of the display and flashes before it is saved
Navigate: MENU > Dx_OUT > TchSPt
and the sensor returns to "Dx_OUT
TchSPt".
TEACH Not Accepted
the sensor returns to "Dx_OUT TchSPt".

1. Verify the sensor is in Switch mode.
Action Result

value display.
Action Result

Present the target.
value display.

Action Result
"TchSPt Teaching" displays while the

TEACH Accepted
T T T T T The new value displays on the second line
Five-pulse the remote input. of the display, flashes, and the sensor
T T T T
TEACH Not Accepted
3.5.6 Adjust Switch Point

The AdjSPt option manually adjusts the value of the switch point threshold for the discrete output when the sensor is in
Switch mode. The value is adjustable within the sensor's range. This menu is not available when the sensor is in Window,
Alarm, or Health mode.
Default: 50 mm
3.5.7 Mode
The Mode option sets the output to the desired mode.
Navigate: MENU > Dx_OUT > Mode
Default: Wnd mode
The following table describes the sensor modes.
Mode Description
Alarm Alarm Mode: The Discrete Output is Off while a target is detected by the sensor at any distance.
When a loss of signal occurs, the Discrete Output is On.
This mode has no associated thresholds.
Health Health Mode: The Discrete Output is On while a target is detected by the sensor at any distance.
When a loss of signal occurs, the Discrete Output is Off.
This mode has no associated thresholds.
Switch Switch Mode: The Discrete Output is On while a target is detected nearer than the switch point threshold.
When a target is detected farther than the switch point threshold or the signal is lost, the Discrete Output is Off.
Switch Switch Mode: The Discrete Output is Off while a target is detected nearer than the switch point threshold.
When a target is detected farther than the switch point threshold or the signal is lost, the Discrete Output is On.
Wnd Window Mode: The Discrete Output is On while a target is detected between the SPt1 and SPt2 thresholds. (Default)
When a target is detected outside the SPt1 and SPt2 thresholds or the signal is lost, the Discrete Output is Off.
Wnd Window Mode: The Discrete Output is Off while a target is detected between the SPt1 and SPt2 thresholds.
When a target is detected outside the SPt1 and SPt2 thresholds or the signal is lost, the Discrete Output is On.
PFM The discrete is pulsed at a frequency proportional to the sensor's measured distance.


Action Result
T T
Double-pulse the remote input. "REMOTE SETUP" displays.
T
2. View the current mode.
Action Result
T T
Double-pulse the remote input. The current mode displays.
T
3. Program the sensor.
Action Result
Pulse the remote input 1 to 6 times to select the desired mode.
Pulses Mode
T
1 Alarm
T T
2 Health
T
T T T
3 Swtch
T T The selected mode flashes and the sensor
T T T T
4 Swtch
T T T
T T T T T
5 Wnd
T T T T
T T T T T T
6 Wnd
T T T T T
3.5.8 Switch Point Reference (SPtRef)

The SPtRef menu only displays for a discrete output when it is set to switch mode. This setting cannot be changed with
remote teach.
• Object (default). Object mode automatically optimizes the switching threshold just past the taught distance, farther
away from the sensor's face.
• Background. Background mode automatically optimizes the switching threshold just in front of the taught distance,
closer to the sensor's face.
• Custom. Custom mode allows the user to define the location of the switching threshold relative to a taught distance
using the Offset menu that appears only after selecting Custom Switch Point Reference.
In Object or Background, the distance between the taught surface and the switching threshold varies depending on
measurement stability. Use object mode when teaching an object if a change in state is required when the object is no
longer present. Use background mode when teaching background so that the output state changes when a new object is in
front of the background.
Navigate: MENU > D_OUT > SPtRef
Default: Object

3.5.9 Switch Point TEACH Offset

Use this menu to set an offset from the taught distance after a switch point TEACH, if SPtRef is set to Custom.
By default, the value is 0 mm. A positive offset value always shifts the threshold towards the sensor.
Navigate: MENU > Dx_OUT > TchMd > Offset
Default: 0 mm
3.5.10 Switch Point Hysteresis

With the default setting of AUTO, the hysteresis value applied at each threshold is automatically calculated and set based
on target, distance and measurement repeatability, with a 10 mm minimum setting.
By default, the hysteresis is applied away from the sensor. Changing the SPt Ref setting from Object to Background
changes the direction of the hysteresis.
Mode
Swtch Swtch
Output Output
(On/Off) (On/Off)
Setpoint Reference
Object On On
(Object) Off Off
(SPtRef)
Hyst Hyst
Hyst Hyst
Background On On
(Backgrnd) Off Off
Near SPt Far Near SPt Far
Figure 10. How hysteresis affects the sensor output based on the discrete output switchpoint mode and the setpoint reference mode
Mode
Wnd Wnd
Output Output
(On/Off) Hyst Hyst (On/Off)
On On
Off Off
Hyst Hyst
Near SPt1 SPt2 Far Near SPt1 SPt2 Far
Figure 11. How hysteresis affects the two discrete output window modes

Mode = Swtch
Setpoint Mode Example:
SPtRef = Backgrnd
Far
Setpoint
Hysteresis
Near
Signal
On
Output
Off
Figure 12. How hysteresis affects the output on/off points when if the sensor is configured with mode = Swtch_|- and SPtRef configured as Backgrnd
Press the up button ( ) to manually select a constant hysteresis value between 2 mm and 12000 mm.
Navigate: MENU > D_OUT > Hyst
Default: Auto
3.5.11 Timer
The Timer option sets the delays and timers. ON
On/Off Delays and On/Off One-Shot timers can Output
be programmed between 1 to 9999 ms (a value OFF
of 0 disables the delay/timer). Figure 13 on page
19 defines how the delays/timers affect the
D D
output behavior. OFF Delay
Navigate: MENU > Dx_OUT > Timer

D D
Remote Input: not available OFF 1-Shot
Default: 0 ms for all timers

ON Delay D D
ON 1-Shot D D
Time (D = 1 - 9999 ms)

Figure 13. Delays/Timers
Some combinations of delays/timers are not allowed. The programming menu automatically disables invalid combinations
of delays/timers. The following table shows the allowable combinations of delays/timers.
Off Delay Off One-Shot Timer On Delay On One-Shot Timer
Off Delay (OffDly) OK OK OK N/A
Off One-Shot Timer (Off1Sho) OK OK N/A N/A
On Delay (OnDly) OK N/A OK OK
On One-Shot Timer (On1Sho) N/A N/A OK OK
3.5.12 Polarity
The Polarity option sets the discrete output polarity to either PNP (current sourcing) or NPN (current sinking). The physical
wiring of the sensor and the sensor polarity setting must match.

Default: PNP
3.6 Input Menu (INPUT)

Use this menu to view or change the:
• Multi-function input type
MENU INPUT INPUT Type Type Teach
Type LasrEnbl
Type SyncMstr
Type SyncSlve
Select Menu Item Type Disabled
or
Press to Save Setting
Go Back to Parent Menu

or
Press and Hold to Go Back
to Run Mode Default Setting
Figure 14. Input Menu Map
3.6.1 Input Type

The Type option sets the input type.
Navigate: MENU > INPUT > Type
Default: Disabled
Input Type Description
Teach The remote input is used to TEACH and program the sensor. (Default)
LasrEnbl The remote input is used to control when the laser emitter is On/Off.
SyncMstr The remote input is used as the Master Sync output to an attached Slave sensor (see Sync Master/Slave
on page 26).
SyncSlve The remote input is used as the Slave Sync input from an attached Master sensor (see Sync Master/
Slave on page 26).
Disabled The remote input is disabled.
3.6.2 Input Active

The Active option sets the active state of the remote input. Use the Active options to change the active input to Low or
High.
Navigate: MENU > INPUT > Active
Default: Low
Input Active Description

Low The remote input detects low (0 V) inputs and high-to-low transitions. (Default)

Input Active Description

High The remote input detects high (V+) inputs and low-to-high transitions.
3.7 Measure Menu (MEASURE)

Use this menu to view or change the:
• Speed
MENU MEASURE MEASURE Speed Speed Fast
Speed Standard
Speed Medium
Speed Slow
Select Menu Item
or

or
to Run Mode Default Setting
Figure 15. Measure Menu Map
3.7.1 Speed
The Speed option sets the speed at which the measurement is calculated. This process uses averaging in the digital
processing of the signal to calculate the measurement. A slower speed increases the response time of the sensor but
improves the repeatability. Refer to the repeatability specifications for each speed.
Navigate: MENU > MEASURE > Speed

Default: Medium
Speed Response Time * Lateral Entry
Fast 1.5 ms 5.5 ms
Standard 8 ms 16 ms
Medium 32 ms 48 ms
Slow 256 ms 288 ms
Figure 16. Lateral Entry Example

* Response time triples when using Master/Slave mode.

3.8 Display Menu (DISPLAY)

Use this menu to view or change
the:
• Display units MENU DISPLAY DISPLAY Units Units mm
• Display orientation Units in

• Sleep mode settings DISPLAY Zero Zero Near
Zero Far
Select Menu Item
or
DISPLAY Shift Shift Off
Shift SetZero
Shift AutoSet
or
DISPLAY View View Normal
to Run Mode View Invert
DISPLAY Sleep Sleep Disabled

Sleep 1min
Sleep 5min
Sleep 15min
Sleep 60min
Figure 17. Display Menu Map
3.8.1 Units
The Units option sets the displayed units to millimeters (mm) or inches (").
Navigate: MENU > DISPLAY > Units
Default: mm
3.8.2 Zero and Shift

Use the Display Zero menu to select the zero reference location. The default is , 0 = the face of the sensor.
• Near—0 = the face of the sensor; the measurement increases further from the sensor
• Far—0 = maximum range; the measurement increases closer to the sensor
Use the Display Shift menu to select whether the sensor shifts the zero reference location based on the last TEACH
process. The default is Off (0).
• Off—0 = the face of the sensor or the maximum range, depending on the zero setting
• SetZero—Sets the current distance as its new zero reference location. This process is independent of teaching
analog or discrete set points.
• AutoSet—Shifts the zero reference location at the taught distance during any analog or discrete setting teach.
This figure illustrates three examples of how changes to the zero and shift settings affect what distance readout is shown on
the display when in 2-pt TEACH mode. Changes to the zero setting affect the direction in which the distance increases.
Turning the shift setting on sets the taught location as the reference point for any distance measurement.

0 Display Reference 0 Display Reference
6000
4000 4000
Zero = Near 8000
Shift = Off
10 V
(Default Setting)
2000 mm
8000 8000
0V
12000 12000
mm mm
12000 12000
8000 8000
Zero = Far
Shift = Off 10 V
4000
2000 mm
4000
0V
6000
4000
0 0
Display Reference Display Reference
mm mm
8000 8000
4000 4000
Zero = Far
Shift = TchZero 10 V
(On) 2000 2000 mm
0 0 0
0V 0V
Display Reference Display Reference
-4000 -4000
mm mm
Figure 18. Example Zero and Shift settings
3.8.3 View
The View option sets the display orientation of the sensor. For applications where the sensor must be mounted so that the
display is not right-reading, invert the display for readability. The Down and Up buttons do not change when the display is
inverted.
Navigate: MENU > DISPLAY > View

Default: Normal
Figure 19. Normal Display Orientation Figure 20. Inverted Display Orientation
3.8.4 Sleep
The Sleep option sets when the display is put to sleep. Four timing options are available: 1, 5, 15, or 60 minutes. Sleep
mode is disabled by default. Sleep occurs in Run mode and any menu. To wake the sensor and return to the last viewed
mode or menu, press any button.
Navigate: MENU > DISPLAY > Sleep
Default: Disabled
3.9 Information Menu (INFO)

Use this menu to view model, part number (P/N), serial number (S/N), and firmware version (Version) information. Select one
of these options to view specific information for your sensor. This information is read-only.
Navigate: MENU > INFO

MENU INFO INFO Model Model LTF12K
INFO P/N P/N 801130
INFO S/N S/N F..S..P..D..
Select Menu Item INFO Version Version 1.0.0
or

or
to Run Mode
Figure 21. Information Menu Map

3.10 Reset Menu (RESET)

Use this menu to restore the sensor to the factory default
settings.
Navigate: MENU > RESET. Select Yes to apply the factory
defaults; select No to return to the Reset option without
MENU RESET RESET No
changing any sensor settings. RESET Yes
Remote Input: Eight-pulse the remote input

T T T T T T T T Select Menu Item
or
T T T T T T T

or
to Run Mode
Figure 22. Reset Menu Map
3.10.1 Factory Default Settings

Discrete Output LTF12 LTF24 Input Settings Value
Settings
Input Active Low
Adjust Switch Point 50 mm 50 mm
One Input Type Disabled
Adjust Switch Point 12000 mm 24000 mm

Two
Measure Settings Value
Mode Wnd Wnd
Speed Medium
Hyst Auto Auto
Polarity PNP PNP

Display Settings Value
Timer 0 ms for all timers 0 ms for all timers
Sleep Disabled
Window Size 20 mm 20 mm
Units mm
Zero Near
Shift Off
View Normal

4 Sync Master/Slave
Two LTF sensors may be used together in a single sensing application. To eliminate crosstalk between the two sensors,
configure one sensor to be the master and one to be the slave. In this mode, the sensors alternate taking measurements
and the response speed triples.
1. Configure the first sensor as the master; navigate: MENU > INPUT > Type > SyncMstr.
2. Configure the second sensor as the slave; navigate: MENU > INPUT > Type > SyncSlve.
3. Connect the gray (input) wires of the two sensors together.

5 Additional Remote TEACH Procedures

5.1 TEACH Both Discrete Output Switch Points Together
Use the following procedure to teach both Discrete Output switch points at the same time using the remote input. This
feature is not available using the buttons.
Action Result

value display.
Action Result
"RMT TCH"and the target's measurement

Present the switch point one target.
value display.
Action Result
"D1D2Spt1 Teaching" displays while the

TEACH Accepted
T T T The new value displays on the second line

Three-pulse the remote input. of the display, flashes, and then
T T "D1D2Spt2" and the current measurement
value display.
TEACH Not Accepted
Action Result
"D1D2Spt2" and the target's measurement

Present the switch point two target.
value display.
Action Result
"D1D2Spt2 Teaching" displays while the

TEACH Accepted
T The new value displays on the second line
Single-pulse the remote input. of the display, flashes, and the sensor
TEACH Not Accepted

5.2 TEACH Both Discrete Output Midpoints Together

Use the following procedure to teach an identical discrete output midpoint (switch point) for both D1_OUT and D2_OUT at
the same time using the remote input. This feature is not available using the buttons. Note that if the window sizes and/or
offsets were set independently (using the buttons), the windows taught using the following procedure could be different.
When the Discrete Output is set to Switch Mode, the SPt TEACH is executed with SPtRef=Custom and Offset=0 mm.
Action Result

value display.
Action Result
"RMT TCH"and the target's measurement

Present the midpoint (switch point) target.
value display.
Action Result
"D1D2MdPt Teaching" displays while the

TEACH Accepted
T T T T T T The new value displays on the second line
Six-pulse the remote input. of the display, flashes, and the sensor
T T T T T returns to Run mode.
TEACH Not Accepted

6 Specifications
Supply Voltage Sensing Beam
12 to 30 V dc Visible red, 660 nm
Power and Current Consumption (Exclusive of Load) Sensing Range -- LTF12
Normal Run Mode: < 2.1 W 90% White Target: 50 mm to 12000 mm
Current consumption < 85 mA at 24 V dc 18% Gray Target: 50 mm to 11000 mm
6% Black Target: 50 mm to 7000 mm
Supply Protection Circuitry
Protected against reverse polarity and transient overvoltages Sensing Range -- LTF24
90% White Target: 50 mm to 24000 mm
Construction
18% Gray Target: 50 mm to 18000 mm
Die-cast zinc housing; acrylic window 6% Black Target: 50 mm to 11000 mm
Maximum Torque Ambient Light Immunity
2.6 N·m (23.0 in-lbs) > 40000 lux
Output Configuration Delay at Power Up

User configurable to dual discrete NPN or dual discrete PNP; the 2 seconds
NPN/PNP polarity menus change both outputs
Measurement Output Rate
Output Ratings 0.5 ms
Discrete Output: 100 mA maximum (protected against continuous
overload and short circuit) Minimum Window Size
OFF-state leakage current (PNP): < 10 μA at 30 V 10 mm
OFF-state leakage current (NPN): < 200 μA at 30 V Boresighting
Output saturation voltage (PNP outputs): < 3 V at 100 mA
Output saturation voltage (NPN outputs): < 1.6 V at 100 mA 40 mm radius at 12000 mm
80 mm radius at 24000 mm
Remote Input
Temperature Effect
Allowable Input Voltage Range: 0 to Vcc
Active Low (internal weak pullup—sinking current): 50 mm to 12000 mm: ±0.25 mm/°C (typical)
>12000 mm: ±0.5 mm/°C (typical)
High State > 4.3 V at 740 μA maximum
Low State < 1.3 V at 800 μA maximum Linearity/Accuracy
Active High (internal weak pulldown—sourcing current): Reflectance LTF12 LTF24

High State > 4.3 V at 1.7 mA maximum
±10 mm ±20 mm ±25 mm ±50 mm ±100 mm
Low State < 1.3 V at 1.6 mA maximum
6% Black Card 5m 7m 7m 9m 11 m
Response Time
Fast: 1.5 ms 18% Gray Card 8m 11 m 11 m 14 m 18 m
Standard: 8 ms
Medium: 32 ms 90% White 12 m - 24 m - -
Slow: 256 ms Card
IO-Link Interface
Supports Smart Sensor Profile: Yes
Baud Rate: 38400 bps Resolution
Process Data Widths: 32 bits
LTF12: < 0.3 mm to 3 mm
IODD files: Provides all programming options of the display, plus
additional functionality. See p/n 199517 for IO-Link reference LTF24: < 0.3 mm to 4 mm
information. Resolution measured as twice repeatability with white target at slow
response speed at 20 °C. See repeatability curves for more detail.
Repeatability
Beam Spot Size
See Performance Curves
6.5 mm at 50 mm
10 mm at 7500 mm
12.5 mm at 12000 mm
35 mm at 24000 mm
Beam spot size is calculated as 1.6 times the D4σ measured diameter

Storage Conditions Required Overcurrent Protection

–30 °C to +65 °C (–22 °F to +149 °F)
Operating Conditions WARNING: Electrical connections must be
–20 °C to +55 °C (–4 °F to +131°F) made by qualified personnel in accordance
90% at +55 °C maximum relative humidity (non-condensing) with local and national electrical codes and
regulations.
Environmental Rating
IEC IP67; NEMA 6 Overcurrent protection is required to be provided by end product
application per the supplied table.
Shock
Overcurrent protection may be provided with external fusing or via
MIL-STD-202G, Method 213B, Condition I (100G 6x along X, Y and Z Current Limiting, Class 2 Power Supply.
axes, 18 shocks), with device operating Supply wiring leads < 24 AWG shall not be spliced.
Vibration For additional product support, go to www.bannerengineering.com.
MIL-STD-202G, Method 201A (Vibration: 10 Hz to 60 Hz, 0.06 inch (1.52
mm) double amplitude, 2 hours each along X, Y and Z axes), with Supply Wiring (AWG) Required Overcurrent Protection (Amps)
device operating
20 5.0
Application Note
22 3.0
For optimum performance, allow 15 minutes for the sensor to warm up
Certifications 24 2.0
26 1.0
Industrial
Control
Equipment 28 0.8
3TJJ
30 0.5
6.1 Repeatability Performance

LTF12 Models
14 (0.55) 6% Black Card 14 (0.55)

18% Gray Card
90% White Card Beyond Specified Range
12 (0.47) 12 (0.47)
1σ Repeatability in mm (inch)
Beyond Specified Range 6% Black Card

18% Gray Card
90% White Card
10 (0.39) 10 (0.39)
8 (0.31) 8 (0.31)
6 (0.24) 6 (0.24)
4 (0.16) 4 (0.16)
2 (0.08) 2 (0.08)
00 2 4 6 8 10 12 00 2 4 6 8 10 12
(6.6) (13.12) (19.7) (26.2) (32.8) (39.4) (6.6) (13.12) (19.7) (26.2) (32.8) (39.4)
Distance in m (ft) Distance in m (ft)
Figure 23. Speed: Slow (256 ms) Figure 24. Speed: Medium (32 ms)
14 (0.55) 14 (0.55)
6% Black Card 6% Black Card
18% Gray Card 18% Gray Card
12 (0.47) 90% White Card 90% White Card
12 (0.47)
10 (0.39) 10 (0.39)
8 (0.31) 8 (0.31)
6 (0.24) 6 (0.24)
4 (0.16) 4 (0.16)
2 (0.08) 2 (0.08)
0 00
0 2 4 6 8 10 12 2 4 6 8 10 12
(6.6) (13.12) (19.7) (26.2) (32.8) (39.4) (6.6) (13.12) (19.7) (26.2) (32.8) (39.4)
Figure 25. Speed: Standard (8 ms) Figure 26. Speed: Fast (1.5 ms)

LTF24 Models
20 (0.79) 20 (0.79)
1σ Repeatability in mm (inches)
18 (0.71) 18% Gray Card 18 (0.71) 18% Gray Card
90% White Card 90% White Card
16 (0.63) 16 (0.63)
14 (0.55) 14 (0.55)
12 (0.47) 12 (0.47)
10 (0.39) 10 (0.39)
8 (0.31) 8 (0.31)
6 (0.24) 6 (0.24)
4 (0.16) 4 (0.16)
2 (0.08) 2 (0.08)
0 0
0 4 8 12 16 20 24 0 4 8 12 16 20 24
(13.12) (26.24) (39.36) (52.48) (65.60) (78.72) (13.12) (26.24) (39.36) (52.48) (65.60) (78.72)

Figure 27. Speed: Slow (256 ms) Figure 28. Speed: Medium (32 ms)
20 (0.79) 20 (0.79)
18 (0.71) 18% Gray Card 18 (0.71) 18% Gray Card
90% White Card 90% White Card
16 (0.63) 16 (0.63)
14 (0.55) 14 (0.55)
12 (0.47) 12 (0.47)
10 (0.39) 10 (0.39)
8 (0.31) 8 (0.31)
6 (0.24) 6 (0.24)
4 (0.16) 4 (0.16)
2 (0.08) 2 (0.08)
0 0
0 4 8 12 16 20 24 0 4 8 12 16 20 24
(13.12) (26.24) (39.36) (52.48) (65.60) (78.72) (13.12) (26.24) (39.36) (52.48) (65.60) (78.72)

Figure 29. Speed: Standard (8 ms) Figure 30. Speed: Fast (1.5 ms)
6.2 Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.

7 Troubleshooting
Message/Indicator Description Resolution
Fail/ The TEACH failed, the target is out of range. The target TEACH the target within the measurement range.
Out might have moved out of range after the TEACH
of Range process began.
Fail/ The TEACH failed. The target is in range but the offset Adjust the offset value or target distance to keep the setpoint(s)
OfSt Out value caused the setpoint(s) to be out of range. within the measurement range.
of Range
MIN Wnd The adjusted or taught window size is too small; the The sensor automatically adjusts the window size to maintain
xx mm (xx in) minimum window size is displayed. the minimum window size and completes the adjust or TEACH
operation.
xxxx The threshold (xxxx) is less than the minimum sensing The desired window size is maintained, but the usable portion
< NEAR range. xxxx could be 4mA Pt (0V Pt), 20mA Pt (10V Pt) of the window is restricted to be within the defined sensing
or SPt1. range.
xxxx The threshold (xxxx) is greater than the maximum The desired window size is maintained, but the usable portion
> FAR sensing range. xxxx could be 4mA Pt (0V Pt), 20mA Pt of the window is restricted to be within the defined sensing
(10V Pt) or SPt2. range.
OutRnge The target is out of range, too dark, or the sensor is not Move the target within the measurement range.
measuring.
< NEAR During RUN mode the target is detected, but is inside The sensor can reliably detect targets up to the face of the
the NEAR measuring range. sensor, and the Discrete Output state is valid. The Analog
Output cannot be used to measure distances inside the NEAR
measuring range.
Power LED is flashing green The sensor input is set to laser enable and the input is See Input Type on page 20.
not active.
All LEDs are flashing The laser shuts off, the Power LED flashes green, the Contact Banner Engineering to resolve.
Output LEDs flash amber at 1 Hz, and the display is
blank.
The sensor has experienced a fault.
Type The slave mode sensor does not see the master's Make sure that the master mode sensor is configured and
Sync Slave pulse. functioning properly. Check the input wire connection between
the master and slave.

8 Sensor Menu Full Map

Top Menu Sub Menus
Enter
Run
Mode MENU D1_OUT D1_OUT Tch2Pt Tch2Pt TchSPt1 TchSPt1 50mm
Top Menu Tch2Pt TchSPt2 TchSPt2 12000mm
D1_OUT TchMid TchMid WndSize WndSize +00020mm

TchMid TchMdPt TchMdPt 6000mm
TchMid Offset Offset 0mm
D1_OUT AdjSPt1 AdjSPt1 +00050mm

Enter Quick Menu Loop
(see Quick Menu diagram) D1_OUT AdjSPt2 AdjSPt2 +12000mm
D1_OUT Mode Mode Alarm

Mode Health
Mode Swtch
Mode Swtch
Select Menu Item Mode Wnd
or Mode Wnd
(in SPt mode only) D1_OUT SPtRef SPtRef Object
SPtRef Backgrnd
SPtRef Custom
Go Back to Parent Menu (in SPtRef Custom
Offset 0 mm
or D1_OUT Offset
mode only)
to Run Mode
Top Menu Sub Menus
D1_OUT Timer Timer OffDly OffDly 0 ms
Timer Off1Sho Off1Sho 0 ms
Timer OnDly OnDly 0 ms MENU INPUT INPUT Type Type Teach
Type LasrEnbl
Timer On1Sho On1Sho 0 ms
Type SyncMstr
D1_OUT Polarity Polarity PNP
Type SyncSlve
Polarity NPN
Type Disabled
INPUT Active Active Low

Active High
MENU D2_OUT D2_OUT Tch2Pt Tch2Pt TchSPt1 TchSPt1 50mm
Tch2Pt TchSPt2 TchSPt2 12000mm
D2_OUT TchMid TchMid WndSize WndSize +00020mm

TchMid TchMdPt TchMdPt 6000mm
MENU MEASURE MEASURE Speed Fast
Standard
TchMid Offset Offset 0 mm
Medium
D2_OUT AdjSPt1 AdjSPt1 +00050mm Slow
D2_OUT AdjSPt2 AdjSPt2 +12000mm
D2_OUT Mode Mode Alarm MENU DISPLAY DISPLAY Units Units mm
Units in
Mode Health
Mode Swtch DISPLAY Zero Zero Near
Mode Swtch Zero Far
Mode Wnd DISPLAY Shift Shift Off
Mode Wnd Shift SetZero
Mode PFM Shift AutoSet
(in SPt mode only) D2_OUT SPtRef SPtRef Object DISPLAY View View Normal
View Invert
SPtRef Backgrnd
SPtRef Custom DISPLAY Sleep Sleep Disabled
(in SPtRef Custom Sleep 1min
mode only)
D2_OUT Offset Offset 0 mm
Sleep 5min
Sleep 15min
D2_OUT Timer Timer OffDly OffDly 0 ms Sleep 60min
Timer Off1Sho Off1Sho 0 ms

Timer OnDly OnDly 0 ms
Timer On1Sho On1Sho 0 ms MENU INFO INFO Model Model LTF12K
INFO P/N P/N 801130
D2_OUT Polarity Polarity PNP
INFO S/N S/N F..S..P..D..
Polarity NPN
INFO Version Version 1.0.0
Default Setting
MENU RESET RESET No

RESET Yes

9 Accessories
9.1 Cordsets
All measurements are listed in millimeters, unless noted otherwise.
5-Pin Threaded M12/Euro-Style Cordsets—with Shield
Model Length Style Dimensions Pinout (Female)
MQDEC2-506 1.83 m (6 ft)

44 Typ.
MQDEC2-515 4.57 m (15 ft)
Straight
MQDEC2-530 9.14 m (30 ft) 2
M12 x 1
1
MQDEC2-550 15.2 m (50 ft) ø 14.5
3
4 5
MQDEC2-506RA 1.83 m (6 ft)
32 Typ.
[1.26"] 1 = Brown
MQDEC2-515RA 4.57 m (15 ft)
2 = White
MQDEC2-530RA 9.14 m (30 ft) 30 Typ. 3 = Blue
Right-Angle [1.18"] 4 = Black
5 = Gray
MQDEC2-550RA 15.2 m (50 ft) M12 x 1
ø 14.5 [0.57"]
4-Pin Threaded M12/Euro-Style Cordsets—Double Ended
Model Length Style Dimensions Pinout
MQDEC-401SS 0.31 m (1 ft)

40 Typ.
[1.58"]
MQDEC-412SS 3.66 m (12 ft) M12 x 1

ø 14.5 [0.57"] Female
Male Straight/
MQDEC-420SS 6.10 m (20 ft) Female Straight 44 Typ.
[1.73"] 2
MQDEC-430SS 9.14 m (30 ft)
1
3
4
M12 x 1
ø 14.5 [0.57"]
MQDEC-450SS 15.2 m (50 ft) Male
1
MQDEC-403RS 0.91 m (1 ft) 2
32 Typ.
MQDEC-406RS 1.83 m (3 ft)
[1.26"] 4
3
30 Typ.
MQDEC-412RS 3.66 m (12 ft) 1 = Brown
[1.18"]
2 = White
MQDEC-420RS 6.10 m (20 ft) Male Right-Angle/ 3 = Blue
M12 x 1
Female Straight 4 = Black
MQDEC-430RS 9.14 m (30 ft) ø 14.5 [0.57"]
ø 14.5 [0.57"]
44 Typ. M12 x 1
MQDEC-450RS 15.2 m (50 ft)
[1.73"]
9.2 Brackets
All measurements are listed in millimeters, unless noted otherwise.

SMBLTFFA 67 SMBLTFL
75
• Swivel plate bracket • Right-angle bracket
• 5 mm stainless steel • 12 gauge stainless steel 4X Ø4.5
66
90 4X Ø4.5
4X M4X0.7 2X Ø5.7
37
3/8-16 UNC X
3 in. 40
SMBLTFU SMBAMSLTFP 85
• Enclosed bracket 42 • AMS mounting pattern
90
6X Ø3.5
• 16 gauge stainless steel • 12 gauge stainless steel
82 2X Ø4.5
134
2X Ø4.5 Ø4.5
2X Ø4.5
4X Ø5
45
SMBAMSLTFIP 85
• Includes the mounting
plate and two protective
windows 134
• 90 plus degree rotation
• Window frames are black
anodized aluminum;
mounting plate is
45
stainless steel
• The mounting plate,
SMBAMSLTFP, can be
ordered separately
• The replacement
window, RWAMSLTF,
can be ordered
separately

10 Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will
repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This
warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING
OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR
WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection
applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval
by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product
specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most
recent version of any documentation, refer to: www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.

Sensor Lazer

Uploaded by

Document Informationclick to expand document informationsensor

Document Informationclick to expand document information

Copyright:

Available Formats

Sensor Lazer

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sensor Lazer

Uploaded by

Copyright:

Available Formats

L-GAGE® LTF Time of Flight Laser Distance

Sensor with IO-Link

• High performance time of flight measurement

WARNING: Not To Be Used for Personnel Protection

www.bannerengineering.com - Tel: + 1 888 373 6767 3

1.2.1 Features and Indicators

Power LED Display Power LED Indicator

Figure 2. Display shown in Run Mode

Down and Up Buttons

4 www.bannerengineering.com - Tel: + 1 888 373 6767

Important: Pressing Escape discards any unsaved programming changes.

1.3 Laser Description and Safety Information

1.3 Class 2 Laser Models

For Safe Laser Use - Class 2 Lasers

Figure 3. FDA (CDRH) warning label (Class

www.bannerengineering.com - Tel: + 1 888 373 6767 5

2.1 Mount the Sensor

2.2 Wiring Diagrams

6 www.bannerengineering.com - Tel: + 1 888 373 6767

from Run Mode

See Quick Menu on page 7 See Sensor Menu (MENU) on page 8

Figure 5. Accessing the Menus

3.1 Quick Menu

D1 SPt2*(value) Save setting

Spt2 not available unless in

www.bannerengineering.com - Tel: + 1 888 373 6767 7

3.2 Sensor Menu (MENU)

3.3 Remote Input

8 www.bannerengineering.com - Tel: + 1 888 373 6767

NOTE: Follow procedure for the TEACH/SET method

1x Teaching..(D1SPt1) TchSPt1 (D1) with measurement value, then to TchSPt2 (D1)

1x D1 Sensor Mode D1-Mode with current value

1x Set Mode to Alarm, then back to Run mode

2x D2 Sensor Mode D2-Mode with current value

3x Window Size WndSize with value

www.bannerengineering.com - Tel: + 1 888 373 6767 9

Table 1: Remote TEACH Window Sizes

X3 100 100 X6 11950 23950

3.4 Locking and Unlocking the Sensor

Remote Input Instructions

2. Access the lock/unlock function.

T T T T "LOCK" and the current status (unlocked or

3. Lock or unlock the sensor.

T "Unlocked" flashes and the sensor returns

"Locked" flashes and the sensor returns to

3.5 Discrete Output Menu

10 www.bannerengineering.com - Tel: + 1 888 373 6767

D1_OUT AdjSPt2 AdjSPt2 +12000mm D2_OUT AdjSPt2 AdjSPt2 +12000mm

D1_OUT Mode Mode Alarm D2_OUT Mode Mode Alarm

Polarity PNP Timer On1Sho On1Sho 0 ms

3.5.1 Two-Point TEACH

The target's distance measurement value

2. Access the TEACH mode and TEACH the sensor.

The selected TEACH mode and "Teaching"

3. Repeat steps 1 to 2 for the other switch point, if desired.

www.bannerengineering.com - Tel: + 1 888 373 6767 11

1. Access the TEACH mode.