All manuals and user guides at all-guides.

com
  Quick Start Guide of CV10- ControlVIT Series

❶ Safety precautions
 Do not refit the inverter unauthorizedly; otherwise fire, electric shock or other injury may occur.
 Please install the inverter on fire-retardant material and keep the inverter away from combustible materials.
 Connect the braking optional parts according to the wiring diagram.
 Do not operate on the inverter if there is any damage or components loss to the inverter.
 Do not touch the inverter with wet items or body, otherwise electric shock may occur.

 Only qualified electricians are allowed to operate on the inverter.

 Do not carry out any wiring and inspection or changing components when the power supply is applied. Ensure all input power supply is disconnected before wiring and checking and
always wait for at least the time designated on the inverter (5 minutes) or until the DC bus voltage is less than 36V.

❷ Unpacking inspection
Check as followings after receiving products:

m
1. Check that there are no damage and humidification to the package. If not, please contact with our company.
2. Check the information on the type designation label on the outside of the package to verify that the drive is the correct type. If not, please contact with our company.
3. Check that there are no signs of water in the package and no signs of damage or breach to the inverter. If not, please contact with our company.
4. Check the information on the type designation label on the outside of the package to verify that the name plate is the correct type. If not, please contact with our company.
5. Check to ensure the accessories (including user’s manual and control keypad) inside the device is complete. If not, please contact with our company.

.co
❸ Installation
●Installation environment
The installation environment is the safeguard for a full performance and long-term stable functions of the inverter. Check the installation environment as followings:

Environment Conditions
Installation site Indoor
0℃ ~＋40℃, and the temperature changing rate is less than 0.5℃/minute.
If the ambient temperature of the inverter is above 40℃, derate 3% for every additional 1℃.
es
It is not recommended to use the inverter if the ambient temperature is above 50℃.
Environment
In order to improve the reliability of the device, do not use the inverter if the ambient temperature changes frequently.
temperature
Please provide cooling fan or air conditioner to control the internal ambient temperature below the required one if the inverter is used in a close space such as in the control cabinet.
When the temperature is too low, if the inverter needs to restart to run after a long stop, it is necessary to provide an external heating device to increase the internal temperature,
otherwise damage to the devices may occur.
RH≤90%
Humidity No condensation is allowed.
The maximum relative humidity should be equal to or less than 60% in corrosive air.
uid

Storage
-40 ℃~＋70℃, and the temperature changing rate is less than 1℃/minute.
temperature
The installation site of the inverter should:
- Keep away from the electromagnetic radiation source
Running environment
- Keep away from contaminative air, such as corrosive gas, oil mist and flammable gas;
condition
- Ensure foreign objects, such as metal power, dust, oil, water can not enter into the inverter(do not install the inverter on the flammable materials such as wood)
- Keep away from direct sunlight, oil mist, steam and vibration environment.
Below 1000m
Altitude
If the sea level is above 1000m, please derate 1% for every additional 100m.
Vibration ≤ 5.8m/s2(0.6g)
-g

Installation direction The inverter should be installed on an upright position to ensure sufficient cooling effect.
Note: CV10 inverters should be installed in a clean and ventilated environment according to enclosure classification. Cooling air must be clean, free from corrosive materials and electrically conductive dust.

●Installation space and direction

all

Note: CV10 is wall mountable, and the minimum space of A and B is 100mm.

1/5 EL086A01
 All manuals and user guides at all-guides.com
  Quick Start Guide of CV10- ControlVIT Series
Terminal
❹ Standard wiring name
Description

ROA RO relay output

Ground the inverter Contactor capability: 3A/AC250V, 1A/DC30V
ROC
Check the ratings of the circuit breaker +10V Local power supply +10V
Check whether the motor voltage and power are compatible with those of the inverter 1. Input range: AI voltage and current can be chosen: 0~10V/0~20mA; can be shifted by
J3 , -10V~+10V
●4.1 Main circuit AI
2. Input impedance: voltage input: 20kΩ; current input: 500Ω
3. Resolution: the minimum one is 5mV when 10V corresponds to 50Hz
4. Deviation ±1%, 25℃
Note: the potentiometer sets AI1 parameters and AI terminal sets AI2 parameters.
1. Output range: 0~10V or 0~20mA
AO 2. The voltage or the current output depends on the jumper
3. Deviation±1%,25℃
24V Local 24V power supply
GND +10V reference zero potential
S1 Switch input 1 1. Internal impedance: 3.3kΩ
2. 0~4V corresponds to low level input and 7~30V
S2 Switch input 2
corresponds to high level input
L N (+) PB U V W 3. Max input frequency:1kHz
S3 Switch input 3
4. All are programmable digital input terminal. User can set
S4 Switch input 4 the terminal function through function codes.
●4.2 Control circuit S5 Switch input 5 Common terminal for S5 and Y, can be switched by J1
Y Digital output terminal Note: S5 and Y can not be used at the same time.

485 communication interface and 485 differential signal interface

485+
If it is the standard 485 communication interface, please use twisted pairs or shielded
485- cable.

●5.2 Displaying
The keypad displays as following after power on:

NO. Name Content

Display the running frequency

Normal RUN/TUNE LED is on
Hz LED is on

The displaying is determined by the fault type

Please refer to the fault solutions of the operation
Fault
manual of CV10 products

(for example: external fault) TRIP LED is on

●5.3 Parameters setting

○
“ ”: means the set value of the parameter can be modified on stop and running state；
“◎”: means the set value of the parameter can not be modified on the running state；
●
“ ”: means the value of the parameter is the real detection value which can not be modified.

Note: Automatic check constraints are available to avoid errors for the modifying of the parameters.
❺ Operation and start up Default
Code Name Detailed instruction of parameters Modify
value
●5.1 Power on
P00 Group Basic function group
Power on after checking as followings: Speed control
P00.00 2:SVPWM control 2 ◎
mode
Checking Content
P00.01
Run command
channel
0:Keypad
1:Terminals
2:Communication
0 ○
Please check the voltage. Single phase 230V: Max. output
P00.03 P00.04~400.00Hz 50.00Hz ◎
frequency
220V(-15%)~240V(+10%)
Voltage of the power supply Upper limit of
Ground the input terminals, L and N, with proper techniques P00.04 the running P00.05~P00.03 (Max. output frequency) 50.00Hz ◎
frequency
Check the inverter and the motor are grounded correctly
Lower limit of
Connection between output P00.05 the running 0.00Hz~P00.04 (Upper limit of the running frequency) 0.00Hz ◎
Please ensure the output terminals of the inverter are frequency
terminals of the inverter and
connected tightly with the motor terminals A frequency 0:Keypad
motor terminals P00.06 command 1:Analog AI1(corresponding to keypad potentiometer) 0 ○
Connection of the terminals Please ensure the terminals of the control circuit are connected selection 2:Analog AI2(corresponding to terminal AI1)
B frequency 6: Multi-step speed running setting
of control circuit tightly with other control devices P00.07 command 7: PID control setting
8: MODBUS communication setting
2 ○
Control terminals of the Please ensure all terminals of the control circuit are on the selection
B frequency
inverter status of OFF
Loads status Please ensure whether the motor is non-load
P00.08
command
reference
0: Maximum output frequency
1: A frequency command
0 ○
selection
Combination of
Connect the inverter with the motor; Connect the inverter with the power supply P00.09 the setting
0:A，
3:A-B
1:B，
4:Max(A，B):
2:A+B，
5:Min(A，B):
0 ○
source
Terminal
Terminal name Function
P00.10
Keypad set
frequency
Setting range:0.00 Hz~P00.03(the Max. frequency) 50.00Hz ○
sign
L Single phase AC input terminals which are
P00.11 ACC time 1
Depends
on model
○
Power input of the main circuit 0.0~3600.0s
N generally connected with the power supply. P00.12 DEC time 1
Depends
on model
○
U Running
V The inverter output
3-phase AC output terminals which are generally
P00.13 direction
0: Runs at the default direction
1: Runs at the opposite direction
0 ○
connected with the motor. selection
W
Carrier
PB
Braking resistor terminal PB and (+) are connected to the external resistor.
P00.14 frequency 1.0~8.0kHz 4 kHz ○
setting
(+)
P00.16
AVR function
selection
0:Invalid
1:Valid during the whole procedure
1 ○
Grounding terminal Each machine has a standard PE terminal.
Function
0:No operation 1:Restore the default value
Note: P00.18 restore 0 ◎
2:Clear fault records
parameter
 Do not use asymmetrically motor cables. If there is a symmetrically grounding conductor in the motor
cable in addition to the conductive shield, connect the grounding conductor to the grounding terminal
at the inverter and motor ends.
 Route the motor cable, input power cable and control cables separately.
 C3 optional input filter is parallel-connected with the input of the inverter if selected.

2/5 EL086A01
 All manuals and user guides at all-guides.com
  Quick Start Guide of CV10- ControlVIT Series
●5.4 Motor and control parameters Code Name Detailed instruction of parameters
Default
Modify
value
·Please refer to the name plate setting of motors. selection 15: Shift between combination setting and B setting
16: Multi-step speed terminal 1
Default 17: Multi-step speed terminal 2
Code Name Detailed instruction of parameters Modify
value 18: Multi-step speed terminal 3
19: Multi- step speed terminal 4
P02 Group Motor 20: Multi- step speed pause
21: ACC/DEC time option 1
Rated power 25: PID control pause
of Depends 26: Traverse Pause (stop at the current frequency)
P02.01 ◎
asynchronous on model 27: Traverse reset (return to the center frequency)
motor 28: Counter reset
Rated 30: ACC/DEC prohibition
frequency of 31: Counter trigger
P02.02 50.00Hz ◎
asynchronous Set the parameter of the controlled asynchronous motor. 33: Cancel the frequency change setting temporarily
motor In order to ensure the controlling performance, set the 34: DC brake
Rated speed P2.01~P2.05 according to the name plate of the 36: Shift the command to the keypad
of asynchronous motor. Depends 37: Shift the command to the terminals
P02.03 ◎ 38: Shift the command to the communication
asynchronous In order to ensure the controlling performance, please on model
motor configure the motor according to the standard principles, if
Rated voltage the gap between the motor and the standard one is huge, P05. 32
Lower limit of AI1 is set by the analog potentiometer
AI1 0.00V~P05.34
0.00V ○
of the features of the inverter will decrease. Depends Corresponding
P02.04 ◎
asynchronous on model
motor P05.33
setting of the
lower limit of
-100.0%~100.0% 0.0% ○
Rated current AI1
of Depends
P02.05
asynchronous on model
◎ P05.34
Upper limit of
AI1
P05.32~10.00V 10.00V ○
motor Corresponding
Stator resistor
P05.35
setting of
-100.0%~100.0% 100.0% ○
P02.06
of
asynchronous
Depends
on model
○ the upper limit
of AI1
motor
Rotor resistor P05.36
AI1 input filter
time
0.000s~10.000s 0.100s ○
P02.07
of
asynchronous
Depends
on model
○ P05.37
Lower limit of AI2 is set by control terminal
0.00V ○
AI2 0.00V~P05.39
motor
Corresponding
Leakage
P02.08
inductance of
These parameters are basic parameters controlled by
vectors which directly impact the features.
Depends
○ P05.38
setting of the
lower limit of
-100.0%~100.0% 0.0% ○
asynchronous on model
Note: Users cannot modify the parameters freely. AI2
motor
Mutual P05.39
Upper limit of
AI2
P05.37~10.00V 10.00V ○
P02.09
inductance of
asynchronous
Depends
on model
○ Corresponding
motor P05.40
setting of
the upper limit
-100.0%~100.0% 100.0% ○
Non-load
of AI2
P02.10
current of
asynchronous
Depends
on model
○ P05.41
AI2 input filter
0.000s~10.000s 0.100s ○
motor time
0:No protection
Motor
1: Common motor (with low speed compensation).
P06 Group Output terminals
P02.26 overload 2 ◎
2: Frequency conversion motor (without low speed 0: Invalid
protection
compensation) P06.01
Y output
selection 1: On operation 0 ○
Motor 2: Forward rotation operation
P02.27
overload
protection
Times of motor overload M = Iout/(In*K)
20.0%~120.0%
100.0% ○ 3: Reverse rotation operation
4: Jogging operation
coefficient 5: The inverter fault
6: Frequency degree test FDT1
P04 Group SVPWM control 7: Frequency degree test FDT2
8: Frequency arrival
Motor V/F 0:Straight line V/F curve； 9: Zero speed running
P04.00 0 ◎
curve setting 1:Multi-dots V/F curve 10: Upper limit frequency arrival
P04.01 Torque boost 0.0% ○ Relay RO 11: Lower limit frequency arrival
Torque boost P06.03 output 12: Ready for operation 1 ○
P04.02 20.0% ○ selection 14: Overload pre-alarm
close
15: Underload pre-alarm
Motor V/F The setting range of P04.01:0.0%: 16: Completion of simple PLC stage
P04.03 frequency (automatic) 0.1%~10.0% 0.00Hz ○ 17: Completion of simple PLC cycle
point 1 The setting range of P04.02: 0.0%~50.0% 18: Setting count value arrival
Motor V/F Note: V1＜V2＜V3, f1＜f2＜f3. Too high low frequency 19: Defined count value arrival
P04.04 voltage voltage will heat the motor excessively or damage. The 20: External fault valid
inverter may occur in the overcurrent speed or overcurrent 00.0% ○
point 1 22: Running time arrival
protection. 23: MODBUS communication virtual terminals output
Motor V/F
P04.05 frequency The setting range of P04.03: 0.00Hz~P04.05 00.00Hz ○ When the current bit is set to 0, input terminal is positive.
point 2 The setting range of P04.04, P04.06 and P04.08 : When the current bit is set to 1, input terminal is negative.
Motor V/F 0.0%~110.0% Polarity of
P04.06
voltage point 2 The setting range of P04.05: P04.03~ P04.07 00.0% ○ P06.05 output BIT3 BIT2  BIT1  BIT0  00 ○  
The setting range of P04.07: P04.05~P02.02 (the rated terminals Reserved RO1 Reserved Y
Motor V/F
P04.07 frequency frequency of motor) 00.00Hz ○ Setting range: 00~0F
point 3
Y switching on 0.000s
Motor V/F P06.06 0.000~50.000s ○
P04.08 00.0% ○ delay time
voltage point 3
Y switching off 0.000s
△f=fb-n*p/60 P06.07 0.000~50.000s ○
delay time
Of which, fb is the rated frequency of the motor, its function
code is P02.02; n is the rated rotating speed of the motor RO switching
Motor V/F slip P06.10 0.000s ○
and its function code is P02.03; p is the pole pair of the on delay time
P04.09 compensation 0% ○ 0.000~50.000s
motor. 100.0% corresponds to the rated slip frequency △f. RO switching
gain P06.11 0.000s ○
Note: no torque compensation for single-phase 220V off delay time
inverters 0:Running frequency
Setting range: 0.0~200.0% 1:Set frequency
Low frequency 2:Ramp reference frequency
P04.10 vibration 10 ○ 3:Running rotation speed
control factor 4:Output current (relative to the rated current of the
High The setting range of P04.10: 0~100 inverter)
frequency The setting range of P04.11: 0~100 5:Output current(relative to the rated current of the motor)
P04.11
vibration The setting range of P04.12: 0.00Hz~P00.03 (the Max.
10 ○ P06.14 AO output 6:Output voltage 0 ○
control factor frequency) 7:Output power
8:Set torque value
Vibration
9:Output torque
P04.12 control 30.00 Hz ○
10:Analog AI1 input value
threshold
11:Analog AI2 input value
Energy-saving 0: No operation 14:MODBUS communication set value 1
P04.26 0 ◎
operation 1: Automatic energy-saving 15:MODBUS communication set value 2
Lower limit of
P05 Group Input terminals P06.17
AO output
0.0% ○

S1 terminal 0: No function Corresponding When the analog output is current output, 1mA equals to
P05.01 function 1: Forward rotation operation 1 ◎ P06.18 AO output to 0.5V. 0.00V ○  
selection 2: Reverse rotation operation the lower limit In different cases, the corresponding analog output of
S2 terminal 3: 3-wire control operation Upper limit of 100% of the output value is different. Please refer to each
4: Forward rotation jogging P06.19 100.0% ○
P05.02 function 4 ◎ AO output application for detailed information.
selection 5: Reverse rotation jogging The Setting range of P06.18: 0.00V~10.00V
6: Coast to stop corresponding Setting range of P06.19: P06.17~100.0%
P05.03
S3 terminal
function
7: Fault reset
7 ◎
P06.20
AO output to Setting range of P06.20: 0.00V~10.00V
10.00V ○  
8: Operation pause the upper limit Setting range of P06.21: 0.000s~10.000s
selection
9: External fault input
S4 terminal 10: Increasing frequency setting (UP) AO output
P06.21 0.000s ○
P05.04 function 11: Decreasing frequency setting (DOWN) 0 ◎ filter time
selection 12: Cancel the frequency change setting
P05.05
S5 terminal 13: Shift between A setting and B setting
0 ◎
 
function 14: Shift between combination setting and A setting

3/5 EL086A01
 All manuals and user guides at all-guides.com
  Quick Start Guide of CV10- ControlVIT Series
●5.6 Stop (press STOP/RST)
P07 Group Human-Machine Interface
Ensure the motor runs at right direction and there is no fault.
Current fault 0: No fault
P07.27
type 4: OC1
●
Previous fault 5: OC2
P07.28 ●
type
Previous 2
6: OC3
7: OV1 ❻ Diagram of quick start-up
P07.29
fault type
8: OV2 ●
9: OV3
Previous 3 10: UV
P07.30
fault type
●
11: Motor overload (OL1)
Previous 4 12: The inverter overload (OL2)
P07.31
fault type 15: Overheat of the rectifier module (OH1) ●
16: Overheat fault of the inverter module (OH2)
17: External fault (EF)
18: 485 communication fault (CE)
Previous 5 21: EEPROM operation fault (EEP)
P07.32
fault type 22: PID response offline fault (PIDE) ●  
24: Running time arrival (END)
25: Electrical overload (OL3)
36: Undervoltage fault (LL)
Current fault
P07.33 running 0.00Hz ●
frequency
Ramp
reference
P07.34
frequency at
0.00Hz ●
current fault
Output voltage
P07.35
at current fault
0V ●
Output current
P07.36
at current fault
0.0A ●
Bus voltage at
P07.37
current fault
0.0V ●
Max.
P07.38 temperature at 0.0℃ ●
current fault
Input terminal
P07.39 state at 0 ●
current fault
Output
P07.40 terminal state 0 ●
at current fault

P08 Group Enhanced function

Time of fault
P08.28 0 ○
reset
Setting range of P08.28:0~10
Interval time of Setting range of P08.29:0.1~3600.0s
P08.29 automatic fault 1.0s ○
reset
Energy
0:Disabled
P08.37 Braking 0 ○
1:Enabled
enable

P11 Group Protective parameters

Sudden power
loss frequency
0: Enabled
P11.01 decreasing
1: Disabled
0 ○  
function
selection
Frequency
decreasing Setting range: 0.00Hz/s~P00.03 (the Max. frequency)
P11.02
ratio of sudden Frequency-decreasing point of sudden power loss: 260V
10.00Hz/s ○  
power loss
Overvoltage
0:Disabled
P11.03 speed loss
1:Enabled
1 ○  
protection
Overvoltage
speed loss
P11.04 120~150% 120% ○
voltage
protection
Current limit
P11.05 action 1 ◎
selection
Setting range of P11.05:
Automatic
0:current limit invalid
P11.06 current limit 160.0% ◎
level
1:current limit valid
Setting range of P11.06:50.0~200.0% ❼ Fault diagnosis and countermeasures
The Setting range of P11.07:0.00~50.00Hz/s
decreasing Do as the following after the inverter fault:
P11.07 10.00Hz/s ◎
ratio during 1. Check to ensure there is nothing wrong with the keypad. If not, please contact with SALICRU.
current limit
2. If there is nothing wrong, please check P07 and ensure the corresponding recorded fault parameters
Overload Setting range of P11.08: 0x000~0x131
pre-alarm of LED ones: to confirm the real state when the current fault occurs by all parameters.
P11.08
the motor or 0: Overload pre-alarm of the motor, comply with the rated
0x000 ○  
3. See the following table for detailed solution and check the corresponding abnormal state.
the inverter current of the motor
Overload 1: Overload pre-alarm of the inverter, comply with the 4. Eliminate the fault and ask for relative help.
P11.09 pre-alarm test rated current of the inverter
LED tens:
150% ○   5. Check to eliminate the fault and carry out fault reset to run the inverter.
level
0: The inverter continues to work after underload pre-alarm
1: The inverter continues to work after underload pre-alarm Fault code Fault type Possible cause Solutions
and the inverter stops to run after overload fault
2: The inverter continues to work after overload pre-alarm Over-current when 1. The acceleration or 1. Increase the ACC time
OC1
and the inverter stops to run after underload fault acceleration deceleration is too fast. 2. Check the input power
Overload 2. The voltage of the grid is 3. Select the inverter with a
Over-current when
P11.10 pre-alarm 3: The inverter stops when overloading or underloading. 1.0s ○   OC2
deceleration too low. larger power
detection time LED hundreds: 3. The power of the inverter is 4. Check if the load is short
0: Detection all the time
1: Detection in constant running too low. circuited (the grounding short
Setting range of P11.09: P11.11~200% 4. The load transients or circuited or the wire short
Setting range of P11.10: 0.1~60.0s rotation is abnormal. circuited) or the rotation is not
Over-current when 5. The grounding is short smooth.
Detection level circuited or the output is 5. Check the output
OC3 constant speed
of the
P11.11
underload
50% ○   running phase loss. configuration.
6. There is strong external 6. Check if there is strong
pre-alarm Setting range of P11.11: 0~P11.09 interference. interference.
Detection time Setting range of P11.12: 0.1~60.0s 7. The overvoltage stall 7. Check the setting of relative
of the
P11.12
underload
1.0s ○   Over-voltage when
protection is not opened. function codes.
1. Check the input power
pre-alarm OV1
acceleration 2. Check if the DEC time of the
1. The input voltage is
0x00~0x11 Over-voltage when load is too short or the inverter
OV2 abnormal.
LED ones: deceleration starts during the rotation of the
Output 2. There is large energy
0: Action under fault undervoltage motor or it needs to add the
terminal action feedback.
P11.13
selection
1: No action under fault undervoltage 0x00 ○   Over-voltage when 3. No braking components.
dynamic braking components.
LED tens: 3. Install the braking
during fault OV3 constant speed 4. Dynamic braking energy
0: Action during the automatic reset components.
running unit is not activated
1: No action during the automatic reset 4. Check the setting of relative
function codes.

●5.5 Start up (press RUN/TUNE)

4/5 EL086A01
 All manuals and user guides at all-guides.com
  Quick Start Guide of CV10- ControlVIT Series
Fault code Fault type Possible cause Solutions Fault code Fault type Possible cause Solutions
1. The voltage of the power 1. Check the input power of 3. The communication address.
DC bus supply is too low. the supply line. address is wrong. 4. Change or replace the
UV
Under-voltage 2. The overvoltage stall 2. Check the setting of relative 4. There is strong interference connection distribution or
protection is not opened. function codes. to the communication. improve the anti-interference
1. The voltage of the power 1. Check the power of the capability.
supply is too low. supply line 1. Error of controlling the write 1. Press STOP/RST to reset
2. The motor setting rated 2. Reset the rated current of EEP EEPROM fault and read of the parameters 2. Change the main control
OL1 Motor overload
current is incorrect. the motor 2. Damage to EEPROM panel
3. The motor stall or load 3. Check the load and adjust 1. Check the PID feedback
transients are too strong. the torque lift 1. PID feedback offline
signal
PIDE PID feedback fault 2. PID feedback source
1. The acceleration is too fast 2. Check the PID feedback
1. Increase the ACC time disappear
2. Reset the rotating motor source
2. Avoid the restarting after
3. The voltage of the power The actual running time of the
stopping. Time reach of factory Ask for the supplier and adjust
supply is too low. END inverter is above the internal
3. Check the power of the setting the setting running time.
OL2 Inverter overload 4. The load is too heavy. setting running time.
supply line
5. Close loop vector control, The inverter will report the
4. Select an inverter with Electronic underload Check the load and the
reverse direction of the code LL underload pre-alarm
bigger power. fault underload pre-alarm point.
panel and long low-speed according to the set value.
5. Select a proper motor.
operation
The inverter will report
OL3 Electrical overload overload pre-alarm according
Check the load and the ●Other states
overload pre-alarm point.
to the set value.
Fault code Fault type Possible cause Solutions
OH1 Rectifier overheat 1. Refer to the overcurrent
solution PoFF System power off System power off or low DC voltage Check the grid
2. Redistribute
dredge the wind channel or
1. Air duct jam or fan damage
change the fan ●Fault reset
2. Ambient temperature is too
3. Low the ambient
high. The inverter can be reset by STOP/RST, digital input, and power switching-off. After the problems
OH2 IGBT overheat temperature
3. The time of overload
4. Check and reconnect settlement, the motor can be restarted.
running is too long.
5. Change the power
6. Change the power unit
7. Change the main control
panel Only qualified trained people can settle the fault and please do as the “safety precautions”.
S1~S5 external fault input Check the external device
EF External fault
terminals action input
1. The baud rate setting is 1. Set proper baud rate
incorrect. 2. Check the communication
CE Communication error
2. Fault occurs to the connection distribution
communication wiring. 3. Set proper communication

5/5 EL086A01