Variable Displacements Axial Piston Pumps: Edition: 06/06.2020 Replaces: MVP 05 T A

MVP 06 T A Edition: 06/06.
2020 Replaces: MVP 05 T A
VARIABLE
DISPLACEMENTS
Headquarters:
AXIAL PISTON
CASAPPA S.p.A.
Via Balestrieri, 1 PUMPS
43044 Lemignano di Collecchio
Parma (Italy)
Tel. (+39) 0521 30 41 11
Fax (+39) 0521 80 46 00
E-mail: [email protected]
www.casappa.com
MVP
INDEX
Section Page
INTRODUCTION.................................................................................................................................................................. 3
GENERAL INFORMATION / INSTRUCTIONS....................................................................................................................... 4
MOUNTING POSITIONS...................................................................................................................................................... 5
DISPLACEMENTS AND WORKING PRESSURES RANGE..................................................................................................... 6
FEATURES.......................................................................................................................................................................... 7
DISPLACEMENT SETTING................................................................................................................................................. 12
CENTER OF GRAVITY........................................................................................................................................................ 12
OPERATING CURVES......................................................................................................................................................... 13
SINGLE PUMPS AND COMMON INLET MULTIPLE PUMPS

DIMENSIONS.................................................................................................................................................................... 20
DRIVE SHAFTS.................................................................................................................................................................. 32
MOUNTING FLANGES........................................................................................................................................................ 36
PORTS TYPE..................................................................................................................................................................... 38
REGULATORS.................................................................................................................................................................... 41
MULTIPLE PUMPS WITH THROUGH DRIVE....................................................................................................................... 53
HOW TO ORDER................................................................................................................................................................ 64
O 06/06.2020
O Modification from former edition.
2 DCAT048-ID02
MVP
INTRODUCTION
Variable displacement axial piston pumps swash plate design ideally suited for medium and high pressure open
circuit applications. The compact design allows to be mounted directly on engine motors.
Replaces: 05/10.2014
DISPLACEMENTS TYPICAL APPLICATIONS

From 14 cm3/rev (0.85 in3/rev) z
Skid Steer Loaders
To 84,7 cm3/rev (5.17 in3/rev) z
Wheel Loaders - Backhoe Loaders
PRESSURE O z
Mini and Midi-Excavators
Max. constant operating pressure 280 bar (4060 psi) z
Telehandlers
Max. system pressure (relief valve setting) 315 bar (4568 psi) z
Forklifts
Max. peak of pressure 350 bar (5075 psi) z
Windmills - Green Energy
z
Tractors & Attachements
SPEED
Max. 3500 min-1
APPLICATION
Medium, high pressure
SECTOR
Mobile
O
1 2 3 4 5 6
1 Pump body
2 Swash plate
3 Cylinders block
4 Counterbalancing spring
5 Plug
6 Max. displacement limiter
7 Cover
8 Valve plate
9 Min. displacement limiter
10 Piston
11 Piston guide plate
O 06/06.2020
11 10 9 8 7
z
Compact design z
Drive shaft bearing suitable for
z
Longer service life radial and axial loads
z
Low noise emission z
Hydraulic and Electro-hydraulic
displacement controls
z
Max. and min. displacement limiter
GENERAL NOTES
For some configuration the double shaft seals is available.
For more information please consult our pre-sales department.
DCAT048-ID02 3
MVP
GENERAL INFORMATION / INSTRUCTIONS
DIRECTION OF ROTATION LINES

Clockwise or anti-clockwise defined looking at the drive shaft. The lines must have a major diameter which is at least as large
as the diameter of pump ports, and must be perfectly sealed.
HYDRAULIC FLUID To reduce loss of power, the lines should be as short as possi-
Mineral oil based hydraulic fluid conforming to DIN 51524, ble, reducing the sources of hydraulic resistance (elbow, throt-
fire resistant fluids and biodegradable fluids according to the tling, gate valves, etc.) to a minimum. A length of flexible tub-
technical data shown in the tables on pages 5 ÷ 7. The system ing is recommended to reduce the transmission of vibrations.
should be designed to prevent aeration of the hydraulic fluid. Before connecting the lines, remove any plug and make sure
that the lines are perfectly clean. Check that the drain line is
FLUID VISCOSITY dimensioned in a way to guarantee a case pressure lower than
The fluid viscosity range for optimal use of MVP pump is 1,5 bar (22 psi) absolute. The drain line must be connected
between 15 and 35 cSt (77 and 163 SSU). directly (no filter, no valves, no oil cooler) to the tank and must
Functional limit conditions are: terminate below the oil level. Check that the dimensions of the
max.: 1500 cSt (6818 SSU) at start up at minimum tempera suction line guarantee a pressure equal or superior to 0,8 bar
ture of -25 °C (-13 °F) with straight and short inlet line. (12 psi). Inlet pressure less than 0,8 bar (12 psi) could cause an
min.: 10 cSt (58 SSU) at maximum temperature of 110 °C increase of noise emission, the decrease of the pump perfor-
(230 °F) mances and a reduction of its life expectancy.
FILTRATION STARTING UP
To ensure the optimal performance and the maximum life to Check that all connections are secure and that the entire sys-
the pump, the hydraulic fluid must have and maintain a fluid tem is completely clean. Add oil to the tank always using a
contamination within the values shown in the table below. filter. Bleed the air from the circuit to help the filling. Turn on
the system for a few moments at minimum speed, then bleed
the circuit again and check the level of oil in the tank. Gradually
Working pressure Δp < 140 140 < Δp < 210 Δp > 210 increase the pressure and speed of rotation up to the pre-set
bar (psi) (2030) (2030) (3045) (3045) operating levels, which must stay within the stated limits as
Contamination
specified in the catalogue.
9 8 7
class NAS 1638
Contamination FOR VERY LOW TEMPERATURE
class ISO 20/18/15 19/17/14 18/16/13
4406:1999 STARTING UP
Achieved with We strongly recommend to warm up the oil before running the
filter ßx(c) ≥75 machine. If this is not possible, the warm up of the oil and of
10 μm 10 μm 10 μm
according to ISO the pump should be carried out following these instructions:
16889 • Start the pump in stand-by condition at minimum speed.
Keep this working condition until the pump case reaches
-20 °C (-4 °F)
• Increase slowly the displacement.Max pressure permitted:
Casappa recommends to use its own 50 bar (725 psi). The maximum permitted speed is strictly
production filters: connected to the layout of the inlet circuit; check that there
is no cavitation before increasing the speed.
• Keep this working condition until the oil temperature in the
whole system is -10 °C (14 °F).
STORAGE • Maximum pressure can be achieved from now on.
The storage must be in a dry environment. • Always check the outlet flow to prevent cavitation damage.
05/10.2014
Max storage time in ideal conditions is 24 months.

The ideal storage temperature is between 5 °C (41 °F) and All the temperature are referred to oil with viscosity ISO VG 32
20 °C (68 °F). No problem in case of temperature between according to DIN 51 519.
-40 °C (-40 °F) and 50 °C (122 °F). Below -40 °C (-40 °F)
please consult our pre-sales department. SUGGESTIONS
To prevent cavitation at low temperature we suggest:
INSTALLATION • To warm up the tank
Check that the maximum coupling eccentricity stays within • To pressurize the tank
0,25 mm (0.0098 in) to reduce shaft loads due to misalign- • To oversize the inlet hose
ment. It is advised to use a flexible coupling suitable to absorb
eventual rotational shocks. For applications with axial and ra-
dial loads exceeding published standards, consult our sales
department. The direction of rotation of the pump must agree
with the prime mover rotation. Before installation, the case of
the pump must be filled with fluid.
4 DCAT048-ID02
MVP
MOUNTING POSITIONS
O
Standard pump is supplied with D1 drain hole open and D2,
D3, D4 plugged (u if available).
Before installation fill the pump with hydraulic oil for at least
3/4 of the volume keeping it in horizontal position.
The pump can be mounted in a horizontal or vertical position.

The highest of the case drain ports must be used to keep the
required filling oil.
If D1 is not the highest drain port it must be closed by moving
the plug from the hole chosen for the drain line.
The pump can be located above the oil level if the absolute
pressure at the inlet port stays within the stated limits.
With exception of pump mounted below the oil level, we rec-
ommend to interpose a baffle plate between inlet and drain
line.
To reduce further noise emission, we recommend to mount
the pump below the oil level and avoid suction lines with sharp
restrictions.
u u
HORIZONTAL MOUNTING VERTICAL MOUNTING
Arrangement inside the tank. Arrangement inside the tank.
Minimum oil level equal or above Minimum oil level equal or above
the pump mounting face. the pump mounting face.
A ≥ 200 mm (7.874 in) A ≥ 200 mm (7.874 in)
Arrangement inside the tank. Arrangement inside the tank.
Minimum oil level below the Minimum oil level below the
pump mounting face. pump mounting face.
Min. inlet pressure= 0,8 bar abs Min. inlet pressure= 0,8 bar abs
(24 in Hg) (24 in Hg)
B ≤ 800 mm (31.4961 in) B ≤ 800 mm (31.4961 in)
C = 200 mm (7.874 in) C = 200 mm (7.874 in)
Arrangement outside the tank above Arrangement outside the tank above
oil level. oil level.
Min. inlet pressure= 0,8 bar abs Min. inlet pressure= 0,8 bar abs
O 06/06.2020
(24 in Hg) (24 in Hg)

B ≤ 800 mm (31.4961 in) B ≤ 800 mm (31.4961 in)
C = 200 mm (7.874 in) C = 200 mm (7.874 in)
Arrangement outside the tank

below oil level.
C = 200 mm (7.874 in)
IN= inlet line - D1= drain line - A= min. distance between the line - B+C= permissible suction height - C= line immersion depth
DCAT048-ID02 5
MVP
DISPLACEMENTS AND WORKING PRESSURES RANGE
MVP-MVPD Comparison
28 34
Max. displacement (1.71) (2.07) 45 53 65 72 84
14
cm3/rev (in3/rev)
(0.85) (2.75) (3.23) (3.97) (4.39) (5.12)
 MVPD 30
MVP 30
Pump series
 MVPD 48
MVP 48
MVP 60
p1 - p3 p1 - p3 p1 - p3
Working pressure
bar (psi) 230 290 280 350 250 315
- - -
(3335) (4205) (4060) (5075) (3625) (4568)
: MVPD Series. For more information please consult the respective technical catalogue.
PRESSURE DEFINITION
O
p1 Constant operating pressure
p (bar) - (psi)
p3 p2 System pressure (relief valve setting)

p2 p3 Peak of pressure
O 06/06.2020
p1
The peak of pressure is the max pressure allowed and
it corresponds to the overshoot of the relief valve.
Please note that both relief valve setting and overshoot

must be lower than their limits.
T (s) If the relief setting is compliant but the overshoot is
Max. 20 s Max. 50 ms higher than the limit, the relief setting must be de-
creased until the overshoot is compliant to Casappa
limit.
For high frequency applications please consult our pre-

sales department.
6 DCAT048-ID02
MVP
FEATURES
Technical data with mineral oil
HL or HLP mineral oil based hydraulic fluid to DIN 51524

Pump type MVP 30·28 30·34 48·45 48·53 60·60 60·72 60·84
Max. displacment cm /rev
3
28 34,8 45 53,7 60 72 84,7
(theor.) Vmax (in3/rev) (1.71) (2.12) (2.75) (3.28) (3.66) (4.39) (5.17)
bar abs. 0.8
min.
(in Hg) (24)
Inlet pressure
bar abs. 25
max.
(psi) (363)
280 250 280 250 280 280 250
p1
(4060) (3625) (4060) (3625) (4060) (4060) (3625)
Max. outlet bar 315 280 315 280 315 315 280
p2
pressure pmax (psi) (4568) (4060) (4568) (4060) (4568) (4568) (4060)
350 315 350 315 350 350 315
p3
(5075) (4568) (5075) (4568) (5075) (5075) (4568)
Max. drain line bar abs. 1,5
O
pressure (psi) (22)
Max. speed nmax min-1 @ Vmax (1) 3500 2900 3000 2500 3000 2700 2300 O
98 101 135 134 180 194 212
@ nmax
(25.9) (26.7) (35.7) (35.4) (47.6) (51.3) (56.0)
Max. delivery l/min 56 70 90 107 120 144 169
@ 2000 min-1
(theor.) (US gpm) (14.8) (18.5) (23.8) (28.3) (31.7) (38.0) (44.7)
42 52 68 81 90 108 127
@ 1500 min-1
(11.1) (13.7) (18.0) (21.4) (23.8) (28.5) (33.6)
45,7 42,1 63 55,9 84 90,7 88,2
@ nmax
(61.2) (56.4) (84.4) (74.9) (112.6) (121.5) (118.2)
Max. power
kW 26,1 29 42 44,8 56 67,2 70,6
(theor.) (HP)
@ 2000 min-1
(35.0) (38.9) (56.3) (60.0) (75.0) (90.0) (94.6)
(Δp = pmax cont.)
19,6 21,8 31,5 33,6 42 50,4 52,9
@ 1500 min-1
(26.3) (29.2) (42.2) (45.0) (56.3) (67.5) (70.9)
124,8 138,5 200,5 213,7 267,4 320,9 337
@ pmax cont.
Max. torque Nm (1105) (1226) (1775) (1891) (2367) (2840) (2983)
(theor.) (lbf in) @ 100 bar 44,6 55,4 71,6 85,5 95,5 114,6 134,8
(1450 psi) (395) (490) (634) (757) (845) (1014) (1193)
Moment of inertia kgm2 0,002 0,002 0,003 0,003 0,008 0,008 0,008
rotary group (ft2 lbs) (0.05) (0.05) (0.07) (0.07) (0.19) (0.19) (0.19)
l 0,85 0,85 1 1 1,3 1,3 1,3
Fill volume (US gallons) (0.22) (0.22) (0.26) (0.26) (0.34) (0.34) (0.34)
O 06/06.2020
kg 15 15 19 19 22 22 22
Mass (approx.) (lbs) (33.1) (33.1) (41.9) (41.9) (48.5) (48.5) (48.5)
Seals N= Buna V= Viton
-25 -15
min.
(-13) (5)
Operating °C 80 110
max. cont.
temperature (°F) (176) (230)
100 125
max. peak
(212) (257)
(1) = with an inlet pressure of 1 bar abs (14.5 psi) and viscosity between 15 and 35 cSt (77 and 163 SSU).
Reducing the displacement or increasing the inlet pressure the max. speed changes. See table at page 10.
Max. speed limit are: MVP 30: 3500 m-1 – MVP 48: 3000 m-1 - MVP 60: 3000 m-1
For different working conditions, please consult our pre-sales department.
DCAT048-ID02 7
MVP
FEATURES
(1) = with an inlet pressure of 1 bar abs (14.5 psi) and

Technical data restrictions with fire resistant fluid viscosity between 15 and 35 cSt (77 and 163 SSU).
HFA - Oil emulsion in water (5 ÷ 15 % of oil)
Pump type MVP 30·28 30·34 48·45 48·53 60·60 60·72 60·84
p1 140 (2030)
Max. outlet
bar (psi) p2 150 (2175)
pressure pmax
p3 160 (2320)
Max. speed nmax min-1 @ Vmax (1) 2200 1800 2000 1700 2000 1700 1500
Seals N= Buna
Operating min. 2 (36)
°C (°F)
temperature max. 55 (131)
Bearing life
% 20 %
(ref. mineral oil)
HFB - Water emulsion in oil (40 % of water)
Pump type MVP 30·28 30·34 48·45 48·53 60·60 60·72 60·84
p1 160 (2320)
Max. outlet
bar (psi) p2 170 (2465)
pressure pmax
p3 180 (2610)
Max. speed nmax min -1
@ Vmax (1) 2350 1900 2150 1800 2150 1800 1600
Seals N= Buna
Operating min. 2 (36)
°C (°F)
Bearing life
% 40 %
(ref. mineral oil)
HFC - Water-glycol (35 ÷ 55 % of water)

05/10.2014
Pump type MVP 30·28 30·34 48·45 48·53 60·60 60·72 60·84
p1 180 (2610)
Max. outlet
bar (psi) p2 195 (2828)
pressure pmax
p3 210 (3045)
@ Vmax (1) 2350 1900 2150 1800 2150 1800 1600
Seals N= Buna
Operating min. -10 (14)
°C (°F)
Bearing life
% 40 %
(ref. mineral oil)
8 DCAT048-ID02
MVP
FEATURES
(1) = with an inlet pressure of 1 bar abs (14.5 psi) and

Technical data restrictions with fire resistant fluid viscosity between 15 and 35 cSt (77 and 163 SSU).
HFD - Phosphate ester
Pump type MVP 30·28 30·34 48·45 48·53 60·60 60·72 60·84
p1 200 (2900)
Max. outlet
bar (psi) p2 220 (3190)
pressure pmax
p3 240 (3480)
@ Vmax (1) 2350 1900 2150 1800 2150 1800 1600
Seals V= Viton
°C (°F)
Bearing life
% 90 %
(ref. mineral oil)
Technical data restrictions with biodegradable fluids
HETG - Natural based fluid (the water content must never exceed 0,1 %)
Pump type MVP 30·28 30·34 48·45 48·53 60·60 60·72 60·84
p1 180 (2610)
Max. outlet
bar (psi) p2 195 (2828)
pressure pmax
p3 210 (3045)
Seals N= Buna
°C (°F)
Bearing life
% 50 %
(ref. mineral oil)
HEPG - Polyglycol based synthetic fluid (the water content must never exceed 0,1 %)
Pump type MVP 30·28 30·34 48·45 48·53 60·60 60·72 60·84
p1 180 (2610)
Max. outlet
bar (psi) p2 195 (2828)
pressure pmax
p3 210 (3045)
Seals V= Viton
05/10.2014

°C (°F)
Bearing life
% 75 %
(ref. mineral oil)
HEES - Synthetic esters (the water content must never exceed 0,1 %)
Pump type MVP 30·28 30·34 48·45 48·53 60·60 60·72 60·84
Seals V= Viton
°C (°F)
Bearing life
% 100 %0
(ref. mineral oil)
DCAT048-ID02 9
MVP
FEATURES
Design calculations for pump
Q l/min (US gpm) Flow Q = Q theor. • ηv
M Nm (lbf in) Torque [l/min]

V (cm3/rev) • n (min-1)
Qtheor. =
P kW (HP) Power 1000
V cm3/rev (in3/rev) Displacement
M theor.
M =
n min-1 Speed ηhm
Δp bar (psi) Pressure [Nm]
Δp (bar) • V (cm3/rev)
ηv= ηv (V, Δp, n) Volumetric efficiency Mtheor.=
62,83
ηhm= ηhm (V, Δp, n) Hydro-mechanical efficiency
P OUT
ηt = ηv • ηhm Overall efficiency PIN =
ηt
[kW]
Δp (bar) • Q (l/min)
POUT =
600
Max. permissible load on drive shaft
MVP MVP MVP MVP MVP MVP MVP

Pump type
30•28 30•34 48•45 48•53 60•60 60•72 60•84
N 1000 1000 1500 1500 2000 2000 2000

Fax Axial force
(lbf) (225) (225) (337) (337) (450) (450) (450)
N 1500 1500 1500 1500 3000 3000 3000

Frad Radial force @ L/2
(lbf) (337) (337) (337) (337) (675) (675) (675)
% Variation of the max. speed in relation of the inlet pressure and/or displacement reduction
Inlet
Displacement %
pressure
psi (bar abs) 65 70 80 90 100
12 (0,8) 120 115 105 97 90
03/06.2011
13 (0,9) 120 120 110 103 95

of the max. speed
% Variation
14.5 (1,0) 120 120 115 107 100

17 (1,2) 120 120 120 113 106
20 (1,4) 120 120 120 120 112
23 (1,6) 120 120 120 120 117
29 (2,0) 120 120 120 120 120
Max. speed must not exceed the limits specified at page 7.
Example 1 Example 2
Displacement: 100 % Displacement: 80 %
Speed: 100 % Inlet pressure: 1,0 bar abs. (14.5 psi)
Inlet pressure: 1,0 bar abs. (14.5 psi) Speed: 115 %
10 DCAT048-ID02
MVP
FEATURES
Definition of rotation direction looking at the drive shaft
Anti-clockwise rotation
Side ports Rear ports
Clockwise rotation
Side ports Rear ports

03/06.2011
DCAT048-ID02 11
MVP
DISPLACEMENT SETTING
Max.displacement Max. displacement

limiter limiter

Min. displacement
limiter
 Special body without Min. displacement
E: Max. displacement limiter (Min displace- limiter is available only on request, please
ment limiter is plugged) consult our pre-sales department
G: Min. and Max. displacement limiter
Tightening torque 15±1 Nm (124 ÷ 142 lbf in)
MVP30 MVP48 MVP60
cm /rev
3 from 17,4 (1.06) 34,9 (2.13) 55 (3.36)
Max. displacement setting range (in3/rev) to 34,8 (2.12) 53,7 (3.28) 84,7 (5.17)
cm3/rev from 0 0 0
Min. displacement setting range (in3/rev) to 17,4 (1.06) 10,7 (0.65) 38,1 (2.32)
One turn of screw changes pump cm /rev
3 E 2,8 (0.17) 3,2 (0.20) 5,0 (0.31)
displacement by approximately (in3/rev) F 2,3 (0.14) 3,0 (0.18) 4,2 (0.26)
For different setting range, please consult our pre-sales department.
CENTER OF GRAVITY
Center of gravity
L CG1 • m1 + (L INT + L CG2) • m2

M MF = [Nm]
102
O 06/06.2020
MMF: Load moment on mounting flange

L CG : Distance from center of gravity to
L CG1 mounting flange [mm]
m: Weight (kg)
L INT L CG2
MVP30 MVP48 MVP60
L CG1 mm (in) 100 (3.94) 116 (4.57) 120 (4.72)
L CG2 mm (in) 90 (3.54) 99 (3.90) 107 (4.21)
L INT mm (in) 208 (8.19) 233 (9.17) 253 (9.96)
For single pumps refer to L CG2 values

Avarage data, for specific values please consult our pre-sales department.
12 DCAT048-ID02
MVP
MVP30•28 OPERATING CURVES
Each curve has been obtained at 50 °C (122 °F), using oil with viscosity 46 cSt (210 SSU) at 40 °C (104 °F) and at
these speed: (1) 1500 min-1
(2) 2000 min-1

(3) 3500 min-1
Delivery / power Noise level Distance from microphone to

@ max. displacement pump = 1 m (39.37 in)
@ max. displacement @ min. displacement
120 60 78
O
[dB(A)]
Q [l/min] - [(US gpm)]
P [kW] - [(HP)]
(31.7) (80.4)
75
100 50
(26.4) (3) (67.0)
72
80 40
(21.1) (53.6) 69
(2)
60 30 66
(15.9) (2) (40.2)
(1)
(1) 63
40 20
(10.6) (26.8)
60
(3) (2)
20 10 (2)
(5.3) (1) (13.4) 57
(1)
0 0 54
0 50 100 150 200 250 300 0 50 100 150 200 250 300
(725) (1450) (2175) (2900) (3625) (4350) (725) (1450) (2175) (2900) (3625) (4350)
p [bar] - [(psi)] p [bar] - [(psi)]
Volumetric efficiency Overall efficiency

@ max. displacement @ max. displacement
280 280
p [bar] - [(psi)]
p [bar] - [(psi)]
(4060) (4060)
250 250
(3625) (3625)
200 200
(2900) (2900)
O 06/06.2020
150 150
(2175) (2175)
100 100
(1450) (1450)
50 50
(725) (725)
1000 1500 2000 2500 3000 3500 1000 1500 2000 2500 3000 3500
n [min-1] n [min-1]
Values shown in the diagrams are indicative only. Actual values may vary depending on the pump configuration.
DCAT048-ID02 13
MVP
(2) 2000 min-1

(3) 2900 min-1
120 60 78
O
[dB(A)]
P [kW] - [(HP)]
(31.7) (80.4)
75
100 (3) 50
(26.4) (67.0)
72
80 40
(21.1) (53.6) 69 (2)
(2)
60 30 66
(15.9)
(1) (40.2) (1)
63
40 20
(10.6) (2) (26.8)
(3)
60
(1)
20 10 (2)
(5.3) (13.4) 57
(1)
0 0 54
0 50 100 150 200 250 300 0 50 100 150 200 250 300
(725) (1450) (2175) (2900) (3625) (4350) (725) (1450) (2175) (2900) (3625) (4350)

250 250
p [bar] - [(psi)]
p [bar] - [(psi)]
(3625) (3625)
200 200
(2900) (2900)
O 06/06.2020
150 150
(2175) (2175)
100 100
(1450) (1450)
50 50
(725) (725)
1000 1500 2000 2500 2900 1000 1500 2000 2500 2900
n [min-1] n [min-1]
14 DCAT048-ID02
MVP

(2) 2000 min-1

(3) 3000 min-1

160 80 78
O
[dB(A)]
P [kW] - [(HP)]
(42.3) (107.2)
140 70
(37.0) (3) (93.8) 75
120 60
(31.7) (80.4) 72
(2)
100 50
(26.4) (67.0)
(2) 69
(1)
80 40
(21.1) (53.6)
(1) 66
60 30
(15.9) (40.2)
(2)
(3)
63
40 20
(10.6) (26.8)
(2)
20 (1) 10 60
(5.3) (13.4)
(1)
0 0 57
0 50 100 150 200 250 300 0 50 100 150 200 250 300
(725) (1450) (2175) (2900) (3625) (4350) (725) (1450) (2175) (2900) (3625) (4350)

280 280
p [bar] - [(psi)]
p [bar] - [(psi)]
(4060) (4060)
250 250
(3625) (3625)
200 200
(2900) (2900)
O 06/06.2020
150 150
(2175) (2175)
100 100
(1450) (1450)
50 50
(725) (725)
1000 1500 2000 2500 3000 1000 1500 2000 2500 3000
n [min-1] n [min-1]
DCAT048-ID02 15
MVP
(2) 2000 min-1

(3) 2500 min-1
160 80 78
O
[dB(A)]
P [kW] - [(HP)]
(42.3) (107.2)
140 70
(37.0) (3) (93.8) 75
120 60 (2)
(31.7) (80.4) 72
(2)
100 50
(26.4) (67.0)
69 (1)
80 (1) 40
(21.1) (53.6)
66
60 30
(2)
(15.9) (40.2)
40 (3) 20
63
(10.6) (26.8)
(1) (2)
20 10 60
(5.3) (13.4)
(1)
0 0 57
0 50 100 150 200 250 300 0 50 100 150 200 250 300
(725) (1450) (2175) (2900) (3625) (4350) (725) (1450) (2175) (2900) (3625) (4350)

250 250
p [bar] - [(psi)]
p [bar] - [(psi)]
(3625) (3625)
200 200
(2900) (2900)
O 06/06.2020
150 150
(2175) (2175)
100 100
(1450) (1450)
50 50
(725) (725)
1000 1500 2000 2500 1000 1500 2000 2500
n [min-1] n [min-1]
16 DCAT048-ID02
MVP

(2) 2000 min-1

(3) 3000 min-1

200 100 81
O
[dB(A)]
P [kW] - [(HP)]
(52.8) (134.0)
(3)
78
160 80
(42.3) (107.2)
75
(2)
120 (2) 60
(31.7) (80.4) 72
(1)
(1)
80 40 69
(21.1) (53.6)
(2)
(3)
66
40 20
(10.6)
(1) (26.8) (2)
63
(1)
0 0 60
0 50 100 150 200 250 300 0 50 100 150 200 250 300
(725) (1450) (2175) (2900) (3625) (4350) (725) (1450) (2175) (2900) (3625) (4350)

280 280
p [bar] - [(psi)]
p [bar] - [(psi)]
(4060) (4060)
250 250
(3625) (3625)
200 200
(2900) (2900)
O 06/06.2020
150 150
(2175) (2175)
100 100
(1450) (1450)
50 50
(725) (725)
1000 1500 2000 2500 3000 1000 1500 2000 2500 3000
n [min-1] n [min-1]
DCAT048-ID02 17
MVP
(2) 2000 min-1

(3) 2700 min-1
175 105 81
O
[dB(A)]
P [kW] - [(HP)]
(46.2) (140.7)
(3)
150 90 78
(39.6) (2) (120.6)
125 75 75
(33.0) (100.5) (2)
(1)
100 60 72
(26.4) (80.4) (1)
75 45
(2)
69
(19.8) (60.3)
(3)
50 30 66
(13.2) (40.2)
(1) (2)
25 15 63
(6.6) (20.1)
(1)
0 0 60
0 50 100 150 200 250 300 0 50 100 150 200 250 300
(725) (1450) (2175) (2900) (3625) (4350) (725) (1450) (2175) (2900) (3625) (4350)

280 280
p [bar] - [(psi)]
p [bar] - [(psi)]
(4060) (4060)
250 250
(3625) (3625)
200 200
(2900) (2900)
O 06/06.2020
150 150
(2175) (2175)
100 100
(1450) (1450)
50 50
(725) (725)
1000 1500 2000 2500 2700 1000 1500 2000 2500 2700
n [min-1] n [min-1]
18 DCAT048-ID02
MVP

(2) 2000 min-1

(3) 2300 min-1 O

200 100 81
O
[dB(A)]
P [kW] - [(HP)]
(52.8) (134.0)
(3)
78
160 80
(42.3) (2) (107.2)
(2)
75
(1)
120 60 (1)
(31.7) (80.4) 72
(2)
80 40 69
(21.1) (53.6)
(3)
66
40 (1) 20
(10.6) (26.8) (2)
63
(1)
0 0 60
0 50 100 150 200 250 300 0 50 100 150 200 250 300
(725) (1450) (2175) (2900) (3625) (4350) (725) (1450) (2175) (2900) (3625) (4350)

250 250
p [bar] - [(psi)]
(3625)
p [bar] - [(psi)]
(3625)
200 200
(2900) (2900)
O 06/06.2020
150 150
(2175) (2175)
100 100
(1450) (1450)
50 50
(725) (725)
1000 1500 2000 2300 1000 1500 2000 2300
-1
n [min ] n [min-1]
DCAT048-ID02 19
MVP
MVP30 SIDE PORTS - DIMENSIONS L

Drive shafts: see page 32
Mounting flanges: see page 36
Ports: see page 38 ÷ 40
IN OUT
D1
O 06/06.2020
20 DCAT048-ID02
MVP
MVP30 REAR PORTS - DIMENSIONS P

O
IN OUT
D1
OUT IN
O 06/06.2020
DCAT048-ID02 21
MVP
MVP30/KP20 MULTIPLE PUMPS - DIMENSIONS L

Common inlet intermediate flange: Drive shafts: see page 32
MVP code P7 Mounting flanges: see page 36
KP20 code N5 Ports: see page 38 ÷ 40
IN
D1
110 Nm
974 lbf in
O 06/06.2020
OUT
O Gear pump KAPPA 20 (for more information please consult our pre-sales department)
Pump
type
4 6,3 8 11,2 14 16 20 Dimensions
247,5 250 252,5 256 260 265,5 272 mm

A
(9.74) (9.84) (9.94) (10.08) (10.24) (10.45) (10.71) (in)
MVP30
218,5 221 223,5 227 225,5 231 237,5 mm
B
(8.60) (8.70) (8.80) (8.94) (8.86) (9.09) (9.35) (in)
22 DCAT048-ID02
MVP
MVP30/PHP20 MULTIPLE PUMPS - DIMENSIONS L

Common inlet intermediate flange: Drive shafts: see page 32 Also available in
MVP code I7 Mounting flanges: see page 36 combination with PLP20
PHP20 code S7 Ports: see page 38 ÷ 40
O
IN
D1
110 Nm
974 lbf in
O 06/06.2020
OUT
O Gear pump POLARIS PH20 (for more information please consult our pre-sales department)
Pump Dimen-
type
8 10,5 11,2 14 16 18 19 20 23 24,5 25 27,8 31,5 sions
274,6 278,6 279,1 284,1 287,6 289,8 291 294,1 297,6 299,9 301,6 304,4 311,6 mm
(10.81) (10.97) (10.99) (11.41) (11.32) (11.41) (11.46) (11.58) (11.72) (11.81) (11.87) (11.98) (12.27) (in)
A
MVP30
228 231 231,5 236,5 239,5 230,4 231 232,5 234,2 235,3 236,5 237,9 241,5 mm
(8.98) (9.09) (9.11) (9.31) (9.43) (9.07) (9.09) (9.15) (9.22) (9.26) (9.31) (9.36) (9.51) (in)
B
DCAT048-ID02 23
MVP

IN OUT
D1
O 06/06.2020
24 DCAT048-ID02
MVP

O
IN OUT
D1
OUT IN
O 06/06.2020
DCAT048-ID02 25
MVP

Common inlet intermediate flange: Drive shafts: see page 33
MVP code P7 Mounting flanges: see page 36
IN
D1
110 Nm
974 lbf in
O 06/06.2020
OUT
Gear pump KAPPA 20 (for more information please consult our pre-sales department)
Pump
type
4 6,3 8 11,2 14 16 20 Dimensions
263 265,5 268 271,5 275,5 281 287,5 mm

A
(10.35) (10.45) (10.55) (10.69) (10.85) (11.06) (11.32) (in)
MVP48
234 236,5 239 242,5 241 246,5 253 mm
B
(9.21) (9.31) (9.41) (9.55) (9.49) (9.70) (9.96) (in)
26 DCAT048-ID02
MVP

Common inlet intermediate flange: Drive shafts: see page 33 Also available in
MVP code I7 Mounting flanges: see page 36 combination with PLP20
O
IN
D1
110 Nm
974 lbf in
O 06/06.2020
OUT
Gear pump POLARIS PH20 (for more information please consult our pre-sales department)
Pump Dimen-
type
8 10,5 11,2 14 16 18 19 20 23 24,5 25 27,8 31,5 sions
290,1 294,1 294,6 299,6 303,1 305,3 306,5 309,6 313,1 315,4 317,1 319,9 327,1 mm
(11.42) (11.58) (11.60) (11.80) (11.93) (12.02) (12.07) (12.19) (12.33) (12.42) (12.48) (12.59) (12.88) (in)
A
MVP48
243,5 246,5 247 252 255 245,9 246,5 248 249,7 250,8 252 253,4 257 mm
(9.59) (9.70) (9.72) (9.92) (10.04) (9.68) (9.70) (9.76) (9.83) (9.87) (9.92) (9.97) (10.12) (in)
B
DCAT048-ID02 27
MVP

Drive shafts: see page 34 ÷ 35
Mounting flanges: see page 36 ÷ 37
IN OUT
D1
O 06/06.2020
28 DCAT048-ID02
MVP

Drive shafts: see page 34 ÷ 35
Mounting flanges: see page 36 ÷ 37
O
IN OUT
D1
OUT IN
O 06/06.2020
DCAT048-ID02 29
MVP

Common inlet intermediate flange: Drive shafts: see page 34 ÷ 35
MVP code P7 Mounting flanges: see page 36 ÷ 37
IN
D1
110 Nm
974 lbf in
O 06/06.2020
OUT
Gear pump KAPPA 20 (for more information please consult our pre-sales department)
Pump
type
4 6,3 8 11,2 14 16 20 Dimensions
301,3 303,8 306,3 309,8 313,8 319,3 325,8 mm

A
(11.86) (11.96) (12.06) (12.20) (12.35) (12.57) (12.83) (in)
MVP60
272,3 274,8 277,3 280,8 279,3 284,8 291,3 mm
B
(10.72) (10.82) (10.92) (11.06) (11.00) (11.21) (11.47) (in)
30 DCAT048-ID02
MVP

Common inlet intermediate flange: Drive shafts: see page 34 ÷ 35 Also available in
MVP code I7 Mounting flanges: see page 36 ÷ 37 combination with PLP20
O
IN
D1
110 Nm
974 lbf in
O 06/06.2020
OUT
O Gear pump POLARIS PH20 (for more information please consult our pre-sales department)
Pump Dimen-
type
8 10,5 11,2 14 16 18 19 20 23 24,5 25 27,8 31,5 sions
328,4 332,4 332,9 337,9 341,4 343,6 344,8 347,9 351,4 353,7 355,4 358,2 365,4 mm
(12.93) (13.09) (13.11) (13.30) (13.44) (13,53) (13.57) (13.70) (13.83) (13.93) (13.99) (14.10) (14.39) (in)
A
MVP60
281,8 284,8 285,3 290,3 293,3 284,2 284,8 286,3 288 289,1 290,3 291,7 295,3 mm
(11.09) (11.21) (11.23) (11.43) (11.55) (11.19) (11.21) (11.27) (11.34) (11.38) (11.43) (11.48) (11.63) (in)
B
DCAT048-ID02 31
MVP
MVP30 DRIVE SHAFTS
SAE “A” SPLINE 03 SAE SPLINE 07

Mounting face refers to flange code S1 Mounting face refers to flange code S1
O O
110 Nm Ext. Involute Spline SAE J498B 170 Nm Ext. Involute Spline ANSI B92.1
973 lbf in with major diameter modified 1505 lbf in with major diameter modified
9 teeth - 16/32 Pitch - 30 deg 11 teeth - 16/32 Pitch - 30 deg
Flat root - Side fit - Class 1 Flat root - Side fit - Class 5
SAE “B” SPLINE 04 SAE “B” SPLINE 4R

Mounting face refers to flange code S5
270 Nm 290 Nm
2389 lbf in 2566 lbf in
Ext. Involute Spline ANSI B92.1 Ext. Involute Spline ANSI B92.1
with major diameter modified with major diameter modified
13 teeth - 16/32 Pitch - 30 deg 13 teeth - 16/32 Pitch - 30 deg
SAE “B” STRAIGHT 32

O 06/06.2020
210 Nm
1858 lbf in
For different drive shafts, please consult our pre-sales department.
32 DCAT048-ID02
MVP
MVP48 DRIVE SHAFTS
SAE “B” SPLINE 04 SAE “B” SPLINE 4R

270 Nm Ext. Involute Spline ANSI B92.1 290 Nm

2389 lbf in with major diameter modified 2566 lbf in
13 teeth - 16/32 Pitch - 30 deg
Flat root - Side fit - Class 5
Ext. Involute Spline ANSI B92.1
with major diameter modified
SAE “BB” SPLINE 05 SAE “BB” SPLINE 5R

440 Nm 460 Nm
Ext. Involute Spline ANSI B92.1
with major diameter modified Ext. Involute Spline ANSI B92.1
15 teeth - 16/32 Pitch - 30 deg with major diameter modified
Flat root - Side fit - Class 5 15 teeth - 16/32 Pitch - 30 deg

05/10.2014
210 Nm
1858 lbf in
For different drive shafts, please consult our pre-sales
department.
DCAT048-ID02 33
MVP
MVP60 DRIVE SHAFTS
SAE “B” SPLINE 04

O
270 Nm Ext. Involute Spline ANSI B92.1
2389 lbf in with major diameter modified
SAE “BB” SPLINE 05 SAE “BB” SPLINE 5R

440 Nm 440 Nm
Ext. Involute Spline ANSI B92.1 Ext. Involute Spline ANSI B92.1
with major diameter modified with major diameter modified
15 teeth - 16/32 Pitch - 30 deg O 15 teeth - 16/32 Pitch - 30 deg
SAE “C” SPLINE 06 SAE “C” SPLINE 6R

Mounting face refers to flange code S7 and S8 Mounting face refers to flange code S7 and S8
O 06/06.2020
810 Nm 880 Nm
34 DCAT048-ID02
MVP
MVP60 DRIVE SHAFTS
SAE “C” STRAIGHT 34

810 Nm
7169 lbf in
O
O 06/06.2020
DCAT048-ID02 35
MVP
MOUNTING FLANGES AND TABLE OF COMPATIBILITY
SAE “A” 2 HOLES S1 SAE “B” 2 HOLES S5

Conforms to SAE J744 Conforms to SAE J744
O
DRIVE SHAFTS DRIVE SHAFTS
See page 32 O See page 32 ÷ 35
Pump Pump
type
03 07 04 type
04 4R 32 05 5R 06 6R 34
MVP30 x x x MVP30 x x x
O 06/06.2020
X Available combination MVP48 x x x x x

MVP60 x x x x x x
X Available combination
36 DCAT048-ID02
MVP
MOUNTING FLANGES AND TABLE OF COMPATIBILITY
SAE “C” 2 HOLES S7 SAE “C” 4 HOLES S8

Conforms to SAE J744 Conforms to SAE J744
DRIVE SHAFTS DRIVE SHAFTS

O See page 34 ÷ 35 O See page 34 ÷ 35
Pump Pump
type
04 05 5R 06 6R 34 type
04 05 5R 06 6R 34
MVP60 x x x x x x MVP60 x x x x x x
O 06/06.2020
X Available combination X Available combination
DCAT048-ID02 37
MVP
PORTS TYPE
LOAD SENSING KP20 / PHP20

O INLET / OUTLET PORTS DRAIN PORTS
PORTS (X) GEAR PUMPS
Split Split SAE Gas SAE Gas SAE Gas SAE
Ports type SSM SSS ODT BSPP ODT (l) BSPP (l) ODT BSPP ODT
IN OUT IN OUT IN OUT D1 - D2 - D3 - D4 X X OUT OUT
MVP30 MD MB SD SB OG (n) OD (n) — OB GA 03 GD OC
MVP48 ME MC SE SC OH (n) OF (n) GD OC GA 03 GD OC
MVP60 MF MC SF SC MF OF GD OC GA 03 GD OC
(X) Load sensing port. For more information please consult our pre-sales department.
(l) Standard.
(n) Only for rear ports.
DRAIN PORTS POSITION
D1
D2
D4 D3
O 06/06.2020
Pump A B C D
type mm (in) mm (in) mm (in) mm (in)
MVP30 28,5 (1.12) 87,5 (3.44) 87,5 (3.44) 87,5 (3.44)
MVP48 36 (1.42) 97 (3.82) — 97 (3.82)
MVP60 37 (1.46) 113 (4.45) 99 (3.90) 99 (3.90)
38 DCAT048-ID02
MVP
PORTS SIZES
Tightening torque for low pressure side port
Tightening torque for high pressure side port
SAE FLANGED PORTS J518 - Standard pressure series 3000 psi - Code 61 SSM
Metric thread ISO 60° conforms to ISO/R 262
Nominal
A B C D
CODE
size mm mm mm Thread Nm Nm
(in) (in) (in) Depth mm (in) (lbf in) (lbf in)
20 47,6 22,2 M 10 45 +2,5
MB 3/4”
(0.79) (1.87) (0.87) 17 (0.67)
—
(398 ÷ 420)
25,4 52,4 26,2 M 10 30 +2,5
MC 1”
(1.00) (2.06) (1.03) 17 (0.67)
—
(266 ÷ 288)
32 58,7 30,2 M 10 20 +1
MD 1” 1/4
(1.26) (2.31) (1.19) 17 (0.67) (177 ÷ 186)
—
38,1 69,8 35,7 M 12 30 +2,5

ME 1” 1/2
(1.50) (2.75) (1.41) 20 (0.79) (266 ÷ 288)
—
51 77,8 42,9 M 12 30 +2,5

MF 2”
(2.01) (3.06) (1.69) 20 (0.79) (266 ÷ 288)
—
SAE FLANGED PORTS J518 - Standard pressure series 3000 psi - Code 61 SSS
American straight thread UNC-UNF 60° conforms to ANSI B 1.1
Nominal
A B C D
CODE
size mm mm mm Thread Nm Nm
(in) (in) (in) Depth mm (in) (lbf in) (lbf in)
20 47,6 22,2 3/8 - 16 UNC-2B 30 +2,5
SB 3/4”
(0.79) (1.87) (0.87) 17 (0.67)
—
(266 ÷ 288)
03/06.2011
25,4 52,4 26,2 3/8 - 16 UNC-2B 35 +2,5

SC 1”
(1.00) (2.06) (1.03) 17 (0.67)
—
(310 ÷ 332)
32 58,7 30,2 7/16 - 14 UNC-2B 25 +1
SD 1” 1/4
(1.26) (2.31) (1.19) 17 (0.67) (221 ÷ 230)
—
38,1 69,8 35,7 1/2 - 13 UNC-2B 30 +2,5

SE 1” 1/2
(1.50) (2.75) (1.41) 20 (0.79) (266 ÷ 288)
—
51 77,8 42,9 1/2 - 13 UNC-2B 30 +2,5

SF 2”
(2.01) (3.06) (1.69) 20 (0.79) (266 ÷ 288)
—
DCAT048-ID02 39
MVP
PORTS SIZES
Tightening torque for low pressure side port
Tightening torque for high pressure side port
SAE STRAIGHT THREAD PORTS J514 ODT
American straight thread UNC-UNF 60° conforms to ANSI B 1.1
Nominal
A ØB ØC D E
CODE
size mm mm mm mm mm Nm Nm
(in) (in) (in) (in) (in) (lbf in) (lbf in)
9,5 12 +1
03 (X) 1/4” 7/16” - 20 UNF - 2B —
(0.37)
— — —
(106 ÷ 115)
33 17 1 20 +1
OB (l) 1/2” 3/4” - 16 UNF - 2B
(1.30) (0.67)
—
(0.04) (177 ÷ 186)
—
35 20,5 2 30 +2,5
OC (l) (1.38) (0.81)
—
(0.08) (266 ÷ 288)
—
5/8” 7/8” - 14 UNF - 2B
34 20,5 17 0,5 70 +5
OC (u) (1.34) (0.81) (0.67) (0.02)
—
(620 ÷ 664)
20 120 +10
OD 3/4” 1 1/16” - 12 UNF - 2B — —
(0.79)
— —
(1062 ÷ 1151) O
30,5 20 170 +10
OF 1” 1 5/16” - 12 UNF - 2B —
(1.20) (0.79)
— —
(1505 ÷ 1593)
20 70 +5
OG 1” 1/4 1 5/8” - 12 UNF - 2B — —
(0.79)
—
(620 ÷ 664)
— O
45 20 100 +5
OH 1” 1/2 1 7/8” - 12 UNF - 2B —
(1.77) (0.79)
—
(885 ÷ 929)
—
(X) = Load sensing port - (l) = Drain port - (u) = KP20 / PHP20 outlet port
GAS STRAIGHT THREAD PORTS BSPP

British standard pipe parallel (55°) conforms to UNI - ISO 228
O 06/06.2020
Nominal
A ØB ØC D E
CODE
size mm mm mm mm mm Nm Nm
(in) (in) (in) (in) (in) (lbf in) (lbf in)
8,75 12 5 +0,25
GA (X) 1/8” G 1/8 —
(0.34) (0.47)
— —
(44 ÷ 46)
30 19 17 2 20 +1
GD (l) (1.18) (0.75) (0.67) (0.08) (177 ÷ 186)
—
1/2” G 1/2
19 17 50 +2,5
GD (u) —
(0.75) (0.67)
— —
(443 ÷ 465)
(X) = Load sensing port - (l) = Drain port - (u) = KP20 / PHP20 outlet port
40 DCAT048-ID02
MVP
PRESSURE COMPENSATOR RP0
Regulates the pump displacement automatically to mantain

the pressure below the fixed pre-adjusted limit.
Pressure setting Standard

Compensator Pump range setting
type type
bar (psi) bar (psi)
80 ÷ 280 280
MVP30·28 (1160 ÷ 4060) (4060)
80 ÷ 250 250
MVP30·34 (1160 ÷ 3625) (3625)
80 ÷ 280 280
MVP48·45 (1160 ÷ 4060) (4060)
80 ÷ 250 250
RP0 MVP48·53 (1160 ÷ 3625) (3625)
80 ÷ 280 280 Z Option
MVP60·60 (1160 ÷ 4060) (4060)
80 ÷ 280 280
MVP60·72 (1160 ÷ 4060) (4060)
MVP60·84
80 ÷ 250 250 Z OPTION
(1160 ÷ 3625) (3625) Damping restrictor for critical applications.
In case of system instability or pressure oscillations, the
NOTES additional damping restrictor slows down the pump control
For more information, please consult our pre-sales depart- system, damping the regulation transients.
ment. The pump recovery time increases.
The use of the damping restrictor must be evaluated and
OPERATING CURVES approved by Casappa technical sales department for the
Curves have been obtained at the speed of 1500 min-1 and oil specific application.
temperature 50 °C (122 °F).
Max. 4 bar
(58 psi)
REMOTE CONTROL
For remote pressure compensator LS3 see page 46.
0
0 280
(4060)
p [bar] - [(psi)]
05/10.2014
RESPONSE AND RECOVERY TIME

According to SAE J745 (using outlet pressure).
t1 t2
Pressure
Pump Response time [ms] Recovery time [ms]

type (off stroke) (on stroke)
MVP30 46 150
MVP48 48 150
MVP60 50 150
t1 t2
t [m s ]
DCAT048-ID02 41
MVP
PRESSURE COMPENSATOR RP1

RP1
the pressure below the fixed pre-adjusted limit.
Designed to work at high frequency ≥ 2 cycle/min and/or at
pressure > 280 bar (4060 psi). X
NOTES
X: Load-sensing port. Dimensions at page 38 ÷ 40.
For more information, please consult our pre-sales depart-
ment.
OPERATING CURVES
Curves have been obtained at the speed of 1500 min-1 and oil Z Option
temperature 50 °C (122 °F). (See page 41 for more information)
Max. 4 bar
(58 psi) RP1 - LS2 (with flow control)
Not included
in supply
0
0 280
(4060)
p [bar] - [(psi)]
05/10.2014
Z Option
(See page 41 for more information)
42 DCAT048-ID02
MVP
DUAL SETTING PRESSURE COMPENSATOR RP2

RP2
the pressure below two fixed pre-adjusted limits.
The electrically piloted valve allows to switch between the
two different limits.
NOTES
Connector: Standard type DIN 43650.
For other connectors and more information please consult
our pre-sales department.
OPERATING CURVES
Curves have been obtained at the speed of 1500 min-1 and oil
temperature 50 °C (122 °F).
Z Option
Max. 4 bar
(58 psi) RP2 - LS2 (with flow control)
Not included
in supply
0
0 280
(4060)
p [bar] - [(psi)]
VALVE FEATURES O
Valve
Arrangement Voltage
code
1
O 06/06.2020
Normally closed 12 V DC
2 Normally closed 24 V DC
Z Option
6 Normally open 12 V DC
DCAT048-ID02 43
MVP
ELECTRO-PROPORTIONAL PRESSURE COMPENSATOR PEC
Regulates the pump displacement automatically to mantain PEC

the pressure below the variable limit set through a command
current signal. X
NOTES
For more information please consult our pre-sales department.
OPERATING CURVES
Z Option
Pressure
pA
Normally Normally
PEC - LS2 (with flow control)
closed open
Not included
in supply
pB
I / Imax
X
VALVE FEATURES
Valve code Arrangement Voltage

O 06/06.2020
O
Connector type DIN 43650/ DEUTSCH DT04-2P
Z Option
Voltage 12 V DC 24 V DC 12 V DC 24 V DC
Power 18 W 19 W 18 W 19 W
Resistance
8Ω 30 Ω 8Ω 30 Ω
@ 20 °C (68 °F)
Limit current 1500 mA 800 mA 1500 mA 800 mA
Dither frequency 200 Hz
Operating -40 ÷ 100 °C
temperature (-40 ÷ 212 °F)
44 DCAT048-ID02
MVP
ELECTRO-PROPORTIONAL PRESSURE COMPENSATOR PLUS ANGULAR SENSOR PECA
Regulates the pump displacement automatically to mantain PECA

the pressure below the variable limit set through a com-
mand current signal. The swivel angular sensor converts the X
actual position of the swashplate into a voltage output signal
that can be used for different purposes. This signal and the
proportional relief valve allow to realise the following different
control logics by means of an external control unit:
• Variable maximum pressure limiter

• Electronic flow compensator with
variable setting (variable Load-Sensing)
• Electronic torque limiter with variable torque setting
• Power limiter
• Flow control
• Working e-modes
NOTES
Not available with MVP30.
For more information please consult our pre-sales department. Z Option
OPERATING CURVES
PECA - LS2 (with flow control)
Pressure
pA Not included
in supply
Normally Normally X
closed open
pB
I / Imax
VALVE FEATURES
Valve code Arrangement Voltatge

Z Option
O 06/06.2020
O ANGULAR SENSOR
Connector type DIN 43650 DEUTSCH DT04-2P 5
Sensor ouput signal [V]
4
Power W 18 W 19 W 18 W 19 W
Resistance
8Ω 30 Ω 8Ω 30 Ω 3
@ 20 °C (68 °F)
2
Dither frequency 200 Hz
DIAG056-001
Operating -40 ÷ 100 °C 1

temperature (-40 ÷ 212 °F)
Angular sensor 0
DEUTSCH DTM04-4P 0 25 50 75 100
connector type
Pump displacement [%]
DCAT048-ID02 45
MVP
FLOW COMPENSATOR (Load-sensing) LS
Regulates the pump displacement to maintain a constant LS0 (Bleed open) - LS2 (Bleed closed)
(load independent) pressure drop across a flow metering
device. In the standard version the flow compensator is com- Not included
bined with pressure compensator. in supply
X
Differential
Flow Standard
Pressure pressure
compensator setting
compensator setting range
type
bar (psi) bar (psi)
LS0 (n) RPO
12 ÷ 40 14
LS2 (u) RPO (174 ÷ 580) (203)
LS3 (l) RPO
(n): Suggested when the directional control valve does not have
the bleed function
(u): Y is plugged. Suggested when the directional control valve
has the bleed function Y
(l): For remote pressure control.
Z Option
Pilot flow ≈ 1,3 ÷ 1,5 l/min (0.34 ÷ 0.40 US gpm)
In standard setting conditions 14 bar (203 psi) the stand-by
LS3 - Remote pressure compensator
pressure is 15±2 bar (218±29 psi).
NOTES X
Available without pressure compensator RP.
For more information please consult our pre-sales depart-
ment.
OPERATING CURVES
Curves have been obtained at the speed of 1500 min-1 and oil Not included
temperature 50 °C (122 °F). in supply
Curve at variable speed

ΔQ
Z Option
ΔQ max
05/10.2014
0
-1
0 n [min ] Pump type l/min (US gpm)
RESPONSE TIME MVP 30 0,9 (0.24)

According to SAE J745 (using outlet pressure). MVP 48 1,7 (0.45)
MVP 60 2,5 (0.66)
Pressure
t1
Pump Response time [ms]
type (off stroke)
MVP 30 120
t1 MVP 48 120
MVP 60 120
t [ms] According to SAE J745 (using outlet pressure)
46 DCAT048-ID02
MVP
TORQUE LIMITER RN
Regulates the pump displacement according to the system

RN0 - Standard
pressure, to maintain the pre-adjusted torque value and pro-
tect the prime mover from overload. To have the best torque Torque limitation for closed center valve.
limiter regulation, the pre-adjusted absorbed torque has to be
higher than the value shown in the following table. Not included
in supply
Pump Min. torque Min. power (l)

type Nm (lbf in) kW (HP)
MVP30 45 (398) 7.1 (9,5)
MVP48 61 (540) 9.6 (12,9)
MVP60 97 (859) 15.2 (20,4)
(l) @ 1500 min -1
For lower torque setting values, the regulator limits the maxi-
mum working pressure to a value lower than the standard
setting for the pressure regulator 280 bar (4060 psi).
When ordering the torque limiter please specify the requested
value of torque [eg. 70 Nm (620 lbf in)] or the requested Z Option
power and speed [eg. 10 kW (13.4 HP) at 1500 min-1].
RN1 - Internal pilot

NOTES Torque limitation for open center valve.
X
ment.
OPERATING CURVES
100
% Q [l/min] - [(US gpm)]
75
Theoretical
05/10.2014
power
Z Option
50
25
0
0
p [bar] - [(psi)]
DCAT048-ID02 47
MVP
DUAL SETTING TORQUE LIMITER RN2

RN2-LS0 / RN2-LS2
the torque below two fixed pre-adjusted limits.
The electrically piloted valve allows to switch between the For LS2 configuration Y is plugged.
two different limits.
Not included
in supply

MVP30 45 (398) 7.1 (9,5)
MVP48 61 (540) 9.6 (12,9)
MVP60 97 (859) 15.2 (20,4)
(l) @ 1500 min -1
For lower torque setting values, the regulator limits the maxi-
mum working pressure to a value lower than the standard Y
Z Option
When ordering the torque limiter please specify the requested (See page 41 for more information)
value of torque [eg. 70 Nm (620 lbf in)] or the requested
NOTES
ment.
VALVE FEATURES
Valve
Arrangement Voltage
OPERATING CURVES code
100 2 Normally closed 24 V DC

75 Theoretical
power
05/10.2014
DIN 43650
Connector type
DEUTSCH DT04-2P
50
25
0
0
p [bar] - [(psi)]
48 DCAT048-ID02
MVP
HIGH PERFORMANCE TORQUE LIMITER RN3
Regulates the pump displacement according to the system

RN3 - Special version
pressure, to maintain the pre-adjusted torque value and pro-
tect the prime mover from overload.
This version is optimized for LS systems. With the standard
torque limiter RN0, in case of a high flow through the LS main Not included
valve the torque absorbed by the pump can be slightly lower in supply
than the pre-adjusted torque value, resulting in a lower flow. X
The RN3 version grants the pre-adjusted torque value even at
high flow through the LS main valve.
To have the best torque limiter regulation, the pre-adjusted
absorbed torque has to be higher than the value shown in the
following table.

MVP30 45 (398) 7.1 (9,5)
MVP48 61 (540) 9.6 (12,9)
MVP60 97 (859) 15.2 (20,4)
(l) @ 1500 min -1
Z Option
For lower torque setting values, the regulator limits the maxi- (See page 41 for more information)
mum working pressure to a value lower than the standard
When ordering the torque limiter please specify the requested
value of torque [eg. 70 Nm (620 lbf in)] or the requested
NOTES
Available with or without pressure compensator RP.
ment.
OPERATING CURVES
100
O 06/06.2020
75
Theoretical
power
50
25
0
0
p [bar] - [(psi)]
DCAT048-ID02 49
MVP
UNLOADING VALVE U ..
NC (normally closed) NA (normally open)
Z Option Z Option
(See page 41 for more information) (See page 41 for more information)
With the valve NC type (normally closed), energizing the With the valve NA type (normally open), energizing the sole-
olenoid valve the displacement is reset and the pump is noid valve the pump works at the maximum displacement.
unloaded.
NOTES
Connector type: DIN 43650.
For other connectors and more information please consult
our pre-sales department.
VALVE FEATURES O
Valve
Arrangement Voltage
code
U1 Normally closed 12 V DC
U2 Normally closed 24 V DC
O 06/06.2020
U6 Normally open 12 V DC
U7 Normally open 24 V DC
50 DCAT048-ID02
MVP
ELECTRO-PROPORTIONAL DISPLACEMENT COMPENSATOR DEC
Regulates the pump displacement automatically to maintain

DEC
it below the variable limit set through a command current
signal.
OPERATING CURVES
Displacement
DMAX
Inverse Direct
DMIN
I / Imax
VALVE FEATURES
Valve
Arrangement Voltage
code
1 Inverse 12 V DC
2 Inverse 24 V DC
6 Direct 12 V DC
7 Direct 24 V DC
Connector type DIN 43 650 DEUTSCH DT04-2P

Power 33 W 33 W
Resistance @ 20 °C (68 °F) 4,4 Ω 17,4 Ω 4,3 Ω 17,5 Ω
Dither frequency 150 Hz 150 Hz
Operating temperature -40 ÷ 100 °C (-40 ÷ 212 °F) -40 ÷ 100 °C (-40 ÷ 212 °F)
O 06/06.2020
DCAT048-ID02 51
MVP
NOTES
06/06.2020
52 DCAT048-ID02
MVP
MULTIPLE PUMPS WITH THROUGH DRIVE
THROUGH DRIVE
MVP through drive axial piston pumps offer the flexibility to obtain different groups able to supply several hydraulic systems.
The operating characteristics of each assembled pumps are the same as the corresponding single pumps according to the
following conditions:
1) Do not exceed the maximum transmissible torque.

2) The maximum rotational speed is that of the lowest rated speed of the single unit incorporated.
M Nm (lbf in) Torque

V cm3/rev (in3/rev) Displacement Δp (bar) • V (cm3/rev)
Δp bar (psi) Pressure M= [Nm]
62,83 • ηhm
ηhm= ηhm (V, Δp, n) Hydro-mechanical efficiency
Notes: The torque absorbed from the shaft of the first pump results from the sum of the torques due to all the single stages.
The achieved value must not exceed the maximum torque limit given for the shaft of the first pump.
A: Front section (through drive)

B: MVP Rear pump (the same of single pump with side or rear ports)
Gear rear pump are also available, please see the respective technical catalogues.
O 06/06.2020
A
Pump
Flanged for Code
type
SAE A AS1
MVP30
SAE B AS5
MVP48 SAE B AS5
MVP60 SAE B AS5
DCAT048-ID02 53
MVP
MVP30 FRONT SECTION - DIMENSIONS AS1

Through drive SAE A Drive shafts: see page 32 The drawing shows a front section with
Mounting flanges: see page 36 clockwise rotation
IN
D1
Washer 10
Screw TCEI M10x25

UNI 5931
OUT
O 06/06.2020
Screws tightening torque Nm (lbf in)
V
70 ±7
(558 ÷ 682)
54 DCAT048-ID02
MVP
MVP30 COUPLINGS - DIMENSIONS
SAE “A” SPLINE 03

Available with flange code AS1
ANSI B92.1a-1976
Class 6 - 9 teeth
16/32 Pitch - 30 deg
Flat root - Side fit
Second pump side
MAX 100 Nm (885 lbf in)
SAE “A” STRAIGHT 31

SAE “A” Straight

Second pump side

05/10.2014
DCAT048-ID02 55
MVP

Through drive SAE B Drive shafts: see page 32 The drawing shows a front section with
IN
D1
Washer 12
UNI 5714
Nut M12
UNI 5588-A-8G
Stud M12x30
UNI 5911-8.8 O 06/06.2020
OUT
Nuts tightening torque Nm (lbf in)
V
100 ±10
(797 ÷ 974)
56 DCAT048-ID02
MVP
MVP30 COUPLINGS - DIMENSIONS AS5
SAE “B” SPLINE 04

ANSI B92.1a-1976
Class 6 - 13 teeth
16/32 Pitch - 30 deg
Flat root - Side fit
Second pump side

SAE “B” Straight

Second pump side

05/10.2014
DCAT048-ID02 57
MVP

Through drive SAE B Drive shafts: see page 33 The drawing shows a front section with
IN
D1
Washer 12
UNI 5714
Nut M12
UNI 5588-A-8G
Stud M12x30
UNI 5911-8.8
O 06/06.2020
OUT
Nuts tightening torque Nm (lbf in)
V
100 ±10
(797 ÷ 974)
58 DCAT048-ID02
MVP
SAE “B” SPLINE 04 SAE “BB” SPLINE 05

Available with flange code AS5 Available with flange code AS5
ANSI B92.1a-1976 ANSI B92.1a-1976

Class 6 - 13 teeth Class 6 - 15 teeth
16/32 Pitch - 30 deg 16/32 Pitch - 30 deg
Flat root - Side fit Flat root - Side fit
Second pump side Second pump side
MAX 200 Nm (1770 lbf in) MAX 250 Nm (2213 lbf in)
SAE “B” STRAIGHT 32 SAE “BB” STRAIGHT 33

SAE “B” Straight SAE “BB” Straight

05/10.2014
DCAT048-ID02 59
MVP

Through drive SAE B Drive shafts: see page 34 ÷ 35 The drawing shows a front section with
Mounting flanges: see page 36 ÷ 37 clockwise rotation
IN
D1
Washer 12
UNI 5714
Nut M12
UNI 5588-A-8G
Stud M12x30
O 06/06.2020
UNI 5931-8.8
OUT
V
100 ±10
(797 ÷ 974)
60 DCAT048-ID02
MVP
SAE “B” SPLINE 04 SAE “BB” SPLINE 05

Int. involute spline Int. involute spline

similar to ANSI B92.1 similar to ANSI B92.1
13 teeth - 16/32 Pitch 15 teeth - 16/32 Pitch
30 deg - Flat root 30 deg - Flat root
Side fit - Class 7 Side fit - Class 7
SAE “C” SPLINE 06

Int. involute spline

similar to ANSI B92.1
14 teeth - 12/24 Pitch
30 deg - Flat root
Side fit - Class 7
Second pump side

05/10.2014
DCAT048-ID02 61
MVP
FRONT SECTION KIT COVER
Kit cover is available to obtain single pumps starting from the front sections of multiple pumps.
Before closing the intermediate flange check that the coupling has been removed.
1 2 3 4
Kit part brake down

1 - Seal
2 - Flange
3 - Washers
4 - Screws
05/10.2014
Front section Kit cover

Pump Flanged A B
type for
Code Code
mm (in) mm (in)
209 14
MVP30 SAE A AS1 62100006
(8.2283) (0.5512)
209
MVP30 V
(8.2283
233 16 20 ±1
MVP48 SAE B AS5 62100007 (159 ÷ 195)
(9.1732) (0.6299)
253
MVP60
(9.9606)
62 DCAT048-ID02
MVP
NOTES
06/06.2020
DCAT048-ID02 63
MVP
HOW TO ORDER SINGLE PUMPS
1 2 3 4 5 6 7 8 ...
MVP30·28 S - 04 S5 - L MD/MB - N - ...
1 Pump type (max. displacement) Code Code Inlet/outlet ports 6
28 cm /rev (1.74 in /rev)
3 3
MVP 30·28 Nominal size
34,8 cm3/rev (2.12 in3/rev) MVP 30·34 Inlet IN Outlet OUT Pump type
SAE 3000 SAE 3000
45 cm3/rev (2.75 in3/rev) MVP 48·45
SAE FLANGED PORTS METRIC THREAD (SSM)
53,7 cm /rev (3.28 in /rev)
3 3
MVP 48·53
MD/MB 1” 1/4 3/4” MVP 30
60 cm3/rev (3.66 in3/rev) MVP 60·60
ME/MC 1” 1/2 1” MVP 48
72 cm3/rev (4.39 in3/rev) MVP 60·72
MF/MC 2” 1” MVP 60
84,7 cm3/rev (5.17 in3/rev) MVP 60·84
SAE FLANGED PORTS UNC THREAD (SSS)
SD/SB 1” 1/4 3/4” MVP 30
2 Rotation Code SE/SC 1” 1/2 1” MVP 48
Anti-clockwise S SF/SC 2” 1” MVP 60
Clockwise D SAE STRAIGHT THREAD PORTS (ODT)
OG/OD (b) 1” 1/4 3/4” MVP 30 O
3 Drive shaft (a) Code OH/OF (b) 1” 1/2 1” MVP 48
MF/OF 2” 1” MVP 60
SAE “B” spline (13 teeth) 04
SAE “B” spline (13 teeth) 4R
SAE “B” straight 32 Code Seals 7
SAE “BB” spline (15 teeth) 05 N Buna (standard)
SAE “BB” spline (15 teeth) 5R V Viton
SAE “C” spline (14 teeth) 06
SAE “C” spline (14 teeth) 6R
Code Regulators 8
SAE “C” straight 34
... See how to order on page 65 ÷ 67
4 Mounting flange (a) Code
SAE “B” 2 holes S5

SAE “C” 2 holes S7
5 Ports position Code

(a) Drive shafts availability at pages 32 ÷ 35 and
O 06/06.2020
Side L mounting flanges availability at pages 36 ÷ 37

Rear P (b) Only for rear ports
64 DCAT048-ID02
MVP
HOW TO ORDER REGULATORS
PRESSURE COMPENSATORS - FLOW COMPENSATORS (Load-sensing)
8 9 10 11 12 13
Pressure compensator
RP0 - Z - G
Pressure compensator RP1 - Z - G
Pressure compensator with flow

control RP1 - LS2 - Z - G
Dual setting pressure compensa-

tor
RP2 - 1 - Z - S - G
Dual setting pressure compensa-

tor with flow control RP2 - 1 - LS2 - Z - S - G
Flow compensator
LS0 - Z - G
Flow compensator for remote

control LS2 - Z - G
Pressure compensator for remote

control
LS3 - Z - G
8 Regulators type Code Code Flow control option 10

Pressure compensator RP0 LS2 Flow compensator
Pressure compensator RP1
Dual setting pressure compensator RP2 Code Restrictor option 11
Flow compensator LS0
Without restrictor (standard - no code)
Flow compensator for remote control LS2
Z Damping restrictor (only for critical applications)
Pressure compensator for remote control LS3
Code Connector type 12

9 Valve type O Code
S DIN 43650 (standard)
Normally closed 12 V DC 1
D Deutsch DT04-2P
O 06/06.2020
Normally open 12 V DC 6
Code O Displacement limiter 13
E Max. displacement limiter
G Min. and Max. displacement limiter
ORDER EXAMPLE
MVP60 pump with dual setting pressure compensator:
MVP60.60S-05S5-LMF/MC-N-RP2-1-S-G
DCAT048-ID02 65
MVP
ELECTRO-PROPORTIONAL PRESSURE AND DISPLACEMENT COMPENSATORS - UNLOADING VALVES
8 9 10 11 12 13 14 15 16
Electro-proportional pressure
PEC - 1 - A - ... / ... - D - G
compensator
PEC - 1 - A - LS2 - ... / ... - D - G
compensator with flow control
compensator plus angular sensor PECA - 1 - A - ... ... D G
compensator plus angular sensor PECA - 1 - A - LS2 - ... ... - D - G
with flow control
Unloading valve
O U.. - Z - G
Electro-proportional displace-
O DEC - 1 - LS2 - D - G
ment compensator
8 Regulators type (a) Code Code Flow control option 11

Electro-proportional pressure compensator PEC LS2 Flow compensator for remote control
Electro-proportional pressure compensator and
PECA
swashplate angular sensor (a)
Code Restrictor option 12
Unloading valve - Normally closed 12 V DC U1
Unloading valve - Normally closed 24 V DC U2
Z Damping restrictor (only for critical applications)
Unloading valve - Normally open 12 V DC U6
Unloading valve - Normally open 24 V DC U7
Electro-proportional displacement compensator DEC Code Min. pressure setting 13
... Please specify the requested value in bar
9 Valve type Code
Code Max. pressure setting 14
Normally closed 24 V DC 2 ... Please specify the requested value in bar
Normally open 24 V DC 7 Code Connector type 15
S DIN 43650
10 Position Code D Deutsch DT04-2P
O 06/06.2020
Position 0° A
Position 90° B Code O Displacement limiter 16
(a) PECA: not available with MVP 30
ORDER EXAMPLE
MVP60 pump with electro-proportional pressure compensa-
tor with flow control:
MVP60.60S-05S5-LMF/MC-N-PEC-1-A-LS2-100/300-D-G
66 DCAT048-ID02
MVP
TORQUE LIMITERS
8 9 10 11 12 13 14 15 16
Torque limiter - standard
RN0 - Z - G - ... / ...
Torque limiter - internal pilot

RN1 - Z - G - ... / ...
Dual setting torque limiter with

RN2 - 1 - S - LS0 - Z - G - ... / ... / ...
flow control
Dual setting torque limiter with RN2 - 1 - S - LS2 - Z - G - ... / ... / ...
remote flow control
High performance torque limiter

O RN3 - Z - G - ... / ...
8 Regulators type Code Code Flow control option 11

Torque limiter - standard RN0 LS0 Flow compensator
Torque limiter - internal pilot RN1 LS2 Flow compensator for remote control
Dual setting torque limiter with flow control RN2
High performance torque limiter RN3 Code Restrictor option 12
9 Valve type Code Z Damping restrictor (only for critical applications)
Normally closed 24 V DC 2 Code O Displacement limiter 13
Normally open 12 V DC 6 E Max. displacement limiter
Normally open 24 V DC 7 G Min. and Max. displacement limiter
10 Connector type Code Code Torque limiter setting (a) 14

DIN 43650 (standard) S ... Please specify the requested torque value in Nm
Deutsch DT04-2P D
Code Second torque limiter setting (a) 15
... Please specify the requested torque value in Nm
O 06/06.2020
Code Torque limiter setting speed (b) 16

... Please specify the requested speed value
(a) Refer to page 47 ÷ 49 for more information

(b) Do not exceed the maximum speed shown on page 7 ÷ 9
ORDER EXAMPLE
MVP60 pump with dual setting torque limiter with flow control:
MVP60.60S-05S5-LMF/MC-N-RN2-1-S-LS0-Z-G-150/200/2100
DCAT048-ID02 67
MVP
HOW TO ORDER MULTIPLE PUMPS - PISTON PUMP/GEAR PUMP
Common inlet
1 2 3 4 5 6 7 8 ... 9 10 7 11 12 13 14
MVP30·28 S - 04 S5 - L MD/MB - N - ... - G - P7 - A (# / # / #) /
Front section
KP20·6,3 S - - L **/GD - N5 - N - P
Rear section

Front section - The same of single pumps MVP ... Nominal size
Rear section - KAPPA 20 gear pumps (a) KP 20 ... Inlet IN Outlet OUT Pump type
SAE 3000 SAE 3000
Rear section - POLARIS PH gear pumps (b) PHP 20 ...
SD/SB 1” 1/4 3/4” MVP 30
2 Rotation Code
SE/SC 1” 1/2 1” MVP 48
Anti-clockwise S
SF/SC 2” 1” MVP 60
Clockwise D
SAE STRAIGHT THREAD PORTS (ODT)
— — MVP 30
3 Drive shaft (c) Code
O
— — MVP 48
SAE “B” spline (13 teeth) 04
MF/OF 2” 1” MVP 60
SAE “B” spline (13 teeth) 4R
SAE “B” straight 32
SAE “BB” spline (15 teeth) 05 Code Seals 7
SAE “BB” spline (15 teeth) 5R N Buna (standard)
SAE “C” spline (14 teeth) 06 V Viton
SAE “C” straight 34 Code Regulators 8
... See how to order on page 65 ÷ 67
4 Mounting flange (c) Code

5 Ports position Code
Side L Code Intermediate flange 10

FRONT SECTION
6 Inlet/outlet ports (a) - (b) Code P7 Flanged for KP20
O 06/06.2020
Nominal size I7 Flanged for PHP20

Pump type Inlet IN Outlet OUT
REAR SECTION
SAE 3000 SAE 6000
N5 Kappa 20 (common inlet)
SAE FLANGED PORTS METRIC THREAD (SSM)
S7 Polaris PHP 20 (common inlet)
MVP 30 1” 1/4 3/4” MD/MB
MVP 48 1” 1/2 1” ME/MC
MVP 60 2” 1” 1/4 MF/MC Code Sections 11
A Front
P Rear
68 DCAT048-ID02
MVP
HOW TO ORDER MULTIPLE PUMPS - PISTON PUMP/GEAR PUMP
Code Torque limiter setting (#) 12 Omit code only if ordering assembled multiple pumps
(#) Only for torque limiter. Refer to page 67 for more information.
... Please specify the requested torque value in Nm
Write these codes at the end only if ordering assembled
multiple pumps
Code Second torque limiter setting (#) 13 (a) KAPPA 20 gear pumps:
... Please specify the requested torque value in Nm displacements on page 22, 26 and 30. For more information,
please see the respective technical catalogue
Code Torque limiter setting speed (#) 14 (b) POLARIS PH gear pumps
displacements on page 23, 27 and 31. For more information,
... Please specify the requested speed value please see the respective technical catalogue
(c) Drive shafts availability at pages 32 ÷ 35 and mounting
flanges availability at pages 36 ÷ 37
ORDER EXAMPLE
Common inlet double pump MVP 60 with RN1 torque limiter-internal pilot + PHP20 gear pump.
INDIVIDUAL SECTIONS
Front section
MVP 60.60S-06S8-LMF/MC-N-RN1-G-I7-A (100/2500)
Rear section PHP 20.23S-L **/GD-S7-N-P
ASSEMBLED DOUBLE PUMP
MVP 60.60S-06S8-LMF/MC-N-RN1-G/PHP 20.23-L**/GD (100/2500)

05/10.2014
DCAT048-ID02 69
MVP
HOW TO ORDER MULTIPLE PUMPS - PISTON PUMP/PISTON PUMP
Through drive O
1 2 3 4 5 6 7 8 ... 9 10 11 12 13 14
MVP 60·60 S - 05 S5 - L MF/MC - N - ... - G - AS5 - 04 - (# / # / #) /
Front section (through drive)
MVP 30·28 S - 04 S5 - L MD/MB - N - ... - G - - - ... / ... / ...
Rear section (single pump)

Front section MVP (the same of single pumps) (a) MVP ... Nominal size
Rear section MVP (the same of single pumps) (a) MVP ... Inlet IN Outlet OUT Pump type
SAE 3000 SAE 3000
SAE STRAIGHT THREAD PORTS (ODT)
2 Rotation Code
— — MVP 30
Anti-clockwise S O
— — MVP 48
Clockwise D
MF/OF 2” 1” MVP 60
3 Drive shaft (b) Code
SAE “B” spline (13 teeth) 04 Code Seals 7

SAE “B” spline (13 teeth) 4R N Buna (standard)
SAE “B” straight 32 V Viton
SAE “BB” spline (15 teeth) 05
SAE “BB” spline (15 teeth) 5R Code Regulators 8
SAE “C” spline (14 teeth) 06 ... See how to order on page 65 ÷ 67
SAE “C” straight 34
4 Mounting flange (b) Code E Max. displacement limiter
SAE “C” 4 holes S8 Code Intermediate flange (c) 10
AS1 SAE “A” 2 holes
5 Ports position Code AS5 SAE “B” 2 holes
Side L
Code Coupling (d) 11

6 Inlet/outlet ports Code
03 SAE “A” spline (9 teeth)
Nominal size
31 SAE “A” straight
O 06/06.2020
Pump type Inlet IN Outlet OUT

SAE 3000 SAE 6000 04 SAE “B” spline (13 teeth)
SAE FLANGED PORTS METRIC THREAD (SSM) 32 SAE “B” straight
MVP 30 1” 1/4 3/4” MD/MB 05 SAE “BB” spline (15 teeth)
MVP 48 1” 1/2 1” ME/MC 33 SAE “BB” straight
MVP 60 2” 1” 1/4 MF/MC 06 SAE “C” spline (14 teeth)
MVP 30 1” 1/4 3/4” SD/SB Code Torque limiter setting (#) 12
MVP 48 1” 1/2 1” SE/SC ... Please specify the requested torque value in Nm
MVP 60 2” 1” SF/SC
70 DCAT048-ID02
MVP
HOW TO ORDER MULTIPLE PUMPS - PISTON PUMP/PISTON PUMP
Code Second torque limiter setting (#) 13 (a) Displacements on page 64
... Please specify the requested torque value in Nm (b) Drive shafts availability at pages 32 ÷ 35 and
mounting flanges availability at pages 36 ÷ 37
(c) Intermediate flanges on page 53
Code Torque limiter setting speed (#) 14
(d) Couplings availability:
... Please specify the requested speed value MVP30 on page 55 and 57
MVP48 on page 59
MVP60 on page 61
Omit code only if ordering assembled multiple pumps

(#) Only for torque limiter. Refer to page 67 for more information.
ORDER EXAMPLE
Through drive double pump MVP 60 with RN2 (dual setting torque limiter with remote flow control) + MVP 30 with LS0 flow
compensator.
INDIVIDUAL SECTIONS
Front section
MVP 60.60S-06S8-LMF/MC-N-RN2-1-S-LS2-G-AS5/04 (70/85/2600)
Rear section
MVP 30.34S-04S5-LMD/MB-N-LS0-Z-G
MVP 60.60S-06S8-LMF/MC-N-RN2-1-S-LS2-G (70/85/2600)/ MVP 30.34S-04S5-LMD/MB-N-LS0-Z-G
Through drive double pump MVP 48 with RN0 (standard torque limiter) + KP 30 gear pump.
INDIVIDUAL SECTIONS
Front section
05/10.2014
MVP 48.45S-04S5-LME/MC-N-RN0-G-AS5/04 (80/2300)
Rear section KP30.51S0-04S5-LED/EB-N-P
POMPA MVP 48.45S-04S5-LME/MC-N-RN0-G/KP30.51-04S5-LED/EB (80/2300)
Our policy is one of continuous improvement in product. Specification of items may, therefore, be changed without notice.
DCAT048-ID02 71
MVP 06 T A Edition: 06/06.2020 Replaces: MVP 05 T A
VARIABLE
DISPLACEMENTS
Headquarters:
AXIAL PISTON
CASAPPA S.p.A.
Via Balestrieri, 1 PUMPS
43044 Lemignano di Collecchio
Parma (Italy)
Tel. (+39) 0521 30 41 11
Fax (+39) 0521 80 46 00
E-mail: [email protected]
www.casappa.com

Variable Displacements Axial Piston Pumps: Edition: 06/06.2020 Replaces: MVP 05 T A

Uploaded by

Copyright:

Available Formats

Variable Displacements Axial Piston Pumps: Edition: 06/06.2020 Replaces: MVP 05 T A

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Variable Displacements Axial Piston Pumps: Edition: 06/06.2020 Replaces: MVP 05 T A

Uploaded by

Copyright:

Available Formats

MVP 06 T A Edition: 06/06.

2020 Replaces: MVP 05 T A

GENERAL INFORMATION / INSTRUCTIONS....................................................................................................................... 4

DISPLACEMENTS AND WORKING PRESSURES RANGE..................................................................................................... 6

SINGLE PUMPS AND COMMON INLET MULTIPLE PUMPS

MULTIPLE PUMPS WITH THROUGH DRIVE....................................................................................................................... 53

O Modification from former edition.

DISPLACEMENTS TYPICAL APPLICATIONS

GENERAL INFORMATION / INSTRUCTIONS

DIRECTION OF ROTATION LINES

Max storage time in ideal conditions is 24 months.

The pump can be mounted in a horizontal or vertical position.

HORIZONTAL MOUNTING VERTICAL MOUNTING

Arrangement inside the tank. Arrangement inside the tank.

A ≥ 200 mm (7.874 in) A ≥ 200 mm (7.874 in)

Arrangement inside the tank. Arrangement inside the tank.

(24 in Hg) (24 in Hg)

Arrangement outside the tank

C = 200 mm (7.874 in)

DISPLACEMENTS AND WORKING PRESSURES RANGE

p3 p2 System pressure (relief valve setting)

Please note that both relief valve setting and overshoot

For high frequency applications please consult our pre-

Technical data with mineral oil

HL or HLP mineral oil based hydraulic fluid to DIN 51524

(1) = with an inlet pressure of 1 bar abs (14.5 psi) and

HFA - Oil emulsion in water (5 ÷ 15 % of oil)

HFB - Water emulsion in oil (40 % of water)

HFC - Water-glycol (35 ÷ 55 % of water)

(1) = with an inlet pressure of 1 bar abs (14.5 psi) and

HFD - Phosphate ester

Technical data restrictions with biodegradable fluids

Operating min. -15 (5)

Design calculations for pump

Q l/min (US gpm) Flow Q = Q theor. • ηv

M Nm (lbf in) Torque [l/min]

Max. permissible load on drive shaft

MVP MVP MVP MVP MVP MVP MVP

N 1000 1000 1500 1500 2000 2000 2000

N 1500 1500 1500 1500 3000 3000 3000

13 (0,9) 120 120 110 103 95

14.5 (1,0) 120 120 115 107 100

Max. speed must not exceed the limits specified at page 7.

Definition of rotation direction looking at the drive shaft

Side ports Rear ports

Side ports Rear ports

Max.displacement Max. displacement

Tightening torque 15±1 Nm (124 ÷ 142 lbf in)

MVP30 MVP48 MVP60

For different setting range, please consult our pre-sales department.

L CG1 • m1 + (L INT + L CG2) • m2

MMF: Load moment on mounting flange

MVP30 MVP48 MVP60

L CG1 mm (in) 100 (3.94) 116 (4.57) 120 (4.72)

L CG2 mm (in) 90 (3.54) 99 (3.90) 107 (4.21)

L INT mm (in) 208 (8.19) 233 (9.17) 253 (9.96)

For single pumps refer to L CG2 values

MVP30•28 OPERATING CURVES

Delivery / power Noise level Distance from microphone to