JOB NO. 115550 ITEM NO.

C6000
CENTRIFUGAL AND AXIAL COMPRESSOR REVISION NO. 1 DATE Thursday, March 29, 2012
DATA SHEET (API 617-7TH Chapter 2) PAGE 1 OF 7 BY Y.Y.Peignet
SI UNITS (1-1.6.5)
1 APPLICABLE TO: PROPOSAL PURCHASE AS BUILT
2 FOR Kinsale Energy UNIT C6000
3 SITE Kinsale Alpha / Irish Sea SERIAL NO.
4 SERVICE Gas Injection NO. REQUIRED
5 MANUFACTURER DRESSER-RAND DRIVER TYPE (1-3.1.1) GAS TURBINE / Solar Taurus 60
6 MODEL D06R6S DRIVER ITEM NO.
7
8 INFORMATION TO BE COMPLETED: BY PURCHASER BY MANUFACTURER MUTUAL AGREEMENT (PRIOR TO PURCHASE)
9 OPERATING CONDITIONS
10
11 (ALL DATA ON PER UNIT BASIS) Guaranteed Early Mid End Max Head Rated Max Flow
12 D6R6S D6R6S D6R6S D6R6S D6R6S D6R6S D6R6S
13 SEC #1 SEC #1 SEC #1 SEC #1 SEC #1 SEC #1 SEC #1
14 GAS HANDLED (ALSO SEE PAGE ) C6000 Rich C6000 Rich C6000 Rich C6000 Rich C6000 Rich C6000 Rich C6000 Rich
15 GAS PROPERTIES (1-2.1.1.4)
16 MMSM3/Day 1.0133 & 15.5 (DRY) 2.548 1.416 1.416 1.416 2.180 2.803 3.114
17 WEIGHT FLOW, (Kg/Hr) (WET) 83 000 46 107 46 107 46 107 71 006 91 293 101 437
18 RECYCLE WEIGHT FLOW, (Kg/Hr) (WET) 0 0 8 408 14 958 0 0 0
18 INLET CONDITIONS
19 SPECIFIED PRESSURE (BarA) 33.00 33.00 33.00 33.00 33.00 33.00 33.00
20 THROTTLED PRESSURE (BarA)
21 TEMPERATURE (°C) 16.00 21.00 21.00 21.00 16.00 16.00 16.00
22 RELATIVE HUMIDITY (%)
23 MOLECULAR WEIGHT 18.52 18.52 18.52 18.52 18.52 18.52 18.52
24 Cp/Cv (Kavg) 1.273 1.273 1.267 1.263 1.264 1.273 1.273
25 COMPRESSIBILITY (Z1) 0.9195 0.9238 0.9238 0.9238 0.9195 0.9195 0.9195
26 INLET VOLUME, (M3/Min)(WET) 50.05 28.42 28.42 28.42 42.81 55.05 61.16
27 DISCHARGE CONDITIONS
28 PRESSURE (BarA) 96.00 73.00 96.00 111.0 121.0 96.00 84.00
29 TEMPERATURE (°C) 114.4 93.5 122 137.4 139.4 115 104.9
30 Cp/Cv(Kavg) 1.273 1.273 1.267 1.263 1.264 1.273 1.273
31 COMPRESSIBILITY (ZAvg) 0.9438 0.9354 0.9502 0.9576 0.9587 0.9444 0.941
32 FLANGE FLOWS
33 INLET FLANGE WEIGHT FLOW, Kg/Hr (WET) 83000 46 107 54515 61065 71 006 91 293 101 437
34 INLET FLANGE VOLUME, (M3/Min)(WET) 50.05 28.42 33.6 37.64 42.81 55.05 61.16
35 DISCHARGE FLANGE WEIGHT FLOW, Kg/Hr (WET) 83 000 46 107 57 205 61065 71 006 91 293 101 437
36 DISCHARGE FLANGE VOLUME, (M3/Min)(WET) 23.67 16.26 15.96 16.18 17.37 26.09 32.15
37
38 GHP REQUIRED (KW) 4453 1809 3 181 3999 4 894 4942 4933
39 TRAIN BHP REQUIRED EXCL. EXT. LOSSES (KW) 4489 1834 3 214 4038 4 935 4980 4971
40 BHP REQ. AT DRIVER INCL. EXT. LOSSES (GEAR, ETC.) (KW)
41 SPEED (RPM) 12634 10265 12 019 13057 13533 12918 12807
42 TURNDOWN (%)
43 POLYTROPIC HEAD (M Kgf/Kg) 15291 11132 15 641 18216 19347 15314 13195
44 POLYTROPIC EFFICIENCY (%) 77.64 77.3 76.1 75.76 76.48 77.07 73.91
45 CERTIFIED POINT YES NO NO NO NO NO NO
46 EXPECTED OPERATION AT EACH CONDITION (%)
47 PERFORMANCE CURVE NUMBER
48 PROCESS CONTROL (1-3.4.2.1)
49 METHOD SUCTION THROTTLING VARIABLE INLET SPEED VARIATION DISCHARGE COOLED BYPASS
50 FROM BarA GUIDE VANES FROM 105 % 14300 rpm BLOWOFF FROM
51 TO BarA (2-2.4.1) TO 70 % 9533 rpm TO TO
52 SIGNAL SOURCE (1-3.4.2.1)
53 TYPE ELECTRONIC PNEUMATIC OTHER
54 RANGE MA BarG
55
56 ANTI-SURGE SYSTEM (1-3.4.2.2)

57 REMARKS: Brake Power is guaranteed per API 617 at 4 387 kW +4% (max 4 562 kW) (refer to TR140151 KE rev0008 )
58 Design Pressure Rating is 1795psiG / 123.8 barG ; Compressor and piping shall be protected accordingly (relief valve)
59 NOTE 1: IF GAS ANALYSIS IS GIVEN, MANUFACTURER SHALL SUPPLY DATA, OTHERWISE DATA SHALL BE SUPPLIED BY USER
 JOB NO. 115550 ITEM NO. C6000
CENTRIFUGAL AND AXIAL COMPRESSOR REVISION NO. 1 DATE Thursday, March 29, 2012
DATA SHEET (API 617-7TH Chapter 2) PAGE 2 OF 7 BY Y.Y.Peignet
SI UNITS (1-1.6.5)
1 OPERATING CONDITIONS (Continued) (1-2.1.1.1) (1-3.1.2) (1-3.1.3)
2 GAS ANALYSIS:
REMARKS:
3 MOL % C6000 Rich C6000 Lean
4 MW
5 Methane (C1) 16.043000 87.429240 98.840910
6 Ethane (C2) 30.070000 6.975876 0.594884
7 Propane (C3) 44.097000 2.191612 0.036878
8 n-Butane (n-C4) 58.123000 0.210232 0.013989
9 i-Butane (i-C4) 58.123000 0.210232 0.019585
10 n-Pentane (n-C5) 72.150000 0.030793 0.006762
11 i-Pentane (i-C5) 72.150000 0.030793 0.009016
12 n-Hexane (n-C6) 86.177000 0.010742 0.001887
13 Carbon Dioxide 44.010000 1.909883 0.284552
14 Nitrogen 28.013000 0.991366 0.191570
15 n-Heptane (n-C7) 100.200000 0.009239
16
17 Water Gas dehydrated to NTS specification of 50mg/m3
18
19
20
21
22
23
24
25 TOTAL 100.000000 100.000000 Gas Equation of state : D-R Standard
26 AVG. MOL. WT. 18.515940 16.263610
27 LOCATION: (1-2.1.8) NOISE SPECIFICATIONS: (1-2.1.9)
28 INDOOR OUTDOOR GRADE APPLICABLE TO MACHINE:
29 HEATED UNDER ROOF MEZZANINE SEE SPECIFICATION
30 UNHEATED PARTIAL SIDES APPLICABLE TO NEIGHBORHOOD:
31 ELEC. AREA CLASSIFICATION (1-2.1.14) CL GR DIV SEE SPECIFICATION
32 SITE DATA (1-2.1.8) ACOUSTIC HOUSING: YES NO
33 ELEVATION 30.5 m BAROMETER 1.013 BarA APPLICABLE SPECIFICATIONS:
34 RANGE OF AMBIENT TEMPS: API 617, 7TH CHAPTER 1&2
35 DRY BULB WET BULB VENDOR HAVING UNIT RESPONSIBILITY (1-1.5.52) (1-1.8) (1-2.1.3)
36 NORMAL °C 7
37 MAXIMUM °C 21 GOVERNING SPECIFICATION (IF DIFFERENT)
38 MINIMUM °C -8
39 °C
40 UNUSUAL CONDITIONS: DUST FUMES PAINTING:
41 °C MANUFACTURER'S STD.
42 OTHER (1-2.1.8) OTHER
43
44 COPPER AND COPPER ALLOYS PROHIBITED (1-2.2.1.14) SHIPMENT: (1-4.4)
45 COATING: (1-2.2.1.16) DOMESTIC EXPORT EXPORT BOXING REQ'D.
46 ROTATING COMPONENTS OUTDOOR STORAGE MORE THAN 6 MONTHS (1-4.4.1) MO
47 STATIONARY COMPONENTS SPARE ROTOR ASSEMBLY PACKAGE (1-4.4.3.10)
48 REMARKS: HORIZONTAL STORAGE VERTICAL STORAGE
49
50
51
52
 JOB NO. 115550 ITEM NO. C6000
CENTRIFUGAL AND AXIAL COMPRESSOR REVISION NO. 1 DATE Thursday, March 29, 2012
DATA SHEET (API 617-7TH Chapter 2) PAGE 3 OF 7 BY Y.Y.Peignet
SI UNITS (1-1.6.5)
1 CONSTRUCTION FEATURES
2 SPEEDS: DIAPHRAGMS:
3 MAX. CONT. 14 300 RPM TRIP 15 015 RPM MATERIAL ASTM A36 Carbon Steel Plate
4 MAX. TIP SPEEDS: 244. MPS @ 100% SPEED AXIALLY SPLIT YES NO (2-2.4.8)
5 256. MPS @ MAX. CONT. SPEED
6 LATERAL CRITICAL SPEEDS (DAMPED) INTERMEDIATE MAIN PROCESS CONNECTIONS (2-2.4.5
7 FIRST CRITICAL 7540 to 9300 RPM MODE DISCH. PRESSURE (BarA) MAX MIN

8 SECOND CRITICAL 27660 to 27780 RPM MODE INLET PRESSURE (BarA) MAX MIN

9 THIRD CRITICAL RPM MODE DIAPHRAGM MAX. ∆ P (BarA) 23

10 FOURTH CRITICAL RPM MODE IMPELLERS:
11 LATERAL ANALYSIS ADDITIONAL REQUIREMENTS (1-2.6.2.14) NO. 6 DIA (mm) (5)@325.6,(1)@341.9
12 TRAIN LATERAL ANALYSIS REQUIRED (1-2.6.2.6) NO. VANES EA. IMPELLER (4)@19,(2)@17
13 TRAIN TORSIONAL ANALYSIS REQUIRED (1-2.6.7.1) TYPE (OPEN, ENCLOSED, ETC.) ENCLOSED
14 TORSIONAL CRITICAL SPEEDS: TYPE FABRICATION FABRICATED
15 FIRST CRITICAL 4322 RPM MATERIAL (1)410,(5)@4330
16 SECOND CRITICAL 45757 RPM MIN. YIELD STRENGTH (kPa) 530888
17 THIRD CRITICAL RPM HARDNESS: (Rc) (BRINNEL) MAX 197 MIN 255
18 FOURTH CRITICAL RPM SMALLEST TIP INTERNAL WIDTH (mm) 8.707
19 LIST OF TRAIN UNDESIRABLE SPEEDS (1-2.6.1.4) MAX. MACH. NO. @ IMPELLER EYE 0.39
20 VIBRATION: MAX. IMPELLER HEAD@100% SPD (M Kgf/Kg) 2661.
21 ALLOWABLE TEST LEVEL 23.3 MICS SHAFT:
22 (PEAK TO PEAK) ONE PIECE BUILT UP
23 NAMEPLATE (2-2.11.2) MATERIAL Grade 4340 Alloy Steel Forging High Strength
24 US CUSTOMARY METRIC DIA @ IMPELLERS (mm) (6)@132.272 DIA @ COUPLING (mm)
25 ROTATION, VIEWED FROM DRIVEN END CW CCW SHAFT END: TAPERED CYLINDRICAL
26 MATERIALS INSPECTION REQUIREMENTS (1-4.2.2.1) SPLINED INTEGRAL FLANGE
27 RADIOGRAPHY REQUIRED FOR MIN. YIELD STRENGTH (kPa) 861 845
28 ULTRASONIC REQUIRED FOR SHAFT HARDNESS (BNH)(Rc) 331.0
29 MAGNETIC PARTICLE REQUIRED FOR MAX TORQUE CAPABILITY (N-M) 7000
30 LIQUID PENETRANT REQUIRED FOR BALANCE PISTON:
31 LOW TEMPERATURE (1-2.2.1.15.3) MATERIAL Grade 4140 Alloy Steel Forging AREA 14813 mm²
32 MIN.DESIGN METAL TEMPERATURE (°C) FIXATION METHOD SHRINK FIT
33 AT CONCURRANT PRESSURE (BarA) NORMAL CLEARANCE (mm) 0.29 (radial)
34 OTHER TRAIN COMPONENTS (1-2.2.1.15.2) FLOW WITH NORMAL CLEARANCE (Kg/Hr) 3000
35 CASING: FLOW WITH 2x NORMAL CLEARANCE (Kg/Hr) 7000
36 MODEL D6R6S PRESS. CONN. BAL LINE DOWNSTREAM (2-2.5.4.3)
37 CASING SPLIT RADIAL SHAFT SLEEVES:
38 MATERIAL ASTM A350 Gr LF2 Carbon Steel with -50°F Impact AT INTERSTG. CLOSE MATL A743
39 THICKNESS (mm) 63.50 CORR. ALLOW. (mm) 3.175 CLEARANCE POINTS
40 MAX. ALLOWABLE PRESS 123 BarG AT SHAFT SEALS MATL A743
41 TEST PRESS (BarG): HYDRO 185 ACCESSIBLE (2-2.8.3)
42 MAX. ALLOWABLE TEMPERATURE (°C) 193 ROTOR
43 MAX OPER. TEMP. 193 °C MIN. OPER. TEMP. -29 °C DISASSEMBLY AND REASSEMBLY (1-2.6.8.2.1.1)
44 MAX CASING CAPACITY (ICFM) 100 AT SPEED BALANCING (1-2.6.8.3)
45 SYSTEM RELIEF VALVE SET PT. (2-2.3.1.1) 120 BarG SEQUENTIAL LOW SPEED BAL. PREC. AT SPEED BAL. (1-2.6.8.6)
46 Q.C. OF INACCESSIBLE WELDS (1-2.3.1.11.2) RESIDUAL BALANCE CHECK (1-2.6.8.7)
47 GUIDE VANES LABYRINTHS:
48 MATERIAL ASTM A36 INTERSTAGE
49 NO. VANES GUIDE VANE 12 TYPE KNIFE EDGE MATERIAL A850
50 IGV EXTERNAL PURGE (2-2.4.2) BALANCE PISTON
51 VANE CONTROL SYSTEM (2-2.4.3) TYPE KNIFE EDGE MATERIAL A850
 JOB NO. 115550 ITEM NO. C6000
CENTRIFUGAL AND AXIAL COMPRESSOR REVISION NO. 1 DATE Thursday, March 29, 2012
DATA SHEET (API 617-7TH Chapter 2) PAGE 4 OF 7 BY Y.Y.Peignet
SI UNITS (1-1.6.5)
1 CONSTRUCTION FEATURES (CONTINUED)
2 SHAFT SEALS: BUFFER GAS CONTROL SYSTEM SCHEMATIC BY VENDOR
3 SEAL TYPE (1-2.8.1.3) Tandem with intermediate laby (no buffer injection) PRESSURIZING GAS FOR SUBATMOSPHERIC SEALS (1-2.8.2.4)
4 MAX SEALING/SETTLING OUT PRESSURE (1-2.8.1.1) (BarA) See note 1 EDUCTOR INJECTION (1-2.8.2.3)
5 MIN.SEALING PRESSURE (BarA) SEAL MANUFACTURER FlowServe
6 SUPPLEMENTAL DEVICE REQUIRED FOR CONTACT LEAKAGE TO PROCESS (GAL/DAY/SEAL)
7 SEALS (1-2.8.3.4) TYPE BUFFER GAS REQUIRED FOR:
8 BUFFER GAS SYSTEM REQUIRED (1-2.8.1.5) AIR RUN-IN OTHER
9 TYPE BUFFER GAS (1-2.8.1.5) FLOW (PER SEAL):
10 PRESSURE (1-2.8.1.6) BarA NORM: lit/Min@ Bar ∆ P
11 FLOWRATE Kg/Hr MAX. lit/Min@ Bar ∆ P
12 FILTRATION BEARING HOUSING CONSTRUCTION:
13 MANIFOLD (1-2.8.1.7) TYPE (SEPARATE, INTEGRAL) SEPARATE SPLIT AXIAL
14 METHOD OF CONTROL (1-2.8.1.5) Flow Control MATERIAL ASTM A36 Carbon Steel Plate

15 AXIAL COMPRESSOR
16 STAGE 1 2 3 4 5 6 7 8 9
17 ROTOR
18 BLADE MATERIAL
19 BLADE ROOT TYPE
20 CORD WIDTH (mm)
21 OUTER DIAMETER (mm)
22 BLADE HEIGHT (mm)
23 BLADE QUANTITY
24 STATOR
25 BLADE MATERIAL
26 TYPE (MOVABLE, FIXED,
27 ADJUSTABLE) (2-3.4.2.3)
28 CORD WIDTH (mm)
29 BLADE QUANTITY
30
31 STAGE 10 11 12 13 14 15 16 17 18
32 ROTOR
33 BLADE MATERIAL
34 BLADE ROOT TYPE
35 CORD WIDTH (mm)
36 OUTER DIAMETER (mm)
37 BLADE HEIGHT (mm)
38 BLADE QUANTITY
39 STATOR
40 BLADE MATERIAL
41 TYPE (MOVABLE, FIXED,
42 ADJUSTABLE) (2-3.4.2.3)
43 CORD WIDTH (mm)
44 BLADE QUANTITY
45
46 REMARKS: Note 1 : Normal Dynamic sealing Pressure = 32 Bar G / Min. Dyn. P = 0.2 barG / Max Dyn. P = 95 barG
47 Settle Out Pressure (with start up allowed) = 55 Bar G / Max Allowed Static Pressure (without start up): 95 Bar G
48 Primary seal feeded with fuel gas, No buffer gas into secondary seals
49 Barrier seal (tertiary) feeded with air : Max Flow per Barrier 530 Std L/mn @ MCoS / 900 Std L/mn @ 0 rpm