Scribd Logo
Upload

Welcome to Scribd!

  • 47 views

    Minimum Technical Specification For 88.9

    Uploaded by

    Rambabu Ch
    The document provides the minimum technical specifications for 88.9 mm external upset drill pipe assemblies for use in water well drilling. The specifications include: 1) The drill pipe assemblies must be 6.096 meters long with an outside diameter of 88.9 mm and wall thickness of 9.35 mm. 2) The material must be alloy steel equivalent to API SCT-N80 grade or higher, with a minimum yield strength of 517 N/mm2 and tensile strength of 690 N/mm2. 3) Tool joints must be made of alloy steel and heat treated to a minimum hardness of 285 BHN, with threads conforming to API 31⁄2 IF standards.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Minimum Technical Specification For 88.9

    Uploaded by

    Rambabu Ch
    47 views2 pages
    The document provides the minimum technical specifications for 88.9 mm external upset drill pipe assemblies for use in water well drilling. The specifications include: 1) The drill pipe assemblies must be 6.096 meters long with an outside diameter of 88.9 mm and wall thickness of 9.35 mm. 2) The material must be alloy steel equivalent to API SCT-N80 grade or higher, with a minimum yield strength of 517 N/mm2 and tensile strength of 690 N/mm2. 3) Tool joints must be made of alloy steel and heat treated to a minimum hardness of 285 BHN, with threads conforming to API 31⁄2 IF standards.

    Original Title

    MINIMUM TECHNICAL SPECIFICATION FOR 88.9

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides the minimum technical specifications for 88.9 mm external upset drill pipe assemblies for use in water well drilling. The specifications include: 1) The drill pipe assemblies must be 6.096 meters long with an outside diameter of 88.9 mm and wall thickness of 9.35 mm. 2) The material must be alloy steel equivalent to API SCT-N80 grade or higher, with a minimum yield strength of 517 N/mm2 and tensile strength of 690 N/mm2. 3) Tool joints must be made of alloy steel and heat treated to a minimum hardness of 285 BHN, with threads conforming to API 31⁄2 IF standards.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    47 views2 pages

    Minimum Technical Specification For 88.9

    Uploaded by

    Rambabu Ch
    The document provides the minimum technical specifications for 88.9 mm external upset drill pipe assemblies for use in water well drilling. The specifications include: 1) The drill pipe assemblies must be 6.096 meters long with an outside diameter of 88.9 mm and wall thickness of 9.35 mm. 2) The material must be alloy steel equivalent to API SCT-N80 grade or higher, with a minimum yield strength of 517 N/mm2 and tensile strength of 690 N/mm2. 3) Tool joints must be made of alloy steel and heat treated to a minimum hardness of 285 BHN, with threads conforming to API 31⁄2 IF standards.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    MINIMUM TECHNICAL SPECIFICATION FOR 88.

    9 MM EXTERNAL
    UPSET DRILL PIPE ASSEMBLIES FOR USE IN WATER WELL DRILLING
    APPLICATION:

    External upset drill pipes of 88.9mm dia and 6.096 meters long having wall thickness 9.35mm
    are required for use on direct circulation rotary well drilling rigs

    TECHNICAL SPECIFCATIN:

    The external upset drill pipe should be complete with alloy steel frication welded tool joints.
    These should be having box type connection at one end and pin type connection at other end
    these shall conform to 11312-part-I 1985 (latest).

    A. MATERIAL:

    1. The drill pipe shall be made from seamless tubing made from alloy steel equivalent to API
    SCT-N80 grade conforming or exceeding to IS grade "Yst 517".
    2. The tubing shall be either hot finished seamless conforming to general requirements of IS:
    1387-1987 (latest). The yield strength should be minimum 517 N/mm² and the tensile
    strength should be minimum 690 N/mm².
    3. The chemical composition of each lot is to be furnished by manufacture. The percentage of
    sulphur should be less than 0.06% and phosphorus should be less than 0.04% .
    4. The tool joint should be made of alloy steel conforming to Cr-I grade or EN-19 steel as
    specified in schedule IV of IS 1570-1961 (latest).

    B. DIMENSIONS:

    The raw tubing’s should conform to IS: 11312 (part-I) 1985 (latest). The dimensions &
    tolerances should be as under:-

    S .N. Particulars Dimension Tolerance


    1 Outside Diameter 88.9 mm ±0.75%
    2 Wall thickness 9.35 mm ±10%
    3 Length 6.096 mtr ±70 mm
    4 Nominal weight 19.8 kg/m +6.5% & - 3.5% for single
    length
    Tool Joint:

    5 Outside diameter of tool joint 120.65 mm ±0.79 mm

    6 General Tolerances ±5%

    C. TOOL JOINT:

    1. The drill pipe should be complete with alloy steel frication welded tool joints.
    2. The tool joints should be bucked on the drill rod with a minimum bucking torque of 10845
    Nm.
    3. The tool joint should be heat treated to minimum hardness of 285 BHN.
    4. The threads should conform to API 3½ IF . The box & pin connection should confirm to API
    3½ IF threads. Threads are to be checked by API approved gauges

    D. TESTS:

    The drill pipe should pass the following tests.

    1. Chemical Analysis as per section 9.1 of IS: 11312 (part-I) 1985.


    2. Dimensions test as per section 9.2.1 of IS: 11312 (part-I0 1985.
    3. Eccentricity test as per section 9.2.2.1 and 9.2.2.2 of IS: 11312 (part-I) 1985.
    4. Tensile strength, yield strength & percentage elongation as per section 9.3 of IS: 11312
    (part-I) 1985 by furnishing mill Test Certificate from the supplier of seamless tubes. The Mill
    Test Certificate should indicate tubing with heat nos. stenciled on tubes; the test certificate
    should also give the evidence about Tensile strength, Yield Strength, percentage (%)
    Elongation and Chemical Composition as proof of testing.
    5. The tool joints should have a minimum Yield strength of 517 N/mm², a minimum tensile
    strength of 690 N/mm² and elongation as per douse 9.3.1 (Table-3) of IS: 11312 (part-I)
    1985 (latest).

    You might also like