PROPOSAL

PENELITIAN KERJA SAMA INTERNASIONAL

( INISIASI )

LOW SPECIFIC ABSORPTION RATE (SAR) WEARABLE

RECONFIGURABLE ANTENNA DESIGN FOR 5G SYSTEM
APPLICATION

Oleh :

Ketua Peneliti : Dr. Bambang Setia Nugraha

Anggota Peneliti : Dr. Noor Asmawati Samsuri
: Dr. Levy Olivia Nur
: Harfan Hian Ryanu S.T., M.E.
: Alief Kusumaningtyas Krishnanti S.T

FAKULTAS TEKNIK ELEKTRO

UNIVERSITAS TELKOM
BANDUNG
MEI
2020

i
 HALAMAN PENGESAHAN PROPOSAL KERJASAMA INTERNASIONAL

1. Judul Penelitian Low Specific Absorption Rate (SAR) Wearable Reconfigurable

Antenna Design For 5G System Application
2. Ketua Peneliti / Pengusul Dr. Bambang Setia Nugraha
- Nama Bambang Setia Nugraha

- Telp / E-mail 0818614787

- NIK / NIDN 99760188-1/ 0429087601

- Jab. Fungsional / Struktural Lektor

- Bidang Keahlian Elektromagnetik, Antena dan Radar

- Jurusan / Fakultas Teknik Telekumunikasi/ FTE

3. Ang. Peneliti (Bd. Keahlian) 1. Dr. Noor Asmawati Samsuri (Antenna)

2. Dr. Levy Olivia Nur (Elektromagnetik dan Antena)
3. Harfan Hian Ryanu S.T., M.E. (Antenna)

4. Alief Kusumaningtyas Krishnanti S.T.

4. Jadwal Juni 2020- Juni 2021

5. Rencana Luaran 1. Publikasi Jurnal Internasional

6 Pembiayaan 1.

Bandung, 20 Mei 2020

Ketua Peneliti

Dr. Bambang Setia Nugroho

NIP. 99760035
Menyetujui
Bandung, 20 Mei 2020 Bandung, 20 Mei 2020
Ketua KK Transtel Dekan Fakultas Teknik Elektro

Dr. Nahcwan Mufti A Dr. Bambang Setia Nugroho

NIP. 99730017 NIP. 99760035
Bandung, 20 Mei 2020
Direktur PPM

Angga Rusdinar, Ph.D

NIP. 07740023

ii
 CONTENTS

CONTENTS .............................................................................................................................................. iii

EXECUTIVE SUMMARY ........................................................................................................................... iv

BAB 1 INTRODUCTION ....................................................................................................................... 5

1.1 Background ............................................................................................................................. 5

1.2 Research Objective ................................................................................................................. 6

1.3 Research Track Record ............................................................................................................ 6

1.4 Urgensi dan Kebaruan............................................................................................................. 6

1.5 Problem Statement ................................................................................................................. 6

1.6 Expected Outcome .................................................................................................................. 6

BAB 2 LITERATURE REVIEW ............................................................................................................... 7

BAB 3 METHODOLOGY ...................................................................................................................... 9

BAB 4 BUDGET, FACILITIES AND TIME SCHEDULE ........................................................................... 11

4.1 Budgetting ............................................................................................................................. 11

4.2 Time Schedule ....................................................................................................................... 11

DAFTAR PUSTAKA ................................................................................................................................. 12

LAMPIRAN ............................................................................................................................................. 14

iii
 EXECUTIVE SUMMARY

WBAN (Wireless Body Area Network) has gained increasing attention in recent years especially
for the implementation in medical application in continuous monitoring of human body condition. In
such system, several sensors collect and send the data to the hospital and health data center Several
concerns related to WBAN are the negative effects from the continuous exposure of the RF radiation
to the human body, the flexibility of the antenna within an erratic texture of human body without any
degradation in its performance. Furthermore, the increasing variety of services also demand an
antenna design that could also fulfill several different service standards.
This research will be focused on answering such mentioned aspect by designing a wearable slot-
ring antenna that is integrated with a metamaterial absorber to reduce the SAR. In order to increase
the complexity, the antenna will also be designed as frequency reconfigurable using PIN diode. Thus,
the designed antenna could fulfill several service standards. Firstly, the designed antenna will be
simulated and enhanced by using a computer software and then after that, the antenna will be
realized and the antenna performance will be measured.
The target outcome for this research are a publication within ISI indexed publisher or Q1/Q2
Scimago (Scopus) journal index publisher.

Keywords : WBAN Antenna, Reconfigurable, 5G Application, Metamaterial

iv
 BAB 1
INTRODUCTION
1.1 Background
WBAN (Wireless Body Area Network) has gained increasing attention in recent years especially
for the implementation in medical application in continuous monitoring of human body condition. In
such system, several sensors collect and send the data to the hospital and health data center [1].
However, one aspect that cannot be neglected is the negative effects from the continuous exposure
of the RF radiation to the human body. One of the main parameters to evaluate this condition is called
SAR (Specific Absorption Ration) and radiation efficiency from the sensor’s antenna [2]. Several
methods to optimize the antenna SAR have been researched, such as by using metamaterial absorber
[3]-[5], and artificial magnetic conductor (AMC) structures [6]-[7]. As a result of the implementation
of these metamaterial structures, the antenna could completely permeate the incident waves and
optimize the antenna SAR.
Besides of the drawback of the antenna radiation provided to the human body, another concern
of the WBAN antenna are the flexibility of the antenna itself. Human body has erratic texture
compared to fixed antenna aperture thus, antenna must be flexible enough to follow the texture of a
human body without any degradation in its performance. Some implementations that have been
reported is such as an antenna designed by using textile material for RFID application [8], and also
using paper [9]. Having said that specific implementation, the increasing variety of services also
demand an antenna design that could also fulfill several different service standards. For this purpose,
reconfigurable antenna is introduced within this research. Many researches have introduced an
antenna with frequency reconfigable [10], pattern reconfigurable [11], polarization reconfigurable
capability [12], or even a combination of two type of reconfigurability such as frequency and
polarization [13], or frequency and pattern reconfigurability [14]. The reconfigurability could be
achieved by employing switchable feeding networks or on-board switch such as PIN diode.
This research will be focused on designing a wearable slot-ring antenna that is integrated with
a metamaterial absorber to reduce the SAR. In order to increase the complexity, the antenna will also
be designed as frequency reconfigurable using PIN diode. Thus, the designed antenna could fulfill
several service standards. Firstly, the designed antenna will be simulated and enhanced by using a
computer software and then after that, the antenna will be realized and the antenna performance will
be measured.

5
1.2 Research Objective
The objectives of the proposed research are defined as follow:
1. To identify the influence of metamaterial absorber to the antenna system performance
regarding the RCS, and Specific Absorption Rate (SAR)
2. To determine the compatible reconfigurable technique that involves a structure of a
wearable scale slot ring antenna, and a metamaterial absorber
3. To identify the consistency of the resonant frequency of the antenna within an erratic
surface (wearable condition)

1.3 Research Track Record

This research is an iniciation collaborative research between Universiti Teknologi Malaysia and
Telkom University with an objective to improve the research quality for the academic staffs of Telkom
University. The research experience / track record of the research member could be seen in
attachment.

1.4 Urgensi dan Kebaruan

This antenna will be a pioneer that could be used in medical application as a sensor to be
attached inyo and monitor the human body. This research is the follow-up step from the visitation of
the UTM representative to Telkom University on February.

1.5 Problem Statement

In order to fulfill the safety standard grade devices for WBAN application, SAR reduction is an
important issue to be addressed, to ensure the device has no drawback effect to the human body.
Besides, the wearable size antenna demands an antenna that can work consistently within
everchanging textures. Lastly, a frequency reconfigurable antenna is expected so, the antenna could
operate within several service standards.

1.6 Expected Outcome

The target outcome for the proposed research are a publication within ISI indexed publisher or
Q1/Q2 Scimago (Scopus) journal index publisher.

6
 BAB 2
LITERATURE REVIEW
Slot ring microstrip antenna is one of hundred variety of a microstrip antenna that could
minimize the drawback of the standard microstrip antenna. By default, the bandwidth of a microstrip
antenna is very small. In order to widen the bandwidth of the antenna, a slot on the patch is needed.
Slot antenna utilizes inductive coupling between the feeding line and the slot. Higher inductive
coupling could widen the antenna bandwidth. According to [15]-[16], the resonant frequency (𝑓𝑟) of
a slot ring antenna is determined by
𝑐0
𝑓𝑟 = ;λ = 𝑝 = 4𝐿 (6.1)
λ𝑔 √𝜀𝑒𝑓𝑓 𝑔

Where λ𝑔 is the wavelength at the resonant frequency, 𝜀𝑒𝑓𝑓 is the effective dielectric constant
of the substrate, p is the perimeter of the slot ring, and L is the lateral length of the square slot ring.
On the other hand, reconfigurable antenna is an antenna system that could change the
frequency, pattern, and polarization, based on the service that is currently in use. Reconfigurability of
the antenna is achieved by implementing a switching mechanism that could change frequency,
polarization or direction pattern. In order to set the frequency reconfigurability of the antenna, two
perimeter and lateral length of the slot ring antenna needs to be determined. For the next step is the
positioning of the switch so the frequency could be changed depends on whether the switch is On or
Off.
The switch used in this research is a PIN diode. Pin diode is a semiconductor switch that is
operating as a variable resistor in a radio frequency range. The resistance value of the diode depends
on the bias of the diode. The advantage of utilizing a pin diode as a switch is its short voltage control,
its ability to handle on high power switching, its affordable price, and its high reliability. In a high
frequency, pin diode works within two condition: forward bias, and reverse bias.
In forward bias condition, diode is equivalent as a series combination of a resistor (Rs) and an
inductor (L). Rs is a function of the width of the intrinsic area (W) divided by the bias current (If), diode
lifetime (τ), and sum of the electron and hole movement within the diode (µn+µp), as defined as follow
[15]:
𝑊
𝑅𝑠 = I𝑓 .τ.(µ𝑛 +µ𝑝 )
(6.2)

In reverse bias condition, diode is equivalent as a parallel circuit consists of a capacitor (CT) and
a resistor (Rs), combined in series with an inductor (L). The capacitance value of the diode in a reverse
bias condition is defined as follow:
𝜀.𝐴
𝐶𝑇 = (6.3)
D

7
 Where CT is the capacitance value of the diode, while 𝜀 is the dielectric constant, A is the area
of the diode junction, and D is the thickness of the intrinsic area of the diode. [15]
In order to reduce the RCS, an electromagnetic absorber is utilized. Absorber is a device that
can be used to permeate incident electromagnetic wave, thus only a small portion or even none of
the wave is reflected back. Some of the applications of the absorber are used to reduce
electromagnetic interference, used in anechoic chambers, or for reducing RCS as mentioned earlier.
The absorber is designed by using a metamaterial structure. Metamaterial structure is a man-
made material which has a distinguished electromagnetic characteristic that cannot be found in the
nature [16]. Metamaterial structures are divided into several classes, such as:[17]
1. Double Negative (DNG) and Single Negative (SNG) Metamaterials: Almost all-natural material used
for electromagnetics have positive relative permeability (µr) and relative permittivity (εr). A
combination of material with negative permittivity and permeability (e.g gold and silver’s
permittivity at a short wavelength are negative) with other material could produce a new
metamaterial with negative µr and/or εr. DNG have both negative µr and εr resulting in a negative
refraction index, while SNG have either negative µr or εr, but not both.
2. Electronic Band Gap (EBG): Some of the frequency band in EBG structure does not support
Electromagnetic waves propagation, thus this metamaterial could be used to prevent a
propagation from a specific frequency.
3. Articial Magnetic Conductors (AMC): AMC has a high surface impedance within a certain frequency
range, thus could suppress a propagation of surface waves in certain frequency.

8
 BAB 3
METHODOLOGY
The antenna consists of two part: a slot ring antenna that operates in 5G frequency (3.5 GHz) at
the top and a dual ring metamaterial reflector at the bottom of the microstrip antenna. The slot ring
antenna will embedded with a PIN Diode to enable the frequency reconfigurability characteristic of
the antenna. To reduce the backward radiaton and SAR level, the dual ring metamaterial absorber is
present. The concept of proposed antenna design is illustrated in Fig. 1

(a) (b)
Fig.1 The concept of proposed antenna design. a) top view, b) bottom view

The proposed research consists of several step as described by table below:

No Step Activity Achievement Indicator
1 Literature Review for a Defining the problem A concept design of the
proposed issue and the statement and which wearable reconfigurable
antenna design parameter is measured to antenna with metamaterial
solve the problem absorber
2 Designing the antenna Determine the antenna The unoptimized antenna
dimension, feeding structure, and absorber dimension is
and absorber model & calculated, feeding
dimension structure, and the model of
the absorber is determined.
3 Simulation Simulate the calculated The optimized antenna
antenna dimension using a dimension is achieved,
computer software,
optimizing the dimension to
achieve desired output

9
 No Step Activity Achievement Indicator
4 Antenna realization and Realizing the optimum Antenna is realized and all
measurement dimension of the antenna relevant characteristics are
based on simulation and measured
measure all relevant
characteristics of the antenna.
5 Analyzing the result, and Analyzing the realized antenna Performance improvement
design improvement result and compare it with the of the designed antenna is
simulation result, improve the achieved
design of proposed antenna (if
necessary)
6 Preparing the publication Preparing publication on ISI Letter of Acceptance of the
Index or Q1/Q2 Scopus Index journal

This study will be divided into two years project. While the design and simulation process are
conducted in Telkom University as well as the antenna fabrication, the measurement will take place
at the UTM Malaysia.

10
 BAB 4  
BUDGET, FACILITIES AND TIME SCHEDULE 
4.1 Budgetting 
Tabel 4.1 Research Budget 

Item  Tahun 1  Tahun 2 

Honor  Tenaga  Penunjang,  bukan  Rp  5.000.000,‐ Rp  5.000.000,‐

dosen Peneliti (maksimum 20%) 

Bahan habis pakai dan peralatan  Rp 21.000.000,‐ Rp 21.000.000,‐

(maksimum 40%) 

Perjalanan (15%‐20%)  Rp  10.000.000,‐ Rp  10.000.000,‐

Lain‐lain termasuk registrasi publikasi  Rp. 15.000.000,‐ Rp. 15.000.000,‐

jurnal internasional, HKI, dll (20%) 

Total  Rp 51.000.000,‐ Rp 51.000.000,‐

4.2 Facility Provided By UTM 
In this research collaboration, UTM would help us in providing better antenna measurement 
tools such as Spectrum and Vector Network Analyzer, and guidance for better research output. 

4.3 Time Schedule 
Tabel 4.2 Rencana Jadwal Penelitian 

Semester 1  Semester 2  Semester 3  Semester 4 

Kegiatan 
1  2  3  4  5  6  1 2 3 4 5 6 1 2 3 4 5 6  1  2  3  4  5 6
Literature                                                 
Review  
Antenna                                                 
Design 
Simulation                           
Realization                 
and                                 
Measureme
nt 
Result                                                 
Analyzing 
Publication                           

11 
 
 DAFTAR PUSTAKA

[1] D. P. Tobn,, T. H. Falk and M. Maier, "Context awareness in WBANs: A survey on medical and
non-medical applications," IEEE Wireless Commun., vol. 20, no. 4, pp. 30-37, 2013.

[2] M. W. e. al., "Investigation of SAR Reduction Using Flexible Antenna With Metamaterial
Structure in Wireless Body Area Network.," IEEE Transactions on Antennas and Propagation, vol.
66, no. 6, pp. 3076-3086, June 2018.

[3] R. Junyi , G. Shuxi and J. Wen, "Low-RCS Monopolar Patch Antenna Based on a Dual-Ring
Metamaterial Absorber," IEEE Antennas and Wireless Propagation Letters, vol. 17, no. 1, pp. 102-
105, Jan. 2018.

[4] L. Tao, C. X, G. J, Z. Q, L. W and Y. H, "RCS Reduction of Waveguide Slot Antenna With

Metamaterial Absorber," IEEE Transactions on Antennas and Propagation, vol. 61, no. 3, pp.
1479-1484, 2013.

[5] Z. Yi, C. Xiangyu, G. Jun and L. Wen-Qiang, "Broadband RCS reduction and high gain waveguide
slot antenna with orthogonal array of polarisation-dependent AMC," Electronics Letters, vol. 49,
no. 21, pp. 1312-1313, 10 October 2013.

[6] Z. Jun, L. Jianxing and C. Juan, "Mutual Coupling Reduction of a Circularly Polarized Four-Element
Antenna Array Using Metamaterial Absorber for Unmanned Vehicles," IEEE Access, vol. 7, pp.
57469-57475, 2019.

[7] T. Liu, C. Zhou, X. He and Y. Yang, "A Low RCS Microstrip Antenna Based on Broadband AMC
Structures," in 2018 International Conference on Microwave and Millimeter Wave Technology
(ICMMT), Chengdu, 2018.

[8] M. Virili, H. Rogier, F. Alimenti and P. Mezzanote, "Wearable Textile Antenna Magnetically
Coupled to Flexible Active Electronic Circuits," IEEE Antennas and Wireless Propagation Letters,
vol. 13, pp. 209-212, 2014.

[9] B. S. C. a. A. Shamim., "Utilizing wideband AMC structures for high-gain inkjet-printed antennas
on lossy paper substrate,," IEEE Antenna Propagat. Lett., vol. 12, pp. 76-79, 2013.

[10] T. Li, H. Zhai, X. Wang, L. Li and C. Liang, "Frequency-Reconfigurable Bow-Tie Antenna for
Bluetooth, WiMAX, and WLAN Applications," IEEE Antennas and Wireless Propagation Letters,
vol. 14, pp. 171-174, 2015.

12
[11] G. Jin, M. Li, D. Liu and G. Zeng, "A Simple Planar Pattern-Reconfigurable Antenna Based on Arc
Dipoles," IEEE Antennas and Wireless Propagation Letters, vol. 17, no. 9, pp. 1664-1668, Sept.
2018.

[12] R. Lian, Z. Tang and Y. Yin, "Design of a Broadband Polarization-Reconfigurable Fabry–Perot

Resonator Antenna," IEEE Antennas and Wireless Propagation Letters, vol. 17, no. 1, pp. 122-
125, Jan. 2018.

[13] N. Nguyen-Trong, L. Hall and C. Fumeaux, "A Frequency- and Polarization-Reconfigurable Stub-
Loaded Microstrip Patch Antenna," IEEE Transactions on Antennas and Propagation, vol. 63, no.
11, pp. 5235-5240, Nov, 2015.

[14] N. Nguyen-Trong, L. Hall and C. Fumeaux, "A Frequency- and Pattern-Reconfigurable Center-
Shorted Microstrip Antenna," IEEE Antennas and Wireless Propagation Letter, vol. 15, pp. 1955-
1958, 2016.

[15] N. R. Team, "General Purpose PIN Diode BAP 51-02 Data Sheet," NXP Philips Corporation, Texas,
2008.

[16] H.-L. Y. X.-W. H. Y. a. D.-Y. H. M. Li, "Perfect metamaterial absorber with dual bands," Progress
in Electromagnetics Research, vol. 108, pp. 37-49, 2010.

[17] Bhattacharya. A., "Modeling and Simulation of Metamaterial-Based Devices for Industrial
Application Engineer," CST AG, Darmstadt, Germany.

13
 LAMPIRAN
BIODATA KETUA PENELITI
1 Nama Lengkap (dengan Dr. Bambang Setia Nugroho, ST., MT.
gelar)
2 Jabatan Fungsional Lektor
3 Jabatan Struktural -
4 NIP/NIK/No. Identitas 99760188-1
lainnya
5 NIDN 0429087601
6 Tempat dan Tanggal Bandung, 29 Agustus 1976
Lahir
7 Alamat Rumah Kompleks Griya Bukit Mas II Blok D3 No. 6, Jl. Bojongkoneng,
Bandung 40191
8 Nomor Telepon/Faks 022 7102436
9 Nomor HP 0818614787
10 Alamat Kantor Jl. Telekomunikasi no 1, Ters. Buah Batu, Bandung
11 Nomor Telepon/Faks 022-7564108, 022-7565933
12 Alamat e-mail [email protected]
[email protected]
13 Lulusan yang telah S-1 > 20 orang; S-2 = 1 orang; S-3 = 0 orang
dihasilkan
11. Mata Kuliah yg 1. Elektromagnetika I
diampu Elektromagnetika II
Antena dan Propagasi

B. RIWAYAT PENDIDIKAN
2.1 Program: S-1 S-2 S-3
2.2 Nama PT ITB ITB UI
2.3 Bidang Ilmu Teknik Elektro Teknik Elektro Teknik Elektro
2.4 Tahun Masuk 1994 2001 2009
2.5. Tahun Lulus 1999 2004 2015
2.6 Judul Simulasi kode-kode Performansi Teknik Desain dan
Skripsi/ Tesis/Disertasi konvolusional yang Transmit Diversity Dan Optimisasi Antena
dirangkai secara Space Time Coded Rekonfigurabel
serial, paralel, dan Modulation Untuk frekuensi berbasis
hibrid Mengurangi Efek slot
Multipath Fading Pada
Sistem Komunikasi
Wireless
2.7. Nama Pembim- Nana Rachmana, Dr. Ir. Sugihartono Prof. Ir. Eko Tjipto
bing/Promotor Meng Rahardjo, MSc.,
Ph.D.

14
C. PENGALAMAN PENELITIAN
Pendanaan
No. Tahun Judul Penelitian
Sumber Posisi
1 2011 Flexible Frequency Reconfigurable Antenna Hibah Pembantu
Untuk Aplikasi Software Defined Radio Tahun Kompetensi - peneliti
ke-2 Dikti
2 2010 Flexible Frequency Reconfigurable Antenna Hibah Pembantu
Untuk Aplikasi Software Defined Radio Kompetensi - peneliti
Dikti
2 2010 Phase Shifter Dengan Metode Butler Matrix 4 X Institut Teknologi Ketua Peneliti
4 Telkom
3 2010 Antena Array Mikrostrip Sebagai Komponen Institut Teknologi Pembantu
Dari Smart Antenna Untuk Aplikasi Wimax Telkom Peneliti

D. PENGALAMAN PENULISAN ARTIKEL ILMIAH

Volume/
No. Tahun Judul Artikel Ilmiah Nama Jurnal/Proceeding
Nomor
1 2014 Transmission-Line International Journal of Microwave
Analysis of Frequency Science and Technology, Volume 2014,
Reconfigurable Article ID 303581, 10 pages.
Rectangular-Ring http://dx.doi.org/10.1155/2014/303581
Microstrip Antenna , Hindawi Publishing Corporation.
Received 12/8/2014; Accepted
17/10/2014; Published 13/11/2014
Terindex Scopus dengan Impact Factor
(SJR) adalah 0,158 tahun 2013
2 2014 A Pattern
Reconfigurable of 2014 2nd International Conference on
Circular Short-Circuited Information and Communication
Patch Antenna Based on Technology (ICoICT)
Genetic Algorithm
3 2014 Planar Inverted-F
Antenna (PIFA) Array
with
Proceedings of ISAP 2014
Circular Polarization for
Nano Satellite
Application
4 2014 Dual-feed orthogonal
circular polarized
microstrip antenna with Proceedings of ISAP 2014
front-end parasitic
for Inter Satellite Link

15
5 2013 Multiband Proceedings of Asia Pacific Conference
Reconfigurable on Antenna and Propagation (APCAP
Microstrip Antenna 2013)
6 2013 Faculty assessment
system with collective
2013 IEEE International Conference on
collegial leadership
Teaching, Assessment and Learning for
approach for increasing
Engineering (TALE)
academic and research
culture progressively
7 2013 Ultra Wideband Planar
Proceeding of International Conference
Triangular Patch
of Information and Communication
Antenna with Slit Ridged
Technology (ICoICT 2013)
Ground Plane
8 2012 Kajian Teknis Penerapan
Sharing Infrastruktur
GSM dan UMTS Antar
ISSN: No. Prosiding Seminar Nasional Ilmu
Operator Jaringan
2303-0798 Pengetahuan Teknik 2012
Komunikasi Bergerak
(Studi Kasus: Jawa
Barat)
9 2012 Perancangan dan
Realisasi Antena Program Book Seminar Nasional
Mikrostrip Sierpinski Microwave Antena dan Propagasi
Carpet Dual Band Pada (SMAP 2012)
Pita Frekuensi ISM
10 2012 PIN Diodes Slotted
Proceedings of The 2012 International
Microstrip Antenna as
Symposium on Antenna and
Frequency
Propagation (ISAP2012)
Reconfigurable Antenna
11 2011 Simple Frequency
Reconfigurable Antenna
ISSN: No. 14- Proceeding of The 12th International
by Changing the
1284 Conference on QiR (Quality in Research)
Number and Position
of the Switches
12 2009 Pemecahan Integral
Juni 2009,
Pocklington
Volume 14 –
Menggunakan Metoda Jurnal Penelitian dan Pengembangan
Nomor 1
Momen untuk Telekomunikasi
ISSN: No.
Menentukan Besaran
1410-7066
Antena Batang
13 2008 The Comparison of Volume 13 -
Channel Capacity Nomor 1,
Between Known and Juni 2008
Jurnal Penelitian dan Pengembangan
Unknown Channel ISSN : 1410 -
Telekomunikasi
Characteristic Receiver 7066
in MIMO Spatial Akreditasi :
Multiplexing OFDM No.

16
 48/DIKTI/Ke
p/2006
14 2008 Performance of
Transmit Diversity
Technique and Space
Proceedings International Conference
Time Coded Modulation ISSN : 1858-
on Telecommunication (ICTel 2008),
to Reduce Multipath 2982
Bandung, 19 - 21 Agustus 2008
Fading Effect on
Wireless
Communication System
15 2008 Analysis on The Effect of
Imperfect Power Proceedings International Conference
ISSN : 1858-
Control in The Capacity on Telecommunication (ICTel 2008),
2982
of DS-CDMA Cellular Bandung, 19 - 21 Agustus 2008
System

E. Karya Buku dalam 5 Tahun Terakhir

No Judul Buku Tahun Jumlah Halaman Penerbit

1
2
3
Dst.

F. Perolehan HKI dalam 5–10 Tahun Terakhir

No. Judul/Tema HKI Tahun Jenis Nomor P/ID

1
2
3
Dst.

I. Pengalaman Merumuskan Kebijakan Publik/Rekayasa Sosial Lainnya dalam 5

TahunTerakhir
Judul/Tema/Jenis Rekayasa Sosial Lainnya yang Tempat Respon
No. Tahun
Telah Diterapkan Penerapa Masyarakat
1
2
3
Dst.

17
J. Penghargaan dalam 10 tahun Terakhir (dari pemerintah, asosiasi atauinstitusi
lainnya)

No. Jenis Penghargaan Institusi Pemberi Penghargaan Tahun

1
2
3
Dst.

Semua data yang saya isikan dan tercantum dalam biodata ini adalah benar dan dapat
dipertanggung jawabkan secara hukum. Apabila dikemudian hari ternyata dijumpai ketidaksesuaian
dengan kenyataan, saya sanggup menerima sanksi. Demikian biodata ini saya buat dengan
sebenarnya untuk memenuhi salah satu persyaratan dalam pengajuan Proposal Kerja sama
Internasional Telkom Unversity.
Bandung, 20 Mei 2020
Pengusul,

Dr. Bambang Setia Nugroho, ST., MT.

NIP. 99760188-1

18
 BIODATA ANGGOTA

A. Identitas Diri
1 Nama Lengkap (dengan gelar) Dr. Levy Olivia Nur, ST. MT.
2 Jenis Kelamin Perempuan
3 Jabatan Fungsional Lektor
4 NIP/NIK/Identitas lainnya 14780033
5 NIDN 0412067804
6 Tempat dan Tanggal Lahir Bandung 12 Juni 1978
7 E-mail [email protected]
[email protected]
8 Nomor Telepon/HP 081220421233
9 Alamat Kantor Jl. Telekomunikasi No 1, Terusan Buah Batu
10 Nomor Telepon/Faks (022)7564108/ (022) 7565 930
11 Lulusan yang Telah Dihasilkan S-1 = 60 orang; S-2 = 2 orang; S-3 = - orang
Elektromagnetika
Elektromagnetika Telekomunikasi
12. Mata Kuliah yg Diampu
Antena dan Propagasi
Dasar Telekomunikasi
Sistem Komunikasi

B. Riwayat Pendidikan
S-1 S-2 S-3
Nama Perguruan Tinggi ITB ITB ITB
Bidang Ilmu Teknik Elektro Teknik Elektro Teknik Elektro
Tahun Masuk-Lulus 1996-2001 2001-2004 2009-2014
Judul Skripsi/Tesis/Disertasi Pengukuran Space Time Block Perancangan dan
Propagasi GSM Code untuk Fabrikasi
900MHz untuk komunikasi Penyerap
Skenario wireless Gelombang
Microcell Elektromagnetik
berbasis
Permukaan
Bertekstur
Nama Pembimbing/Promotor Dr, Utoro S. Dr. Sugihartono Prof. Adit
Kurniawan, Dr
Sugihartono, Dr.
Achmad Munir
C. Pengalaman Penelitian
(Bukan Skripsi, Tesis, maupun Disertasi)
Pendanaan
Judul Penelitian Keterangan
No. Tahun Sumber*

2012 Rancang Bangun Material Antideteksi Radar INSinas, Ketua

1 Berbasis Teknologi Texture Surface untuk Kemenristek
Platform Kendaraan Tempur

2013 Rancang Bangun Material Antideteksi Radar INSinas, Ketua

2 Berbasis Teknologi Texture Surface untuk Kemenristek
Platform Kendaraan Tempur
3 2016 Studi Komparasi Artificial Magnetic Internal Ketua
Conductor untuk Aplikasi Kesehatan

4 2016 Penggunaan Metoda Problem Based Learning Internal Ketua

pada Mata Kuliah Antena Propagasi

5 2017 Rancang Bangun Penyerap Gelombang Penelitian, Anggota

Mikro yang Dapat Dipakai untuk Aplikasi Produk Terapan
Kesehatan Ristek Dikti

6 2017 Analisis Pengaruh Jarak Antar Antena Internal Ketua

terhadap Mutual Coupling di Sistem Antena
Massive MIMO pada Frekuensi Kandidat 5G
7 2017 Perbandingan Metoda Pengukuran Nilai Internal Ketua
Permitivitas Bahan Tekstil Menggunakan
Saluran Transmisi dan Antena Mikrostrip
untuk Aplikasi Kesehatan
8 2017 Alat Pendeteksi Konfigurasi Sinyal Otak Insentif Riset Anggota
Akibat Kekerasan Seksual pada Anak SINAS

9 2018 Rancang Bangun Penyerap Gelombang Penelitian, Anggota

Mikro yang Dapat Dipakai untuk Aplikasi Produk Terapan
Kesehatan Ristek Dikti
(Tahun ke-2)
10 2018 Alat Pendeteksi Konfigurasi Sinyal Otak Insentif Riset Anggota
Akibat Kekerasan Seksual pada Anak SINAS (Tahun
ke-2)
11 2018 5G-POINT: Preparing Optimal 5G Indonesia INSINAS Anggota
Networks

12 2019 Pengembangan Wearable Device untuk Penelitian Dasar Ketua

Aplikasi Pemantau Kesehatan Unggulan
 Perguruan Tinggi
Kemeristek Dikti

13 2019 Pengembangan Wearable Device untuk Penelitian Dasar Ketua

Aplikasi Pemantau Kesehatan (Lanjutan) Unggulan
Perguruan Tinggi
Kemeristek Dikti

* Tuliskan sumber pendanaan baik dari skema penelitian DIKTI maupun dari
sumber lainnya.

D. Pengalaman Pengabdian Kepada Masyarakat

Pendanaan
No. Tahun Judul Pengabdian Kepada Masyarakat
Sumber* Jml (Juta Rp)
1 2011 Pembangkit Listrik Tenaga Mikro Hidro IT Telkom
Perhutani
2 2011 Pelatihan Mikrokontroler IT Telkom
3 2018 Pelatihan Pembuatan Modul Praktikum PPM 7
Telkom
• Tuliskan sumber pendanaan baik dari skema pengabdian kepada masyarakat
DIKTI maupun dari sumber lainnya.

E. Publikasi Artikel Ilmiah Dalam Jurnal

Volume/
No. Judul Artikel Ilmiah Nama Jurnal Nomor/Ta
hun
1 Rectangular to Parallel Plate Waveguide International Journal of Volume 6/
Transition and Its Tapering Effect for Electrical Engineering and Number
Microwave Devices Characterization Informatics (IJEEI) 1/2014
2. Theoretical Analysis of Resonant International Journal of Volume
Frequency for AMC-based Absorber Electrical Engineering and 7/Number
Composed of Square Patch Array Informatics (IJEEI) II/2015
3 Perancangan dan Pabrikasi Penyerap Jurnal Penelitian dan Vol 1; ISSN:
Gelombang Elektromagnetik Patch Segi Pengembangan 2502-2105;
Enam Berbasis Surface Textured Telekomunikasi, Kendali, Januari 2016,
Komputer, Elektrik, dan Bandung
Elektronika (TEKTRIKA)
 4 Perancangan Antena MIMO 2×2 Array Jurnal Nasional Teknik Vol. 6, No. 1,
Rectangular Patch dengan U-Slot untuk Elektro dan Teknologi Februari
Aplikasi 5G Informasi (JNTETI) 2017

5 Pengembangan Antena Fleksibel Microstrip TELKA UIN Sunan Gunung Vol.5, No. 2,
Bowtie Jati 2019

F. Pemakalah Seminar Ilmiah (Oral Presentation)

Nama Pertemuan Ilmiah Waktu dan
No Judul Artikel Ilmiah
/Seminar Tempat
1 PIERS 2010 Characterization of Microwave Thin Juli 2010,
Radar Absorber Composed of Cambrige, USA
Hexagonal Patch Array
2 AUTOLE 2010 Varactor Tunable Diode of November 2010,
Microwave Thin Radar Absorber Bandung, Indonesia
Composed of Hexagonal Patch
Array
3 FORTEI 2012 Karakterisasi Bentuk Absorber 20-22 September
berdasarkan Teknik Tekstur Surface 2012, UI, Depok
Indonesia
4 IEEE International Characterization of Radar Absorber 23 November 2012,
Symposium on Radio based on Square Textured Surface Singapore
Frequency Integration
Technology RFIT2012
5 INSinas, Kemenristek Rancang Bangun Material 29-30 November
Antideteksi Radar Berbasis 2012
Teknologi Texture Surface untuk
Platform Kendaraan Tempur
6. ICoICT2015 Thin EM Wave Absorber Composed Mei 2015
of Octagonal
Patch Array and Its Characteristic
Measurement
7. ICoICT 2015 Bandwidth Improvement of Square Mei 2015
Patch
Array-based AMC Using Multiple
Slots Technique
8 SENIATI 2017 Perancangan Antena Array 1×2 Februari 2017
Rectangular Patch dengan U-Slot
untuk Aplikasi 5G
9 TSSA 2017 Spiral-shaped Printed Planar Oktober 2017
Inverted-F Antenna for Body
Wearable Application
 10 PIERS 2017 Experimental Study on Textile November 2017
Properties for Wearable Absorber
Using Cavity Method
11 PIERS 2018 Flexible Artificial Magnetic Conductor Agustus 2018
Reflector for Wearable Antenna
Application

12 PIERS 2018 Thin EM Wave Absorber Metasurface Agustus 2018

Based on Artificial Magnetic
Conductor

13 ISAP 2018 Development of Bendable Antenna Sept 2018

Reflector Based on Artificial Magnetic
Conductor
14 APWIMOB 2019 Design of Circular Modified UWB November 2019
Antenna Microstrip for Brain Cancer
Detection”

H. Perolehan HKI dalam 5–10 Tahun Terakhir

No. Judul/Tema HKI Tahun Jenis Nomor P/ID
1 Program Komputer “Aplikasi P-Brain” 2017 Aplikasi M.01-HC.03.01
2
Dst.

Semua data yang saya isikan dan tercantum dalam biodata ini adalah benar dan dapat
dipertanggungjawabkan secara hukum. Apabila di kemudian hari ternyata dijumpai
ketidak-sesuaian dengan kenyataan, saya sanggup menerima sanksi.

Bandung, 11 Juni 2020

Pengusul

(Dr. Levy Olivia Nur, MT)

 BIODATA ANGGOTA PENELITI II
1 Nama Lengkap (dengan gelar) Harfan Hian Ryanu S.T., M.E.,
2 Jenis Kelamin Laki-Laki
3 Jabatan Fungsional NJFA2
4 NIP/NIK/Identitas lainnya 20900008-3
5 NIDN 0407029001
6 Tempat dan Tanggal Lahir Jakarta, 7 Februari 1990
7 E-mail [email protected]

9 Nomor Telepon/HP 081382187713

10 Alamat Kantor Jl. Telekomunikasi no 1, Ters. Buah Batu, Bandung
11 Nomor Telepon/Faks -
12 Lulusan yang Telah Dihasilkan S-1 = 0 orang; S-2 = 0 orang; S-3 = 0 orang
1. Elektromagnetika (FEH2F3)
2. Mikroprosesor (TTH2D3)
13. Mata Kuliah yg Diampu

B. Riwayat Pendidikan
S-1 S-2 S-3
Nama Perguruan Tinggi IT Telkom University of Sydney -
Bidang Ilmu Teknik Teknik -
Telekomunikasi Telekomunikasi
Tahun Masuk-Lulus 2007-2011 2017-2018 -
Judul Skripsi/Tesis/Disertasi Perancangan Dan Implementation of -
Realisasi Antena Multiple USRP in
Microstrip Open Cellular
Reconfigurable Technology Platform
Pada Dua Frekuensi
Kerja
Nama Pembimbing/Promotor Dr. Bambang Setia Dr Wibowo -
Nugroho Hardjawana

24
 C. Pengalaman Penelitian
(Bukan Skripsi, Tesis, maupun Disertasi)
Pendanaan
No. Tahun Judul Penelitian Keterangan
Sumber*
1

* Tuliskan sumber pendanaan baik dari skema penelitian DIKTI maupun dari sumber
lainnya.

D. Pengalaman Pengabdian Kepada Masyarakat

Pendanaan
No. Tahun Judul Pengabdian Kepada Masyarakat
Sumber* Jml (Juta Rp)
1
• Tuliskan sumber pendanaan baik dari skema pengabdian kepada masyarakat DIKTI
maupun dari sumber lainnya.

E. Publikasi Artikel Ilmiah Dalam Jurnal

Volume/
No. Judul Artikel Ilmiah Nama Jurnal Nomor/Tah
un
1

F. Pemakalah Seminar Ilmiah (Oral Presentation)

Nama Pertemuan Ilmiah Waktu dan
No Judul Artikel Ilmiah
/Seminar Tempat
1

G. Karya Buku dalam 5 Tahun Terakhir

Jumlah
No Judul Buku Tahun Penerbit
Halaman
1
2
Dst.

I. Perolehan HKI dalam 5–10 Tahun Terakhir

No. Judul/Tema HKI Tahun Jenis Nomor P/ID

1
Dst.

I. Pengalaman Merumuskan Kebijakan Publik/Rekayasa Sosial Lainnya dalam 5

Tahun Terakhir

25
 Judul/Tema/Jenis Rekayasa Sosial Lainnya yang Tempat Respon
No. Tahun
Telah Diterapkan Penerapan Masyarakat
1
2
Dst.

J. Penghargaan dalam 10 tahun Terakhir (dari pemerintah, asosiasi atau institusi lainnya)
Institusi Pemberi
No. Jenis Penghargaan Tahun
Penghargaan
1 “The Most Contributing Awardee” Awards in PK-67 LPDP 2016
2
Dst.

Semua data yang saya isikan dan tercantum dalam biodata ini adalah benar dan dapat
dipertanggungjawabkan secara hukum. Apabila di kemudian hari ternyata dijumpai ketidak-sesuaian
dengan kenyataan, saya sanggup menerima sanksi.

Demikian biodata ini saya buat dengan sebenarnya untuk memenuhi salah satu persyaratan dalam
pengajuan Proposal Kerja sama Internasional

Bandung, 20 Mei 2020

Pengusul

(Harfan Hian Ryanu S.T., M.E.)

26
 SURAT PERNYATAAN KETUA PENELITI

Yang bertandatangan di bawah ini:

Nama : Dr. Bambang Setia Nugroho, S.T., M.T.
NIP/NIDN : 99760035
Prodi : S1 Teknik Telekomunikasi
Jabatan Fungsional : Lektor
Dengan ini menyatakan bahwa proposal penelitian saya dengan judul :
LOW SPECIFIC ABSORPTION RATE (SAR) WEARABLE RECONFIGURABLE ANTENNA DESIGN FOR 5G
SYSTEM APPLICATION

yang saya usulkan dalam Skema Penelitian Kerja sama Internasional untuk tahun anggaran 2020
bersifat original dan belum pernah dibiayai oleh lembaga / sumber dana lain.

Bilamana dikemudian hari ditemukan ketidaksesuaian dengan pernyataan ini, maka saya bersedia
dituntut dan diproses sesuai dengan ketentuan yang berlaku dan mengembalikan seluruh biaya
penelitian yang sudah diterima ke Universitas Telkom.

Demikian pernyataan ini dibuat dengan sesungguhnya dan dengan sebenar-benarnya.

Bandung, 20 Mei 2020

Mengetahui, Yang Menyatakan,
Direktur Penelitian dan Pengabdian Masyarakat

Angga Rusdinar, Ph.D Dr. Bambang Setia Nugroho, S.T., M.T.

NIP. 07740023 NIP. 99760035

27
Lampiran 6.4 Biodata Peneliti Mitra Internasional

▪ Nama : Noor Asmawati Binti Samsuri

▪ Institusi : Sekolah Kejuruteraan Elektrik, Universiti Teknologi Malaysia
▪ Bidang : Wearable/Flexible antenna, Specific Absorption Rate, Telemetry antenna for
medical/monitoring application, EMF-Human body interaction

Daftar Publikasi:
JOURNAL
a) Mohd Ezwan B. Jalil, Mohamad Kamal A. Rahim, Osman B. Ayop, Noor Asmawati Samsuri,
“Size miniaturization of chipless RFID tag using metamaterial structure”, Indonesian Journal
of Electrical Engineering and Computer Science, Vol.15, No.2, 2019.
b) N. H. Sulaiman, N. A. Samsuri, M. K. A. Rahim, F. C. Seman, M. Inam, ' Compact Meander
Line Telemetry Antenna for Implantable Pacemaker Applications', Indonesian Journal of
Electrical Engineering and Computer Science, Vol. 10, No. 3, June 2018, pp.883-889, ISSN:
2502-4752.
c) N. Othman, N. A. Samsuri, M. K. A. Rahim, K. Kamardin, H. A. Majid,' Meander bowtie
Antenna for Wearable Application', Telecommunication, Computing, Electronics and Control
(TELKOMNIKA), Vol. 16, No. 4, 2018.
d) O. Ayop, MKA Rahim, NA Murad, NA Samsuri, F Zubir, HA Majid, 'Dual-band metamaterial
perfect absorber with nearly polarization-independent' Applied Physics A, Vol 123 (1), 63, Jan
2017 (IF 1.7 - Q3)
e) ME Jalil, MKA Rahim, NA Samsuri, R Dewan, K Kamardin, 'Flexible ultra-wideband antenna
incorporated with metamaterial structures: multiple notches for chipless RFID application'
Applied Physic A, Vol 123 (1), 48, Jan 2017 (IF 1.7 - Q3)
f) Dewan, R., Rahim, M. K. A., Hamid, M. R., Yusoff, M. F. M., Samsuri, N. A., Murad, N. A. &
Kamardin, K, „ Artificial Magnetic Conductor for various application: An Overview‟,
International Journal of RF and Microwave Computer-Aided Engineering, 2017 (Q3)
g) N. H. Sulaiman, N. A. Samsuri, M. K. A. Rahim, F. C. Seman, M. Inam, „Design and Analysis
of Optimum Performance Pacemaker Telemetry Antenna‟, Telecommunication, Computing,
Electronics and Control (TELKOMNIKA) Vol 15, No 2, 2017 (SCOPUS)
h) N. J. Ramly, M. K. A. Rahim, N. A. Samsuri, H. A. Majid, „Embroidery leaf shape dipole
antenna performance and characterization, International Journal of Electrical and Computer
Engineering (IJECE), Vol. 7, No. 3 June 2017 (SCOPUS)
i) N. A. Elias, N. A. Samsuri, M. K. A. Rahim, C. J. Panagamuwa, W. Whittow, „SAR levels for
irradiation by a crumpled 900 MHz Flexible diamond dipole‟ International Journal of Electrical
and Computer Engineering (IJECE), Vol. 7, No. 3 June 2017 (SCOPUS)
j) M.S.Zainuddin, M.K.A.Rahim, N.A.Samsuri, H.A. Majid, „RF Energy harvesting study using
various metamaterial patch structure‟ International Journal of Electrical and Computer
Engineering (IJECE), Vol. 7, No. 3 June 2017 (SCOPUS)
k) N. Othman, N. A. Samsuri, M. K. A. Rahim, K. Kamardin - Design and analysis of flexible bow-
tie antenna for medical application - ELEKTRIKA, 2017
l) S. Z. N. Zool Ambia, N. A. Samsuri - Anti-Theft Motorcycle Alarm System Using GSM and
GPS - ELEKTRIKA, 2017
m) Osman Ayop, Mohamad Kamal A Rahim, Noor Asniza Murad and Noor Asmawati Samsuri,
"Dual-resonant polarization-independent and wide-angle metamaterial absorber in X-band
frequency", Applied Physics A , 2016 (IF 1.70 - Q2).
n) Osman Ayop, Mohamad Kamal A Rahim, Noor Asniza Murad, Noor Asmawati Samsuri,
"Wideband polarization-insensitive metamaterial absorber with perfect dual resonances",
Applied Physics A 2016 (IF 1.70 - Q2)
o) M.E.Jalil, M.K.A.Rahim, N.A.Samsuri and R Dewan, "Flexible printed chipless RFID tag using
metamaterial–split ring resonator", Applied Physics A, 2016 (IF 1.70 - Q2)
p) H.A. Majid, M.K.A.Rahim, M.R.Hamid, N.A.Murad, N.A. Samsuri, M.F.M.Yusof and
M.R.Kamaruddin, ' Band-notched reconfigurable CPW-fed UWB antenna', Applied Physics A,
2016 (IF 1.70 - Q2)
q) K. Kamardin, M.K.A.Rahim, P.s.Hall, N.A Samsuri, T.A Latif, M.H.Ullah, 'Planar textile
antennas with artificial magnetic conductor for body-centric communications", Applied Physics
A, 2016 (IF 1.70 - Q2)
r) Kamilia Kamardin, Mohamad Kamal A Rahim, Peter S. Hall, Noor Asmawati Samsuri, Tarik
Abdul latef and Mohammad Habib Ullah , „Textile artificial magnetic conductor jacket for
transmission enhancement between antennas under bending and wetness measurements‟
Applied Physics A, April 2016 (IF 1.70 - Q2).
s) Kamilia Kamardin, Mohamad Kamal A.Rahim, Noor Asmawati Samsuri, Mohd Ezwan Jalil,
Salwani Mohd Daud, Suriani Mohd Sam, Noor Azurati Ahmad, 'Textile diamond dipole for
body centric communications at 2.4 GHz and 5.8 GHz",ARPN Journal of Engineering and
Sciences, Vol 11, No 12, pp 7877 - 7882, June 2016 (SCOPUS).
t) Kamilia Kamardin, Mohamad Kamal A.Rahim, Noor Asmawati Samsuri, Mohd Ezwan Jalil,
Siti Sophiayti Yuhania, Mohd Nazri Kama, Othman Mohd Yusof, 'A parametric study of Textile
Artificial magnetic Conductor with wire dipole', ARPN Journal of Engineering and Sciences,
Vol 11, No 12, pp 7888 - 7893, June 2016 (SCOPUS).
u) Norfatin Akma Elias, Noor Asmawati Samsuri, Mohamad Kamal A Rahim, Chintana
Panagamuwa, Will Whittow "Bending and Crumpling Deformation Study of the Resonant
Characteristic and SAR for a 2.4 GHz Textile Antenna", Jurnal Teknologi Special Edition on
Antenna and Propagation, Volume 77, Issue 10, 2015, pp 17-23
v) Nazirah Othman, Noor Asmawati Samsuri, Mohamad Kamal A Rahim, "Estimation of Specific
Absorption rate in the Human Leg and Testicle due to a Metallic Ring", Jurnal Teknologi
Special Edition on Antenna and Propagation, Volume 77, Issue 10, 2015, pp 85-90
w) Mohd Ezwan Bin Jalil, Mohammad Kamal A. Rahim, Noor Asmawati Samsuri, Raimi Dewan,
" Multi-resonator Using Complementary Split Ring Resonator for Chip-Less RFID Application",
Theory and Applications of Applied Electromagnetics Lecture Notes in Electrical Engineering,
Volume 344, 2015, pp 215-221
x) Osman Ayop, Mohamad Kamal A. Rahim, Noor Asniza Murad, Noor Asmawati Samsuri, "
Double Layer Polarization Insensitive Metamaterial Absorber with Dual Resonances", Theory
and Applications of Applied Electromagnetics Lecture Notes in Electrical Engineering, Volume
344, 2015, pp 231-238
y) R. Dewan, M. K. A. Rahim, M. R. Hamid, N. A. Samsuri, M. F. M. Yusoff, B. D. Bala, M. E.
Jalil, "Dual Band Stacked Artificial Magnetic Conductor with Dipole Antenna", Theory and
Applications of Applied Electromagnetics Lecture Notes in Electrical Engineering, Volume
344, 2015, pp 197-205
z) N. A. Elias, N. A. Samsuri, M. K. A. Rahim, "Analytical Study of Energy Absorption in Human
Body Due to Bendable Behaviour of Textile Antenna", Theory and Applications of Applied
Electromagnetics Lecture Notes in Electrical Engineering, Volume 344, 2015, pp 329-337
aa) K. Kamardin, M.K.A. Rahim, P.S. Hall, N.A. Samsuri, " Vertical and horizontal transmission
enhancement between antennas using textile artificial magnetic conductor waveguide sheet",
Electronics Letters, 30th April 2015, Vol. 51, No. 9, pp. 671 – 673
bb) H.A.Majid, M. K. A. Rahim, M. R. Hamid, N.A.Samsuri, N.A.Murad, M.F.M.Yusof and O. Ayop,
'Reconfigurable Notched Wideband Antenna Using EBG Structure' Microwave Optical
Technology Letter, Vol 57, Issue 2, pp 497-501, Feb 2015 (IF=0.618)
cc) Kamilia Kamardin, Mohamad Kamal A Rahim, Noor Asmawati Samsuri, 'Transmission
Enhancement using Textile Artificial Magnetic Conductor with Co-planar Waveguide
Monopole Antenna' Microwave optical technology letter, Vol 57 Issue 1, pp 197-200, 2015 (IF
0.618)
dd) Mohd E.Jalil, Mohamad K.A.Rahim, Nurul J Ramly, Noor A Samsuri, Kamilia Kamardin, Mohd
A Abdullah, Huda A Majid "Planar Textile antenna for body centric wireless communication
system", Progress in Electromagnetic Research C (PIERC), Vol 54, 29-40, 2014 (Index
Scopus)
 ee) Nur Hidayah Ramli, Muhammad Ramlee Kamarudin, Ezla Najwa Ahyat, Nor Asmawati
Samsuri, Nor Hisham H. Khamis, A. Y. Abdulrahman and Muhammad Fitri Ayob, "Comparison
of performance of compact ring printed monopole and loop antennas for wireless-implantable
body area network applications", Microwave and Optical Technology Letters, Vol. 56, No. 6,
June 2014.
ff) Nur H. Ramli, Muhammad R. Kamarudin, Noor A. Samsuri, Ezla N. Ahyat, Amuda Y.
Abdulrahman and Mohd F. Jamlos, " A 6.0GHz Small Printed Monopole Antenna for Wirelss
Implantable Body Area Network Applications" Progress In Electromagnetics Research C, Vol.
41, pp 189-200, 2013.
gg) Mohd E. Jalil, Mohamad K. A. Rahim, Noor A. Samsuri, Noor A. Murad, Huda A. Majid, Kamilia
Kamardin, and Muhamad A. Abdullah, "Fractal Koch Multiband Textile Antenna Performance
with Bending, Wet Conditions and on the Human Body", Progress In Electromagnetics
Research, Vol. 140, 633-652, 2013.
hh) Mohsen Khalily, Mohamad Kamal A. Rahim, Norasniza A Murad, Noor Asmawati Samsuri,
and Ahmed A. Kishk, "Rectangular Ring-Shaped Dielectric Resonator Antenna for Dual and
Wideband Frequency", Microwave and Optical Technology Letters, Vol. 55, No. 5, May 2013.
ii) Nur Hidayah Ramli, Muhammad Ramlee Kamarudin, Noor Asmawati Samsuri, and Ezla
Najwa Ahyat, " Investigation on a compact ring printed monopole antenna for wireless
implantable body area network (WiBAN) applications", Microwave and Optical Technology
Letters, Vol. 55, No. 5, May 2013.
jj) Mai A. R. Osman, M. K. A. Rahim, N. Asmawati Samsuri, M. K. Elbasheer and Mohammed
E. Ali, "Textile UWB Antenna Bending and Wet Performances", International Journal of
Antennas and Propagation, (IF: 0.468), Mar 2012.

PROCEEDING/CONFERENCES
a) N H Sulaiman, N A Samsuri, M K A Rahim, M Inam, F C Seman and N Othman, “Phantom
Development for In-Vitro Measurements of MICS Band Telemetry Antenna”, International
Conference on Telecommunication, Electronic and Computer Engineering (ICTEC 2019),
2019.
b) N. Othman, N. A. Samsuri, M. K. A. Rahim, and N. H. Sulaiman, “Water Ageing Effect on
Wearable Antenna Made of Medical-friendly and Transdermal Material at 2.4 GHz”,
International Conference on Telecommunication, Electronic and Computer Engineering
(ICTEC 2019), 2019.
c) MKA Rahim, MR Hamid, NA Samsuri, NA Murad, F Zubir, O Ayop, MFM Yusof, HA Majid,
“Antenna with Artificial Magnetic Conductor for Wireless Application’, IEEE Asia-Pacific
Conference on Applied Electromagnetics (APACE), pp. 1-5, 2019.
d) Nurul Jannah Ramly, Mohamad Kamal A Rahim, Noor Asmawati Samsuri, Mohd Fairus Mohd
Yusoff, Muhammad Faizal Ismail, Huda A Majid, “Leaf-Shaped Textile Dipole Antenna
Design”, IEEE Conference on Antenna Measurements & Applications (CAMA), pp. 188-190,
Oct. 2019.
e) Adamu Y Iliyasu, Mohamad Rijal Bin Hamid, Mohamad Kamal A Rahim, Noor Asmawati
Samsuri, Mohd Fairus Bin Mohd Yusoff, “Multi-band Frequency Reconfigurable Metamaterial
Antenna Design”, 10th International Conference on Robotics, Vision, Signal Processing and
Power Applications, pp. 425-431, 2019.
f) Murtala Aminu-Baba, Mohammad Kamal A Rahim, Farid Zubir, Mohd Fairus Mohd Yusoff,
Noor Asmawati Samsuri, “Wideband Monopole Antenna with Rotational Circular SRR”, 10th
International Conference on Robotics, Vision, Signal Processing and Power Applications, pp.
419-424, 2019.
g) MKA Rahim ; MR Hamid ; NA Samsuri ; NA Murad ; F Zubir ; O Ayop ; MFM Yusof ; HA Majid
, “Antenna with Artificial Magnetic Conductor for Wireless Application”, IEEE Asia-Pacific
Conference on Applied Electromagnetics (APACE), 2019.
h) NH Sulaiman, NA Samsuri, MKA Rahim, MI Abbasi, FC Seman, "Low Profile Compact
Meander Line Antenna for Pacemaker Applications in MICS Band", 2018 IEEE 7th Asia-
Pacific Conference on Antenna and Propagation, Auckland, New Zealand (5 - 8 Aug, 2018).
i) N Othman, NA Samsuri, MKA Rahim, K Kamardin, "Transmission Characteristics of
Meandered Bowtie Antenna at 2.4 GHz in Proximity to Human Body", 2018 IEEE 7th Asia-
Pacific Conference on Antenna and Propagation, Auckland, New Zealand (5 - 8 Aug, 2018).
j) N Othman, NA Samsuri, MKA Rahim, NA Elias, "SAR in the presence of conductive medical
implant at 0.9, 1.8 and 2.4 GHz due to close proximity antenna", 10th European Conference
on Antenna and propagation (Eucap 2016), Davos, Switzerland, 2016 (SCOPUS)
k) MA Abdullah, MKA Rahim, NA Murad, NA Samsuri, "Transmission Enhancement between
dual band textile diamond dipole antennas with dual band textile AMC", 10th European
Conference on Antenna and propagation (Eucap 2016), Davos, Switzerland, 2016.
(SCOPUS)
l) NA Elias , NA Samsuri, MKA Rahim, N Othman , " Deviations in EM radiation absorption due
to mechanical deformation of dual-band dipole textile antenna ", 10th European Conference
on Antenna and propagation (Eucap 2016), Davos, Switzerland, 2016 (SCOPUS).
m) MKA Rahim, MR Hamid, NA Samsuri, NA Murad, MFM Yusoff, HA Majid, „Frequency
reconfigurable antenna for future wireless communication system‟ 2016 46th European
Microwave Conference (EuMC), , pp 965-970, London 2016
n) O.Ayop, M. K. A. Rahim, N.A. Murad and N.A Samsuri, „Dual resonance circular ring-shaped
metamaterial absorber with wide operating angle', International Symposium on Antennas and
Propagation (ISAP 2015),Hobart, Tasmania, 9-12 Nov 2015
o) ME Jalil,NA Samuri, M. K. A. Rahim, R Dewan, „Compact chipless RFID metamaterial based
structure using textile material', International Symposium on Antennas and Propagation (ISAP
2016),KaohsiungHobart, Tasmania, 9-12 Nov 2015
p) AA Al-Hadi, M. K. A. Rahim, NA samsuri, „Evaluation of two-to eight-element antenna array
in mobile terminal', International Symposium on Antennas and Propagation (ISAP
2016),KaohsiungHobart, Tasmania, 9-12 Nov 2015
q) O.Ayop, M. K. A. Rahim, N.A. Murad and N.A Samsuri, 'Dual band Polarization Insensitive
Metamaetrial Absorber in X-band', International Symposium on Antennas and Propagation
(ISAP 2014),Kaohsiung, Taiwan, 2-5 Dec 2014
r) M.N.Osman, M. K. A. Rahim, M.F.M.Yusof, M.R.Hamid and H.A.Majid, 'Polarization
Reconfigurable Patch Antenna through modification of feeding network', International
Symposium on Antennas and Propagation (ISAP 2014),Kaohsiung, Taiwan, 2-5 Dec 2014
s) N.J.Ramly, M. K. A. Rahim, M.E.Jalil, N.A Samsuri and R Dewan, 'Leaf shaped dual band
antenna for wearable application', International symposium on Antennas and Propagation
(ISAP 2014),Kaohsiung, Taiwan, 2-5 Dec 2014
t) B.D.Bala, M. K. A. Rahim, N.A. Murad N.A Samsuri and M. Khalily, 'Dual band dialectric
resonator based on metamaterial', International symposium on Antennas and Propagation
(ISAP 2014), Kaohsiung, Taiwan, 2-5 Dec 2014
u) R.Dewan, M. K. A. Rahim, M.R.Hamid, H.A.Majid, M.F.M.Yusof, 'Ultra wideband Antenna with
tunable Artificial Magnetic Conductor',International Symposium on Antennas and Propagation
(ISAP 2014),Kaohsiung, Taiwan, 2-5 Dec 2014
v) M.A.A. Majid, M. K. A. Rahim, N.A. Murad N.A Samsuri N A Elias and M.H. Mokhtar, Fully
textile slot linear array antenna with curvature and crumpling analysis', International
Symposium on Antennas and Propagation (ISAP 2014),Kaohsiung, Taiwan, 2-5 Dec 2014
w) Bashir D Bala, Mohamad Kamal B.A Rahim, Noor Asniza Murad, Noor Asmawati Samsuri, "A
Dual Band Metamaterial Antenna with Circular Polarization," 8th Europen Conference on
Antenna and propagation (Eucap 2014), Den Haag, 7 – 11 April 2014.
x) M. N. Osman, M. K. A. Rahim, M. F. M. Yusoff, M. R. Hamid, N. A. Murad, N. A. Samsuri, H.
A. Majid, "Polarization Reconfigurable Circular Patch Antenna with Fixed Operating
Frequency", 8th Europen Conference on Antenna and propagation (Eucap 2014), Den Haag,
7 – 11 April 2014.
y) H. A. Majid, M. K. A. Rahim, O. Ayop, M. R. Hamid, N. A. Murad, N. A. Samsuri and M. F. M.
Yusoff, "Frequency Reconfigurable Wideband Monopole Antenna Using EBG Structures", 8th
Europen Conference on Antenna and propagation (Eucap 2014), Den Haag, 7 – 11 April 2014.
z) M. H. Mokhtar, M. K. A. Rahim, N. A. Murad, N.A Samsuri, H. A. Majid and M. A. Majid, "A
Compact Dual-Band Microstrip Antenna Array with Artificial Magnetic Conductor",8th Europen
Conference on Antenna and propagation (Eucap 2014), Den Haag, 7 – 11 April 2014.
 aa) O. Ayop, M. K. A. Rahim, N. A. Murad, N. A. Samsuri, "Dual Band Polarization Insensitive and
Wide Angle Circular Ring Metamaterial Absorber", 8th Europen Conference on Antenna and
propagation (Eucap 2014), Den Haag, 7 – 11 April 2014.
bb) N. A. Elias, N. A. Samsuri, M. K. A. Rahim and N. Othman, "The Effects of Human Body and
Bending on Dipole Textile Antenna Performance and SAR", The Asia Pacific Microwave
Conference 2012 (APMC 2012), Kaohsiung, Taiwan, 4-7 Dec 2012.

BOOK CHAPTER
a) NA Elias, NA Samsuri, MKA Rahim, ' Analytical Study of Energy Absorption in Human Body
Dueto Bendable Behaviour of Textile Antenna', Theory and Applications of Applied
Electromagnetics, pp 329-337, 2015
b) MEB Jalil, MKA Rahim, NA Samsuri, R Dewan, 'Multi-resonator Using Complementary Split
Ring Resonator for Chip-Less RFID Application, Theory and Applications of Applied
Electromagnetics, pp 215-221, 2015
c) R Dewan, MKA Rahim, MR Hamid, NA Samsuri, MFM Yusoff, BD Bala, ' Dual Band Stacked
Artificial Magnetic Conductor with Dipole Antenna', Theory and Applications of Applied
Electromagnetics, pp 197-2015, 2015
d) Ayop, MKA Rahim, NA Murad, NA Samsuri, ' Double Layer Polarization Insensitive
Metamaterial Absorber with Dual Resonances', Theory and Applications of Applied
Electromagnetics, pp 231-238, 2015
e) KA Kamarudin, NA Samsuri, 'The Effect of Human Body and Metallic Items on Antenna
Radiation Performance at 2.4 GHz and 5.8 GHz', Antenna and Applied Electromagnetics, Vol.
2, 2013
f) N Othman, NA Samsuri, 'Investigation of the Interaction between the Human Head and
Antenna at 2.4 GHz and 5.8 GHz', Antenna and Applied Electromagnetics, Vol. 2, 2013 .
Lampiran 6.4 Biodata Peneliti Mitra Internasional

Nama :Professor Dr Mohamad Kamal A Rahim

Institusi : Universiti Teknologi Malaysia
Bidang :Antenna, RF , Microwave and Metamaterial

Daftar Publikasi:ISI Publikasi (5 Tahun)

a. AK Vallappil, MKA Rahim, BA Khawaja, MN Iqbal, ‘Compact Metamaterial Based Butler
Matrix With Improved Bandwidth for 5G Applications’, IEEE Access 8, 13573-13583,
2020 (ISI-Q1)
b. BAF Esmail, HA Majid, SH Dahlan, Z Zainal abidin, M Himdi, R Dewan, Mohamad KA
Rahim, Adel YI Ashyap, ‘Reconfigurable metamaterial structure for 5G beam tilting
antenna applications’, Waves in Random and Complex Media, 1-14, 2020 (ISI-Q1)
c. Bashar AF Esmail, HA Majid, ZZ Abidin, SH Dahlan, M Himdi, R Dewan, MKA Rahim, N
AL‐Fadhali, ‘Reconfigurable Radiation Pattern of Planar Antenna Using
Metamaterial for 5G Applications’, Journals Materials, Vol 13 (3), pp 1-15, 2020
(ISI-Q2)
d. Najib AL‐Fadhali, Huda A Majid, Rosli Omar, Samsul H Dahlan, Adel YI Ashyap,
Shaharil M Shah, Mohamad KA Rahim, Bashar AF Esmail, Mohamad K A Rahim and Muzammil
Jusoh. ‘Substrate integrated waveguide cavity backed frequency reconfigurable
antenna for cognitive radio applies to internet of things applications,
International Journal of RF and Microwave Computer Aided Engineering, Vol 30(1),
pp 1-6, Jan 2020, (ISI-Q3)
e. MW Sabri, NA Murad, MKA Rahim, ‘Highly directive 3D‐printed dual‐beam waveguide
slotted antennas for millimeter‐wave applications’ Microwave and Optical
Technology Letters 61 (6), 1566-1573, 2019 (ISI-Q4)
f. BA Esmail, HB Majid, ZBZ Abidin, SHB Dahlan, M Himdi, MR Kamarudin, MKA Rahim,
‘Dual mode modified double square ring resonator structure at 76 GHz’ Microwave
and Optical Technology Letters 61 (7), 1678-1682, 2019 (ISI-Q4)
g. Bashar AF Esmail, Huda A Majid, Shamsul H Dahlan, Zuhairiah Z Abidin, Mohamad K A
Rahim and Muzammil Jusoh. ‘Planar antenna beam deection using low‐loss
metamaterial for future 5G applications’, International Journal of RF and
Microwave Computer Aided Engineering, Vol 29(10), pp 1-6, 7 June 2019, (ISI-Q3)
h. BAF Esmail, HA Majid, ZZ Abidin, SH Dahlan, MKA Rahim, O Ayop, ‘New metamaterial
structure with reconfigurable refractive index at 5G candidate band’, Journal of
Optoelectronics and Advanced Materials 21 (1-2), pp 101-107, 2019 (ISI-Q4)
i. Hayat Ullah, Muhammad Amir, Ihsan Ul Haq, Shafqat Ullah Khan, M.K.A Rahim, Khan
Bahadar Khan, ‘Wavelet Based Desoising Using Logarithmic Shrinkage Function’,
 Wireless Personal Communication, Volume 98, Issue 1 pp 1473-1488, Jan 2018 (ISI-
Q4)
j. Hayat Ullah, Muhammad Amir, Ihsan Ul Haq, Shafqat Ullah Khan, M.K.A Rahim, Khan
Bahadar Khan, ‘Wavelet Based Desoising Using Logarithmic Shrinkage Function’,
Wireless Personal Communication, Volume 98, Issue 1 pp 1473-1488, Jan 2018 (ISI-
Q4)
k. Shafqat Ullah Khan, M.K.A.Rahim, M. Aminu Baba, N.A, Murad, ‘Correction of failure
in linear antenna arrays with greedy sparseness constrained optimization
technique’, PLOS one, Vol 12, Issue 12, Dec 2017 (ISI-Q1)
l. S.M Salleh, M Jusoh, A.H Ismail, M.R. Kamaruddin, P Nobles, M.K.A Rahim, T
Sabapathy, M.N. Osman, M.I Jais and S.P Jack, ‘Textile Antenna with Simultaneous
Frequency and Polarization Reconfiguration for WBAN’, IEEE Access Inpress 2017
(ISI-Q1)
m. Izni Husna Idris, Mohamad Rijal Hamid, Mohamad Kamal A Rahim, Kamailia Kamardin,
‘A multi to wideband frequency reconfigurable antenna’ International Journal of
RF and Microwave Computer-Aided Engineering, pp 1-9, Dec 2017 10.1002/mmce.21216
(ISI-Q3)
n. O Ayop, MKA Rahim, NA Murad, NA Samsuri, F Zubir, HA Majid, 'Dual-band metamaterial
perfect absorber with nearly polarization-independent' Applied Physics A, Vol 123
(1), 63, Jan 2017 (ISI- Q3)
o. ME Jalil, MKA Rahim, NA Samsuri, R Dewan, K Kamardin, 'Flexible ultra-wideband
antenna incorporated with metamaterial structures: multiple notches for chipless
RFID application' Applied Physic A, Vol 123 (1), 48, Jan 2017 (ISI - Q3)
p. MF Ismail, MKA Rahim, HA Majid, MR Hamid, MFM Yusoff, R Dewan, 'Pattern
reconfigurable antenna using electromagnetic band gap structure' Applied Physics
A, Vol 123 (1), 17, Jan 2017 (ISI - Q3)
q. R Dewan, MKA Rahim, M Himdi, MR Hamid, HA Majid, ME Jalil, 'Multiband frequency-
reconfigurable antenna using metamaterial structure of electromagnetic band gap'
Applied Physics A, Vol 123 (1), 16, Jan 2017 (ISI - Q3)
r. Dewan, R., Rahim, M. K. A., Hamid, M. R., Yusoff, M. F. M., Samsuri, N. A., Murad,
N. A. & Kamardin, K, ‘ Artificial Magnetic Conductor for various application: An
Overview’, International Journal of RF and Microwave Computer-Aided Engineering,
Vol 27, Issue 6, August 2017 (ISI - Q3)
s. Shafqat Ullah Khan, M. K. A. Rahim, N. A. Murad, F. Zubir, O. Ayop, M. F. M.
Yusoff, M. R. Hamid, and R. Dewan, ‘Detection of the Faulty Sensors on Basis of
the Pattern Using Symmetrical Structure of Linear Array Antenna‘, Applied
Electromagnetic Computational Society Jurnal (ACES), Vol 32 , No 4, pp 358-365,
2017 (ISI-Q3)
t. S.U.Khan, MKA Rahim, ‘Correction of failure in antenna array using matrix pencil
technique’, Chinese Physics B – June 2017 Volume 26, Issue 6 (ISI-Q2)
u. Shafqat Ullah Khan, M. K. A. Rahim, ‘Correction of Array Failure Using Gray Wolf
Optimizer Hybridized with an Interior Point Algorithm’,Frontiers of Information
Technology & Electronic Engineering, 2017 (ISI-Q4)
v. I.H.Idris, M.R.Hamid, K.Kamardin, M. K. A Rahim 'Wide to multiband reconfigurable
antenna' Microwave optical technology letter, Vol 58 Issue 9, pp 2079 - 2082, 2016
(ISI-Q4)
w. R. Dewan, M.K.A Rahim, M.R. Hamid, H.A.Majid, M.F.M.Yusof, M.E.Jalil,
'Reconfigurable antenna using capacitive loading Artificial Magnetic Conductor'
Microwave optical technology letter, Vol 58 Issue 10, pp 2422 - 2429, 2016 (ISI-
Q4)
x. M.N.Osman, M.K.A.Rahim, M.R.Hamid and M.F.M.Yusof, 'Compact Dual-Port Polarization
Reconfigurable Antenna with High Isolations for MIMO Application' Antenna
Wireless Propagation letter, Vol 15, pp 456 - 456 Feb 2016 (ISI- Q2)
y. M.I.A.Sukur, M. K. A Rahim, N.A. Murad, 'Bandwidth enhancement of rectangular
dielectric resonator antenna using circular slot coupled technique' Microwave
optical technology letter, Vol 58 Issue 3, pp 505 - 509, 2016 (ISI- Q4)
z. Kamilia Kamardin, Mohamad Kamal A Rahim, Peter S. Hall, Noor Asmawati Samsuri,
Tarik Abdul latef and Mohammad Habib Ullah , ‘Textile artificial magnetic
conductorjacket for transmission enhancement between antennas under bending and
wetness measurements’ Applied Physics A, April 2016 (ISI-Q2)