Electronic Applications III (ELA216A / ELT31AI) / Electronics III (ELA31BI)

Timed Assignment 2 (TA2)

Release Date: 01/06/2021

Submission Date: 03/06/2021

Duration: 3 days

Marks: 60

INSTRUCTIONS

Alphanumeric calculators are allowed.

Use the EXACT METHOD for ALL the QUESTIONS.

Answer all questions and enter your answers on ETHUTO on the spaces provided.

Please SAVE and SUBMIT ALL answers 10 minutes before the end of the Timed Assignment

session, as NO ANSWERS will be marked when submitted 2 minutes beyond the

session end.

Round all answers to two (2) decimal places with calculator in the engineering mode.

Please, take note of the format and / or notation in which the answers are required.

The CENTRAL UNIVERSITY OF TECHNOLOGY, FREE STATE assessment rules apply.

STATIONARY

o DOWNLOAD the assignment from Ethuto, work OFFFLNE and come UPLOAD all
your answers on ETHUTO – ALL this should be accomplished WITHIN THE
ALLOTTED TIME.

Declaration of Own Work

Page 1 of 6
By submitting my work on this platform, I declare that: 1) I have completed this

assignment / assessment in accordance with the CUT's Code of Academic Integrity;

2) All the work included in this assignment / assessment is my own work; and 3) I did

not consult any person or means other than that allowed by the assignment /

assessment instructions.

Page 2 of 6
Unit 1: [4 marks: Natural Science]

A sinusoidal waveform is displayed on an oscilloscope and has a peak-to-peak

A square wave of 10 V peak is connected to an analogue multimeter that is set to

[4]

Unit 2: [2 marks: Natural Science]

Given four machines producing 60 dB, 51dB, 50 dB, and 49 dB respectively, what is
the total sound pressure level? (dB):
2

[2]

Unit 3: [24 marks: Engineering Science]

Table 1: Oscillator circuit parameters and circuit components

C2 = 5100 pF; Amplifier gain = 11; Select R1/R2 = C2/C1, f = 20 kHz

From Table 1, determine R3 in terms of R4:

From Table 1, determine R1 in terms of R2:

From Table 1, determine C2 in terms of C1:

From Table 1, determine C1, (pF):

What is the E24 standard value of C1 as determined in the preceding question (pF):
2

From Table 1, determine R1, (kilo-ohms):

Page 3 of 6
2

What is the E24 standard value of R1 as determined in the preceding question (kilo-
ohms):
2

From Table 1, determine R2, (kilo-ohms):

What is the E24 standard value of R2 as determined in the preceding question (kilo-
ohms):
2

From Table 1, determine R4, (kilo-ohms):

From Table 1, determine R3, (kilo-ohms):

What is the E24 standard value of R3 as determined in the preceding question (kilo-
ohms):
2

[24]

Unit 4: [10 marks: Engineering Science]

Table 2: Band-pass circuit parameters and circuit components

R1 = 75 kΩ; C = 10 nF; R4 = 2 kΩ
Note: The circuit is to be designed for a narrow-band Av/f response.

From Table 2, determine R2 (kilo-ohms):

From Table 2, determine C1 (= C2) (uF):

From Table 2, determine the circuit Q factor (dimensionless):

From Table 2, determine the centre frequecny (Hz):

From Table 2, determine the circuit bandwidth (Hz):

[10]
Page 4 of 6
Unit 5: [20 marks: Engineering Science]

Table 3: Amplifier device parameters and circuit components

hie = 1.4 kΩ; hfe = 90; hoe = 10 x 10-7; Cc = 6 pF; Cp = 46 pF; Lp = 150
uH; Rw = 5 Ω; Ls = 80 uH; Rs = 5 Ω; RL = 7k5; k = 0.014 and fo = 1.8
MHz

From Table 3, determine the capacitance to resonate the secondary (pF):

From Table 3, determine the mutual inductance between the coils (uH):
2

From Table 3, determine the resistance reflected from the secondary into the primary
(ohms):
2

From Table 3, determine the total primary resistance (ohms):

From Table 3, determine the impedance of the parallel LC circuit at resonance (kilo-
ohms):
2

From Table 3, determine the transistor collector load resistance (kilo-ohms):

From Table 3, determine the voltage gain from the input to the primary winding
(dimensionless) (kilo):
2

From Table 3, determine the ratio of the secondary to primary voltage (dimensionless)
(milli):
2

From Table 3, determine the ratio of the output to secondary voltage (dimensionless)
(hecto):
2

From Table 3, determine the overall voltage gain from the input to the secondary
winding (dimensionless) (kilo):
2

[20]

[Total = 4 + 2 + 24 + 10 +20 = 60]

Page 5 of 6
END

Page 6 of 6