Riso RZ Series Error Codes By Ali Zghyebeh

Riso RZ Series Error Codes List

 Code: A01-201
 Description:Master-positioning sensor does not go ON even after
the write pulse motor is activated during the master-positioning,
master-cut, ormaster-loading operation.

 Code: A01-202
 Description:Master-positioning sensor does not go OFF even when
the write pulse motor is reversed during the master-positioning or at
start ofmaster-making operation.

 Code: A01-206

‫ﻣﺭ‬
 Description:Timeout error during master-making operation

 Code: A01-211




Code: A01-214 ‫ﻛﺯ‬
Description:Master-positioning sensor is ON during standby.

Description:Master-positioning sensor is ON at the start of master

making.
‫ﺧﺩ‬
 Code: A01-215
 Description:Faulty gate-array control for the write pulse motor
‫ﻣﺔ‬

(motor does not stop within set time)

 Code: A02-509
 Description:Master-loading sensor was OFF when the master was
‫ﺭﻳ‬

checked at a specified drum angle during the master-loading

oper201ation.
‫ﺯﻭ‬

 Code: A04-303
 Description:Master-disposal jam sensor was OFF at both 120 and
180 degrees drum angle.

 Code: A04-314
 Description:Master-disposal error (recovery error).

 Code: A05-304
 Description:Master-disposal jam sensor was ON at the completion
of the master-disposal operation.

‫مركز خدمة ريزو ـ حسان آغا‬

1
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: A05-312
 Description:The master-disposal jam sensor was ON at the start of
master-making operation.

 Code: A05-315
 Description:The master-disposal jam sensor was ON when the
master disposal box was set in the machine.

 Code: A06-403
 Description:Paper-feed-tray upper or lower safety switch is OFF.

 Code: A07-409
 Description:Paper-ejection sensor was OFF when the paper should
have arrived, and the paper sensor was ON when the machine

‫ﻣﺭ‬
stopped (Papermisfeed).

 Code: A07-412




Code: A07-413
‫ﻛﺯ‬
Description:Paper sensor was OFF three times in succession when
a paper misfeed was detected (paper misfeed).

Description:Paper sensor was ON when the paper should have left

‫ﺧﺩ‬
the paper sensor (long-length paper mode error).

 Code: A07-418
‫ﻣﺔ‬

 Description:The paper sensor was ON at the start of machine

operation when the START button was pressed.

 Code: A07-429
‫ﺭﻳ‬

 Description:Paper feed error (recovery error).

 Code: A07-432
‫ﺯﻭ‬

 Description:Paper sensor was ON when the machine went into

paper feed retry movement after a paper misfeed.

 Code: A08-410
 Description:Paper-ejection sensor was OFF when paper should
have arrived, and the paper sensor was OFF when the machine
stopped (paper jamon the print drum).

 Code: A08-421
 Description:Paper sensor was ON when the paper should have left
the paper sensor during feeding of long paper in long-length paper
mode (paperlonger than 555 mm).

‫مركز خدمة ريزو ـ حسان آغا‬

2
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: A08-430
 Description:Paper jam on print drum (recovery error).

 Code: A09-411
 Description:Paper-ejection sensor was ON when the paper should
have left the paper-ejection sensor.

 Code: A09-417
 Description:Paper-ejection sensor was ON at the start of machine
operation when the START button was pressed.

 Code: A09-431
 Description:Paper-ejection error (recovery error).

‫ﻣﺭ‬
 Code: A10-102
 Description:Original-registration-sensor remaining jam






Code: A10-103

‫ﻛﺯ‬
Description:Original-IN-sensor remaining jam

Code: A10-105
Description:Original-registration-sensor non-arrival jam
‫ﺧﺩ‬
 Code: A10-106
 Description:Original-IN-sensor non-arrival jam
‫ﻣﺔ‬

 Code: A10-107
 Description:Original-OUT-sensor non-arrival jam
‫ﺭﻳ‬

 Code: A10-109
 Description:An original feed error occurred, due to opening the AF.
‫ﺯﻭ‬

 Code: A10-162
 Description:No original in AF during AF master making.

 Code: A16-525
 Description:Waiting for the master to be removed.

 Code: A17-209
 Description:Cutter home-position switch is OFF at the start of
master-making or master-set operation.

 Code: A34-218
 Description:Request to resetting the master.

‫مركز خدمة ريزو ـ حسان آغا‬

3
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: B01-730
 Description:Keycard counter: No card

 Code: B22-721
 Description:With the “Tape separation” function set ON, no power is
supplied to the job separator when start key is pressed.

 Code: B22-727
 Description:After cluster-A signal turned ON, BUSY-signal stayed
"L" more than 7 seconds (power to job separator was turned OFF
while the tape isbeing ejected.

 Code: B23-722
 Description:With the “Tape separation” function set ON, no tape

‫ﻣﺭ‬
detected in the job separator when the start key is pressed.

 Code: B23-723




Code: B24-724
‫ﻛﺯ‬
Description:No tape remains in job separator upon completion of the
tape-ejection operation.

Description:Tape jam detected when the start key is pressed with

‫ﺧﺩ‬
the “Tape separation” function set to ON.

 Code: B24-725
‫ﻣﺔ‬

 Description:Job separator tape-jam detection signal is “H” within

1,200 milliseconds after the cluster-A signal turns ON (tape misfeed).

 Code: B24-726
‫ﺭﻳ‬

 Description:Job separator tape-jam detection signal is “L” when the

BUSY signal changes from “L” to “H” (or after 7 sec. at “L”) after the
cluster-Asignal goes ON (tape misfeed).
‫ﺯﻭ‬

 Code: B31-916
 Description:Network cable is not connected when the machine is
powered ON.

 Code: B32-917
 Description:Communication error on the network.

 Code: B32-920
 Description:Error detected by Network Interface Card (NIC) - NAK
(negative acknowledgement was received).

 Code: B33-931
 Description:DHCP server is not found with DHCP ON.

‫مركز خدمة ريزو ـ حسان آغا‬

4
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: B34-919
 Description:Error detected on the locally connected printer.

 Code: C01-512
 Description:The ink sensor did not go ON even when inking was
performed for the preset period.

 Code: C01-563
 Description:Ink remaining amount is zero.

 Code: C01-574
 Description:Inkless error was detected 5 times consecutively on one
same ink bottle.

‫ﻣﺭ‬
 Code: C02-200
 Description:The master end was detected twice in succession at 10-
milliseconds intervals during master transport.





Code: C02-240
‫ﻛﺯ‬
Description:Master remaining amount is zero

Code: C03-308
‫ﺧﺩ‬
 Description:Compression detection position was reached before the
master-compression-motor encoder-sensor count reached the
specified level,after the master compression motor turned ON in the
‫ﻣﺔ‬

compression direction.

 Code: C03-313
 Description:Master removal box full detected by the master removal
‫ﺭﻳ‬

count.

 Code: C04-402
‫ﺯﻭ‬

 Description:Paper detection sensor is OFF (no paper on the feed

tray).

 Code: D01-526
 Description:Print drum is not set in the machine (drum connection
signal, drum safety switch, and drum-lock sensor is OFF.

 Code: D01-527
 Description:Print drum connection signal is OFF when the print
drum was inserted in the machine.

 Code: D01-528
 Description:Print drum safety switch is OFF when the print drum
was inserted in the machine.

‫مركز خدمة ريزو ـ حسان آغا‬

5
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: D01-529
 Description:Print drum lock sensor is OFF when the print drum was
inserted in the machine (time-out: 5 seconds).

 Code: D01-530
 Description:Print drum connection signal does not go OFF within 5
seconds after the print drum safety switch went OFF when the print
drum waspulled out.

 Code: D02-532
 Description:Incorrect print drum is used.

 Code: D03-533
 Description:Ink cartridge set sensor is OFF.

‫ﻣﺭ‬
 Code: D04-534
 Description:Incorrect ink cartridge is used.





Code: D04-560
‫ﻛﺯ‬
Description:Ink TAG is not detected on ink bottle.

Code: D04-561
‫ﺧﺩ‬
 Description:Ink cartridge communication error (communication with
the ink cartridge was interfered by noise).
‫ﻣﺔ‬

 Code: D04-562
 Description:Wrong ink cartridge information.

 Code: D04-564
‫ﺭﻳ‬

 Description:Detected a mismatch in ink cartridge information

 Code: D05-210
‫ﺯﻭ‬

 Description:Master detection sensor is OFF (not detecting master).

 Code: D07-310
 Description:Disposal-box safety switch is OFF.

 Code: D08-224
 Description:Master making unit is not set (both the safety switch and
lock sensor are OFF).

 Code: D08-226
 Description:Master making unit safety switch is still OFF when the
master making unit is set in position.

‫مركز خدمة ريزو ـ حسان آغا‬

6
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: D08-227
 Description:Master making unit lock sensor is still OFF when the
master making unit is set in position (timeout: 5 seconds).

 Code: D08-228
 Description:Master making unit lock sensor is still ON even after the
master making unit safety switch went OFF, when the master making
unit waspulled out of the machine.

 Code: D09-212
 Description:Master-making-unit set sensor is OFF (sensor light path
is free).

 Code: D11-535

‫ﻣﺭ‬
 Description:Front cover set switch is OFF.

 Code: D13-9




Code: D17-236
Description:Incorrect master roll.
‫ﻛﺯ‬
Description:The rear cover is opened (serviceman safety switch is
OFF).
‫ﺧﺩ‬
 Code: D17-237
 Description:Master roll undetected.
‫ﻣﺔ‬

 Code: D17-238
 Description:Master roll communication error.
‫ﺭﻳ‬

 Code: D17-239
 Description:Wrong master roll detected.
‫ﺯﻭ‬

 Code: D17-241
 Description:Detected a mismatch in master roll information.

 Code: D18-522
 Description:Print drum ready for release (solenoid is ON).

 Code: D19-223
 Description:Master making unit ready for release (solenoid is ON).

 Code: D22-540
 Description:Error in access to the Drum PCB (unable to read from
or write on the Drum PCB).

‫مركز خدمة ريزو ـ حسان آغا‬

7
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: D22-542
 Description:Abnormal data on Drum PCB.

 Code: E01-10
 Description:Battery voltage was less than 2.5 V when the power
was switched ON (weak battery: time to replace battery).

 Code: E02-11
 Description:Master counter reached the value set for the
maintenance call (value set by test mode). [The message appears
when either the power isturned ON, the unit is reset, or when the
machine operation ended.]

 Code: E02-12

‫ﻣﺭ‬
 Description:Copy counter reached the value set for the maintenance
call (value by set test mode). [The message appears when either the
power isturned ON, the unit is reset, or when the machine operation



ended.]

Code: E02-22 ‫ﻛﺯ‬

Description:Maintenance counter inside the print drum reached the
value set for the maintenance call (value set by test mode). [The
‫ﺧﺩ‬
messageappears when either the power is turned ON, the unit is
reset, or when the machine operation ended.]
‫ﻣﺔ‬

 Code: F01-15
 Description:There is no master on the print drum at the start of
printing.
‫ﺭﻳ‬

 Code: F02-18
 Description:Paper size does not match with the image size on the
print drum at the start of printing.
‫ﺯﻭ‬

 Code: F03-16
 Description:Multi-up was selected using custom size paper.

 Code: F05-19
 Description:In master making, the print quantity selected is less than
the minimum print quantity.

 Code: F10-21
 Description:Paper size does not match with the size of image on the
print drum when test print is selected and activated.

‫مركز خدمة ريزو ـ حسان آغا‬

8
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: F21-32
 Description:Next original is not in placed on AF for multi-up
operation.

 Code: F22-33
 Description:Next original is not placed on flatbed for multi-up
operation.

 Code: F37-50
 Description:Original was set on the AF with book mode selected,
when master making is activated.

 Code: F50-910
 Description:Auto-printer-selection is disabled due to error on linked

‫ﻣﺭ‬
printer.

 Code: F54-923




Code: F55-924
‫ﻛﺯ‬
Description:Auto-printer-selection is disabled due to no paper in the
linked printer.

Description:Auto-printer-selection is disabled while receiving print

‫ﺧﺩ‬
data from PC.

 Code: F58-927
‫ﻣﺔ‬

 Description:Cannot print from linked printer (Initializing NET-C).

 Code: H1-566
 Description:Requesting ink color information input (Ink-TAG
‫ﺭﻳ‬

related).

 Code: H2-567
‫ﺯﻭ‬

 Description:Requesting print density information input (Ink-TAG

related).

 Code: H3-568
 Description:Requesting test printing print density information input
(Ink-TAG related).

 Code: H4-242
 Description:Requesting master-making density information input
(Master-TAG related).

 Code: H5-243
 Description:Requesting Print density information input (Master-TAG
related).

‫مركز خدمة ريزو ـ حسان آغا‬

9
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: H6-244
 Description:Requesting test printing print density information input
(Master-TAG related).

 Code: P01-520
 Description:Main encoder sensor does not go ON/OFF within 10
milliseconds after the main motor activates.

 Code: P01-521
 Description:B-positioning sensor status does not change even after
3,033 pulses after the main motor activates.

 Code: P01-524
 Description:Clamp unit is not at the home position while the print

‫ﻣﺭ‬
drum is in operation (except during master disposal).

 Code: P01-537




Code: P01-538 ‫ﻛﺯ‬
Description:Print drum failed to stop at position B. (over-run)

Description:Print drum is not locked during operation. (Print-drum

lock position sensor: OFF)
‫ﺧﺩ‬
 Code: P02-400
 Description:Both the upper and lower limit sensors were ON at the
‫ﻣﺔ‬

same time.

 Code: P02-401
 Description:Overload current was detected in the elevator motor.
‫ﺭﻳ‬

 Code: P02-404
 Description:The lower-limit sensor does not go OFF within 2
‫ﺯﻭ‬

seconds after the elevator motor operates in the raising direction

from the lower-limitposition.

 Code: P02-405
 Description:The upper-limit sensor does not go ON within 12
seconds after the elevator motor operates in the raising direction.

 Code: P02-406
 Description:The upper-limit sensor does not go OFF within 2
seconds after the elevator motor operates in the lower direction from
the upper-limitposition.

‫مركز خدمة ريزو ـ حسان آغا‬

10
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P02-407
 Description:The lower-limit sensor does not go ON within 12
seconds after the elevator motor operates in the lowering direction.

 Code: P02-408
 Description:The upper-limit sensor is OFF continuously for over 2
seconds during operation of the elevator servo action to raise the
feed tray.

 Code: P03-500
 Description:Clamp sensor A is OFF after the completion of the
clamp unit initialization or home positioning movement.

 Code: P03-501

‫ﻣﺭ‬
 Description:Clamp sensor B does not change within 1 second from
the time the clamp motor operates in the correct direction.





Code: P03-502

‫ﻛﺯ‬
Description:Clamp sensor B does not change within 1 second from
the time the clamp motor operates in the reverse direction.

Code: P03-503
‫ﺧﺩ‬
 Description:Clamp sensor A does not go ON within 3 seconds when
the clamp unit makes initialization movement.
‫ﻣﺔ‬

 Code: P03-504
 Description:At the start of Clamp plate open/close action, the the
detection sequence of clamp-sensors A & B is abnormal.
‫ﺭﻳ‬

 Code: P03-505
 Description:At the start of print drum Positon-A compensation
movement, the detection sequence of clamp-sensors A & B is
‫ﺯﻭ‬

abnormal.

 Code: P03-506
 Description:At the start of Clamp unit Home-positioning movement,
the detection sequence of clamp-sensors A & B is abnormal.

 Code: P03-507
 Description:Clamp sensor A is ON after the clamp release action is
completed.

 Code: P03-508
 Description:Clamp sensor A is ON after the A-position
compensating movement is completed.

‫مركز خدمة ريزو ـ حسان آغا‬

11
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P03-545
 Description:Clamp unit is not in the home position while the print
drum is in movement (cause due to the clamp motor).

 Code: P04-513
 Description:The overflow sensor was ON for a set number of times
in succession during the 10-millisecond-interval overflow-sensor
check.

 Code: P05-603
 Description:The vertical-centering sensor does not switch ON even
when the vertical-positioning pulse motor activated in the image-
down direction for5 seconds during vertical home positioning
movement.

‫ﻣﺭ‬
 Code: P05-604
 Description:The vertical-centering sensor does not switch OFF even



Code: P05-605
‫ﻛﺯ‬
when the vertical-positioning pulse motor activated in the image-up
direction for 5seconds during vertical home positioning movement.

Description:Even though the vertical positioning motor stopped

‫ﺧﺩ‬
according to the vertical centering sensor detection, the stopping
position does notcorrespond with the programmed position. (GA
control error).
‫ﻣﺔ‬

 Code: P05-612
 Description:The one-step-positioning key was pressed with vertical-
print-position information undefined.
‫ﺭﻳ‬

 Code: P08-951
 Description:Print job executed was not in correct RisoRinc format.
‫ﺯﻭ‬

 Code: P11-600
 Description:Print pressure HP sensor does not switch ON within 3.9
seconds after the print pressure pulse motor activated towards higher
pressureduring home positioning operation.

 Code: P11-601
 Description:Print pressure HP sensor does not switch OFF within
4.6 seconds after the print pressure pulse motor activated towards
lower pressureduring home positioning operation.

‫مركز خدمة ريزو ـ حسان آغا‬

12
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P11-602
 Description:Even though the print pressure control pulse motor
stopped according to the print pressure HP sensor detection, the
stopping positiondoes not correspond with the programmed position.
(GA control error).

 Code: P12-300
 Description:Overload current was detected in the master removal
motor.

 Code: P12-301
 Description:Master compression motor lock when moving
compression plate up.

‫ﻣﺭ‬
 Code: P12-305
 Description:Master compression sensor does not go ON within 6.5
seconds after the master compression motor operates in the return



direction.

Code: P12-306 ‫ﻛﺯ‬

Description:Master compression sensor does not go OFF within 2
seconds after the master compression motor operates in the
‫ﺧﺩ‬
compress direction.

 Code: P12-307
‫ﻣﺔ‬

 Description:Master compression plate maximum position is not

detected within 6.5 seconds after the master compression motor
operates in thecompress direction.
‫ﺭﻳ‬

 Code: P12-309
 Description:Master-compression-motor encoder sensor count did
not change as the master compression motor activated in the
‫ﺯﻭ‬

compress directionand moved out from the home position.

 Code: P12-316
 Description:Master-compression-motor encoder sensor count did
not change within 10 milliseconds after the master compression
motor activated.

 Code: P13-203
 Description:Cutter HP switch does not go OFF within 100
milliseconds after the cutter motor is activated.

‫مركز خدمة ريزو ـ حسان آغا‬

13
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P13-204
 Description:Cutter HP switch does not go ON within 300
milliseconds after the cutter motor is activated.

 Code: P13-205
 Description:Master-positioning sensor is ON when the print drum
rotates through the preset angle following master cutting.

 Code: P13-221
 Description:Both the cutter HP switch and cutter stop position switch
are ON at the same time.

 Code: P13-222
 Description:Cutter HP switch does not go ON within 450

‫ﻣﺭ‬
milliseconds after the cutter home positioning operation started.

 Code: P13-231




Code: P13-232
‫ﻛﺯ‬
Description:Cutter HP switch does not go OFF within 500
milliseconds after the cutter moved out from the home position.

Description:Cutter stop position switch does not go ON within 2

‫ﺧﺩ‬
seconds after the cutting operation started.

 Code: P13-233
‫ﻣﺔ‬

 Description:Cutter stop position switch does not go OFF within 500

milliseconds after the cutter activates to move from the stop position
to the homeposition.
‫ﺭﻳ‬

 Code: P13-234
 Description:Cutter HP switch does not go ON within 2 seconds after
the cutter home positioning operation started.
‫ﺯﻭ‬

 Code: P14-114
 Description:Incorrect main-unit data.

 Code: P14-115
 Description:The scanner operation is not completed within the set
time.

 Code: P14-116
 Description:Timeout error for black shading compensation. (RZ3
series only)

‫مركز خدمة ريزو ـ حسان آغا‬

14
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P14-117
 Description:Timeout error for white shading compensation. (RZ3
series only)

 Code: P14-123
 Description:Offset adjustment not completed within set time. (RZ3
series only)

 Code: P14-124
 Description:Gain adjustment not completed within set time. (RZ3
series only)

 Code: P14-125
 Description:Offset adjustment not completed.

‫ﻣﺭ‬
 Code: P14-126
 Description:Gain adjustment not completed.



Code: P14-135
‫ﻛﺯ‬
Description:Malfunction detected during offset adjustment. (RZ3
series only)
‫ﺧﺩ‬
 Code: P14-136
 Description:Malfunction detected during offset adjustment. (RZ3
series only)
‫ﻣﺔ‬

 Code: P14-137
 Description:Malfunction detected during black shading
compensation. (RZ3 series only)
‫ﺭﻳ‬

 Code: P14-138
 Description:Malfunction detected during white shading
‫ﺯﻭ‬

compensation. (RZ3 series only)

 Code: P14-170
 Description:Even though the read pulse motor stopped according to
the sensor detection, the stopping position does not correspond with
theprogrammed position. (GA control error).

 Code: P15-110
 Description:ABC (auto-base-control) timeout. The original does not
move from the ABC scanning position on the AF unit.

 Code: P15-111
 Description:Operation command was made to the AF unit without
24 volts supplied to the AF unit.

‫مركز خدمة ريزو ـ حسان آغا‬

15
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P15-130
 Description:Timeout error in receiving reply from the AF unit after
command signal was sent from the Riso printer to the AF unit.

 Code: P15-131
 Description:Riso printer received an undefined command from the
AF unit.

 Code: P15-132
 Description:Riso printer detected communication sequence error
from the AF unit.

 Code: P15-133
 Description:Communication error with AF unit (ACK or NAK error).

‫ﻣﺭ‬
 Code: P15-134
 Description:Riso printer could not send command to the AF unit



within the set time.

Code: P15-160 ‫ﻛﺯ‬

Description:AF unit detection signal went OFF while the AF unit is in
operation.
‫ﺧﺩ‬
 Code: P15-4
 Description:Communication error with AF-CPU.
‫ﻣﺔ‬

 Code: P17-20
 Description:Solenoid counter is not connected.
‫ﺭﻳ‬

 Code: P18-531
 Description:Print drum lock sensor is still ON even after 100
milliseconds after the print drum lock solenoid is activated.
‫ﺯﻭ‬

 Code: P19-207
 Description:TPH pressure sensor does not go OFF within 2 seconds
after the thermal-pressure motor activates in the decompressing
direction, orduring home positioning operation.

 Code: P19-208
 Description:TPH pressure sensor does not go ON within 2 seconds
after the thermal-pressure motor activates in the decompressing
direction.

‫مركز خدمة ريزو ـ حسان آغا‬

16
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P19-216
 Description:TPH pressure sensor does not go OFF within 500
millisecond after the thermal-pressure motor activates in the
compressing direction.

 Code: P19-217
 Description:TPH pressure sensor does not go ON within 2 seconds
after the thermal-pressure motor activates in the compressing
direction.

 Code: P20-415
 Description:Paper-ejection-wing home sensor does not go OFF
within 7,000 milliseconds after the paper ejection wing motor
activates in thecounterclockwise direction from the home position.

‫ﻣﺭ‬
 Code: P20-416
 Description:Overload current was detected in the paper-ejection



motor.

Code: P20-437 ‫ﻛﺯ‬

Description:Paper-ejection encoder sensor status does not change
within 10 milliseconds after the paper-ejection motor is activated.
‫ﺧﺩ‬
 Code: P24-539
 Description:Inking-motor encoder sensor status does not change
‫ﻣﺔ‬

within 20 milliseconds after the inking-motor is activated.

 Code: P25-26
 Description:Battery voltage was below 2.3 volts (too low) when the
‫ﺭﻳ‬

power is turned ON.

 Code: P92-570
‫ﺯﻭ‬

 Description:EEPROM on the print drum PCB was being accessed

while the print drum was in releasing action from the machine.

 Code: P93-932
 Description:No reply from the NET-C network interface card while
accessing to the network interface card.

 Code: P93-933
 Description:No response from NET-C for 90 seconds during NET-C
initialization.

 Code: P94-225

‫مركز خدمة ريزو ـ حسان آغا‬

17
 Riso RZ Series Error Codes By Ali Zghyebeh
 Description:TPH code does not match with the machine code when
the power is turned ON with the master-making unit in operating
position or whenthe master-making unit is inserted in operating
position while the power is ON.

 Code: P95-59
 Description:Machine serial-number information sent from SH-PCB
does not match with the machine serial number information in the
MCTL PCB.

 Code: P96-171
 Description:TPH resistance value not input.

 Code: P96-172

‫ﻣﺭ‬
 Description:Scanner adjustment not completed.

 Code: P96-433




Code: P96-569
‫ﻛﺯ‬
Description:Paper size width potentiometer test-mode setting is not
completed.

Description:Either the print drum color information or ink category

‫ﺧﺩ‬
information is still not input.

 Code: P96-613
‫ﻣﺔ‬

 Description:Print pressure data missing.

 Code: P98-119
 Description:Image processing PCB trouble.
‫ﺭﻳ‬

 Code: P98-120
 Description:Scanner communication problem. (RZ3 series only)
‫ﺯﻭ‬

 Code: P98-129
 Description:Faulty Scanner GA PCB. (RZ3 series only)

 Code: P98-2
 Description:No reply from Mini-Rosa PCB when the machine power
is turned ON even though the Rosa connection signal is ON.

 Code: P98-245
 Description:Master transfer time-out error during master making
(Write pulse motor error).

‫مركز خدمة ريزو ـ حسان آغا‬

18
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P98-246
 Description:Master transfer time-out error during master making
(Load pulse motor error).

 Code: P98-38
 Description:Machine data on EEPROM does not match with that on
the SH-PCB

 Code: P98-39
 Description:Improper EEPROM on the SH-PCB.

 Code: P98-46
 Description:The DIMM capacity does not match.

‫ﻣﺭ‬
 Code: P98-5
 Description:Hardware error.






Code: P98-51

‫ﻛﺯ‬
Description:Touch-panel communication error

Code: P98-53
Description:Failure in calling out the saved Memory settings
‫ﺧﺩ‬
(program, mode, user paper information).

 Code: P98-54
‫ﻣﺔ‬

 Description:Failure in saving the Memory settings (program, mode,

user paper information).

 Code: P98-55
‫ﺭﻳ‬

 Description:Machine type code from SH-PCB does not match with

the machine information on the H8-PCB.
‫ﺯﻭ‬

 Code: P98-6
 Description:FRAM checksum error.

 Code: P98-614
 Description:Vertical print position data missing.

 Code: P98-63
 Description:The test-mode memory data stored was outside the
adjustment range.

 Code: P98-64
 Description:An undefined command was sent in communication
between SH-PCB and MCTL PCB.

‫مركز خدمة ريزو ـ حسان آغا‬

19
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P98-65
 Description:Communication error 01 between SH-PCB and MCTL
PCB (MCTL PCB side).

 Code: P98-67
 Description:Communication error 03 between SH-PCB and MCTL
PCB (MCTL PCB side).

 Code: P98-68
 Description:Communication error 04 between SH-PCB and MCTL
PCB (MCTL PCB side).

 Code: P98-69
 Description:Communication error 05 between SH-PCB and MCTL

‫ﻣﺭ‬
PCB (MCTL PCB side).

 Code: P98-7




Code: P98-70 ‫ﻛﺯ‬
Description:Mini Rosa PCB not connected.

Description:Communication error 06 between SH-PCB and MCTL

PCB (MCTL PCB side).
‫ﺧﺩ‬
 Code: P98-71
 Description:Communication error 07 between SH-PCB and MCTL
‫ﻣﺔ‬

PCB (MCTL PCB side).

 Code: P98-72
 Description:Communication error 08 between SH-PCB and MCTL
‫ﺭﻳ‬

PCB (MCTL PCB side).

 Code: P98-73
‫ﺯﻭ‬

 Description:Communication error 09 between SH-PCB and MCTL

PCB (MCTL PCB side).

 Code: P98-74
 Description:Communication error 10 between SH-PCB and MCTL
PCB (SH-PCB side)

 Code: P98-75
 Description:Communication error 11 between SH-PCB and MCTL
PCB (SH-PCB side)

 Code: P98-76
 Description:Communication error 12 between SH-PCB and MCTL
PCB (SH-PCB side)

‫مركز خدمة ريزو ـ حسان آغا‬

20
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P98-77
 Description:Communication error 13 between SH-PCB and MCTL
PCB (SH-PCB side)

 Code: P98-78
 Description:Communication error 14 between SH-PCB and MCTL
PCB (SH-PCB side)

 Code: P98-79
 Description:Communication error 15 between SH-PCB and MCTL
PCB (SH-PCB side)

 Code: P98-80
 Description:Communication error 16 between SH-PCB and MCTL

‫ﻣﺭ‬
PCB (SH-PCB side)

 Code: P98-81




Code: P98-82
‫ﻛﺯ‬
Description:Communication error 17 between SH-PCB and MCTL
PCB (SH-PCB side)

Description:Communication error 18 between SH-PCB and MCTL

‫ﺧﺩ‬
PCB (SH-PCB side)

 Code: P98-83
‫ﻣﺔ‬

 Description:Communication error 19 between SH-PCB and MCTL

PCB (SH-PCB side)

 Code: P98-84
‫ﺭﻳ‬

 Description:Communication error 20 between SH-PCB and MCTL

PCB (SH-PCB side)
‫ﺯﻭ‬

 Code: P98-934
 Description:Main read/write communication error (detected by
read/write side).

 Code: P98-935
 Description:Main read/write communication error (detected by
machine side).

 Code: P98-937
 Description:Serial number data missing.

 Code: P98-938
 Description:FRAM version-down.

‫مركز خدمة ريزو ـ حسان آغا‬

21
 Riso RZ Series Error Codes By Ali Zghyebeh
 Code: P98-947
 Description:24V-A does not go ON (a possible burnt 24-volt group-A
fuse).

 Code: P98-948
 Description:24V-B does not go ON (a possible burnt 24-volt group-B
fuse).

 Code: P98-949
 Description:24V-A does not go OFF.

 Code: P98-950
 Description:24V-B does not fo OFF.

‫ﻣﺭ‬
 Code: P98-952
 Description:Checksum error on the ROSA flash-memory.






Code: P98-953

‫ﻛﺯ‬
Description:Unsuccessful writing on the ROSA flash-memory.

Code: P98-98
Description:Machine serial number information on the SH-PCB
‫ﺧﺩ‬
EEPROM does not match with that in the FRAM.

 Code: P99-936
‫ﻣﺔ‬

 Description:Software error
‫ﺭﻳ‬
‫ﺯﻭ‬

‫مركز خدمة ريزو ـ حسان آغا‬

22