Sintec Optronics Technology Pte Ltd

Sintec Optronics Technology Pte Ltd

10 Bukit Batok Cres #07-02 The Spire Singapore 658079
Tel: +65 63167112 Fax: +65 63167113

Laser Reflective Mirrors, Output Couplers & Beam Splitters

Name Description Remark

φ10x3mm, R=50mm Plano-concave, HR1064nm, HT532nm
φ10x3mm, R=65mm Plano-concave, HR1064nm, HT532nm
532nm output coupler φ10x3mm, R=100mm Plano-concave, HR1064nm, HT532nm
S1: HR1064nm, HT532nm
φ20x5mm, flat-flat mirror
S2: HT532nm
φ40x3mm, R=10%
φ40x3mm, R=13%
φ40x3mm, R=15%
φ40x3mm, R=20%
φ40x3mm, R=30%
φ40x3mm, R=33%
φ40x3mm, R=50%
532nm beam splitter & φ40x3mm, R=100%
reflective mirror φ50x3mm, R=10%
φ50x3mm, R=13%
φ50x3mm, R=15%
φ50x3mm, R=20%
φ50x3mm, R=30%
φ50x3mm, R=33%
φ50x3mm, R=50%
φ50x3mm, R=100%
φ40x3mm, R=10%
φ40x3mm, R=13%
φ40x3mm, R=15%
φ40x3mm, R=20%
φ40x3mm, R=30%
φ40x3mm, R=33%
φ40x3mm, R=50%
1064nm beam splitter & φ40x3mm, R=100%
reflective mirror φ50x3mm, R=10%
φ50x3mm, R=13%
φ50x3mm, R=15%
φ50x3mm, R=20%
φ50x3mm, R=30%
φ50x3mm, R=33%
φ50x3mm, R=50%
φ50x3mm, R=100%

说明：
1. Regarding φ50x3mm, 50 means diameter, 3 means thickness, unit is mm.
2. Regarding R=10%, R means reflectivity and unit is %.
3. Regarding T=10%, T means transmittance and unit is %.
4. Regarding R=50mm, R means radius of curvature and unit is mm.
5. HR1064nm means high reflectivity at 1064nm (>98%).
6. HT532nm means high transmittance at 532nm (>98%).
7. Plano-concave means that one surface is flat and another surface is concave.

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 1
 Sintec Optronics Technology Pte Ltd

Reflective Mirror and Output Coupler at 1064nm

Material BK7
Diameter tolerance -0.1mm
Thickness tolerance 0.1mm
Aperture >90%
Flatness λ/4-λ
Dig/scratch 60-40

Part Number Description:

LM-1064-D-T-R-A-%-yy
LM: laser mirror. R>99.5%.
1064: laser wavelength in nm.
D: mirror diameter in mm. If rectangular, it is AxB.
T: thickness in mm.
R: radius of curvature in mm. It is flat mirror if ther is no this
number. It is plano-convex if it is minus.
A: incidence angle, degree. It is normal incidence if there is no this
number.
%: tranmittance of output coupler.
yy: other marks.

Part number Name Wavelength Dia. ThicknessRemark

LM-1064-D20-T5 Mirror 1064nm 20mm 5mm 0o, flat
LM-1064-D20-T3-A45 Mirror 1064nm 20mm 3mm 45o, flat
LM-1064-D20-T5-A45 Mirror 1064nm 20mm 5mm 45o, flat
LM-1064-D25.4-T3-A45 Mirror 1064nm 25.4mm 3mm 45o, flat
LM-1064-D30-T5-A45 Mirror 1064nm 30mm 5mm 45o, flat
LM-1064-D40-T5-A45 Mirror 1064nm 40mm 5mm 45o, flat
LM-1064-D50-T5-A45 Mirror 1064nm 50mm 5mm 45o, flat
0o, plano-concave,
LM-1064-D20-T5-R500 Mirror 1064nm 20mm 5mm
R500mm
LM-1064-D20-T5-R1500 Mirror 1064nm 20mm 5mm 0o, plano-concave, R1.5m
LM-1064-D20-T5-R2000 Mirror 1064nm 20mm 5mm 0o, plano-concave, R2m
LM-1064-D25.4-T3-A45 Mirror 1064nm 25.4mm 3mm 45o, flat
LM-1064-54x38-T5-A45-XD Mirror 1064nm 54x38 5mm 45o, octagon
LM-1064-D20-T5-10% Coupler 1064nm 20mm 5mm 0o, flat, T=10%
0o, plano-concave,
LM-1064-D20-T5-R250-10% Coupler 1064nm 20mm 5mm
R25cm, T=10%
LM-1064-D20-T5-15% Coupler 1064nm 20mm 5mm 0o, flat, T=15%
LM-1064-D20-T5-20% Coupler 1064nm 20mm 5mm 0o, flat, T=20%
0o, plano-concave, R2M,
LM-1064-D20-T5-R2000-20% Coupler 1064nm 20mm 5mm
T=20%
LM-1064-D20-T5-40% Coupler 1064nm 20mm 5mm 0o, flat, T=40%
LM-1064-D20-T5-50% Coupler 1064nm 20mm 5mm 0o, flat, T=50%
LM-1064-D20-T5-70% Coupler 1064nm 20mm 5mm 0o, flat, T=70%
LM-1064-D20-T5-80% Coupler 1064nm 20mm 5mm 0o, flat, T=80%
There are too many items and models and welcome to call us or send us an email if you have any
further enquiry or question!

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 2
 Sintec Optronics Technology Pte Ltd

Resonator Mirrors of Diode End-pumped Lasers

Part Number Name Dia. thk Remark

LM-DPSS-D20-T5-HT808-HR1064 Rear mirror 20mm 5mm 0o, flat, HT@808nm, HR@1064nm
LM-DPSS-D10-T3-HT808-HR1064 Rear mirror 10mm 3mm 0o, flat, HT@808nm, HR@1064nm
Remark: The output couplers at 1064nm can be used as the output coupler in the diode end-pumped
lasers.

Resonator Mirrors of SHG Lasers

Part Number Name Dia. thk Remark

LM-SHG-D20-T5-HR1064-HR532 Rear mirror 20mm 5mm 0o, flat, HR@1064nm & 532nm
LM- SHG-D20-T5-HR1064-HT532 Output coupler 20mm 5mm 0o, flat, HR@1064nm & HT@532nm

Protective Window
Part Number Name Dia. thk Remark
LW-532-D70-T4.1-BX-1 Protective window 70mm 4.1mm 0o, PL/PL AR/AR@532nm
LW-1060/1080-D50-T2-H-BX-1 Protective window 50mm 2mm 0o, PL/PL AR/AR@1060-1080nm
LW-1060/1080-D55-T2-H-BX-1 Protective window 50mm 2mm 0o, PL/PL AR/AR@1060-1080nm

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 3
 Sintec Optronics Technology Pte Ltd

Si Mirrors
Silicon mirrors in a huge range of sizes are available, with a selection of different coatings to suite you
application.
z Advanced manufacturing methods
z Latest ultra-low absorption coatings
z Highest quality substrates

Dia ET A T R S2 ROC
Part No. M Coating
mm mm deg % % m
LM-SI-5.9SIS4-03 Si 15 4 45 3 99.93 3 SuperMax
LM-SI-7.5SID2-00 Si 19 2 45 0 99 flat SiDual
LM-SI-7.5SIS3-00 Si 19 3 45 0 99.93 flat SuperMax
LM-SI-7.5SIS3-05 Si 19 3 45 0 99.93 5 SuperMax
LM-SI-7.5SIS3-07 Si 19 3 45 0 99.93 7 SuperMax
LM-SI-7.5SIS4-05 Si 19 4 45 0 99.93 5 SuperMax
LM-SI-7.5SIS5-075 Si 19 5 45 0 99.93 0.75 SuperMax
LM-SI-10SIF3-00 Si 25.4 3 45 0 99 flat PFM
LM-SI-10SIF5-00 Si 25.4 5 45 0 99 flat PFM
LM-SI-10SIS3-00 Si 25.4 3 45 0 99.93 flat SuperMax
LM-SI-10SIS3-05 Si 25.4 3 45 0 99.93 5 SuperMax
LM-SI-10SIS3-10 Si 25.4 3 45 0 99.93 10 SuperMax
LM-SI-10SIS4-00 Si 25.4 4 45 0 99.93 flat SuperMax
LM-SI-10SIS5-00 Si 25.4 5 45 0 99.93 flat SuperMax
LM-SI-11SIS3-00 Si 28 3 45 0 99.93 flat SuperMax
LM-SI-11SIS6-00 Si 28 6 45 0 99.93 flat SuperMax
LM-SI-15SIS6.3-07 Si 38.05 6.3 45 0 99.93 7 SuperMax
LM-SI-15SIS6.3-7M Si 38.05 6.3 45 0 99.93 7.5 SuperMax
LM-SI-15SIS6-00 Si 38.05 6 45 0 99.93 flat SuperMax
LM-SI-15SIS9.5-00 Si 38.05 9.5 45 0 99.93 flat SuperMax
LM-SI-15SIS9.7-00 Si 38.05 9.7 45 0 99.93 flat SuperMax
LM-SI-15SID-00 Si 38.05 4 45 0 99 flat SiDual
LM-SI-15SIF4-00 Si 38.05 4 45 0 99 flat PFM
LM-SI-15SIS4-10CC Si 38.05 4 45 0 99.93 10 SuperMax
LM-SI-15SIS5-00 Si 38.05 5 45 0 99.93 flat SuperMax
LM-SI-15SIS6.3-00 Si 38.1 6.3 45 0 99.93 flat SuperMax
LM-SI-15SIS6.6-00 Si 38.1 6.6 45 0 99.93 flat SuperMax
LM-SI-16.1SIS5-00 Si 41 5 45 0 99.93 flat SuperMax
LM-SI-17.5SIS9.5-00 Si 44.45 9.5 45 0 99.93 flat SuperMax
LM-SI-17.5SIS9-00 Si 44.5 9 45 0 99.93 flat SuperMax
LM-SI-17.5SIS4-00 Si 44.5 4 45 0 99.93 flat SuperMax
LM-SI-19.7SIS10-00 Si 50 10 45 0 98.6 flat SuperMax
LM-SI-19.7SIS5-00 Si 50 5 45 0 98.6 flat SuperMax
LM-SI-20SIF10-00 Si 50.8 10 45 0 99 flat PFM
LM-SI-20SIS10-00 Si 50.8 10.2 45 0 99.93 flat SuperMax
LM-SI-20SIS10-00MA Si 50.8 10 45 0 99.93 flat SuperMax
LM-SI-20SIS5-00 Si 50.8 5.1 45 0 99.93 flat SuperMax
LM-SI-20SIS9.5-00 Si 50.8 9.5 45 0 99.93 flat SuperMax
LM-SI-26.8SIS20-00M Si 68 20 45 0 99.93 flat SuperMax
LM-SI-30SIS6.35-00 Si 76.2 6.35 45 0 99.93 flat SuperMax
LM-SI-30SMA12.7-00 Cu 76.2 12.7 45 0 98.6 flat SuperMax
Remark: M: material; A(deg): angle of incidence; ET: edge thickness; T(%): transmission; R (%):
reflectance; ROC: radius of curvature.

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 4
 Sintec Optronics Technology Pte Ltd

Turning Mirrors, Silicon

These turning mirrors are used in CO2 laser beam delivery systems. Silicon is the most commonly used
mirror substrate due to its good "figure of merit" properties. We offer them with a variety of metal and
dielectric coatings.

z TMS-EM Turning Mirrors Enhanced Metal for CO2 10.6 µm Reflectance coating
z 45° Angle Of Incidence
z Coated: Reflectance > 99.6% average @ 10.6 µm
z Absorption: < .30% @ 10.6 µm

Model Number Diameter Thickness

LM-SI-TMS-0512-EM 0.500" 0.120"
LM-SI-TMS-0712-EM 0.750" 0.120"
LM-SI-TMS-0912-EM 0.875" 0.120"
LM-SI-TMS-1012-EM 1.000" 0.120"
LM-SI-TMS-1112-EM 1.100" 0.120"
LM-SI-TMS-1512-EM 1.500" 0.120"
LM-SI-TMS-1516-EM 1.500" 0.160"
LM-SI-TMS-1816-EM 1.750" 0.160"
LM-SI-TMS-2020-EM 2.000" 0.200"
LM-SI-TMS-2525-EM 2.500" 0.250"
LM-SI-TMS-3025-EM 3.000" 0.250"
LM-SI-TMS-4035-EM 4.000" 0.350"

Turning Mirrors, Silicon Dual-Band Reflector for CO2 + Red Laser Diode Reflectance

z TMS-DBMR Turning Mirrors Silicon with Dual Band Max Reflectance coating
z Coated: Reflectance > 99.7% average @ 10.6 µm
z Reflectance: > 85% average for .633 µm and 650 nm
z 45° Angle Of Incidence
z Absorption: < 0.30% @ 10.6 µm

Model Number Diameter Thickness

LM-SI-TMS-0512-DBMR 0.500" 0.120"
LM-SI-TMS-0712-DBMR 0.750" 0.120"
LM-SI-TMS-0912-DBMR 0.875" 0.120"
LM-SI-TMS-1012-DBMR 1.000" 0.120"
LM-SI-TMS-1112-DBMR 1.100" 0.120"
LM-SI-TMS-1512-DBMR 1.500" 0.120"
LM-SI-TMS-1516-DBMR 1.500" 0.160"
LM-SI-TMS-1816-DBMR 1.750" 0.160"
LM-SI-TMS-2020-DBMR 2.000" 0.200"
LM-SI-TMS-2525-DBMR 2.500" 0.250"
LM-SI-TMS-3025-DBMR 3.000" 0.250"
LM-SI-TMS-4035-DBMR 4.000" 0.350"

Phase Retardation Reflectors : Silicon for CO2 Lasers and 10.6µm

These mirrors create a 90° Phase Shift with the aid of specially constructed thin film coating layers
applied to the surface, when hit with a linear polarized beam at 45° to the plane of incidence.
Commonly called Phase Shifters, Polarizers, or Circular Polarizing Mirrors, they transform the incoming
beam into a circular polarized state. They typically are only used external to the laser cavity as a beam
delivery mirror. These operate only with a true 10.6µm laser wavelength and will not work at other
wavelengths such as 9.2 or 9.6µm without special modifications to the thin film coating design. We offer
non-standard wavelength Phase Retardation Reflectors at these other wavelengths as custom parts.

z Phase Shift: 90°±3.0° between p and s polarization for 10.6µm operation only @ 45° Angle Of
Incidence
z Reflectance: > 99.0% average @ 10.6µm
z Absorption: < 0.40% @ 10.6µm

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 5
 Sintec Optronics Technology Pte Ltd

z Coating optimized to create 90° phase shift from a linear polarized beam. Used in beam delivery
systems where cutting circles in materials is required.

Part Number Diameter Thickness

LM-SI-PRRS-0712-90 0.750" 0.120"
LM-SI-PRRS-1012-90 1.000" 0.120"
LM-SI-PRRS-1112-90 1.100" 0.120"
LM-SI-PRRS-1516-90 1.500" 0.160"
LM-SI-PPRS-1816-90 1.75 0.160"
LM-SI-PRRS-2020-90 2.000" 0.200"
LM-SI-PRRMS-5010-90 50 mm 10 mm
LM-SI-PRRS-2038-90 2.000" 0.375"
LM-SI-PRRS-2525-90 2.500" 0.250"
LM-SI-PRRS-3025-90 3.000" 0.250"
LM-SI-PRRS-3050-90 3.000" 0.500"
LM-SI-PRRMS-7515-90 75 mm 15 mm

Zero Phase Reflectors: Silicon for CO2 Lasers and 10.6µm

z Phase Shift: <2.0° between p and s polarization for 10.6µm operation only @ 45° Angle Of
Incidence
z Reflectance: > 99.6% average @ 10.6µm
z Absorption: < 0.40% @ 10.6µm
z Coating optimized to maintain low phase shift in beam delivery systems where a 90° phase
retarder exists to maintain the circular polarization.

Model Number Diameter Thickness

LM-SI-ZPRS-0712-0 0.750" 0.120"
LM-SI-ZPRS-1012-0 1.000" 0.120"
LM-SI-ZPRS-1112-0 1.100" 0.120"
LM-SI-ZPRS-1516-0 1.500" 0.160"
LM-SI-ZPRS-1816-0 1.750" 0.160""
LM-SI-ZPRS-2020-0 2.000" 0.200"
LM-SI-ZPR-50-5-10-0 50 mm 10 mm
LM-SI-ZPRS-2038-0 2.000" 0.375"
LM-SI-ZPRS-2525-0 2.500" 0.250"
LM-SI-ZPRS-3025-0 3.000" 0.250"
LM-SI-ZPRS-3050-0 3.000" 0.500"
LM-SI-ZPR-75-5-15-0 75 mm 15 mm
LM-SI-ZPRS-4035-0 4.000" 0.350"

Total Reflectors: Silicon Concave for CO2 Lasers and 10.6µm

z Turning Mirrors Silicon with Dual Band Max Reflectance coating

z Coated: Reflectance > 99.6% average @ 10.6 µm
z Operation at normal incidence (0°)
z Reflectance: > 85% average for 633 nm and 650 nm
z Absorption: < 0.30% @ 10.6 µm
z Clear Aperture: 90% of diameter

Model Number Diameter Thickness Concave Radius (meters)

LM-SI-TRCCS-0512-2-EM 0.500" 0.120" 2 meter
LM-SI-TRCCS-0512-3-EM 0.500" 0.120" 3 meter
LM-SI-TRCCS-0512-5-EM 0.500" 0.120" 5 meter
LM-SI-TRCCS-0512-7.5-EM 0.500" 0.120" 7.5 meter
LM-SI-TRCCS-0512-10-EM 0.500" 0.120" 10 meter
LM-SI-TRCCS-0712-2-EM 0.750" 0.120" 2 meter
LM-SI-TRCCS-0712-3-EM 0.750" 0.120" 3 meter
LM-SI-TRCCS-0712-5-EM 0.750" 0.120" 5 meter
LM-SI-TRCCS-0712-6-EM 0.750" 0.120" 6 meter
LM-SI-TRCCS-0712-7.5-EM 0.750" 0.120" 7.5 meter
LM-SI-TRCCS-0712-10-EM 0.750" 0.120" 10 meter
http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 6
 Sintec Optronics Technology Pte Ltd

LM-SI-TRCCS-1012-2-EM 1.00" 0.120" 2 meter

LM-SI-TRCCS-1012-3-EM 1.00" 0.120" 3 meter
LM-SI-TRCCS-1012-5-EM 1.00" 0.120" 5 meter
LM-SI-TRCCS-1012-7.5-EM 1.00" 0.120" 7.5 meter
LM-SI-TRCCS-1012-10-EM 1.00" 0.120" 10 meter
LM-SI-TRCCS-1012-20-EM 1.00" 0.120" 20 meter
LM-SI-TRCCS-1112-2-EM 1.10" 0.120" 2 meter
LM-SI-TRCCS-1112-3-EM 1.10" 0.120" 3 meter
LM-SI-TRCCS-1112-5-EM 1.10" 0.120" 5 meter
LM-SI-TRCCS-1112-7.5-EM 1.10" 0.120" 7.5 meter
LM-SI-TRCCS-1112-10-EM 1.10" 0.120" 10 meter
LM-SI-TRCCS-1112-20-EM 1.10" 0.120" 20 meter
LM-SI-TRCCS-1516-2-EM 1.50" 0.160" 2 meter
LM-SI-TRCCS-1516-3-EM 1.50" 0.160" 3 meter
LM-SI-TRCCS-1516-5-EM 1.50" 0.160" 5 meter
LM-SI-TRCCS-1516-7.5-EM 1.50" 0.160" 7.5 meter
LM-SI-TRCCS-1516-10-EM 1.50" 0.160" 10 meter
LM-SI-TRCCS-1516-20-EM 1.50" 0.160" 20 meter
LM-SI-TRCCS-2020-2-EM 2.00" 0.200" 2 meter
LM-SI-TRCCS-2020-3-EM 2.00" 0.200" 3 meter
LM-SI-TRCCS-2020-5-EM 2.00" 0.200" 5 meter
LM-SI-TRCCS-2020-7.5-EM 2.00" 0.200" 7.5 meter
LM-SI-TRCCS-2020-10-EM 2.00" 0.200" 10 meter
LM-SI-TRCCS-2020-20-EM 2.00" 0.200" 20 meter

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 7
 Sintec Optronics Technology Pte Ltd

Cu Mirrors
Copper mirrors in a huge range of sizes are available, with a selection of different coatings to suite you
application.
z Advanced manufacturing methods
z Latest ultra-low absorption coatings
z Highest quality substrates

S2
Dia ET A T R
Part No. M ROC Coating
mm mm deg % %
m
LM-CU-11SMA6-00 Cu 28 6 45 0 99.93 flat SuperMax
LM-CU-15NCA8-00 Cu 38 8 45 0 99.93 flat NiCu
LM-CU-15NCW15-00 Cu 38 15 45 0 98.6 flat NiCu
LM-CU-D38-T10-A45 Cu 38 10 45 0 98.6 flat NiCu
LM-CU-15NCA10-00 Cu 38 6 45 0 98.6 flat NiCu
LM-CU-15NCA6-00 Cu 38 6 45 0 98.6 flat SuperMax
LM-CU-15SMA6-00 Cu 38 6 45 0 99.93 flat SuperMax
LM-CU-15SMA6-15 Cu 38.05 6 45 0 99.93 15 SuperMax
LM-CU-19.7NCA10-00 Cu 50 10 45 0 98.6 flat NiCu
LM-CU-19.7NCW25-00 Cu 50 25 45 0 98.6 flat NiCu
LM-CU-19.7SMA10-1000CX Cu 50 6 45 0 98.6 flat SuperMax
LM-CU-19.7SMA5-00 Cu 50 5 45 0 98.6 flat SuperMax
LM-CU-19.7SMA9-00 Cu 50 9 45 0 98.6 flat SuperMax
LM-CU-20NCA5-00 Cu 50.8 5 45 0 98.6 flat NiCu
LM-CU-20SMA5-00 Cu 50.8 5 45 0 98.6 flat SuperMax
LM-CU-23.6NCA10-00 Cu 60 10 45 0 98.6 flat NiCu
LM-CU-23.6SMA6-00 Cu 60 6 45 0 98.6 flat SuperMax
LM-CU-29.5NCA15-00 Cu 75 15 45 0 98.6 flat NiCu
LM-CU-29.5NCW25-00 Cu 75 25 45 0 98.6 flat NiCu
LM-CU-29.5SMA17-00 Cu 75 17 45 0 98.6 flat SuperMax
Remark: M: material; A(deg): angle of incidence; ET: edge thickness; T(%): transmission; R (%):
reflectance; ROC: radius of curvature.

Gold-coated Reflectors: Glass Substrate

Model Description Wavelength Dia Thk

LM-10.6-D20-T3 CO2 laser mirror, glass substrate 10.6um 20mm 3mm Gold coating, flat
LM-10.6-D25-T3 CO2 laser mirror, glass substrate 10.6um 25mm 3mm Gold coating, flat
Other dimension mirrors available upon request.

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 8
 Sintec Optronics Technology Pte Ltd

Mo Mirrors
Molybdenum mirrors in a huge range of sizes are available, with a selection of different coatings to suite
you application.
z Advanced manufacturing methods
z Latest ultra-low absorption coatings
z Highest quality substrates

S2
Dia ET A T R
Part No. M ROC Coating
mm mm deg % %
m
LM-MO-5.9MO2-00 Mo 15 2 0 0 98.5 flat Uncoated
LM-MO-15MO6-00 Mo 38 6 45 0 98.5 flat Uncoated
LM-MO-17.5MO8-00 Mo 44.5 8 45 0 98.5 flat Uncoated
LM-MO-19.7MO2-00 Mo 50 2 45 0 98.5 flat Uncoated
LM-MO-19.7MO3-00 Mo 50 3 45 0 98.5 flat Uncoated
LM-MO-19.7MO5-14 Mo 50 5 45 0 98.5 flat Uncoated
LM-MO-19.7MO6-00 Mo 50 6 45 0 98.5 flat Uncoated
LM-MO-20MO5-00 Mo 50.8 5.1 45 0 98.5 flat Uncoated
LM-MO-23.6MO10-00 Mo 60 10 45 0 98.5 flat Uncoated
LM-MO-29.5MO15-00 Mo 75 15 45 0 98.5 flat Uncoated
Remark: M: material; A(deg): angle of incidence; ET: edge thickness; T(%): transmission; R (%):
reflectance; ROC: radius of curvature.

Metal Mirrors, Molybdenum for CO2 Lasers and 10.6µm

z Uncoated
z Phase Shift: <2.0° between P and S polarization
z for 10.6µm operation only @ 45° Angle Of Incidence
z Reflectance: > 98.0% average @ 10.6µm

Model Number Diameter Thickness

LM-MO-MM-1012-UC 1.000" 0.120"
LM-MO-MM-1516-UC 1.500" 0.160"
LM-MO-MM-1525-UC 1.500" 0.250"
LM-MO-MM-2020-UC 2.000" 0.200"
LM-MO-MM-2038-UC 2.000" 0.380"
LM-MO-MM-3025-UC 3.000" 0.250"
LM-MO-MM-3050-UC 3.000" 0.500"

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 9
 Sintec Optronics Technology Pte Ltd

CO2 Laser 10.6um Flat Partial Reflectors (Output Couplers)

ZnSe partial reflectors can be fabricated in any diameter from 4.0mm up to 250mm, and in thicknesses
from 1.0mm up to 50mm. They differ from beam splitters in that the coatings are designed for normal
incidence.

z Many types available

z OEM equivalents for your laser cavity in stock
z Coatings from our Coating Services

Dia ET A T R
Part No. Material Coating
mm mm deg % %
LM-10.6-10ZPF3-17-N ZnSe 25.4 3 0 83 17 AR/17%
LM-10.6-10ZPF3-40-N ZnSe 25.4 3 0 60 40 AR/40%
LM-10.6-10ZPF3-50-N ZnSe 25.4 3 0 50 50 AR/50%
LM-10.6-10ZPF3-60-N ZnSe 25.4 3 0 40 60 AR/60%
LM-10.6-10ZPF3-65-N ZnSe 25.4 3 0 35 65 AR/65%
LM-10.6-10ZPF3-70-N ZnSe 25.4 3 0 30 70 AR/70%
LM-10.6-10ZPF3-75-N ZnSe 25.4 3 0 25 75 AR/75%
LM-10.6-10ZPF3-80-N ZnSe 25.4 3 0 20 80 AR/80%
LM-10.6-10ZPF3-85-N ZnSe 25.4 3 0 15 85 AR/85%
LM-10.6-10ZPF3-90-N ZnSe 25.4 3 0 10 90 AR/90%
LM-10.6-10ZPF3-95-N ZnSe 25.4 3 0 5 95 AR/95%
LM-10.6-10ZPF3-99-N ZnSe 25.4 3 0 1 99 AR/99%
LM-10.6-10ZPF3-99-R ZnSe 25.4 3 45 1 99 AR/99%-45R
LM-10.6-10ZPF4-85-N ZnSe 25.4 4 0 15 85 AR/85%
LM-10.6-10ZPF6-50-N ZnSe 25.4 6 0 50 50 AR/50%
LM-10.6-10ZPF6-60-N ZnSe 25.4 6 0 40 60 AR/60%
LM-10.6-10ZPF6-65-N ZnSe 25.4 6 0 35 65 AR/65%
LM-10.6-11GPF458679 GaAs 28 3 0 35 65 AR/65%
LM-10.6-11ZPF3-27-N ZnSe 28 3.1 0 73 27 AR/27%
LM-10.6-11ZPF3-50-N ZnSe 28 3 0 50 50 AR/50%
LM-10.6-11ZPF3-60-N ZnSe 28 3 0 40 60 AR/60%
LM-10.6-D28-11ZPF3-65-N ZnSe 28 3.1 0 35 65 AR/65%
LM-10.6-11ZPF3-85-N ZnSe 28 3.1 0 15 85 AR/85%
LM-10.6-11ZPF6-60-N ZnSe 28 6 0 40 60 AR/60%
LM-10.6-12.6ZPF5-17-N ZnSe 32 5 0 83 17 AR/17%
LM-10.6-15ZPF3-17-N ZnSe 38.05 3 0 83 17 AR/17%
LM-10.6-15ZPF3-1-N ZnSe 38.05 3 0 99 1 AR/1%
LM-10.6-15ZPF3-25-N ZnSe 38.05 3 0 75 25 AR/25%
LM-10.6-15ZPF3-33-N ZnSe 38.05 3 0 66.7 33.3 AR/33.3%
LM-10.6-15ZPF3-45-R ZnSe 38.05 3 45 55 45 AR/45%-45R
LM-10.6-15ZPF3-50-N ZnSe 38.05 3 0 50 50 AR/50%
LM-10.6-15ZPF3-57-N ZnSe 38.05 3 0 43 57 AR/57%
LM-10.6-15ZPF3-60-N ZnSe 38.05 3 0 40 60 AR/60%
LM-10.6-15ZPF3-65-N ZnSe 38.05 3 0 35 65 AR/65%
LM-10.6-15ZPF3-70-N ZnSe 38.05 3 0 30 70 AR/70%
LM-10.6-15ZPF3-75-N ZnSe 38.05 3 0 25 75 AR/75%
LM-10.6-15ZPF3-80-N ZnSe 38.05 3 0 20 80 AR/80%
LM-10.6-15ZPF3-85-N ZnSe 38.05 3 0 15 85 AR/85%
LM-10.6-15ZPF3-90-N ZnSe 38.05 6 0 10 90 AR/90%
LM-10.6-15ZPF4-25-N ZnSe 38.05 4 0 75 25 AR/25%
LM-10.6-15ZPF4-60-N ZnSe 38.05 4 0 40 60 AR/60%
LM-10.6-15ZPF6-99-N ZnSe 38.05 6 0 1 99 AR/99%
LM-10.6-15.7ZPF4-50-N ZnSe 40 4 0 50 50 AR/50%
LM-10.6-17.5ZPF4-17-N ZnSe 44.45 4 0 83 17 AR/17%
LM-10.6-19.7ZPF4-50-N ZnSe 50 4 0 50 50 AR/50%
LM-10.6-20ZPF5-50-S-9.4 ZnSe 50.8 5 45 50 50 AR/50%-45S
LM-10.6-20ZPF5-99-S-9.4 ZnSe 50.8 5 45 1 99 AR/99%-
Remark: M: material; A(deg): angle of incidence; ET: edge thickness; T(%): transmission; R (%):
reflectance; ROC: radius of curvature.

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 10
 Sintec Optronics Technology Pte Ltd

OCZ Series Flat Output Couplers

Specifications:
Material: Zinc Selenide (ZnSe) Laser Grade
Diameter Tolerances: +0.000”, -0.005” for parts up to 2.000”Ø
+0.000”, -0.010” for parts from 2.50” to 6.000”Ø
Thickness: ±.010”
Parallelism: < 3 minutes
Surface Quality: < 40/20 scratch – dig Laser Finish

Spectral Performance:
Side 1
Partial Reflectance Values as indicated
Tolerances on Reflectance
50-70% ±3.0%
75-85% ±2.0%
90-95% ±1.5%

Side 2
Standard high-efficiency low loss anti-reflectance thin film coating applied to this side only
Reflectance per surface @ 10.6µm for normal incidence <0.20%
Transmission: > 99.0%

Model Number Diameter Thickness % Reflectance

LM-10.6-OCZ-0512-50 0.500" 0.120" 50%
LM-10.6-OCZ-0512-70 0.500" 0.120" 70%
LM-10.6-OCZ-0512-75 0.500" 0.120" 75%
LM-10.6-OCZ-0512-80 0.500" 0.120" 80%
LM-10.6-OCZ-0512-85 0.500" 0.120" 85%
LM-10.6-OCZ-0512-90 0.500" 0.120" 90%
LM-10.6-OCZ-0512-95 0.500" 0.120" 95%
LM-10.6-OCZ-0712-50 0.750" 0.120" 50%
LM-10.6-OCZ-0712-70 0.750" 0.120" 70%
LM-10.6-OCZ-0712-75 0.750" 0.120" 75%
LM-10.6-OCZ-0712-80 0.750" 0.120" 80%
LM-10.6-OCZ-0712-85 0.750" 0.120" 85%
LM-10.6-OCZ-0712-90 0.750" 0.120" 90%
LM-10.6-OCZ-0712-95 0.750" 0.120" 85%
LM-10.6-OCZ-1012-50 1.000" 0.120" 50%
LM-10.6-OCZ-1012-70 1.000" 0.120" 70%
LM-10.6-OCZ-1012-75 1.000" 0.120" 75%
LM-10.6-OCZ-1012-80 1.000" 0.120" 80%
LM-10.6-OCZ-1012-85 1.000" 0.120" 85%
LM-10.6-OCZ-1012-90 1.000" 0.120" 90%
LM-10.6-OCZ-1012-95 1.000" 0.120" 95%
LM-10.6-OCZ-1512-50 1.500" 0.120" 50%
LM-10.6-OCZ-1512-70 1.500" 0.120" 70%
LM-10.6-OCZ-1512-75 1.500" 0.120" 75%
LM-10.6-OCZ-1512-80 1.500" 0.120" 80%
LM-10.6-OCZ-1512-85 1.500" 0.120" 85%
LM-10.6-OCZ-1512-90 1.500" 0.120" 90%
LM-10.6-OCZ-1512-95 1.500" 0.120" 95%
LM-10.6-OCZ-2020-50 2.000" 0.200" 50%
LM-10.6-OCZ-2020-70 2.000" 0.200" 70%
LM-10.6-OCZ-2020-75 2.000" 0.200" 75%
LM-10.6-OCZ-2020-80 2.000" 0.200" 80%
LM-10.6-OCZ-2020-85 2.000" 0.200" 85%
LM-10.6-OCZ-2020-90 2.000" 0.200" 90%
LM-10.6-OCZ-2020-95 2.000" 0.200" 95%

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 11
 Sintec Optronics Technology Pte Ltd

CO2 Laser 10.6um Curved Partial Reflectors (Output couplers)

ZnSe partial reflectors can be fabricated in any diameter from 4.0mm up to 250mm, and in thicknesses
from 1.0mm up to 50mm.

z Advanced in-house design

z Huge range of
z High quality laser grade material

S1 S2
A
Part No. M Dia ET T R ROC ROC Coating
deg
m m
LM-10.6-5.9ZPC0010 ZnSe 15 3 0 15 85 flat 10 AR/85%
LM-10.6-6.4ZPC0010 ZnSe 16.2 2.7 0 83 17 flat 3 AR/17%
LM-10.6-10GER15-99 Ge 25.4 6 0 0.4 99.6 flat 15 AR/99.6%
LM-10.6-10GER20-99 Ge 25.4 3 0 0.5 99.5 flat 20 AR/99.5%
LM-10.6-10ZPC0010 ZnSe 25.4 3 0 60 40 7.5 15 AR/40%
LM-10.6-10ZPC0015 ZnSe 25.4 3 0 50 50 flat 10 AR/50%
LM-10.6-10ZPC0020 ZnSe 25.4 3 0 50 50 7.5 10 AR/50%
LM-10.6-10ZPC0022 ZnSe 25.4 6 0 50 50 7.5 10 AR/50%
LM-10.6-10ZPC0030 ZnSe 25.4 3 0 50 50 7.5 15 AR/50%
LM-10.6-10ZPC0040 ZnSe 25.4 6 0 50 50 7.5 15 AR/50%
LM-10.6-10ZPC0045 ZnSe 25.4 6 0 40 60 flat 20 AR/60%
LM-10.6-10ZPC0050 ZnSe 25.4 6 0 35 65 30 30 AR/65%
LM-10.6-10ZPC0060 ZnSe 25.4 6 0 35 65 flat 15 AR/65%
LM-10.6-10ZPC0062 ZnSe 25.4 3 0 0.5 99.5 flat 10 AR/99.5%
LM-10.6-10ZPC0063 ZnSe 25.4 3 0 0.5 99.5 flat 15 AR/99.5%
LM-10.6-10ZPC0064 ZnSe 25.4 3 0 0.5 99.5 flat 20 AR/99.5%
LM-10.6-10ZPC0066 ZnSe 25.4 4.7 0 1 99 flat 3 AR/99%
LM-10.6-10ZPC0068 ZnSe 25.4 4 0 40 60 20 20 AR/60%
LM-10.6-10ZPC0070 ZnSe 25.4 6 0 0.4 99.6 flat 10 AR/99.6%
LM-10.6-10ZPC0080 ZnSe 25.4 6 0 0.4 99.6 flat 15 AR/99.6%
LM-10.6-10ZPC0085 ZnSe 25.4 6 0 0.4 99.6 flat 20 AR/99.6%
LM-10.6-10ZPC0090 ZnSe 25.4 6 0 0.4 99.6 flat 30 AR/99.6%
LM-10.6-11GER10-99.5 Ge 28 6 0 0.5 99.5 N/A N/A AR/99.5%
LM-10.6-11GER30-99.5 Ge 28 5.6 0 0.5 99.5 N/A N/A AR/99.5%
LM-10.6-11MNFO010 ZnSe 28 4 0 50 50 5 10 AR/50%
LM-10.6-11MNFO020 ZnSe 28 4 0 50 50 10 20 AR/50%
LM-10.6-11MNFO030 ZnSe 28 4 0 50 50 15 20 AR/50%
LM-10.611MNFO040 ZnSe 28 4 0 25 75 15 20 AR/75%
LM-10.6-11MANRO0010 ZnSe 28 4 0 0.8 99.2 flat 10 AR/99.2%
LM-10.6-11MANRO0020 ZnSe 28 4 0 0.8 99.2 flat 20 AR/99.2%
LM-10.6-11NFO010 ZnSe 28 4 0 50 50 5 10 AR/50%
LM-10.6-11NFO020 ZnSe 28 4 0 50 50 10 20 AR/50%
LM-10.6-11NFO030 ZnSe 28 4 0 50 50 15 20 AR/50%
LM-10.6-11NFO040 ZnSe 28 4 0 25 75 15 20 AR/75%
LM-10.6-11ZPC0010 ZnSe 28 6 0 50 50 7.5 10 AR/50%
LM-10.6-11ZPC0016 ZnSe 28 6 0 83 17 AR/17%
LM-10.6-11ZPC0020 ZnSe 28 6 0 40 60 7.5 15 AR/60%
LM-10.6-11ZPC0022 ZnSe 28 6 0 40 60 7.5 20 AR/60%
LM-10.6-11ZPC0030 ZnSe 28 4 0 35 65 flat 30 AR/65%
LM-10.6-11ZPC0033 ZnSe 28 3 0 1 99 flat 20 AR/99%
LM-10.6-11ZPC0040 ZnSe 28 4 0 35 65 flat 60 AR/65%
LM-10.6-11ZPC0041 ZnSe 28 4 0 60 40 AR/40%
LM-10.6-11ZPC0050 ZnSe 28 6 0 1 99 flat 20 AR/99%
LM-10.6-11ZPC0059 ZnSe 28 6 0 50 50 AR/50%
LM-10.6-12.6ZPC0010 ZnSe 32 5 0 0.4 99.6 flat 20 AR/99.6%
LM-10.6-15GER35-99.5 Ge 38.05 4 0 0.5 99.5 flat 35 AR/99.5%
LM-10.6-15ZPC0016 ZnSe 38.05 6.3 0 0.4 99.6 flat 20 AR/99.6%

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 12
 Sintec Optronics Technology Pte Ltd

LM-10.6-15ZPC0020 ZnSe 38.05 6 0 0.4 99.6 flat 20 AR/99.6%

LM-10.6-15ZPC0060 ZnSe 38.05 8 0 40 60 35 15 AR/60%
LM-10.6-20ZPC0011 ZnSe 50.8 5 0 15 85 AR/85%
Remark: M: material; A(deg): angle of incidence; ET: edge thickness; T(%): transmission; R (%):
reflectance; ROC: radius of curvature.

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 13
 Sintec Optronics Technology Pte Ltd

Nd:YAG Laser Focusing Lenses

1. Single-element Focusing Lens

For a single-element focusing lens with Plano-

convex shape, the effective focal length (EFL,
f) is

f =R
n −1

Front focal length (FFL) is equil to EFL. Back

focal length (BFL) is

⎡ t (n − 1) ⎤
BFL = f • ⎢1 − c
⎣ nR ⎥⎦

Where R is the curvature of radius, n is refractive index of the llens material, tc is the central thickness
of the lens.

Description of Part Number: FL-XXXX-F-D-T-EN-MN-YY

FL: single-element focusing lens
XXXX: laser wavelength, 1064nm.
F: focal length, mm
D: lens diameter, mm
T: lens edge thickness, mm
EN: Dimension unit is in inch (If there is no EN, it means
metric unit in mm).
MN: lens shape, MN means menicus, no MN means
plano-convex,
YY: others such as CC, UO, JS etc.
Coating: di-electric coating at 1064nm.

Wavelength Focal length Dia. Thickness Remark

Part number
nm mm mm mm
FL-1064-F14-D20-T2.3 1064 14 20 2.3
FL-1064-F24-D24-T2.1 1064 24 24 2.1
FL-1064-F25-D19-T1.5 1064 25 19 1.5
FL-1064-F30-D19-T1.5 1064 30 19 1.5
FL-1064-F30-D20-T2.3 1064 30 20 2.3
FL-1064-F35-D22-T2.3 1064 35 22 2.3
FL-1064-F37-D27-T2.5 1064 37 27 2.5
FL-1064-F54-D22-T2.7 1064 54 22 2.7
FL-1064-F54-D28-T3.0 1064 54 28 3.0
FL-1064-F55-D25 1064 55 25
FL-1064-F55-D31-T2.6 1064 55 31 2.6
FL-1064-F57-D27-T2.6 1064 57 27 2.3
FL-1064-F60-D23-T2.1 1064 60 23 2.1
FL-1064-F67-D23-T2.1 1064 67 23 2.1
FL-1064-F69-D23-T2.1 1064 69 23 2.1
FL-1064-F69-D24-T2.2 1064 69 24 2.2
FL-1064-F69-D31-T2.4 1064 69 31 2.4
FL-1064-F72-D36-T1.5 1064 72 36 1.5
FL-1064-F73-D36-T1.6 1064 73 36 1.6
FL-1064-F73-D35-T2.3 1064 73 36 2.3
FL-1064-F75-D25-T3 1064 75 25 3.0
FL-1064-F75-D30 1064 75 30
FL-1064-F75-D32-T3.0 1064 75 32 3.0
FL-1064-F79-D22-T3.5 1064 79 22 3.5
FL-1064-F79-D28-T3.0 1064 79 28 3.0

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 14
 Sintec Optronics Technology Pte Ltd

FL-1064-F79-D34-T2.5 1064 79 34 2.5

FL-1064-F80-D25-T2.3 1064 80 25 2.3
FL-1064-F80-D50-T2.7 1064 80 50 2.7
FL-1064-F81-D50-T2.7 1064 81 50 2.7
FL-1064-F82-D36-T2.4 1064 82 36 2.4
FL-1064-F83-D23-T2.1 1064 83 23 2.1
FL-1064-F85-D31-T2.1 1064 85 31 2.1
FL-1064-F86-D23-T2.3 1064 86 23 2.3
FL-1064-F87-D23-T4.5 1064 87 23 4.5
FL-1064-F87-D25-T4.2 1064 87 25 4.2
FL-1064-F87-D31-T3.2 1064 87 31 3.2
FL-1064-F87-D36-T2.2 1064 87 36 2.2
FL-1064-F88-D48-T2.3 1064 88 48 2.3
FL-1064-F90-D31-T2.3 1064 90 31 2.3
FL-1064-F99-D36-T2.5 1064 99 36 2.5
FL-1064-F100-D25-T3 1064 100 25 3.0
FL-1064-F100-D31-T2.5 1064 100 31 2.5
FL-1064-F104-D35-T2.3 1064 104 35 2.3
FL-1064-F108-D35-T2.9 1064 108 35 2.9
FL-1064-F120-D31-T2.3 1064 120 31 2.3
FL-1064-F124-D22-T4.0 1064 124 22 4.0
FL-1064-F124-D27-T3.6 1064 124 27 3.6
FL-1064-F124-D48-T3.0 1064 124 48 3.0
FL-1064-F126-D53-T3.0 1064 126 53 3.0
FL-1064-F127-D25-T2.3 1064 127 25 2.3
FL-1064-F150-D40-T5.5 1064 150 40 5.5
FL-1064-F150-D50-T1.5 1064 150 50 1.5
FL-1064-F155-D27-T3.4 1064 155 27 3.4
FL-1064-F200-D20-T2.5 1064 200 20 2.5
FL-1064-F200-D25-T2.5 1064 200 25 2.5 Ex stock
FL-1064-F250-D25-T2.5 1064 250 25 2.5 Ex stock
FL-1064-F833-D24-T2.1 1064 833 24 2.1
532nm coating is also available for above dimensions and thus thie part numbes will be FL-532-xxx etc.

2. Multi-element Focusing Lenses

Multi-element focusing lens consists of a few lenses to obtain better image quality and smaller focused
beam diameters. It is mainly used in laser scribing, engraving, laser XY-moving markin, laser welding
etc.

Part number description: FLM-xxxx-F-N-D-yy

FLM: multi-element focusing lens
Xxxx: laser wavelength, 1064nm, 532nm, 10.6um etc.
F: focal length, mm
N: number of lenses
D: outside diameter, mm
yy: others

(1) XD Series Multi-element Focusing Lenses

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 15
 Sintec Optronics Technology Pte Ltd

LFM-1064-N2-F76- LFM-1064-N3-F72- LFM-1064-N5-F75-

Part number
D44-XD D54-XD D60-XD
Number of lenses 2 3 5
Focal length (mm) 75.772 72.122 75.202
Working distance (mm) 68.437 66.759 56.911
Input aperture (mm) Φ24 Φ30 Φ30
Wavelength (mm) 1064 1064 1064
Transmittance >95% >95% >90%
Focused beam dia. (mm) <0.01 <0.01 <0.01
Connection (mm) M39×1 M48×1 M56×0.75
Dimension (AxBxC, mm) 44x16x36 54x25x44 60x42x56

Part number LFM-532-N2-F76-D44-XD LFM-532-N3-F72-D54-XD

Number of lenses 2 3
Focal length (mm) 75.772 72.122
Working distance (mm) 68.437 66.759
Input aperture (mm) Φ24 Φ30
Wavelength (mm) 532 532
Transmittance >95% >95%
Focused beam dia. (mm) <0.01 <0.01
Connection (mm) M39×1 M48×1
Dimension (AxBxC, mm) 44x16x36 54x25x44

(2) TK Series Multi-element Focusing Lenses

WL FL Aperture Diffraction WD D L Connection

Part number
nm mm mm Spot, um mm mm mm M
LFM-1064-N3-F78-D60-TK 1064 78 43 11 64.7 60 39.6 M56×1
LFM-1064-F80-D60-TK* 1064 80 40 4 69.5 60 45 M56×1
LFM-1064-N5-F80-D62-TK 1064 80 40 4 69.5 62 42.5 M58×1
LFM-1064-N3-F62-D60-TK 1064 61.7 43 10 46.7 60 37 M56×1
LFM-532-N3-F75-D60-TK 532 74 43 12 60.7 60 39.6 M56×1
LFM-532-N3-F80-D60-TK 532 80 40 10 49.5 60 39.6 M56×1
LFM-532-N5-F80-D60-TK 532 80 40 10 64.5 60 42.5 M56×1
LFM-532-N5-F80-D62-TK 532 80 40 10 64.5 62 42.5 M58×1
LFM-355-N3-F45-D32-TK 355 45 15 8 37.3 32 24 M30×0.75
LFM-355-N3-F60-D32-TK 355 60 22 8 52.4 32 28 M30×0.75
WL: wavelength; FL: focal length; WD: working distance; D: outside diameter.
* Non-spherical lenses.

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 16
 Sintec Optronics Technology Pte Ltd

CO2 Laser Focusing Lenses (Plano-Convex Lenses )

Specifications: Standards
Material quality Laser Grade without boundaries and visible inclusions
Diameter : 5 – 76.2 +0/-0.10 mm
Range of Sizes Edge Thickness : 2 – 12 +/-0.10 mm
Thickness (radiused) : 2 – 5 +/-0.05 mm
Range of Effective Focal Length (EFL) 12.7-254.0 +/- 2 %
Clear Aperture (polished) 90% of diameter
Plano: 1 fringe - 0.5 fringe per inch
Surface Figure (power-irregularity) at 0.63um
Radiused : varies dependent upon radius
Surface Quality: Scratch-Dig 40/20
AR Coating Reflectivity at 10.6 microns 0.25%

Description of Part Number:

FL-XXXX-F-D-T-EN-MN-YY
FL: single-element focusing lens
XXXX: laser wavelength, 10.6um.
F: focal length, mm
D: lens diameter, mm
T: lens edge thickness, mm
EN: Dimension unit is in inch (If there is no EN, it means
metric unit in mm).
MN: lens shape, MN means menicus, no MN means
plano-convex,
YY: others such as CC, UO, JS etc.
Coating: di-electric coating at 10.6Um.

FL BFL Dia. Edge T

Part number Material
mm/inch mm mm/inch mm
FL-10.6-5.0ZLP25 ZnSe 25 12.7/0.5 2.5
FL-10.6-F25.4-D12.7-JS ZnSe 25.4/1 12.7/0.5
FL-10.6-F40-D16-T2-CC ZnSe 40 39.1 16 2.0
FL-10.6-F40-D18-JS ZnSe 40 39.1 18
FL-10.6-F50-D16-T2-CC ZnSe 50 49.1 16 2.0
FL-10.6-F50-D18-JS ZnSe 50 49.1 18
FL-10.6-F50-D25-JS ZnSe 50 49.1 25
FL-10.6-F55-D20-JS ZnSe 55 20
FL-10.6-F60-D18-T2-CC ZnSe 60 59.1 18 2.0
FL-10.6-F60-D18-JS ZnSe 60 59.1 18
FL-10.6-F74-D30-T2.5-JS ZnSe 75 30 2.5
FL-10.6-F80-D25-T2.5-CC ZnSe 80 78.8 25 2.5
FL-10.6-F80-D25-JS ZnSe 80 78.8 25
FL-10.6-F95.25-D25.4-JS ZnSe 95.25/3.75 25.4/1.0
FL-10.6-15ZLP95-1106 ZnSe 95/3.75 38.05/1.5 3
FL-10.6-F100-D25-T2.5-CC ZnSe 100 98.9 25 2.5
FL-10.6-F100-D25-JS ZnSe 100 98.9 25
FL-10.6-F100-D25.4-WT ZnSe 100 98.9 25.4 3
FL-10.6-15ZLP100/7-10UM ZnSe 100 38.05/1.5 3
FL-10.6-F127-D27.95-JS ZnSe 127/5 27.95/1.1
FL-10.6-F127-D25.4-JS ZnSe 127/5 25.4/1.0
FL-10.6-11EX1ZLP127 ZnSe 127/5 28/1.1 3.17
FL-10.6-11PHGP127-BE ZnSe 127/5 28/1.1 4
FL-10.6-11ZLP127 ZnSe 127/5 28/1.1 3
FL-10.6-15HGPP127 ZnSe 127/5 38.05/1.5 6
FL-10.6-15PHGP127 ZnSe 127/5 38.05/1.5 7.6
FL-10.6-15ZLP127 ZnSe 127/5 38.05/1.5 3
FL-10.6-20PEHGP127 ZnSe 127/5 50.8/2 9.58
FL-10.6-20PHGP127 ZnSe 127/5 50.8/2 7.87
FL-10.6-15CIN130 ZnSe 130 38.05/1.5 7.1

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 17
 Sintec Optronics Technology Pte Ltd

FL-10.6-20CIN132 ZnSe 132 50.8/2 9.68

FL-10.6-15ZLP175 ZnSe 175 38.05/1.5 3
FL-10.6-6.7ZLP178 ZnSe 178 17 1.79
FL-10.6-15HGPP190 ZnSe 190/7.5 38.05/1.5 6
FL-10.6-20PEHGP190 ZnSe 190/7.5 50.8/2 9.58
FL-10.6-15EXZLP190 ZnSe 190/7.5 38.05/1.5 2
FL-10.6-20PHGP190 ZnSe 190.5/7.5 50.8/2 7.87
FL-10.6-15PHGP190 ZnSe 190.5/7.5 38.05/1.5 7.6
FL-10.6-15CIN194 ZnSe 194/7.64 38.05/1.5 7.1
FL-10.6-20CIN195 ZnSe 195/7.68 50.8/2 9.68
FL-10.6-20PHGP222 ZnSe 222/8.74 50.8/2 7.87
FL-10.6-20PHGP254 ZnSe 254/10 50.8/2 7.87
FL-10.6-11ZLP254 ZnSe 254/10 28 3
FL-10.6-5.9ZLP2800 ZnSe 280/10 15 2.5
FL-10.6-15HGPP381 ZnSe 381/15 38.05 6
FL-10.6-20ZLP1700 ZnSe 1700/66.9 50.8/2 3.5
FL-10.6-20PMGP15000 ZnSe 15000/590.5 50.8/2 4.06
1. FL=focal length; BFL-back focal length.
2. There are too many items and models and welcome to call us or send us an email if you have any
further enquiry or question!

LPZ Series Plano-convex ZnSe Lenses Coated AR-AR @ 10.6um

This wide range of CO2 plano-convex lenses have been prepared to fit most OEM, Industrial and
Medical laser systems. All have been manufactured to high-quality laser specifications for high-power
applications.

Made with laser grade zinc selenide with computer optimized anti-reflection coatings.

Specifications:
Material: ZnSe Laser Grade C.V.D. type
Diameter Tolerances: +0.000", -0.005"
Thickness: ±.010"
Surface Figure: < 1/40 wavelength @ 10.6µm
Centration: < 0.001"
Focal Length Tolerance: ±1.0%
Surface Quality: < 40/20 scratch-dig Laser Finish

Spectral Performance:
Standard AR Coating type Both Sides @ 10.6µm (AR)
Absorption: < 0.25 % total
Reflectance: < 0.20% per surface @ 10.6µm
Transmittance: > 99.0% typical
Ultra Low Absorption AR Coating type Both Sides @ 10.6µm (ULA)
Absorption: < 0.15 % total
Reflectance: < 0.25% per surface
Transmittance: > 99.0% typical
Dual Band AR Coating type Both Sides @ 10.6µm and .633µm (DBAR)
Absorption: < 0.30 % total
Reflectance: < 0.25% per surface @ 10.6µm
Transmittance: > 98.5% @ 10.6µm with > 90% @ .633µm

Model Number Diameter Focal Length Edge Thickness

FL-10.6-LZP-0710-DBAR 0.750" 1.00" 0.070"
FL-10.6-LZP-0715-DBAR 0.750" 1.50" 0.070"
FL-10.6-LZP-0720-DBAR 0.750" 2.00" 0.070"
FL-10.6-LZP-0720-ET2.0 0.750" 2.00" 0.080"
FL-10.6-LZP-0725-DBAR 0.750" 2.50" 0.070"
FL-10.6-LZP-0730-DBAR 0.750" 3.00" 0.070"
FL-10.6-LZP-0730-ET3.0 0.750" 3.00" 0.120"
FL-10.6-LZP-0735-DBAR 0.750" 3.50" 0.070"

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 18
 Sintec Optronics Technology Pte Ltd

FL-10.6-LZP-0740-DBAR 0.750" 4.00" 0.070"

FL-10.6-LZP-0750-DBAR 0.750" 5.00" 0.070"
FL-10.6-LZP-0775-DBAR 0.750" 7.50" 0.070"
FL-10.6-LZP-07A0-DBAR 0.750" 10.0" 0.070"
FL-10.6-LZP-07A2-DBAR 0.750" 12.0" 0.070"
FL-10.6-LZP-07A5-DBAR 0.750" 15.0" 0.070"
FL-10.6-LZP-07B0-DBAR 0.750" 20.0" 0.070"
FL-10.6-LZP-1010-ET2.0 1.00" 1.00" 0.080"
FL-10.6-LZP-1015-ET2.0 1.00" 1.50" 0.080"
FL-10.6-LZP-1025-ET3.0 1.00" 2.50" 0.120"
FL-10.6-LZP-1030-ET3.0 1.00" 3.00" 0.120"
FL-10.6-LZP-1035-ET3.0 1.00" 3.50" 0.120"
FL-10.6-LZP-1040-ET3.0 1.00" 4.00" 0.120"
FL-10.6-LZP-1050-ET3.0 1.00" 5.00" 0.120"
FL-10.6-LZP-1060-ET3.0 1.00" 6.00" 0.120"
FL-10.6-LZP-1075-ET3.0 1.00" 7.50" 0.120"
FL-10.6-LZP-10A0-ET3.0 1.00" 10.0" 0.120"
FL-10.6-LZP-10A5-ET3.0 1.00" 15.0" 0.120"
FL-10.6-LZP-10B0-ET3.0 1.00" 20.0" 0.120"
FL-10.6-LZP-10B5-ET3.0 1.00" 25.0" 0.120"
FL-10.6-LZP-1115-ET2.0 1.10" 1.50" 0.080"
FL-10.6-LZP-1125-ET3.0 1.10" 2.50" 0.120"
FL-10.6-LZP-1125-ET4.0 1.10" 2.50" 0.160"
FL-10.6-LZP-1125-ET6.0 1.10" 2.50" 0.236"
FL-10.6-LZP-1135-ET3.0 1.10" 3.50" 0.120"
FL-10.6-LZP-1138-ET3.0 1.10" 3.75" 0.120"
FL-10.6-LZP-1138-ET4.0 1.10" 3.75" 0.160"
FL-10.6-LZP-1150-ET3.0 1.10" 5.00" 0.120"
FL-10.6-LZP-1150-ET4.0 1.10" 5.00" 0.160"
FL-10.6-LZP-1150-ET6.0 1.10" 5.00" 0.236"
FL-10.6-LZP-1160-ET3.0 1.10" 6.00" 0.120"
FL-10.6-LZP-1175-ET3.0 1.10" 7.50" 0.120"
FL-10.6-LZP-1175-ET6.0 1.10" 7.50" 0.236"
FL-10.6-LZP-11A0-ET3.0 1.10" 10.0" 0.120"
FL-10.6-LZP-1525-ET3.0 1.500" 2.50" 0.120"
FL-10.6-LZP-1525-ET4.0 1.500" 2.50" 0.160"
FL-10.6-LZP-1530-ET3.0 1.500" 3.00" 0.120"
FL-10.6-LZP-1535-ET3.0 1.500" 3.50" 0.120"
FL-10.6-LZP-1538-ET3.0 1.500" 3.75" 0.120"
FL-10.6-LZP-1540-ET3.0 1.500" 4.00" 0.120"
FL-10.6-LZP-1550-ET2.0 1.500" 5.00" 0.080"
FL-10.6-LZP-1550-ET3.0 1.500" 5.00" 0.120"
FL-10.6-LZP-1550-ET4.0 1.500" 5.00" 0.160"
FL-10.6-LZP-1550-ET5.0 1.500" 5.00" 0.200"
FL-10.6-LZP-1550-ET6.0 1.500" 5.00" 0.236"
FL-10.6-LZP-1550-ET7.6 1.500" 5.00" 0.300"
FL-10.6-LZP-1551-ET7.0 1.500" 5.13" 0.280"
FL-10.6-LZP-1560-ET3.0 1.500" 6.00" 0.120"
FL-10.6-LZP-1574-ET7.6 1.500" 7.45" 0.300"
FL-10.6-LZP-1575-ET3.0 1.500" 7.50" 0.120"
FL-10.6-LZP-1575-ET4.0 1.500" 7.50" 0.160"
FL-10.6-LZP-1575-ET6.0 1.500" 7.50" 0.236"
FL-10.6-LZP-1575-ET7.6 1.500" 7.50" 0.300"
FL-10.6-LZP-1576-ET7.6 1.500" 7.63" 0.300"
FL-10.6-LZP-15A0-ET2.0 1.500" 10.0" 0.080"
FL-10.6-LZP-15A0-ET4.0 1.500" 10.0" 0.160"
FL-10.6-LZP-15A0-ET6.0 1.500" 10.0" 0.160"
FL-10.6-LZP-15A5-ET3.0 1.500" 15.0" 0.120"
FL-10.6-LZP-15B0-ET3.0 1.500" 20.0" 0.120"
FL-10.6-LZP-15B5-ET3.0 1.500" 25.0" 0.120"
FL-10.6-LZP-15C9-ET3.0 1.500" 39.3" 0.120"

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 19
 Sintec Optronics Technology Pte Ltd

FL-10.6-LZP-15E9-ET3.0 1.500" 59.0" 0.120"

FL-10.6-LZP-15X9-ET4.0 1.500" 59.0" 0.160"
FL-10.6-LZP-2050-ET7.6 2.00" 5.0" 0.300"
FL-10.6-LZP-2050-ET9.7 2.00" 5.0" 0.380"
FL-10.6-LZP-2051-ET9.7 2.00" 5.188" 0.380"
FL-10.6-LZP-2074-ET7.9 2.00" 7.45" 0.310"
FL-10.6-LZP-2074-ET9.7 2.00" 7.45" 0.380"
FL-10.6-LZP-2075-ET2.5 2.00" 7.50" 0.100"
FL-10.6-LZP-2075-ET4.9 2.00" 7.50" 0.193"
FL-10.6-LZP-2075-ET7.9 2.00" 7.50" 0.310"
FL-10.6-LZP-2075-ET9.7 2.00" 7.50" 0.380"
FL-10.6-LZP-2076-ET7.6 2.00" 7.560" 0.300"
FL-10.6-LZP-2076-ET9.7 2.00" 7.673" 0.380"
FL-10.6-LZP-2088-ET8.0 2.00" 8.75" 0.315"
FL-10.6-LZP-20A0-ET4.7 2.00" 10.0" 0.185"
FL-10.6-LZP-20A0-ET9.7 2.00" 10.0" 0.380"
FL-10.6-LZP-20A3-ET8.0 2.00" 12.50" 0.315"
FL-10.6-LZP-2588-ET7.87 2.00" 8.75" 0.310"

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 20
 Sintec Optronics Technology Pte Ltd

CO2 Laser Focusing Lenses (Meniscus Lenses)

Positive meniscus lenses may be used to increase the numerical aperture of a positive lens assembly
without an undue increase in the aberrations.

The For the case of a lens of thickness tc in air, and

surfaces with radii of curvature R1 and R2, the
effective focal length f is given by:

⎡1 1 t c (n − 1) ⎤
= (n − 1) • ⎢ −
1
+ ⎥
f ⎣ R1 R2 nR1 R2 ⎦

where n is the refractive index of the lens medium.

The quantity 1/f is also known as the optical power of
the lens. The the back focal distance:

⎡ t (n − 1) ⎤
BFL = f • ⎢1 − c ⎥
⎣ nR1 ⎦

In the sign convention used here, the value of R1 will be positive if the first lens surface is convex, and
negative if it is concave. The value of R2 is positive if the second surface is concave, and negative if
convex. Note that sign conventions vary between different authors, which results in different forms of
these equations depending on the convention used.

Meniscus lenses form the largest and most popular part of our product range.

z Optimised meniscus designs

z Manufactured in high quantities to keep costs low.
z Quality matches or exceeds any other supplier

Specifications:
Diameter tolerance: +0/-0.1mm
Focal length tolerance: +/-0.5%
Angle of incidence: 0 degree
Transmission: >99.4%
Reflectance: <0.1% per surface
Absorption: <0.2% per surface

The following standard meniscus are available.

Diameter ET FL
Part No. Material Coating
mm mm mm
FL-10.6-5.0ZLF25 ZnSe 12.7 2 AR/AR 25.4
FL-10.6-5.0ZLF38 ZnSe 12.7 2 AR/AR 38.1
FL-10.6-F38.1-D12.7-T2-MN-WT ZnSe 12.7 2 AR/AR 38.1
FL-10.6-5.1ZLF100 ZnSe 13 2 AR/AR 100
FL-10.6-F100-D13-T2-MN-WT ZnSe 13 2 AR/AR 100
FL-10.6-6.1ZLF48 ZnSe 15.5 2.5 AR/AR 48
FL-10.6-6.1ZLF110 ZnSe 15.5 2.5 AR/AR 110
FL-10.6-10ZLF25 ZnSe 25.4 2.5 AR/AR 25.4
FL-10.6-10ZLF38 ZnSe 25.4 2.5 AR/AR 38.1
FL-10.6-10ZLF51 ZnSe 25.4 2.5 AR/AR 50.8
FL-10.6-10ZLF63 ZnSe 25.4 2.5 AR/AR 63.5
FL-10.6-10ZLF76 ZnSe 25.4 2.5 AR/AR 76.2
FL-10.6-10ZLF95 ZnSe 25.4 2.5 AR/AR 95.3
FL-10.6-10ZLF102 ZnSe 25.4 2.5 AR/AR 101.6
FL-10.6-10ZLF110 ZnSe 25.4 2.5 AR/AR 110
FL-10.6-10ZLF127 ZnSe 25.4 2.5 AR/AR 127
FL-10.6-F127-D25.4-T2.5-MN-WT ZnSe 25.4 2.5 AR/AR 127

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 21
 Sintec Optronics Technology Pte Ltd

FL-10.6-10ZLF152 ZnSe 25.4 2.5 AR/AR 152

FL-10.6-F152-D25.4-T2.5-MN-WT ZnSe 25.4 2.5 AR/AR 152
FL-10.6-10ZLF200 ZnSe 25.4 2.5 AR/AR 200
FL-10.6-10ZLF221 ZnSe 25.4 2.24 AR/AR 221
FL-10.6-10ZLF508 ZnSe 25.4 2.5 AR/AR 508
FL-10.6-11ZLF25 ZnSe 28 3 AR/AR 25.4
FL-10.6-11GLF38 GaAs 28 2.5 Uncoated 38
FL-10.6-11ZLF38 ZnSe 28 3 AR/AR 38.1
FL-10.6-11ZLF50 ZnSe 28 3 AR/AR 50.8
FL-10.6-11HGP50 ZnSe 28 4.2 AR/AR 50.8
FL-10.6-11HGP63 ZnSe 28 4.2 AR/AR 63.5
FL-10.6-11ZLF63 ZnSe 28 3 AR/AR 63.5
FL-10.6-11GLC63 GaAs 28 1.8 AR/AR 63.5
FL-10.6-11ZLF76 ZnSe 28 3 AR/AR 76.2
FL-10.6-11ZLF89 ZnSe 28 3 AR/AR 89
FL-10.6-11ZLF90 ZnSe 28 3 AR/AR 90
FL-10.6-11ZLF95 ZnSe 28 3 AR/AR 95.3
FL-10.6-11HGP95 ZnSe 28 4.2 AR/AR 95.3
FL-10.6-11ZLF100 ZnSe 28 3 AR/AR 100
FL-10.6-11ZLF102 ZnSe 28 3 AR/AR 102
FL-10.6-11ZLF110 ZnSe 28 3 AR/AR 110
FL-10.6-11ZLF127 ZnSe 28 3 AR/AR 127
FL-10.6-11EHGP127 ZnSe 28 6.2 AR/AR 127
FL-10.6-11HGP127 ZnSe 28 4.2 AR/AR 127
FL-10.6-11HLF152 ZnSe 28 3 AR/AR 152
FL-10.6-11HLF190 ZnSe 28 3 AR/AR 190.5
FL-10.6-11HGP190 ZnSe 28 4.2 AR/AR 190.5
FL-10.6-11HLF254 ZnSe 28 3 AR/AR 254
FL-10.6-11HLF762 ZnSe 28 3 AR/AR 762
FL-10.6-11.8HLF750 ZnSe 30 3 AR/AR 750
FL-10.6-12.6HGP89 ZnSe 32 4.2 AR/AR 89
FL-10.6-VTE375 ZnSe 38.05 7.4 AR/AR 95.3
FL-10.6-VTE500 ZnSe 38.05 7.4 AR/AR 127
FL-10.6-VTE750 ZnSe 38.05 7.4 AR/AR 190.5
FL-10.6- VTE900 ZnSe 38.05 7.4 AR/AR 228.6
FL-10.6- VTE1000 ZnSe 38.05 7.4 AR/AR 254
FL-10.6-15ZLF38 ZnSe 38.05 2.4 AR/AR 38.1
FL-10.6-15ZLF50 ZnSe 38.05 3 AR/AR 50.8
FL-10.6-15HGP63 ZnSe 38.05 6.1 AR/AR 63.5
FL-10.6-15ZLF63 ZnSe 38.05 3 AR/AR 63.5
FL-10.615ZLF75 ZnSe 38.05 2.93 AR/AR 75
FL-10.6-15ZLF76 ZnSe 38.05 3 AR/AR 76.2
FL-10.6-15ZLF80 ZnSe 38.05 3 AR/AR 80
FL-10.6-15ZLF89 ZnSe 38.05 3 AR/AR 89
FL-10.6-15HGP95 ZnSe 38.05 6 AR/AR 95
FL-10.6-15ZLF95 ZnSe 38.05 3 AR/AR 95.3
FL-10.6-15ZLF100 ZnSe 38.05 3 AR/AR 100
FL-10.6-15ZLF127 ZnSe 38.05 3 AR/AR 127
FL-10.6-15EHGP127 ZnSe 38.05 7.8 AR/AR 127
FL-10.6-15HGP127 ZnSe 38.05 6.2 AR/AR 127
FL-10.6-15BYS127 ZnSe 38.05 9 AR/AR 127.1
FL-10.6-15HGP150 ZnSe 38.05 6.2 AR/AR 150
FL-10.6-15ZLF152 ZnSe 38.05 3 AR/AR 152
FL-10.6-15EHGP190-BE ZnSe 38.05 7.87 AR/AR 190
FL-10.6-15HGP190 ZnSe 38.05 6.1 AR/AR 190.5
FL-10.6-15ZLF190 ZnSe 38.05 3 AR/AR 190.5
FL-10.6-15BYS190 ZnSe 38.05 9 AR/AR 190.7
FL-10.6-15BYS196 ZnSe 38.05 9 AR/AR 196
FL-10.6-15HGP254 ZnSe 38.05 6.3 AR/AR 254
FL-10.6-15ZLF254 ZnSe 38.05 3 AR/AR 254
FL-10.6-15ZLF345 ZnSe 38.05 3 AR/AR 345

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 22
 Sintec Optronics Technology Pte Ltd

FL-10.6-15ZLF508 ZnSe 38.05 3 AR/AR 508

FL-10.6-15ZLF750 ZnSe 38.05 3.06 AR/AR 750
FL-10.6-17.5HGP127 ZnSe 44.45 9 AR/AR 127
FL-10.6-17.5HGP190 ZnSe 44.45 9 AR/AR 190
FL-10.6-17.5ZLF127 ZnSe 44.5 3.5 AR/AR 127
FL-10.6-19.7GEN125 Ge 50 1.5 AR/AR-Ge 125
FL-10.6-19.7ZLF127 ZnSe 50 3.5 AR/AR 127
FL-10.6-19.7EHGP150 ZnSe 50 9.6 AR/AR 150
FL-10.6-20EHGP95 ZnSe 50.8 9.6 AR/AR 95
FL-10.6-20HGP127 ZnSe 50.8 7.87 AR/AR 127
FL-10.6-20ZLF127 ZnSe 50.8 3.5 AR/AR 127
FL-10.6-20EHGP127 ZnSe 50.8 9.6 AR/AR 127
FL-10.6-20EHGP190 ZnSe 50.8 9.6 AR/AR 190.5
FL-10.6- 20ZLF190 ZnSe 50.8 3.5 AR/AR 190.5
FL-10.6-20EHGP198 ZnSe 50.8 9.62 AR/AR 198
FL-10.6-20EHGP254 ZnSe 50.8 9.6 AR/AR 254
FL-10.6-20GEM254 Ge 50.8 4 AR/AR-DUR 254

LMZ Series Meniscus ZnSe Lenses Coated AR-AR @ 10.6 µm

This wide range of CO2 plano-convex lenses have been prepared to fit most OEM, Industrial and
Medical laser systems. All have been manufactured to high-quality laser specifications for high-power
applications.

Made with laser grade zinc selenide with computer optimized anti-reflection coatings.

Specifications:
Material: ZnSe Laser Grade C.V.D. type
Diameter Tolerances: +0.000", -0.005"
Thickness: ±0.010"
Surface Figure: < 1/40 wavelength @ 10.6µm
Centration: < 0.001"
Focal Length Tolerance: ±1.0%
Surface Quality: < 40/20 scratch-dig Laser Finish

Spectral Performance:
Standard AR Coating type Both Sides @ 10.6µm (AR)
Absorption: < 0.25 % total
Reflectance: < 0.20% per surface @ 10.6µm
Transmittance: > 99.0% typical
Ultra Low Absorption AR Coating type Both Sides @ 10.6µm (ULA)
Absorption: < 0.15 % total
Reflectance: < 0.25% per surface
Transmittance: > 99.0% typical
Dual Band AR Coating type Both Sides @ 10.6µm and .633µm (DBAR)
Absorption: < 0.30 % total
Reflectance: < 0.25% per surface @ 10.6µm
Transmittance: > 98.5% @ 10.6µm with > 90% @ .633µm

Model Number Diameter Focal Length Edge Thickness

FL-10.6-LMZ-0707-ET2.0 0.750" 0.750" 0.080"
FL-10.6-LMZ-0710-ET2.0 0.750 1.00 0.080
FL-10.6-LMZ-0712-ET2.0 0.750 1.20 0.080
FL-10.6-LMZ-0715-ET2.0 0.750 1.50 0.080
FL-10.6-LMZ-0720-ET2.0 0.750 2.00 0.080
FL-10.6-LMZ-0725-ET2.0 0.750 2.50 0.080
FL-10.6-LMZ-0730-ET2.0 0.750 3.00 0.080
FL-10.6-LMZ-0740-ET2.0 0.750 4.00 0.080
FL-10.6-LMZ-1010-ET2.0 1.00 1.00 0.080
FL-10.6-LMZ-1015-ET3.0 1.00 1.50 0.120
FL-10.6-LMZ-1020-ET3.0 1.00 2.0 0.120
FL-10.6-LMZ-1030-ET3.0 1.00 3.00 0.120

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 23
 Sintec Optronics Technology Pte Ltd

FL-10.6-LMZ-1050-ET3.0 1.00 5.00 0.120

FL-10.6-LMZ-1075-ET3.0 1.00 7.50 0.120
FL-10.6-LMZ-1115-ET2.8 1.10 1.50 0.110
FL-10.6-LMZ-1125-ET3.0 1.10 2.50 0.120
FL-10.6-LMZ-1125-ET6.0 1.10 2.50 0.236
FL-10.6-LMZ-1135-ET3.0 1.10 3.50 0.120
FL-10.6-LMZ-1138-ET2.8 1.10 3.75 0.110
FL-10.6-LMZ-1138-ET3.0 1.10 3.75 0.120
FL-10.6-LMZ-1150-ET2.8 1.10 5.0 0.110
FL-10.6-LMZ-1150-ET3.0 1.10 5.0 0.120
FL-10.6-LMZ-1150-ET4.0 1.10 5.0 0.160
FL-10.6-LMZ-1150-ET6.0 1.10 5.0 0.236
FL-10.6-LMZ-1175-ET2.8 1.10 7.50 0.110
FL-10.6-LMZ-1175-ET4.0 1.10 7.50 0.160
FL-10.6-LMZ-1175-ET6.0 1.10 7.50 0.236
FL-10.6-LMZ-11A0-ET2.8 1.10 10.0 0.110
FL-10.6-LMZ-1520-ET3.0 1.50 2.0 0.120
FL-10.6-LMZ-1525-ET6.0 1.50 2.50 0.236
FL-10.6-LMZ-1530-ET3.0 1.50 3.0 0.120
FL-10.6-LMZ-1538-ET6.0 1.50 3.8 0.236
FL-10.6-LMZ-1538-ET7.4 1.50 3.8 0.291
FL-10.6-LMZ-1550-ET3.0 1.50 5.0 0.120
FL-10.6-LMZ-1550-ET4.0 1.50 5.0 0.160
FL-10.6-LMZ-1550-ET6.0 1.50 5.0 0.236
FL-10.6-LMZ-1550-ET7.4 1.50 5.0 0.291
FL-10.6-LMZ-1550-ET9.0 1.50 5.0 0.354
FL-10.6-LMZ-1575-ET6.0 1.50 7.50 0.236
FL-10.6-LMZ-1575-ET7.4 1.50 7.50 0.291
FL-10.6-LMZ-1575-ET9.0 1.50 7.50 0.354
FL-10.6-LMZ-1590-ET7.4 1.50 9.0 0.291
FL-10.6-LMZ-15A0-ET7.4 1.50 10.0 0.291
FL-10.6-LMZ-2050-ET9.7 2.0 5.0 0.380
FL-10.6-LMZ-2075-ET9.7 2.0 7.50 0.380
FL-10.6-LMZ-20A0-ET9.7 2.0 10.0 0.380

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 24
 Sintec Optronics Technology Pte Ltd

CO2 Laser Focusing Lenses (Plano-Concave Lenses )

Specifications:
Material: ZnSe Laser Grade C.V.D. type
Diameter Tolerances: +0.000", -0.005"
Thickness: ±.010"
Surface Figure: < 1/40 wavelength @ 10.6µm
Centration: < 0.001"
Focal Length Tolerance: ±1.0%
Surface Quality: < 40/20 scratch-dig Laser Finish

Spectral Performance:
Standard AR Coating type Both Sides @ 10.6µm (AR)
Absorption: < 0.25 % total
Reflectance: < 0.20% per surface @ 10.6µm
Transmittance: > 99.0% typical
Ultra Low Absorption AR Coating type Both Sides @ 10.6µm (ULA)
Absorption: < 0.15 % total
Reflectance: < 0.25% per surface
Transmittance: > 99.0% typical
Dual Band AR Coating type Both Sides @ 10.6µm and .633µm (DBAR)
Absorption: < 0.30 % total
Reflectance: < 0.25% per surface @ 10.6µm
Transmittance: > 98.5% @ 10.6µm with > 90% @ .633µm

WL FL BFL Dia. Edge T

Part number
um mm/inch mm mm/inch mm
FL-10.6-F(20)-D12-T2.0-CC 10.6 -20mm -20.6 12 2.0

Model Number Diameter Focal Length Edge Thickness

FL-10.6-LPCZ-0510-ET3.2 0.500" -1.000" 0.125"
FL-10.6-LPCZ-0514-ET2.5 0.500" -1.390" 0.100"
FL-10.6-LPCZ-0520-ET2.0 0.500" -2.000" 0.080"
FL-10.6-LPCZ-0525-ET2.5 0.500" -2.500" 0.100"
FL-10.6-LPCZ-0540-ET2.5 0.500" -4.000" 0.100"
FL-10.6-LPCZ-0610-ET4.6 0.600" -1.000" 0.180"
FL-10.6-LPCZ-0620-ET3.0 0.600" -2.000" 0.120"
FL-10.6-LPCZ-0625-ET3.0 0.600" -2.500" 0.120"
FL-10.6-LPCZ-0640-ET2.4 0.600" -4.000" 0.095"
FL-10.6-LPCZ-0710-ET5.0 0.750" -1.000" 0.200"
FL-10.6-LPCZ-0715-ET2.0 0.750" -1.500" 0.080"
FL-10.6-LPCZ-0720-ET2.5 0.750" -2.000" 0.100"
FL-10.6-LPCZ-0725-ET2.5 0.750" -2.500" "0.100
FL-10.6-LPCZ-0750-ET2.0 0.750" -5.000" 0.080"
FL-10.6-LPCZ-1014-ET5.0 1.000" -1.390" 0.200"
FL-10.6-LPCZ-1025-ET4.0 1.000" -2.500" 0.160"
FL-10.6-LPCZ-1115-ET5.0 1.100" -1.500" 0.200"
FL-10.6-LPCZ-1125-ET4.0 1.100" -2.500" 0.160"
FL-10.6-LPCZ-1150-ET3.0 1.100" -5.000" 0.120"

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 25
 Sintec Optronics Technology Pte Ltd

CO2 Laser Focusing Lenses (Aspheric Lenses)

Aspheric Lenses are intended as single-element alternatives to the doublet series and high-
performance alternatives to short focal length meniscus lenses.

z Diffraction limited performance by correcting the spherical aberration that is present with a "best
form" meniscus lens
z More tolerant to small angular misalignments of the beam than plano-convex lenses
z Can be supplied mounted if required

Specifications:
z Diameter tolerance: +0/-0.1mm
z Focal length tolerance: ±0.5%
z Transmission: >99.4%
z Reflectance: 0.1% per surface
z Absorption per surface: Typically <0.2%

Part No. Material Diameter ET Coating FL

LF-10.6-10ZAL25.4 ZnSe 25.4mm 3mm AR/AR 25.4mm
LF-10.6-11ZAL25.4 ZnSe 28mm 3mm AR/AR 25.4mm
LF-10.6-11ZAL38.1 ZnSe 28mm 3mm AR/AR 38.1mm
LF-10.6-11ZAL50.8 ZnSe 28mm 3mm AR/AR 50.8mm
LF-10.6-11ZAL63.5 ZnSe 28mm 3mm AR/AR 63.5mm
LF-10.6-15ZAL127 ZnSe 38.05mm 3mm AR/AR 127mm
LF-10.6-15ZAL38.1 ZnSe 38.05mm 3mm AR/AR 38.1mm
LF-10.6-15ZAL50.8 ZnSe 38.05mm 3mm AR/AR 50.8mm
LF-10.6-15ZAL63.5 ZnSe 38.05mm 3mm AR/AR 63.5mm
LF-10.6-15ZAL95.3 ZnSe 38.05mm 3mm AR/AR 95.3mm

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 26
 Sintec Optronics Technology Pte Ltd

CO2 Laser Focusing Lenses Used in Branded Lasers

AMADA Focusing Lenses

Our Part No. Focusing Lenses Part Description
FL-10.6-F127-D38.1-T7.62 (PL-CX) Dia. 1.5" / FL: 5.0" / ET: .300" (7.62mm)
FL-10.6-F190.5-D38.1-T8 (PL-CX) Dia. 1.5" / FL: 7.5" / ET: .315" (8.00mm)
FL-10.6-F127-D50.8-T7.87 (PL-CX) Dia. 2.0" / FL: 5.0" / ET: .310" (7.87mm)
FL-10.6-F190.5-D50.8-T9.65 (PL-CX) Dia. 2.0" / FL: 7.5" / ET: .380" (9.65mm)
FL-10.6-F190.5-D50.8-T7.87 (PL-CX) Dia. 2.0" / FL: 7.5” / ET: .310" (7.87mm)

Bystronic Focusing Lenses

Our Part No. Focusing Lenses Part Description
FL-10.6-F127-D38.1-T5.99-MN (Men) Dia. 1.5" / FL: 5.0" / ET: .236" (5.99mm)
FL-10.6-F127-D38.1-T8.99-MN (Men) Dia. 1.5" / FL: 5.0" / ET: .354" (8.99mm)
FL-10.6-F190.5-D38.1-T5.99-MN (Men) Dia. 1.5" / FL: 7.5" / ET: .236" (5.99mm)
FL-10.6-F190.5-D38.1-T8.99-MN (Men) Dia. 1.5" / FL: 7.5" / ET: .354" (8.99mm

CINCINNATI Focusing Lenses

Our Part No. Focusing Lenses Part Description
FL-10.6-F130.3-D38.1-T7.11 (PL-CX) Dia. 1.5" / FL: 5.13” / ET: .280" (7.11mm)
FL-10.6-F193.8-D38.1-T7.62 (PL-CX) Dia. 1.5" / FL: 7.63" / ET: .300" (7.62mm)
FL-10.6-F190.5-D50.8-T9.65 (PL-CX) Dia. 2.0" / FL: 7.50" / ET: .380" (9.65mm)
FL-10.6-F127-D50.8-T9.65 (PL-CX) Dia. 2.0" / FL: 5.00"/ ET: .380" (9.65mm)

MAZAK Focusing Lenses

Our Part No. Focusing Lenses Part Description
FL-10.6-F127-D38.1-T5.99 (PL-CX) Dia. 1.5" / FL: 5.0" / ET: .236" (5.99mm)
FL-10.6-F127-D38.1-T7.97 (PL-CX) Dia. 1.5" / FL: 5.0" / ET: .310" (7.97mm)
FL-10.6-F127-D50.8-T7.87 (PL-CX) Dia. 2.0" / FL: 5.0" / ET: .314" (7.87mm)
FL-10.6-F127-D50.8-T9.65 (PL-CX) Dia. 2.0" / FL: 5.0" / ET: .380" (9.65mm)
FL-10.6-F190.5-D50.8-T7.87 (PL-CX) Dia. 2.0" / FL: 7.5" / ET: .314" (7.87mm)
FL-10.6-F190.5-D50.8-T9.65 (PL-CX) Dia. 2.0" / FL: 7.5” / ET: .380" (9.65mm)

Mitsubishi Focusing Lenses

Our Part No. Part Description
FL-10.6-F190.5-D50.8-T7.87 (PL-CX) Dia. 2.0" / FL: 7.5” / ET: .310" (7.87mm)
FL-10.6-F190.5-D38.1-T8 (PL-CX) Dia. 1.5" / FL: 7.5" / ET: .315" (8.00mm)
FL-10.6-F127-D50.8-T7.87 (PL-CX) Dia. 2.0" / FL: 5.0" / ET: .310" (7.87mm)
FL-10.6-F190.5-D50.8-T7.87 (PL-CX) Dia. 2.0" / FL: 7.5"/ ET: .310" (7.87mm)
FL-10.6-F190.5-D50.8-T9.65 (PL-CX) Dia. 2.0" / FL: 7.5"/ ET: .380" (9.65mm)

TRUMPF Focusing Lenses

Our Part No. Part Description
FL-10.6-F127-D38.1-T7.39-MN (Meniscus) Dia. 1.5" / FL: 5.0" / ET: .291" (7.39mm)
FL-10.6-F190.5-D38.1-T7.39-MN (Meniscus) Dia. 1.5" / FL: 7.5" / ET: .291" (7.39mm)
FL-10.6-F190.5-D38.1-T7.62 (PL-CX) Dia. 1.5" / FL: 7.5" / ET: .300" (7.62mm)
FL-10.6-F190.5-D38.1-T7.75 (PL-CX) Dia. 1.5" / FL: 7.5" / ET: .305" (7.75mm)
FL-10.6-F127-D38.1-T6.2 (PL-CX) Dia. 1.5" / FL: 5.0" / ET: .244" (6.20mm)

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 27
 Sintec Optronics Technology Pte Ltd

Dual-Focus Lenses (Bi-focal Lenses)

Dual-Focus lenses are a revolutionary new type of lens for CO2 laser cutting, which can be supplied as
a direct replacement for your conventional lens. Dual-Focus lenses can allow much thicker materials to
be cut at a given laser power. Additional advantages come from the fact that assist gas requirements
are significantly reduced.

Advantages

z 50-100% faster cutting of existing materials

z Thicker materials may be cut
z Polished finishes can be achieved
z Elimination of sub-surface dross
z Cost savings on assist gas
z Immediate cut initiation with no top surface dross
z Reduced sensitivity to errors in setting the focus
z Direct replacement of existing lenses

How Do Dual-Focus Lenses Work?

By distributing a fraction of the laser energy into a secondary (lower) focus, the lenses provide faster,
cleaner cuts, with easier initiation and the elimination of sub-surface dross.

The laser beam is intercepted an focused by a lens having a central circular region with a focal length
which is longer than the basic lens focal length. The secondary focal area is used to produce the
concentration of laser energy further into the material, while the energy intercepted by the outer part of
the lens produces the ‘upper’ focus. The splitting of the laser power into two foci allows a more efficient
couple of the energy into the cutting process; the lower focus being directed into the kerf. This results is
high energy density and increased localised temperature at both the upper and the lower foci.

Technical considerations

The introduction of the secondary focal area introduces two new variables to the focusing lens:
(1) The difference in focal lengths between the basic lens and the secondary focal area needs to be
‘tailored’ to or smaller than the thickness of material to be cut. In general, the thicker the material,
the greater should be the difference in F (called dF).
(2) The diameter of the secondary focal area (called 2h), in relation to the diameter of the incident beam,
determines the fraction of beam energy directed to the lower focus.

The propagation calculations for the beams forming the two foci can be approximated by the application
of Gaussian formulae.

An increase in the diameter of the secondary focal area has two effects:
(a) Increases the fraction of energy directed to the lower focus
(b) Reduces the focused waist diameter, so increasing the lower focus energy density and reducing the
lower focus depth-of-focus.

For a TEM00 beam of (1/e2) diameter 2w, intercepted by a secondary focal area of diameter 2h, the
fraction of beam energy directed to the top and bottom focus are:
http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 28
 Sintec Optronics Technology Pte Ltd

Fraction to top focus = exp[-2(h/w)2]

Fraction to bottom focus = 1 - exp[-2(h/w)2]

Applications
Successful applications include:
* Cutting thick-section metals, including stainless steel and aluminium.
* Improved die-board processing (with better process control).
* Scribing/processing thick-section ceramics.

Important note: when cutting stainless steel the (main) upper lens focus must be set near to the top
material surface!

Dual-Focus product types

The main ranges of Dual-Focus lenses are:

FLDF-10.6-D28-T4.2 Series (1.1"dia 4.2mm ET lenses, 127 & 190mm FLs)
FLDF-10.6-D38-T6.2 Series (1.5"dia 6.2mm ET lenses, 127, 190 & 254mm FLs)
FLDF-10.6-D38-T7.4 Series (1.5"dia 7.4mm ET lenses, 127, 190 & 254mm FLs)
FLDF-10.6-D38-T9 (1.5"dia 9.0mm ET lenses, 127, 190 & 254mm FLs)
FLDF-10.6-D50.8-T9.6 Series (2.0"dia 9.6mm ET lenses, 127 & 190mm FLs)

Applications guideline

Based on practical trials, the following broad guidelines are offered for those customers wishing to
make their own lens selection for cutting stainless steel:

z The diameter, edge thickness and focal length are chosen to match their current conventional lens.
dF is the thickness of material to be cut. If a range of thicknesses is specified, dF should be
towards the thinner end. If the range of thickness varies by more than a factor of 2, then perhaps
more than one lens is recommended.
z There is no clear rule as to what dF should be. Originally, it was
thought that one focus at the top surface and one at the bottom
(so dF = material thickness) would be the best, but it has never
been confirmed. The right picture shows the shape of the melt
front in metal (stainless steel) as it is being cut. It is not straight
down though the sheet but has a shoulder. This means that if the
bottom focus is put at the bottom surface, it will never actually get
to focus there, so the picture has targeted it roughly where the
shoulder will be. Dual-Focus lenses are about coupling the
energy more efficiently into the material and the conditions may
vary enough from one user to another that there are no hard
rules. In general, dF is smaller than the thickness of material and
the first focus is on the top surface.
z 2h is selected to be 50% of the 1/e2 beam diameter if the beam mode is a good ‘00’ Gaussian
mode. Increase to 60% if the mode looks more like ‘01*’ with a strong central dip.

Description of Part Number: FLDF-xxxx-D-T-F-dF-2h-yy

FLDF: single-element focusing lens with dual-focus
xxxx: laser wavelength, 10.6um.
D: lens diameter, mm (here is 28mm=1.1”, 38.1mm=1.5” & 50.8mm=2”, respectively)
T: lens edge thickness, mm
F: focal length, mm
dF: difference in focal length, units of 0.1mm
2h: diameter 2h, in units of 0.1mm
yy: others
Example: FLDF-10.6-D28-T4.2-F095-dF100-2h060 has a diameter of 28mm (1.1”), an edge thickness
of 4.2mm, a focal length of 95mm (3.75"), a difference of focal length of 10mm, and 2h = 6.0mm.

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 29
 Sintec Optronics Technology Pte Ltd

1. FLDF-10.6-D28-T4.2 series dual-focus lenses

FLDF-10.6-D28-T4.2 series dual-focus lenses are 1.1" diameter. They are intended to be used as direct
replacements for conventional lenses in industrial laser systems with ‘full’ beam diameters up to about
19mm (0.75"). Useful for improved cutting of stainless steel and aluminium in systems with smaller
beam sizes, this series of lenses are also intended for use in die-board cutting systems. In laser cutting,
dual-focus lenses exhibit some or all of these advantages:-

* Reduced / eliminated cut dross

* Increased thickness of cut capability
* Increased cut speed
* Improved kerf quality
* Reduced assist-gas usage
* Improved process control (die-board processing)

This technical data sheet presents a range of standard products. Non-standard lenses can be designed
and fabricated to order.

Technical specifications
Material Lasergrade ZnSe
Diameter 28.0 +0/-0.1mm
Edge thickness 4.2 ±0.1mm
Centration Within 0.05mm ETV
Coatings AR/AR for 10.6μm (R<0.25% per surface)
Absorption <0.20% at 10.6μm
LIDT (cw) >2000W/mm
Accuracy of 2h ±0.5mm
Note: laser induced damage threshold (LIDT)

Standard parts
z There are 3 standard basic focal lengths: 95mm, 127mm, 190mm.
z Each FL has several options for the difference in FL, chosen from the values dF = 5mm, 7.5mm,
10mm, 12.5mm, 15mm.
z Each option is available in one of five values for 2h. Standard values for 2h are: 4.0mm, 5.0mm,
6.0mm, 7.0mm, 8.0mm.
z The tabulated value ‘%L’ is the percentage of beam power in the lower focus, for a TEM00 beam of
12.0mm (1/e2) diameter.

For 95mm focal length, part no. is FLDF-10.6-D28-T4.2-F095-dFyyy-2hzzz

For 127mm focal length, part no. is FLDF-10.6-D28-T4.2-F127-dFyyy-2hzzz
For 190mm focal length, part no. is FLDF-10.6-D28-T4.2-F190-dFyyy-2hzzz
Focal Difference dF (mm)
2h (mm) 5.0 7.5 10.0 12.5 15.0 %L
yyy-zzz yyy-zzz yyy-zzz yyy-zzz yyy-zzz
4.0 050-040 075-040 100-040 125-040 150-040 20%
5.0 050-050 075-050 100-050 125-050 150-050 29%
6.0 050-060 075-060 100-060 125-060 150-060 39%
7.0 050-075 075-070 100-070 125-070 150-070 49%
8.0 050-080 075-080 100-080 125-080 150-080 59%

2. FLDF-10.6-D38-T6.2 series dual-focus lenses

The FLDF-10.6-D38-T6.2 series of Dual-Focus lenses are intended to be used as direct replacements
for conventional lenses in many industrial laser systems and applications. Designed to assist in a range
of thick-section cutting jobs, the FLDF-10.6-D38-T6.2 lenses are intended to give some (or all!) of these
advantages:

* Increased thickness of cut capability

* Improved kerf quality
* Reduced assist-gas usage
* Improved process control (die-board processing)

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 30
 Sintec Optronics Technology Pte Ltd

This technical data sheet presents a range of standard products. Non-standard lenses can be designed
and fabricated to order.

Technical specifications
Material Lasergrade
ZnSe Diameter 38.1 +0/-0.1mm
Edge thickness 6.2 +/-0.1mm
Centration Within 0.05mm
ETV Coatings AR/AR for 10.6　m (R<0.25% per surface)
Absorption <0.24% at 10.6　m
LIDT (cw) >2000W/mm
Accuracy of 2h ±0.5mm

Standard parts
z There are 3 standard basic focal lengths: 127mm, 190mm, 254mm.
z Each FL has three options for the difference in FL, chosen from the values dF = 5mm, 10mm,
15mm,20mm.
z Each option is available in one of five values for 2h. Standard values for 2h are: 5.0mm,
7.0mm,10.0mm, 12.5mm, 15.0mm.
z The tabulated value ‘%L’ is the percentage of beam power in the lower focus, for a TEM beam of
00
2
16.0mm (1/e ) diameter.

For 127mm focal length, part no. is FLDF-10.6-D38-T6.2-F127-dFyyy-2hzzz

For 190mm focal length, part no. is FLDF-10.6-D38-T6.2-F190-dFyyy-2hzzz
For 254mm focal length, part no. is FLDF-10.6-D38-T6.2-F254-dFyyy-2hzzz
Focal Difference dF (mm)
2h (mm) 5.0(1) 10.0 15.0 20.0(2) %L
yyy-zzz yyy-zzz yyy-zzz yyy-zzz
5.0 050-050 100-050 150-050 200-050 18%
7.0 050-070 100-070 150-070 200-070 32%
10.0 050-100 100-100 150-100 200-100 54%
12.5 050-125 100-125 150-125 200-125 70%
15.0 050-150 100-150 150-150 200-150 85%
Notes: (1) dF = 5.0 non-standard in FLDF-10.6-D38-T6.2-F254 series.
(2) dF = 20.0 is standard for FLDF-10.6-D38-T6.2-F254 series only.

3. FLDF-10.6-D38-T7.4 series dual-focus lenses

The FLDF-10.6-D38-T7.4 series of Dual-Focus lenses are intended to be used as direct replacements
for conventional lenses in Trumpf industrial laser systems and applications. Designed to assist in a
range of thick-section cutting jobs, the FLDF-10.6-D38-T7.4 lenses will give some (or all!) of these
advantages:
* Increased thickness of cut capability
* Improved kerf quality
* Reduced assist-gas usage
* Faster processing .. see note (1)
* Reduced under-surface dross .. see note (1)
Technical specifications
Material Lasergrade ZnSe
Diameter 38.1 +0/-0.1mm
Edge thickness 7.4 ±0.1mm
Centration Within 0.05mm ETV
Coatings AR/AR for 10.6μm (R<0.25% per surface)
Absorption <0.24% at 10.6μm
LIDT (cw) >2000W/mm
Accuracy of 2h ±0.5mm
Note (1): An independant laser user with a 3kW Trumpf laser reports 35% process speed increase and
85% dross reduction when cutting 10mm stainless steel.

Standard parts
z There are 3 standard basic focal lengths: 127mm, 190mm, 254mm.
z Each FL has three options for the difference in FL, chosen from the values dF = 5mm, 10mm,

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 31
 Sintec Optronics Technology Pte Ltd

15mm, 20mm. Each option is available in one of five values for 2h. Standard values for 2h are:
5.0mm, 7.0mm, 10.0mm, 12.5mm, 15.0mm.
z The tabulated value ‘%L’ is the percentage of beam power in the lower focus, for a TEM00 beam of
16.0mm (1/e2) diameter.

For 127mm focal length, part no. is FLDF-10.6-D38-T7.4-F127-dFyyy-2hzzz

For 190mm focal length, part no. is FLDF-10.6-D38-T7.4-F190-dFyyy-2hzzz
For 254mm focal length, part no. is FLDF-10.6-D38-T7.4-F254-dFyyy-2hzzz
Focal Difference dF (mm)
2h (mm) 5.0(2) 10.0 15.0 20.0(3) %L
yyy-zzz yyy-zzz yyy-zzz yyy-zzz
5.0 050-050 100-050 150-050 200-050 18%
7.0 050-070 100-070 150-070 200-070 32%
10.0 050-100 100-100 150-100 200-100 54%
12.5 050-125 100-125 150-125 200-125 70%
15.0 050-150 100-150 150-150 200-150 85%
Notes: (2) dF = 5.0 non-standard in FLDF-10.6-D38-T7.4-F254 series.
(3) dF = 20.0 is standard for FLDF-10.6-D38-T7.4-F254 series only.

4. FLDF-10.6-D38-T9 series dual-focus lenses

The FLDF-10.6-D38-T9 series of Dual-Focus lenses may be used as direct replacements for
conventional lenses in certain Bystronic industrial laser systems normally using 9mm ET lenses.
Designed to assist in a range of thick-section cutting jobs, the FLDF-10.6-D38-T9 lenses will give some
(or all!) of these advantages:
* Increased thickness of cut capability
* Improved kerf quality
* Reduced assist-gas usage(1)
* Faster processing
* Reduced under-surface dross
* Improved initial cut penetration

Technical specifications
Material Lasergrade ZnSe
Diameter 38.1 +0/-0.1mm
Edge thickness 9.0 ±0.1mm
Centration Within 0.05mm ETV
Coatings AR/AR for 10.6μm (R<0.25% per surface)
Absorption <0.25% at 10.6μm
LIDT (cw) >2000W/mm
Accuracy of 2h ±0.5mm
Note (1) Using dual-focus lenses, the ‘main’ beam is focused near the top surface of the workpiece. As
a consequence, the nozzle tip aperture can usually be smaller.

Standard parts
z There are 3 standard basic focal lengths: 127mm, 190mm, 254mm.
z Each FL has three options for the difference in FL, chosen from the values dF = 5mm, 10mm,
15mm, 20mm. Each option is available in one of five values for 2h. Standard values for 2h are:
5.0mm, 7.0mm, 10.0mm, 12.5mm, 15.0mm.
z The tabulated value ‘%L’ is the percentage of beam power in the lower focus, for a TEM00 beam of
16.0mm (1/e2) diameter.

For 127mm focal length, part no. is FLDF-10.6-D38-T9-F127-dFyyy-2hzzz

For 190mm focal length, part no. is FLDF-10.6-D38-T9-F190-yyy-zzz
For 254mm focal length, part no. is FLDF-10.6-D38-T9-F254-dFyyy-2hzzz
Focal Difference dF (mm)
2h (mm) 5.0(2) 10.0 15.0 20.0(3) %L
yyy-zzz yyy-zzz yyy-zzz yyy-zzz
5.0 050-050 100-050 150-050 200-050 18%
7.0 050-070 100-070 150-070 200-070 32%
10.0 050-100 100-100 150-100 200-100 54%
12.5 050-125 100-125 150-125 200-125 70%
15.0 050-150 100-150 150-150 200-150 83%

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 32
 Sintec Optronics Technology Pte Ltd

Notes: (2) dF = 5.0 non-standard in FLDF-10.6-D38-T9-F254 series.

(3) dF = 20.0 is standard for FLDF-10.6-D38-T9-F254 series only.

5. FLDF-10.6-D50.8-T9.6 series dual-focus lenses

The FLDF-10.6-D50.8-T9.6 series of dual-focus lenses are intended to be used as direct replacements
for 2.0" diameter, conventional high-gas- pressure lenses in some (larger) industrial laser systems.
Designed to assist in a range of thick-section cutting jobs, the FLDF-10.6-D50.8-T9.6 lenses will give
some (or all!) of these advantages:
* Increased thickness of cut capability
* Improved kerf quality
* Reduced assist-gas usage
* Increased cutting speed
* Reduced lower-surface dross

This technical data sheet presents a range of standard products. Non-standard lenses can be designed
and fabricated to order.

Technical specifications
Material Lasergrade ZnSe
Diameter 50.8 +0/-0.1mm
Edge thickness 9.6 ±0.1mm
Centration Within 0.05mm ETV
Coatings AR/AR for 10.6μm (R<0.25% per surface)
Absorption <0.26% at 10.6μm
LIDT (cw) >2000W/mm
Accuracy of 2h ±0.5mm

Standard parts
z There are 3 standard basic focal lengths: 190.5mm, 254.0mm, and 317.5mm. (7.5", 10.0" and
12.5", respectively).
z Each FL has three options for the difference in FL, chosen from the values dF = 10mm,15mm,
20mm, 25mm. Each option is available in one of five values for 2h. Standard values for 2h are:
10.0mm, 12.5mm, 15.0mm, 19.0mm, 22.5mm.
z The tabulated value ‘%L’ is the percentage of beam power in the lower focus, for a TEM00 beam of
25.0mm (1/e2) diameter.

For 190mm focal length, part no. is FLDF-10.6-D50.8-T9.6-F190-dFyyy-2hzzz

For 254mm focal length, part no. is FLDF-10.6-D50.8-T9.6-F254-dFyyy-2hzzz
For 317mm focal length, EFL part no. is FLDF-10.6-D50.8-T9.6-F317-dFyyy-2hzzz
Focal Difference dF (mm)
2h (mm) 10.0(1) 15.0 20.0 25.0(2) %L
yyy-zzz yyy-zzz yyy-zzz yyy-zzz
10.00 100-100 150-100 200-100 250-100 27%
12.50 100-125 150-125 200-125 250-125 39%
15.00 100-150 150-150 200-150 250-150 51%
19.00 100-190 150-190 200-190 250-190 68%
22.50 100-225 150-225 200-225 250-225 80%
Notes: (1) dF = 10.0 is non-standard in FLDF-10.6-D50.8-T9.6-F317 series.
(2) dF = 25.0 is standard for FLDF-10.6-D50.8-T9.6-F254 and FLDF-10.6-D50.8-T9.6-F317 lenses only.

If you are using a focusing in your laser cutting machine and want to convert it into dual-
focus lens, please tell the following parameters so that we can recommend suitable lens for
your applications:

z Laser wavelength
z Laser average power
z Laser beam diameter on the lens
z Laser beam quality (beam mode TEM00, TEM01, multi mode or M2)

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 33
 Sintec Optronics Technology Pte Ltd

z Parameters of current lens such as diameter, focal length, plano-convex or meniscus shape,
edge thickness
z What materials to be cut? Mild steel or/and stainless steel or other materials?
z What is the thickness of the materials?
z What assist gas is used in cutting? Nitrogen, oxygen, compressed air?

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 34
 Sintec Optronics Technology Pte Ltd

Mirror Mount
Model: MM-20
2D adjustable
Suitable for the mirrors with diameter 20mm

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 35
 Sintec Optronics Technology Pte Ltd

Beam Expander Mount

Model: BEM-22x0.75
4D adjustable
Suitable for the beam expander with a screw of M22x0.75mm

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 36
 Sintec Optronics Technology Pte Ltd

How to find the coating on the surface of the mirrors

1. Watch the surface at a angle (about45 degree) and you can see the color film on the mirror.
2. Sometime there is no coating near the edge and thus you can easily find the costing surface.

General rules about cleaning lenses/mirrors

1. Always wear finger cots when handling any lens or mirror to keep finger oils off of the optic.
2. Always handle optics by the edge of the optic. Never touch the coated surfaces.
3. Never rub an optical surface, as this can mar or scratch the coated surface.
4. Avoid using Q-tips or cotton balls to clean an optical surface.
5. Use a high-grade acetone to clean your optic, which should be dispensed by an eyedropper on to
lens cleaning tissue.
6. Never put any foreign objects back into the acetone dispenser to avoid contamination of the
acetone in the dispenser.

How to clean an optic:

Pull out your mirror/lens from its holder and lay it on a clean work area, or into a holder supplied by the
manufacturer. You will need a lens cleaning tissue containing low ash content and no chemical
additives. Also, you will need a small dispense bottle which has an eyedropper to apply the acetone.

1. If you do not have an optic holder, lay your optic onto a clean piece of lens tissue.
2. Remember that when lens tissue is dry it is abrasive and can scratch your optical surface.
3. Place a new piece of lens tissue over the optic, completely covering the optic.
4. Fill your eyedropper with 6-8 drops of acetone. You do not want to apply too much.
5. Drip acetone on to the center of the optic until it is saturated to the outside diameter of the optic.
6. Pull the lens tissue slowly across the optic. You will know if you are going too fast if you see residue
left behind. At the correct speed, the acetone will evaporate as you drag the tissue across the lens.
(If residue remains, you moved to quickly).
7. Repeat this process until you see a clean optical surface, with no marks or smudges. Always use a
new piece of lens tissue each time to keep contaminants off of the optic you are cleaning.
8. If after repeated cleaning of the optical surface you still see any spots, pits, or scratches, determine
whether or not to replace the optic with a new optic.
9. Replace your optics as soon as possible to keep any airborne particles from getting on the optic

http://www.SintecOptronics.com http://www.Sintecoptronics.com.sg 37