A Taste of Tubes - The Connoisseur's Cookbook - 1997, 67p

$5.
00
A TASTE OF
YOUR COMPLETE GUIDE TO
THE SENSORY DELIGHTS OF
TUBES
VACUUM TUBE AUDIO
TECHNOLOGY
Written for tube lovers of all persuasions and levels of expertise.

Presented for your enjoyment by:
YOUR COMPLETE
GUIDE TO THE
SENSORY DELIGHTS OF
VACUUM TUBE AUDIO
A TASTE OF
TECHNOLOGY
TUBES
T H E C O N N O I S S E U R ’ S C O O K B O O K
Written for tube lovers of all persuasions and levels of expertise.

Presented for your enjoyment by SONIC FRONTIERS, INC.
MANUFACTURER’S
OF THE
&
T UBE ELECTRONIC PRODUCT LINES.
COPYRIGHT AUGUST 1997

A TASTE OF TUBES: THE CONNOISSEUR’S COOKBOOK
The Menu
USING YOUR COOKBOOK Page iv
APPETIZERSPage 2
Tube History I: A Foretaste of Tubes Page 5

Edison Discovers the Genie in the Lamp Page 5
Fleming’s Electronic Aerial Page 6
De Forest Conjures a Triode Page 6
Tubes on a Roll Page 8
Tube History II: Amplifiers Du Jour Page 9

Cocking Cooks Up Quality Page 9
Williamson Stirs the Pot Page 9
The Pentode’s Revenge Page 10
Quad’s Potent Pentode Recipe Page 10
McIntosh’s Pentode Pièce de Resistance Page 11
Hafler and Keroes Go Ultra Page 12
Cooking the Signal: Tubes or Transistors? Page 14

Cleaning the Kitchen Page 15
MEAT & POTATOES Page 16
“Let Them Eat Glass” (The Inner Workings of the Vacuum Tube) Page 19
Cordon Bleu 101: Thermionic Emission Page 20
Tubes for All Tastes: Spicing the Circuits Page 22

i. Diodes Page 22
ii. Triodes Page 22
Cordon Bleu 102: Cooking with Triodes Page 24
iii. Tetrodes Page 25
iv. Pentodes Page 25
v. Beam Power Tubes Page 26
vi. Other -odes Page 27
vii. Sectional Tubes (Electronic Allspice) Page 27
Cooking with Tubes Page 28

i. Rectifiers Page 28
Cordon Bleu 103: Why Diodes are Directional Page 29
ii. Regulators Page 29
ii
Cordon Bleu 104: Advanced Regulation Page 30
iii. Amplifiers Page 31
Cordon Bleu 105: Ohm’s Law Distilled Page 32
Cordon Bleu 106: Advanced Amplification Page 33
Amplifier Flavors Page 34
Single-ended Page 34
Push-pull Page 34
Parallel Page 35
Ultra-Linear Page 35
iv. Preamps Page 36
v. Impedance Buffers Page 36
Tube Cuisine In Three Easy Classes Page 37

i. Class A Page 37
ii. Class B Page 38
iii. Class AB Page 38
Nourishing Your Playback System Page 40

Sonic Secrets Page 40
The Bitter Taste of Solid State? Page 40
The Inaccurate Measuring Spoon Page 41
They’re Warm! They’re Tasty! And They’re Tubes! Page 41
JUST DESSERTS Page 42
Feed ‘em, Clean ‘em, But Don’t Step On Their Toes! Page 43
Tasting Adventures: Trying New Tubes Page 45
Cooking at the Right Temperature: Biasing Page 48
Keep ‘em Fresh! Page 49
Onion Ice Cream: Some Final Thoughts
on the Transistor Page 50
Clearing the Table Page 51
Tube Futures Page 53
FOOD FOR THOUGHT Page 54
Bibliography Page 55
BITS & BYTES Page 58
How to Reach Us Page 59

Special Thanks Page 59
iii
USING YOUR
COOKBOOK
iv
Welcome to A Taste of Tubes. We’ve enjoyed writing it and
sincerely hope you’ll enjoy reading it. We think this little
book will increase your knowledge of — and appreciation
for — the efforts that tube lovers all over the world lavish on
their audio systems.
A Taste of Tubes is your guide to the ever-finer subtleties in

our auditory lives. You’ll find the recipes here easy to follow.
We’ll take you step by step through the basics and show you
the often hidden secrets that transform musical indifference
into musical rapture.
There is food here for everyone — from nouvelle gourmand

to advanced gourmet — so feel free to pick and choose.
You’ll find some sections on simple electronic theory, others
that will clarify more esoteric distinctions, and even enjoy-
able bits of tube history so you’ll really appreciate the rich
tradition you’ve chosen to explore.
If you should feel hesitant to dive into some of the thicker

batter, don’t worry. You can easily skim the advanced
“Cordon Bleu” sections on your first pass through the cook-
book (just as the Cordon Bleu is the premiere French cook-
ing school, these sections aren’t for those without a little
preparation). But don’t worry. After reading a few chapters
of A Taste of Tubes, you’ll be ready for those challenges, too!
Our advice is simple – skim through A Taste of Tubes at your

own pace. Then savor it slowly for maximum enjoyment.
1
APPETIZERS
2
Known by many names — vacuum tube, electron tube, valve
— the “tube” played an immensely significant role in the
development of our current audio
technology. Tubes, in all their vari-
ety and complexity, were the essen-
tial building blocks of electronic
circuits from the 1920s into the
1970s (Fig. 1).
Since then, however, the transistor

has largely supplanted the vacuum
tube. That’s understandable, at
least in part, as the transistor is far
smaller and less costly to manufac-
ture and incorporate in today’s
increasingly complex audio com-
ponents.
But a sizeable faction within

the audio industry continues to
Fig. 1. Raw materials in tube manufacture (circa 1930).
embrace the vacuum tube as a
device that results in more musically satisfying sound. In
fact, the past 15 years have seen a remarkable renaissance in
high quality tube electronics.
Why? Transistors didn’t suddenly rot overnight to become

foul tasting, did they? Probably not. Maybe our aural palates
just developed a craving for something more satisfying,
more sophisticated, more substantial?
To answer these questions, let’s look at the beginnings of the

Tube Era. We suggest that you don’t view this as just a dried-
out list of names and dates, but rather, as a savory foretaste
of the banquet ahead.
3
The Family Tree of Thermionic Tubes.
4
Tube History I
A Foretaste of Tubes
Edison Discovers the Genie in the Lamp

You may be surprised to learn that inventors (England’s Sir William
Watson among others) produced the first crude tube-like devices in
the mid-1700s. These early efforts were glass envelopes containing
both a cathode (emitter) and an anode (collector), but with only a
portion of the air pumped out. Given that sophisticated vacuum
pumps were not available until about 1912, at this time, the flow of
electricity through a tube was believed to be caused by ionization or
gas discharge. Nonetheless, these early tubes facilitated the discovery
of cathode rays (1858), and X-rays (1895).
It wasn’t until 1880, however, that the idea of a pure electron dis-
charge began to take root. The mystery began to unfold after Edison’s
discovery of a strange occurrence within his light bulbs. He noted that
a dark spot appeared on the inside glass wall of his bulbs when a car-
bon filament was used, and correctly surmised that electrical particles
drifted through the bulb and landed on the
glass wall.
This led him to insert into the bulb a

metal plate biased with a positive poten-
tial relative to the filament (Fig. 2). The
effect of the positive plate was to divert
the particles away from the glass wall.
Edison couldn’t explain why this
occurred, but he found a practical use
for it anyway: he patented the device as
an ammeter for measuring current flow.
Fig. 2.
Replica of Edison's experimental
lamp.
5
Fleming’s Electronic Aerial

Because Edison didn’t see the far-reaching implications of his device,
it was left to others —notably the British scientist John Ambrose
Fleming — to develop further applications for the “Edison effect”.
Fleming’s experiments led him in
1904 to develop a vacuum tube
diode capable of detecting wireless
radio signals. Fleming surmised
that, by connecting an aerial to
the positive plate, he might there-
by modulate the flow of current
through the tube by means of
wireless signals. This was the
first practical example of a
radio receiving tube (Fig. 3).
Fig. 3.
Production model of the Fleming detector valve.
De Forest Conjures a
Triode
In 1907, American inventor Lee De Forest,
attempting to improve upon the Fleming
diode, patented his famous Audion; a three-
electrode tube containing a third element
known as a grid. The following year, De
Forest improved the grid and moved it more
directly into the path between cathode and
anode. This innovation is widely considered
to be one of the most valuable in the patent
literature (Fig. 4).
Fig. 4.
Front page of De Forest patent #841,387;
Jan. 15, 1907.
6
Like his rival Marconi, De Forest intended his new device to play a
critical role in replacing the telegraph cable with wireless transmis-
sions. The idea of instantly communicating across the continents
fired De Forest’s imagination like nothing else: “I early resolved come
hell or high water, to achieve an envied position in the well-nigh vir-
gin field by inventing outstanding wireless transmitting and receiving
devices,” said De Forest. “I foresaw that wireless telephony would
ultimately supplement, if not supplant, the telegraph; that the human
voice, and possibly music, would replace the time-honored dots and
dashes of the Morse code.” These were prophetic words indeed!
A few years later, De Forest began to experiment with his three-element

tube as an amplifier. Although De Forest had some difficulty in getting
his device to function as he thought it should, he was none-the-less
able to build a working three-tube amplifier (gain = 42dB [more on
this later]) that, in 1912, worked sufficiently well to attract behemoth
AT&T’s interest in the device as a telephone repeater amplifier. In 1913,
De Forest produced a nifty looking four-tube amplifier (Fig. 5).
Fig. 5.
Lee De Forest
contemplating his four-stage amplifier,
developed in 1913.
7
Tubes on a Roll
Additional tube developments occurred at a rapid pace as more and
more air — and with it impurities that restricted performance,
longevity, or both — was removed from successive tube designs. Large
commercial interests, recognizing the tube’s vast potential, soon
added their considerable capabilities. Harold Arnold at Western
Electric (by then an AT&T subsidiary) and Irving Langmuir at General
Electric headed the teams that would soon make tubes viable com-
mercial products. By 1915, Western Electric had developed a tube
with a 4,000 hour lifespan — the Type L, later known as the 101B. It
wasn’t long before the race to place wireless reception in the home
began in earnest.
By 1920, the Corning Glass Works was producing 25,000 glass bulbs
per day. Uses ranged from receiving and transmitting to rectifying and
amplifying. In short, everything needed to bring radio programming
into the home. Radio broadcasters soon brought music, news, and
sporting events into the homes of millions.
Throughout the 20s, home radio consoles were all the rage. Not sur-
prisingly, companies such as Thordarson soon began producing pow-
erful replacement amplifiers for these sets. By the 1930s, radio man-
ufacturers began producing elaborate multi-tube amplifier designs —
some with as many as eight triodes in one product. High quality
radios, such as Zenith’s “Stratosphere” and E.H. Scott’s
“Philharmonic” soon followed.
8
Tube History II
Amplifiers Du Jour
Cocking Cooks up Quality
In 1934, W. T. Cocking’s seminal article on “quality amplification”
appeared in the British DIY publication, Wireless World. In it, Cocking
suggested that 5% distortion was too high for quality amplification.
He went on to state that “the aim [of playback] being to reproduce in
the listener’s own home exactly what he would hear if he were in the
studio.”
This statement marks the conceptual origin of the era of high fidelity,
insofar as we are able to trace it. Cocking is recognized as the
harbinger of high fidelity not only because he was influential and
authoritative, but because his amplifier was to evolve, by deliberate
steps, into the famous Williamson amplifier.
After explaining his approach, Cocking compared triodes to pentodes

and found triodes preferable for their ability to damp a moving-coil
loudspeaker at resonance. He next compared push-pull to single-
ended operation and concluded that the latter produced objection-
able 2nd harmonic distortion.
Cocking’s amplifier soon became known as “The Wireless World

Push-Pull Quality Amplifier”. This seed-pod or germinal amplifier
was destined to become the touchstone of tube design for nearly
twenty years.
Williamson Stirs the Pot

In April, 1947, D. T. N. Williamson’s article “Design for a High
Quality Amplifier” appeared in Wireless World. Williamson echoed
Cocking’s words when he summed up his analysis of the require-
ments for high quality amplification: “It appears then that the design
of an amplifier for sound reproduction to give the highest possible
fidelity should centre round a push-pull triode output stage and
should incorporate negative feedback.”
9
Thus, the evolution of Cocking’s “Wireless World Push-Pull Quality

Amplifier,” (as begun in 1934), ultimately culminated in the famous
Williamson amplifier of 1947. The distinguishing feature of each
incarnation of this amplifier was the use of triode tubes (actually,
KT66’s wired for triode operation) in push-pull configuration. In
spite of their reduced power output, triodes were preferred over
pentodes because their distortion products were found to be less
objectionable. This meant that, to obtain a given power output, more
money had to be spent. Thus the identification of high fidelity with
higher cost began to take root in the public mind.
In 1946, Avery Fisher introduced the first commercial high fidelity

system. It included a 50-watt triode amplifier, Jensen co-axial speak-
ers, AM/FM tuner, preamp and phonograph. The $1,200 price,
however, put this model out of the reach of most music lovers.
Other companies like Altec-Lansing, Brook, Bogen, Bell, and
RadioCraftsmen also joined in the fray. T o s ave money, audio
enthusiasts could buy hi-fi components in kit form from companies
such as Heathkit, Eico, and, later, Dynaco. The kit-building craze was
fueled by the large numbers of post-WWII military-trained
electronics technicians.
The Pentode’s Revenge

By 1949, Williamson’s triode amplifier had become the prototype for
high quality amplifiers the world over. In the face of this enormous
interest, there arose a new generation of pentode amplifiers to chal-
lenge the long-standing triode tradition. The pentode movement —
consigned to public address systems early on by engineers and audio-
philes alike — was reinvigorated when new techniques were discov-
ered that caused pentodes to sound/perform more like triodes.
Quad’s Potent Pentode Recipe

Three companies in particular stand out for their achieve-
ments in pentode amplifier design. In 1945, Peter Walker of
Quad found a way to dramatically reduce the high-order pen-
tode distortion products. Taking a clue from Blumlein, Walker
10
found a way to turn the high pentode gain into local feedback. To
obtain this feedback, Walker incorporated a tertiary cathode winding
within his output transformer (Fig. 6).
Fig. 6.
Basic circuit for the
Quad output stage.
This technique produced local feedback in accordance with the AC

impedance of the cathode winding. This more sophisticated form of
feedback provided a greater benefit than loop feedback alone, since
there was only one high-frequency pole to create phase shift. Unlike
loop feedback, the cathode feedback remained effective at the fre-
quency extremes, thereby reducing the high-order distortion products
associated with pentodes at no expense to power output!
McIntosh’s Pentode Pie`ce de Resistance

In 1949, Frank McIntosh and Gordon Gow took Walker’s technique
a couple of steps further in their 50W-1 amplifier. First, they
increased the number of turns in the cathode winding (Fig. 7) to
obtain correspondingly more local feedback.
11
Fig. 7.
Basic circuit of the McIntosh
unity-coupled output stage.
Second, the plate and cathode coils were wound adjacent (bifilar) to
one another to create a “unity coupling” between the two windings.
This reduced transformer leakage reactance by a factor of 3-to-1,
thereby extending transformer bandwidth and reducing phase shift.
The reduced phase shift translated into more effective loop feedback
at the frequency extremes, enabling McIntosh to claim the lowest dis-
tortion — across the widest spectrum — of any known power amp.
The editors of Audio Engineering hailed the McIntosh as “the first

major change in years in amplifier coupling circuit principles.” No
mention, however, was made of the Quad amp.
Hafler and Keroes Go Ultra

In 1951, David Hafler and Herbert Keroes approached the pentode
from a different angle. They returned a portion of the plate volt-
age to the screen-grid (Fig. 8). This local feedback loop became
known as the “ultra-linear” connection. It soon formed the basis
of the Acro Ultra-Linear amplifier. Keroes, a transformer expert,
knew that the screen-grid was a non-linear input terminal where
feedback is concerned. Nonetheless, he found that the tapping
point could be adjusted to enable linear feedback action. This nar-
row window of operation was claimed to provide “ultra linearity.”
12
Fig. 8.
The basic ultra-linear connection is a tap
connecting the screen grid to the output
transformer primary winding (Hafler and
Keroes used this connection, originally
attributed to Blumlein, in a push-pull
amplifier).
In their own words: “We have achieved a new tube type without
designing a new tube. This tube is neither triode nor tetrode, but its
improved linearity over either of those types justifies the designation
‘ultra-linear’.” In reality, this statement applies as much to the Quad
and McIntosh amps as it does to the Ultra-Linear amp.
Nonetheless, because the Quad amp was little known in the US, the
ultra-linear technique became widely adopted. During the Golden
Era alone, more than twenty different manufacturers adopted the
technique including Marantz, Harmon-Kardon, Fisher, Scott, Eico,
and Dynaco. Indeed, the very name, “Ultra-Linear”, was to become
generic; in that it ultimately came to refer to the technique itself,
rather than to the amplifier that inspired the name.
13
Cooking the Signal:

Tubes or Transistors?
It wasn’t until the late 1950s/early 1960s that transistors — solid state semicon-
ductors named for the combination of “transfer” and “resistor” — began to enter
the consumer electronic scene.
Purported to be more reliable than tubes, transistors certainly didn’t produce as

much heat (to be fair, most early transistor designs operated in what we call “Class
B” mode; you’ll see more about this in later sections of this book). In addition,
transistors were thought to be more physically robust than tubes — after all, tubes
did have glass envelopes, no?
Transistors certainly did allow manufacturers to make smaller, less expensive com-
ponents. Moreover, the market responded very positively to reduced costs and
promised performance benefits.
The reality, as it turned out, was somewhat different than expected. Early germani-
um-based transistors were actually very fragile outside the kind environments of the
research laboratory. When one transistor in a circuit failed, for example, it some-
times caused a catastrophic collapse of all downstream components that could rel-
egate an entire piece of equipment to the garbage heap.
High-powered output transistors in particular were extremely finicky and would

instantly self-destruct if accidentally shorted. However, the cost benefits of transis-
tor designs proved irresistible to manufacturers and, one by one, most gradually
shifted to solid state circuitry. Of course, reliability steadily improved.
A few die-hard companies, however, bucked

the transistor trend. These “high-end”
tube electronics manufacturers
stuck with tube designs because
they felt that transistors did-
n’t offer equivalent musical
satisfaction as compared to
tube-based electronics.
14
BEFORE WE MOVE ON
Audiophiles in the 40s and 50s had little choice but to
build their own high fidelity equipment. Not much
was available commercially, nor was it generally
affordable. A variety of amplifier designs were popu-
larized in the electronic hobby magazines of the day:
such as Radio and Television News, Radio Electronics,
and Audio Engineering (now known simply as
Audio). Parts such as tubes, resistors, and capacitors
were purchased from local electronic supply houses
(or by mail order) and often assembled at the kitchen
table in the evening.
Other amplifier circuits, including the soon-to-be-

famous Williamson, were published in Wireless
World. Additional circuits, published by tube manu-
facturers such as RCA and Mullard, also became pop-
ular during this era. The Williamson, however, con-
tinued to dominate the field. American companies
seized the opportunity and started producing kits so
home enthusiasts could more easily construct the
Williamson. Individuals such as David Hafler and
Herbert Keroes increased the power output of the
Williamson by offering ultra-linear transformers
under brand names such as Acrosound and Dynaco.
Other transformer manufacturers offered their own
quality versions – UTC with their “LS”(Linear
Standard) series and Altec Lansing’s “Peerless”
designs.
15
MEAT & POTATOES
16
Before we begin a more in-depth discussion of how tubes ten-
derize your music, let’s start with a somewhat simplistic analogy:
a tube is like a heart, controlling the flow of blood in a body, or
in this case, controlling the flow of electrons in a circuit (that’s
one of the reasons the British still call them “valves”).
As we mentioned before, tubes were necessary for all types

of electronics, not the least of which being radio and televi-
sion. In fact, early computers, for example — such as the
office-building-sized ENIAC and UNIVAC — depended on
tubes for their operation.
However, we should begin our review of vacuum tube tech-

nology by starting with the devices anatomy.
Fig. 9.
The internal details of a vintage RCA
multi-grid tube.
17
ANATOMY OF A TUBE
18
“Let Them Eat Glass”
The outer shell of an audio tube is constructed of glass. Inside the
shell, electrically biased grids and plates control the flow of electrons
through the tube. Thin wires from the tube elements pass through
the glass envelope and connect to pins on the tube’s base (Fig. 9).
These pins mate with sockets that connect the tube’s innards to the
external circuit.
The “vacuum tube” gets its name from the fact that almost all the air
must be removed from inside the glass envelope before the tube will
work properly. Getting the unwanted air out during manufacture is a
critical though imperfect process. Even the best modern tube manu-
facturing facilities can’t produce vacuums much below 100 millionths
of an atmosphere at sea level. This presents a significant challenge to
tube manufacturers because airborne contaminants drastically affect
a tube’s longevity.
All tubes have two basic electrodes: one

called a cathode and the other an anode
(more commonly called the plate
or collector plate). Briefly stat-
ed, an electric current
heats the cathode
which, in turn,
emits electrons
(Fig. 10).
...Cont. on pg. 20
Fig. 10.
The heated cathode is a profuse source of electron emission, especially when coated with the appro-
priate oxide, such as barium and/or strontium.
19
101: Thermionic Emmission

The cathode of most tubes is coated
with a material that emits a profusion
of electrons when heated (this is
known as “thermionic emission”).
Electric current from an outside
source passes through a nearby fila-
ment (a wire functionally identical to
the one in an incandescent light
bulb) to heat the cathode. The con-
struction (or architecture) of a given
tube design varies widely depending
Fig. 11. Cylindrical diode. on its intended use. For example,
some tubes have a directly-heated fil-
ament that doubles as the cathode, while others use a separate
heater element to indirectly heat the cathode. Some have plates that
are flat (as in Fig. 10) while other plates are cylindrical (Fig. 11).
Electrons are either directly attracted by the pos-
itively charged plate or indirectly guided toward
it by an intervening control element called a
grid. These additional elements are called grids
because their physical structure consists of a
frame of spaced parallel wires (Fig. 13).
Although the electrons’ exact path varies by tube
type, they generally migrate directly toward the
plate. The plate, in turn, pulls the electrons
toward it due to the natural physical attraction
between negative and positive charges.
Strictly speaking, the plate attracts electrons

Fig. 12. either directly or by neutralizing a portion of the
Potential gradient from plate to grid. The potential at the plate is
negative grid field (Fig. 12). But you’ll under-
strong enough to attract electrons even when the grid is at ground
potential (0V). This is why a negative bias is applied to the grid. The stand that better after reading the next section.
negative bias allows the grid to control electron flow, overriding the
field at the plate.
20
Fig. 13.
Cutaway view showing the three most commonly used grids.
Controlling the electron flow is crit-

ical, and specific tube designs han-
dle this task in different ways. For
example, a tube can increase a sig-
nal’s amplitude (amplification) by
incorporating additional control
elements within the tube envelope.
BEFORE WE MOVE ON
In summary, then, a vacuum tube (as used in a
preamplifier) amplifies small voltage inputs
from a source component like a phono cartridge,
a CD player, or a tuner to produce the higher
voltages necessary to drive a power amplifier,
which then drives the loudspeaker. Thus, tubes
help transform music signals into sound waves
so we can all enjoy music in our homes. Of
course, in this respect, tubes are functionally
identical to transistors. Tubes, however, are sig-
nificantly different in how they accomplish sig-
nal transfer. These differences are critical to the
enhanced musical enjoyment many people
attribute to tube designs. We’ll see more on this
21
Tubes for all Tastes:

Spicing the Circuits
Adding elements to the tube architecture changes the tube from diode
(2 elements) to triode (3 elements), to tetrode (4 elements), all the
way to pentode (5 elements).
i. Diodes
A diode is the vacuum tube’s simplest incarnation. This two-element
tube consists of an anode (plate) and a cathode. A diode conducts
current only when its plate is made positive relative to its cathode. If
the potential on the plate is reversed from positive to negative, the
free electrons in the space surrounding the cathode will be forced
back to the cathode and no plate current will flow. The effect is some-
what like that of a one way street in which the current can flow only
in one direction. If the plate potential is alternated from positive to
negative, plate current flows in one direction only thus changing the
alternating current (AC) to direct current (DC). The diode finds appli-
cations in tuners as a demodulator (detector). In amplifiers, a diode
is most often used as a power supply rectifier. Rectification is the first
step in converting AC to DC (you’ll see more on this shortly).
Common Tube Rectifiers: 5AR4, 5Y3GT, 6X4, 12X4, 5U4G, GZ37

(each contains 2 diode sections for full wave rectification).
ii. Triodes
Triodes are three-element tubes used primarily for amplification. A
triode is created by adding a grid element in between the cathode and
the plate (Fig. 14). This grid is called the “control grid” because its
effect upon current flow is more pronounced than that of the plate.
22
We can test the basic action of the grid by apply-
ing different bias potentials to it. For exam-
ple, when the grid is biased positive, plate
current increases (Fig. 15). When the grid
is biased at zero, only moderate current
flows. When the grid is biased negative,
plate current is minimized. The audio sig-
nal thus acts to vary the grid bias Eg and
thereby control plate current.
A triode’s most important function is amplifica-

tion, in which small voltage variations at the input
are transformed into much larger variations at the
output. The object is to exactly replicate the delicate
fluctuations of the input signal (you’ll see more
about this in the following sections).
Amplifying such small signals effectively requires
Fig. 14.
Cutaway depiction of a Western Electric
101-F triode (circa 1915).
Fig. 15.
When Eg > 0, current flow
increases (left); when Eg = 0,
current flow is nominal (mid-
dle); when Eg < 0, current
flow decreases.
that noise and interstage crosstalk be reduced to vanishingly low lev-

els. This is accomplished by astute circuit design on the one hand
and by low-impedance or elaborate power supply design on the
other.
Common power triodes: 45, 71, 2A3, 6B4G, 50.
“Not” so common power triodes: 211, 300B, 845, 811.
Common small-signal (dual) triodes: 12AU7, 12AT7, 12AX7, 6DJ8,

6922, 6CG7, 6SN7, 6SL7, 5687, 6072, 7025, 6AQ8, 6201, 5751, 5691,
5692, 12BH7.
23
102: Cooking with Triodes
One of the triode’s most important characteristics is that

small changes in grid voltage will have significantly greater
effect on current flow through the tube than if the same
voltages were applied directly to the plate itself. As an exam-
ple, a one volt increase at the grid might result in a ten volt
increase at the plate. Such a tube would have an amplifica-
tion factor of 10. In practice, triodes are made with ampli-
fication factors as high as 100.
Designers, however, aren’t limited to a particular tube’s

amplification factor. If you take two triodes, each with an
amplification factor of 100, and connect them in a cascade
(series) circuit, you’d achieve a total amplification factor of
10,000 (100 x 100 or 1002). Adding a third tube to the chain
gives you an amplification factor of 1,000,000 (1003). A
fourth tube would bring the amplification factor to
100,000,000 (1004) and so on.
That’s pretty impressive for such a simple device but remember

that we need these amplification factors because the signal lev-
els of source components (especially moving coil phono car-
tridges) are very small indeed — on the order of 200 mil-
lionths of a volt! (That’s 200 microvolts or 0.0002 volt.)
24
iii. Tetrodes
Tetrodes contain four elements. The fourth element is a second grid, usu-
ally called the screen grid, positioned between the control grid and the
plate (Fig. 16). The effect of the screen grid is to shield the input signal
from the high grid-to-plate capacitance of the triode. The tetrode’s low
input capacitance makes it ideal for wideband circuits (radio frequency
designs, for example).
Whereas the control grid is negatively

charged, the screen grid is positively charged.
The gaps on the screen grid are much larger
than those on the control grid; so that, even
though the screen grid is biased positive, it
allows most of the electrons to pass through
to the plate. In addition to its shielding
effect, the screen grid acts to assist the plate
in attracting electrons from the cathode.
Moreover, due to the increased positive volt-
age gradient introduced by the screen grid, it
also acts to accelerate electrons.
The accelerated electron flow to the plate

Fig. 16.
becomes quite turbulent, however, because
Cross-section of a tetrode tube showing primary and
secondary electron directions. now electrons develop sufficient speed to
bounce off the plate and return to the screen
grid where they are subsequently dissipated as useless heat. These “sec-
ondary electrons” reduce the tetrode’s overall efficiency. For this reason,
the tetrode was soon supplanted by the pentode, which was designed
specifically to address this problem.
iv. Pentodes
Pentodes add a third grid element. This element, referred to as a sup-
pressor grid, is positioned between the screen grid and the plate (Fig. 17).
The suppressor grid is biased with a very low negative potential to repel
secondary electrons back to the plate, thus increasing overall efficiency.
25
Pentodes can be converted to triode

operation simply by shorting the screen
grid to the plate. In fact, some pentodes
display outstanding audio characteristics
when operated in triode mode.
Common pentodes: 6CA7, EL34, 6BQ5,

EL84, 7189, 6K6, 6F6, 47, EF86, 12BY7.
v. Beam Power Tubes

Beam power tubes are the culmination of
audio power tube design. The beam tube,
like its sibling the tetrode, contains a cath-
ode, a control grid, a screen grid, and a
plate. However, the beam tube functions
as a pentode. This identity crisis arises
because the tube’s directed electron beams
create a virtual suppressor by setting up
potential gradients between screen grid
Fig. 17.
and plate. In addition, the two grids are Cross-section of a pentode tube showing a potential
aligned such that the gaps in the screen minimum at the negatively biased suppressor grid.
grid fall within the ‘electrical shadow’ of
the gaps in the control grid (Fig. 18).
This orientation, assisted by a

pair of beam forming ele-
ments, focuses the electron
stream into an array of com-
pact sheets. This further assists
the virtual suppressor to
reduce secondary electrons.
Thus, more electrons make
their way to the plate, and effi-
ciency is increased even
beyond that of a pentode.
Fig. 18.
Interior view of a beam power tube. The electron
stream flows out of the cathode in compact sheets.
26
Beam power benefits include high power output, high sensitivity, and
high efficiency. Compared to the pentode, it produces slightly more
power with less distortion.
Common beam power tubes: KT66, KT77, KT88, KT90, KT100, 6550,
5881, 807, 6V6, 6L6.
vi. Other -odes

Tubes with even more grids (hexodes, heptodes, and octodes) also
exist but are used mostly in RF (radio frequency) circuits — such as
radio and television tuners — for frequency conversion and mixing.
vii. Sectional Tubes (Electronic Allspice)

In addition to single-section tubes, many multi-section tubes also
exist. For example, dual diode tubes are sometimes used for rectifi-
cation. Small dual triodes frequently serve for low-level signal ampli-
fication.
Some tubes combine totally different architectures — a triode and

pentode, for example — within a single tube envelope. (The 7199
used in the Dynaco Stereo 70 amplifier is a classic example of this
hybrid approach.) The operating principles of each section are iden-
tical to the types described earlier (diode, pentode, etc.), but multi-
section tubes help conserve space and shorten signal paths.
27
BEFORE WE MOVE ON
Diodes, then, are rectifiers that convert alternating
current into direct current. They can also be used as
detectors in tuner circuits. Triodes, tetrodes, and
pentodes are amplifiers that increase the strength of
the electrical signal from your source components,
creating a signal capable of driving output devices
and loudspeakers.
Cooking with Tubes

i. Rectifiers
Rectifiers come in a variety of flavors: half-wave; full-wave; full-wave

bridge; bi-polar; and voltage-
multiplier. The full-wave rec-
tifier is the most common
type of rectifier for tube cir-
cuits (Fig. 19).
Rectifiers convert wall-sock-

et AC current into pulsating
DC current. This one-way
current can then be
smoothed out so that no
alternating components (AC
harmonics) appear on the
power supply rails, which
would otherwise inject hum
and noise into the audio cir-
Fig. 19. Full-wave tube rectifier circuit.
28
Fig. 20.
Due to the transformer connection, one
diode plate conducts on the positive half-
cycle and the other plate conducts on the
negative half-cycle of the AC input wave-
form. The output waveform then appears
as pulsating half-cycles. These half-cycles
can be smoothed out by including filter
elements after the rectifier.
103: Why Diodes are Directional

The plate, when connected to an AC source, receives a
charge that continually reverses between positive and nega-
tive. When negatively charged, the plate loses its attractive
power, so no current passes through the tube. Thus, all the
current pulses through a diode occur during the positive
half-cycle of the AC waveform. The positive pulses then line
up to create what is called “pulsating DC” (Fig. 20).
ii. Regulators
Once the AC wall-socket current is rectified, it can then be regulated.
Regulation implies that the power supply voltage is maintained at a
fixed voltage, regardless of AC line voltage fluctuations or load cur-
rent variations. The object is to allow only the audio signal voltage to
vary, and to suppress false signals from the power supply.
29
104: Advanced Regulation

A regulator functions as a comparator circuit. In its most
basic form, a power tube is utilized as a “pass device”. This
tube’s grid is connected to a fixed reference voltage such as
a zener diode or gas discharge tube. The output of the pass
device is then
connected to the
circuit (Fig. 21). A
voltage fluctua-
tion at the input
is thus reduced
by the amplifica-
tion factor of the
tube.
Fig. 21. Basic regulator circuit.
To increase the effectiveness of this arrangement, an error

amplifier tube is often connected in between the voltage ref-
erence and the power tube’s grid (Fig. 22). Now the fluctua-
tions are reduced by the gain of the error amplifier times the
gain of the power tube, greatly increasing the power supply
rejection and approaching a zero output impedance. In
practice, this output impedance will be somewhat greater
than zero and will rise with frequency.
Fig. 22. Regulator circuit

with error amplifier.
30
A complete power supply consists of a transformer; rectifier; filter;
regulator; and dividing network (Fig. 23).
More advanced power supplies use additional regulators to reduce

interstage and/or interchannel crosstalk.
Fig. 23.
Complete power supply showing the change upon the input waveform (AC) at various stages
within the circuit. The AC has effectively been reduced to steady current (DC) at the output.
iii. Amplifiers
Next, we come to the amplifier itself. This circuit is really no more
nor less important than the regulator in obtaining good sound, just
different in its requirements. Amplifier circuits come in a dazzling
variety of flavors. In order to better appreciate these flavors, we here
present a cook’s tour of the main ingredients. The first thing to know
about tubes (and about electricity in general) is that voltage stimu-
lates electron flow. Voltage is defined as the difference in electrical
potential across a conductor or across space — as in a vacuum tube
(See Cordon Bleu 105 on the following page).
31
105: Ohm’s Law Distilled

A resistor subtracts or drops voltage whenever current flows through it.
According to Ohm’s Law, the voltage varies directly as the current varies. The
defining statement of this law is:
E = I x R (where E = voltage, I = current, R = resistance)
This formula gives the voltage drop across any given fixed resistance for any
given current flow through the resistor. Thus, potentials can be established
as needed throughout the circuit merely by adjusting the resistor values. Once
established, these potentials fix the current flow through any given circuit
node. The object is to allow only the audio signal voltage
to vary the current flo w.
Amplification occurs by an adept combination of voltage

source (power supply or battery), series resistance (or reac-
tance), and active device (tube or transistor). Although the
basic rules apply to transistors as well as to tubes, for pre-
sent purposes we will use the triode. Note that the positive
potential provided by a high voltage source causes current
to flow through the triode as well as through any resistor
that is placed in series with it (Fig. 24).
Because the input or control grid is the closest electrode to

the cathode, a change in the electric field of the grid has a
bigger influence on current flow than does the plate field. Fig. 24.
The process of amplification requires an external
(Hence the name “control grid.”) The current flowing to
plate load resistor in addition to the tube itself. The
the plate will also flow through the external plate plate current flowing through this resistor produces a
resistor in order to complete the circuit from volt- voltage variation that is an amplified version of the
input waveform.
age source to ground return. Thus, a voltage varia-
tion occurs (equivalent to e = iR, where i = the
instantaneous plate current) through the plate resistor. The small
signal variation at the input then creates a large signal variation at
the output (amplification) (see also Figs. 12 and 15).
32
106: Advanced Amplification
Accurate amplification demands that the overall circuit exhibit two essential
characteristics. First, the power supply should exhibit zero internal imped-
ance and therefore zero voltage variation as the load current varies. Of course,
this is an ideal condition that is approached only by regulated power sup -
plies. Second, each tube must be biased for linear response within a critical-
ly specified range of operation.
A designer uses a “load-line” (i.e., a working path of operation drawn across

the graph of a given tube’s conductance characteristics) to obtain the operat-
ing point, Q (Fig. 25). The range i b shows the amount of plate current flow-
ing at any given instant. It can be seen that at Q the tube is flowing about half
its maximum current. When the input signal turns negative, less current
flows; when the signal turns positiv e, more current flows (up to i b max).
By this means, a complete cycle is reproduced, even though the electron cur-
rent is flowing in one direction only through the tube. This is what is meant
by “biasing the tube” or “setting the operating point”. The designer tries to
draw the load-line across the most linear portion of the plate characteristics.
Fig. 25.
The load-line shows the working characteristic of the tube, and allows the output waveform to be compared to the input
waveform via the dynamic transfer characteristic; which, in a perfectly linear tube, would be a straight line.
33
Amplifier Flavors
Single-Ended
A single-ended amplifier uses one

active device to produce both half-
cycles of the audio signal (Fig. 26).
The term “single-ended” implies that
the circuit is not balanced. Single-
ended tube designs are necessarily
operated in Class A mode and, con-
sequently, tend to be very inefficient.
Fig. 26. Single-ended amplifier circuit.
They have an advantage, however, in
that they tend to produce smaller
amounts of high-order harmonic distortion. This is because, in sin-
gle-ended amplifiers, there is no possibility of crossover distortion
(you’ll find more about this a little later).
While single-ended amplifiers are often touted as simpler - hence,

better - this may not always be true in practice. For example, to obtain
higher power outputs, multiple tubes must be paralleled in the out-
put stage. In addition, if feedback is to be
used, an additional gain stage must usu-
ally be added, just as in push-pull
designs.
Push-Pull
Push-pull amplifiers employ a pair of

tubes that operate alternately to repro-
duce the two halves of the audio signal
(Fig. 27). Push-pull amplifiers necessarily
employ a “phase splitter” to create a
Fig. 27.
phase-inverted clone of the input signal Push-pull amplifier circuit. Even-order distortion products such as i2
(for single-ended inputs). For balanced travel through the transformer in opposite directions. The resulting
inputs the phase inverter is not needed. magnetic fields, being of opposite polarity, then cancel.
34
The phase-inverter’s output drives the two sides of the push-pull out-
put stage so that each tube in the pair “hands-off” the signal to the
other to produce a complete waveform at
the output. This hand-off operation can
create crossover distortion if the amplifi-
er is not carefully designed.
A push-pull output stage may be operat-

ed in Class A, B, or AB. The class of oper-
ation determines the amount of overlap
between the half-cycles at the hand-off
(you’ll find more about this a little later).
Depending on their degree of balance,
push-pull amplifiers will cancel even-
order distortion products, leaving odd-
Fig. 28. harmonic residuals (Fig. 28). Since the second harmonic tends
The two tubes, T1 and T2, combine their
anti-phase outputs to produce a com-
to dominate the distortion spectrum, push-pull amplifiers
posite waveform at the main output. In tend to have much lower total harmonic distortion figures. If
so doing, even-order harmonic products not carefully designed, however, they can produce annoying
(especially 2nd harmonic) are drastical-
ly reduced.
high-order products due to crossover distortion (see also The
Bitter Taste of Solid State, pg. 40 and They’re Warm! They’re
Tasty!, pg. 41)
Parallel
This is not really a separate category at all: both single-ended and

push-pull topologies may use more than one tube (single-ended) or
one pair (push-pull) connected in parallel. This does not change
either mode’s basic operation.
Ultra-Linear
If you’ve already read the section Tube History II: Amplifiers Du Jour
(pgs. 9-13), you already know a lot about the Ultra-Linear approach.
If you haven’t yet read that section, maybe now would be a good time
to do so. To summarize, the ultra-linear output stage configuration is
a way of using a tetrode, pentode or beam power tube to achieve tri-
ode-like characteristics.
35
Fig. 29.
Schematic diagram of the original
Ultra-Linear amplifier of Hafler
and Keroes (one channel shown,
plus power supply).
while maintaining their high gain and efficiency. Simply put, the
ultra-linear connection was an attempt to combine the advantages of
both triodes & pentodes, with few drawbacks. Some of you who’ve
read this far may be wondering what a complete amplifier circuit
looks like. Fig. 29 shows the complete schematic diagram of the orig-
inal Ultra-Linear amplifier of Hafler and Keroes, circa 1951.
iv. Preamps
Preamps come in two basic flavors: phono and line. The phono pre-
amp is distinguished by its RIAA equalization filters, its high gain,
and its low noise. The line stage is distinguished primarily by its con-
trol features, such as volume control and switching functions. Most
line stages also provide gain.
v. Impedance Buffers
An impedance buffer, often known as a “cathode follower,” is essen-
tially a tube that uses up all of its available gain as feedback (Fig. 30).
36
This gives the cathode follower
a high input impedance, mak-
ing it easy to drive. It also gives
it a low output impedance,
making it ideal as an output
stage. That’s because, with a
low output impedance, the
tube is more immune to cable
capacitance and/or inductance,
which would otherwise cause
high-frequency roll-off.
Fig. 30.
A cathode follower circuit produces
local feedback due to the large value
cathode resistor.
Tube Cuisine in Three Easy Classes

There are three “classes” of amplifier operation commonly used for
audio applications: Class A, Class B, and Class AB. These operating
classes apply to all amplifiers, whether solid-state or tube.
i. Class A
Class A refers to a state of operation in which the operating point is
set to a level at least half that of the maximum output current of the
tube. In this mode of operation, the
tube conducts current over the entire
cycle of the input signal (Fig. 31). Thus,
there is no crossover or notch distor-
tion: the waveform is uninterrupted at
the zero-crossing between its positive
and negative half-cycles.
A Class A amplifier also has the lowest

output impedance of any operating
class. Its disadvantage is inefficiency. A
Fig. 31. Class A amplifier that develops even 50
The Class A output waveform, shown as ib ,
watts will be a large piece of equipment
is a continuous cycle.
37
indeed; use lots of electricity, and, because the output tubes produce half their
maximum current even at idle, produce a surprising amount of heat!
ii. Class B
More complex “push-pull” amplifiers drive two tubes alternately, and the neg-
ative cycle is allowed to cut-off. Class B refers to amplifiers having output stages
with no idle current at all. True Class B designs “turn on” an output device at
the exact instant it is needed to reproduce the positive or negative half of the
waveform (Fig. 32). This abrupt transition between “off” and “on,” while
tremendously efficient, pro-
duces substantial crossover dis -
tortion that makes these
designs generally unsuitable for
high fidelity applications.
iii. Class AB
In Class AB, the two alternating
current pulses overlap to some
Fig. 32.
extent during the hand-off (Fig. The Class B output waveform
33). Bear in mind that push- cuts off abruptly at the zero-
pull amps can also be operated crossing (baseline or timeline).
in Class A. This is rarely done, however, because there is no

penalty in allowing the negative cycle to cut-off, provided that there is suffi-
cient overlap between the half-cycles.
The term “Class AB” indicates

that the operating point is set
part-way between Class A and
Class B. Thus, Class AB designs
combine Class A’s linearity
with Class B’s efficiency, with
very few of the drawbacks of
either. The overlap between the
half-cycles largely eliminates
Fig. 33. crossover distortion (Fig. 34).
The Class AB output waveform is
permitted cut-off on the negative
cycles. There is some overlap,
however, between the push and
the pull waveforms.
38
Fig. 34.
Due to the lack of overlap, the two half-cycles
fail to conduct at the zero-crossing, producing
crossover distortion. This is due to curvature of
the plate characteristics near the bottom of the
load line (see Fig. 25).
Most high fidelity audio amplifiers operate in Class AB mode. A properly

designed Class AB amplifier will perform at levels comparable to Class A designs.
BEFORE WE MOVE ON
TO SUM UP: Class A amplifiers usually cost the most
and are the least efficient. They also have the poten-
tial to sound the best. True, they waste power but give
very clean reproduction. Class B amplifiers are used
where high efficiency is a primary requirement —
applications such as public address (PA) and similar
non-critical applications. Class AB amplifiers domi-
nate the audio market, and, with careful design, can
rival Class A amps in sound quality. They’re more effi-
cient (i.e., use less power), and are usually less expen-
sive, smaller, cooler, and lighter than their Class A
cousins.
39
Nourishing Your Playback System

Sonic Secrets
Compared to most solid-state (transistorized) audio equipment, tube cir-

cuits offer several advantages. A tube’s inherently simple operating principles
mesh perfectly with the minimalist circuitry most high-end designers favor.
A firmly entrenched high-end canon states that every component added

to the signal path imparts its sonic signature to the sound. That is why the
best designers take so much care in their passive parts selection. Whether
it be the choice of wire, connector, switch, resistor or capacitor, all will
have a significant effect on the final sonic outcome. From a purely musi-
cal standpoint, simple signal paths usually have the least detrimental effect
on the input signal. Once a low-voltage signal is retrieved and converted
by a source component, it can’t ever be improved. Unfortunately, howev-
er, it can be degraded. Complex signal paths often provide more ways to
affect and modify the signal. We call that process coloration — the audi-
ble resonance’s and signatures of the parts themselves — and it is some-
thing we need to minimize in any high fidelity system.
The Bitter Taste of Solid Stat e ?

Transistor circuits have a strong tendency to produce what we call high-
order distortion. These distortions are harsh sounding because they are
dissonant with the original signal. Most early transistor-based audio
equipment sounded harshly antiseptic due to the high crossover distor-
tion of early Class B designs. In addition, another artifact, eventually iden-
tified as “transient intermodulation distortion” (TIM), resulted from poor
implementation of negative feedback. Improperly applied feedback
affected the sound in a negative way, even while it measurably reduced
other, better known, forms of distortion.
It was around this tube-to-transistor transition that the term “listener

fatigue” was first used to describe the “makes-me-want-to-pull-my-hair-
out” reaction most listeners had to the edgy sound of early transistor prod-
ucts. In fairness, we must admit that solid-state designs have improved
greatly over the years, both in terms of sound quality and reliability.
40
The Inaccurate Measuring Spoon
The aural impact of the different harmonic profiles exhibited by solid
state and tube circuits points out some of the difficulties faced by
high-end designers even today as they balance what may measure bet-
ter against what may sound better. The two are not always synony-
mous, as conventional measurements do not always reflect instanta-
neous signal conditions found in music programs.
They’re Warm! They’re Tasty! And They’re Tu b e s !

On the other hand, tube designs, even though they tend to produce
more total distortion than their solid-state offspring, often produce a
more agreeable form of it. Technically described as low-order distor-
tion, the spurious second and third harmonics generated by tube
designs are far more consonant with the original signal and thus less
objectionable. In fact, tube circuits and people proved to be remark-
ably congruent as the human hearing mechanism tends to interpret
low-order distortion as a welcome warmth and mellowness that can
enhance our enjoyment of music.
BEFORE WE MOVE ON
In truth, we’re still learning why tubes and transistors
differ so remarkably in their audible characteristics.
But we do know that tube electronics’ relative simplic-
ity means a less convoluted signal path. The fewer
steps taken in that signal path, the less that can go
wrong with the music. So, according to many audio-
philes, there is just nothing more beneficial than vacu-
um tubes in your audio system!
41
JUST DESSERTS
42
Feed ‘em, Clean ‘em,
But Don’t Step on Their Toes!
(How to Care for Your Tubes)
Although some special purpose tubes (nuvistors and trans-
mitting tubes in particular) have metal envelopes, almost all
of the tubes we encounter in audio equipment are encased
in glass. And, as we all know, glass does break occasionally.
The good news, however, is that vacuum tubes are fairly
robust devices. They’re also self-contained and surprisingly
immune to the external environment. This means, for one
thing, that they can last almost indefinitely on the shelf.
Nonetheless, we don’t recommend that you test a tube’s

ruggedness by deliberately dropping one on a concrete
floor! If you do, you’ll probably spend a bit of time on your
knees apologizing to the Tube God as you sweep up tiny
pieces of glass (Fig. 35).
Fig. 35. Over-anxious tube jockey at work.
43
We do recommend that you read the following paragraphs for some

tips on handling and preserving your tubes so you can enjoy their
warm, soft glow and luscious music for many years.
Watch an experienced audio hobbyist change tubes in a valued com-

ponent and you might think you’re in a surgical operating room! See
those little white cotton gloves? There’s a reason for them: handling
tubes with your bare hands usually means that some of your body
oils and acids get transferred to the tube’s glass envelope. Over time,
the tube’s high surface temperatures promote chemical reactions
between these contaminants and the surface that can weaken the
glass and cause a structural failure. Guarding against this potential
problem is easy: use clean cotton gloves or simply wipe fingerprints
from your tubes after you handle them.
Properly handling the bottom of a tube is also very important.

Specifically, you need to exercise a little caution around the pins that
protrude from its base as they’re essential to the tube’s operation.
After all, they’re the only contact between the tube and the rest of the
circuitry in whatever component you’re using them.
When you’re changing tubes, make sure that these pins are clean.
Also check to make sure that the tube sockets are clean and free of any
debris that may have accidentally found its w ay into the pinholes.
Tubes can be inserted into their corresponding sockets in only one way.
Smaller tubes (miniature, bantam, etc...) generally have a circular array
of nine pins and a gap where a tenth pin would appear if it existed.
The corresponding tube socket has nine holes and a corresponding
gap. Larger, 8-pin (octal) tubes have a locating rib that can fit into the
socket in only one way. Once you’ve aligned the rib with the key-way
in the socket, proper pin matching is assured. There are also tubes with
4-, 5-, and 7-pin bases. But don’t worry — these tubes are also
designed so that you can’t accidentally insert them the wrong way.
When pulling out or replacing tubes, let common sense be your

guide. Don’t yank out old tubes — while grasping by the
44
base, a steady, even pull with a little (usually VERY little) side-to-side
rocking will get all but the most stubborn tube out of a socket. When
replacing it, make sure to align pins and socket holes before seating
the tube with a steady, even push. It’s also a good idea to clean the
pins occasionally with a small welder’s brush. After a gentle scrub,
you may wish to treat the pins with an electrical preservative.
Tasting Adventures: Trying New Tubes

There are a few simple guidelines to follow to insure the best possi-
ble sonic performance from your tube equipment.
Whenever possible, use identical tubes (the same tube type from the
same manufacturer) for corresponding stages of both left and right
channels of your equipment. For example, if you’re using Svetlana
6550Cs in one channel of a stereo power amplifier, it probably isn’t
a great idea to use a different brand in the other channel, or to use a
Yugo-EI KT90 if one of the Svetlana’s suddenly goes to Tube Heaven.
There are differences between brands — some subtle, some not —
that might upset left-right musical balances.
But don’t take this as a warning against experimenting. As we’ll short-

ly explain in more detail, trying different tubes is one of the real plea-
sures available to the “tube-aholic.” You may find a particular syner-
gy in using tubes from one manufacturer in a phono circuit while
another manufacturer’s product might provide just what you’re look-
ing (or listening) for in line stage applications. Just make sure to try
new tubes symmetrically between channels rather than in a haphaz-
ard manner.
Don’t feel obligated to stick with the same brand of tubes that origi-
nally came with your components, either. As we’ve already implied,
many audiophiles have an almost fervent devotion to one brand and
will use it religiously in their equipment regardless of what was orig-
inally supplied.
Some audiophiles, generally those with healthy budgets, are

fond of NOS (New Old Stock) tubes such as the Western
45
Electric 300B, Gold Lion KT-88, Mullard EL-34, and Telefunken

12AX7. These tubes went out of production many years ago and now
sell for rapidly escalating prices due to the pressures of supply and
demand. NOS prices will only increase as the finite number of those
tubes gets smaller every year. (You may be interested to know that,
even though Western Electric stopped producing 300B tubes some
time ago, they started production again when they discovered that
300Bs were selling for upwards of $500 each!)
Most tube types are made by more than one manufacturer. Different
construction techniques, tolerances, and materials can result in dif-
ferences in their sonic characteristics. For instance, military grade
tubes are often built more ruggedly – they’re more reliable and more
consistent – than the same type of tube built strictly for commercial
applications. Increased ruggedness also often translates into greater
power-handling capability and thus longer life. In addition, this can
result in reduced “microphonic” tendencies and/or hum and noise.
Microphonics is a term used to describe a tube's audible susceptibili-

ty to shock and vibration (whether acoustical or mechanical) due to
loose mechanical elements inside the tube itself. This can be mani-
fested as a ringing or pinging sound heard through your speakers
when the component containing the microphonic tube(s) is touched
(e.g. via front panel controls), exposed to severe mechanical vibration
(e.g. foot stomps on the floor) or acoustical vibration (e.g. voices) in
severe cases of microphony. Microphonics are often difficult to com-
bat. Some solutions are to replace the microphonic tubes them-
selves, isolate the component containing the microphonics (via a
compliant suspension), or use a commercially available compliant
dampening ring on the tube itself to reduce the effects of minor
vibration.
Also, it is important to note that tube quality will often vary between
manufacturers – thus, some manufacturer's tubes carry a price pre-
mium. Moreover, tube prices can often vary depending on what you
are actually buying – for example, you may buy raw, untested stock
for one price or, the very same tube which has first been selected,
tested and matched (via commercial or military tube testers or pro-
prietary, computer-based, testing equipment) for a given set of char -
acteristics, at another much higher price. However, given the appli-
cation, your interest in doing the selecting yourself, and your budget,
46
these "premium" tubes may be more appropriate for your require-
ments. Trying different tube types is easy. First, find out what tubes
are used in your system. Read your owner’s manual or check out the
tube sockets on the chassis – you’ll frequently find the tube type
marked for your convenience. Also, make a note of which tube types
are installed in the unit for future reference.
Our best advice is to read the owner’s manual that came with your
equipment. Its designers know what works best in the equipment
they crafted and there will probably be some valuable suggestions to
follow.
When searching for alternative tubes, be aware that there are usually
several different code designations – North American commercial
(e.g. 6DJ8), European commercial (e.g. ECC88), manufacturer, mili-
tary (JAN or JHS prefixes), industrial (e.g. 6922 or 7308) and special
service application (e.g. STR prefix) – for each tube type. The follow-
ing substitution chart will help:
Table I
TUBE TYPE ALTERNATES
12AX7 6681, 7025, 7729, ECC83, ECC803, E83CC
12AU7 5814, 5963, 6189, 6680, 7730, ECC82, ECC802, E82CC
12AT7 6201, 6679, 7728, CV4024, ECC81, ECC801, E81CC
6DJ8 6922, 7308, CV2492, ECC88, ECC808, E88CC
6SL7 6SU7, 5691*, 6188, ECC35, CV569, CV1985
6SN7 5692*, ECC32, CV1988
EL84 EL84M, 7189, 6BQ5
6CA7 EL34, E34L, KT77
6L6 5881, 5932, KT66*
6550 KT88, KT90, KT99, KT100
* These types should be checked for compatibility with the circuit they are intended to be used in as they consume higher filament current.
47
Cooking at the Right Temperature:

Biasing
Another factor to consider when changing tubes is bias. Briefly stat-
ed, bias is a voltage applied to a tube’s grid to insure that the tube
operates according to the designer’s intentions. Bias is usually very
important for output tubes in power amplifiers, and most amplifiers
provide a means to adjust bias for best operation.
Remember George Orwell’s famous book Animal Farm ? If you do,

you’ll probably remember the classic statement, “All animals are
equal but some animals are more equal than others.” Unfortunately,
all tubes are not the same. Subtle design differences, dissimilar mate-
rials, and manufacturing inconsistencies all contribute to the fact that
even “matched” tubes are sometimes not perfectly identical.
Adjustable bias gives us a way to minimize the effects of these differ-

ences and to optimize each tube to work in sonic harmony with its
peers. And there’s a potential financial bonus here, too, as biasing
makes the amplifier less dependent on expensive sets of closely
matched tubes for optimum performance.
There are two types of bias adjustments: manual and automatic.

Amplifiers with manual adjustments usually include a variable
potentiometer for increasing or decreasing bias current and a way to
monitor the current flow (with a meter or LED array).
Some amplifiers use what is called “cathode self-bias”. This type of

bias is somewhat misleading because, in order to obtain an optimum
bias for each tube, both a DC balance and a bias adjustment are nec-
essary. This operation is really no simpler than are conventional
“fixed” bias adjustments. In fixed bias amplifiers (by far the most
prevalent types) a simple bias adjustment is provided, usually for
each individual tube. These amps have the advantage of greater mea-
sured power output as compared to cathode self-bias types.
Other amplifiers have automatic biasing in which the circuit

automatically accommodates minor differences in tube properties. In
most cases, a servo-mechanism or feedback comparator provides
48
these adjustments. In practice, these circuits often require internal
adjustments to bring the tubes within a certain window of adjustment
— especially when a new set of output tubes is installed. These inter-
nal adjustments are often more complicated than conventional adjust-
ments! For this reason, servo-biasing is rarely seen in tube amplifiers.
If your amplifier has manual bias, you’ll no doubt find detailed

instructions in the owner’s manual. In any case, don’t worry — if you
can turn on your kitchen sto ve, bias adjustment is not a challenge!
Keep ‘em Fresh!

Nothing lasts forever but tubes operated at their rated voltage and
current can and will last a long time, presuming, of course, that you
start out with quality tubes.
Small signal tubes in particular will last for many years. Larger power
tubes are also surprisingly long-lived but, because of their greater cur-
rent consumption and heat generation, usually don’t last as long as
their smaller cousins.
Most tubes with dubious performance characteristics are weeded out

before they leave the factory or by equipment manufacturers them-
selves before they’re put into components. As tubes get older, they can
start sounding softer and slightly less detailed. Tubes generally don’t
get old before their time. They have a life cycle very similar to humans.
Their performance initially improves during the first few hundred
hours, followed by an extended performance plateau region. Finally,
after several thousand hours of use, they slowly f-f-f-fade away.
Running tubes outside their operational guidelines for voltage and

current flow is the quickest way to insure their early demise. This usu-
ally happens for one of two reasons: it can be done deliberately
(though ignorantly) through “over the edge” circuit designs that
exceed a tube’s SAO (Safe Area of Operation, aka “Design Maximum
Rating”), or an internal component may unexpectedly fail and cease
to maintain correct working conditions for the tube. Occasionally, a
tube may self-destruct for no apparent reason.
49
To forestall this possibility, tubes ABSOLUTELY need adequate venti-

lation. Although this is true for ALL electronic components, it is par-
ticularly true for tube components as the amount of heat they gener-
ate is substantially higher than equivalent solid-state circuits. Tube
power amplifiers in particular need unrestricted air flow and should
generally not be placed in any small enclosed area.
Onion Ice Cream: Some Final Thoughts

on the Transistor
In June, 1948, Bell Telephone Laboratories announced the develop-
ment of a small device called the transistor that could duplicate prac-
tically all the functions of a vacuum tube while using far less energy
(Fig. 36). The transistor was a truly staggering invention and earned
its developers (Drs. William Shockley, John Bardeen, and Walter
Brattain) the Nobel Prize for Physics in 1956.
Because of the transistor’s small size, a whole new area of electron-

ics opened up, allowing the development of such things as hearing
aids, pocket radios, and other small devices that we now take for
granted. Although the transistor has several advantages over the vac-
uum tube, these advantages are not necessarily beneficial in many
audio applications, especially where size and power consumption
are not major disadvantages.
Fig. 36. Schematic diagram of a p-n junction.
50
Clearing the Table
In fact, tubes have several advantages over transistorized circuitry.
Here’s a summary for quick reference:
• Tubes produce predominantly low-order distortion. Transistors, in

addition to low-order, produce greater levels of high-order distortion.
Distortion which is low order is closer to the musical fundamental
(e.g. 2nd or 3rd order harmonic), while high order is further away from
the musical fundamental (e.g. 9th, 11th, 13th order harmonic).
Although both are undesirable when reproducing an audio signal,
high-order distortion products are the most objectionable as they are
dissonant with (further away from the) musical fundamentals.
• Tubes have better manners. When pushed close to their power lim-
its, all amplifiers “run out of steam” and sound quality generally
deteriorates. Although different amplifiers behave differently in this
regard, you can safely say that the sound gradually loses clarity and
focus while becoming homogenized and strident. Tube circuits “lose
their composure” far more gradually than do solid-state circuits and
generally give you more coherent sound regardless of the music’s
dynamic range.
When pushed beyond their operating capabilities, all amplifiers

limit, or clip, the output signal. Nonetheless, even under these
extreme conditions, tube amplifiers usually exhibit far more tolerable
behavior than solid-state components which often sound coarse and
raspy when pushed. In contrast, tube amps are usually perceived to
be more graceful, polite, and coherent while reproducing demanding
musical peaks. This is one reason why many connoisseurs find that
tube amps sound more powerful than similarly rated transistor amps
– partially explaining the popular belief that “tube” watts are twice as
powerful as “solid state” watts.
• Tube circuits are usually easier to repair. Although this might sound
a bit strange at first, remember that tubes tend to age in a very
gradual manner. Moreover, when there is a problem with a tube-
based product, it is usually associated with the tube itself, not
51
the accompanying circuitry and thus, can be rectified by simply

changing the tube. In addition, there are still a large number of tubes
available to replace those originally used in components thirty years
old! Even when you can’t get original replacement types, chances are
very good that there are equivalents still being made that will work
just fine, thank you.
In contrast, transistors, even though fairly reliable, tend to fail in

more catastrophic ways. They’re more persnickety, too, in that they
tend to be highly specialized devices that not only must be precisely
matched in many cases, but in other cases must be replaced by the
exact brand and type of transistor. If your component is more than
ten years old, you may have real difficulty in getting the exact device
you need to replace one that has failed. And don’t forget the fact that
tubes simply plug in! Compare that to the delicate soldering needed
to replace defective transistors.
In fairness to transistors, they do have one tremendous advantage

over tubes: they are complementary devices; i.e., there are two types
of transistors, npn and pnp, that allow circuits to be designed that have
zero DC offset at the output (this is known as “complementary sym-
metry”). They also have a low output impedance. These two factors
allow transistors to drive loudspeakers directly without an output
transformer. The quality of the output transformer thus becomes the
key to high quality sound from tube amps.
52
Tube Futures
Tubes have a bright future!

They precipitated the electronics revolution and have a rich heritage
dating back to the turn of the century. As the new millennium
approaches, vacuum tube audio technology is still developing and
prospering to levels of popularity greater than at any time over the
last 25 years. Modern tube designs provide a level of musicality and
performance which is unobtainable by any other electronic means,
uniquely preserving the visceral emotional experience in the process.
There are dozens of manufacturers of tube (or valve) equipment

offering you, the audio enthusiast, an almost limitless combination
of design approaches, tube types, sonic flavors and price points.
Therefore, given this richness of choice, there is bound to be a prod-
uct which will suit your particular taste and budget.
We hope that this connoisseur's guide will contribute, in some

small way, to the ongoing future of tube audio by giving you the
background, knowledge and tools to fully appreciate, and partici-
pate in, this often passionate pursuit. The final, and most valuable
test is to listen to your favorite music through a tube-based system
or component.
When choosing tube gear for your system, some of the factors you
will want to consider in your evaluation should include:
• does the design use commonly available tubes?

• has the manufacturer adopted a conservative design approach?
• does the unit look well built inside and exude craftsmanship outside?
• does the unit use high quality, brand name parts throughout the design?
• do I like the sound of the unit with MY equipment in MY home?
• does the manufacturer extend a reasonable warranty commensurate with the
equipment’s purchase price?
We hope you will enjoy the richly satisfying sound that tubes, at
their best, can bring to your musical listening experience.
53
FOOD FOR
THOUGHT
54
Bibliography
Basic Electronics and High Fidelity Te c h n i q u e s

Norman Crowhurst, Understanding Hi-Fi Circuits (Gernsback Library,
Inc., NY, 1957)
Bernard Grob, Basic Electronics (McGraw-Hill, Inc., NY, 1959)
Robert Harley, The Complete Guide to High-End Audio (Acapella

Publishing, Albuquerque, NM, 1995)
H.A. Hartley, “Aesthetics of Sound Reproduction” (Wireless World,

Jul/Aug, 1944)
Henry Jacobowitz, Electronics Made Simple (Doubleday & Co., Inc., NY, 1958)
Walter G. Jung and Richard Marsh, “Picking Capacitors” (Audio,

64:2&3, 1980; Feb pp. 52-62; Mar pp. 50-62)
John H. Newitt, High Fidelity Techniques (Rinehart & Co., Inc., NY, 1958)
Circuits and Circuit Design

W.T. Cocking, “High Quality Amplification” (Wireless World, May 4,
1934, 34.18, pp. 302-304)
W.T. Cocking, “Phase-Splitting in Push-Pull Amplifiers” (Wireless

World, Apr 13, 1939, pp. 340-344)
N.H. Crowhurst, “Output Transformer Specifications” (Audio, Jun

1957, pp. 20-23, cont. pp. 51-52)
J.L. Daley, ed., Principles of Electronics and Electronic Systems (United

States Naval Institute, Annapolis, MD, 1956)
J.R. Edinger, “High-Quality Audio Amplifier with Automatic Bias

Control” (Audio Eng., Jun 1947, pp. 7-9, cont. p. 41)
Scott Frankland, “Single-Ended vs Push-Pull” (Stereophile, Dec 1996,

Jan 1997, Feb 1997)
55
Irving M. Gottlieb, Regulated Power Supplies (TAB Books, Blue Ridge

Summit, PA, 4th ed., 1992)
David Hafler and Herbert I. Keroes, “An Ultra-Linear Amplifier”

(Audio Eng., Nov 1951, pp. 15-17)
David Hafler and Herbert I. Keroes, “Ultra-Linear Operation of the

Williamson Amplifier” (Aud. Eng., Jun 1952)
F. Langford-Smith and A.R. Chesterman, “Ultra Linear Amplifiers”

(Radiotronics, 20:5/6/7, May/Jun/Jul 1955)
F. Langford-Smith, ed., Radiotron Designer’s Handbook (Amalgamated

Wireless Valve Co. Pty. Ltd., Sydney, Australia, 4th ed., 1953)
J.D. Ryder, Engineering Electronics (McGraw-Hill, Inc., NY, 1957)
D.T.N. Williamson, “Design for a High Quality Amplifier” (Wireless

World, Apr 1947, pp. 118-121; May 1947)
History
Henry B.O. Davis, Electrical and Electronic Technologies: A Chronology of
Events and Inventors from 1900 to 1940 (The Scarecrow Press, Inc.,
Metuchen, NJ, and London, 1983)
M.D. Fagen, ed., A History of Engineering and Science in the Bell System,
the Early Years (1875-1925) (Bell Telephone Laboratories, Inc., 1975)
W. Rupert MacLaurin and R. Joyce Harman, Invention and Innovation

in the Radio Industry (MacMillan Co., NY, 1949)
George Shiers, Bibliography of the History of Electronics

(The Scarecrow Press, Inc., Metuchen, NJ, 1972)
P s ychoacoustics and Distortion Products

D.E.L. Shorter, “The Influence of High-Order Products in Non-Linear
Distortion,” (Electronic Eng., Apr 1950, pp. 152-153)
56
Harry F. Olson, Music, Physics, and Engineering (Dover Pubs., Inc., NY, 1967)
Fritz Winckel, Music, Sound, and Sensation (Dover Pub., Inc., NY, 1967)
Reference Books
Norman Crowhurst, Audio Measurements (Gernsback Library, Inc., NY, 1958)
Rudolf F. Graf, Dictionary of Electronics (Howard W. Sams & Co., Inc.,

NY, 1962)
The Howard W. Sams Engineering Staff, Tube Substitution Handbook

(Indianapolis, IN, 1973)
Bill Perkins, The PEARL Archive (Perkins Electro-Acoustic Research

Laboratory, Calgary, Alberta, Canada, 1996). This is a prime resource
for books and articles about tube circuits.
John W. Stokes, 70 Years of Radio Tubes and Valves (1992). A gorgeous

gallery of tube photography and lore. An indispensable resource for
tube collectors.
World Tube Directory, (Glass Audio, Peterborough, NH, 1996). This

directory is a prime resource for tube-related parts and equipment
world-wide.
Tube Physics and Manufacturing
A.R. Balaton , “Tube Manufacturing at Western Electric: The WE

300B” (J. Audio Eng. Soc., 37:11, Nov 1989, pp. 950-958)
L.R. Koller, The Physics of Electron Tubes (McGraw-Hill Book Co., Inc., NY, 1934)
O.H. Schade, “Beam Power Tubes” (Proc. IRE, 26.2, Feb 1938, pp. 162-176)
Karl R. Spangenberg, Vacuum Tubes (McGraw-Hill Book Co., Inc., NY, 1948)
57
BITS & BYTES
58
How To Reach Us
SONIC FRONTIERS, INC.

2790 Brighton Road
Oakville, Ontario,
Canada. L6H 5T4.
Phone: (905) 829-3838

Fax: (905) 829-3033
E-Mail: [email protected]
Website: www.sonicfrontiers.com
THE PARTS CONNECTION

2790 Brighton Road
Oakville, Ontario,
Canada. L6H 5T4.
Phone: (905) 829-5858

Fax: (905) 829-5388
E-Mail: [email protected]
Website: www.sonicfrontiers.com/TPC
Special Thanks...
...to the technical staff at Sonic Frontiers for testing all the
recipes, Scott Frankland for stirring the beaucoup spice into
the technical ingredients, and TechniCom Corporation for
beating the lumps out of the verbal gravy.
Scott Frankland’s E-Mail:

[email protected]
TechniCom’s E-Mail:
[email protected]
SONIC FRONTIERS, INC. is the Manufacturer

OF THE
&
TUBE ELECTRONIC PRODUCT LINES.
COPYRIGHT AUGUST 1997
SKU# 57416 59
60
61

A Taste of Tubes - The Connoisseur's Cookbook - 1997, 67p

Uploaded by

Copyright:

Available Formats

A Taste of Tubes - The Connoisseur's Cookbook - 1997, 67p

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

A Taste of Tubes - The Connoisseur's Cookbook - 1997, 67p

Uploaded by

Copyright:

Available Formats

What is the book about?

What is the book about?

What are some of the topics covered in the book?

What are some of the topics covered in the book?

$5.

THE SENSORY DELIGHTS OF

Written for tube lovers of all persuasions and levels of expertise.

Written for tube lovers of all persuasions and levels of expertise.

T UBE ELECTRONIC PRODUCT LINES.

COPYRIGHT AUGUST 1997

Tube History I: A Foretaste of Tubes Page 5

Tube History II: Amplifiers Du Jour Page 9

Cooking the Signal: Tubes or Transistors? Page 14

MEAT & POTATOES Page 16

Tubes for All Tastes: Spicing the Circuits Page 22

Cooking with Tubes Page 28

Tube Cuisine In Three Easy Classes Page 37

Nourishing Your Playback System Page 40

JUST DESSERTS Page 42

FOOD FOR THOUGHT Page 54

BITS & BYTES Page 58

How to Reach Us Page 59

A Taste of Tubes is your guide to the ever-finer subtleties in

There is food here for everyone — from nouvelle gourmand

If you should feel hesitant to dive into some of the thicker

Our advice is simple – skim through A Taste of Tubes at your

Since then, however, the transistor

But a sizeable faction within

Why? Transistors didn’t suddenly rot overnight to become

To answer these questions, let’s look at the beginnings of the

The Family Tree of Thermionic Tubes.

Edison Discovers the Genie in the Lamp

This led him to insert into the bulb a

Fleming’s Electronic Aerial

A few years later, De Forest began to experiment with his three-element

After explaining his approach, Cocking compared triodes to pentodes

Cocking’s amplifier soon became known as “The Wireless World

Williamson Stirs the Pot

Thus, the evolution of Cocking’s “Wireless World Push-Pull Quality

In 1946, Avery Fisher introduced the first commercial high fidelity

The Pentode’s Revenge

Quad’s Potent Pentode Recipe

This technique produced local feedback in accordance with the AC

McIntosh’s Pentode Pie`ce de Resistance

The editors of Audio Engineering hailed the McIntosh as “the first

Hafler and Keroes Go Ultra

Cooking the Signal:

Purported to be more reliable than tubes, transistors certainly didn’t produce as

High-powered output transistors in particular were extremely finicky and would

A few die-hard companies, however, bucked

Other amplifier circuits, including the soon-to-be-

As we mentioned before, tubes were necessary for all types

However, we should begin our review of vacuum tube tech-

All tubes have two basic electrodes: one

101: Thermionic Emmission

Strictly speaking, the plate attracts electrons

Controlling the electron flow is crit-

Tubes for all Tastes:

Common Tube Rectifiers: 5AR4, 5Y3GT, 6X4, 12X4, 5U4G, GZ37